Yamaha DD-75 Omistajan opas

Kategoria
Music drums
Tyyppi
Omistajan opas
EN
Owners Manual
Before using the instrument, be sure to read “PRECAUTIONS” on page 5–6.
Digital Percussion
DD-75 Owner’s Manual
2
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply
(adapter). DO NOT connect this product to any power supply or
adapter other than one described in the manual, on the name
plate, or specifically recommended by Yamaha.
WARNING: Do not place this product in a position where any-
one could walk on, trip over, or roll anything over power or con-
necting cords of any kind. The use of an extension cord is not
recommended! If you must use an extension cord, the minimum
wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller
the AWG number, the larger the current handling capacity. For
longer extension cords, consult a local electrician.
This product should be used only with the components supplied
or; a cart, rack, or stand that is recommended by Yamaha. If a
cart, etc., is used, please observe all safety markings and instruc-
tions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct
at the time of printing. However, Yamaha reserves the right to
change or modify any of the specifications without notice or obli-
gation to update existing units.
This product, either alone or in combination with an amplifier and
headphones or speaker/s, may be capable of producing sound
levels that could cause permanent hearing loss. DO NOT operate
for long periods of time at a high volume level or at a level that is
uncomfortable. If you experience any hearing loss or ringing in the
ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
Some Yamaha products may have benches and / or accessory
mounting fixtures that are either supplied with the product or as
optional accessories. Some of these items are designed to be
dealer assembled or installed. Please make sure that benches
are stable and any optional fixtures (where applicable) are well
secured BEFORE using.
Benches supplied by Yamaha are designed for seating only. No
other uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge relating to
how a function or effect works (when the unit is operating as
designed) are not covered by the manufacturer’s warranty, and
are therefore the owners responsibility. Please study this manual
carefully and consult your dealer before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and
environmentally friendly. We sincerely believe that our products
and the production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the law, we
want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which
(if applicable) is soldered in place. The average life span of this
type of battery is approximately five years. When replacement
becomes necessary, contact a qualified service representative to
perform the replacement.
This product may also use “household” type batteries. Some of
these may be rechargeable. Make sure that the battery being
charged is a rechargeable type and that the charger is intended
for the battery being charged.
When installing batteries, never mix old batteries with new ones,
and never mix different types of batteries. Batteries MUST be
installed correctly. Mismatches or incorrect installation may result
in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all
batteries away from children. Dispose of used batteries promptly
and as regulated by the laws in your area. Note: Check with any
retailer of household type batteries in your area for battery dis-
posal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some
reason its useful life is considered to be at an end, please
observe all local, state, and federal regulations that relate to the
disposal of products that contain lead, batteries, plastics, etc. If
your dealer is unable to assist you, please contact Yamaha
directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The
model number, serial number, power requirements, etc., are
located on this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided below
and retain this manual as a permanent record of your purchase.
Model
Serial No.
Purchase Date
PLEASE KEEP THIS MANUAL
92-BP (bottom)
For DD-75
DD-75 Owner’s Manual
3
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha may void your author-
ity, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements pro-
vides a reasonable level of assurance that your use of this
product in a residential environment will not result in harmful
interference with other electronic devices. This equipment gen-
erates/uses radio frequencies and, if not installed and used
according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic
devices. Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If this product
is found to be the source of interference, which can be deter-
mined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected
by the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distribute
this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America, Elec-
tronic Service Division, 6600 Orangethorpe Ave, Buena Park,
CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
FCC INFORMATION (U.S.A.)
For AC adaptor and DD-75
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den
ar ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspændingen til dette apparat er IKKE afbrudt,
sålænge netledningen sidder i en stikkontakt, som er tændt — også
selvom der er slukket på apparatets afbryder.
VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko
laitetta verkosta.
(standby)
The model number, serial number, power requirements, etc., may be
found on or near the name plate, which is at the bottom of the unit.
You should note this serial number in the space provided below and
retain this manual as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
(bottom_en_01)
DD-75 Owner’s Manual
4
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the liter-
ature accompanying the product.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturers instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tri-
pod, bracket, or table specified by
the manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the
cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during
lightning storms or when unused for long periods of
time.
