Yamaha Studio Manager v.2 Asennusohje

Brändi: Yamaha

Malli: Studio Manager v.2

Kategoria: Software

Tyyppi: Asennusohje

Tämä käsikirja sopii myös

M7CL
V2

Studio Manager Version 2 Installation Guide 1

Studio Manager Version 2

Installation Guide

ATTENTION

PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("AGREEMENT") CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY

PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS

BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION ("YAMAHA").

BY DOWNLOADING, INSTALLING, COPYING, OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS

OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS

SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY DELETE THE

SOFTWARE.

1. GRANT OF LICENSE AND COPYRIGHT

Yamaha hereby grants you the right to use one copy of the software program(s) and data ("SOFTWARE") accompanying this Agreement. The

term SOFTWARE shall encompass any updates to the accompanying software and data. The SOFTWARE is owned by Yamaha and/or

Yamaha’s licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions. While you are entitled to claim ownership

of the data created with the use of SOFTWARE, the SOFTWARE will continue to be protected under relevant copyrights.

• You may use the SOFTWARE on a single computer.

• You may make one copy of the SOFTWARE in machine-readable form for backup purposes only, if the SOFTWARE is on media where

such backup copy is permitted. On the backup copy, you must reproduce Yamaha's copyright notice and any other proprietary legends

that were on the original copy of the SOFTWARE.

• You may permanently transfer to a third party all your rights in the SOFTWARE, provided that you do not retain any copies and the

recipient reads and agrees to the terms of this Agreement.

2. RESTRICTIONS

• You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE

by any method whatsoever.

• You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the

SOFTWARE.

• You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other

computers.

• You may not use the SOFTWARE to distribute illegal data or data that violates public policy.

• You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.

Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following

restrictions which you must observe.

• Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.

• Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners

in public without permission of the copyright owner.

• The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modiﬁed

without permission of the copyright owner.

3. TERMINATION

This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or

provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such

termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.

4. DISCLAIMER OF WARRANTY ON SOFTWARE

You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided

"AS IS" and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY

DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.

SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR

REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE

SOFTWARE WILL BE CORRECTED.

SOFTWARE LICENSE AGREEMENT

Studio Manager Version 2 Installation Guide 2

5. LIMITATION OF LIABILITY

YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT

SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF

THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha's total liability to you for all damages, losses and causes of action (whether in

contract, tort or otherwise) exceed the amount paid for the SOFTWARE.

6. THIRD PARTY SOFTWARE

Third party software and data ("THIRD PARTY SOFTWARE") may be attached to the SOFTWARE. If, in the written materials or the electronic data

accompanying the Software, Yamaha identiﬁes any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must

abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY

SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any

way for the THIRD PARTY SOFTWARE or your use thereof.

•Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL

IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.

•Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.

•Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or

consequential damages, expenses, lost proﬁts, lost data or other damages arising out of the use, misuse or inability to use the THIRD

PARTY SOFTWARE.

7. GENERAL

This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conﬂict of laws. Any dispute

or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction ﬁnds any portion of this

Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.

8. COMPLETE AGREEMENT

This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written

materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this

Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of

Yamaha.

• The software and this manual are the exclusive copyrights of Yamaha Corporation.

• Please read carefully the Software Licensing Agreement at the front of this manual before installing the application.

• Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of

the manufacturer.

•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for

the results of the use of this manual and the software.

• Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced at the following

website.

http://www.yamahasynth.com/download/ (Music Production)

http://www.yamahaproaudio.com/ (Professional Audio)

• The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the screens which

appear on your computer.

• The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may appear somewhat different

from those on your instrument.

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for

your personal use.

• Windows is the registered trademarks of Microsoft

Corporation.

• Apple and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Special Notices

Studio Manager Version 2 Installation Guide 3

Studio Manager is a cross-platform application that enables you to start multiple Editors that control YAMAHA

hardware products remotely, and to save multiple Editor settings.

You can run Studio Manager as a stand-alone application, or as a plug-in within DAW (digital audio workstation)/

sequencer applications that are compatible with Total Recall, such as Cubase SX 3.0.1 or later. In either case, the

basic functionality is the same. For the latest information on compatible DAW applications, refer to the following

website.

http://www.studioconnections.org/

The actual installation steps and the use of the software itself differs depending on the operating system that you

are using. Please refer to the appropriate installation instructions.

For subsequent operations, refer to the PDF manual from the [HELP] menu in each software program.

Precautions when using the USB TO HOST connector

When connecting the computer to the USB TO HOST connector, make sure to observe the following points. Failing to do so

risks freezing the computer and corrupting or even losing the data. If the computer or the instrument freezes, turn the power

to the instrument off or restart the computer.

• Before connecting the computer to the USB TO HOST connector, exit from any power-saving mode

(such as suspended, sleep, standby) of the computer.

