Yamaha ACD1 Omistajan opas

Merkki: Yamaha

Malli: ACD1

Luokka: Supplementary music equipment

Tyyppi: Omistajan opas

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manuale di istruzioni

Руководство пользователя

ACD1 Owner’s Manual

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not ﬁt into

your outlet, consult an electrician for replacement of

the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

speciﬁed by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

ACD1 Owner’s Manual

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF

CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Ampliﬁer Control Device

Model Name : ACD1

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception

is suspected.

(FCC DoC)

* This applies only to products distributed by (Perchlorate)

YAMAHA CORPORATION OF AMERICA.

This product contains a battery that contains perchlorate

material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batteri-

typ eller en ekvivalent typ som rekommenderas av apparat-

tillverkaren. Kassera använt batteri enligt fabrikantens

instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda

paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-

up.

• This apparatus contains a lithium battery for memory back-

up.

• Raadpleeg uw leverancier over de verwijdering van de bat-

terij op het moment dat u het apparaat ann het einde van de

levensduur of gelieve dan contact op te nemen met de verte-

genwoordiging van Yamaha in uw land.

•For the removal of the battery at the moment of the disposal

at the end of life please consult your retailer or Yamaha repre-

sentative ofﬁce in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small

chemical waste.

(lithium disposal)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modiﬁ-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this product

in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

tion of other electronic devices. Compliance with FCC regu-

lations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of

interference, which can be determined by turning the unit

“OFF” and “ON”, please try to eliminate the problem by

using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or colored GREEN or

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

• This applies only to products distributed by

Yamaha Music U.K. Ltd.

(3 wires)

ACD1 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited

to, the following:

• Only use the voltage speciﬁed as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the included power cord. If you intend to use the device in an area

other than in the one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have

it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings. If any liquid such as water seeps into the device, turn off

the power immediately and unplug the power cord from the AC outlet. Then

have the device inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet. Even when the

power switch is turned off, electricity is still ﬂowing to the product at the

minimum level. When you are not using the product for a long time, make

sure to unplug the power cord from the wall AC outlet.

• If several of the devices are mounted in an EIA-compliant rack, carefully

read the section “Precautions when rack-mounting the unit” on page 9.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not place the device in an unstable position where it might accidentally

fall over.

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Doing so may result in noise, both

in the device itself and in the TV or radio next to it.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-6 1/2

ACD1 Owner’s Manual

• Condensation can occur in the device due to rapid, drastic changes in

ambient temperature—when the device is moved from one location to

another, or air conditioning is turned on or off, for example. Using the

device while condensation is present can cause damage. If there is reason

to believe that condensation might have occurred, leave the device for

several hours without turning on the power until the condensation has

completely dried out.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(ports, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into

any gaps or openings on the device (ports, etc.) If this happens, turn off the

power immediately and unplug the power cord from the AC outlet. Then

have the device inspected by qualiﬁed Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

This device has a built-in backup battery that maintains data in internal

memory even when the device’s power is switched off. The backup battery will

eventually become depleted, however, and when that happens the contents of

the internal memory will be lost.* To prevent loss of data be sure to replace the

backup battery before it becomes fully depleted. When the remaining capacity

of the backup battery becomes so low that it needs to be replaced a “Low

Battery”, “Critical Battery” or “No Battery” message will appear on the display

during operation or when the device is powered on. If either of these

messages appears do not turn off the power and immediately transfer any data

you want to save to a computer or other external storage device, then have

qualiﬁed Yamaha service personnel replace the backup battery. The average

life of the internal backup battery is approximately 5 years, depending on

operating conditions.

* Data items maintained in the internal memory by the backup battery are as

follows:

• Current scene parameters and number.

• Device parameters (Device Setup, Utility, Network Setup, etc.).

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

● SPECIAL NOTICES

The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different

from those on your instrument.

•Windows is a registered trademark of Microsoft

Corporation in the United States and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Handling caution Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

European models

Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.

Inrush Current: 45A

Conforms to Environments: E1, E2 E3 and E4

For customers using the PC9500N, PC4800N, or PC3300N power ampliﬁers

If your system connects the PC9500N, PC4800N, or PC3300N power ampliﬁers to the ACD1, there may be cases in

which Amp Editor will not display the meters correctly for some power ampliﬁers. Please check whether this problem

has been corrected for the power ampliﬁer you’re using. If not, please contact your Yamaha dealer.