14 Refer all servicing to qualified service personnel. Ser-
vicing is required when the apparatus has been dam-
aged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has
been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
For AC adaptor
CAN ICES-3 (B)/NMB-3(B)
(can_b_02)
(fcc_sengen_C)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
DD-75 Owner’s Manual
5
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe and handy place for future reference.
For AC adaptor
WARNING
This AC adaptor is designed for use with only Yamaha electronic instruments. Do
not use for any other purpose.
Indoor use only. Do not use in any wet environments.
Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
CAUTION
When setting up, make sure that the AC outlet is easily accessible. If some
trouble or malfunction occurs, immediately turn off the power switch of the
instrument and disconnect the AC adaptor from the outlet. When the AC adaptor
is connected to the AC outlet, keep in mind that electricity is flowing at the
minimum level, even if the power switch is turned off. When you are not using
the instrument for a long time, make sure to unplug the power cord from the wall
AC outlet.
For DD-75
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or radiators. Also,
do not excessively bend or otherwise damage the cord, or place heavy objects on
it.
Only use the voltage specified as correct for the instrument. The required voltage
is printed on the name plate of the instrument.
Use the specified adaptor (page 54) only. Using the wrong adaptor can result in
damage to the instrument or overheating.
Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
This instrument contains no user-serviceable parts. Do not open the instrument
or attempt to disassemble or modify the internal components in any way. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place on it any containers (such as vases, bottles or glasses)
containing liquids which might spill into any openings. If any liquid such as
water seeps into the instrument, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the instrument inspected by qualified
Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit. A burning item may fall
over and cause a fire.
Follow the precautions below. Failure to do so might result in explosion, fire,
overheating or battery fluid leakage.
- Do not tamper with or disassemble batteries.
- Do not dispose of batteries in fire.
- Do not attempt to recharge batteries that are not designed to be charged.
- Keep the batteries separate from metallic objects such as necklaces, hairpins,
coins, and keys.
- Use the specified battery type (page 54) only.
- Use new batteries, all of which are the same type, same model, and made by
the same manufacturer.
- Always make sure all batteries are inserted in conformity with the +/- polarity
markings.
- When the batteries run out, or if the instrument is not to be used for a long
time, remove the batteries from the instrument.
- When using Ni-MH batteries, follow the instructions that came with the
batteries. Use only the specified charger device when charging.
Keep batteries away from small children who might accidentally swallow them.
If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid
should come in contact with your eyes, mouth, or skin, wash immediately with
water and consult a doctor. Battery fluid is corrosive and may possibly cause loss
of sight or chemical burns.
When one of the following problems occur, immediately turn off the power switch
and disconnect the electric plug from the outlet. (If you are using batteries,
remove all batteries from the instrument.) Then have the device inspected by
Yamaha service personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the instrument.
- There is a sudden loss of sound during use of the instrument.
Power supply/AC adaptor
Do not open
Water warning
Fire warning
Battery
If you notice any abnormality
DMI-5 1/2
DD-75 Owner’s Manual
6
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so
can result in lower sound quality, or possibly cause overheating in the outlet.
When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
Remove the electric plug from the outlet when the instrument is not to be used for
extended periods of time, or during electrical storms.
Do not place the instrument in an unstable position where it might accidentally
fall over.
Before moving the instrument, remove all connected cables, to prevent damage
to the cables or injury to anyone who might trip over them.
When setting up the product, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the power
switch and disconnect the plug from the outlet. Even when the power switch is
turned off, electricity is still flowing to the product at the minimum level. When
you are not using the product for a long time, make sure to unplug the power
cord from the wall AC outlet.
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components,
set all volume levels to minimum.
Be sure to set the volumes of all components at their minimum levels and
gradually raise the volume controls while playing the instrument to set the
desired listening level.
Do not insert a finger or hand in any gaps on the instrument.
Never insert or drop paper, metallic, or other objects into the gaps on the panel.
This could cause physical injury to you or others, damage to the instrument or
other property, or operational failure.
Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
Do not use the instrument/device or headphones for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
Always turn the power off when the instrument is not in use.
Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.
When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.
Make sure to discard used batteries according to local regulations.
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or
damage to other property, follow the notices below.
