Yamaha CDC-697 Omistajan opas

Kategoria
CD players
Tyyppi
Omistajan opas
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
G
CDC-697
COMPACT DISC AUTOMATIC CHANGER
CHANGEUR AUTOMATIQUE DE DISQUE AUDIONUMÉRIQUE
CDC-697
WH52620
Printed in Malaysia
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
© 2006 All rights reserved.
Getting Started
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
20 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must
be set for your local main voltage BEFORE plugging into the AC
wall outlet. Voltages are 110/120/220/230–240 V AC, 50/60 Hz.
Caution for moving this unit
•When moving this unit, first remove all discs from the disc tray
and close the try by pressing the OPEN/CLOSE button, and
then switch off the power after you confirm that the front panel
display indicates as follows.
Never switch off the power if the front panel display is not
pictured as above, otherwise the unit will break down during
moving because the internal mechanism is not locked.
This unit is not disconnected from the AC power source as long
as it is connected to the wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.
DANGER
When this unit is plugged to the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note:
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED. Making sure that neither core is connected to
the earth terminal of the three pin plug.
1To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2
Install this sound system in a well ventilated, cool, dry, clean place
with at least 10 cm on the top, 10 cm on the left and right, and 10
cm at the back of CDC-697 — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
- Other components, as they may cause damage and/or
discoloration on the surface of this unit.
- Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
- Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of
this unit with a voltage other than specified.
13 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
14 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
15 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
16 Before moving this unit, press POWER ON/OFF to release it
outward to the OFF position to turn off this unit, and then
disconnect the power cable from the AC wall outlet.
17 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
18 When using the unit for a long time, the unit may become
warm. Turn the power off, then leave the unit alone for cooling.
19 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
i
En
2345
01_En_01_cau_CDC-697_G.pm 7/6/06, 0:552
English
GETTING STARTED
PLAYING CDS
FUNCTIONS FOR
RECORDING
ADDITIONAL
INFORMATION
1
En
ENGLISH
Features
5-Discs Carousel Auto-changer
Full Opening Disc Tray for Changing 5 Discs at a Time
PLAYXCHANGE; Disc Changing Capability while Playing back Another
Repeat, Random and Program Play
Remote Control Capability
Introduction
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
Contents
GETTING STARTED
CD PREVENTIVE CARES .................... 2
PREPARATIONS ............................. 3
Supplied Accessories .......................................... 3
Remote Control Transmitter ................................ 3
Connecting to an Amplifier .................................. 4
Connecting the AC power cable .......................... 5
CONTROLS AND FUNCTIONS ............. 6
Front Panel .......................................................... 6
Remote Control Transmitter ................................ 7
Display ................................................................ 8
PLAYING CDS
BASIC OPERATION .......................... 9
Turning On and Off the Power ............................. 9
Loading and Playing Discs .................................. 9
PLAYXCHANGE ................................................. 10
Scanning Discs ................................................. 10
Skipping Tracks ................................................. 11
Searching .......................................................... 11
CD TEXT ............................................................ 11
VARIOUS FUNCTIONS ..................... 12
Random Sequence Play .................................... 12
Program Play .................................................... 13
Repeat Play ....................................................... 15
Index Search ..................................................... 15
Adjusting the Level............................................ 16
Timer Play ......................................................... 16
FUNCTIONS FOR RECORDING
CD SYNCHRONIZED RECORDING ........ 17
TRACK PROGRAMMING
FOR RECORDING...........................
18
Automatic Tape Programming........................... 18
Manual Tape Programming ............................... 19
Random Tape Programming ............................. 21
AUTOMATIC PEAK LEVEL SEARCHING ....
22
ADDITIONAL INFORMATION
TROUBLESHOOTING ....................... 23
SPECIFICATIONS ........................... 24
01_En_02_star_CDC-697_G.pm 7/13/06, 12:191
2
En
This compact disc player is designed only for playing
back compact discs bearing the marks shown below.
Never attempt to load any other type of disc into the unit.
The unit can also play back 8 cm (3 inch) compact discs.
Notes
•This unit may not be able to play back some CD-R/CD-RW
discs or discs on which recording was not made correctly.
•This unit is not compatible with a CD-R/CD-RW disc
recorded with MP3 or WMA format.
Compact discs are not subjected to wear during
playback, but damage to the disc surface when the disc is
being handled can adversely affect the disc playback.
