Yamaha MMP1 Getting Started

Merkki: Yamaha

Malli: MMP1

Luokka: Supplementary music equipment

Tyyppi: Getting Started

EnglishDeutschFrançaisEspañolPortuguêsItaliano

SIGNAL PROCESSOR

Getting Started

Einführung

Prise en Main

Cómo Empezar

Introdução

Guida Introduttiva

Приступая к работе

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of interfer-

ence, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the fol-

lowing measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Signal processor

Model Name : MMP1

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로

가정에서 사용하는 것을 목적으로 하며 , 모든

지역에서 사용할 수 있습니다 .

(class b korea)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så

länge som den ar ansluten till vägguttaget, även om

själva apparaten har stängts av.

ADVARSEL: Netspændingen til dette apparat er IKKE

afbrudt, sålænge netledningen sidder i en stikkontakt,

som er tændt — også selvom der er slukket på

apparatets afbryder.

VAROITUS: Laitteen toisiopiiriin kytketty käyttökytkin

ei irroita koko laitetta verkosta.

(standby)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig

håndtering. Udskiftning må kun ske med batteri af

samme fabrikat og type. Levér det brugte batteri tilbage

til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma

batterityp eller en ekvivalent typ som rekommenderas av

apparattillverkaren. Kassera använt batteri enligt

fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan

suosittelemaan tyyppiin. Hävitä käytetty paristo

valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur of gelieve dan

contact op te nemen met de vertegenwoordiging van Yamaha in uw land.

• For the removal of the battery at the moment of the disposal at the end of

life please consult your retailer or Yamaha representative office in your

country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical waste.

(lithium disposal)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(Perchlorate)

Explanation of Graphical Symbols

Explication des symboles

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension

dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been

dropped.

(UL60065_03)

PRÉCAUTIONS CONCER-

NANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur comme

un radiateur, une bouche de chaleur, un poêle ou tout autre appareil

(y compris un amplificateur) produisant de la chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de la

fiche de terre. Une fiche polarisée dispose de deux broches dont une

est plus large que l’autre. Une fiche de terre dispose de deux broches

et d’une troisième pour le raccordement à la terre. Cette broche plus

large ou cette troisième broche est destinée à assurer la sécurité de

l’utilisateur. Si la fiche équipant l’appareil n’est pas compatible avec

les prises de courant disponibles, faire remplacer les prises par un

électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas

piétinés ni coincés, en faisant tout spécialement attention aux fiches,

prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le

trépied, le support ou la table recommandés par

le fabricant ou vendus avec cet appareil. Si

l’appareil est posé sur un chariot, déplacer le

chariot avec précaution pour éviter tout risque

de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou

lorsqu’il doit rester hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la fiche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou des

objets sont tombés à l’intérieur de l’appareil, si l’appareil a été exposé

à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas

normalement ou est tombé.

(UL60065_03)

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION :

POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER

LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT

L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,

FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.

ATTENTION

RISQUE DE CHOC

ELECTRIQUE-NE PAS OUVRIR

The above warning is located on the top of the unit. L’avertissement ci-dessus est situé sur le dessus de l’unité.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

4 MMP1 Getting Started

Contents

PRECAUTIONS.....................................................................................5

NOTICE..............................................................................................................6

Information.......................................................................................................... 7

1. Welcome ...........................................................................................8

1-1. Intended user ............................................................................................8

1-2. Intended usage..........................................................................................8

1-3. Included accessories................................................................................. 8

1-4. Documentation ..........................................................................................8

1-5. Nomenclature used in this book ................................................................8

1-6. Applications ............................................................................................... 8

1-7. Firmware updates......................................................................................8

2. Names and Functions......................................................................9

2-1. Front panel ............................................................................................... 9

2-2. Rear panel .............................................................................................. 10

3. Location and Connections............................................................12

3-1. Connection example ...............................................................................12

3-2. Before connecting ...................................................................................12

3-3. Precautions for rack mounting.................................................................13

3-4. Power supply........................................................................................... 13

3-5. About Dante ............................................................................................13

3-6. Notes regarding the use of network switches.......................................... 13

3-7. Dante network settings and audio routing...............................................13

4. Installing Applications...................................................................14

4-1. MMP1 Editor............................................................................................14

4-2. MMP1 Controller .....................................................................................14

5. Troubleshooting.............................................................................15

5-5. Restoring factory settings........................................................................15

6. Specifications............................................... at the end of the book

6-9. General specifications ............................................. at the end of the book

6-10. Pin assignment......................................................... at the end of the book

6-11. Dimensions .............................................................. at the end of the book

7. Software Licenses and Copyrights............ at the end of the book

MMP1 Getting Started 5

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, fire or

other hazards. These precautions include, but are not

limited to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Only use the voltage specified as correct for the device. The

required voltage is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet, and also

disconnect the connected power supply from the [BACKUP

DC INPUT] connector. Even when the power switch is

turned off, as long as the power cord is not unplugged from

the wall AC outlet, the device will not be disconnected from

the power source.

