Yamaha YST-M8 Ohjekirja

Kategoria
Soundbar speakers
Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

POWERED MULTIMEDIA SUBWOOFER
YST-MSW8
English
Français
POWERED MULTIMEDIA SUBWOOFER YST-MSW8
Active Servo
Technology
BASS
0
10
VOLUME
0
10
...............................1
.............................5
Active Servo
Technology
UCA
OWNER’S MANUAL / MODE D’EMPLOI
i
1
Read Instructions — All the safety and operating
instructions should be read before the unit is oper-
ated.
2
Retain Instructions — The safety and operating
instructions should be retained for future reference.
3
Heed Warnings — All warnings on the unit and in
the operating instructions should be adhered to.
4
Follow Instructions — All operating and other
instructions should be followed.
5
Water and Moisture — The unit should not be used
near water – for example, near a bathtub, wash-
bowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool, etc.
6
Carts and Stands — The unit should be used only
with a cart or stand that is recommended by the
manufacturer.
6A
An unit and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
unit and cart combination to over-
turn.
7
Wall or Ceiling Mounting — The unit should be
mounted to a wall or ceiling only as recommended
by the manufacturer.
8
Ventilation — The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be sit-
uated on a bed, sofa, rug, or similar surface, that
may block the ventilation openings; or placed in a
built-in installation, such as a bookcase or cabinet
that may impede the flow of air through the ventila-
tion openings.
9
Heat — The unit should be situated away from heat
sources such as radiators, stoves, or other appli-
ances that produce heat.
10
Power Sources — The unit should be connected to
a power supply only of the type described in the
operating instructions or as marked on the unit.
11
Power-Cord Protection — Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs, convenience receptacles, and the point
where they exit from the unit.
12
Cleaning — The unit should be cleaned only as rec-
ommended by the manufacturer.
13
Nonuse Periods — The power cord of the unit
should be unplugged from the outlet when left
unused for a long period of time.
14
Object and Liquid Entry — Care should be taken so
that objects do not fall into and liquids are not
spilled into the inside of unit.
15
Damage Requiring Service — The unit should be
serviced by qualified service personnel when:
A.
The power-supply cord or the plug has been
damaged; or
B.
Objects have fallen, or liquid has been spilled
into the unit; or
C.
The unit has been exposed to rain; or
D.
The unit does not appear to operate normally or
exhibits a marked change in performance; or
E.
The unit has been dropped, or the enclosure
damaged.
16
Servicing — The user should not attempt service
the unit beyond those means described in the oper-
ating instructions. All other servicing should be
referred to qualified service personnel.
17
Power Lines — An outdoor antenna should be
located away from power lines.
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
ii
18
Grounding or Polarization — Precautions should be
taken so that the grounding or polarization is not
defeated.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Associa-
tion’s Consumer Electronics Group want you to
get the most out of your equipment by playing it at
a safe level. One that lets the sound come
through loud and clear without annoying blaring
or distortion – and, most importantly, without
affecting your sensitive hearing.
Since hearing damage from loud
sounds is often undetectable until it
is too late, YAMAHA and the Elec-
tronic Industries Association’s Con-
sumer Electronics Group
recommend you to avoid prolonged
exposure from excessive volume levels.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC require-
ments. Modifications not expressly approved by Yamaha
may void your authority, granted by the FCC, to use the
product.
2. IMPORTANT:
When connecting this product to accesso-
ries and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used.
Follow all installation instructions. Failure to follow instruc-
tions could void your FCC authorization to use this product
in the USA.
3. NOTE:
This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your
use of this product in a residential environment will not result
in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the opera-
tion of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker of fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to dis-
tribute this type of product. If you can not locate the appro-
priate retailer, please contact Yamaha Corporation of
America, 6600 Orangethorpe Ave, Buena Park, CA 90620
The above statement apply ONLY to those products dis-
tributed by Yamaha Corporation of America or its subsid-
iaries.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
CANADIAN ICES-003.
POUR LES CONSOMMATEURS CANADIENS
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRO-
DUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST
CONFORME À LA NORME NMB-003 DU CANADA.
1
System Example / Exemple de connexion
Example 1
Example 2
English
1
Powered Main Speakers with Connecter for
Subwoofer
2
3.5 mm stereo mini-plug cable (not include)
3
3.5 mm stereo mini-plug cable (Accessories)
4
Personal computer
5
Portable CD player
6
Powered Main Speakers
Français
1
Enceintes actives principales avec borne pour
subwoofer
2
Câble avec fiches mini-jack stéréo 3,5 mm
(Pas fourni)
3
Câble avec fiches mini-jack stéréo 3,5 mm
(Accessoires)
4
Ordinateur individuel
5
Lecteur de CD portatif
6
Enceintes actives principales
5
4
1
2
3
or
TO
LEFT
SPEAKER
OUTPUT
(ADJ. VOL)
DC 12V
INPUT 2
INPUT 1
YST-MSW8
LINE IN
AUTO
STANDBY
LINE OUT
ABOVE 150Hz
ON OFF
LINE IN LINE OUT
ABOVE 150Hz
Active Servo
Technology
VOLUME
TONE
POWER
PRESENCE
VOLUME
YST-M10
POWERED MONITOR SPEAKER
Actve Servo
Technology
SER NO.
