Yamaha P-105B Omistajan opas

Brändi: Yamaha

Malli: P-105B

Kategoria: Digital pianos

Tyyppi: Omistajan opas

Tämä käsikirja sopii myös

P-105

1 0 5

D I G I T A L P I A N O

Owner’s Manual

P-105 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING: Do not place this product in a position where anyone

could walk on, trip over, or roll anything over power or connecting

cords of any kind. The use of an extension cord is not recommended!

If you must use an extension cord, the minimum wire size for a 25’

cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the

larger the current handling capacity. For longer extension cords, con-

sult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be dealer

assembled or installed. Please make sure that benches are stable and

any optional fixtures (where applicable) are well secured BEFORE

using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes necessary,

contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

P-105 Owner’s Manual

Contents

Accessories............................................................. 3

About the Manuals .................................................. 4

PRECAUTIONS ...................................................... 4

Introduction

Panel Controls and Terminals 6

Setting Up 7

Turning the Power On/Off....................................... 7

Setting the Volume.................................................. 7

Using Headphones ................................................. 7

Connecting External Audio Equipment ................... 7

Using a Footswitch.................................................. 8

Using the Optional Pedal Unit................................. 8

Reference

Selecting & Playing Voices 9

Selecting a Voice .................................................... 9

Layering Two Voices (Dual).................................... 9

Splitting the Keyboard (Split) ................................ 10

Using the Pianist Styles ........................................ 10

Playing Duo........................................................... 11

Adding Variations to the Sound – Reverb............. 12

Setting the Touch Sensitivity................................. 12

Transposing the Pitch in Semitones ..................... 13

Fine-Tuning the Pitch............................................ 13

Listening to the Songs 14

Listening to the Demo Songs................................ 14

Listening to the Preset Songs ............................... 14

Using the Metronome/Rhythm 15

Selecting a Beat (Time Signature).........................15

Selecting a Rhythm ............................................... 15

Adjusting the Tempo..............................................15

Adjusting the Volume.............................................15

Recording Your Performance 16

Quick Recording .................................................... 16

Recording Independently to Two Parts .................16

Changing the Initial Settings of the Recorded Song

..17

Transferring SMF Files Between a Computer

and this Instrument ............................................17

Deleting the Entire Song........................................18

Song Playback and Practice 18

Backup Data and Initializing 19

Auto Power Off Function 19

Appendix

Troubleshooting 20

Specifications 20

Preset Song List 21

Quick Operation Guide 22

Accessories

• Owner’s Manual

• AC Power Adaptor*

• Online Member Product Registration**

• Footswitch

* May not be included depending on your particular area. Please check with

your Yamaha dealer.

** The PRODUCT ID on the sheet will be needed when you fill out the User

Registration form.

•Music Rest

Insert into the slot

Thank you for purchasing this Yamaha Digital Piano!

We recommend that you read this manual carefully so that you can fully take advantage of the advanced

and convenient functions of the instrument.

We also recommend that you keep this manual in a safe and handy place for future reference.

P-105 Owner’s Manual

In addition to this Owner’s Manual, the following Online materials (PDF files) are available.

Computer-related Operations

Contains instructions about computer-related functions.

MIDI Reference

Contains MIDI-related information, such as the MIDI Implementation Chart.

MIDI Basics (only in English, French, German and Spanish)

Contains basic explanations about what MIDI is and can do.

To obtain the documents above, access the Yamaha Manual Library, enter your model name in the Model Name

area, then click [SEARCH].

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 20) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

About the Manuals

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

DMI-5 1/2

P-105 Owner’s Manual

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected cables, to prevent damage

to the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Use only the stand specified for the instrument. When attaching the stand or rack,

use the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the

desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel or

keyboard. This could cause physical injury to you or others, damage to the

instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (power lamp is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Notice

To avoid the possibility of malfunction/ damage to the product,

damage to data, or damage to other property, follow the notices

below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the instrument, TV, or radio may

generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage to the internal components

or unstable operation. (Verified operating temperature range: 5° – 40°C, or 41° –

104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry/dry or slightly damp cloth. Do not

use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping

cloths.

 Saving data

• Some types of data (page 19) will be stored in internal memory, and maintained

even if the power is turned off. However, the data could be lost due to malfunction

or incorrect operation. Save important data to a computer. For details, refer to the

Computer-related Operations (page 4).

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to

MIDI data and/or audio data is strictly prohibited except for your personal use.

• This product incorporates and bundles computer programs and contents in which

Yamaha owns copyrights or with respect to which it has license to use others’

copyrights. Such copyrighted materials include, without limitation, all computer

software, style files, MIDI files, WAVE data, musical scores and sound recordings.

Any unauthorized use of such programs and contents outside of personal use is

not permitted under relevant laws. Any violation of copyright has legal

consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may

not be exactly the same as the original.

 About this manual

• The illustrations and LCD screens as shown in this manual are for instructional

purposes only, and may appear somewhat different from those on your

instrument.

• The company names and product names in this manual are the trademarks or

registered trademarks of their respective companies.