Do not use cleaning discs or warped discs. All of these
could damage the unit.
To prevent a malfunction of this unit
Do not use any non standard shaped CD (heart, etc.)
available on the market, because it may damage the unit.
Do not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
Compact discs are not affected by small particles of dust
or fingerprints on their playing surface, but even so they
should be kept clean. Wipe by using a clean, dry cloth.
Do not wipe with a circular motion; wipe straight
outward from the center.
Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, anti-static spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the disc’s surface.
Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time, because these
might warp or otherwise damage the disc.
CD PREVENTIVE CARES
No!
01_En_02_star_CDC-697_G.pm 7/6/06, 0:552
3
En
GETTING STARTED
English
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control transmitter will not
be used for an extended period of time.
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
PREPARATIONS
Supplied Accessories
Remote Control Transmitter
Remote control transmitter
operation range
Notes
•There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
2
1
3
NATURAL SOUND COMPACT DISC PLAYER CDC-697
DISC
12345
STANDBY
/ON
POWER
ON OFF
PLAYXCHANGE
30°
30°
Remote control sensor
Within approximately
6 m (19.7 feet)
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
Remote Control Transmitter Batteries (AA, R6, UM-3) x 2
Audio Pin Cable
Power cable
(U.S.A., Canada, Australia, U.K. and
Europe models) The shape of the
plug may vary depending on the area
where you purchased.
01_En_02_star_CDC-697_G.pm 7/6/06, 0:553
4
En
Connecting an Amplifier
Never plug in this unit and other components until all connections are completed.
Before making any connections, switch OFF the power to the unit and the amplifier or other components.
Connections should be made to the correct input terminals of the amplifier or other components.
If the placement of this unit causes noise in other equipment, such as a tuner, separate them from each other.
Choose one of the ways listed below to connect this unit to your amplifier.
When the LINE OUT (analog) terminals of this unit are used (1)
Be sure that the left (L) and right (R) LINE OUT terminals are connected to the corresponding (left and right) terminals of
the amplifier or other components.
Connect the LINE OUT terminals to the CD (or AUX) terminals of the amplifier. For additional details concerning these
connections, refer to the operation instructions for the amplifier being used.
When the DIGITAL AUDIO OUT (OPTICAL) terminal of this unit is used (2)
Before using this terminal, remove the terminal cover by pulling it.
Make the connection from this terminal to the optical input terminal of an amplifier by using a commercially available
optical cable.
* Be sure to use a high quality optical fiber cable. Other cables might not function correctly.
Be sure to attach the terminal cover when this terminal is not being used in order to protect the terminal from dust.
Set the level of signals output into an amplifier to max by using the OUTPUT LEVEL –/+ buttons.
For Custom Installer
REMOTE CONTROL IN/OUT terminals
These terminals are used for custom installation system. When this unit is connected to the components for custom
installation system, you can operate this unit with the system remote control.
Connect the REMOTE CONTROL IN terminal of this unit to the output terminal of the central controller for custom
installation system.
By connecting the REMOTE CONTROL OUT terminal of this unit to the REMOTE CONTROL IN terminal of the
other component, you can also operate it with the system remote control. In this way, up to 6 components can be
connected in series.
RS-232C terminal
This terminal dose not support normal external component connection. This is an expansion terminal for factory use
only.
LINE OUT
RS-232C
DIGITAL AUDIO OUT
OPTICAL
OUTIN
REMOTE CONTROL
VOLTAGE SELECTOR
230-
240V
R L
DIGITAL IN
ANALOG IN
CD
OPTICAL
R
L
R L
LINE OUT
DIGITAL AUDIO OUT
OPTICAL
PREPARATIONS
REMOTE CONTROL IN/OUT terminals
2 Optical cable
(not included)
1 Audio pin cable
(included)
Amplifier
RS-232C terminal
(General model)
01_En_02_star_CDC-697_G.pm 7/6/06, 0:554
5
En
GETTING STARTED
English
Connecting the power cable
After all other connections are completed, plug the power cable to an AC wall outlet.
VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the
AC main supply. Voltages are AC 110/120/220/230–240 V, 50/60 Hz.
AC IN
China, Asia and General models
Other models
Plug the power cable into the AC IN, then plug the power
cable to an AC wall outlet.