• Remove the electric plug from the outlet when the device is

not to be used for extended periods of time, or during

electrical storms.

• Be sure to connect to an appropriate outlet with a protective

grounding connection.

Do not open

• This device contains no user-serviceable parts. Do not open

the device or attempt to disassemble the internal parts or

modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings. If any liquid such as water seeps

into the device, turn off the power immediately and unplug

the power cord from the AC outlet, and also disconnect the

connected power supply from the [BACKUP DC INPUT]

connector. Then have the device inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• Before connecting the device to other devices, turn off the

power for all devices. Failing to do so may result in hearing

loss, electric shock, or device damage.

• When turning on the power in your audio system, always

turn on the power amplifier LAST, to avoid hearing loss and

speaker damage. When turning the power off, the power

amplifier should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames near the

device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet and also disconnect the connected power supply

from the [BACKUP DC INPUT] connector.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualified

Yamaha service personnel.

• If this device or the power supply should be dropped or

damaged, immediately turn off the power switch,

disconnect the electric plug from the outlet and also

disconnect the connected power supply from the [BACKUP

DC INPUT] connector, and then have the device inspected

by qualified Yamaha service personnel.

PA_en_8 1/2

6 MMP1 Getting Started

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the device or other property. These

precautions include, but are not limited to, the

following:

Power supply/power cord

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

• To disconnect the device from the mains, unplug both

power cords.

Location

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

• Do not block the vents. This device has ventilation holes at

the sides to prevent the internal temperature from becoming

too high. In particular, do not place the device on its side or

upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or

even fire.

• Do not place the device in a location where it may come into

contact with corrosive gases or salt air. Doing so may result

in malfunction.

• Before moving the device, remove all connected cables.

• If the device is mounted in an EIA standard rack, carefully

read the section “Precautions for rack mounting” on

page 13. Inadequate ventilation can result in overheating,

possibly causing damage to the device(s), malfunction, or

even fire.

Maintenance

• Remove the power plug from the AC outlet and also

disconnect the connected power supply from the [BACKUP

DC INPUT] connector when cleaning the device.

Handling caution

• Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device (vents).

If this happens, immediately turn off the power and then

unplug the power cord from the AC outlet, and have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy

objects on it. Avoid applying excessive force to the buttons,

switches or connectors to prevent injuries.

• Avoid pulling the connected cables to prevent injuries or

damage to the device.

Backup battery

• Do not replace the backup battery by yourself. Doing so

may cause an explosion and/or damage to the device(s).

When the backup battery needs to be replaced, the error

icon will appear on the menu bar of the MMP1 Editor while

the MMP1 is connected to the MMP1 Editor. In this case,

contact your Yamaha dealer and have qualified Yamaha

service personnel replace the backup battery.

NOTICE

To avoid the possibility of malfunction/ damage to the product,

damage to data, or damage to other property, follow the

notices below.

Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, AV

equipment, mobile phone, or other electric devices.

Otherwise, the device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or

extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic

changes in ambient temperature—when the device is

moved from one location to another, or air conditioning is

turned on or off, for example. Using the device while

condensation is present can cause damage. If there is

reason to believe that condensation might have occurred,

leave the device for several hours without turning on the

power until the condensation has completely dried out.

• The rubber feet included in this package can be attached to

the device to prevent slippage when it is to be used on a

slippery surface.

• Always turn the power off when the device is not in use.

• Even when the both ( ) [MAIN] switch and () [BACKUP]

switch are in standby status (power indicators are off),

electricity is still flowing to the instrument at the minimum

level. When you are not using the instrument for a long time,

make sure you unplug the power cord from the wall AC

outlet, and also disconnect the connected power supply

from the [BACKUP DC INPUT] jack.

Yamaha cannot be held responsible for damage caused

by improper use or modifications to the device, or data

that is lost or destroyed.

PA_en_8 2/2

MMP1 Getting Started 7

Saving data

This device has a built-in backup battery that maintains data

in internal memory even when the device’s power is switched

off. The backup battery will eventually become depleted,

however, and when that happens the contents of the internal

memory will be lost.* To prevent loss of data be sure to

replace the backup battery before it becomes fully depleted.

