Yamaha DM7 Käyttöohjeet

EN

DIGITAL MIXING CONSOLE

DM7 StageMix User Guide

Table of contents

Introduction 4

DM7 StageMix...........................................................................................4

Software requirements..............................................................................5

Preparation 6

Wi-Fi setup...............................................................................................6

Network setting for the DM7 series..............................................................7

Configuring iPad network settings.. ............................................................ 8

Using DHCP.. ..............................................................................................................................................................................8

Using a fixed IP address.............................................................................................................................................................9

Configuring StageMix...............................................................................10

Controls and functions 12

HOME screen.. ........................................................................................ 12

HOME screen.. ..........................................................................................................................................................................12

FADER MODE.. ..........................................................................................................................................................................15

SCENE screen..........................................................................................23

UTILITY screen........................................................................................25

UTILITY screen..........................................................................................................................................................................25

CONNECT screen......................................................................................................................................................................26

MUTE/TEMPO screen.. .............................................................................................................................................................27

OSCILLATOR screen.. ...............................................................................................................................................................28

CUSTOM FADER BANK screen..................................................................................................................................................30

USER DEFINED BUTTONS screen.. ..........................................................................................................................................32

PREFERENCE screen.. ..............................................................................................................................................................34

ABOUT screen...........................................................................................................................................................................37

SELECTED CH indicator.............................................................................38

SELECTED CH indicator.. .........................................................................................................................................................38

EQ screen..................................................................................................................................................................................39

DYN screen.. .............................................................................................................................................................................42

INSERT screen.. ........................................................................................................................................................................46

DELAY Screen.. .........................................................................................................................................................................49

CH NAME screen.......................................................................................................................................................................50

RACK Screen...........................................................................................52

2

Table of contents

Troubleshooting 53

Troubleshooting.. ................................................................................... 53

3

Table of contents

Introduction

DM7 StageMix

DM7 StageMix is an iPad application for wirelessly controlling DM7 series equipment.

DM7 StageMix gives the sound engineer the freedom to directly and remotely control parameters of the DM7

Series console from the stage, while listening to the results from the vantage point of the performers. And

because it's an iPad with its simple, direct style of interaction, you'll find setup faster and making the live

sound settings for the DM7 all the more pleasant.

Note

(

The software and this document are the exclusive copyrights of Yamaha Corporation.

Copying or modifying the software or reproduction of this document, by any means, whether in whole or

in part, is expressly forbidden without the written consent of Yamaha Corporation.

Yamaha Corporation makes no representations or warranties with regard to the use of the software and

documentation and cannot be held responsible for the results of the use of the software and this

document.

Copying of commercially available music sequence data and/or digital audio files is strictly prohibited

except for your personal use. If you plan to use such data or files, consult a copyright specialist.

Illustrations of product screens that appear in this document are for instructional purposes only, and may

appear somewhat different from the screens that are displayed on your computer.

Information about system software and changes to certain product functions or specification due to

updates to the software can be found in the related documentation.

Apple, theApple logo, and iPadare trademarks of Apple Inc., registered in the U.S. and other countries.

IOS is a trademark or registered trademark of Cisco Systems, Inc. in the U.S. and other countries, and used

under license.

The company names and product names in this document are the trademarks or registered trademarks of

their respective companies.

4

Introduction > DM7 StageMix

Software requirements

Following is an explanation of the operating environment for DM7 StageMix.

(Apple iPad 5th generation or later

(Supported OS: iPadOS

(Yamaha digital mixing console DM7 Series V1.0 or later

(Wi-Fi access point

(Ethernet cable (used to connect the DM7 Series to the Wi-Fi access point)

5

Introduction > Software requirements

Preparation

Wi-Fi setup

Refer to the instruction manual for your device to set up the Wi-Fi access point. Although no special settings

are required, we recommend that you configure security settings, such as WPA, to prevent any outside

intrusion into the network.

6

Preparation > Wi-Fi setup

Network setting for the DM7 series

1Use an Ethernet cable to connect the network port of the DM7 series to the Wi-Fi

access point.

