Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Manuale di istruzioni
Руководство пользователя
JA
RU
IT
PT
ES
FR
DE
EN
SPEAKER SYSTEM
LOUDSPEAKER
2 CZR series Owner’s Manual
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe place for
future reference.
WARNING
Always follow the basic precautions listed below to
avoid the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other
hazards. These precautions include, but are not limited
to, the following:
If you notice any abnormality
• If any of the following problems occur, immediately turn off
the power of the amplifier.
- Unusual smells or smoke are emitted.
- Some object, or water has been dropped into the product.
- There is a sudden loss of sound during use of the product.
- Cracks or other visible damage appear on the product.
Then have the product inspected or repaired by qualified
Yamaha service personnel.
Do not open
• This product contains no user-serviceable parts. Do not
attempt to disassemble the internal parts or modify them in
any way.
Water warning/Fire warning
• Do not expose the product to rain, use it near water or in
damp or wet conditions, or place on it any containers (such
as vases, bottles or glasses) containing liquids which might
spill into any openings.
• Do not place any burning items or open flames near the
product, since they may cause a fire.
Hearing loss
• When turning on the AC power in your audio system, always
turn on the power amplifier LAST, to avoid hearing loss and
speaker damage. When turning the power off, the power
amplifier should be turned off FIRST for the same reason.
CAUTION
Always follow the basic precautions listed below to
avoid the possibility of physical injury to you or others,
or damage to the product or other property. These
precautions include, but are not limited to, the following:
Location and connection
• Do not place the product in an unstable position where it
might accidentally fall over and cause injuries.
• Keep the device out of reach of children. This product is not
suitable for use in locations where children are likely to be
present.
• Do not place the product in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
• Before moving the product, remove all connected cables.
• When transporting or moving the product, always use two or
more people. Attempting to lift the product by yourself may
damage your back, result in other injury, or cause damage to
the product itself.
• Do not use the speaker’s handles for suspended installation.
Doing so can result in damage or injury.
• Do not hold the bottom of the product when transporting or
moving it. In doing so, you may pinch your hands under the
product, and result in injury.
• Do not press the rear panel of the product against the wall.
Doing so may cause the plug to come in contact with the wall
and detach from the cable, resulting in short circuiting,
malfunction, or even fire.
• Always consult qualified Yamaha service personnel if the
product installation requires construction work, and make
sure to observe the following precautions.
- Choose mounting hardware and an installation location that
can support the weight of the product.
- Avoid locations that are exposed to constant vibration.
- Use the required tools to install the product.
- Inspect the product periodically.
• Use only speaker cables. Use of other types of cables may
result in fire.
Handling caution
• When choosing a power amplifier for use with this product,
make sure that the output power of the amplifier is lower than
the power capacity of this product. If the output power is
higher than the power capacity, malfunction or fire may occur.
• Do not input excessively loud signals that may result in
clipping in the amplifier or cause the following:
- Feedback, when using a microphone
- Continuous and extremely loud sound from a musical
instrument, etc.
- Continuous and excessively loud distorted sound
- Noise caused by plugging/unplugging the cable while the
amplifier is turned on
Even if the output power of the amplifier is lower than the
power capacity of this product (program), damage to the
product, malfunction or fire may occur.
• Do not operate the product if the sound is distorting.
Prolonged use in this condition could cause overheating and
result in fire.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the product.
PA_en_9
CZR series Owner’s Manual 3
NOTICE
To avoid the possibility of malfunction/damage to the product,
or damage to other property, follow the notices below.
Handling and maintenance
• Do not expose the product to excessive dust or vibration,
or extreme cold or heat (such as in direct sunlight, near a
heater, or in a car during the day), in order to prevent the
possibility of panel disfiguration, unstable operation, or
damage to the internal components.
• Do not place the speaker face down with the grille
attached, as deformation of the grille may result.
• When placing the speaker face down, always place it on a
flat surface.
• Do not touch the speaker driver unit.
• Be sure to observe the amplifier’s rated load impedance
(see page 7), particularly when connecting speakers in
parallel. Connecting an impedance load outside the ampli-
fier's rated range can damage the amplifier.
• Protection Circuit
This speaker system has an internal protection circuit that
shuts off the speaker unit when an excessive input signal is
applied. If the speaker unit emits no sound, reduce the vol-
ume level of the amplifier immediately. The sound will
return automatically in several seconds.