Power supply/AC power adaptor

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

P-105 Owner’s Manual

Panel Controls and Terminals

q [ ] (Standby/On) switch ....................... page 7

For turning the power on or setting to standby.

w [MASTER VOLUME] slider..................... page 7

For adjusting the volume of the entire sound.

e [DEMO/SONG] button ...........................page 14

For playing the Demo Songs and the Preset Songs.

r TEMPO [][]/SELECT [][]buttons

................................................................page 14

For selecting a Song during playback, adjusting the

tempo, and selecting the Song part for recording

and playback.

t [METRONOME/RHYTHM] button..........page 15

For starting or stopping the metronome or rhythm.

y [PIANIST STYLE] button .......................page 10

For using the Pianist Styles.

u [REC] button ..........................................page 16

For recording your keyboard performance.

i [PLAY] button ........................................page 16

For playing back the recorded performance.

o Voice buttons.......................................... page 9

For switching the Voice between those printed

above and below each button.

For selecting a Voice or two Voices played simulta-

neously, such as Piano and Organ.

!0 [USB TO HOST] terminal

For connecting to a computer, allowing you trans-

fer the User Song data as SMF, and transmit MIDI

messages between both devices. For details, refer

to the “Computer-related Operations” and the

“MIDI Reference.”

!1 [SUSTAIN] jack........................................page 8

For connecting the included footswitch, an

optional footswitch and foot pedal.

!2 [PEDAL UNIT] jack ..................................page 8

For connecting an optional pedal unit.

!3 AUX OUT [L/L+R][R] jacks .....................page 7

For connecting external audio equipment.

!4 DC IN jack ................................................page 7

For connecting the power adaptor.

!5 [PHONES] jacks ......................................page 7

For connecting a set of standard stereo head-

phones.

!3 !4!2!1!0

qwerty

ui o

C0 C1 C2 C3 C4 C5 C6 C7

A-1

Built-in Speakers

Speakers are built into the instrument at the bottom. Though you can

enjoy playing the instrument even when putting it on a desk or table,

we recommend that you use an optional keyboard stand for better

sound.

Shows the jacks and terminals as seen when viewed from the rear of the instrument.

• Use an AB type USB cable of less than 3 meters. USB

3.0 cables cannot be used.

NOTICE

Introduction

P-105 Owner’s Manual

Setting Up

1 Connect the AC power adaptor to the DC IN jack.

2 Plug the AC power adaptor into an AC outlet.

3 Press the [ ] (Standby/On) switch to turn on the

power.

The power lamp located to the left of the [ ]

(Standby/On) switch lights up. To turn off the

power, press this switch again.

When you start playing, use the [MASTER VOL-

UME] slider to adjust the volume of the entire key-

board sound.

I.A. Control (Intelligent Acoustic Control)

With this function, the sound quality of this instru-

ment is automatically adjusted and controlled accord-

ing to the overall volume. Even when the volume is

low, you can hear both low sounds and high sounds

clearly.

To turn on/off the I.A. Control:

While holding down [DEMO/SONG] and [MET-

RONOME/RHYTHM] simultaneously, press the

C#5 key to turn on or D5 to turn off. The default

setting is “on”.

To adjust the I.A. Control Depth:

While holding down [DEMO/SONG] and [MET-

RONOME/RHYTHM] simultaneously, press the

A#4 key to decrease by one, C5 to increase by one,

or B4 to reset to 0 (default). The setting range is

from -3 to +3.

For details on the key assignments, see “Quick Opera-

tion Guide” (page 22).

Since this instrument is equipped with two

[PHONES] jacks, you can connect two sets of stan-

dard stereo headphones. If you are using only one set

of headphones, insert a plug into either jack, shutting

off the speakers.

To amplify the instrument’s sound, you can connect a

stereo system to the AUX OUT [L/L+R]/[R] jacks via

the Phone plugs (standard). The volume of the sound

output from those jacks will be adjusted via the

[MASTER VOLUME] slider.

Turning the Power On/Off

• Use only the specified adaptor (page 20). Using the

wrong adaptor can result in damage to the instrument

or overheating.

• Even when the [ ] (Standby/On) switch is in standby

status (power lamp is off), electricity is still flowing to

the instrument at the minimum level.

When you are not using the instrument for a long time,

make sure you unplug the power cord from the wall AC

outlet.

• Note that the power is automatically turned off if this

instrument is not operated for 30 minutes. For details,

see page 19.

Setting the Volume

WARNING

CAUTION

AC power

adaptor

AC outlet

IMPORTANT

Increases.Decreases.

Using Headphones

• To protect your hearing, avoid listening with the head-

phones at a high volume level for long periods of time.

Connecting External Audio Equipment

• When the instrument’s sound is output to an external

device, first turn on the power to the instrument, then to

the external device. Reverse this order when you turn the

power off.

• Use audio cables and adaptor plugs having no (zero) resistance.

• Use only the [L/L+R] jack for connection with a monaural device.

Standard stereo

phone plug

CAUTION

NOTICE

NOTE

Setting Up

P-105 Owner’s Manual

The [SUSTAIN] jack is for connecting the included

footswitch, which works in the same way as a damper

pedal on an acoustic piano. Also an optional FC3 foot

pedal or FC4/FC5 footswitch can be connected to this

jack. The FC3 lets you use the Half Pedal function.