When the remaining capacity of the backup battery becomes

so low that it needs to be replaced, the error icon will appear

on the menu bar of MMP1 Editor while the MMP1 is connected

to the MMP1 Editor. If either of these messages appears do

not turn off the power and immediately transfer any data you

want to save to a computer or other external storage device,

then have qualified Yamaha service personnel replace the

backup battery. The average life of the internal backup battery

is approximately five years, depending on operating

conditions.

Information

About functions/data bundled with the

product

• This product uses Dante Brooklyn II.

Refer to the Audinate website (English) for details on the

open source licenses for the particular software.

https://www.audinate.com/software-licensing

About this manual

• The illustrations and screens as shown in this manual are for

instructional purposes only.

• Yamaha Corporation make no representations or warranties

with regard to the use of the software and documentation

and cannot be held responsible for the results of the use of

this manual and the software.

• Windows is a registered trademark of Microsoft

Corporation in the United States and other countries.

• Mac and iPad are trademarks of Apple Inc., registered in

the U.S. and other countries.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

• Software may be revised and updated without prior notice.

European models

Purchaser/User Information specified in EN55103-2:2009.

Conforms to Environments: E1, E2, E3 and E4

(weee_eu_en_02)

(top_en_01)

Information for users on collection and

disposal of old equipment:

This symbol on the products, packaging,

and/or accompanying documents means

that used electrical and electronic products

should not be mixed with general household

waste.

For proper treatment, recovery and recycling

of old products, please take them to

applicable collection points, in accordance

with your national legislation.

By disposing of these products correctly, you will help to

save valuable resources and prevent any potential

negative effects on human health and the environment

which could otherwise arise from inappropriate waste

handling.

For more information about collection and recycling of old

products, please contact your local municipality, your

waste disposal service or the point of sale where you

purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment,

please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside

the European Union:

This symbol is only valid in the European Union. If you

wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of

disposal.

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the top of

the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record

of your purchase to aid identification in the event of theft.

Model No.

Serial No.

1. Welcome

8 MMP1 Getting Started

1. Welcome

Thank you for choosing the Yamaha signal processor

MMP1. In order to take full advantage of the MMP1

functionality and enjoy years of trouble-free use, please

read this manual. After you have read the manual, keep it

in a safe place for your future reference.

1-1. Intended user

This product was designed for users who have basic

knowledge and skills related to post-production, audio

recording, or broadcasting.

1-2. Intended usage

• This product was designed to be used to improve the

monitoring and communication environment during

studio recording with a DAW.

• This product was designed to be used to mix multiple

audio sources, and routing audio signals in

broadcasters.

1-3. Included accessories

• Getting Started (this book)

• Power cord

• Rubber stoppers (×4)

1-4. Documentation

The MMP1 has the following two separate manuals.

Getting Started (this book)

This manual primarily explains operations in setting up this

product for use, such as installation and connection.

Operation Manual

(PDF; available as download)

This manual explains operations of the product when

used with a dedicated application. You can download the

Operation Manual from the Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

NOTE

The Operation Manual is an electronic manual in PDF format. You

can download the latest Adobe Acrobat Reader DC required to

read the PDF file from the website listed below:

https://www.adobe.com/

1-5. Nomenclature used in this

book

In order to distinguish between the controls on the MMP1

unit and the controls on the screen, control names are

written in the following manner:

• Actual buttons on the unit are called keys, and virtual

buttons on the screen are called buttons.

• Keys, switches, indicators, jacks, etc. located on the

unit are enclosed in [square brackets]. For certain

controls, the name of the section appears before the

brackets (e.g., the SCENE [1] key).

• Menus, buttons, tabs, windows, etc. displayed on the

screen are enclosed in “quotation marks.” (e.g., the

“MUTE” button)

1-6. Applications

To operate MMP1, use the following applications:

• MMP1 Editor (Windows, Mac)

This application allows you to control all functions of the

MMP1.

• MMP1 Controller (iPad)

This application is designed for easy operation of the

MMP1, with a limited set of controllable functions.

Before using the MMP1 Controller, you will need to make

initial settings to your MMP1 using the MMP1 Editor.

For details of these applications, refer to the MMP1

Operation Manual, downloadable from the Yamaha Pro

Audio website:

http://www.yamahaproaudio.com/

1-7. Firmware updates

You can update the unit firmware to improve operation,

add functions, and correct possible malfunctions.

Details on updating the firmware are available on the

Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

For information on updating the firmware, refer to the

firmware update guide available on the website.

NOTE

To maintain compatibility between Dante-compatible devices,

updating of multiple Dante-compatible devices may be needed.

