Yamaha THR10II pikaopas

Kategoria
Bluetooth music receivers
Tyyppi
pikaopas

Tämä käsikirja sopii myös

THR30II Wireless THR10II Wireless THR10II Reference Manual 1
EN
Reference Manual
Guitar Amplifier
Contents
Introduction ...........................................................................2
Main Features ............................................................................. 2
Accessories ................................................................................ 2
Names and Functions ..........................................................3
Control Panel .............................................................................. 3
Rear Panel .................................................................................. 6
Connection ............................................................................7
Connection Example (on THR30II Wireless) .............................. 7
Power ......................................................................................... 8
Connecting to guitar by wireless (THR-II Wireless only) ............ 9
Connecting to a smart device ................................................... 10
Connecting to a computer ........................................................ 12
Troubleshooting .................................................................14
Specifications .....................................................................16
Technical Specifications ........................................................... 16
THR30II Wireless, THR10II Wireless*
Power Button LED status list ............................................ 17
Signal Flow Diagrams ............................................................... 18
Amp Modeling List .................................................................... 19
THR30II Wireless THR10II Wireless THR10II Reference Manual 2
Thank you for purchasing this Yamaha product.
This product is an exceptionally versatile and compact guitar amplifier designed for use in your home, rehearsal
spaces, and other places—virtually anywhere you want it!
We recommend that you read this manual carefully so that you can fully take advantage of the advanced and
convenient functions of the product. We also recommend that you keep this manual for future reference.
Main Features
Sophisticated guitar amplifier utilizing advanced amp modeling, made possible with Yamaha’s origi-
nal VCM technology.
Built-in wireless receiver works with the Line 6 Relay G10T transmitter for wireless use (THR30II Wire-
less and THR10II Wireless only).
Bluetooth® capability enables playing music and editing sound settings from a smart device and a
computer.
Built‐in rechargeable battery enables use without power adaptor (THR30II Wireless and THR10II Wire-
less only).
Yamaha’s original Extended Stereo technology enables an exceptionally wide stereo image, much
wider than the units compact size.
The audio interface capability enables recording your guitar to computer via USB.
Incorporates a chromatic tuner.
* What is VCM Technology?
An original physical modeling technology developed by Yamaha, VCM Technology reproduces the characteristics of analog
circuitry at the component level to accurately reproduce the sound of the modeled equipment.
Accessories
•Power Adaptor
•Quick Guide
Safety Instructions Sheet
Service Offices list
Cubase AI Download Information
* In this document, the THR30II Wireless, THR10II Wireless and THR10II are collectively called THR-II.
The THR30II Wireless and THR10II Wireless are called THR-II Wireless.
* The LINE 6 wireless transmitters described in this document refer to the Relay G10T and the Relay
G10TII (hereinafter abbreviated as the Relay G10T.)
Introduction
THR30II Wireless THR10II Wireless THR10II Reference Manual 3
Control Panel
q [ ] (Power Button) / Power Button LED
This is the unit’s power button.
When the power is ON, the Power Button LED, the lamp corresponding to the selected amp type and the
Power Lamp in the speaker cabinet light up.
w LED Display
Indicates each of the THR-II’s settings and conditions.
e [TAP/TUNER] button
Tuner Function
Holding the switch for 1 second engages the tuner function and lights the indicators.
The tuner is calibrated to A4=440Hz. Tune the guitar until the desired pitch appears in the LED display.
When only the circle ( ) in the center of the display is visible, tuning is accurate.
Press the [TAP/TUNER] button (less than one second) to turn OFF the tuner function.
* When the tuner function is set to ON, the guitar sound to the main speaker, [PHONES] jack, and [USB] jack is muted. The
sounds from the [AUX] jack, [USB] jack and Bluetooth are output to the main speaker and [PHONES] jack.
Names and Functions
q
w
!5
!6
!7
e y u i o !0
!1 !2 !3 !4
r
!8
q
w
!5
!6
!7
e t y u i o !0 !1 !2 !3 !4r
!8 !9
THR30II Wireless
THR10II Wireless
THR10II
*
THR10II Wireless only
Pitch is low Pitch is highIn tune
THR30II Wireless THR10II Wireless THR10II Reference Manual 4
Names and Functions
Tap Tempo Function
When an ECHO or ECHO/REV effect is selected with the [ECHO/REV] knob !2 control, the tempo of the
delay can be set by tapping (more than twice) on the switch.