Handling
Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Otherwise, the instrument, TV, or radio may
generate noise. When you use the instrument along with an application on your
iPad, iPhone or iPod touch, we recommend that you set “Airplane Mode” to “ON”
on that device in order to avoid noise caused by communication.
Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration, damage to the internal components or
unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° –
104°F.)
Do not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or pads.
Maintenance
When cleaning the instrument, use a soft cloth. Do not use paint thinners,
solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.
Other cautions
The rubber parts of the pads include anti-deterioration agents and other
components to help maintain long-term quality. Depending on the storage or
operating environment, these components may appear on the surface as whitish
dust (blooming), but this has no effect on product performance and functions,
and the product can continue to be used with confidence. Also, stick marks may
be present on the pads, but these are the result of product inspection.
If you are bothered by blooming or stick marks, wipe the pads firmly with a dry,
soft cloth or a soft cloth that has been moistened with water and thoroughly
wrung out.
The rubber parts of the pads may become discolored due to changes over time,
but this has no effect on product performance and functions.
Saving data
The saved data may be lost due to some failure, an operation mistake, etc. Save
your important data onto an external device such as a computer (page 38).
Information
About copyrights
Copying of the commercially available musical data including but not limited to
MIDI data and/or audio data is strictly prohibited except for your personal use.
This product incorporates and bundles contents in which Yamaha owns copyrights
or with respect to which Yamaha has license to use others' copyrights. Due to
copyright laws and other relevant laws, you are NOT allowed to distribute media in
which these contents are saved or recorded and remain virtually the same or very
similar to those in the product.
* The contents described above include a computer program, Accompaniment
Style data, MIDI data, WAVE data, voice recording data, a score, score data, etc.
* You are allowed to distribute medium in which your performance or music
production using these contents is recorded, and the permission of Yamaha
Corporation is not required in such cases.
About this manual
The illustrations as shown in this manual are for instructional purposes only, and
may appear somewhat different from those on your instrument.
iPhone, iPad, iPod touch are trademarks of Apple Inc., registered in the U.S. and
other countries.
The company names and product names in this manual are the trademarks or
registered trademarks of their respective companies.
Power supply/AC adaptor
Location
Connections
Handling caution
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
DMI-5 2/2
DD-75 Owner’s Manual
7
Thank you for purchasing this Yamaha Digital Percussion!
We recommend that you read this manual carefully so that you can fully take advantage
of the advanced and convenient functions of the instrument. We also recommend that
you keep this manual in a safe and handy place for future reference.
About the Manuals
This instrument has the following documents and instructional materials.
Included Documents
Owner’s Manual (this book)
This document explains how to use the instrument.
Online Materials (downloadable from the Internet)
iPhone/iPad Connection Manual
Explains how to connect the instrument to smart devices, such as iPhone, iPad, etc.
Computer-related Operations
Includes instructions on connecting this instrument to a computer, and operations related to transferring song
data.
MIDI Reference
Contains MIDI-related information.
To obtain these manuals, access the Yamaha Downloads, and then the model name for searching the desired
files.
Included Accessories
• Owner’s Manual (this book)
• Drum stick (1 pair)
• Foot Pedal 1 & 2
• AC adaptor*
• Warranty*
• Online Member Product Registration
*: May not be included depending on your particular locale. Check with your Yamaha dealer.
Yamaha Downloads https://download.yamaha.com/
DD-75 Owner’s Manual
8
Main Features
Designed for comfortable playing
Each of the drum pads are angled and positioned on the panel for optimum playability and comfort. The
pads and pedal 1 can be adjusted independently over four levels, allowing for expressive drumming—not
only with the supplied sticks, but also for playing with your hands, by simply setting it to Hand Percussion
mode (page 18).
Realistic drum sound – Stereo Sampling
You can choose and play with 570 Voices, which provide for a variety of percussion sounds, from realistic
drum sounds (created with Stereo Sampling) to ethnic percussion sound of Japanese drum, Asia, Latin
America and beyond.
75 Drum kits
The instrument contains 75 drum kits of different genres for you to choose from. Moreover, the Voices
can be assigned to each drum pads and pedals to create your own original drum kits.