For details, refer to the firmware compatibility information

available on the Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

2. Names and Functions

MMP1 Getting Started 9

2. Names and Functions

2-1. Front panel

SCENE [1] – [5], [RECALL] keys

Used to recall previously stored Scenes in the unit. When

pressing one of the [1] – [5] keys, the key flashes for

about 10 seconds. (If a Scene corresponding to the key is

not stored, the key doesn’t flash.) When pressing the

[RECALL] key while one of the [1] – [5] keys are flashing,

the Scene is recalled, and the key is lit continuously. Use

the MMP1 Editor to store Scenes.

NOTE

You can set the [1] key as the all mute key. For details, refer to the

MMP1 Operation Manual.

SAMPLE RATE indicators

Indicate the current sample rate being used by the unit.

The indicator which synchronizes with the word clock

source lights up. If the unit cannot synchronize with the

word clock source, one of these indicators flashes slowly.

CLOCK indicators

Indicate a word clock source. When the word clock

source is not connected to the unit or the word clock

source has any problems, one of these indicators flashes

slowly.

SYNC indicators

Indicate the sync status between the Dante network and

the unit.

SYSTEM indicators

Indicate the operating status of the unit.

[BACKUP] power switch and indicator

Turns the DC power of the unit to on ( ) or sets it to

standby (). When the DC power unit is turned on, the

indicator lights up.

NOTICE

Even when the power switch is in the standby position (), a

small amount of current is flowing through the unit. When

you are not using the unit for a long time, make sure to

disconnect the power supply from the [BACKUP DC INPUT]

connector.

NOTE

Setting the unit to on and standby in rapid succession can cause

it to malfunction. After setting the unit to standby, wait for at least

6 seconds before turning it on again.

Green (lit continuously) The unit is working as a clock slave

on the Dante network.

Green (flashing slowly) The unit is working as the clock

master on the Dante network.

Green (off)

Orange (lit continuously)

Synchronization with the Dante

network is in progress.

Orange (flashing slowly) In communication with the secondary

line of a redundant network.

Orange (flashing twice) An error has occurred on the

secondary line of a redundant

network.

Green (lit continuously)

Red (off)

The unit is working properly.

Green (flashing slowly) The firmware is being updated.

Red (lit continuously) An error has occurred in the memory

of the unit. If the issue is still not

solved even when following the

“Restoring factory settings”

instructions on page 15, please

contact your Yamaha dealer.

Red (flashing slowly) An error has occurred in the Dante

module of the unit.

Red (flashing rapidly) The backup battery voltage is

reduced. Please contact your

Yamaha dealer and have qualified

Yamaha service personnel replace

the backup battery.

2. Names and Functions

10 MMP1 Getting Started

[MAIN] power switch and indicator

Turns the AC power of the unit to on ( ) or sets it to

standby (). When the AC power unit is turned on, the

indicator lights up.

When both the [MAIN] power switch and [BACKUP]

power switch are on ( ), only AC power is supplied to the

unit.

NOTICE

Even when the power switch is in the standby position (), a

small amount of current is flowing through the unit. When

you are not using the unit for a long time, make sure to

unplug the power cord from the AC outlet.

NOTE

Setting the unit to on and standby in rapid succession can cause

it to malfunction. After setting the unit to standby, wait for at least

6 seconds before turning it on again.

Vent

This unit is equipped with cooling fans. These vents let

warm air out from the unit. Please make sure that you do

not block the vents with any object.

2-2. Rear panel

AC power input socket

For connecting the supplied AC power cord. First,

connect the AC power cord to this unit, and then insert the

power cord plug into an appropriate AC outlet.

Make sure to insert the cord plugs all the way until they

lock in place securely. The supplied AC power cord

features a V-lock mechanism with a latch, which prevents

the power cord from being accidentally disconnected.

CAUTION

Be sure to set to standby

the power of the unit

before connecting or

disconnecting the power cord. To

disconnect the power cord, hold

down the latch on the plug while

removing it.

[BACKUP DC INPUT] connector

For connecting the external DC power unit (+12 V, 45 W)

for backup of AC power supply. The connector type is

XLR-4-32. Refer to “Specifications” for pin assignments.

CAUTION

Before connecting or disconnecting the external

power supply, you must set to standby the power

of this unit and the power of the external power

supply. Malfunctions or electrical shock may occur if you fail

to observe this caution.

NOTICE

When connecting an external DC power supply, please make

sure that it has a sufficient power supply rating. If it has an

insufficient power supply rating, the inrush current when the

unit is turned on may lead to unstable operation or cause a

malfunction. In order to prevent malfunction due to the inrush

current when the unit is turned on, please turn on the unit via

the [MAIN] power switch, rather than the [BACKUP]

power switch.