Extended Stereo Setting
Hold the switch for more than three seconds to switch the Extended Stereo* function ON/OFF.
ON: “#” on LED Display w is off (default setting).
OFF: “#” on LED Display w is lit.
* Extended Stereo: The Extended Stereo function produces a much wider stereo field. Extended Stereo affects the sounds
from the [AUX] jack, [USB] jack and Bluetooth as well as the reverb effect.
* The Extended Stereo setting (ON/OFF) is saved when the power is turned OFF.
r [AMP] knob
Selects the amp type. The lamp for the corresponding amp type lights.
* When the power is turned ON, the most recent amp type is selected.
Tips on Creating Sound
Using the [GAIN] knob y and [MASTER] knob u in combination gives you broad control over the sound for
each amp type, except ACO and FLAT. Setting the [GAIN] knob and [MASTER] knob adjusts the amount of
preamp and power amp saturation. Once you have the desired sound, use the [GUITAR] knob !3 to set the
overall volume of the guitar sound.
t [AMP] switch (THR30II Wireless only)
Selects the amp mode. Selects the amp modeling by combination of amp mode and amp type. The [AMP]
knob r lamp lights for the corresponding amp mode color.
For further details of amp modeling settings that can be selected by combining the amp mode and amp type,
refer to the Amp Modeling List (page 19)
y [GAIN] knob
Adjusts the amount of preamp gain. Turn the knob clockwise to increase the amount of gain.
* When ACO is selected with the [AMP] knob r, the modeled sound is a mixture of the front-mic’d sound and pickup sound
of an acoustic electric guitar. (Minimum setting produces the direct pickup sound only. Maximum setting produces the mic
sound only.)
u [MASTER] knob
Adjusts the volume for the guitar sound. Turn the knob clockwise to increase the volume and create power
amp distortion and change in the low-range frequency.
* When BASS, ACO or FLAT is selected with the [AMP] knob r, this only adjusts the volume.
i [BASS] knob
Tone adjustment for the guitar’s sound. Turn the knob clockwise to enhance the low-range frequencies.
o [MIDDLE] knob
Tone adjustment for the guitar’s sound. Turn the knob clockwise to enhance the mid-range frequencies.
!0 [TREBLE] knob
Tone adjustment for the guitar’s sound. Turn the knob clockwise to enhance the high-range frequencies.
!1 [EFFECT] knob
Selects one of four different effects: CHORUS, FLANGER, PHASER, or TREMOLO. Turn the knob clockwise
to increase the amount of each effect.
* Turn the knob fully counterclockwise to set the effect OFF.
THR30II Wireless THR10II Wireless THR10II Reference Manual 5
Names and Functions
!2 [ECHO /REV] knob
Selects one of four different effects: ECHO (tape echo), ECHO/REV (tape echo/reverb), SPRING (spring
reverb), and HALL (hall reverb).
Turn the knob clockwise to increase the amount of each effect.
* Turn the knob fully counterclockwise to set the effect OFF.
* When ECHO or ECHO/REV is selected, the [TAP/TUNER] button
e can be used to set the delay time.
!3 [GUITAR] knob
Adjusts the overall volume of the guitar sound.
* This knob’s setting has no effect on the signal sent to the [USB] jack @0.
* The volume output to the [LINE OUT] [L] [R] jack (THR30II Wireless only) is constant regardless of the setting of the [GUI-
TAR] knob.
!4 [AUDIO] knob
Adjusts the audio playback volume for audio from the computer connected to the [USB] jack @0, an audio
device connected to the [AUX] jack !7, or a smart device connected by Bluetooth (page 10).
!5 [INPUT] jack
This is a standard phone jack used to connect a guitar to the THR-II.
* Connecting the Relay G10T to the [INPUT] jack starts charging that device automatically. (THR-II Wireless only)
* The optimal channel is set automatically by connecting the Relay G10T to the [INPUT] jack for at least 10 seconds. (THR-II
Wireless only)
!6 [PHONES] jack
This is a stereo mini phone jack used to connect stereo headphones to the THR-II.
* Speaker sound is muted when a plug is inserted into the [PHONES] jack.
!7 [AUX] jack
This is a stereo mini phone jack used to connect an external audio device to the THR-II.
* The signal received at the [AUX] jack is not sent to the [USB] jack @0.
!8 [USER MEMORY] [1] [2] [3] [4] [5] button
Saves up to five sets of amp section controller settings (GAIN, MASTER, BASS, MIDDLE, TREBLE, EFFECT,
ECHO/REV).