105 Songs
The instrument features 22 Songs including the Demos, and 83 Patterns that cover a wide variety of
music genres. You can play along with the full playback, or mute tracks and play the missing parts.
AUX IN Jack
This jack is for connection to an external audio source, letting you play the instrument with music and
accompaniment.
Compatible Formats and Functions
GM System Level 1
“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-com-
patible music data can be accurately played by any GM-compatible tone generator, regard-
less of manufacturer. The GM mark is affixed to all software and hardware products that
support GM System Level.
XGlite
As its name implies, “XGlite” is a simplified version of Yamaha’s high-quality XG tone gener-
ation format. Naturally, you can play back any XG song data using an XGlite tone generator.
However, keep in mind that some songs may play back differently compared to the original
data, due to the reduced set of control parameters and effects.
DD-75 Owner’s Manual
9
Contents
PRECAUTIONS .............................................. 5
NOTICE .......................................................... 6
Information ...................................................... 6
About the Manuals .......................................... 7
Included Accessories ...................................... 7
Main Features ................................. 8
Panel Controls ............................. 10
Setting Up ..................................... 12
Power Requirements .................................... 12
Connecting Pedals 1 and 2 ........................... 13
Turning the Power On/Off ............................. 13
Setting the Battery Type ............................... 13
Adjusting the Master Volume ........................ 14
Setting the Auto Power Off function .............. 14
Setting the Master EQ Type ......................... 14
Connecting Headphones or
External Speaker ..................................... 14
Using a Snare Drum Stand ........................... 15
Playing the Demo Song ............... 16
Play the Pads/Pedals ................... 17
Pad Names ................................................... 17
Setting the Hand Percussion ON/OFF .......... 18
Hand Percussion Lock .................................. 18
Selecting and Playing a Drum Kit ................. 19
Assigning Voices to Individual Pads and Pedals
and Saving to a Custom Kit (“
C01
”–“
C10
”)
... 20
Setting the Reverb type ................................ 21
Setting the Pad Sensitivity ............................ 22
Setting the Click ON/OFF ............................. 25
Click Settings ................................................ 25
Playing a Song ............................. 28
Selecting and Playing a Song ....................... 28
Tap Start ....................................................... 29
Pad Start ....................................................... 30
Setting the Auto Kit Select ON/OFF ............. 31
Adjusting the Tempo ..................................... 32
Play along with a Song ................ 33
Setting the Track ON/OFF ............................ 33
Break ............................................................ 33
Using A-B Repeat ......................................... 34
Recording a Song ........................ 35
Recording ..................................................... 35
Playing the recorded song ............................ 36
Song Clear .................................................... 37
Connecting to External Devices
... 38
Connecting to External MIDI Devices ........... 38
Connecting to a Computer ............................ 38
Playing an External Audio Device
with the Built-in Speakers ....................... 39
The Functions ............................... 40
Backup and Initialization ............. 41
Troubleshooting ........................... 42
Drum Voice List ............................ 43
Song List ....................................... 47
Drum Kit List ................................. 48
Drum Score ................................... 52
Specifications ............................... 54
Index .............................................. 55
Setting Up
Basic Operations
Appendix
DD-75 Owner’s Manual
10
Panel Controls
q MASTER VOLUME control.............................14
w Dial ..................................................................13
e KIT ASSIGN button.........................................20
r SENSITIVITY button .......................................22
t HAND PERC. button.......................................18
y KIT button ....................................................... 19
u CLICK button ..................................................25
i SONG button ..................................................28
o TEMPO/TAP button ........................................29
!0
PART MUTE DRUM 1–3, BACKING buttons
.....33
!1 FUNCTION button ..........................................40
!2 DEMO button .................................................. 16
!3 [ ] (Standby/On) switch............................... 13
!4 REC button ..................................................... 35
!5 BREAK button ................................................33
!6 A-B REPEAT button .......................................34
!7 START/STOP button....................................... 28
!8 Display ............................................................ 13
!9 Drum pads (8)................................................. 17
Front Panel
Front Panel
Indicates the song number when power is turned on.