If you plan to connect it to a legacy access point that does not feature the AUTO-MDIX

function, you will need to use a cross cable. Since many newer device models support the

AUTO-MDIX function, you will be able to use either a straight cable or a cross cable.

2Make sure that the Ethernet cable is connected to the LAN port of the Wi-Fi device.

(Do not connect the cable to the WAN port.)

3Open the SETUP screen on the DM7 series .

4Touch the NETWORK popup button in the CONSOLE STATUS field to open the

NETWORK screen.

5On the FOR MIXER CONTROL tab, set the CONSOLE IP SETTING to ENABLE, and then

specify the IP address in the IP address segment for the Wi-Fi access point.

Network switching

You can connect to a network using a wired connection in addition to a wireless connection. A Lightning to

USB 3 Camera Adapter (or a USB- C-USB adapter) and a USB Ethernet Adapter are required to use a wired

connection. You can switch between a wireless and wired connection when offline.

7

Preparation > Network setting for the DM7 series

Configuring iPad network settings

Using DHCP

DHCP (Dynamic Host Configuration Protocol) is a network protocol that enables the server to automatically

assign an IP address to the devices. Follow the steps below to set up the iPad using DHCP.

1Open the Settings menu on the iPad.

2Select Wi-Fi, and then select the proper network.

3Tap the blue icon located to the right of the currently-selected network name to

display a screen that enables you to edit the IP address.

4Select [DHCP], and then make sure that the iPad has received IP Address, Subnet

Mask, Router, and DNS data.

5If the data is not displayed, select Renew Lease.

6Once the setting is complete, exit the Settings menu.

NOTE

(When connecting with AUTO (“CONNECT screen”(p.26)), make sure that the IP address uses the same subnet for the DM7 series.

(If the DHCP setting is not enabled after Step 5, check your DHCP server settings. Alternatively, use a fixed IP address to set up your

iPad.

8

Preparation > Configuring iPad network settings

Using a fixed IP address

1Open the Settings menu on the iPad.

2Select Wi-Fi, and then select the proper network.

3Tap the blue icon located to the right of the currently-selected network name to

display a screen that enables you to edit the IP address.

4Select [Static].

5Set IP address. When connecting with AUTO (“CONNECT screen”(p.26)), enter only

the last set of numbers (4th octet) of the IP address that is included in the IP

address of the DM7 series.

(Example: If the IP address for the DM7 series is “192.168.0.128”, enter “192.168.0.127” for the

iPad.)

6Subnet Mask: Enter “255.255.255.0”.

7Router: Enter the IP address for the Wi-Fi access point.

This IP address is usually labeled on the bottom of the Wi-Fi device, or printed in the

instruction manual.

8DNS: Enter the IP address for the Wi-Fi access point. (Same as explained in Step 7.)

9Press the Home button on your iPad and exit the Settings menu.

9

Preparation > Configuring iPad network settings

Configuring StageMix

Launch StageMix.

The SELECT MIXER screen appears. This screen enables you to do the following:

(Engage Offline Demo mode, use the StageMix features, and navigate the user interface.

(Select the DM7 series on the network and start using StageMix.

Offline Demo mode

Press the OFFLINE button in the SELECT MIXER screen to engage Offline Demo mode to navigate the

StageMix application while the DM7 series is offline (that is, not connected to StageMix). Please note that the

level meters and most scene memory features will be disabled in this mode.

Selecting a console and starting the operation

Once the iPad is set up to link to the DM7 series , select the system from the list, and then press the

[CONNECT]button.

10

Preparation > Configuring StageMix

If the maximum number per control surface/console (two instances) of StageMix installations have already

been connected to the DM7 series , a prohibiting icon will appear to the left of the IP Address. If you select a

DM7 series that is displayed with a prohibiting icon in StageMix, and then you press the [CONNECT]button, a

message will appear indicating that the connection was not made.

Once StageMix receives parameter data from the DM7 series , the StageMix setup process is complete. If a

connection between StageMix and the DM7 series cannot be established, refer to the Troubleshooting

section at the end of this User Guide.

11

Preparation > Configuring StageMix

Controls and functions

HOME screen

The HOME screen is the main screen of StageMix. It is displayed each time you start StageMix.