To AC wall outlet
To AC wall outlet
VOLTAGE SELECTOR
230-
240V
PREPARATIONS
01_En_02_star_CDC-697_G.pm 7/6/06, 0:555
6
En
CONTROLS AND FUNCTIONS
Front Panel
NATURAL SOUND COMPACT DISC PLAYER CDC-697
DISC
12345
STANDBY
/ON
POWER
ON OFF
231
45 6789
0qw
PLAYXCHANGE
7 Remote control sensor ....................................... P.3
8 t/e (Skip/Search) ...................................... P.11
9 r/y (Skip/Search) ...................................... P.11
0 w/d (Play/Pause) ............................................. P.10
q a (Stop) ........................................................... P.10
w PLAYXCHANGE ........................................... P.10
1 POWER ............................................................ P.9
2 Disc tray ............................................................. P.9
3 f (Open/Close) ..................................................P.9
4 STANDBY/ON ................................................. P.9
5 DISC-select ..................................................... P.10
6 Display panel ..................................................... P.8
01_En_02_star_CDC-697_G.pm 7/6/06, 0:556
7
En
GETTING STARTED
English
Remote Control Transmitter
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
1
2
3
4
5
6
7
8
9
0
q
w
t
y
u
i
o
p
a
s
d
e
f
r
1 STANDBY/ON ................................................. P.9
2 SYNCHRO ..................................................... P.17
3 DIMMER ........................................................... P.8
4 TEXT/TIME ....................................................... P.8
5 TAPE ............................................................... P.18
6 Numeric buttons ............................................... P.11
7 Disc play MODE-select ..................................... P.9
8 DISC SCAN ................................................... P.10
9 d (Pause) .......................................................... P.10
0 REPEAT.......................................................... P.15
q w (Play) ............................................................ P.10
w t (Skip) ......................................................... P.11
e a (Stop) ........................................................... P.10
r e (Search) ..................................................... P.11
t OPEN/CLOSE ................................................. P.9
y PEAK .............................................................. P.22
u PROG .............................................................. P.13
i CLEAR ............................................................ P.14
o INDEX ............................................................. P.15
p OUTPUT LEVEL –/+ .................................... P.16
a DISC SKIP ..................................................... P.10
s RANDOM ....................................................... P.12
d y (Skip) ......................................................... P.11
f r (Search) ..................................................... P.11
CONTROLS AND FUNCTIONS
01_En_02_star_CDC-697_G.pm 7/6/06, 0:557
8
En
The display located in the center of this unit provides
information about discs.
After closing the disc tray by pressing the OPEN/CLOSE
button or selecting any disc by using the DISC SKIP
buttons when this unit is stopped, the display shows the total
number of tracks and the total recorded time of the selected
disc for a few seconds.
Display information at disc playback
1 Encloses the tray number of the selected disc.
2 The numbers corresponding to trays that contain discs
light up after discs are selected.
3 Shows the selected track number.
4 Shows the time displays. (For details, refer to “Selecting
time displays and the text data” on the right column.)
5 Displays the numbers that correspond to the numbers of
the tracks (as high as number 20) on the selected disc.
After each track is played back, its corresponding
number disappears so the number of remaining tracks
(and their numbers) can be seen at a glance.
6 Shows the level of signals output into an amplifier
adjusted by using the OUTPUT LEVEL –/+ buttons.
Changing brightness of the display
If desired, you can change brightness of the display in three
degrees by pressing the DIMMER button.
1 Elapsed time of the track now playing back
2 2:35
1 2345
5DISCS
2345
678 910
11 12
2- 1:02
1 2345
5DISCS
2345
678 910
11 12
TOTAL -32:27
1 2345
5DISCS
2345
678 910
11 12
TOTAL 38:14
1 2345
5DISCS
2345
678 910
11 12
CONTROLS AND FUNCTIONS
Display
Notes
The remaining time 2 will not be displayed if the track
number is 21 or higher.
The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case,
“NO ENTRY” appears in the display.
when playing back a disc without CD TEXT
2 Remaining time of the track now playing back
3 Total disc playback time
4 Total remaining time on the disc
Selecting time displays and the text
data
You can select any of the four time displays by pressing the
TEXT/TIME display mode-select button. Since this unit is
CD TEXT compatible, the disc title, artist name, and track
name are also displayed in addition to the time displays
when playing back a CD with CD TEXT. Each time you
press the TEXT/TIME display mode-select button, the
display changes as follows.