[Checking for the correction]

If the two alphabetical characters at the beginning of the serial number label on the back of the power amp are IL, IM, IN, IO, IP,

IX, IY, IZ, or JH, and no green circular label is afﬁxed immediately nearby it, then the product has not been corrected.

For customers using the T5n, T4n, or T3n power ampliﬁers

When monitoring or controlling the T5n, T4n, or T3n power ampliﬁers, set the GAIN switch of the T5n, T4n, or T3n to

[26 dB] to avoid clipping if you plan to input signals with a maximum input level of +24 dBu.

When the power ampliﬁer is connected to the ACD1, the electronic volume control inside the ampliﬁer will become

effective, and the maximum input level will become +18 dBu if the GAIN switch has been set to [32 dB].

Included Accessories

• AC power cord • Euroblock connector (16P)

• Rubber feet x 4 • Owner’s Manual (this document)

(5)-6 2/2

ACD1 Owner’s Manual

Introduction ........................................................................................................7

Related manuals and software ................................................................................................ 7

Features of the ACD1.............................................................................................................. 7

Terms....................................................................................................................................... 8

Supported amplifiers................................................................................................................ 8

Regarding firmware updates.................................................................................................... 8

Precautions when rack-mounting the unit................................................................................ 9

Preparation ............................................................................................................................ 10

Connection Examples .....................................................................................11

Connections with the PC-N or Tn series................................................................................ 12

Connections with the XP, XM, or XH series .......................................................................... 13

Connections with controllers from other manufacturers ........................................................ 13

Operations that can be performed from the panel .......................................14

Troubleshooting...............................................................................................15

Initializing the internal memory .............................................................................................. 15

Contents

ACD1 Owner’s Manual

Introduction

Thank you for purchasing the Yamaha ACD1 Ampliﬁer Control Device.

In order to take full advantage of the ACD1’s functionality and to ensure trouble-free

operation, please read this owner’s manual carefully before use.

After you have read the manual, keep it in a safe place for reference when needed.

Related manuals and software

This document explains mainly the initial connection. Manuals that contain detailed explanations of the ACD1

and Amp Editor, as well as the Amp Editor software itself, can be downloaded from the following page of the web-

site.

http://www.yamahaproaudio.com/downloads/

● List of related manuals

• In order to view the downloaded manuals, Adobe Reader must be installed in your computer. If you don’t have Adobe

Reader, please access the Adobe Corporation’s website at the following URL, and download Adobe Reader (free of

charge).

http://www.adobe.com/

Features of the ACD1

The ACD1 is an ampliﬁer control device with the following features.

■ Monitor and control ampliﬁers from Amp Editor

The ACD1 and ampliﬁers connected to the ACD1 can be monitored and controlled from a LAN-connected computer in

which the Amp Editor application software is installed. The ACD1 can also monitor the output signal of the connected

ampliﬁers and control their power supply On/Standby status.

■ Monitor and control up to 40 ampliﬁers

A single ACD1 unit is able to monitor and control up to 40 connected ampliﬁers (a maximum of eight XP/XM/XH series

units, and a maximum of 32 PC-N/Tn series units can be connected).

By connecting multiple ACD1 units in a single network, a larger number of ampliﬁers can be monitored and controlled via

Amp Editor.

ACD1 Reference Manual Provides a detailed explanation of the ACD1’s panel operations, etc..

Amp Editor Installation Guide Explains the installation procedure for Amp Editor and the uninstallation

procedure.

Amp Editor Owner’s Manual Explains how to set up Amp Editor and the ACD1, and how to use Amp

Editor.

NOTE

ACD1 Owner’s Manual

Terms

This section explains terminology speciﬁc to the ACD1.

■ Scene

Settings such as power-on/standby or mute for each ampliﬁer are called a “scene.” By recalling a scene, the saved settings

can be immediately applied to the ampliﬁers.

■ Scene link

Settings for simultaneously recalling scenes for multiple ampliﬁers within an area are called a “scene link.” By recalling a

scene link, scenes can be simultaneously recalled for multiple ampliﬁers. Scene links can be created and recalled using

Amp Editor.

Supported ampliﬁers

As of September 2009, the following ampliﬁers support connection with the ACD1.