Half Pedal function (for FC3 and LP-5A/LP-

5AWH)

If you are playing the piano with sustain and want

a clearer, less muddled sound (especially in the

bass register), let up on your foot from the pedal to

half position or higher.

The [PEDAL UNIT] jack is for connecting an

optional LP-5A/LP-5AWH pedal unit. When connect-

ing the pedal unit, make sure to also assemble the unit

on an optional keyboard stand (L-85/L-85S/L-

85WH).

Damper (Right) Pedal

Pressing this pedal will sustain notes longer. Releas-

ing this pedal immediately stops (damps) any sus-

tained notes. A “half-pedal” function of this pedal

creates partial sustain effects, depending on how far

down you press the pedal.

Damper Resonance

This function simulates the sustain sound produced

via the damper pedal on a grand piano.

To turn on/off the Damper Resonance:

While holding down [DEMO/SONG] and [MET-

RONOME/RHYTHM] simultaneously, press the

G4 key (on; default) or G#4 key (off).

Sostenuto (Center) Pedal

If you play a note or chord on the keyboard and press

the sostenuto pedal while the note(s) are held, those

notes will sustain as long as you hold the pedal (as if

the damper pedal had been pressed) but all subse-

quently played notes will not be sustained. This makes

it possible to sustain a chord, for example, while other

notes are played “staccato.”

Soft (Left) Pedal

The soft pedal reduces the volume and slightly

changes the timbre of notes played while the pedal is

pressed. The soft pedal will not affect notes that are

already playing when it is pressed.

Using a Footswitch

• Do not press the footswitch when turning the power on. Doing this changes

the recognized polarity of the footswitch, resulting in reversed footswitch

operation.

• Make sure that power is OFF when connecting or disconnecting the foot-

switch or pedal.

Using the Optional Pedal Unit

• Make sure that power is OFF when connecting or disconnecting the pedal unit.

• The Damper Resonance cannot be used in Duo (page 11).

NOTE

LP-5A/

LP-5AWH

(optional)

L-85/L-85S/

L-85WH

(optional)

NOTE

• When you select the JAZZ ORGAN or ROCK ORGAN Voice, the Left pedal func-

tions to switch the rotary speed of the rotary speaker.

If you press and hold the damper pedal here,

all the notes shown will be sustained.

G#4 (off)

G4 (on)

If you press and hold the sostenuto pedal here,

only the notes held at this timing will be sustained.

NOTE

P-105 Owner’s Manual

Reference

Selecting & Playing Voices

The instrument has a wide variety of Voices, or instru-

ment sounds, for your enjoyment, including Piano and

Organ.

Press a Voice button once or twice.

Pressing the same Voice button repeatedly alter-

nates the on/off status of the lamp, changing

between the Voices whose names are printed

above (lamp off) and below (lamp on) the buttons.

Voice List

Play the keyboard.

You can play Voices simultaneously across the entire

range of the keyboard. Note that the Voice of the left

side button is designated as Voice 1, while the Voice

of the right side button is designated as Voice 2.

Engage Dual.

Press the desired Voice button once or twice

(depending on the desired Voice), then while hold-

ing down that button, press the other Voice button

once or twice. When the lamp is off, the Voice

printed above the button is selected; when the

lamp is on, the Voice printed below is selected.

When the buttons are released, Dual is engaged.

The lamp indicates the status of the Voice 1 selec-

tion.

Play the keyboard to enjoy the dual

sound.

To shift the Octave for each Voice:

To shift Voice 1, simultaneously hold down

[METRONOME/RHYTHM] and press the A4

key to lower by one, B4 to raise by one, or A#4 to

reset to the default setting. For Voice 2, simultane-

ously hold down [METRONOME/RHYTHM]

and press the C5 key to lower by one, D5 to raise

by one, or C#5 to reset to the default setting. The

setting range is from -3 to +3 for both Voices.

Selecting a Voice

Voice Name Description

GRAND PIANO 1

Sampled from a concert grand piano. It

uses different samples depending on the

playing strength and produces smoother

tonal changes. Suitable not only for classi-

cal compositions but also for any style

music.

GRAND PIANO 2

Spacious and clear piano with bright

reverb. Good for popular music.

E. PIANO 1

An electronic piano sound created by FM

synthesis. Good for standard popular

music.

E. PIANO 2

A slightly brighter electronic piano sound

than E. PIANO 1. Good for standard popu-

lar music.

E. PIANO 3

Vintage electric piano sound of hammer-

struck metallic “tines.” Soft tone when

played lightly, and an aggressive tone

when played hard.

E. PIANO 4

Another vintage electric piano sound dif-

ferent from E. PIANO 3 often heard in rock

and popular music.

JAZZ ORGAN

A “tonewheel” type electric organ. Often

heard in jazz and rock music.

PIPE ORGAN

A typical pipe organ sound (8 feet + 4 feet

+ 2 feet). Good for sacred music from the

Baroque period.

ROCK ORGAN

Bright and edgy electric organ sound.

Good for rock music.

VIBRAPHONE

Played with relatively soft mallets. The

tone becomes more metallic the harder

you play.

STRINGS

Stereo-sampled, large-scale strings

ensemble with realistic reverb. Try com-

bining this Voice with piano in the Dual

mode.

HARPSI-

CHORD

The definitive instrument for baroque

music. Authentic harpsichord sound, with

plucked strings, no touch response, and

characteristic key-release sound.

WOOD BASS

An upright bass played fingerstyle. Ideal

for jazz and Latin music.

E. BASS

For a wide range of music styles, jazz,

rock, popular, and more.

Lamp

• To familiarize yourself with the characteristics of the voices, listen to the

demo songs for each voice (page 14).

• You can shift the Octave as described in the next column (see “Voice 1”).

Layering Two Voices (Dual)

• Two Voices of the same button cannot be layered (for example, STRINGS and

HARPSICHORD).

NOTE

Lamp

Voice 1 Voice 2

A4 D5

Selecting & Playing Voices

P-105 Owner’s Manual

To adjust the balance between two Voices:

While holding down [METRONOME/

RHYTHM], press the E5 key to decrease by one,

F#5 to increase by one, or F5 to reset to the default

setting. The setting range is from -6 to +6. Settings

above the default increase the volume of Voice1,

and vice versa.

To exit from Dual, simply press any

Voice button.

You can play different Voices your left and right

hands.

While holding [L], press a Voice button

to engage Split.

The Left Voice (Voice 2) is selected. The keyboard

is divided into the two sections with the F#2 key

as the Split Point.

To change the Right Voice (Voice 1) in

this status, select a Voice while holding

[R].

To shift the Octave for each Voice:

Same as in Dual (page 9).

To adjust the volume balance between two

Voices:

Same as in Dual (see column at left).

To change the Split Point:

While holding [L], press the desired key.

To exit from Split, simply press any

Voice button.

You can automatically play arpeggio-like rhythms by

specifying the chord type with your left hand, while

playing a melody with your right hand.

Press [PIANIST STYLE] so that the lamp

flashes.

The keyboard is divided into the Chord section

(Left) and Melody section (Right).

While holding [PIANIST STYLE], press a

key from the E2 – C#3 to select the

desired Style.

For details on which Pianist Style is assigned to

each key, see “Quick Operation Guide” (page 22).

Splitting the Keyboard (Split)

• Only Dual or Split can be called up; both cannot be used together.

F#5 (+1)

(-1)

(Default)

Split Point (Default: F#2)

Left Voice (Voice 2) Right Voice (Voice 1)

NOTE

Using the Pianist Styles

Split Point (Default: F#2)

Chord section Melody section

C#3

Selecting & Playing Voices

P-105 Owner’s Manual

Play a chord with your left hand to start

playback of the Pianist Style.

Play a melody with your right hand, along with

the chords you play.

To change the tempo:

Basically, this is the same as Metronome tempo

(page 15). In addition, you can change the tempo

also by pressing the specified keys while holding

[PIANIST STYLE]. For details about the key

assignment, refer to the Quick Operation Guide

(page 22).

To adjust the Pianist Style Volume:

While holding down [PIANIST STYLE], press

one of the A-1 – F#0 keys. The higher the key, the

higher the volume. The default value is 7 (D#-1).

Press [PIANIST STYLE] to stop

playback.

The lamp turns off, and the keyboard returns to the

original status.

To change the Split Point:

Same as in Split (page 10).

This function allows two different players to play the

instrument, one on the left and the other on the right,

over the same octave range.

While holding down [DEMO/SONG] and

[METRONOME/RHYTHM]

simultaneously, press the G6 key to

engage Duo.

The keyboard is divided into two sections, with

the E3 key as the Split Point.

One person should play the left section

of the keyboard while the other plays the

right.

To change the Left Voice:

While holding down [L], press a Voice button

once or twice.

To change the Right Voice:

While holding down [R], press a Voice button

once or twice.

To change the Right and Left Voices to the

same single Voice:

Simply press the Voice button once or twice.

To shift the Octave for each Voice:

Same as in Dual (page 9).

To adjust the volume balance between two

keyboard sections:

Same as in Dual (page 10).

Pedal function in Duo

The Footswitch connected to the [SUSTAIN] jack

affects both Right and Left sections. The optional

Pedal unit (page 8) functions as follows:

• Damper Pedal: Applies Sustain to the right sec-

tion.

• Sostenuto Pedal: Applies Sustain to both sec-

tions.

• Soft Pedal: Applies Sustain to the left section.

To exit from Duo, press the G6 key while

holding [DEMO/SONG] and

[METRONOME/RHYTHM]

simultaneously.

• For details on how to play Chords, refer to commercially available chord

books.

• Refer to the numbers 1 – 10 printed in the VOLUME section above the

keyboard.

Playing Duo

NOTE

F#0

A-1

NOTE

• The Split Point cannot be changed from E3.

• If the keyboard is in Dual, engaging Duo will exit from Dual. The Voice 1

is used as the Voice of the entire keyboard.

Split Point

Left Voice (Voice 2) Right Voice (Voice 1)

Equivalent to C3 (middle C) Equivalent to C3 (middle C)

NOTE

Selecting & Playing Voices

P-105 Owner’s Manual

This instrument features several Reverb Types that

add extra depth and expression to the sound to create a

realistic acoustic ambience. Although the appropriate

Reverb Type is called up automatically when you

select each of the Voices, Songs, and Pianist Styles,

you can change the Reverb Type.

To select a Reverb Type:

While holding down [METRONOME/RHYTHM],

press one of the G#6 – C7 keys.

Reverb Type List

To adjust Reverb Depth:

While holding down [METRONOME/RHYTHM],

press the F6 key to decrease by one, G6 to increase by

one, or F#6 to reset to the default value (most suitable

value for the current Voice). The higher the value, the

deeper the effect. The setting range is from 0 (no

effect) – 20 (maximum depth).

You can specify the degree of Touch Sensitivity (how

the sound responds to your playing strength).

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press one of the A6 – C7 keys.

Adding Variations to the Sound –

Reverb

Key

Reverb

Type

Description

G#6Room

Adds a continuous reverb effect to the

sound, similar to the acoustic reverbera-

tion you would hear in a room.

A6 Hall1

For a bigger reverb sound. This effect

simulates the natural reverberation of a

small-size concert hall.

A#6Hall2

For a truly spacious reverb sound. This

effect simulates the natural reverberation

of a large concert hall.

B6 Stage

Simulates the reverb of a stage environ-

ment.

C7 Off No effect is applied.

G#6

F#6 (Default)

(+1)

(-1)

Setting the Touch Sensitivity

Key

Touch

Sensitivity

Description

Fixed

The volume level does not change at all

regardless of whether you play the key-

board soft or hard.

A#6Soft

The volume level does not change much

when you play the keyboard soft or hard.

B6 Medium

This is the standard piano touch response

(default setting).

C7 Hard

The volume level changes very widely

from pianissimo to fortissimo to facilitate

dynamic and dramatic expression. You

have to hit the keys hard to produce a

loud sound.

• The touch sensitivity settings may have little or no effect with JAZZ ORGAN,

ROCK ORGAN, PIPE ORGAN and HARPSICHORD–voices that are not normally

responsive to keyboard dynamics.

C7A6

NOTE

Selecting & Playing Voices

P-105 Owner’s Manual

You can shift the pitch of the entire keyboard up or

down in semitones in order to facilitate playing in dif-

ficult key signatures, or to easily match the pitch of

the keyboard to the range of a singer or other instru-

ments. For example, if “+5” is selected, playing key C

produces pitch F, letting you play a song of F major as

though it were in C major.

To transpose the pitch down:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press a key between F#3 (-6) and

B3 (-1).

To transpose the pitch up:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press a key between C#4 (+1)

and F#4 (+6).

To restore the original pitch:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press the C4 key.

You can fine tune the pitch of the entire instrument in

approximately 0.2 Hz increments. This lets you match

the keyboard pitch finely to that of other instruments

or CD music.

To lower the pitch:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press the C#0 key repeatedly to

lower the pitch in approximately 0.2 Hz increments.

To raise the pitch:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press the D0 key repeatedly to

raise the pitch in approximately 0.2 Hz increments.

To reset the pitch to the default (A3 = 440 Hz):

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press the B-1 key.

To set the pitch to A3 = 442 Hz:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM], press the C0 key.

Transposing the Pitch in Semitones

F#3

F#4

Fine-Tuning the Pitch

• The setting range is from 427.0 Hz to 453.0 Hz. The default setting is A3 = 440.0

Hz.

C#0 (-0.2 Hz)

D0 (+0.2 Hz)

C0 (442.0 Hz)

B-1 (440.0 Hz)

NOTE

P-105 Owner’s Manual

Listening to the Songs

Special individual Demo Songs are provided for all of

the Voices of the instrument.

While holding down [DEMO/SONG],

press one of the desired Voice buttons

once or twice, then release the buttons

to start playback.

Pressing the same Voice button repeatedly alter-

nates the on/off status of the lamp, changing

between the Voices whose names are printed

above (lamp off) and below (lamp on) the buttons.

After selecting a Voice, release both buttons to

start playback. A Demo Song for each Voice will

play back in sequence (from left to right).

To change the Demo Song during playback:

• Select another Voice. For details on selecting a

Voice, refer to page 9.

• Press SELECT [] or [] to call up the previ-

ous or next Demo Song.

To adjust the playback tempo:

While holding down [METRONOME/

RHYTHM], press TEMPO [] or [] to

decrease or increase by one.

Demo Song List

The demonstration pieces listed above are short rearranged excerpts of the origi-

Press [DEMO/SONG] again to stop

playback.

In addition to the Demo Songs, Preset Songs are pro-

vided for your listening pleasure. Choose a Song from

the Preset Song List on page 21, then follow the

instructions below.

While holding down [DEMO/SONG],

press one of the C2 – C#6 keys to start

playback.

Each of the Preset Songs is assigned to each of

these keys. For details on assignment, see “Quick

Operation Guide” (page 22).

The Preset Songs will play back in sequence.

To change to another Song during playback:

• While holding down [DEMO/SONG], press one

of the C2 – C#6 keys.

•Press SELECT [] or [] to call up the previ-

ous or next Demo Song.

To adjust the playback tempo:

While holding down [METRONOME/

RHYTHM], press TEMPO [] or [].

Press [DEMO/SONG] again to stop

playback.

Listening to the Demo Songs

• Simply pressing [DEMO/SONG] will start playback of all Demo Songs

from the first (Grand Piano 1) in sequence.

Voice Name Title

Composer

PIPE ORGAN

Herr Christ, der ein’ge Gottes-Sohn,

BWV.601

J.S. Bach

HARPSI-

CHORD

Concerto a cembalo obbligato, 2 vio-

lini, violae continuo No.7, BWV.1058

J.S. Bach

Lamp

NOTE

Listening to the Preset Songs

1st

Song

10th

Song

20th

Song

30th

Song

40th

Song

50th

Song

C3 C4 C5 C6

P-105 Owner’s Manual

Using the Metronome/Rhythm

The Metronome is convenient for practicing with an accurate tempo. The Metronome sound features several

rhythms as well as the conventional click sound.

Press [METRONOME/RHYTHM] to start

the Metronome.

Press [METRONOME/RHYTHM] again to

stop the Metronome.

While holding down [METRONOME/RHYTHM],

press one of the A0 – D1 keys or one of the Voice but-

tons.

While holding down [METRONOME/RHYTHM],

press one of the E1 – C#2 keys.

For details on which Rhythm number is assigned to

each key, see “Quick Operation Guide” (page 22).

To increase or decrease the value by 1:

When the Metronome/Rhythm is playing back, press

TEMPO [] or []. When it is stopped, press

TEMPO [] or [] while holding down [METRO-

NOME/RHYTHM].

To increase or decrease the value by 1 or 10:

While holding down [METRONOME/RHYTHM],

press one of the D#4 – G4.

To reset the value to the default (120):

When the Metronome/Rhythm is playing back, press

both TEMPO [] and [] simultaneously. When it is

stopped, press both TEMPO [] and [] simultane-

ously or press the F4 key while holding down [MET-

RONOME/RHYTHM].

To specify a three-digit value:

While holding down [METRONOME/RHYTHM],

press a key of F3 – D4 one by one. For example, press

the F3 (0), D4 (9) and A#3 (5) keys in order to specify

“95.”

While holding down [METRONOME/RHYTHM],

press the desired key between the A-1 (left-most key)

and F#0 key. The higher the key, the higher the vol-

ume. The setting range is from 1 – 10 and the default

value is 7.

Selecting a Beat (Time Signature)

• When a Rhythm is selected, the Beat cannot be changed.

Selecting a Rhythm

*Refer to the “METRONOME” section printed above these keys.

A0 D1

No beat

2345

Beat

NOTE

C#2

Adjusting the Tempo

• Refer to the “TEMPO” section printed above these keys.

Adjusting the Volume

• Refer to the “VOLUME” section printed above the keys.

* Refer to the “TEMPO” section printed above these keys.

D#4 (-10) F#4 (+1)

E4 (-1) G4 (+10)

F4 (Default)

NOTE

P-105 Owner’s Manual

Recording Your Performance

You can record your keyboard performance as a User Song in SMF format. Up to two Parts (L and R) can be

recorded separately.

Before recording, make the settings

such as Voice and Beat.

Because some of the settings cannot be changed

after the Record mode is engaged, make the set-

tings according to your performance preferences.

For example, if you want to record your perfor-

mance with a Pianist Style, turn on [PIANIST

STYLE].

Press the [REC] to engage Record

Ready mode.

The [REC] lamp will flash according to the cur-

rent tempo. If necessary, set the tempo (page 15).

Play the keyboard or press [PLAY] to

start recording.

The [REC] lamp lights up while the [PLAY] lamp

flashes at the current tempo.

Play the keyboard and record your performance.

Press either [REC] or [PLAY] to stop

recording.

The [REC] and [PLAY] lamps flash, indicating

that the recorded data is being stored. After Store

is completed, the [REC] lamp turns off.

To hear the recorded Song, press [PLAY]

to start playback.

Press [PLAY] again to stop playback.

Part Assignment

When either the Pianist Style or Split/Duo is used

for recording, the data as listed below will be

recorded to each part.

You can record your performance to the L part (left

hand part) and R part (right hand part) separately.

Before recording, make the settings

such as Voice and Beat.

While holding down [REC], press [R] or

[L] for the part you want to record, to

engage Record ready Mode.

• Note that the Recording operation will replace the already

recorded data with the new data, since only one User Song

is available. Before recording, check the [PLAY] lamp

lights (data available) or not (no data). If you save the

recorded data, transfer it to the computer as a SMF file. For

details, refer to “Computer-related Operations” (page 4).

Quick Recording

• You cannot engage Record mode while a song is playing.

• You can use the Metronome/Rhythm while recording; however, the Met-

ronome/Rhythm sound will not be recorded. When you record the Pia-

nist Style performance, the Metronome/Rhythm cannot be played back

while recording.

NOTICE

NOTE

• Never turn off the power while the recorded data is

being stored (while the lamps are flashing). Other-

wise, all recorded data will be lost.

L part R part

When Pia-

nist Style is

on:

Chord change in the

left hand section

Keyboard perfor-

mance in the right

hand section

When Split or

Duo is on:

Keyboard perfor-

mance in the left

hand section

Keyboard perfor-

mance in the right

hand section

Recording Independently to Two

Parts

• If you select a Part containing data, the Recording opera-

tion will replace the already-recorded data with the new

data.

• If you want to record your performance using Pianist Style, Split or Duo, use the

Quick Recording method (in the previous section), since the instructions below

do not apply to these functions.

NOTICE

NOTE

Recording Your Performance

P-105 Owner’s Manual

To record the right part ([R]):

To record the left part ([L]):

After a while, the [REC] lamp will flash at the

current tempo. If necessary, set the tempo (page

15).

If data has already been recorded to the other

Part:

The data in this Part will be played back while

recording. This Part can be turned off or on by

pressing this Part button while holding down

[PLAY].

Start recording.

Play the keyboard or press [PLAY] to start record-

ing. The [REC] lamp lights up while the [PLAY]

lamp flashes at the current tempo.

Press either [REC] or [PLAY] to stop

recording.

The [REC] and [PLAY] lamps flash, indicating

that the recorded data is being stored. After the

operation is completed, the [REC] lamp will be

turned off.

If desired, record the other part by

repeating Steps 1 – 4.

To hear the recorded Song, Press

[PLAY] to start playback.

Press [PLAY] again to stop playback.

The following parameter settings of the Song can be

changed after the Record operation is completed.

For individual parts:

Voice, Balance, Reverb Depth, Pedal (Damper/

Soft)

For the entire Song:

Tempo, Reverb Type, Pianist Style Volume

Make the settings of the above

parameters.

While holding down [REC], press the

desired Part button to engage Record

Ready mode.

If you want to change the value of the parameters

shared by two parts, select either part.

Press [REC] again to change the initial

settings and to exit from Record Ready

mode.

With Musicsoft Downloader (available for free down-

loading), a SMF file can be transferred between the

computer and the User Song memory area of this

instrument. For details, refer to the “Computer-related

Operations” downloadable from Yamaha Manual

Library (page 4).

• You can use the Metronome/Rhythm while recording; however, the Met-

ronome/Rhythm sound will not be recorded.

• Never turn off the power while the recorded data is

being stored (while the lamps are flashing). Other-

wise, all recorded data will be lost.

NOTE

NOTICE

Changing the Initial Settings of the

Recorded Song

• In this status, do not press [PLAY] again or any key.

Otherwise, recording starts and the data will be

deleted.

Transferring SMF Files Between a

Computer and this Instrument

• Before you transfer an SMF file from a computer, make sure

to transfer the User Song to a computer for safe keeping,

since already-recorded data will be replaced with the new

transfer.

NOTICE

Recording Your Performance

P-105 Owner’s Manual

Press [REC] to engage Record Ready

mode.

The [REC] lamp will flash.

While holding down [PLAY], press [REC]

so that both the lamps flash.

To exit from this status, press any other button

such as [DEMO/SONG].

Press [PLAY], [REC], [L] or [R] to delete

the data of the entire Song.

After the operation is completed, both lamps turn

off.

To delete a specific Part:

While holding down [REC], press [L] or

[R] to engage the Record Ready mode.

The [REC] lamp will flash.

Press [PLAY] to start recording without

playing the keyboard.

Press [REC] or [PLAY] to stop recording.

All data recorded for the selected Part will be

deleted, and the lamp turns off.

Song Playback and Practice

All the Songs except for the Demo (page 14) let you turn on or off the [L] and [R] parts individually. By turning

off [R], for example, you can practice the [R] part while the [L] part is playing back, and vice versa.

Start playback of the desired Song.

To start the User Song, press [PLAY]. To start the

Preset Song, press one of the C2 – C#6 keys to

start playback while holding down [DEMO/

SONG]. For details on what Song number is

assigned to each key, see “Quick Operation

Guide” (page 22).

While holding down [PLAY], press [L] or

[R] repeatedly to turn the Part on/off.

Practice the part which is turned off.

Press [PLAY] to stop playback.

Deleting the Entire Song

• Selecting another Song will cancel the on/off status of the parts.

NOTE

P-105 Owner’s Manual

Backup Data and Initializing

The following data will be maintained as backup data

even if you turn off the power.

Backup data

Metronome/Rhythm Volume, Metronome/Rhythm

selection (Beat or Rhythm number), Touch Sensi-

tivity, Tuning, Split Point, Pianist Style Volume,

Auto Power OFF, Damper Resonance on/off,

I.A.Control on/off, I.A.Control Depth, User Song

To save the User Song data to a computer:

Among the backup data listed above, only the User

Song data can be transferred to a computer and saved

as a SMF file. For details, refer to “Computer-related

Operations” on the website.

To initialize the backup data:

While holding down the C7 key (right-most key), turn

the power on to initialize the backup data to the fac-

tory initial settings.

Both the [REC] and [PLAY] lamps flash, indicating

that the initialization is being executed. After the

operation is completed, both lamps turn off.

Auto Power Off Function

To prevent unnecessary power consumption, this function automatically turns the power off if no buttons or keys

are operated for approximately 30 minutes. If desired, you can disable or enable this function.

To disable Auto Power Off:

When the instrument is turned off:

While holding down the lowest key, press the [ ]

(Standby/On) switch to turn on the power so that the

power indicator flashes three times, after which the

Auto Power Off is disabled.

When the instrument is turned on:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM] simultaneously, press the A-1

key.

To enable Auto Power Off:

While holding down [DEMO/SONG] and [METRO-

NOME/RHYTHM] simultaneously, press the A#-1

key.