• Air blowing out of the bass reflex ports is normal, and often
occurs when the speaker is handling program material
with heavy bass content.
• During extreme changes in temperature or humidity, con-
densation may occur and water may collect on the surface
of the product. If water is left, the wooden parts may
absorb the water and be damaged. Make sure to wipe any
water off immediately with a soft cloth.
Connectors
• Use only Neutrik NL4 plugs for connecting speakON con-
nectors.
Information
About this manual
• The illustrations as shown in this manual are for instruc-
tional purposes only.
• The company names and product names in this manual
are the trademarks or registered trademarks of their
respective companies.
About disposal
• This product contains recyclable components. When dis-
posing of this product, please contact the appropriate
local authorities.
4 CZR series Owner’s Manual
(weee_eu_en_02)
Information for users on collection and disposal of old equipment:
This symbol on the products, packaging, and/or accompanying documents means that used electrical and elec-
tronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in
accordance with your national legislation.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential nega-
tive effects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please contact your local municipality, your
waste disposal service or the point of sale where you purchased the items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for fur
ther informa-
tion.
Information on Disposal in other Countries outside the European Union:
This symbol is only valid in the European Union. If you wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of disposal.
CZR series Owner’s Manual 5
Introduction
Thank you for purchasing the Yamaha CZR15, CZR12, CZR10 LOUDSPEAKER (hereinafter referred to as
“CZR”). This product is a speaker designed for live performance, sound reinforcement and fixed installa-
tion sound system applications. This manual explains how to install, set up, and configure the connec-
tions for the installers, constructors, or general users familiar with speakers. Please read this manual
thoroughly before you begin using this product to get the most out of the product. After reading this man-
ual, please keep it available for future reference.
• The example illustrations used in this manual are taken from the CZR12, if not otherwise specified.
Contents
PRECAUTIONS ..................................................................... 2
Introduction ........................................................................... 5
Main Features........................................................................ 5
Included Accessories............................................................ 5
Optional Accessories (sold separately) ................................ 5
Functions............................................................................... 6
Connection ............................................................................ 7
Selection and Settings of Processors and Amplifiers............8
Basic Setting Example...........................................................8
Rotatable Horn.......................................................................9
Switching Between Passive and Bi-amp Mode...................10
Installation Examples...........................................................11
Troubleshooting ...................................................................13
Specifications (English only) .............................................100
Main Features
• The CZR series has three different models, depending on the woofer size: CZR15 (15-inch), CZR12 (12-inch) and CZR10 (10-
inch).
• The LF (low-frequency) unit features an aluminum die-cast frame and a 3-inch voice coil for high durability in audio reproduc-
tion. It uses a lightweight and powerful neodymium magnet that achieves band extension to even lower frequencies and
reproduction capability that adds punch and power to the bass.
• The HF (high-frequency) unit features a titanium diaphragm, 2-inch voice coil, and neodymium magnet. It is paired with a fixed
directional horn designed specifically for each model, for sparkling highs and superior directional characteristics.
• The specially designed enclosure features lightweight and strong plywood with a scratch-resistant rigid polyurea coating for
improved portability and durability.
• A variety of installation methods are possible, including two angle adjustments for use on a stand, use as a floor monitor, sev-
eral rigging points, and 90-degree rotation of the horn.
• The speaker can be changed to a Bi-amp configuration, to maximize the performance of each unit and further optimize the
reproduction characteristics.
Included Accessories
Owner’s Manual (this book)
Optional Accessories (sold separately)
U-bracket (UB-DZR series) Speaker cover (SPCVR series)
CZR15 UB-DZR15H, UB-DZR15V SPCVR-DZR15
CZR12 UB-DZR12H, UB-DZR12V SPCVR-DZR12
CZR10 UB-DZR10H, UB-DZR10V SPCVR-DZR10
6 CZR series Owner’s Manual
Functions
q Tiltable pole socket
This mount has two pole sockets. You can choose the
angle of the CZR unit so that the speaker is positioned
horizontal to the floor or tilting down toward the floor by 7
degrees. These sockets are compatible with commercially
available speaker stands and speaker poles of 35 mm
diameter.
we [INPUT/PARALLEL] jacks
These are speakON jacks (Neutrik NL4) for connection to
a power amplifier using a speaker cable. The factory set-
ting is in the Passive mode. When using in the Passive
mode, input the signals to the 1+/1– contacts of the
[INPUT/PARALLEL] jack. w and e are connected in par-
allel.