NOTE

•

AC power is supplied to the unit when both the [MAIN] and

[BACKUP] power switches are turned on.

• When both power supplies are turned on, it automatically

switches to the external DC power supply if a malfunction

causes the AC power supply to be interrupted.

[UNIT ID] rotary switch

Determines the ID that identifies this device on the Dante

network. If there are multiple Dante-compatible devices

from Yamaha that require an ID setting connected to the

same network, set a different ID for each device.

NOTE

The ID setting while the power-on will be applied the next time

you turn the power on.

DIP switches

Used to change settings on the unit. Refer to the sections

“Before connecting” on page 12 and “Restoring factory

settings” on page 15.

NOTE

The setting while the power is on will be applied the next time you

turn the power on.

Vents

Even when the [BACKUP] power switch is in the

standby position, standby current is discharged. For

this reason, Yamaha does not guarantee the use of

batteries.

2. Names and Functions

MMP1 Getting Started 11

GPI [INPUT]/[OUTPUT] connectors

For connecting GPI-equipped devices. The connector

type is D-Sub 25-pin female. Use the MMP1 Editor for

detailed GPI settings of the unit. Refer to “Specifications”

for current and voltage of each pin, and for pin

assignments.

Dante [LINK/ACT]/[1G] indicators

Display the communication status of the Dante [PRIMARY]

and the [SECONDARY] connectors.

Dante [PRIMARY]/[SECONDARY] connectors

For connecting to the Dante network. The connector type

is etherCON (RJ-45). A connector can transfer up to 64

channels (in/out) of audio.

NOTE

•

Use an STP (Shielded Twisted Pair) cable of CAT5e standard

or better to prevent electromagnetic interference. Make sure

that the metal parts of the plugs are electrically connected to

the STP cable shield by conductive tape or comparable

means.

• For connecting only Dante-compatible devices or GbE-

compatible devices (including a computer).

WORD CLOCK [IN]/[OUT] connectors

For connecting devices to receive or transmit word clock

signals. The connector type is BNC. The WORD CLOCK

[IN] connector is internally terminated by a 75 ohm

resistor.

ANALOG [INPUT 1-8]/[OUTPUT 1-8] connectors

For connecting devices to transmit or receive analog

audio signals. The connector type is 25-pin D-Sub

(balanced). A connector can transfer up to eight channels

(in/out) of audio.

[AES/EBU 1-8]/[AES/EBU 9-16] connectors

For connecting devices to transmit or receive AES/EBU

format digital audio signals. The connector type is 25-pin

D-Sub. A connector can transfer up to eight channels (in/

out) of audio.

NOTE

Use a shielded cable to prevent electromagnetic interference.

Make sure that the metal parts of the plugs are electrically

connected to the cable shield by conductive tape or comparable

means.

LINK/ACT These indicators flash rapidly if the Ethernet

cables are connected properly.

1G These indicators are lit when the Dante

network is functioning as Giga-bit Ethernet.

3. Location and Connections

12 MMP1 Getting Started

3. Location and

Connections

3-1. Connection example

3-2. Before connecting

Make various settings of the unit in advance.

3-2-1. UNIT ID

3-2-2. How to connect to the Dante network

3-2-3. IP address

3-2-1. UNIT ID

Determines the ID for identifying each device on the

Dante network. For this setting, use the rotary switch on

the rear panel of the unit. The UNIT ID must be a unique

number in the network.

3-2-2. How to connect to the Dante

network

The unit can be connected to the Dante network in one of

two ways: Star (Redundant) and Daisy Chain. For this

setting, use the DIP switch 1 on the rear panel of the unit.

3-2-3. IP address

Determines the IP address for identifying this unit from a

computer. For this setting, use the DIP switch 7 and 8 on

the rear panel of the unit.

Any settings you change while the power is on will be

retained and applied the next time you turn the power

on.

MMP1

Mic mute switch

Network switch

Preamp

Computer

Audio signals

Control signals

DAW

Talkback

DAISY CHAIN

DIP switch 1

up (default).

REDUNDANT

DIP switch 1

down.

Auto IP

DIP switch 7 and 8

up.

An IP address is automatically set in the

range of from 169.254.0.1 to

169.254.254.254 (default).

DHCP

DIP switch 7

down and 8 up.

An IP address is assigned by the DHCP

server.

Static IP (Auto)

DIP switch 7

up and 8 down.

The IP address is set to 192.168.0.xx (xx is

the UNIT ID).

Static IP (Manual)

DIP switch 7 and 8

down.

Set the IP address using the MMP1 Editor.