You can return to this screen by tapping [HOME] in the Toolbar area.

Meter

area

Main

area

Toolbar

area

Meter area

This area displays input level, output level, and fader levels. In SENDS ON FADER mode, it displays send

levels. The Meter area offers INPUT mode, OUTPUT mode, and CUSTOM mode. Use the switch button on the

left side or swipe the Meter area upward repeatedly to switch these modes in sequence. The Meter area is in

INPUT mode when you start StageMix for the first time. The next time you start StageMix, the area will be in

the mode that was used most recently.

INPUT mode

OUTPUT mode

12

Controls and functions > HOME screen

CUSTOM mode

The screen in each mode is divided into 12 channel blocks. In INPUT mode and OUTPUT mode, the STEREO

OUT, CUE A, and CUE B meters will be displayed on the right end. In CUSTOM mode, a meter for the channel

assigned by the user will be displayed. The CUE A/B meters will appear only if CUE is turned on. Tap CUE A/B

to clear CUE and hide the CUE A/B meters. Meters are displayed in green for up to –18 dB, yellow for up to 0

dB, and in red for levels higher than 0 dB. You can change the metering point using “Meter Point” in the

PREFERENCE screen (page 27). Note that the metering point for DCA is fixed at Post On. The fader level for

each channel is indicated by a white line. A thick white line appears when the fader is at the nominal (0 dB)

level. If a channel is turned off, the background of the meter turns black and the meter itself appears in gray.

The channels displayed in the Main area are surrounded by a white box in the Meter area. You can drag this

box left or right, or tap it to select other channels to be displayed in the Main area. Tapping it repeatedly will

switch the Main area between displaying each 12-channel group. While the SELECTED CH screen is displayed,

only the selected channel will be surrounded by a white box. If you switch to another channel, the white box

will move accordingly. In SENDS ON FADER mode, the level meter is displayed according to the Show Send

Levels in Meter Bridge setting in the PREFERENCE screen. In this case, the fader level bar is displayed in the

color assigned to the destination channel. Drag the Meter area down to enter Full Screen mode.

Main area

The Main area displays details of the content selected in the Toolbar area. Each screen you can access from

the Main area is explained in the section that describes the Toolbar buttons.

The Main area displays details of the content selected in the Toolbar area. Each screen you can access from

the Main area is explained in the section that describes the Toolbar buttons.

Toolbar area

This area is always displayed near the bottom of the HOME screen.

g4 7M

 S

D

13

Controls and functions > HOME screen

aFader mode switch buttons

These buttons enable you to select the Fader display mode in the Main area of the HOME screen. If none of the

options is selected, NORMAL mode will be used. If you select SENDS, the channel ID, name, icon, and color of the send

destination will appear to the right of the SENDS button.

Tap this send destination indicator to display the send destination list (page 13), which enables you to change the

send destination. Press and hold down the send destination indicator to display the send destination channels

horizontally. Press and hold down the SENDS button to switch the control target between the send level and send

pan. Press and hold down the GAIN button to switch the control target between analog gain and digital gain.

bScene indicator

This area displays the number and name of the scene that is currently selected. If a scene other than the currently-

applied scene is selected, the scene number will flash. Tap this area to display the SCENE screen. While the SCENE

screen is open, tap this area again to close the SCENE screen. If you change a parameter of the recalled scene, an Edit

indicator will appear in the upper-right corner of the area.

cUtility button

Tap this button to display the UTILITY screen.

dONLINE indicator

This indicator lights up while the system is online.

eHOME button

Tap this button to return to the HOME screen. If you have changed the Fader mode, the HOME screen will open in the

selected Fader mode.

fTool buttons

Tap each button to switch the display in the Main area. The tapped button will light up steadily. Tap the INSERT

button displays the plug-in, FX, and GEQ/PEQ buttons inserted into the selected channel. The button will not be

displayed if it is not inserted.

gMenu button

Tap this button to open the context menu that is applicable to the current screen. For more information on the menu,

refer to the section on each screen.

HOME screen menu

The following items are available in the context menu of the HOME screen.