12 53:38
12345
5DISCS
123 4 5
678 910
11 12
3 0:08
1 2345
5DISCS
345
678 910
11 12
12 5
643
DIMMER
Disc title
Artist name
Track name
when playing back a CD TEXT disc
TEXT/
TIME
01_En_02_star_CDC-697_G.pm 7/6/06, 0:558
English
PLAYING CDS
9
En
2 Close the disc tray.
•You can also close the disc tray by pressing the w/d
button on the front panel, a DISC-select button on
the front panel, a numeric button or the RANDOM
button, or by pressing the front edge of the disc tray
gently. If the tray is closed in these ways, playback
will start automatically, however, the display will not
show the total number of tracks and the total
recorded time of the first selected disc.
Loading and Playing Discs
1 Open the disc tray and load discs.
Use the disc guides to align the discs correctly in the
tray.
To play back an 8 cm (3 inch) CD, place it in the inner
recessed area of the disc tray. Do not put a normal
(12 cm (5 inch)) CD on top of an 8 cm CD.
This manual describes how to operate this unit by using the
remote control transmitter.
To operate this unit on the front panel, use the
corresponding buttons on the front panel.
Turning On and Off the Power
To turn on this unit
Press the POWER button inward to the ON position.
•Press the STANDBY/ON button to set this unit to
the standby mode.
•Press the STANDBY/ON button to turn on this unit.
Note
You can operate this unit only when the POWER button is
pressed inward to the ON position.
To turn off this unit
Press the POWER button again to release it outward to the
OFF position.
BASIC OPERATION
OPEN/
CLOSE
On the front panel
Label side upward
Disc tray
OPEN/
CLOSE
POWER
ON OFF
STANDBY
/ON
STANDBY
/ON
STANDBY/ON
STANDBY/ON
On the front panel
On the front panel
On the remote control
transmitter
On the remote control
transmitter
NATURAL SOUND COMPACT DISC PLAYER CDC-697
DISC
1 2345
STANDBY
/ON
POWER
ON OFF
STANDBY/ON
POWER
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
OPEN/
CLOSE
TEXT/
TIME
PLAYXCHANGE
POWER
ON OFF
On the front panel
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
1,2
3
4
4
01_En_03_play_CDC-697_G.pm 7/6/06, 0:559
10
En
To stop playback temporarily
To resume playback, press the d button again (or press the
w button).
*The w/d button on the front panel can also be used to
stop playback temporarily or to resume playback.
To stop playback completely
PLAYXCHANGE
During playback, you can open the disc tray by pressing the
PLAYXCHANGE button on the front panel without
interrupting disc playback. However, in this case, pressing
the DISC SKIP buttons has no effect. You can load or
replace discs on the trays when the disc tray is opening,
however, never load a disc on the tray hidden inside the unit.
If doing so, the disc and the unit may be damaged, because
the tray already has a disc, which is being played back.
Scanning Discs
This mode is convenient to search
for a desired disc (or to check discs
on the disc tray)
When the DISC SCAN button is pressed in stop mode, this
unit will play back a section of each disc in turn for 8
seconds.
If, during this playback, you find a disc that you want to
listen to, press the DISC SCAN button once again or press
the w button to cancel this function. The unit will enter into
the normal playback mode.
Notes
During this playback, the disc tray numbers blink in the
display. Every time the playback of a disc is finished, the
corresponding tray number is changed from flashing to
lighting.
If the disc being played back has a long blank space between
tracks, you will hear no sound during disc scan.
or
On the front panel
or
On the front panel
DISC SCAN
3 Select a desired disc play mode (1DISC or
5DISCS) confirming it on the display.
“1DISC” mode: The unit will play back a
designated disc only.
“5DISCS” mode: The unit will play back all discs on
the tray in sequence.
4 Start playback from the first track of the disc 1.
* If necessary, select a desired disc by using the
DISC SKIP buttons, or a DISC-select button on the
front panel.
MODE
SEARCH
1DISC
5DISCS
TITLE
REP R
N
SF
P
ARTIS
T
DISC SKIP
23
DISC
4
On the front panel
or
Shows the selected disc mode.
Playback will automatically
start.
On the remote control
transmitter
On the remote control
transmitter
On the remote control
transmitter
BASIC OPERATION
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5510
English
PLAYING CDS
11
En
Skipping Tracks
To play back from the beginning of
the track following the one now
playing back
To play back from the beginning of
the track now playing back
To play back from the beginning of
the track before the one now
playing back
These operations can also be performed when the unit is
paused or stopped.