3. Location and Connections

MMP1 Getting Started 13

3-3. Precautions for rack

mounting

This unit is rated for operation at ambient temperatures

ranging from 0 to 40 degrees Celsius. If you mount this

unit along with other MMP1 unit(s) or other device(s) in an

EIA standard equipment rack, temperatures inside the

rack may rise, possibly resulting in impaired performance.

When rack mounting the unit, always observe the

following requirements to avoid heat buildup:

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave 1U space or more between the MMP1 and

other equipment. Also, either leave the open spaces

uncovered or install appropriate ventilating panels to

minimize the possibility of heat buildup.

• To ensure sufficient airflow, leave the rear of the rack

open and position it at least 10 centimeters from walls or

other surfaces.

If the rear of the rack cannot be left open, install a

commercially-available fan or similar ventilating option to

ensure sufficient airflow. If you have installed a fan kit,

there may be cases in which closing the rear of the rack

will produce a greater cooling effect.

Refer to the rack and/or fan unit manual for details.

3-4. Power supply

3-4-1. Connecting the AC power cord

1. Make sure that the [MAIN] power switch

and the [BACKUP] power switch are in the

standby position ( ).

2. Connect the supplied power cord to the AC

power input socket of the unit.

3. Connect the other end of power cord to an AC

outlet.

NOTE

•

To disconnect the power cord,

remove the cable in the order of

steps 1  3  2 in the procedure

described above.

• To disconnect the power cord,

remove it while holding down the

latch on the plug.

WARNING

Use only the supplied AC power cord. Using other

cables may lead to overheating or electric shock.

CAUTION

Be sure to set to standby the power to the unit

before connecting or disconnecting the power

cord.

NOTICE

Even when the power switch is in the standby position (), a

small amount of current is flowing through the unit. If you

plan not to use the unit for a long period of time, be sure to

remove the power cord from the AC outlet.

3-4-2. Turning the power on and set to

standby

When you turn on the power to the unit, be sure to turn on

the power to the power amplifiers and/or powered

speakers last to avoid speaker damage. Before you set to

standby the power of the unit, first turn off the power to the

power amplifiers and/or powered speakers.

3-5. About Dante

Dante is a network audio protocol developed by Audinate.

It is designed to deliver multi-channel audio signals at

various sampling and bit rates, as well as device control

signals over a Giga-bit Ethernet (GbE) network.

Visit the Audinate website for more details on Dante:

https://www.audinate.com/

More information on Dante is also posted on the Yamaha

Pro Audio website:

http://www.yamahaproaudio.com/

3-6. Notes regarding the use

of network switches

Do not use the EEE functionality (*) of network switches on

a Dante network.

Although mutual power consumption settings between

switches that support the EEE functionality are adjusted

automatically, there are some switches for which such

mutual settings are not adjusted correctly.

This may cause EEE to be enabled in Dante networks

when it is not appropriate, resulting in poor

synchronization performance and occasional dropouts.

Therefore we strongly recommend the following.

• If you use managed switches, please disable the EEE

functionality. Do not use switches that prevent EEE

functionality from being disabled.

• When using unmanaged switches, do not use switches

that support EEE functionality. EEE functionality cannot

be disabled for such switches.

* EEE (Energy Efficient Ethernet) is a technology that reduces

switch power consumption during periods of low network traffic.

It is also referred to as Green Ethernet and IEEE802.3az.

3-7. Dante network settings

and audio routing

With the Dante network, you can route the audio input and

output of multiple Dante devices in any way you like. This

requires you to set which channel signals are sent to

which inputs.

Use Dante Controller to configure the audio routing of the

Dante network.

You can download Dante Controller from the following

website:

https://www.audinate.com/products/software/dante-

controller?lang=en

Refer to the Dante Controller owner’s manual (available

from the same website) for details about Dante Controller.

4. Installing Applications

14 MMP1 Getting Started

4. Installing Applications

4-1. MMP1 Editor

The MMP1 Editor is an application for operating the

MMP1. It is compatible with Windows and Mac.

1. Login with administrative privileges to your

computer to install the MMP1 Editor.

2. Download the MMP1 Editor (installer) from the

Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

3. Decompress the downloaded file.

4. Double-click the installer in the

decompressed folder to start installation.

The installer name is “setup.exe” (for Windows),

“Yamaha MMP1 Editor Vx.x.x.pkg” (for Mac). The

characters “x.x.x” indicate the version of the MMP1.

5. Follow the onscreen instructions.

NOTE

•

In Windows, when the “User Account Control” dialog box

appears, click [Continue] or [Yes].

• To uninstall the MMP1 Editor

Windows: In Control Panel, click [Programs and functions] or

[Uninstall a program], then select the MMP1 Editor, and click

[Uninstall or change].