r Screw holes for U-bracket
For installing with separately sold U-brackets.
t Screw holes for eye bolts
For installing the CZR using eye bolts. The screw holes for
eye bolts go through the cabinet wall.
q
we
w
e
rt
Front Rear
Bottom
FRONT
7°
0°
7°
Pole socket
speakON plug
Insert all the way inside
and turn to lock
CZR series Owner’s Manual 7
Connection
Wiring
Wire the plugs as shown below. Make sure to use cables specially designed for speakers. When the CZR itself is used in the
Passive mode, wiring to the 2+ and 2– contacts is unnecessary. When the CZR is used in the Bi-amp mode, or when the signals
are sent together with the signal from a subwoofer over a single cable (see “Basic Setting Example” on page 8), make sure to
also wire to the 2+ and 2– contacts.
Parallel Connection of Speakers
[INPUT/PARALLEL] jacks are connected inside in parallel. The first CZR can receive the signal from a power amplifier (hereinaf-
ter, “amplifier”) by one of the [INPUT/PARALLEL] jacks, and route the signal to the second CZR from the rest of [INPUT/PARAL-
LEL] jacks.
When connecting CZR units in parallel, be sure to check the load impedance that the amplifier can drive with. The nominal
impedance of one CZR is eight ohms, and the total impedance of two parallel CZR units is four ohms. In this case, the amplifier
must be able to drive a speaker less than four ohm load impedance.
Invalid connection
NOTICE
NEVER connect multiple signals from the amplifier to the [INPUT/PARALLEL] jacks simultaneously. This creates a very dangerous
short circuit, possibly resulting in amplifier malfunction.
Passive
(2–: Unused)
Bi-amp
(2+: Unused)
1+:
1–:
1+: LF+
1–: LF–
2+: HF+
2–: HF–
Amplifier
From
amplifier
To next CZR
First CZR
(impedance: 8 Ω)
Second CZR
(impedance: 8 Ω)
Parallel connection (total impedance: 4 Ω)
Amplifier
B channel
A channel
CZR
8 CZR series Owner’s Manual
Selection and Settings of Processors and Amplifiers
In order to take full advantage of the CZR performance, make sure to adjust the crossover and equalizer (EQ) using
a processor/DSP built-in amplifier.
When selecting an amplifier, the amplifier should have a similar program (PGM) wattage rating to the speaker. For
example, since the PGM rating of the CZR12 is 800W, an amplifier of 640W to 1000W (0.8 to 1.25 times that of
800W) should be selected. However, when a speaker can be protected properly by a limiter, amplifiers with more
power can be used together.
Visit the CZR product page of the Yamaha Pro Audio global website for details on the recommended models of pro-
cessors and amplifiers, and EQ settings.
Basic Setting Example
This system is connected by two independent cables from a 2-channel amplifier to a CZR and a
subwoofer.
This system is connected by a single cable from the outputs of a 2-channel amplifier, using the
output jack on the CXS series.
The output jack of the CXS series (subwoofers) receives the signals via 2+/2– of the [INPUT/PARALELL] jack and routes
them to 1+/1– for output. Using the output jack of the CXS along with a 4-pole speakON cable, you can connect an amplifier
to the CXS with a single cable. For details, please refer to the relevant CXS series manual.
2-channel amplifier
1+/1–: SUBWOOFER
1+/1–: FULL RANGE
CXS series
(subwoofer)
CZR
From
amplifier
CXS series
(subwoofer)
2+/2–: FULL RANGE
CZR
2-channel amplifier
1+/1–: SUBWOOFER
To CZ R
OUTPUT
Routes the signals received via
2+/2– to 1+/1– for output.
1+/1–: FULL RANGE
From
amplifier
4-pole speakON
cable
CZR series Owner’s Manual 9
Rotatable Horn
When shipped from the factory, the directivity of CZR in a vertical orientation is the setting which makes the sound
expand in a horizontal direction, and inhibits or narrows the sound in a vertical direction. We recommend changing
the directivity by rotating the horn when you want to install CZR horizontally or when you want to use them as a floor
monitor and broaden the directivity.
1. Using a 2.5 mm hexagonal wrench, remove all fixing screws (CZR10: six total) on the grille, and remove the grille from the
speaker.