• Never turn off the power while the initialization is being

executed.

• If this instrument somehow malfunctions or fails to operate properly, try execut-

ing the initialization.

NOTICE

NOTE

A-1

A#-1

P-105 Owner’s Manual

Appendix

Troubleshooting

Specifications

Dimensions (W x D X H)

• 1,326 x 295 x 163 mm (52-3/16” x 11-5/8” x 6-7/16”)

Weight

• 11.7 kg (25 lbs. 13 oz.)

Keyboards

• 88 keys (A-1 – C7)

• Graded Hammer Standard (GHS) keyboard

• Touch Sensitivity (Hard/Medium/Soft/Fixed)

Voice

• 14 Preset Voices

• Polyphony: 128

Effects/Functions

•4 Reverb types

• Damper Resonance

•Dual

• Split

•Duo

• Intelligent Acoustic Control

Pianist Style

•10 Styles

Song Playback

• 14 Demo Songs + 50 Preset Songs

Song Recording

• 1 User Song with 2 tracks

• Data Capacity: One song 100KB (about 11,000 notes)

•Format

Playback: SMF (format 0, format 1)

Recording: SMF (format 0)

Overall Functions

• Transpose

• Fine Tuning: 427.0 Hz – 453.0 Hz

• Metronome/10 Rhythms

• Tempo (5 – 280)

Connectivity

• DC IN (12V), PHONES (2), SUSTAIN, PEDAL UNIT, USB TO

HOST, AUX OUT

Amplifiers

• 7 W + 7 W

Speakers

• 12 cm x 2 + 5 cm x 2

Power Supply

• AC Power Adaptor PA-150 or an equivalent recommended by

Ya m a h a

Power Consumption

• 7W (When using PA-150 power adaptor)

Included Accessories

• Owner’s Manual, Music Rest, AC Power Adaptor PA-150 or an

equivalent recommended by Yamaha*, Online Member Product

Registration**, Footswitch

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

** The PRODUCT ID on the sheet will be needed when you fill

out the User Registration form.

Options

• Keyboard Stand L-85/L-85S/L-85WH, Pedal Unit (LP-5A/LP-

5AWH), Foot Pedal FC3, Footswitch FC4/FC5, Headphones

(HPE-30/HPE-150), AC Power Adaptor (Users within U.S or

Europe: PA-150 or an equivalent recommended by Yamaha, Oth-

ers: PA-5D, PA-150 or an equivalent)

* Specifications and descriptions in this owner’s manual are for

information purposes only. Yamaha Corp. reserves the right to

change or modify products or specifications at any time without

prior notice. Since specifications, equipment or options may not

be the same in every locale, please check with your Yamaha

dealer.

Problem Possible Cause and Solution

The instrument does not turn on.

The instrument has not been plugged in properly. Securely insert the female plug into

the jack on the instrument, and the male plug into a proper AC outlet (page 7).

The instrument is automatically turned off even if

no operation is done.

This is normal. This occurs due to the Auto Power Off function (page 19).

Noise is heard from the speakers or head-

phones.

The noise may be due to interference caused by the use of a mobile phone in close

proximity to the instrument. Turn off the mobile phone, or use it further away from the

instrument.

The overall volume is low, or no sound is heard.

The Master Volume is set too low; set it to an appropriate level using the [MASTER

VOLUME] slider (page 7).

Make sure a pair of headphones is not connected to the headphones jack (page 7).

Make sure that Local Control is ON. For details, refer to “MIDI Reference” (page 4) on

the website.

The pedal has no effect.

The pedal cable/plug may not be properly connected. Make sure to securely insert the

pedal plug into the [SUSTAIN] or [PEDAL UNIT] jack (page 8).

The footswitch (for sustain) seems to produce

the opposite effect. For example, pressing the

footswitch cuts off the sound and releasing it

sustains the sounds.

The polarity of the footswitch is reversed because the footswitch was pressed when the

power was turned on. Turn off the power and turn it on again to reset the function. Make

sure to not press the footswitch when turning the power on.

Sivu latautuu ...

Yamaha P-105B Omistajan opas

Brändi: Yamaha

Malli: P-105B

Kategoria: Digital pianos

Tyyppi: Omistajan opas

Tämä käsikirja sopii myös

P-105

Lataa PDF

raportti

muilla kielillä

polski: Yamaha P-105B Instrukcja obsługi
Türkçe: Yamaha P-105B El kitabı
English: Yamaha P-105B Owner's manual
čeština: Yamaha P-105B Návod k obsluze
svenska: Yamaha P-105B Bruksanvisning
русский: Yamaha P-105B Инструкция по применению
italiano: Yamaha P-105B Manuale del proprietario
Deutsch: Yamaha P-105B Bedienungsanleitung
português: Yamaha P-105B Manual do proprietário
dansk: Yamaha P-105B Brugervejledning
français: Yamaha P-105B Le manuel du propriétaire
español: Yamaha P-105B El manual del propietario
Nederlands: Yamaha P-105B de handleiding
română: Yamaha P-105B Manualul proprietarului

Liittyvät paperit

Muut asiakirjat

LANDMANN Grillleuchte, LED 3,7V, Schwarz Käyttö ohjeet