•When using the t or y button on the remote control
transmitter:
* If the button is pressed and held, the track number is
continuously changed to higher numbers (or lower
numbers).
DIRECT PLAY
Select a desired track by using the numeric buttons.
Example: To select track 25
Press +10 twice, then immediately press 5 once.
* If a track number higher than the highest track number
on the disc is selected, the last track on the disc will be
played back.
Searching
To go forward rapidly
To go backward rapidly
•The sound can be heard (although slightly garbled)
during manual search in either direction. This is
convenient for locating a precise position within a track,
or for reviewing the contents quickly.
Manual search can also be performed while disc
playback is paused. In this case, no sound will be heard.
CD TEXT
This unit is compatible with the CD TEXT function. The
CD TEXT disc has information, such as the disc title, artist
names, and track names. If the current disc is a CD TEXT
disc, the unit reads the disc title, artist name, and track
names from the disc. You can display the CD TEXT data
(see “Selecting time displays and the text data” on page 8).
(Twice)
5
1 2 3 4 5
SEARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST EDIT FILE
SFPROG CD- TEXT
ARTIST TRACK
123 4 5
678 910
11 12 13 14 15
16 17 18 19
The selected track number is displayed.
(Press and hold.)
(Press and hold.)
32
1
65
4
98
7
10
0
BASIC OPERATION
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5511
12
En
VARIOUS FUNCTIONS
Random Sequence Play
You can play back the tracks on one or more discs in a
random sequence. The unit will automatically mix up tracks
from all discs or a designated disc on the disc tray.
1 Load one or more discs.
2 Close the disc tray.
3 Select a desired disc play mode (1DISC or
5DISCS).
* If you select “1DISC” mode, next select a desired
disc by using the DISC SKIP buttons on the remote
control transmitter or a DISC-select button on the
front panel.
4 Press the RANDOM button.
“RNDM” lights up in the display.
To cancel random-sequence play
Press the a button or RANDOM button once again, or open
the disc tray by pressing the OPEN/CLOSE button.
“RNDM” disappears from the display.
Notes
This feature will not function during programming, or during
program play.
If the y button is pressed during random-sequence play, the
next randomly programmed track will be played back. If the
t button is pressed, playback will return to the beginning of
the track now being played back.
This indication appears while the unit is mixing up tracks.
•Total remaining time on the disc will not be displayed during
random-sequence play.
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
1,2
3
4
OPEN/
CLOSE
OPEN/
CLOSE
MODE
RANDOM
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5512
English
PLAYING CDS
13
En
Program Play
You can enjoy listening to your favorite tracks selected from
one or more discs in any desired order by programming
tracks.
1 Stop the unit.
2 If you will select tracks from a disc (or discs)
other than the disc on the Disc 1 tray, make this
unit display the total recorded time of each disc
to be used by pressing the DISC SKIP buttons
in turn.
*Without this operation, the total time of the
programmed tracks will not be displayed during
programming.
3 Press the PROG button to start programming.
4 If necessary, select a desired disc.
5 Program a desired track by pressing the
corresponding numeric button.
6 Repeat steps 4 and 5 to program more tracks.
You can select the same track again.
7 When the programming is completed, start the
playback.
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
3
5
2,4
7
1
DISC SKIP
STEP 1
SEARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST EDIT
SFPROG CD- TEXT
ARTIST TRACK
12
67
11 12
16 17
DISC SKIP
or
23
DISC
4
On the front panel
PROG
32
1
65
4
98
7
10
0
On the remote control
transmitter
VARIOUS FUNCTIONS
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5513
14
En
Display information during
programming
1 Shows the program number for the track to be
programmed next.
2 Shows the selected disc and track number.
3 Shows the total time of the tracks currently
programmed.
4 Shows only the numbers of programmed tracks on the
selected disc.
* If “STEP 1” does not appear on the display after the
PROG button is pressed, press the TEXT/TIME display
mode-select button.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
Notes
•You can program as many as 40 tracks at one time.
•You can program a whole disc by pressing “0”, instead of one
track. At that time, “ALL” lights up in the display.
The total time of the programmed tracks will not be
displayed, if a track number higher than 20 is programmed.
If, during programming, the TEXT/TIME display mode-
select button is pressed, the program number display can be
changed to display the total time of the programmed tracks or
no information. To return to the previous display, press the
TEXT/TIME display mode-select button once again.