Panel Controls
DD-75 Owner’s Manual
11
@0 DC IN 12V (AC Adaptor) jack.........................12
@1 AUX IN jack .....................................................39
@2 PHONES/OUTPUT jack ..................................14
@3 PEDAL 2 • HI-HAT jack................................... 13
@4 PEDAL 1 • KICK jack...................................... 13
@5 MIDI IN/OUT terminals ................................... 38
@0@1@2@3@4@5
Rear Panel
Drum Sticks
• Use the sticks with caution. Do not use
them for anything other than playing the
instrument. Also, to avoid damage or injury,
refrain from waving them recklessly or
throwing them.
• Since speakers are built into this instru-
ment, you should be careful to never leave
any watches, credit cards or any kind of
magnetic storage media on the panel—
doing so may result in data loss or damage
to the items. Also avoid using this instru-
ment near a television or computer moni-
tor, since interference may result.
CAUTION
NOTICE
Pedal 2Pedal 1
Rear Panel
DD-75 Owner’s Manual
12
Setting Up
Be sure to do the following operations BEFORE turning on the power.
Power Requirements
Although the instrument will run either from an AC adaptor
or batteries, Yamaha recommends use of an AC adaptor
whenever possible. An AC adaptor is more environmen-
tally friendly than batteries and does not deplete
resources.
Using an AC Adaptor
Make sure that the [ ] (Standby/On) switch is off, then
connect the AC adaptor in the order shown in the illustra-
tion.
Using Batteries
This instrument requires C size, Alkaline (LR14)/Manga-
nese (R14) batteries, or rechargeable nickel-metal hydride
batteries (rechargeable Ni-MH batteries). The Alkaline bat-
teries or rechargeable Ni-MH batteries are recommended
for this instrument, since other types may result in poorer
battery performance.
1 Make sure that the power of the instrument is off.
2 Open the battery compartment cover located on
the instrument’s bottom panel.
3 Insert the six new batteries, being careful to follow
the polarity markings on the inside of the compart-
ment.
4 Replace the compartment cover, making sure that
it locks firmly in place.
• Use only the specified AC adaptor (page 54). Using the
wrong AC adaptor can result in damage to the instrument
or overheating.
• When using the AC adaptor with a removable plug, make
sure to keep the plug attached to the AC adaptor. Using the
plug alone can cause electric shock or fire.
• Never touch the metallic section when attaching the plug.
To avoid electric shock, short circuit or damage, also be
careful that there is no dust between the AC adaptor and
plug.
• When setting up the product, make sure that the AC outlet
you are using is easily accessible. If some trouble or mal-
function occurs, immediately turn the power off and dis-
connect the plug from the outlet.
• Follow the order shown above in reverse when disconnecting
the AC adaptor/power cord.
AC outlet
AC
adaptor
2
1
DC IN jack
(page 11)
WARNING
Plug
Slide the plug as indicated.
The shape of the plug differs
depending on your area.
CAUTION
NOTE
• Connecting or disconnecting the power adaptor with bat-
teries installed may turn the power off, resulting in loss of
data being recorded or transferred at the time.
• Make sure to set the battery type correctly (page 13).
When battery power becomes too low for proper operation,
the volume may be reduced, the sound may be distorted,
and other problems may occur. When this happens, make
sure to replace all batteries with new ones or already
recharged ones.
• This instrument cannot charge the batteries. Use only an
appropriate charger device when charging.
• Power will be automatically drawn from the AC adaptor if an
AC adaptor is connected while batteries are installed in the
instrument.
NOTICE
NOTE
Setting Up
Setting Up
DD-75 Owner’s Manual
13
Connecting Pedals 1 and 2
Connect the supplied Pedal 1 to the [PEDAL 1 (KICK)] jack
and Pedal 2 to the [PEDAL 2 (HI-HAT)] jack.
Turning the Power On/Off
1
Turn down the [MASTER VOLUME] dial to “MIN.
2 Press the [ ] (Standby/On) switch to turn the
power on.
The display lights up. Adjust the volume as desired
while striking the pads.
3 Press and hold the [ ] (Standby/On) switch
for about a second to turn the power off.
Setting the Battery Type
Depending on the battery type to be used, you may need
to change the battery type setting on this instrument. To
change the setting, first turn on the power to the instru-
ment, then choose the battery type you would like to use.
Alkaline (and manganese) batteries are chosen by default.