• Before turning on the power to the instrument, connect the computer to the USB TO HOST connector.

• Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB

cable to/from the USB TO HOST connector.

- Quit any open applications.

- Make sure that data is not being transmitted from the instrument. (Data is transmitted only by playing

notes on the keyboard or playing back a song.)

• While a USB device is connected to the instrument, you should wait for six seconds or more between

these operations: (1) when turning the power of the instrument off then on again, or (2) when alternately

connecting/disconnecting the USB cable.

Studio Manager

Installing the Software

Procedures Windows Macintosh

Verify that your system meets the operating requirements of each software

program.

page 4 page 7

Install the appropriate driver to your computer. page 4 page 7

Install the Studio Manager and each editor. page 6 page 8

Start up the Studio Manager, then start up the editor.

Refer to the PDF manual and

installation guide for your

particular editor.

CAUTION

Studio Manager Version 2 Installation Guide 4

Minimum System Requirements

Make sure that the computer you are using satisﬁes the recommended system requirements for each editor

software. For details about the system requirements, refer to the owner’s manual for each editor.

n The system requirements may differ slightly depending on the particular operating system.

Windows Software Installation

To use the Studio Manager, you’ll need to install the following software programs. Follow the appropriate

instructions below corresponding to the software you’re using.

Driver Installation

Depending on the cable connection you are using, install the USB-MIDI driver or DME-N Network Driver or mLAN

Tools.

n You can also use MIDI cables to connect your Yamaha hardware to the computer. For details, refer to the owner's manual of your

particular MIDI interface.

• USB-MIDI Driver

To operate your Yamaha hardware from your computer via USB, you’ll need to install the USB-MIDI driver software.

The USB-MIDI driver is software that transfers MIDI data back and forth between your sequencer software and the

hardware via a USB cable.

For Windows Users

• USB-MIDI driver (when connecting via USB) , DME-N Network Driver (when connecting via Ethernet) or mLAN

Tools (when connecting via mLAN)

• Studio Manager

• Editor software for your particular hardware

You can download the latest version of the USB-MIDI driver at the following website. For speciﬁc installation instructions,

refer to the installation guide included in the downloaded ﬁle.

http://www

.global.yamaha.com/download/usb_midi/

MUSIC PRODUCTION SYNTHESIZER

Sequencer

USB cable

Driver

Computer

Yamaha hardware with a USB interface

Studio Manager Version 2 Installation Guide 5

• DME-N Network Driver

To operate your Yamaha hardware from your computer via Ethernet, you'll need to install the DME-N Network Driver

software.

DME-N Network Driver is software that transfers MIDI data back and forth between your computer and the

hardware via Ethernet cable.

You can download the latest version of DME-N Network Driver at the following website. For speciﬁc installation

instructions, refer to the installation guide included in the downloaded ﬁle.

http://www.yamahaproaudio.com/

• mLAN Tools

To operate your mLAN device from your computer via mLAN, you’ll need to install the mLAN Tools software.

Included with mLAN Tools are driver and applications software for transferring audio/MIDI data, and setting the

audio/MIDI connections between the computer and the mLAN devices via an mLAN cable.

You can download the latest version of mLAN Tools at the following website. For speciﬁc installation instructions, refer to the

installation guide included in the downloaded ﬁle.

http://www

.yamahasynth.com/download/

Ethernet cable

Yamaha hardware with an Ethernet interface

Computer

Editor

Ethernet cable

Hub

Crossover cable

Driver

mLAN Tools

MUSIC PRODUCTION SYNTHESIZER

Sequencer

IEEE1394 cable

Computer

mLAN device

Studio Manager Version 2 Installation Guide 6

Studio Manager Installation

Studio Manager is a cross-platform application that enables you to use multiple Editor programs for remotely

controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.

For speciﬁc instructions on using the software, refer to the PDF manual from the [HELP] menu in the Studio

Manager and each Editor.

Follow the instructions below to install the software programs.

1 Extract the data from the downloaded compressed ﬁle and open the “sm***w” folder.

“***” represents the version number.

2 Double-click “setup.exe.”

A setup dialog of Studio Manager is displayed.

3 Follow the on-screen instructions to install the software.

For speciﬁc instructions on using the software, refer to the PDF manual from the [HELP] menu in each program.

Editor Installation

Each Yamaha Editor is a software program designed to work with a speciﬁc Yamaha hardware product, letting you

edit settings for the product completely from a connected computer.

Follow the instructions below to install the software programs.

Uninstall (removing the installed application)

To remove the installed editors and Studio Manager:

Select [START] → [Control Panel] → [Add/Remove Programs] → [Install/Uninstall], then select the application to be

removed and click [Add/Remove…].

Follow the on-screen instructions to uninstall the application.

n The button names or menus may differ depending on the computer OS.