2. Using a No. 2 Phillips head screwdriver, remove all screws installed on the horn and pull the horn out from the speaker.
3. Rotate the horn 90 degrees, and re-install the horn to the speaker, reversing the steps above.
• Make sure not to push the screws too strongly with the Phillips head screwdriver. This may cause the nuts inside the cabinet to fall off.
• If the horn cannot smoothly be pulled out, hook the notches using a flat-bladed screwdriver, and pull out.
NOTE
Screws (eight total)
Notch
Vertical
Rotate 90°
Horizontal
10 CZR series Owner’s Manual
Switching Between Passive and Bi-amp Mode
The factory setting for CZR internal wiring is the Passive mode. However, you can change the setting to the Bi-amp
mode. When driving in the Bi-amp mode, you must use an external crossover processor and the output from a 2-
channel amplifier. By driving in the Bi-amp mode, protection can be set separately for the LF and HF, and precise set-
tings can be made for crossover frequency and time alignment between the LF and HF. This optimizes the perfor-
mance capacity of each unit and increases the limit capability.
1. Using a M5 Phillips head screwdriver, remove all fixing screws on the rear panel, and remove the rear panel.
2. Disconnect the input and output cable connectors from the [PASSIVE IN]/[PASSIVE OUT] connectors on the network base,
and connect them to [BI-AMP IN]/[BI-AMP OUT] connectors respectively.
3. Re-install the rear panel to the speaker, reversing the steps above. (The base shown below is of the CZR10.)
• When removing the screws, make sure not to push the screws strongly. This may cause the nuts inside the cabinet to fall off.
• If the rear panel cannot smoothly be removed, hook the notches using a flat-bladed screwdriver, and pull out.
After changing the mode, we recommend marking the appropriate blank on the rear panel list to indicate the current state.
NOTE
Screws (six total)
Notch
PASSIVE IN
PASSIVE OUT
BI-AMP
OUT
BI-AMP
IN
PASSIVE IN
PASSIVE OUT
BI-AMP
OUT
BI-AMP
IN
Passive Bi-amp
To speaker units
From [INPUT/PARALLEL] jack From [INPUT/PARALLEL] jack
To speaker units
NOTE
CZR series Owner’s Manual 11
Installation Examples
Suspended Installation Using Eye Bolts
Suspension angle
Make sure to use eye bolts within a range of 0 to 45 degrees from a right angle.
Suspended Installation Example
CAUTION
• Before doing any installation or construction work, consult with your Yamaha dealer.
• The installation should be checked thoroughly at regular intervals. Some fittings may deteriorate over extended periods of
time due to wear and/or corrosion.
• When choosing the installation location, suspension wire and mounting hardware, make sure all are strong enough to
support the weight of the speaker.
• Make sure to take precautionary measures using wires to prevent the speaker from falling down in the event of an installa-
tion failure.
• When installing the wire to the wall, install it higher than the wire’s attachment point on the speaker, with as little slack as
possible. If the wire is too long, and the speaker happens to fall, the wire may snap as a result of too much strain.
• Make sure to use eye bolts according to the standards and safety regulations in your area.
Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or
improper installation.
Attach commercially-available long eye bolts (30–50 mm in
length) to the screw holes for the eye bolts (t on page 6).
The screw diameter for CZR15 and CZR12 is M10, and the
screw diameters for CZR10 are M10 and M8. Keep in mind
that you will need two or more rigging points.
Securing the eye bolts
Insert the eye bolts through the washers when attaching
them.
• The screw holes for eye bolts go through the cabinet wall.
• When using eye bolts, remove the flat-head screws tightened at
the time of factory shipment. When not using eye bolts, tighten
the flat-head screws in order to prevent air leaks.
NOTE
Apply thread-
locking fluid
to the eye bolt
Bottom
0°
45°
Max. 45°
M10 eye bolt
Pullback point
Side
Max. 45°
Rear
12 CZR series Owner’s Manual
Installation Examples
Incorrect examples for suspended installation
Do not suspend the eye bolts as shown in the illustrations below.
Installation Using a Dedicated U-bracket
By using the separately sold Yamaha UB-DZR series U-bracket, you can expand the installation possibilities of the CZR. For
instructions on installing the U-bracket, refer to the corresponding manual for the UB-DZR series.
Examples
The UB-DZR series can be used together with separately sold optional brackets, such as the Yamaha BBS251 Baton Bracket.
More than
45°
More than
45°
More than 45°
from a right angle
Only one
suspension point
ProhibitedProhibited
ProhibitedProhibited
NOTE
CZR series Owner’s Manual 13
Troubleshooting
If any specific problem should persist, contact your Yamaha dealer.
Symptom Possible causes Possible solution
No sound. The cable is not connected properly.
Connect the speakON cable to the [INPUT/
PARALLEL] jack correctly. When using in the
Passive mode, make sure to connect the 1+/
1– contacts of the speakON cable to the
amplifier outputs.
Sound is interrupted sud-
denly.
The speaker units are damaged.
If no sound although the connection and sig-
nal level are appropriate, there is a possibility
of malfunction of the speaker units. Contact
your Yamaha dealer.
The amplifier shuts down.
When connecting the speakers in parallel,
the total impedance of the speakers is less
than the minimum load impedance of the
amplifier.
(For example, when more than three eight-
ohm speakers are connected in parallel to
an amplifier having a minimum load imped-
ance of four ohms.)
Lower the number of speakers connected in
parallel, or use an amplifier which can drive
with the total impedance of the speakers, in
order to not be less than the minimum load
impedance of the amplifier.
The protection system of the amplifier has
been enabled because the input volume is
excessive.
Wait until the amplifier cools down. Before
using it again, lower the input volume.
No high-frequency sound.
The HF protection system has been
enabled.
Refer to the “Protection Circuit” NOTICE on
page 3.
When using in the Bi-amp mode, the signals
are sent only to the 1+/1– contacts of the
[INPUT/PARALLEL] jack.
When using in Bi-amp mode, send the correct
signals to the 1+/1– and 2+/2– contacts of the
[INPUT/PARALLEL] jack.
(1+/1–: LF, 2+/2–: HF)
Sound is distorted. Input volume is excessive.
Lower the volume of the input device so that
the limit indicator of the amplifier lights only
occasionally.
100 CZR series Owner’s Manual
Specifications
General Specifications
*1: With recommended DSP processing.
*2: Full-space (4π)
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website
then download the manual file.
Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die neueste Version der
Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter.
Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date de publication du manuel. Pour obtenir la
version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du manuel concer
né.
El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último manual, acceda al sitio
web de Yamaha y descargue el archivo del manual.
O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual mais recente, acesse o
site da Yamaha e faça o download do arquivo do manual.
Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere la versione più
recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente.
В содержании данного руководства приведены последние на момент публикации технические характеристики. Для получения
последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с руководством.
CZR15 CZR12 CZR10
System Type 2-way speaker, Bass-reflex
Frequency Range
(-10 dB)
Passive 43 Hz – 20 kHz 43 Hz – 20 kHz 43 Hz – 20 kHz
Normal
*1
34 Hz – 20 kHz 42 Hz – 20 kHz 46 Hz – 20 kHz
FOH
*1
33 Hz – 20 kHz 38 Hz – 20 kHz 43 Hz – 20 kHz
Coverage Angle H90° × V50° Rotatable,
Constant directivity horn