• XP series : XP7000, XP5000, XP3500, XP2500, XP1000

• XM series : XM4180, XM4080

• XH series:XH200

• PC-N series : PC9501N, PC6501N, PC4801N, PC3301N, PC2001N, PC9500N, PC4800N, PC3300N

• Tn series : T5n, T4n, T3n

*For the most recent information, refer to the following website.

http://www.yamahaproaudio.com/

Regarding ﬁrmware updates

The ﬁrmware version of the ACD1 itself can be checked from the ACD1’s panel and from Amp Editor. You can

update the ﬁrmware via Amp Editor. For the update procedure, refer to the Amp Editor owner’s manual.

You can download the latest ﬁrmware from the download page of the following Yamaha website.

http://www.yamahaproaudio.com/downloads/

ACD1 Owner’s Manual

Precautions when rack-mounting the unit

This unit will operate stably in an environmental temperature of 0–40°C. If you install this device together with

multiple units of the same device or other devices in a EIA standard rack, the heat produced by the various

devices may raise the ambient temperature inside the rack, resulting in inefﬁcient performance. To ensure that the

heat produced by this device can be dissipated appropriately, please ensure the following conditions when rack-

mounting it.

• When mounting this device together with other heat-producing equipment such as power ampliﬁers, leave 1U or more

space between it and other devices (including other ACD1 units). Install a ventilation panel in this vacant space or leave it

open to ensure adequate cooling.

• Leave the back of the rack open, and allow at least 10 cm of space between the rack and the wall and ceiling to ensure ade-

quate cooling. If you’ve installed a fan kit, there may be cases in which closing the back of the rack will produce a greater

cooling effect. For details, refer to the owner’s manual of your rack or fan kit.

■ When mounting the ACD1 together with compatible ampliﬁers

• Do not mount another ACD1 unit or ampliﬁer above or below the ACD1.

ACD1

ampliﬁer

ACD1

ampliﬁer

ventilation panel

ampliﬁer

ampliﬁer ampliﬁer

ampliﬁer

ventilation panel

ventilation panelventilation panel

1) When mounting only one ACD1 in

a rack

2) When mounting multiple ACD1

units in a rack

CAUTION

ampliﬁer

ACD1

ampliﬁer

ACD1 Owner’s Manual

Preparation

• Be sure to turn all devices OFF before connecting AC mains power.

First plug the female-connector end of the included AC cable into the [AC IN] socket on the rear panel of the ACD1, then

plug the male plug into an appropriate AC outlet. Be sure to use an AC outlet of the voltage speciﬁed for the device.

•To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn the

devices on in the following order: audio sources, mixer (such as M7CL or PM5D), ACD1, and ﬁnally power ampliﬁ-

ers. Reverse this order when turning power off.

• If you power-on the ampliﬁer before the ACD1, the ampliﬁer may be ready before the mute or level setting of the

ACD1 becomes effective, resulting in an unexpected loud sound.

• If you power-off the ACD1 before your XP/XM/XH series ampliﬁers, the ampliﬁer’s settings will return to their default

state.

1. Press the [POWER] switch to power-on the ACD1.

2. Press the [POWER] switch again to turn off the power.

• The settings at the time you powered-off are remembered. When you turn on the power again, the unit will start up

with the same settings. You can use the “Last Mem. Resume” setting to set up the unit so that at startup it will recall

the scene number selected before you turned off the power to the device.

• Do not power-off the unit while its LCD indicates “Do not turn off!” Otherwise, a malfunction may occur.

•A small amount of current is ﬂowing even when the power switch is off. If you will not be using this device for an

extended period of time, be sure to disconnect the power plug from the AC outlet.

Connecting the AC power cable

Turning the power on and off

CAUTION

NOTE

CAUTION

ACD1 Owner’s Manual

Connection Examples

To construct an ampliﬁer control system, connect the ACD1 to your ampliﬁers and computer as follows.

Connections between the ACD1 and computer

• Use a network switch that is compatible with 100Base-TX/10Base-T.

• The network switch is not necessary if the computer and ACD1 are directly connected.

• The Ethernet cable between the computer or network switch and the ACD1 can be no longer than 100 meters. However,

due to variations in computers, network switches, and cable quality, proper operation at the maximum length cannot be

guaranteed in some cases.

• In the United States or Canada, the Ethernet cables that connect the ACD1 to the computer or network switch should be

STP cables in order to avoid electromagnetic interference.