(CH Copy： Stores the settings for the currently-selected channel in the copy buffer.

(CH Paste： Pastes the channel settings stored in the copy buffer to the currently-selected channel.

(CH Default： Initializes the settings for the currently-selected channel.

14

Controls and functions > HOME screen

FADER MODE

You can select the fader indication mode from NORMAL, SENDS (SENDS ON FADER) and GAIN by using the

Fader mode buttons. NORMAL is the default setting at the time of the application startup.

NORMAL SENDS GAIN

15

Controls and functions > HOME screen

When the fader indication mode is set to NORMAL or GAIN, a stereo channel is shown at the right edge of the

main area. By swiping this area to the left or right, you can switch the indication between ST A and ST B.

When the fader indication mode is set to SENDS, the send-destination output channel is shown at the right

edge of the main area.

When NORMAL or GAIN is selected When SENDS is selected

16

Controls and functions > HOME screen

NORMAL

aProcessing area

Displays the channel EQ, DYN, INSERT, DELAY, PAN. For EQ, DYN, INSERT or DELAY, tap this area to switch to a screen

that enables you to edit parameters for the SELECTED CH screen.

EQ DYN INSERT DELAY

For PAN, press and hold down the PAN value, and then drag the value to edit

bON button

Switches the channel on or off. This button lights up when it is turned on. While the channel is turned on, the button

will flash if a mute group (that includes this channel) is turned on. The button will also flash if a DCA group (that

includes this channel) is turned off.

17

Controls and functions > HOME screen

cCUE button

Tap this button to turn the channel’s cue on or off. The button lights up when it is turned on. To edit the cue, use the

Cue Operation Mode setting in the PREFERENCE screen. This button works as the SOLO button in Solo In Place mode,

and lights up red when it is turned on.

dFader

Drag the fader’s knob up or down to adjust the fader level. The fader stops at the nominal level (0 dB). You can then

continue to drag it up or down as desired. You can drag the fader left and right and then up and down to adjust it

more precisely. You can adjust multiple faders at the same time.

eMeter display

Two meters are displayed for paired channels.

fFader value

Displays the value of the current fader level. You can tap the value and then increase or decrease it by tapping the up

or down arrow.

gChannel name area

Displays the channel’s ID number, name, icon, and color. If two channels are assigned as a stereo pair, you can tap

this area repeatedly to toggle the displayed channel name. Double-tap the area to open the CH NAME screen.

18

Controls and functions > HOME screen

SENDS (SENDS ON FADER)

aPRE button

Switches between Pre Fader and Post Fader. The button lights up when it is turned on.

(On：Pre Fader

(Off：Post Fader

Press and hold down the button to display the following menu items: Select one of the menu items. The confirmation

message will appear. Tap the OK button to select Pre or Post for the desired channel(s) all together as a group.

All Mix/Matrix busses PRE for this channel

All Mix/Matrix busses POST for this channel

Current Mix/Matrix bus PRE for all channels

Current Mix/Matrix bus POST for all channels

bSEND ON button

The SEND ON button switches the send for the specified destination channel on or off. The CH ON button switches

the channel on or off.

cCUE button

Tap this button to turn the channel’s cue on or off. The button lights up when it is turned on. To edit the cue, use the

Cue Operation Mode setting in the PREFERENCE screen. This button works as the SOLO button in Solo In Place mode,

and lights up red when it is turned on.

19

Controls and functions > HOME screen

dFader

>Enables you to adjust the send level or send pan for the specified destination channel.

eSend level value

Displays the current send level or send pan value. You can tap the value and then increase or decrease it by tapping

the up or down arrow.

fChannel name area

Displays the channel’s ID number, name, icon, and color.

Send destination list

Tap the send destination indicator next to the Fader mode switch button to display the send destination list.

hMIX/MATRIX switch buttons

Switches the send destination list. The button for the currently-selected channel lights up. Stereo pair channels will

be surrounded by a white box

20

Controls and functions > HOME screen

Sivu latautuu ...

Yamaha DM7 Käyttöohjeet

Yamaha DM7 Käyttöohjeet

muilla kielillä