Press and hold the number of the desired [USER MEMORY] button for saving your settings to (about 2 seconds).
The save operation is complete when the memory number for the button being pushed appears in the
LED Display
w
. Press one of the numbered buttons (less than 2 seconds) to recall the saved settings.
* On the THR10II Wireless and THR10II, enable Bluetooth by pressing the [USER MEMORY] button [4] and [5] simultane-
ously.(Same as [Bluetooth] button
!9)
!9 [Bluetooth]button (THR30II Wireless only)
Set the Bluetooth. Press and hold for three seconds to activate Bluetooth pairing. The LED display w will flash
in green. For further details, refer to the section “Connecting to a smart device” on page 10.
THR30II Wireless THR10II Wireless THR10II Reference Manual 6
Names and Functions
Rear Panel
@0 [LINE OUT] [L] [R] jack (THR30II Wireless only)
These are standard phone jacks used to output line level audio signals.
For connection to external devices with line level signals.These jacks can be connected to phone-type (bal-
anced/unbalanced) plugs.
@1 [USB] jack
This jack is used to connect THR-II to a computer via a USB cable.
@2 [15V] DC IN connector
Connects the supplied power adaptor.
@0
@1
@2
LR
About the Default Settings
To reset all contents stored in the user memory, switch on the power while holding down [USER MEM-
ORY] buttons [1], [3], and [5].
NOTICE
All contents stored in the user memory will return to factory defaults when the unit is initialized.
Hold down switches [1], [3], and [5].
Switch on the power.
THR30II Wireless THR10II Wireless THR10II Reference Manual 7
The THR-II can be used either with a conventional wired connection with an appropriate cable, or with a wireless
connection.
Connection Example (on THR30II Wireless)
Make sure that all devices to be connected to the unit by cable are turned off.
When connecting the unit to an external device, always use an appropriate cable that matches the
jack’s specifications and connect it securely.
Precautions for using the USB jack
Make sure to follow the points at next page when connecting a computer to the THR-II USB jack, to avoid loss
of data by the computer and prevent the THR-II from freezing or shutting down.
Connection
LR
* The illustrations and LCD screens as shown in this manual are for instructional purposes only,
and may appear somewhat different from those on your instrument.
NOTE
If a cable is connected to the INPUT
jack, the wireless guitar receiver can-
not be used.
• Playing music/audio
NOTE
Make sure to adjust the devices level
appropriately to avoid distortion.
• Wireless tone editing with the iOS/
Android app (THR Remote).
• Wireless control with a third-party
Bluetooth footswitch (via THR
Remote).
Wireless
Connection
Audio output from
an audio player or
computer
Computer, Tablets and Smartphones
USB Cable
Power Adaptor
LED display
When connecting Blue-
tooth, check LED light-
ing in this area.
• Order for turning the power on
THR30II Wireless Mixer Amp (or powered speaker)
• Order for turning the power off
Amp (or powered speaker) Mixer THR30II Wireless
External Audio Devices
Power
Outlet
Bluetooth
THR30II Wireless THR10II Wireless THR10II Reference Manual 8
Connection
NOTICE
Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.
Be sure to wake the computer from suspended/sleep/standby mode before connecting a computer
to the USB jack.
Always quit all applications that are running on the computer before connecting or disconnecting
the USB cable and set the volume output on the computer to its minimum level.
When connecting or disconnecting the USB cable, be sure to set the OUTPUT controls ([GUITAR]
knob and [AUDIO] knob) on the THR-II to their minimum levels.
Wait at least 6 seconds between connecting or disconnecting the USB cable.
Power
The THR-II Wireless can operate on either DC power (via the power adaptor) or with the built‐in rechargeable
battery. The THR10II can operate on DC power (via the power adaptor).
* When you use the THR-II Wireless with the built-in rechargeable battery, the maximum output volume is reduced. (page 16)
When using the power adaptor
Connect the supplied power cord to the power adapter. Connect the supplied power adaptor to the [15V] DC IN
jack located on the rear panel of the THR-II. Connect the AC plug to a power outlet.
* Follow the bundled Safety Instruction Sheet before making connections.
Turning the power on and off
Press the [ ] power button on the top of THR-II for one second to turn the power on. The LED of the power
button lights when turning the power button on. The LED of the THR-II Wireless lights in green while charging.
Otherwise, it lights in red.
* Follow the bundled Safety Instruction Sheet before making connections.