• Since the ACD1 supports Auto MDI/MDI-X, it will automatically detect whether the connected cable is of the straight type

or crossover type, and will conﬁgure itself to create the appropriate connection. Therefore, you can use either a straight or

crossover cable.

Network switch

Ethernet cable

D-Sub cable

XP series

XM series

XH series

Tn series

PC-N series

Ethernet straight cable

TXn series

ACD1

Amp Editor

Maximum of 32 amps

Maximum of 8 amps

NOTE

ACD1 Owner’s Manual

Connection Examples

The ACD1 allows daisy-chain connection of up to 32 PC-N or Tn series units using Ethernet cable via the [DATA PORT] con-

nector.

Connection procedure

1. Make the appropriate AMP ID and terminator settings using the [AMP ID] switches located on the rear

panel of the connected ampliﬁers.

Specify a different AMP ID for each ampliﬁer that is connected to the same ACD1. The AMP ID will be the total of the

values of the switches that are set to ON.

Set the T (terminator) switch to ON for the last ampliﬁer in the daisy-chain.

2. Use Ethernet cables to daisy-chain the ACD1’s [DATA PORT] connector and the [DATA PORT] connector of

the ampliﬁers, as shown in the illustration.

It is not necessary to connect the ampliﬁers in order of their AMP ID, but connecting them in this order will make it easier

to determine the AMP ID without looking at the rear panel.

• The total maximum length of Ethernet cable that can be used is 500 meters.

• Use CAT5 or higher UTP straight Ethernet cable or STP straight Ethernet cable that connects all eight pins.

• Both PC-N series units and Tn series units can be connected to the same ACD1.

•You can make connections to either of the two [DATA PORT] connectors on the ampliﬁer.

Connections with the PC-N or Tn series

In the example shown in this illustration, the AMP ID

is 28 (16+8+4) and the terminator is ON.

AMP ID : 0

T : OFF

AMP ID : 1

T : OFF

AMP ID : 2

T : OFF

AMP ID : 31

(Maximum of

32 amps)

T : ON

DATA PORT connector

DATA PORT

ACD1

NOTE

ACD1 Owner’s Manual

Connection Examples

Up to eight XP, XM, or XH series units can be connected to the ACD1 via the [MONITOR/REMOTE] connectors.

Connection procedure

1. Connect the ACD1’s [MONITOR/REMOTE] connector to the [MONITOR/REMOTE] connector of the XP,

XM, or XH series unit using a D-Sub 15-pin cable (such as a commercially-available VGA cable for a com-

puter monitor) as shown below.

• Use a D-sub straight cable that has all ﬁfteen pins connected.

• The maximum D-sub cable length that can be used is 50 meters.

An Ethernet-compatible controller such as AMX or Crestron can be connected, allowing remote control of the ACD1 and the

ampliﬁers connected to the ACD1.

If you connect an Ethernet-compatible remote controller, you must set the ACD1 IP Port number by using [6.Network Setup]

→ [IP Ctrl Port #] on the ACD1 unit. Alternatively, in Amp Editor you can click the [Device Setup] menu command [IP Control

Port No.] and open the “IP Control Port No.” dialog box, and then specify the ACD1’s IP port number in the “External Device

Port” ﬁeld. For details of the remote control communication protocol, please refer to the TXn/ACD1 remote control protocol

speciﬁcation provided on the website.

http://www.yamahaproaudio.com/

Connections with the XP, XM, or XH series

Connections with controllers from other manufacturers

Maximum of

8 amps

MONITOR/

REMOTE

connector

MONITOR/REMOTE

connector

XP series

XM series

XH series

ACD1

AMP ID : 35

AMP ID : 34

AMP ID : 33

NOTE

ACD1 Owner’s Manual

Operations that can be performed from the panel

The following operations can be performed from the ACD1’s front panel.

•For details, refer to the ACD1 Reference Manual.

• Before use, remove the transparent protective ﬁlm that was applied to the LCD prior to shipment from the factory.

Category Sub category Operation performed

1. Scene Recall Recalls a scene on the speciﬁed ampliﬁer.

Store Saves a scene for the speciﬁed ampliﬁer.

2. Amp Control Standby/On Switches the power of the speciﬁed ampliﬁer between On and Standby.

Mute Mutes or unmutes the channel of the speciﬁed ampliﬁer.