1 Press the [FUNCTION] button.
Press the [DRUM 3] or [FUNCTION] button a number of
times until the “btt” item appears. The currently
selected battery type appears next to the “btt” indica-
tion.
2 Change the battery type by turning the dial.
To select Ni-MH, turn the dial to the right (clockwise)
until the “n-H” item appears, and to select Alkaline/
Manganese, turn the dial to the left (counter-clockwise)
until the “ALn” item appears.
3
Press the [FUNCTION] button to exit.
• Avoid getting caught in or tripping over the pedal cords;
this may cause the instrument to fall and result in damage
or injury.
• Avoid using the pedals directly on a soft floor, since they
may scratch the surface of the floor.
• Make sure that the pedal plugs are properly connected to the
PEDAL jacks before turning on the power.
• Do not press the pedals while turning the power on. Doing
this changes the recognized polarity of the pedal, resulting in
reversed pedal operation.
You can use an Electronic drum pad KP65 (sold separately) or
an Electronic kick unit KU100 (sold separately) and hi-hat con-
troller HH65 or HH40 (sold separately) plugging into the
[PEDAL 1 (KICK)] jack and [PEDAL 2(HI-HAT)].
Pedal 1 Pedal 2
CAUTION
NOTICE
When the power is turned on, Drum Kit number will
appear after the “dd” item appears. Drum Kit num-
ber “1” is normally selected.
• Even when the power switch is turned off, electricity is still
flowing to the product at the minimum level. When you are
not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
• Do not attempt any other operations, such as pressing but-
tons or the pedal. Doing so may cause the instrument to
malfunction.
• Do not turn off the power while saving data (a “-” mark
appears and moves from left to right on the display). Doing
so can result in loss of data.
• Failure to set the appropriate battery type may shorten the
battery life. Make sure to set the battery type correctly.
CAUTION
NOTICE
NOTICE
Setting Up
DD-75 Owner’s Manual
14
Adjusting the Master Volume
To adjust the volume of the entire pad/pedal sound, use
the [MASTER VOLUME] dial while striking the pads or
pressing the pedals.
Setting the Auto Power Off function
To prevent unnecessary power consumption, this instru-
ment features an Auto Power Off function that automati-
cally turns the power off if the instrument is not operated
for a specified period of time. The amount of time that
elapses before the power is automatically turned off is 30
minutes by default; however, you can change the setting
as desired (page 40).
Disabling Auto Power Off (simple method)
While holding down the [SONG] button, press the [ ]
(Standby/On) switch to turn the instrument on. The PoF
item appears after the “dd” to indicate the Auto Power Off
function has been disabled.
Setting the Master EQ Type
Master equalizer (EQ) settings give you the best possible
sound when listening through different reproduction sys-
tems—the instrument’s internal speakers, headphones, or
an external speaker system.
1 Enter the master EQ type setting function.
Press the [FUNCTION] button once, then press the
[DRUM 3] or [BACKING] button a number of times until
the “Eqt” item appears.
After a while, the current master EQ type appears next
to the “Eqt” indiction.
2 Select the desired master EQ type.
Turn the dial clockwise to set to “HP” (Headphone), and
turn it counter-clockwise to set to “SP” (Speaker).
3 Press the [FUNCTION] button to exit from the
Function mode.
Connecting Headphones or
External Speaker
Connect a pair of headphones to the [PHONES/OUTPUT]
jack. This jack also functions as an external output. By
connecting to a computer, recorder, or other audio device,
you can output the audio signal of this instrument to that
external device. The speakers of this instrument are auto-
matically shut off when a plug is inserted into this jack. You
may also want to change the master EQ type setting to
enjoy the optimum sound for either way of listening.
• Do not use the instrument for a long period of time at a
high or uncomfortable volume level, since this can cause
permanent hearing loss.
CAUTION
Do not use the instrument/device or headphones for a long
period of time at a high or uncomfortable volume level,
since this can cause permanent hearing loss.
• Before connecting the instrument to other electronic com-
ponents, turn off the power of all the components. Also,
before turning any components on or off, make sure to set
all volume levels to minimum. Otherwise, damage to the
components or electrical shock may occur.