You can download the latest version editor for each hardware at the following website. For speciﬁc installation instructions,

refer to the installation guide included in the downloaded ﬁle.

http://www

.yamahasynth.com/download/ (Music Production)

http://www

.yamahaproaudio.com/ (Professional Audio)

Studio Manager Version 2 Installation Guide 7

Minimum System Requirements

Make sure that the computer you are using satisﬁes the recommended system requirements for each editor

software. For details about the system requirements, refer to the owner’s manual for each editor.

n The system requirements may differ slightly depending on the particular operating system.

Macintosh Software Installation

To use the Studio Manager, you’ll need to install the following software programs. Follow the appropriate

instructions below corresponding to the software you’re using.

Driver Installation

Depending on the cable connection you are using, install the USB-MIDI driver or mLAN Tools.

n You can also use MIDI cables to connect your Yamaha hardware to the computer. For details, refer to the owner’s manual of your

particular MIDI interface.

• USB-MIDI Driver

To operate your Yamaha hardware from your computer via USB, you’ll need to install the USB-MIDI driver software.

The USB-MIDI driver is software that transfers MIDI data back and forth between your sequencer software and the

hardware via a USB cable.

For Macintosh Users

• USB-MIDI driver (when connecting via USB) or mLAN Tools (when connecting via mLAN)

• Studio Manager

• Editor software for your particular hardware

You can download the latest version of the USB-MIDI driver at the following website. For speciﬁc installation instructions,

refer to the installation guide included in the downloaded ﬁle.

http://www

.global.yamaha.com/download/usb_midi/

MUSIC PRODUCTION SYNTHESIZER

Sequencer

USB cable

Driver

Computer

Yamaha hardware with a USB interface

Studio Manager Version 2 Installation Guide 8

• mLAN Tools

To operate your mLAN device from your computer via mLAN, you’ll need to install the mLAN Tools software.

Included with mLAN Tools are driver and applications software for transferring audio/MIDI data, and setting the

audio/MIDI connections between the computer and the mLAN devices via an mLAN cable.

n Depending on your OS version, the mLAN connection may not function properly. For details, refer to the installation guide included with

mLAN Tools.

Studio Manager Installation

Studio Manager is a cross-platform application that enables you to use multiple Editor programs for remotely

controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.

For speciﬁc instructions on using the software, refer to the PDF manual from the [HELP] menu in the Studio

Manager and each Editor.

1 Extract the data from the downloaded compressed ﬁle and open the “sm***mx” folder.

“***” represents the version number.

2 Double-click “Install Studio Manager.mpkg.”

A setup dialog of Studio Manager is displayed.

3 Follow the on-screen instructions to install the software.

Editor Installation

Each Yamaha Editor is a software program designed to work with a speciﬁc Yamaha hardware product, letting you

edit settings for the product completely from a connected computer.

Follow the instructions below to install the software programs.

You can download the latest version of mLAN Tools at the following website. For speciﬁc installation instructions, refer to the

installation guide included in the downloaded ﬁle.

http://www

.yamahasynth.com/download/

You can download the latest version editor for each hardware at the following website. For speciﬁc installation instructions,

refer to the installation guide included in the downloaded ﬁle.

http://www

.yamahasynth.com/download/ (Music Production)

http://www

.yamahaproaudio.com/ (Professional Audio)

mLAN Tools

MUSIC PRODUCTION SYNTHESIZER

Sequencer

IEEE1394 cable

Computer

mLAN device

Studio Manager Version 2 Installation Guide 9

Please refer to the installation guide and PDF manual for your particular editor, as well as the Studio Manager PDF

manual. You can open the PDF manuals for the editor and Studio Manager from the [HELP] menu.

When controlling the hardware from a computer via USB/Ethernet/mLAN, the hardware does not

operate correctly or no sound is heard.

•Have you installed the latest driver?...........................................................................Windows: page 4, Macintosh: page 7

• Is the USB/mLAN cable connected correctly?................................................ Owner’s manual for your particular hardware

• Is the Ethernet cable connected correctly?

Connect the computer to the hardware by using an Ethernet cable via a hub. When connecting the computer to the hardware

directly, use a crossover cable.

• Are the volume settings of the tone generator, playback device, and application program set to the appropriate

levels?................................................................................ Owner’s manuals for your particular hardware and DAW/sequencer

•Have you selected an appropriate ports in the hardware or DAW/sequence software?

............................................................................................ Owner’s manuals for your particular hardware and DAW/sequencer

• If your computer has automatically activated any power-saving mode (such as suspended, sleep, standby) when

using the USB connection, the computer may “freeze,” or the driver may stop working. When using USB, disable

any power-saving mode on the computer.

Playback response is delayed.

• Does your computer satisfy the system requirements?.....................................Installation Guide for your particular editor

• Is any other application or device driver running?

Getting Started (for both Windows/Macintosh)

Troubleshooting

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation