Panasonic SCTMAX9EG Käyttö ohjeet

Tyyppi
Käyttö ohjeet
Confidential
Until:
06 Dec 2019
EG
Dziękujemy za zakupienie tego produktu.
Proszę dokładnie zapoznać się z tą instrukcją obsługi,
aby jak najlepiej wykorzystać to urządzenie i zapewnić
jego bezpieczne użytkowanie.
Prosimy o zachowanie niniejszej instrukcji obsługi.
Kiitos, että hankit tämän tuotteen.
Lue nämä ohjeet huolellisesti parhaan suorituskyvyn ja
turvallisuuden takaamiseksi.
Säilytä ohje tulevaa tarvetta varten.
Tak fordi du har valgt dette produkt.
Læs venligst denne betjeningsvejledning omhyggeligt,
således at optimal ydelse og sikkerhed opnås.
Gem vejledningen til senere brug.
Operating Instructions
Bruksanvisning
Betjeningsvejledning
Käyttöohjeet
Instrukcja obsługi
Návod k obsluze
Wireless Speaker System
Trådlöst högtalarsystem
Trådløst højttalersystem
Langaton kaiutinjärjestelmä
Zestaw głośników bezprzewodowych
Bezdrátová souprava reproduktorů
Model No. SC-TMAX9
TQBJ2212
Děkujeme za zakoupení tohoto výrobku.
Pro dosažení optimálního výkonu a z bezpečnostních
důvodu si pečlivě přečtěte tyto pokyny.
Uschovejte si prosím tento návod k obsluze.
Thank you for purchasing this product.
For optimum performance and safety, please read these
instructions carefully.
Please keep this manual for future reference.
Tack för valet av denna apparat.
Läs igenom bruksanvisningen noga för bästa resultat och
för säkerhets skull.
Spara denna bruksanvisning.
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 1 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
2
TQBJ2212
2
Your system and the illustrations can look differently.
The symbols on this product (including the accessories)
represent the following:
Table of contents
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Transporting the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preparing the remote control . . . . . . . . . . . . . . . . . . . . . 5
Overview of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Preparing media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Media playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sound effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DJ functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using a microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Karaoke. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clock and timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
External equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Safety precautions
WARNING!
Unit
To reduce the risk of fire, electric shock or product
damage,
Do not expose this unit to rain, moisture, dripping or
splashing.
Do not place objects filled with liquids, such as vases,
on this unit.
Use the recommended accessories.
Do not remove covers.
Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
Do not let metal objects fall inside this unit.
CAUTION!
Unit
To reduce the risk of fire, electric shock or product
damage,
Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit
is well ventilated.
Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
Do not place sources of naked flames, such as lighted
candles, on this unit.
This unit is intended for use in moderate climates.
This unit may receive radio interference caused by
mobile telephones during use. If such interference
occurs, please increase separation between this unit
and the mobile telephone.
This unit utilizes a laser. Use of controls or adjustments
or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Set the unit up on an even surface away from direct
sunlight, high temperatures, high humidity, and
excessive vibration.
This system might get warm after prolonged usage. This
is normal. Do not be alarmed.
AC mains lead
The mains plug is the disconnecting device. Install this
unit so that the mains plug can be unplugged from the
socket outlet immediately.
Battery
Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
When disposing of the batteries, please contact your
local authorities or dealer and ask for the correct
method of disposal.
Do not heat or expose to flame.
Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and
windows closed.
Do not break open or short-circuit the battery.
Do not charge the alkaline or manganese battery.
Do not use the battery if the cover has peeled off.
Remove the battery if you do not use the remote control
for a long period of time. Keep in a cool, dark area.
AC
DC
Class II equipment (The construction of the
product is double-insulated.)
ON
Standby
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 2 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
3
TQBJ2212
3
Avoid the use in the following conditions
High or low extreme temperatures during use, storage
or transportation.
Replacement of a battery with an incorrect type.
Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a battery, that can
result in an explosion.
Extremely high temperature and/or extremely low air
pressure that can result in an explosion or the
leakage of flammable liquid or gas.
Supplied accessories
Check and identify the supplied accessories.
1 AC mains lead
1 Remote control
(N2QAYB001215)
1 Remote control battery
References
About Bluetooth
®
Frequency band
This system uses the 2.4 GHz frequency band.
Certification
This system conforms to the frequency restrictions and
has received certification based on frequency laws.
Thus, a wireless permit is not necessary.
The actions below are punishable by law in some
countries:
Taking apart or modifying the unit.
Removing specification indications.
Restrictions of use
Wireless transmission and/or usage with all Bluetooth
®
equipped devices is not guaranteed.
All devices must conform to standards set by the
Bluetooth SIG, Inc.
Depending on the specifications and settings of a
device, it can fail to connect or some operations can be
different.
This system supports Bluetooth
®
security features. But
depending on the operating environment and/or
settings, this security is possibly not sufficient. Transmit
data wirelessly to this system with caution.
This system cannot transmit data to a Bluetooth
®
device.
Range of use
Use this device at a maximum range of 10 m.
The range can decrease depending on the environment,
obstacles or interference.
Interference from other devices
This system may not function properly and troubles
such as noise and sound jumps may arise due to radio
wave interference if this unit is located too close to other
Bluetooth
®
devices or the devices that use the 2.4 GHz
band.
This system may not function properly if radio waves
from a nearby broadcasting station, etc. is too strong.
Intended usage
This system is for normal, general use only.
Do not use this system near an equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals, laboratories,
etc.).
Licenses
Panasonic bears no responsibility for data and/or
information that is compromised during a wireless
transmission.
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Panasonic Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
Android and Google Play are trademarks of Google
LLC.
Disposal of Old Equipment and Batteries
Only for European Union and countries with
recycling systems
These symbols on the products, packaging,
and/or accompanying documents mean that
used electrical and electronic products and
batteries must not be mixed with general
household waste.
For proper treatment, recovery and recycling
of old products and used batteries, please
take them to applicable collection points in
accordance with your national legislation.
By disposing of them correctly, you will help to
save valuable resources and prevent any
potential negative effects on human health
and the environment.
For more information about collection and
recycling, please contact your local
municipality.
Penalties may be applicable for incorrect
disposal of this waste, in accordance with
national legislation.
Note for the battery symbol (bottom
symbol):
This symbol might be used in combination
with a chemical symbol. In this case it
complies with the requirement set by the
Directive for the chemical involved.
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 3 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
4
TQBJ2212
4
Transporting the unit
Preparation
Disconnect all connected devices and cables from the
unit.
Note:
Keep the unit at least 10 mm away from other objects for
proper ventilation.
The speakers do not have magnetic shielding. Do not put
them near PCs or other equipment easily influenced by
magnetism.
When you play at high levels for a long period, it can cause
damage to the speakers and decrease the life of the
speakers.
Decrease the volume in these conditions to prevent
damage:
When the sound is distorted.
When you adjust the sound quality.
Maintenance
Disconnect the AC mains lead before maintenance.
Clean this system with a soft, dry cloth.
Never use alcohol, paint thinner or benzine to clean this
system.
Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
Power sources
The unit can be switched on by using AC power supply
source. If AC power supply source is not available, you
can use an external power bank.
Using the household mains socket
Connect the AC mains lead.
Conserving power
The system consumes a small amount of power even
when it is in standby mode. Disconnect the power
supply if you do not use the system.
Some settings will be lost after you disconnect the
system. You have to set them again.
Note:
Do not use any other AC mains lead except the supplied
one.
Hold the unit when connecting or disconnecting the AC
mains lead to prevent the unit from falling.
Keep the antennas away from the AC mains lead to avoid
picking up noise.
CAUTION!
Improper handling or transportation manner may
cause the unit to fall, etc., resulting in damage
and/or personal injury.
Do not touch the speaker cone’s reverberating
surfaces:
This may damage the speaker cone.
The speaker cone may be hot.
Do not put the unit on a table or any elevated
surface.
Do not allow children to climb on the unit.
Be careful when babies or children are near.
To household mains socket
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 4 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
5
TQBJ2212
5
Using an external power bank
Connect the external power bank (not supplied) to the
micro USB port at the rear of the unit.
Note:
“PWR BANK” is shown for 5 seconds when using the
external power bank as the power source.
When the unit is connected to both household mains socket
and external power bank, the power is supplied through the
household mains socket.
If the power supply is disconnected, the unit will switch to
power bank mode and vice versa.
When using power bank as the power source, you cannot do
USB charging.
Power bank cannot be charged while connected to the unit.
Do not use power bank that does not conform to safety
standards.
Do not use power bank output power below 5 V, 2 A.
Do not use damaged power bank. This can cause fire,
electric shock or product damage.
Preparing the remote control
Use alkaline or manganese battery.
Install the battery so that the poles (+ and –) align with
those in the remote control.
USB cable
(not supplied)
ENGLISH
External
power bank
(not supplied)
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 5 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
6
TQBJ2212
6
Overview of controls
Do the procedures with the remote control. You can also use the buttons on the unit if they are the same.
A Standby/on switch [`], [1]
Press to switch the unit from on to standby mode or
vice versa. In standby mode, the unit is still consuming
a small amount of power.
When the unit
s power source is other than household
mains socket, press
[1] on the unit to switch it on.
B Decrease the brightness of the display panel
The illumination is also switched off.
To cancel, press the button again.
C Select the audio source
Press [SELECT <, >] (unit: [SELECT]) repeatedly to
select the source:
On the unit:
To start Bluetooth
®
pairing, press and hold [ ].
D Basic playback control
E View the setup menu
F View the content information
G Select or confirm the option
H Set the sleep timer
I Adjust the volume level
On the unit:
Press [VOL] and then turn [VOLUME/MULTI
CONTROL] to adjust the volume.
Adjust the microphone volume level
Press and hold [–MIC VOL] until “MIC VOL” is shown.
Turn [VOLUME/MULTI CONTROL] to adjust the
volume.
J Mute the sound
To cancel, press the button again.
“MUTE” is also cancelled when you adjust the volume
or when you switch off the system.
K View the play menu
L Select the sound effects
USB
AUXBLUETOOTH
CD D-IN
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 6 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
7
TQBJ2212
7
M Select DJ effect or DJ sampler
N Select the illumination effects
O Select MP3 album or track
Press [ALBUM/TRACK] to select album or track.
Browse tracks or albums
Press [R, T] or turn [VOLUME/MULTI CONTROL] to
browse.
To start playback from the selection, press [4/9].
P Select the Karaoke effects
To cancel, press and hold [–OFF] until “OFF EFFECT”
is shown.
Q Volume or multi control knob
Do not turn knob fast to prevent irregular of volume
operation.
R Select DJ jukebox
Select DEMO play
Press and hold [–DEMO] for more than 2 seconds, the
built-in demonstration song will be played.
Press [8] to stop the demonstration.
S Open or close the disc tray
T DJ function direct buttons
Press [DJ] to switch on the DJ function.
Press [DJ1] to [DJ6] to select the desired function.
To cancel, press the selected [DJ1] to [DJ6] again.
U Microphone jack
V USB port ( )
Play MP3 tracks.
W Remote control sensor
Point the remote control at the remote control
sensor, away from obstacles and within the
operation range.
Distance: Within approximately 7 m
Angle: Approximately 20° up and down, 30° left
and right
X Display panel
Y Disc tray
SELECT
VOL
DJ6
DJ5
DJ4
DJ3
DJ2
DJ1
SOUND
JUKEBOX
KARAOKE
ALBUM/
TRACK
ILLUMINATION
Top panel
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 7 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
8
TQBJ2212
8
Preparing media
Disc
1 Press [x] on the unit to open the disc tray.
Put in a disc with the label facing up.
Press again to close the disc tray.
2 Press [SELECT <, >] repeatedly to select “CD”.
USB
Preparation
Before you connect a USB device to the system, make
sure you do a backup of the data.
1 Decrease the volume and connect the USB device
to the USB port.
2 Press [SELECT <, >] repeatedly to select “USB”.
Note:
Do not use a USB extension cable. The system cannot
recognise USB device connected through a cable.
Some devices cannot be charged as the maximum USB
charging current is 0.5 A only.
Bluetooth
®
You can connect and play an audio device wirelessly
through Bluetooth
®
.
Preparation
Switch on the unit.
Switch on the Bluetooth
®
feature of the device and put
the device near the system.
Read the operating instructions of the device for details.
Pairing a device
Preparation
If this system is connected to a Bluetooth
®
device,
disconnect it (~8).
1 Press [ ].
If “PAIRING” is shown, continue with step 3.
2 Press [PLAY MENU] to select “PAIRING” and then
press [OK].
3 Select “SC-TMAX9” from the Bluetooth
®
menu of
the device.
If prompted for a passkey, input “0000” or “1234”.
The device connects with this system automatically
after pairing is complete.
The MAC address (example: 6C:5A:B5:B3:1D:0F)
may be shown before “SC-TMAX9” is shown.
The name of the connected device is shown for a few
seconds.
Using the unit
1 Press and hold [ ] until “PAIRING” is shown.
2 Select “SC-TMAX9” from the Bluetooth
®
menu of
the device.
Note:
You can pair up to 8 devices with this system. If a 9th device
is paired, the device that has not been used for the longest
time will be replaced.
Depending on the searching functionality of the Bluetooth
®
device and the surrounding environment, if the product
name is not shown on the Bluetooth
®
menu of the device,
switch off and then switch on the Bluetooth
®
feature of the
device repeatedly during the pairing process.
Connecting a device
Preparation
If this system is connected to a Bluetooth
®
device,
disconnect it (~8).
1 Press [ ].
“BLUETOOTH READY” is shown.
2 Select “SC-TMAX9” from the Bluetooth
®
menu of
the device.
The name of the connected device is shown for a few
seconds.
3 Start playback on the device.
Note:
A device must be paired to connect.
When “BLUETOOTH” is selected as the source, this system
will automatically try to connect to the last connected device.
(“LINKING” is shown during this process.)
Multi Connect
This system supports Multi Connect, which can connect
up to 3 devices simultaneously.
To switch between the connected devices
When one of the connected devices is playing, you can
easily switch control to another connected device simply
by starting a playback on that device. The previous
playback will be paused automatically.
Note:
This function may not work for some apps or devices
(depending on app or device specifications).
Disconnecting a device
While a Bluetooth
®
device is connected
1 Press [PLAY MENU] repeatedly to select
“DISCONNECT?”.
2 Press [R, T] to select “OK? YES” and then press
[OK].
“BLUETOOTH READY” is shown.
To cancel, select “OK? NO”.
Using the unit
Press and hold [ ] until “PAIRING” is shown.
Note:
This function disconnects all connected devices.
A device is disconnected when you:
Select a different source.
Move the device out of the maximum range.
Disable the Bluetooth
®
transmission of the device.
Switch off the system or the device.
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 8 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
9
TQBJ2212
9
Media playback
The following marks indicate the availability of the feature.
Basic playback
CD ::USB BLUETOOTH
Note:
Depending on the Bluetooth
®
device, some operations may not
work.
Viewing available information
:CD ::USB BLUETOOTH
You can view the available information, such as MP3
album and track number, on the display panel.
Press [DISPLAY] repeatedly.
Example: MP3 album and track number display.
Note:
Maximum characters that can be shown: Approximately 32
This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.
Text data that the system does not support can show
differently.
Play menu
:CD ::USB
1 :CD :
Press [PLAY MENU].
:USB
Press [PLAY MENU] repeatedly to select
“PLAYMODE”.
2 Press [R, T] to select the setting and then press
[OK].
Note:
During random playback, you cannot skip to tracks which
have been played.
The setting is cancelled when you open the disc tray or
disconnect the USB device.
CD :
:USB :
BLUETOOTH :
CD-R/RW in CD-DA format or with MP3
files.
USB device with MP3 files.
Bluetooth
®
device.
Play Press [4/9].
Stop Press [8].
USB
The position is memorised.
“RESUME” is shown.
Press again to stop fully.
Pause Press [4/9].
Press again to continue playback.
Skip Press [2/3] or [5/6] to skip track.
:CD ::USB
Press [R, T] to skip MP3 album.
Search Press and hold [2/3] or [5/6].
Album
number
Track
number
OFF PLAYMODE Cancel the setting.
1-TRACK Play one selected track.
Press [2/3] or [5/6] to
select the track.
1-ALBUM Play one selected MP3 album.
Press [R, T] to select the MP3
album.
RANDOM Play all tracks randomly.
1-ALBUM
RANDOM
Play all tracks in one selected MP3
album randomly.
Press [R, T] to select the MP3
album.
ALL REPEAT Repeat all tracks.
1-TRACK REPEAT Repeat 1-TRACK.
1-ALBUM REPEAT Repeat 1-ALBUM.
RANDOM REPEAT Repeat random playback.
1-ALBUM
RANDOM REPEAT
Repeat 1-ALBUM RANDOM.
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 9 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
10
TQBJ2212
10
Note on disc
This system can play CD-R/RW with CD-DA or MP3
format content.
Before playback, finalise the disc on the device it was
recorded on.
Some CD-R/RW cannot be played because of the
condition of the recording.
Note on USB device
This system does not guarantee connection with all
USB devices.
This system supports USB 2.0 full speed.
This system can support USB devices of up to 32 GB.
Only FAT 12/16/32 file system is supported.
Note on MP3 file
Files are defined as tracks and folders are defined as
albums.
Tracks must have the extension
“.mp3” or “.MP3”.
Tracks will not necessarily be played in the order you
recorded them.
Some files can fail to work because of the sector size.
MP3 file on disc
This system can access up to:
255 albums (including root folder)
–999 tracks
20 sessions
Disc must conform to ISO9660 level 1 or 2 (except for
extended formats).
MP3 file on USB device
This system can access up to:
800 albums (including root folder)
8000 tracks
999 tracks in one album
Sound effects
1 Press [SOUND] repeatedly to select the effect.
2 Press [R, T] to select the setting and then press
[OK].
Or turn [VOLUME/MULTI CONTROL] to select the
setting.
Illumination
You can change the illumination effect on the system.
1 Press [SETUP] repeatedly to select
“ILLUMINATION”.
Or press [ILLUMINATION] on the unit.
2 Press [R, T] to select the effect and then press
[OK].
Or turn [VOLUME/MULTI CONTROL] to select the
effect.
Note:
When the dimmer function is switched on, the illumination on
the system will remain off even when you switch on the
illumination function.
DJ functions
You can use the DJ functions to add sound effects or
sample sound between songs.
Note:
The DJ function is switched off when you switch off the system
or change to another source.
PRESET EQ
“ROCK”, “POP”, “AFRO BEAT”,
“ARABIC”, “PERSIAN”, “INDIA
BASS”, “DANGDUT”, “MALAY
POP”, “ELECTRONICA”,
“REGGAETON”, “SALSA”,
“SAMBA”, “KARAOKE” or “FLAT”
BASS/MID/TREBLE –4 to +4
Note:
These settings can change when you
select a PRESET EQ setting.
D.BASS LEVEL “OFF”, “LEVEL 1” to “LEVEL 6”
PATTERN A selection of 3 illumination patterns in blue.
OFF Cancel the effect.
Using the “Panasonic MAX Juke” app
You can download and install the free Android™ app
“Panasonic MAX Juke” on Google Play™ for additional
features, such as to request song playback from multiple
devices simultaneously. You can also call up the tracks
you want to play through the app. For details on the app,
refer to the site below.
http://av.jpn.support.panasonic.com/support/global/
cs/audio/app/
(This site is in English only.)
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 10 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
11
TQBJ2212
11
DJ jukebox
:USB
You can use the DJ jukebox function to add sample sound
mix between songs.
1 Press [PLAY MENU] to select “JUKEBOX”.
2 Press [R, T] to select the setting and then press
[OK].
Using the unit
1 Press [JUKEBOX] to select “DJ JUKEBOX
SELECT NUMBER”.
To cancel, select “OFF JUKEBOX”.
2 Press [DJ1] to [DJ6] to select the effect.
Sample sound is added to the intervals of all tracks.
To cancel, press the button again.
Note:
The system switches to repeat mode automatically when you
switch on DJ jukebox.
Changing the repeat setting
1 Press
[PLAY MENU] repeatedly to select
“PLAYMODE”.
2 Press [R, T] to select the setting and then press
[OK].
Note:
You cannot select the DJ jukebox effect when you are using
“RANDOM MIX REPEAT” mode.
DJ effect
(Except for D-IN and AUX source)
By unit only
You can use the DJ effect function to add sound effects.
1 Press [DJ] to select “DJ EFFECT SELECT
NUMBER” or “ON DJ EFFECT”.
To cancel, select “OFF EFFECT”.
2 Press [DJ1] to [DJ6] to select the effect.
To cancel, press the button again.
3 Turn [VOLUME/MULTI CONTROL] to select the
setting.
Note:
DJ effect is switched off when you switch off the system,
change to D-IN, AUX source.
DJ sampler
(Except for D-IN and AUX source)
By unit only
You can apply a scratch sound or sample sound to the
track you are playing.
1 Press [DJ] to select “SAMPLER SELECT
NUMBER” or “ON SAMPLER”.
To cancel, select “OFF EFFECT”.
2 Press [DJ1] to [DJ6] to select the desired sound.
To cancel, press the button again.
3 Turn [VOLUME/MULTI CONTROL].
Using a microphone
Preparation
Decrease the volume of the system to its minimum before
you connect or disconnect a microphone.
1 Connect a microphone (not supplied) to the
microphone jack.
Plug type: Ø 6.3 mm monaural
2 Press [SOUND] on the remote control repeatedly
to select “MIC VOL”.
Or press and hold [–MIC VOL] until “MIC VOL” is
shown.
3 Press [R, T] to adjust the volume of the
microphone and then press [OK].
Or turn [VOLUME/MULTI CONTROL] to adjust the
volume of the microphone.
4 If you want to sing with the background music,
play the music source and adjust the volume of
the system.
Note:
If a strange noise (howling) is emitted, move the microphone
away from the speakers, or decrease the volume of the
microphone.
When you do not use the microphone, disconnect it from the
microphone jack, and decrease the volume of the
microphone to its minimum.
RANDOM REPEAT Repeat random playback.
ALL TITLE REPEAT Repeat all tracks.
RANDOM MIX
REPEAT
Repeat random playback. Sample
sound is added to the intervals of
all tracks.
[DJ1] PHASER
Add space and dimension to the sound.
[DJ2] FILTER
Enhance or filter specific ranges of the sound.
[DJ3] SOUND CHOPPER
Cut off the sound periodically.
[DJ4] ELECTRO ECHO
Add digital echo to the sound.
[DJ5] PITCH SHIFTER
Adjust the keys of the sound.
[DJ6] HARMONIZER
Add notes to the sound to create harmony.
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 11 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
12
TQBJ2212
12
Karaoke
Preparation
Select the music source.
Note:
The Karaoke function is switched off when you switch off the
system.
Karaoke effect
You can use the Karaoke effect function to add sound
effects.
1 Press [SOUND] on the remote control repeatedly
to select “KARAOKE EFFECT” and then press
[R, T] to select the effect.
Or press [KARAOKE] repeatedly to select the effect.
To check the current setting, press [OK].
2 Press [2/3] or [5/6] to select the setting
and then press [OK].
Or turn [VOLUME/MULTI CONTROL] to select the
setting.
Clock and timers
Setting the clock
This is a 24-hour clock.
1 Press [SETUP] repeatedly to select “CLOCK”.
2 Press [R, T] to set the time and then press [OK].
To check the time
Press [SETUP] to select “CLOCK” and then press
[OK].
In standby mode, press [DISPLAY].
Note:
The clock is reset when there is a power failure or when the
AC mains lead is disconnected.
Reset the clock regularly to maintain accuracy.
Sleep timer
The sleep timer switches off the system after the set time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select “OFF”.
To check the remaining time
Press [SLEEP].
Note:
The remaining time is shown for a few seconds every
minute. “SLEEP 1” is always shown when only 1 minute
remains.
The sleep timer always comes first. Be sure not to set an
overlap of timers.
Play timer
(Except for Bluetooth
®
, D-IN and AUX source)
You can set the timer to come on at a certain time to wake
you up.
Preparation
Set the clock.
1 Press [SETUP] repeatedly to select “TIMER ADJ”.
2 Press [R, T] to select “ PLAY” and then press
[OK].
3 Press [R, T] to set the start time and then press
[OK].
4 Do step 3 again to set the end time.
5 Press [R, T] to select the source you want to play
and then press [OK].
To start the timer
1 Prepare the source you want to listen to (disc or
USB).
2 Press [SETUP] repeatedly to select “TIMER SET”.
VOCAL
CANCEL
Reduce the vocal level or change the
audio mode (depending on the source).
ECHO Add an echo effect to the sound.
KEY
CONTROL
Change the key of a song.
TEMPO
:USB
Change the speed of a song.
BGM Change the background music level.
MIC EQ Select a MIC EQ mode.
OFF
EFFECT
Cancel the effect.
Press [OK] to confirm.
Or press and hold [–OFF] until “OFF
EFFECT” is shown.
VOCAL
CANCEL
“OFF”, 1 to 3, “L”, “R”, “L+R”
When using stereo source not
formatted for Karaoke
It is recommended to use “2 VOCAL
CANCEL” for most songs.
When using Karaoke formatted
source
L: Only left channel sound
(accompaniment only)
R: Only right channel sound (vocals
only)
L+R: Left and right channel sounds are
mixed
ECHO “OFF”, 1 to 4
KEY
CONTROL
–6 to +6
TEMPO “OFF”, –2 to +2
BGM “OFF”, 1 to 3
MIC EQ “SINGING” or “SPEECH”
SLEEP 30 SLEEP 60 SLEEP 90 SLEEP120
OFF
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 12 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
13
TQBJ2212
13
3 Press [R, T] to select “PLAY ON” and then press
[OK].
To cancel, select “PLAY OFF”.
The system must be switched off for the timer to
operate.
To check the setting
1 Press [SETUP] repeatedly to select “TIMER ADJ”.
2 Press [R, T] to select “ PLAY” and then press
[OK].
In standby mode, press [DISPLAY] two times.
Note:
The timer starts at a low volume and increases gradually to
the preset level.
The timer comes on at the set time every day if the timer is
on.
If you switch off the system and then switch on again while a
timer is in operation, the timer will not stop at the end time.
External equipment
Preparation
Disconnect the AC mains lead.
Switch off all equipment and read the appropriate
operating instructions.
Note:
Do not bend cables at sharp angles.
Components and cables are sold separately.
Sound distortion can occur when you use an adapter.
If you want to connect equipment other than those
described, refer to the audio dealer.
Using the optical input
You can connect a TV, VCR, DVD player etc., and listen to
the audio through this system.
1 Connect the external equipment.
2 Press [SELECT <, >] repeatedly to select “D-IN”.
3 Play the external equipment.
Note:
This system supports linear PCM signal.
Multi-channel source will be converged to 2 channels.
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz, up to 96 kHz
The sound is muted if the signal format or frequency is not
supported.
If there are sounds coming from the TV’s speakers,
decrease the volume of the TV to its minimum.
Using the auxiliary input
You can connect a VCR, DVD player etc., and listen to the
audio through this system.
1 Connect the external equipment.
2 Press [SELECT <, >] repeatedly to select “AUX”.
3 Play the external equipment.
Rear panel
of this unit
Audio cable
(not supplied)
DVD player (not supplied)
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 13 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
14
TQBJ2212
14
Others
Auto off
This function will automatically switch the unit to standby
mode if there is no sound and it is not being used for
approximately 20 minutes.
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [R, T] to select “ON” and then press [OK].
To cancel, select “OFF”.
Note:
This function may not work when a microphone is
connected.
The factory default is “ON”. To switch off this function, select
“OFF”.
Bluetooth
®
standby
This function automatically switches on the system when
you establish a Bluetooth
®
connection from a paired
device.
1 Press [SETUP] repeatedly to select “BLUETOOTH
STANDBY”.
2 Press [R, T] to select “ON” and then press [OK].
To cancel, select “OFF”.
Note:
This function only works when the AC mains lead is
connected.
Some devices may take longer to respond. If you are
connected to a Bluetooth
®
device before switching off the
system, wait for a minimum of 5 seconds before connecting
to this system from your Bluetooth
®
device again.
Software update
Occasionally, Panasonic may release updated software
for this unit that may add or improve the way a feature
operates. These updates are available free of charge. For
more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Checking the software version
1 Press [SETUP] repeatedly to select “SW VER.
and then press [OK].
The software version is shown.
2 Press [OK] again to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult your
dealer for instructions.
Common problems
The unit does not work.
The safety device has been activated. Do the following:
1. Press [1] on the unit to switch the unit to standby mode.
If the unit does not switch to standby mode, disconnect
the AC mains lead and then connect it again.
2. Press [1] again to switch on the unit. If the problem
persists, consult your dealer.
The display panel lights up and changes continuously in
standby mode.
Press and hold [8] on the unit until “SDEMO OFF” is shown.
No operations can be done with the remote control.
Examine that the battery is installed correctly.
Sound is distorted or no sound.
Adjust the volume of the system.
Switch off the system, determine and correct the cause, and
then switch on again. It can be caused by straining of the
speakers through excessive volume or power, and when
using the system in a hot environment.
A humming sound can be heard during playback.
An AC mains lead or fluorescent light is near the cables.
Keep other appliances and cords away from the cables of
this system.
The sound level reduces.
The protection circuit has been activated due to the
continuous use at high volume output. This is to protect the
system and maintain the sound quality.
Disc
Display not shown correctly.
Playback does not start.
You have not put in the disc correctly. Put it in correctly.
Disc is dirty. Clean the disc.
Replace the disc if it is scratched, warped, or non-standard.
There is condensation. Let the system dry for 1 to 2 hours.
The total number of tracks shown is incorrect.
The disc cannot be read.
Distorted sound is heard.
You put in a disc that the system cannot play. Change to a
playable disc.
You put in a disc that has not been finalised.
USB
The USB device or the contents in it cannot be read.
The format of the USB device or the contents in it are not
compatible with the system.
USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
Slow operation of the USB device.
Large content size or large memory USB device takes
longer time to read.
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 14 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
15
TQBJ2212
15
Bluetooth
®
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device is out of the 10 m communication range. Move
the device nearer to the system.
The device cannot be connected.
The pairing of the device was unsuccessful. Do pairing again
(~8).
The pairing of the device has been replaced. Do pairing
again (~8).
This system might be connected to a different device.
Disconnect the other device and try connecting the device
again.
The system may have a problem. Switch off the system and
then switch on again.
The device is connected but audio cannot be heard
through the system.
For some built-in Bluetooth
®
devices, you have to set the
audio output to “SC-TMAX9” manually. Read the operating
instructions of the device for details.
Playback during Multi Connect is not working or no
sound.
Restart the app of the device.
The control of the device was not switched successfully.
Disconnect the existing connected devices and try again.
Sound from the device is interrupted.
The device is out of the 10 m communication range. Move
the device nearer to the system.
Remove any obstacle between the system and the device.
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.) are
interfering. Move the device nearer to the system and
distance it from the other devices.
Unit displays
“--:--”
You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
Track play time is more than 99 minutes.
“ADJUST CLOCK”
The clock is not set. Adjust the clock.
“ADJUST TIMER”
The play timer is not set. Adjust the play timer.
“AUDIO UNSUPPORTED”
The signal format or frequency is not supported.
This system does not support bitstream signals. Change the
digital audio output setting on the external equipment to
PCM.
This system supports sampling frequencies of 32 kHz,
44.1 kHz, 48 kHz, up to 96 kHz. Select only the supported
sampling frequencies on the connected equipment.
Try connecting the external equipment by using the auxiliary
input.
“AUTO OFF”
The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
“DEVICE CONNECTED FULL”
You have connected 3 Bluetooth
®
devices. To connect
another device, disconnect one of the connected devices
and try again.
“ERROR”
An incorrect operation was done. Read the instructions and
try again.
“F” / “F” (“” represents a number.)
The protection circuit has been activated and the system
may be switched off automatically.
Disconnect the AC mains lead and wait for a few seconds
before connecting it again. If the problem persists,
disconnect the AC mains lead and consult your dealer.
“NO DISC”
You have not put in a disc.
“NO PLAY”
“UNSUPPORT”
There is no album or track in the USB device.
Examine the content. You can only play supported format.
The files in the USB device can be corrupted. Format the
USB device and try again.
The system may have a problem. Switch off the system and
then switch on again.
“NOT SUPPORT MULTI CONNECT”
The Bluetooth
®
connection cannot be established.
Disconnect the existing connected devices and try again.
“NOT SUPPORTED”
To use Karaoke effect in D-IN source, change the digital
audio output setting on the external equipment to PCM.
“PLAYERROR”
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
“REMOTE 1”
“REMOTE 2”
The remote control and the unit are using different codes.
Change the code of the remote control.
– When “REMOTE 1” is shown, press and hold [OK] and
[ ] on the remote control for a minimum of 4 seconds.
– When “REMOTE 2” is shown, press and hold [OK] and [<]
for a minimum of 4 seconds.
“USB NO DEVICE”
The USB device is not connected. Examine the connection.
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 15 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
16
TQBJ2212
16
“USB OVER CURRENT ERROR”
The USB device is drawing too much power. Disconnect the
USB device, switch off the system and then switch on again.
Check the connection, it may be caused by a faulty USB
cable.
“VBR”
The system cannot show the remaining play time for variable
bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
Preparation
Press [SELECT] repeatedly on the unit to select “AUX”.
To set the code to “REMOTE 2”
1 Press and hold [SELECT] on the unit and [<] until
“REMOTE 2” is shown.
2 Press and hold [OK] and [<] for a minimum of
4 seconds.
To set the code to “REMOTE 1”
1 Press and hold [SELECT] on the unit and [ ] on
the remote control until “REMOTE 1” is shown.
2 Press and hold [OK] and [ ] on the remote
control for a minimum of 4 seconds.
System memory reset
Reset the memory when the following situations occur:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
1 Press and hold [1] on the unit until “RESET?” is
shown.
2 While you press and hold [1] on the unit, press
[SELECT].
“RESET” is shown.
After ––––––––– is shown, the unit will switch
off automatically.
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
DEMO play
The unit will play built-in demonstration song for 1 minute.
1 Press and hold for more than 2 seconds.
“WAIT FOR DEMO PLAY” is shown while you press
and hold the button.
Demonstration song is played and “DEMOPLAY” is
shown.
2 Press [8] to stop the demonstration song.
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 16 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
17
TQBJ2212
17
Specifications
General
Dimensions (W x H x D) 285 mm x 585 mm x 303 mm
Mass 10.2 kg
Operating temperature range 0°C to +40°C
Operating humidity range
35% to 80% RH (no condensation)
Amplifier section
RMS output power (AC Power supply)
Front Ch (both ch driven)
150 W per channel (3 Ω), 1 kHz, 30% THD
Total RMS power 300 W
Disc section
Disc played (8 cm or 12 cm)
CD, CD-R/RW (CD-DA, MP3 )
MPEG-1 Layer 3
Pick up
Wavelength 790 nm (CD)
NORSK
Bølgelengde 790 nm (CD)
Laserstyrke Ingen farlig stråling sendes ut
Terminal section
USB port
USB standard USB 2.0 full speed
Media file format support MP3 (*.mp3)
USB device file system FAT12, FAT16, FAT32
Digital audio input
Optical digital input Optical terminal
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz, 96 kHz
Audio format PCM
Microphone
Terminal Mono, 6.3 mm jack (2 system)
Analog audio input
Audio input Pin jack (1 system)
DC IN
Terminal type USB Micro-B, 5 V, 2 A
Bluetooth
®
section
Version Bluetooth
®
Ver. 5.0
Class Class 1
Supported profiles A2DP, AVRCP, SPP
Frequency band 2.4 GHz band FH-SS
Operating frequency 2402 MHz to 2480 MHz
Maximum power (EIRP) 8 dBm
Operation distance 30 m line of sight
Supported codec SBC
Speaker section
Speaker unit(s)
Woofer 20 cm cone type x 1
Tweeter 6 cm cone type x 2
Note:
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Total harmonic distortion is measured by the digital spectrum
analyser.
Power supply AC 220 V to 240 V, 50 Hz
Power consumption 47 W
Power consumption in standby mode (approximate)
With “BLUETOOTH STANDBY” set to “OFF” 0.5 W
With “BLUETOOTH STANDBY” set to “ON” 0.6 W
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 17 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
18
TQBJ2212
18
English
Declaration of Conformity (DoC)
Hereby, “Panasonic Corporation” declares that this
product is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU.
Customers can download a copy of the original DoC to
our RE products from our DoC server:
http://www.ptc.panasonic.eu
Contact to Authorised Representative:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Germany
Latviski
Atbilstības deklarācija (DoC)
Ar šo “Panasonic Corporation” paziņo, ka šis izstrādājums
atbilst pamatprasībām un pārējiem Direktīvas 2014/53/ES
noteikumiem.
Pircēji var lejupielādēt oriģinālo DoC kopiju mūsu RE
izstrādājumos no mūsu DoC servera:
http://www.ptc.panasonic.eu
Lūdzam sazināties ar pilnvaroto parstāvi:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Vācijā
Lietuviškai
Atitikties deklaracija (AD)
Bendrovė “Panasonic Corporation” patvirtina, kad šis
gaminys atitinka direktyvos 2014/53/ES esminius
reikalavimus ir kitas taikytinas nuostatas.
Mūsų RE gaminių originalios atitikties deklaracijos kopiją
klientai gali atsisiųsti iš mūsų AD serverio:
http://www.ptc.panasonic.eu
Įgaliotojo atstovo adresas:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Vokietija
Slovensko
Izjava o skladnosti (DoC)
Panasonic Corporation” v tem dokumentu izjavlja, da je
izdelek v skladu z bistvenimi zahtevami in drugimi
pomembnimi določbami Direktive 2014/53/EU.
Stranka lahko naloži izvod izvirnega DoC o naših izdelkih
RE s strežnika DoC:
http://www.ptc.panasonic.eu
Naslov pooblaščenega predstavnika:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Nemčija
Slovensky
Vyhlásenie o zhode (DoC)
Panasonic Corporation týmto vyhlasuje, že tento
výrobok je v súlade so základnými požiadavkami a
ďalšími príslušnými ustanoveniami smernice 2014/53/EÚ.
Zákazníci si môžu stiahnuť kópiu pôvodného DoC na
naše RE výrobky z nášho servera DoC:
http://www.ptc.panasonic.eu
Kontakt na splnomocneného zástupcu:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Nemecko
Magyar
Megfelelőségi Nyilatkozat (DoC)
Ezennel a,Panasonic Corporation” kijelenti, hogy a jelen
termék kielégíti az 2014/53/EU Irányelv létfontosságú
követelményeit és más vonatkozó rendelkezéseit.
A vásárlók letölthetik az RE termékek eredeti DoC
másolatát a DoC szerverünkről:
http://www.ptc.panasonic.eu
A hivatalos képviselő elérhetősége:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Németország
Type of wireless Frequency band
Maximum power
(dBm E.I.R.P.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Bezvadu tips Frekvenču josla
Maksimālā jauda
(dBm EIRP)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Bevielio ryšio
tinklas
Dažnių
diapazonas
Maksimali
siuntimo galia
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Vrsta brezžične
povezave
Frekvenčni pas
Največja moč
(dBm EIRP)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Typ bezdrôtového
pripojenia
Frekvenč
pásmo
Maximálny výkon
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Wireless típus Frekvenciasáv
Maximális
teljesítmény
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 18 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
19
TQBJ2212
19
Ελληνικά
Δήλωση συμμόρφωσης (DoC)
H “Panasonic Corporation” δηλώνει ότι το προϊόν αυτό
είναι συμμορφωμένο προς τις βασικές απαιτήσεις και
άλλες σχετικές διατάξεις της Οδηγίας 2014/53/EΕ.
Οι πελάτες μπορούν να κατεβάσουν ένα αντίγραφο του
πρωτοτύπου DoC για τα RE προϊόντα μας από τον DoC
server μας:
http://www.ptc.panasonic.eu
Επικοινωνήστε με τον Εξουσιοδοτημένο Αντιπροσωπό μας:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Γερμανία
Português
Declaração de Conformidade (DoC)
Com o presente documento, aPanasonic Corporation
declara que este produto se encontra em conformidade
com os requisitos específicos e demais especificações
referentes à Diretiva 2014/53/UE.
Os clientes podem baixar uma cópia da declaração de
conformidade (DoC) para nossos produtos RE do Server
DoC:
http://www.ptc.panasonic.eu
Contacto com um Representante Autorizado:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Alemanha
Eesti keel
Vastavusdeklaratsioon (DoC)
Käesolevaga kinnitab “Panasonic Corporation”, et see
toode vastab direktiivi 2014/53/EL olulistele nõuetele ja
teistele asjakohastele sätetele.
Kliendid saavad koopia meie RE toodetele kehtiva
originaalvastavusdeklaratsiooni koopia alla laadida meie
DoC-serverist:
http://www.ptc.panasonic.eu
Võtke ühendust volitatud esindajaga:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Saksamaa
Norsk
Samsvarserklæring (DoC)
Panasonic Corporation” erklærer herved at dette
produktet samsvarer med de grunnleggende kravene og
andre relevante bestemmelser i direktivet 2014/53/EU.
Kundene kan laste ned en kopi av den originale
samsvarserklæringen (DoC) for vårt RE utstyr fra vår DoC
server:
http://www.ptc.panasonic.eu
Kontaktinformasjon autorisert representant:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Tyskland
Български
Декларация за съответствие (DoC)
С настоящото “Panasonic Corporation” декларира, че
този продукт е в съответствие с основните изисквания
и други съответни разпоредби на Директива
2014/53/EС.
Потребителите могат да свалят копие от оригиналните
DoC към нашите продуктите от типа RE от сървъра, на
който се съхраняват DoC:
http://www.ptc.panasonic.eu
Свържете се с нашия упълномощен представител:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Германия
Român
Declaraţie de Conformitate (DoC)
Panasonic Corporation” declară prin prezenta că acest
produs este conform cu cerinţele esenţiale şi alte
prevederi relevante ale Directivei 2014/53/UE.
Clienţii pot descărca o copie a DoC-ului original al
produselor noastre RE de la adressa noastră DoC din
Internet:
http://www.ptc.panasonic.eu
Contactaţi Reprezentantul Autorizat:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Germania
Τύπο ασύρματης
Ζώνη
συχνοτήτων
Μέγιστη ισχύς
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Tipo de ligação
sem fios
Banda de
frequência
Potência
máxima
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Juhtmevaba
seadme tüüp
Sagedusriba
Maksimaalne
võimsus
(dBm EIRP)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Type trådløs Frekvensbånd
Maks. effekt
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Вид безжична
връзка
Честотна лента
Максимална
мощност
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Tip de wireless
Interval de
frecvenţă
Putere
maximă
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
ENGLISH
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 19 Tuesday, November 26, 2019 1:55 PM
offset printing
Confidential
Until:
06 Dec 2019
20
TQBJ2212
20
Hrvatski
Deklaracija o podobnosti (DoC)
Ovime Panasonic Corporationizjavljuje da ovaj proizvod
udovoljava osnovnim zahtjevima i ostalim relevantnim
odredbama Direktive 2014/53/EU.
Kupci mogu preuzeti kopiju originalne DoC za naše RE
proizvode s našeg DoC poslužitelja:
http://www.ptc.panasonic.eu
Adresa ovlaštenog predstavništva:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Njemačka
Türkçe
Uygunluk Beyanı (DoC)
Panasonic Corporation” bu belge ile bu ürünün
2014/53/EU Direkti’nin temel gerekliliklerine ve diğer ilgili
hükümlerine uygun olduğunu beyan eder.
Müşterilerimiz RE ürünlerimizle ilgili orijinal DoC
belgesinin bir kopyasını DoC sunucumuzdan indirebilir:
http://www.ptc.panasonic.eu
Yetkili Temsilci ile temasa geçin:
Panasonic Marketing Europe GmbH, Panasonic Testing
Centre, Winsbergring 15, 22525 Hamburg, Almanya
Vrsta bežične
mreže
Frekvencijski
pojas
Maksimalna
snaga
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
Kablosuz türü Frekans bandı
Maksimum güç
(dBm e.i.r.p.)
Bluetooth
®
2402 – 2480 MHz 8 dBm
TMAX9EG_TQBJ2212_En.Sw.Da.Fi.Po.Cz.book Page 20 Tuesday, November 26, 2019 1:55 PM
offset printing
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Panasonic SCTMAX9EG Käyttö ohjeet

Tyyppi
Käyttö ohjeet