Checking the battery level (THR-II Wireless only)
Press the [ ] button on top of the THR-II Wireless for less than one second to check the battery level. The
remaining battery capacity is displayed in four levels of 3, 2, 1 and L (Low).
Power Adaptor
(supplied)
Power Outlet
DC IN Jack
DC plug
the supplied power cord
Battery full No battery remaining
THR30II Wireless THR10II Wireless THR10II Reference Manual 9
Connection
Charging the built-in battery (THR-II Wireless only)
Connect the supplied power adaptor to the DC IN jack located on the rear side of the THR-II Wireless. The LED
of the power button lights in green while charging.
* For further details of the Power Button LED status, refer to the Power Button LED status list (page 17).
NOTICE
When you use the THR-II Wireless in an environment of extreme temperatures, charging may not be
possible.
Charge the built-in rechargeable battery once every six months to maintain the function.
Charging the Relay G10T (THR-II Wireless only)
Connect the Relay G10T *
1
to the [INPUT] jack located on the top of the THR-II Wireless. The built‐in recharge-
able battery starts *
2
charging automatically. If you have disconnected the Relay G10T from the [GUITAR] jack of
the THR-II Wireless and want to resume charging, wait for more than two seconds before reconnecting the
device to the [GUITAR] jack.
*
1
Refer to the manual of Relay G10T for explanations of the LED display indications on the Relay G10T.
*
2
If the supplied power adapter is not connected to the THR-II Wireless, charging of the Relay G10T will not start.
NOTICE
After charging, unplug the Relay G10T from the THR-II Wireless.
When the THR-II Wireless is turned off and the power adapter is connected, the Relay G10T is
charged by simply connecting. However, the THR-II Wireless is set to stop supplying power to the
Relay G10T when the Relay G10T charging is finished. In this state, leaving the Relay G10T con-
nected to the THR-II Wireless may result in depletion of the Relay G10T’s battery power. Turn off the
THR-II Wireless’s ECO setting to prevent this.
Changing the Relay G10T’s ECO setting *
1
*
2
1. Switch on the power of THR-II Wireless
2. Switch off the power of THR-II Wireless while holding the [TAP/TUNER] button
*
3
*
1
You can change the ECO setting from the THR Remote.
*
2
ECO on and ECO off are toggle. When you change the ECO setting, perform the steps 1 to 2 again.
*
3
Since the ECO setting changes to ECO off when charging is started on the Relay G10T, “C” will appear on the LED
display.
Connecting to guitar by wireless (THR-II Wireless only)
The THR-II Wireless can connect with the Relay G10T by wireless. Moreover, the optimal channel is set auto-
matically by connecting the Relay G10T to the [INPUT] jack located on the top of the THR-II Wireless for at least
10 seconds. For details on wireless connection, refer to the reference manual.
Switch off the power while
holding the [TAP/TUNER]
button.
THR30II Wireless THR10II Wireless THR10II Reference Manual 10
Connection
Connecting to a smart device
By connecting a smart device to the THR-II, you can:
Play audio files from a smart device via Bluetooth.
Edit effect and tone controls from a smart device.
Playing audio files on a smart device via Bluetooth
To play audio from a smart device via Bluetooth, configure Bluetooth on the smart device while in the pairing
mode.
Setting the THR-II to pairing mode
1. Check that the at the top of the LED DISPLAY is unlit (disconnected).
2. Press and hold the [Bluetooth] button* located on the top of the THR-II for three seconds.
3. Check that the LED DISPLAY flashes in green (pairing mode).
Configuring Bluetooth on the smart device
4. Complete the Bluetooth configuration of the smart device within 3 minutes after entering pairing mode.
* For details on Bluetooth configuration, refer to the manual of your smart device.
5. Check that the LED DISPLAY is lightning in green (connected).
Confirm sound output from the THR-II by playing music from the smart device.
NOTE
When the Bluetooth connection record remains on both the THR-II and smart device, they will
reconnect automatically when the THR-II power is turned on.
Play audio from the
smart device.
5. Check that the LED
is lit in green
(connected).
4. Complete the Blue-
tooth configura-
tion within 3
minutes.
3. Check that the LED flashes in
green (pairing mode).
1.Unlit
(disconnected)
2. Press and hold the
Bluetooth button* for
three seconds (pairing).
*
On the THR10II Wireless and THR10II,
enable Bluetooth by pressing the [USER
MEMORY] button [4] and [5] simultane-
ously.
Press the Bluetooth
button* once
then disconnected.
(reconnect)
Press the Bluetooth
button*.