• To avoid possible damage to the external device, first turn on
the power to the instrument, then to the external device. When
turning off the power, do so in reverse order: first turn off the
power to the external device, then to the instrument.
Display Master EQ type
HP for headphones or external speakers
SP
(Default)
for internal speakers
Standard stereo
phone plug
CAUTION
NOTICE
Setting Up
DD-75 Owner’s Manual
15
Using a Snare Drum Stand
This instrument can be installed on a snare drum stand (sold separately)
for convenience and ease in playing.
Snare drum stand (sold separately): SS662, SS740A
Setting Up
Open the legs wide enough so that the snare drum stand is stable, but
not so much that the pipe touches the floor. Tighten the wing nut E.
As shown in the illustration, make sure to always position the snare
drum stand so that one of the legs extends toward the player.
Use wing nut D to adjust the height, and turn B so that it faces the
player.
Use wing nut C to adjust the angle of B so that the instrument is
installed horizontally.
Use rotary nut A to loosen the three arm basket to fit the three inden-
tations on the bottom of the instrument.
Make sure all the nuts are securely tightened.
To install the snare drum stand
Put the arm covers into the indentations on the bottom of the instrument,
and tighten rotary nut A until the arms are secured. Make sure all the
nuts are securely tightened.
Be sure to handle the snare drum stand with care. Follow the important
precautions below. If not, the snare drum stand may overturn, causing the
instrument to drop and damage, possibly resulting in personal injury.
• Always place the snare drum stand on a flat, stable surface.
• Do not apply excessive force to the instrument.
• Do not adjust the height of snare drum stand with the instrument
installed.
• Remove the snare drum stand from the instrument before moving the
instrument.
• Do not use the snare drum stand other than designated ones (page 54).
A
C
Arms
Pipe
Legs
Snare drum stand
Player
B: Faces the player
Keep horizontal
D
E
B
CAUTION
DD-75 Owner’s Manual
16
Playing the Demo Song
This instrument features several demonstration songs (“001”–“005”), specially created
to show you the dynamic possibilities of the instrument.
1 Start the Demo Song.
2 Select a Demo Song.
3 Stop the Demo Song.
Press the [DEMO] button and the demo song starts playing.
• With the Auto Kit Select feature turned on, the best suited Drum Kit for the song will
automatically be selected. (See the “Setting the Auto Kit Select ON/OFF” on
page 31.)
Use the dial to select a demo song (“001”–“005”).
To stop playback, press the [DEMO] button again or press the
[START/STOP] button.
NOTE
Basic Operations
DD-75 Owner’s Manual
17
Play the Pads/Pedals
Strike the pad with the supplied drum sticks or your hands to play the drum voices.
When playing the pads with your hands, turn the Hand Percussion feature on by press-
ing the [HAND PERC.] button (the lamp lights).
The sound volume of the pads responds to your playing; when you play soft the vol-
ume is soft, and when you play strongly the volume is loud.
Pad Names
A hi-hat sound is assigned to Pad 6 (Drum Kit 1). Striking
Pad 6 while pressing Pedal 2 produces a closed hi-hat
sound.
Striking Pad 2 without pressing the pedal produces an
open hi-hat sound. Pressing Pedal 2 produces a hi-hit
pedal sound.
Press Pedal 2 to control the Hihat.
(This is in the case of Drum Kit 1; for other
kits, this may control a different sound.)
• When using Pedal 2, touch response
does not function.
NOTE
Pedal 1 features touch response; the volume
responds to how hard you press the pedal.
• If your pressing of the pedal is too slow
or soft, there may be no sound.
NOTE
Pedal 2
180: Hi-Hat Pedal Bright
Pedal 1
3: Maple Bass Drum 3
Pad 1
40: Maple Snare
Open Rim
Pad 4
105: Maple Tom 2
Pad 3
103: Maple Tom 4
Pad 2
102: Maple Tom 5
Pad 6
179: Hi-Hat
Closed
Bright
Pad 5
211: Crash
Cymbal Dark
Pad 8
208:
Ride
Cymbal
Warm 1
Pad 7
210:
Ride
Cymbal Cup
Warm
Ex. shown, Drum Kit 1
Play the Pads/Pedals
DD-75 Owner’s Manual
18
You can play the pads of the instrument either with the supplied sticks or with your hands. Press and set the fol-
lowing button when you play the instrument with your hands.