Attenuation Adjusts the channel attenuator value of the speciﬁed ampliﬁer. (PC-N and Tn

series only)

3. Output Monitor Displays the output level of the speciﬁed ampliﬁer.

4. Device Setup Device ID Speciﬁes the ACD1’s Device ID address.

Device Label Displays the name of the ACD1 assigned by Amp Editor.

Identify Blinks the “Identify” icon of the corresponding ACD1 in Amp Editor.

5. Utility Battery Displays the state of the ACD1’s internal backup battery.

Firmware Ver. Displays the ACD1’s ﬁrmware version.

LCD Backlight Selects whether the ACD1’s LCD backlight will be always lit (ON) or lit only during

operation (Auto OFF).

Panel Operation Restricts panel operations of the ACD1.

Scene Recall Speciﬁes whether scene recall from the ACD1’s panel is enabled (Enable) or dis-

abled (Disable).

EMG Scene Setup Speciﬁes the scene number that will be recalled when the EMG (Emergency) sig-

nal is received from an external controller.

Last Mem. Resume Speciﬁes whether the ACD1 will start up with the settings that were in effect when

the power was last turned off (ON) or whether it will start up by recalling the amp’s

scene number that was in effect when the power was last turned off (OFF).

Clock Setup Sets the date and time of the ACD1’s internal clock.

GPI Calibration Calibrates the [GPI IN] connector input voltage.

6. Network Setup IP Address Mode Selects whether the ACD1’s IP address will be set automatically from Amp Editor

(DHCP) or set manually (Manual).

IP Address Speciﬁes the ACD1’s IP address.

MAC Address Displays the ACD1’s MAC address.

IP Ctrl Port # Speciﬁes the port number used when controlling the ACD1 via Ethernet from an

external controller such as AMX/Crestron.

NOTE

ACD1 Owner’s Manual

Troubleshooting

Initializing the internal memory

You can initialize the ACD1’s internal memory.

• The log data is preserved even if you execute initialization.

• When you initialize the internal memory, the content that had been saved in memory (scenes for each amp, and ACD1

settings) will be lost.

Use caution when performing the following steps.

1. Power-off the ACD1.

2. While holding down the [BACK] button, turn the power on.

3. Press the [▲INC/YES] button to initialize the internal memory.

When initialization is completed, the ACD1 will automatically restart.

• During initialization, the message “Do not turn off!” will be shown in the display.

Never power-off the ampliﬁer while this message is displayed.

Symptom Possible causes Response

All scene data saved in the

ACD1 has disappeared.

The power was turned off while the

ACD1’s data was being saved.

Synchronize with Amp Editor once again to transmit the set-

tings from Amp Editor.

The backup battery has run down. Check [5.Utility] → [Battery] for the state of the backup bat-

tery. If the state shows any message other than “OK,” ask

qualiﬁed Yamaha service personnel to replace the backup

battery.

An alert message is displayed. An incorrect or abnormal connec-

tion with the ampliﬁer or other alert

event related to the connections

has occurred.

For details on the meaning of each alert message and the

appropriate measures to take, refer to the Amp Editor

Owner’s Manual.

Panel operations are not

accepted.

The unit is locked. For details, refer to “5.Utility” in the ACD1 reference manual.

A scene can be saved but not

recalled.

“Scene Recall” is set to “Disable.” Access [5.Utility], then [SceneRecall] and set it to “Enable.”

The LCD is not backlit. “LCD Backlight” is set to “Auto

OFF.”

To set the unit so that the LCD remains backlit at all times,

access [5.Utility], then [LCD Backlight] and set it to “ON.”

NOTE

CAUTION

ACD1 Owner’s Manual

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accor-

dance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authori-

ties or dealer and ask for the correct method of disposal.

Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte

Beﬁndet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten

benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden.

In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC, bringen Sie alte Geräte bitte

zur fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen.

Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen und verhindern

mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgere-

chte Müllentsorgung auftreten könnten.

Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte, kontaktieren Sie bitte Ihre örtliche

Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel.

[Information für geschäftliche Anwender in der Europäischen Union]

Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Infor-

mationen.

[Entsorgungsinformation für Länder außerhalb der Europäischen Union]

Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontak-

tieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmeth-

ode.

Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques

Le symbole sur les produits, l’emballage et/ou les documents joints signiﬁe que les produits électriques ou électron-

iques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électron-

iques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et

aux Directives 2002/96/EC.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la

sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pour-

raient advenir lors d’un traitement inapproprié des déchets.

Pour plus d’informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électron-

iques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez

acheté les produits.