Mac: double-click the “Uninstall Yamaha MMP1 Editor.app,”

and then follow the instructions on screen.

4-2. MMP1 Controller

MMP1 Controller is an application for iPad to operate

MMP1. This application is designed to operate MMP1

intuitively by limiting controllable functions compared to

MMP1 Editor.

1. Search the “MMP1 Controller” at the App

Store.

2. Tap the “MMP1 Controller” to display details.

3. Tap “Free” button.

4. Tap “Install” button.

5. Follow the instructions on screen.

5. Troubleshooting

MMP1 Getting Started 15

5. Troubleshooting

In addition to referring to this list of common problems/

solutions, visit the Yamaha Pro Audio website for an FAQ

list (Frequently Asked Questions).

http://www.yamahaproaudio.com/

5-1. MMP1 could not be found

from a computer or iPad

• Make sure that a unique UNIT ID has been set, when

working within the same Dante network.

• Make sure that the network switch is working properly.

The problem may be solved by turning the network

switch off and on again.

• Make sure that the cable is not damaged. The problem

may be solved by replacing the cable.

• Make sure that the IP address of the computer and the

IP address of the unit are set properly.

5-2.No sound

When the device is connected to the Dante network, make

sure that patching within the Dante network is set up

correctly with the Dante Controller.

For details, refer to the Dante Controller User Guide

available on the website.

https://www.audinate.com/products/software/dante-

controller?lang=en

5-3.How to update the firmware

Details on updating the firmware are available on the

following Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

5-4.An internal error message

(such as “firmware

mismatch”) appears on the

device connected to the

MMP1

Make sure that each device has a compatible version.

For details, refer to the firmware compatibility information

available on the website.

http://www.yamahaproaudio.com/

5-5. Restoring factory settings

Follow the steps below to initialize the internal memory of

the unit to the factory programmed settings.

1. Set the unit to standby.

2. Turn on DIP switch 2 (DOWN), and turn the

unit on again.

All front panel indicators (except the power indicator)

flash, indicating all parameters have been restored to

the factory settings.

3. Set the unit to standby.

4. Turn off DIP switch 2 (UP), and turn the unit on

again.

6. Specifications

6-1. ELECTRICAL CHARACTERISTICS

6-2. ANALOG INPUT CHARACTERISTICS

6-3. ANALOG OUTPUT CHARACTERISTICS

6-4. DIGITAL INPUT CHARACTERISTICS

6-5. DIGITAL OUTPUT CHARACTERISTICS

6-6. DIGITAL INPUT & OUTPUT CHARACTERISTICS

Sampling Frequency

Internal 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz

External 44.1kHz/48kHz/88.2kHz/96kHz/176.4kHz/192kHz, ±200ppm

Analog Input/Output

Frequency Response -1/0.5 dB, 20Hz – 20kHz

THD+N 0.0036%, +4dB@20Hz – 20kHz, GAIN: 0dB, Fs=192kHz

Dynamic Range 110dB, A-weighted

Crosstalk@1kHz -100dB

Input

Terminals

Actual Load

Impedance

For Use with

Nominal

Input level

Connector

Balanced /

Unbalanced

Nominal

Max. before clip

ANALOG INPUT

1 – 8

20kΩ 150Ω Lines

+4dB

(1.23 V)

+24dBu

(12.28V)

D-SUB

Connector 25P

(Female)

Balanced

10kΩ 600Ω Lines

-10dBV

(0.32 V)

+10dBV

(3.16V)

Unbalanced

Output

Terminals

Actual Source

Impedance

For Use with

Nominal

Output level

Connector

Balanced /

Unbalanced

Nominal

Max. before clip

ANALOG

OUTPUT 1 – 8

75Ω (BAL) 10kΩ Lines

+4dBu

(1.23 V)

+24dBu

(12.28V)

D-SUB

Connector 25P

(Female)

Balanced

-2dBu

(0.62V)

+18dBu

(6.16 V)

Terminal Format Data length Level Connector

Balanced /

Unbalanced

AES/EBU 1 – 16 AES/EBU 24bit RS422

D-SUB Connector

25P (Female)

Balanced

Terminal Format Data length Level Connector

Balanced /

Unbalanced

AES/EBU 1 – 16 AES/EBU 24bit RS422

D-SUB Connector

25P (Female)

Balanced

Terminal Format Data length Level Audio Connector

Primary/Secondary Dante 24bit 1000Base-T

64ch Input

64ch Output

etherCON x 2

6-7. CONTROL I/O CHARACTERISTICS

• GPI inputs ch1-12: optically isolated. Load current = 3 mA (typical). See figure 1.