•The t and y buttons can be used during playback, but
only within the range of the programmed tracks.
•Pressing a numeric button stops the current program and
skips to the beginning of the track of the number pressed.
Once that track has finished playback, the previously
interrupted program resumes playback.
•The e and r buttons can be used during playback to
search all tracks, including unprogrammed tracks.
To stop program play
Press the a button. The first programmed track number will
be displayed.
To resume playback, press the w button. Playback will start
from the beginning of the program.
To cancel a programmed sequence
There are several methods, as described below.
•Press the a button or the CLEAR button while the unit
is stopped.
Open the disc tray.
•Press the STANDBY/ON button.
Switch off the power.
To check program data
1 During program play, press the a button.
2 Press the PROG button.
3 Each time the y button is pressed, the track numbers
and sequential order of the programmed tracks can be
checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the t button.
To correct program data
1 Follow the procedure described in “To check program
data”.
2 Display the track number to be corrected by pressing the
t or y button.
3 Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4 After the correction has been completed, press the
PROG button or w button once again.
-- STEP 1
1 2 3 4 5
SEARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST EDIT FILE
SFPROG CD- TEXT
ARTIST TRACK
123 4 5
678 910
11 12 13 14 15
16 17 18 19 20
1
-6 STE 3:25
1 2 3 4 5
SEARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST EDIT FILE
SFPROG CD- TEXT
ARTIST TRACK
123 4 5
6 789
11 12 13 14 15
16 17 18 19 20
3
4
2
VARIOUS FUNCTIONS
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5514
English
PLAYING CDS
15
En
Repeat Play
You can play back any desired track or disc (or a set of
discs) repeatedly by pressing the REPEAT button. The
repeat play mode will change whenever you press the
REPEAT button.
REP S (Single repeat)
A single track is repeatedly played back.
*This is also available in the program play mode and the
random-sequence play mode. (If the repeat play mode is
switched off, the program play mode or the random-
sequence play mode will be resumed.)
REP F (Full repeat)
In the “1DISC” disc play mode: A designated disc is
repeatedly played back.
In the “5DISCS” disc play mode: All discs on the disc tray
are repeatedly played back.
* In the program play mode, all programmed tracks are
repeatedly played back.
* In the random-sequence play mode, all randomly
sequenced tracks on a designated disc (1DISC) in the
same order, or all randomly sequenced discs and tracks
(5DISCS) are repeatedly played back.
Index Search
If the disc includes index numbers, playback can be started
from any desired index number.
1 Select a track which has index numbers.
2 Press the INDEX button.
3 Select the desired index number.
To cancel the index search function
Press the INDEX button.
Notes
Not all discs have index numbers. The index system has a
method for sub-dividing tracks into smaller divisions (for
example, the movements within classical symphonies) for
easier location of those parts. The liner notes with the disc
usually tell if such index numbers are included.
If an index number is selected that is higher than any index
number on that disc, playback will start from the last index
number point on the disc.
•For some discs, playback may start slightly prior to the actual
designated index point.
If the disc has no encoded index points, playback will start
from the beginning of the selected track.
RCH
1DISC
5DISCS
TITLE
REP RNDM S
A
S F PROG
C
ARTIST TRAC
RCH
1DISC
5DISCS
TITLE
REP RNDM S
A
S F PROG
C
ARTIST TRAC
REPEAT
32
1
65
4
98
7
10
0
INDEX
IDX 3
S
EARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST
SFPROG CD- TEXT
ARTIST TRACK
13 14 15
16
17 18 19 20
5 INDEX 1
1 2 3 4 5
SEARCH
1DISC
5DISCS
TITLE
REP RNDM SAVE BEST EDIT FILE
SFPROG CD- TEXT
ARTIST TRACK
123 4 5
678 910
11
12
3
(Off)
VARIOUS FUNCTIONS
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5515
16
En
Timer Play
You can start playback at any specified time by connecting a
timer (sold separately). (For details, refer to the owner’s
manual of the timer.)
1 Select the desired play mode (1DISC or 5DISCS).
2 Press the POWER button to turn the unit off.
3 Press the POWER button while pressing the w/d button
on the front panel.
Shortly thereafter, “TIMER P. ON” appears in the
display and the timer play function is on.
(When the timer play function is already on, in which
case, “TIMER P. OFF” appears in the display and timer
play function is off. In this case, repeat the procedure in
steps 2 and 3 to set the timer play function to on.)