[Pour les professionnels dans l’Union Européenne]

Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre

vendeur ou fournisseur pour plus d’informations.

[Information sur le traitement dans d’autres pays en dehors de l’Union Européenne]

Ce symbole est seulement valables dans l’Union Européenne. Si vous souhaitez vous débarrasser de déchets

d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander

la méthode de traitement appropriée.

ACD1 Owner’s Manual

Información para Usuarios sobre Recolección

y Disposición de Equipamiento Viejo

Este símbolo en los productos, embalaje, y/o documentación que se acompañe signiﬁca que los productos electróni-

cos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes.

Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolec-

ción aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.

Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial

efecto negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los

desechos.

Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su

servicio de gestión de residuos o el punto de venta en el cual usted adquirió los artículos.

[Para usuarios de negocios en la Unión Europea]

Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para

mayor información.

[Información sobre la Disposición en otros países fuera de la Unión Europea]

Este símbolo sólo es válidos en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus

autoridades locales y pregunte por el método correcto de disposición.

Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura

Questo simbolo sui prodotti, sull’imballaggio, e/o sui documenti che li accompagnano signiﬁca che i prodotti elettriche

e elettroniche non dovrebbero essere mischiati con i riﬁuti domestici generici.

Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in

accordo con la Sua legislazione nazionale e le direttive 2002/96/CE.

Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti

negativi sulla salute umana e l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei riﬁuti.

Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comu-

nale locale, il Suo servizio di smaltimento dei riﬁuti o il punto vendita dove Lei ha acquistato gli articoli.

[Per utenti imprenditori dell’Unione europea]

Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori

informazioni.

[Informazioni sullo smaltimento negli altri Paesi al di fuori dell’Unione europea]

Questo simbolo è validi solamente nell’Unione europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue

autorità locali o il rivenditore e richieda la corretta modalità di smaltimento.

ACD1 Owner’s Manual

MEMO

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Olga Cossettini 1553, Piso 4 Norte

Madero Este-C1107CEK

Buenos Aires, Argentina

Tel: 011-4119-7000

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Europe GmbH

Branch Switzerland in Zürich

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Europe GmbH Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Europe GmbH

Branch Sp.z o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Europe Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Ofﬁce 4015, entrance 2, 21/5 Kuznetskii

Most street, Moscow, 107996, Russia

Tel: 495 626 0660

OTHER EUROPEAN COUNTRIES

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

TURKEY/CYPRUS

Yamaha Music Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu,

Shanghai, China

Tel: 021-6247-2211

INDIA

Yamaha Music India Pvt. Ltd.

5F Ambience Corporate Tower Ambience Mall Complex

Ambience Island, NH-8, Gurgaon-122001, Haryana, India

Tel: 0124-466-5551

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

4, 6, 15 and 16

ﬂoor, Siam Motors Building,

891/1 Rama 1 Road, Wangmai,

Pathumwan, Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou

au distributeur le plus proche de vous ﬁgurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten

Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen

Bestimmungsländern erhältlich.

Para detalles sobre productos, contacte su tienda Yamaha más cercana

o el distribuidor autorizado que se lista debajo.

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA24

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WM15360 909POCP?.?-02B0

Printed in Japan

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Yamaha ACD1 Omistajan opas

Merkki: Yamaha

Malli: ACD1

Luokka: Supplementary music equipment

Tyyppi: Omistajan opas

Lataa PDF

raportti

muilla kielillä

polski: Yamaha ACD1 Instrukcja obsługi
Türkçe: Yamaha ACD1 El kitabı
English: Yamaha ACD1 Owner's manual
čeština: Yamaha ACD1 Návod k obsluze
svenska: Yamaha ACD1 Bruksanvisning
русский: Yamaha ACD1 Инструкция по применению
italiano: Yamaha ACD1 Manuale del proprietario
Deutsch: Yamaha ACD1 Bedienungsanleitung
português: Yamaha ACD1 Manual do proprietário
dansk: Yamaha ACD1 Brugervejledning
français: Yamaha ACD1 Le manuel du propriétaire
español: Yamaha ACD1 El manual del propietario
Nederlands: Yamaha ACD1 de handleiding
română: Yamaha ACD1 Manualul proprietarului

Yamaha ACD1 Omistajan opas

Yamaha ACD1 Omistajan opas

muilla kielillä

Aiheeseen liittyviä papereita