1 Press the [HAND PERC.] button.
If you perform on the instrument solely with your hands, we recommend that you use this operation to lock the
Hand Percussion so that it is always on. This protects the instrument from being inadvertently changed during
your performance.
1 Make sure that Hand Percussion is set to on (the lamp
is lit).
2 Set the Hand Percussion Lock to ON.
3 To turn off Hand Percussion Lock, press and hold the
[HAND PERC.] button until the “
LoC” is no longer
shown on the display.
Setting the Hand Percussion ON/OFF
When you press the [HAND PERC.] button, the buttons lamp lights,
and the pad sensitivity is automatically adjusted for optimum playing
by hand. At the same time, an appropriate song (057) and drum kit
(51) are automatically called up.
• Be sure to strike the pads only with your hands when HAND PERCUSSION is on.
Hand Percussion Lock
Press and hold the [HAND PERC.] button until “LoC” appears on the
display.
Lit
NOTE
Press and hold
Lit
Play the Pads/Pedals
DD-75 Owner’s Manual
19
The instrument allows you to choose from 75 different Drum Kits, which are preset voice combinations set to the
the eight pads and two pedals. (See “Drum Kit List” on page 48.)
The instrument also has ten Custom Drum Kits allowing you to assign the desired voices to the pads or pedals.
(See “Assigning Voices to Individual Pads and Pedals and Saving to a Custom Kit (“C01”–“C10”)” on page 20.)
1 Press the [KIT] button.
2 Select a Drum Kit Number.
Selecting and Playing a Drum Kit
When you press the [KIT] button, the currently selected Drum Kit
number appears on the display.
Turn the dial to select a Drum Kit number. Drum Kit numbers will
increase as the dial is turned to the right (clockwise), and decrease as
the dial is turned to the left (counter-clockwise).
• Drum Kit number “1” is normally selected when the power is turned on.
• Drum Kits “C01”–“C10” are Custom Kits.
* Custom Kits are those that you’ve assigned the desired voices to each pad and
pedal, then saved the entire assignments as a Kit. The initial settings of “C01”–
C10” are Drum Kit number 1. (See “Assigning Voices to Individual Pads and
Pedals and Saving to a Custom Kit (“C01”–“C10”)” on page 20.)
NOTE
Play the Pads/Pedals
DD-75 Owner’s Manual
20
Drum Kit Voices can be changed and saved as a Custom Kit “C01”–“C10.” The instrument contains a total of
570 high quality drum sounds plus 30 drum phrases (see the “Drum Voice List” on page 43)—and you can
assign these freely to each of the 8 drum pads and 2 pedals. To call up the saved Custom Kit, press the [KIT]
button and use the dial to select a Custom Kit number.
1 Select a Drum Kit (“1”–“75”) you desired to change,
then press the [KIT ASSIGN] button.
2 Turn the dial and select a Custom Kit “C01”–“C10” for
saving.
3 Select a pad or pedal to be assigned.
4 Select a Voice Number.
Repeat the previous steps 3 and 4 for any or all of the pads and pedals.
Assigning Voices to Individual Pads and Pedals and Saving to a Custom Kit
(“
C01
”–“
C10
”)
When you press the [KIT ASSIGN] button, the buttons lamp lights,
and “C01” appears on the display.
Strike any pad one time (or press a pedal), and the voice number of
currently assigned Drum Kit is shown in the display.
You can select the voice by repeatedly striking the pad or repeatedly-
pressing the pedal (while listening to the voice), or by turning the dial.
Striking the pad or pressing the pedal to select a voice.
Every time the pad is struck or a pedal is pressed, voice numbers will
increase by a value of one (1). In this method, you can hear and
select an assigned voice.
Using the dial to select a voice.
Turn the dial to the right (clockwise), and voice numbers will increase.
Turn the dial to the left (counter-clockwise), and voice numbers will
decrease.
To cancel, simply press the [KIT] button.
See the “Drum Voice List” on page 43.
Lit
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Yamaha DD-75 Omistajan opas

Kategoria
Music drums
Tyyppi
Omistajan opas