(disconnect)
THR30II Wireless THR10II Wireless THR10II Reference Manual 11
Connection
Editing effects and tone controls on a smart device
Install the THR Remote app to the smart device to allow editing of effects and tone controls on that device.
Installing THR Remote (Android, iOS)
1. Access the app distribution service on the smart device.
Android devices: Google Play*
iOS devices: App Store
2. Search for the THR Remote app.
3. Download and install the THR Remote app following the onscreen instructions.
Configuring Bluetooth MIDI
1. Start the THR Remote.
2. Touch the Bluetooth icon on the display.
3. Connect to LE_THRII following the onscreen instructions.
Starting the THR Remote app
Start the THR Remote app on the smart device.
Press the desired [USER MEMORY] button for 2 seconds to save the settings made with THR Remote to the
THR-II’s built-in user memory (page 5).
For connecting Android devices, refer to “Smart Device Connection Manual for Android.
For connecting iOS devices, refer to “iPhone/iPad Connection Manual.
Yamaha Downloads. https://download.yamaha.com/
* Google Play and the Google Play logo are trademarks of Google LLC.
THR30II Wireless THR10II Wireless THR10II Reference Manual 12
Connection
Connecting to a computer
Connecting a computer to the THR-II makes the following possible:
Playing back audio files from a computer through the THR-II.
Recording with Cubase AI.
Editing amp and effect settings using the THR Remote desktop editor.
Playing back audio files from a computer through the THR-II.
Configuring and Operating
Select the model name (THR30II WIRELESS, THR10II WIRELESS, THR10II) of the connected THR-II as the
computers audio output setting.
Windows
Control Panel Sound “Sound” tab
Macintosh
System Preferences Sound Output” tab
Connect the computers USB connector to the USB connector on the THR-II as shown in the diagram below.
You can play a guitar along to the audio played on the computer.
Use the [AUDIO] knob to adjust the volume of the audio played from a computer.
USB Connection diagram
[AUDIO] knob
Playback an
audio file on the
computer.
Guitar sound
+
audio playback
[USB] jack
THR30II Wireless THR10II Wireless THR10II Reference Manual 13
Connection
Recording with Cubase AI
Installing Cubase AI
A download access code for Cubase AI music production software is included with the THR-II. Cubase AI
enables you to record, edit, mix and play back audio through your THR-II.
Cubase AI System Requirements
For the latest information, refer to the Steinberg website below.
https://www.steinberg.net/
Installing Cubase AI
To install Cubase AI, an active Internet connection is required. Follow the instructions provided in the “Cubase
AI Download Information” sheet to download, install and activate the software.
Connecting to the THR-II
Connect the computers USB connector to the USB connector on the THR-II as shown in the diagram below.
(See the USB Connection diagram on page 12.)
* For more information on operating, refer to the Cubase AI’s Help Menu (see the illustration below).
Editing effects and tone controls on a computer
Installing the THR Remote app (Windows, Mac)
1. Access the following website and extract the THR Remote file after downloading.
https://download.yamaha.com/
* Check the above website for information on system requirements.
* The THR Remote may be updated without notice. Check the above website for the latest details and updates.
2. Install the THR Remote app to your computer.
Configuring and Operating after Installing
Connect the computer’s USB connector to the [USB] connector on the THR-II as shown in the diagram below.
(See the USB Connection diagram on page 12.)
Press the desired [USER MEMORY] button for 2 seconds to save the settings made with THR Remote to the
THR-II’s built-in user memory (page 5).
THR30II Wireless THR10II Wireless THR10II Reference Manual 14
No power
Connect the power adaptor properly (see page 8).
Make sure that the THR-II Wireless been prop-
erly charged, when the power adapter is discon-
nected (see page 8).
No sound
No guitar sound is output (wired connection)
Connect the guitar to [INPUT] jack properly (see
page 7).
Make sure that the volume control on the guitar
is turned up properly.
Make sure that the [GAIN] knob, [MASTER]
knob and [GUITAR] knob are not set to mini-
mum (see pages 4, 5).
When the [AMP] knob is set to CLEAN, make
sure that all of the [BASS] knob, [MIDDLE] knob
and [TREBLE] knobs are not set to minimum
(see page 4).
Dont connect the headphones to [PHONES]
jack to outputs from the speaker on THR-II (see
page 5).
Make sure that the COMPRESSOR Level is not
set to 0 on the THR Remote app (see pages 11,
13).
Set the Tuner function OFF (see page 3).