DC 14V
STEREO
INPUT
OUTPUT
to
To Left
Speaker
4
3
2
5
6
or
YST-MSW8
LINE IN
AUTO
STANDBY
LINE OUT
ABOVE 150Hz
ON OFF
LINE IN LINE OUT
ABOVE 150Hz
2
English
Thank you for purchasing Yamaha’s YST-MSW8 Powered Multimedia Subwoofer. Yamaha’s Active Servo Technol-
ogy offers exceptionally high performance.
Cautions
Please read the following operating precautions before
use:
When disconnecting the AC power cord from an AC
receptacle, hold and pull the plug, not the power cord.
If the YST-MSW8 is not going to be used for a while,
disconnect the AC power cord from the AC receptacle.
Always disconnect the AC power cord from the AC
receptacle before making any connections.
The YST-MSW8 does not contain any user serviceable
parts. Refer all servicing to your Yamaha dealer.
Never open the cabinet.
If a foreign object drops into
the set, contact your dealer, and do not use the
YST-MSW8. Otherwise, you may cause a fire.
Do not expose the YST-MSW8 to temperature extremes,
direct sunlight, excessive dust, humidity, or vibration.
Position the YST-MSW8 on a level, stable surface. Do
not drop the YST-MSW8, apply excessive force to
their controls, or put heavy items on top of them.
Since this unit has a built-in power amplifier, heat will
radiate from the rear panel. Therefore, place the unit
apart from the walls, allowing a space of at least 10 cm
(3-15/16") above, behind and on the both sides of the
unit. Also, do not position with the rear panel facing
down on the floor or other surface.
Do not obstruct the port with your hand or a foreign
object.
To protect the YST-MSW8 speaker, avoid microphone
feedback, continuous and excessive output from elec-
tronic musical instruments, and excessive signal dis-
tortion.
If the YST-MSW8 is located close to fluorescent or
neon lights, a slight hum may be heard. In this case,
relocate the YST-MSW8 away from the light.
Although the YST-MSW8 speaker is magnetically
shielded, keep floppy disks and tapes away from them.
The YST-MSW8 may cause picture distortion when
located close to a television or computer monitor. In
this case, move them away a short distance.
Avoid sources of hum (transformers, motors). To prevent
fire or electrical shock, do not expose to rain and water.
Do not use force on switches, knobs or cords. When
moving the YST-MSW8, first turn the YST-MSW8 off.
Always turn the volume control counterclockwise
before starting to play the audio source: increase the
volume gradually to an appropriate level after the play-
back has started.
Connections & Controls
Front Panel
Refer to the illustrations on page 1.
1
(power)
switch and indicator:
Press the
(power) switch to turn on the YST-MSW8; the power
indicator lights up. Press again to turn off. Turn down
the BASS and VOLUME controls before turning on
and off the YST-MSW8.
2
BASS control:
Use this control to adjust the volume
of the YST-MSW8. Turn it clockwise to increase the
volume; counterclockwise to decrease it.
3
VOLUME control:
Use this control to adjust the vol-
ume of the YST-MSW8 and other equipment con-
nected to the rear panel LINE OUT jack.
Rear Panel
4
LINE IN:
This 3.5 mm jack is used to input signals to
the YST-MSW8.
5
LINE OUT:
This jack is used to output the LINE IN
signal to the main speakers. The low frequencies of
the signal are cut before being output to the speakers.
This prevents small speakers from becoming over-
loaded.
6
AUTO STANDBY switch:
When the AUTO
STANDBY switch is in the ON position, and no input
signal is received after 5–10 minutes, the unit turns
into the standby mode automatically. (and the power
indicator dims*) When an input signal is received, the
unit is turned back on automatically. When the AUTO
STANDBY switch is in the OFF position, this AUTO
STANDBY on/off function doesn’t work.
*U.K. and Europe model only.
Note:
The unit may turn off automatically when the
input signal level is very low. If this does occur,
increase the output level from the source device and
reduce the YST-MSW8 VOLUME control accordingly.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode.
In this state, this unit is designed to consume a very
small quantity of power.