• GPI inputs ch13-16: optically isolated. IN+ input voltage range = 5 V to 24 V, Load current = 2 mA @5 V or 10 mA@24 V (typical). See

figure 2.

• GPI outputs ch1-10: Open collector outputs. Maximum current draw 75 mA (per channel). Withstand a voltage of 12 V. See figure 3.

• GPI +5 V outputs: Output voltage = 5 V +/- 0.25 V, Maximum surpply current in total = 300 mA. See “6-10. Pin assignment / GPI

[OUTPUT] connector.”

6-8. EXTERNAL DC INPUT CHARACTERISTICS

6-9. General specifications

Terminal Format Level Connector

Balanced /

Unbalanced

GPI

IN — —

D-SUB Connector

25P (Female)

—

OUT — —

WORD CLOCK

IN — TTL/75Ω terminated

BNC —

OUT — TTL/75Ω

Terminal Connector

BACKUP DC INPUT XLR-4-32 type

Power Requirements

(wattage)

45W

Power Requirements for MAIN AC INPUT

(voltage and hertz)

US/Canada: 120V 60Hz

Japan: 100V 50/60Hz

China: 110 – 240V 50/60Hz

Korea: 220V 60Hz

Other: 110 – 240V 50/60Hz

Power Requirements for BACKUP DC INPUT

12V-14.8V, 4A

Temperature Range

Operating temperature range: 0 – 40°C

Storage temperature range: -20 – 60°C

Dimensions (W x H x D)

480 x 88 x 368 mm (18-7/8" x 3-1/2" x 14-1/2")

Net Weight

7.0 kg (15.43 lb)

Included Accessories

Power cable, Ferrite core, Getting Started, Rubber stoppers (4)

+5V

GND

IN+

IN-

Figure 1: GPI Inputs ch1-12 Figure 2: GPI Inputs ch13-16

OUT

COM

Figure 3: GPI outputs

6-10. Pin assignment

ANALOG [INPUT] connector

ANALOG [OUTPUT] connector

[AES/EBU] connectors

[BACKUP DC INPUT] connector

Signal

Input Ch

Open GND

12345678

Hot

24 10 21 7 18 4 15 1

2, 5, 8, 11, 16, 19, 22,

Cold

1223920617314

Signal

Output Ch

Open GND

12345678

Hot

24 10 21 7 18 4 15 1

2, 5, 8, 11, 16, 19, 22,

Cold

1223920617314

Signal

Data In Ch Data Out Ch

Open GND1-2 3-4 5-6 7-8 1-2 3-4 5-6 7-8

9-10 11-12 13-14 15-16 9-10 11-12 13-14 15-16

Hot

12345678

9,11

10, 12, 13, 22, 23, 24,

Cold

14 15 16 17 18 19 20 21

Signal Open GND +12V

2, 3 1 4

113

1425

113

1425

113

1425

GPI [INPUT] connector

GPI [OUTPUT] connector

Signal

GPI Input Channel

Open GND

12345678910111213141516

IN, IN+

11421531641751861920212223

11, 12

24, 25

IN+

78910

Signal

GPI Output Channel

Open GND +5V

12345678910

OUT

12345678910

COM

14 15 16 17 18 19 20 21 22 23

113

1425

113

1425

6-11. Dimensions

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha

website then download the manual file.

Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die neueste Version

der Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter.

Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date de publication du manuel. Pour

obtenir la version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du manuel concerné.

El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último manual, acceda

al sitio web de Yamaha y descargue el archivo del manual.

O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual mais recente,

acesse o site da Yamaha e faça o download do arquivo do manual.

Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere la versione più

recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente.

В содержании данного руководства приведены последние на момент публикации технические характеристики. Для получения

последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с руководством.

480

347.5

7.5

430

355

368

9.5

358.5

Unit: mm

Sivu latautuu...

Yamaha MMP1 Getting Started

Merkki: Yamaha

Malli: MMP1

Luokka: Supplementary music equipment

Tyyppi: Getting Started

Lataa PDF

raportti

muilla kielillä

polski: Yamaha MMP1
Türkçe: Yamaha MMP1
English: Yamaha MMP1
čeština: Yamaha MMP1
svenska: Yamaha MMP1
русский: Yamaha MMP1
italiano: Yamaha MMP1
Deutsch: Yamaha MMP1
português: Yamaha MMP1
dansk: Yamaha MMP1
français: Yamaha MMP1
español: Yamaha MMP1
Nederlands: Yamaha MMP1
română: Yamaha MMP1

Yamaha MMP1 Getting Started

Yamaha MMP1 Getting Started

muilla kielillä

Aiheeseen liittyviä papereita