H90° × V60° Rotatable,
Constant directivity horn
H90° × V60° Rotatable,
Constant directivity horn
Crossover Frequency (Passive) 2.0 kHz 2.0 kHz 2.5 kHz
Nominal Impedance Passive 8 Ω 8 Ω 8 Ω
Bi-amp LF: 8 Ω, HF: 16 Ω LF: 8 Ω, HF: 16 Ω LF: 8 Ω, HF: 16 Ω
Power Rating
(EIA 426-A)
Passive NOISE 400 W 400 W 350 W
PGM 800 W 800 W 700 W
MAX 1600 W 1600 W 1400 W
Power Rating
(LF: EIA 426-A)
(HF: AES)
Bi-amp NOISE LF: 400 W, HF: 50 W LF: 400 W, HF: 50 W LF: 350 W, HF: 50 W
PGM LF: 800 W, HF: 100 W LF: 800 W, HF: 100 W LF: 700 W, HF: 100 W
MAX LF: 1600 W, HF: 200 W LF: 1600 W, HF: 200 W LF: 1400 W, HF: 200 W
Sensitivity
(1 W, 1 m)
*2
Passive 97 dB SPL 97 dB SPL 95 dB SPL
Bi-amp LF: 99 dB SPL,
HF: 108 dB SPL
LF: 97 dB SPL,
HF: 108 dB SPL
LF: 95 dB SPL,
HF: 108 dB SPL
Maximum SPL
(Calculated, 1 m)
*2
Passive 129 dB SPL 129 dB SPL 127 dB SPL
Bi-amp LF: 131 dB SPL,
HF: 131 dB SPL
LF: 129 dB SPL,
HF: 131 dB SPL
LF: 127 dB SPL,
HF: 131 dB SPL
Transducer LF 15" Cone, 3" Voice coil,
Neodymium magnet
12" Cone, 3" Voice coil,
Neodymium magnet
10" Cone, 3" Voice coil,
Neodymium magnet
HF 2" Voice coil, 1" Throat compression driver, Titanium diaphragm, Neodymium magnet
Enclosure Material, Finish, Color Plywood, Durable polyurea coating, Black
Floor Monitor Angle 50° Symmetrical 50° Symmetrical 50°
Dimensions
(W × H × D, with rubber feet)
450 × 761 × 460 mm 410 × 646 × 394 mm 315 × 537 × 345 mm
Net Weight 21.3 kg 18.0 kg 14.0 kg
Handles
Aluminium die-cast, Side × 2
Aluminium die-cast,
Top × 1, Side × 1
Pole Socket Ø35 mm × 2 (0° or -7°)
Rigging Points
M10 × 12
M10 × 8
M8 × 2
Connectors speakON NL4MP × 2 (Parallel)
Optional Bracket UB-DZR15H, UB-DZR15V UB-DZR12H, UB-DZR12V UB-DZR10H, UB-DZR10V
Optional Cover SPCVR-DZR15 SPCVR-DZR12 SPCVR-DZR10
Specifications (English only)
CZR series Owner’s Manual 101
Specifications
Dimensions
41672
2xM10
460
41672
329
254
257240
2xM10
2xM8
367
240
41
254
329
3xM10
2xM8
450
761
367
240
41
254
329
3xM10
2xM8
504
50°
CZR15
Unit: mm
2xM8
2xM8
3xM10
41
239
277
240
327
2xM8
3xM10
646
410
239
394
277
199.5240
41557
2xM10
41557
2xM10
240
327
41
239
277
444
50°
CZR12
Unit: mm
102 CZR series Owner’s Manual
Specifications
Block Diagram (CZR15, CZR12, CZR10)
233
240
166
236
2xM8
2xM10
315
537
233
166
236
240
2xM10
2xM8
392
50°
236
176
41
145240
451
345
2xM8
2xM10
28474
2xM8
CZR10
Unit: mm
NL4
Passive mode (Factory setting)
NL4
1±
2±
1±
2±
1±
INPUT/
PARALLEL
LF
HF
NL4
Bi-amp mode (Selectable)
NL4
1±
2±
1±
2±
1±
+
–
+
–
LF±
HF±
INPUT/
PARALLEL
2±
LF
HF
+
–
+
–
LF±
HF±
PASSIVE
X-OVER
NETWORK
CZR series Owner’s Manual 103
Yamaha Pro Audio global website
https://www.yamaha.com/proaudio/
Yamaha Downloads
https://download.yamaha.com/
ZW46810
Manual Development Group
© 2018 Yamaha Corporation
Published 04/2018 POEI-A0
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
Yamaha CZR10 Omistajan opas
- Kategoria
- Audio amplifiers
- Tyyppi
- Omistajan opas
muilla kielillä
- polski: Yamaha CZR10 Instrukcja obsługi
- Türkçe: Yamaha CZR10 El kitabı
- English: Yamaha CZR10 Owner's manual
- čeština: Yamaha CZR10 Návod k obsluze
- svenska: Yamaha CZR10 Bruksanvisning
- русский: Yamaha CZR10 Инструкция по применению
- italiano: Yamaha CZR10 Manuale del proprietario
- Deutsch: Yamaha CZR10 Bedienungsanleitung
- português: Yamaha CZR10 Manual do proprietário
- dansk: Yamaha CZR10 Brugervejledning
- français: Yamaha CZR10 Le manuel du propriétaire
- español: Yamaha CZR10 El manual del propietario
- Nederlands: Yamaha CZR10 de handleiding
- română: Yamaha CZR10 Manualul proprietarului