Yamaha YST-MSW10 Ohjekirja

Yamaha
Brändi
Yamaha
Malli
YST-MSW10
Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

ACTIVE SERVO PROCESSING
SUBWOOFER SYSTEM YST-MSW10
Active Servo
Technology
POWER
HIGH CUT
VOLUME
HIGH
LOW
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
SUBWOOFER SYSTEM
YST-MSW10
Active Servo
Technology
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NPT OPEN
• Explanation of Graphical Symbols
The lightning flash with the arrowhead symbol
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral tri-
angle is intended to alert you to the presence of
important operating and maintenance (servic-
ing) instructions in the literature accompanying
the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating instructions
should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the operating
instructions should be adhered to.
4 Follow Instructions – All operating and other instructions should
be followed.
5 Water and Moisture – The unit should not be used near water –
for example, near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, or near a swimming pool, etc.
6 Carts and Stands – The unit should be used only
with a cart or stand that is recommended by the
manufacturer.
6A A unit and cart combination should be moved with
care. Quick stops, excessive force, and uneven
surfaces may cause the unit and cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to a
wall or ceiling only as recommended by the manufacturer.
8
Ventilation – The unit should be situated so that its location or
position does not interfere with its proper ventilation. For
example, the unit should not be situated on a bed, sofa, rug, or
similar surface, that may block the ventilation openings; or
placed in a built-in installation, such as a bookcase or cabinet
that may impede the flow of air through the ventilation openings.
9
Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating instructions
or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the unit.
12 Cleaning – The unit should be cleaned only as recommended
by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long period of
time.
14 Object and Liquid Entry – Care should be taken so that objects
do not fall into and liquids are not spilled into the inside of the
unit.
15 Damage Requiring Service – The unit should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the unit;
or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16
Servicing – The user should not attempt to service the unit
beyond those means described in the operating instructions. All
other servicing should be referred to qualified service personnel.
17 Power Lines – An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization – Precautions should be taken so
that the grounding or polarization is not defeated.
i
System Example / Ejemplo del sistema
1
1
INPUT
2
TO LEFT
SPEAKER
OUTPUT
(ADJ. VOL)
DC 9V
POWER
PRESENCE
VOLUME
Actve Servo
Technology
POWER
PRESENCE
VOLUME
YST-M10
POWERED MONITOR SPEAKER
Actve Servo
Technology
YST-M10 Speaker System
with Built-in Amp.
SER NO.
DC 14V
STEREO
INPUT
OUTPUT
to
To Left
Speaker
Speaker System with
Connecter for Subwoofer
YST-MSW10
ACTIVE SERVO PROCESSING
SUBWOOFER SYSTEM YST-MSW10
Actve Servo
Technology
POWER
HIGH CUT
VOLUME
HIGH
LOW
IN
OUT
LINE 1
YST-MSW10
ACTIVE SERVO PROCESSING
SUBWOOFER SYSTEM YST-MSW10
Actve Servo
Technology
POWER
HIGH CUT
VOLUME
HIGH
LOW
IN
OUT
LINE 1
or
Portable CD Player
Personal Computer
or
Portable CD Player
Personal Computer
Front Panel & Rear Panel / Panel delantero y Panel trasero
2
1
2
3
4
5
6
ACTIVE SERVO PROCESSING
SUBWOOFER SYSTEM YST-MSW10
Active Servo
Technology
POWER
HIGH CUT
VOLUME
HIGH
LOW
IN
OUT
LINE 1
LINE 2
V844750-1 UC
MADE IN MALAYSIA
L
R
Thank you for purchasing a Yamaha YST-MSW10 Subwoofer System. Yamaha’s Active Servo Technology offers
exceptional high performance.
Cautions
Please read the following operating precautions before use:
• When disconnecting the power cord from an AC receptacle, hold
and pull the plug, not the cord.
• If the YST-MSW10 is not going to be used for a while, disconnect
it from the AC receptacle.
• Since this unit has a built-in power amplifier, heat will radiate from
the rear panel. Therefore, place the unit at least 10 cm (4 inches)
away from the wall. Also, do not position with the rear panel
facing down on the floor or other surface.
• Always disconnect from the AC receptacle before making any
connections.
• YST-MSW10 does not contain any user serviceable parts. Refer all
servicing to your Yamaha dealer.
• Do not expose the YST-MSW10 to temperature extremes, direct
sunlight, excessive dust, humidity, or vibration.
• Site the YST-MSW10 on a level, stable surface. Do not drop the
YST-MSW10, apply excessive force to its controls, or put heavy
items on top of it.
• If the YST-MSW10 should require cleaning, use a soft cloth. If
necessary, a damp cloth.
• Do not to put some objects into it. If doing so, the sound will be
unnatural or it may cause damage to the speaker and/or amplifier.
• To protect the YST-MSW10 speaker, avoid microphone feedback,
continuous and excessive output from electronic musical
instruments, excessive signal distortion,
3
Connections
Refer to page 1 for system connections.
Rear Panel (Refer to page 2)
1 LINE 1 IN: This 3.5 mm stereo jack connection is for inputting
line-level signals to the YST-MSW10.
2 LINE 1 OUT: This connection can be used to feed the input signal
to other equipment.
3 LINE 2: These RCA-pin jacks are for inputting speaker level
signals to the YST-MSW10. They can be connected directly to the
speaker outputs of a stereo amplifier.
• Although the YST-MSW10 is magnetically shielded, keep floppy
disks and tapes away from it.
• The YST-MSW10 may cause picture distortion when sited close to
a television or computer monitor. In this case, move it away a little.
English
Specifications
Type Active Servo Processing Subwoofer
System
Amplifier output 25 W/4 Ω (THD 10%, 100 Hz)
High-Cut Filter Low, High
Pressure Level 98 dB (max.)
Capacity 8.0 l
Frequency response 35 to 250 Hz (–10dB)
Speaker unit 6.3" (16 cm) cone woofer, magnetic
shielding
Power supply AC 120 V, 60 Hz
Power consumption 25 W
Dimensions (W × H × D) 280 (11") × 200 (7.9") × 248.5 (9.8") mm
Weight 5.5 kg (12.1 lbs)
Accessories Mini plug cable × 1
RCA pin to Mini plug adaptor × 1
1/4" Phone to Mini plug adaptor × 1
* Specifications subject to change without notice.
Controls
Front Panel (Refer to page 2)
4 POWER Switch and Indicator: Press to power on the
YST-MSW10; the power indicator will light up. Press again to
power off. Before powering on and off, turn down the VOLUME
control.
5 HIGH CUT Switch: This switch selects the high-cut filter
frequency: Set it to either LOW or HIGH.
6 VOLUME Control: Use this control to set the volume level. Turn
it clockwise to increase the volume, and counterclockwise to
reduce it.
Auto Power On/Off Function
When powered on, if no input signal is received after 5–10
minutes, the power is switched off automatically. When an input
signal is received, the power is switched back on automatically.
This function works only when the power switch is in the on
position.
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Yamaha YST-MSW10 Ohjekirja

Yamaha
Brändi
Yamaha
Malli
YST-MSW10
Tyyppi
Ohjekirja
Tämä käsikirja sopii myös
Lataa PDF
raportti

muilla kielillä

Liittyvät paperit