123
POWERED MULTIMEDIA SUBWOOFER YST-MSW8
Active Servo
Technology
BASS
0
10
VOLUME
0
10
LINE IN
AUTO
STANDBY
LINE OUT
ABOVE 150Hz
ON OFF
4 5 6
3
Troubleshooting
If the speakers fail to operate normally, check the following table. It lists common operation errors and simple measures
that you can take to correct problems. If a problem cannot be corrected, or the symptom is not listed, disconnect the AC
power cord and contact your authorized YAMAHA dealer or service center for help.
Volume Adjustment
If the YST-MSW8 is connected to an output jack for a sub-woofer on a powered main
speaker (such as the Yamaha YST-M15, YST-M8, etc.) as shown in System example 1 on
page 1, raise the VOLUME control of the YST-MSW8 to the maximum and set the
BASS control to the noon or one-o’clock position. Then, use the volume control of the
powered main speakers to adjust the overall volume.
If the powered main speakers are connected to the YST-MSW8’s LINE OUT jack as
shown in System example 2 on page 1, set the YST-MSW8’s BASS control to the noon
or one-o’clock position and raise the volume control of the powered main speakers to
the maximum. Then, use the YST-MSW8’s VOLUME control to adjust the overall
volume.
FAULT CAUSE CURE
No sound comes from
the speakers or sub-
woofer.
The AC power cord is not properly
plugged into the wall outlet.
Insert the AC power cord firmly into the wall out-
let.
The (power) switch is turned OFF. Turn ON the (power) switch (the indicator
lights).
Connections are faulty or incomplete. Make the connections again, firmly, or use a dif-
ferent cable.
The volume is set to minimum. Turn the subwoofer VOLUME control to the right
to increase the volume.
Turn the speaker VOLUME control to the right to
increase the volume.
The level of the signal being input is
too low.
Turn up the volume on the connected component.
Noise. Connections are faulty or incomplete. Make the connections again, firmly, or use a dif-
ferent cable.
Noise is heard when the
power is turned on.
The power cord of this unit connected
to another unit’s SWITCHED AC OUT-
LET.
Connect the power cord to an UNSWITCHED AC
OUTLET.
Make sure to use the (power) switch on this
unit to turn the power on and off.
Power is not supplied
even though the
(power) switch is ON.
The power plug is not securely con-
nected.
Connect it securely.
No sound. The volume is set to 0. Turn the VOLUME control to right.
Speaker cables are not connected
securely.
Connect them securely.
Sound level is too low. Speaker cables are connected incorrectly. Connect them correctly.
A source sound with few bass frequen-
cies is played.
Play a source sound with bass frequencies. Turn
the VOLUME control to right.
It is influenced by standing waves. Relocate the subwoofer or break up the parallel sur-
face by placing bookshelves etc. along the walls.
The AUTO STANDBY
function doesn’t work.
The (power) switch is turned off. Turn the (power) switch on.
The source input signal is too low. Raise the input signal level to appropriate level.
The AUTO STANDBY
function activates unin-
tentionally.
The source input signal is too low. Raise the input signal level to appropriate level.
Power is turned on acci-
dentally when the AUTO
STANDBY function is set
to ON.
The other equipment’s hum interrupts
(i.e. computer, digital device).
Relocate the YST-MSW8 or cable wiring. Other-
wise, do not use the AUTO STANDBY function.
BASS
0
10
VOLUME
0
10
BASS
0
10
VOLUME
0
10
4
Specifications
Type
................................. Active Servo Technology
Output power
................. 15 W (100 Hz, 4
at
T.H.D.=10%)
Input sensitivity
.............. 45 mV (100 Hz, 4
at 15 W)
Input impedance
............ 20 k
Frequency response
....... 40 to 250 Hz (–10 dB)
Speaker unit
................... 12 cm (5") cone, magnetic shield-
ing
Output impedance
......... 600
Output level
.................... 45mV (at 45mV Rated Input)
Power consumption
....... 20 W
Power supply
U.S.A. and Canada models.........AC 120 V, 60 Hz
Australia model ..........................AC 240 V, 50 Hz
U.K. and Europe models ........... AC 230 V, 50 Hz
General model ........................... AC 110/120/220/240 V,
50/60 Hz
Dimensions
(W
×
H
×
D)
148 (5-13/16")
× 283 (11-1/8") × 210 (8-1/4") mm
Weight............................. 4 kg (8 lbs. 13 oz.)
Finish
YST-MSW8 W .......................... Computer white
YST-MSW8 B ........................... Black
Accessories
3.5 mm stereo mini-plug cable (1.8m) × 1
* Specifications subject to change without notice.
Printed in China
IP
V287530
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Yamaha YST-M8 Ohjekirja

Kategoria
Soundbar speakers
Tyyppi
Ohjekirja
Tämä käsikirja sopii myös