4 Set the timer to the desired time.
When the set time comes, the unit turns on and starts
playback.
Adjusting the Level
Adjusting the level of signals output
into an amplifier, etc.
You can adjust the level of sound signals output from the
LINE OUT terminals on the rear panel into an amplifier,
etc.
For optimum sound quality
*When the DIGITAL AUDIO OUT (OPTICAL) terminal
is used for the connection, set the level of output signals
to max.
*The level of output signals can be checked in the display.
OUTPUT LEVEL
——
CK
678910
11 12 13 14 15
16 17 18 19 20
NATURAL SOUND COMPACT DISC PLAYER CDC-697
DISC
1 2345
STANDBY
/ON
POWER
ON OFF
2,3 3
PLAYXCHANGE
VARIOUS FUNCTIONS
01_En_03_play_CDC-697_G.pm 7/6/06, 0:5516
English
FUNCTIONS FOR
RECORDING
17
En
CD SYNCHRONIZED RECORDING
Using a compatible YAMAHA tape deck, you can
synchronize the tape deck to start recording automatically
when this unit starts playback. With this function, you can
record a CD on tape more easily and precisely. (For details,
refer to the operation manual of the tape deck to know
whether it is compatible or not.)
* This unit and the tape deck must be placed close to each
other so that both of them can receive the signals from the
remote control transmitter of this unit at the same time.
1 Select a disc.
2 Load a tape on the tape deck.
*The peak level searching function of this unit is
useful for adjusting recording level on the tape deck.
(For details, refer to page 22.)
3 Press the SYNCHRO button.
This unit enters into the pause mode, and the tape deck
enters into the REC/PAUSE mode.
* In this mode, the time display on this unit blinks.
4 If desired, select the track to be recorded first.
5 Press the w button.
Both CD playback and tape deck recording start.
* CD playback starts a little later than recording.
6 If you want to stop recording temporarily and
restart recording from a desired track, follow
steps 3 to 5 again.
To cancel this function
Press the a button.
Notes
•To finish or stop recording, press the a button on the tape
deck.
Programmed sequence of tracks can also be recorded with
this function, instead of recording an entire disc. (For details,
refer to pages 13 to 14.)
This function can also be used together with the tape-
programming function. (For details, refer to pages 18 to 21.)
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
4
3
1
5
DISC SKIP
SYNCHRO
DISC SKIP
or
32
1
65
4
98
7
10
0
01_En_04_func_CDC-697_G.pm 7/6/06, 0:5617
18
En
You can select any of four tape lengths by pressing the
TAPE button.
You can also enter the total possible recording time of
the tape manually.
Example: For a C-64 tape (32 minutes on each side)
4 Press the REPEAT button.
The unit automatically programs tracks for side A and
side B separately considering the total time of the tape.
* The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
5 Start recording on the tape deck and press the
w button at the same time.
6 The unit will pause at the end of side A of the
tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the w or d button.
Notes
It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
CD synchronized recording function can be used if your tape
deck is compatible with it. In this case, in step 5 and 6, press
the SYNCHRO button and then press the w button.
Recording automatically starts. (For details, refer to page 17.)
TAP E
TRACK PROGRAMMING FOR RECORDING
This convenient feature can be used to program tracks for
recording to tape. By only memorizing the total possible
recording time of the tape, the unit will automatically
program tracks or help you to program tracks so they will fit
onto the tape with the least amount of unrecorded space
remaining at each end of the tape.
The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (For details, refer
to page 22.)
Automatic Tape Programming
The unit will automatically program tracks on a disc with
the original order of tracks unchanged.
1 Stop the unit.
2 Select the disc.
3 Enter the total possible recording time of the
tape (tape length).
DISC SCAN
REPEAT
CDC8
WH26170
RANDOM
DISC SKIP
SYNCHRO
DIMMER
STANDBY/ON
PEAK
PROGCLEARTAPE
321
654
987
INDEX+100
OUTPUT LEVEL
MODE
DISC SCAN
REPEAT
RANDOM
DISC SKIP
+
-
OPEN/
CLOSE
TEXT/
TIME
3
2
5
1
4
DISC SKIP
TAPE
46
64
REPEAT
(Off)
6
1
4
2
01_En_04_func_CDC-697_G.pm 7/6/06, 0:5618
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178

Yamaha CDC-697 Omistajan opas

Kategoria
CD players
Tyyppi
Omistajan opas