Make sure that the cable connecting the guitar
is not damaged.
No guitar sound is output (wireless con-
nection)
Use the Relay G10T. THR-II Wireless cannot
connect to any guitar wireless transmitter other
than the Relay G10T.
Connect the Relay G10T to the INPUT jack
located on the top of the THR-II Wireless for at
least 10 seconds. The appropriate channel is
set automatically.
Make sure that the volume control on the guitar
is turned up.
Set the Tuner function OFF (see page 3).
No audio sound is output by Bluetooth
Confirm the status of LED display. When the
LED is unlit or flashing in green, the devices are
not connected via Bluetooth (see page 17).
When the Bluetooth configuration on the smart
device is ON, turn it OFF once and configure
"Playing audio files on a smart device via Blue-
tooth" (see page 10).
Delete the Bluetooth registration once on the
Bluetooth configuration screen on the smart
device and configure "Playing audio files on a
smart device via Bluetooth" (see page 10).
Move the smart device and the THR-II closer
together.
Turn off the power of the THR-II. (see page 8)
Restart the smart device.
* For details on Bluetooth configuration, refer to the
manual of the smart device.
Disconnect any other Wi-Fi and Bluetooth
devices. The connection may be broken due to
the influence of other nearby Wi-Fi or Bluetooth
devices.
No audio sound is output from a computer
by USB connection
Connect the USB cable properly (see page 12).
Confirm the configuration of the audio output
port on the computer (see page 12).
Confirm the configuration of the computer on
the computer or that audio is not muted on the
application.
Make sure the [AUDIO] knob is turned up (see
page 5).
Make sure the USB cable connecting the
devices is not damaged.
No audio sound is output from an external
device by AUX connection
Connect the cable to the external device prop-
erly (see page 7).
Make sure that the volume control on the exter-
nal device is turned up.
Make sure the [AUDIO] knob is turned up (see
page 5).
Make sure the cable connecting the devices is
not damaged.
Troubleshooting
THR30II Wireless THR10II Wireless THR10II Reference Manual 15
Others
Tap Tempo cannot be set
Select ECHO or ECHO/REV. The tap tempo can-
not be set with SPRING or HALL (see page 4).
A “#” appears in the LED display
When Extended Stereo is set to OFF, a “#”
appears in the LED display (see page 4).
THR-II Wireless cannot be charged
Keep the THR-II Wireless at room temperature
and dont use it until the built-in rechargeable
battery reaches a suitable temperature. If charg-
ing cannot be performed after a sufficient time,
there may be a problem with the built-in
rechargeable battery. If the problem persists,
consult your Yamaha dealer (see page 17).
Relay G10T cannot be charged
When Relay G10T is disconnected from the
[INPUT] jack, connect to the [INPUT] jack on
THR-II Wireless again after 2 seconds.
Volume is low
Keep the THR-II Wireless at room temperature
and dont use it until the built-in rechargeable
battery reaches a suitable temperature.
For safety reasons, the built-in rechargeable
battery is designed to limit the volume when the
built-in rechargeable battery's temperature rises.
The built-in rechargeable battery charge
does not last
THR-II Wireless's built-in rechargeable battery
may have reached the end of its life. If the prob-
lem persists, consult your Yamaha dealer.
Charge the battery every six months to maintain
the battery power function.
The built-in rechargeable battery has a limited life-
time. The capacity decreases gradually with the
number of times of use and the passage of time.
The lifetime of the built-in rechargeable battery
depends on the storage method, usage and envi-
ronment.
THR30II Wireless THR10II Wireless THR10II Reference Manual 16
Technical Specifications
Digital Section
Built-in Amp Simulations
CLEAN, CRUNCH, LEAD, HI GAIN, SPECIAL, BASS,
ACO
*, FLAT
There is an amp mode MODERN, BOUTIQUE, and
CLASSIC for each amp type (THR10II Wireless and
THR10II can switch the amp mode by THR Remote)
* Mic simulation
Built-in Effects
CHORUS, FLANGER, PHASER, TREMOLO
ECHO, ECHO/REVERB, SPRING REVERB, HALL
REVERB
In addition to the above, Room and Plate reverbs are
also available in the THR Remote editor.
COMPRESSOR
*
NOISE GATE*
*
Only available from THR Remote.
Built-in Chromatic Auto Tuner
Knob/Switch
AMP, GAIN, MASTER, BASS, MIDDLE, TREBLE,
EFFECT, ECHO/REV, GUITAR, AUDIO, USER MEM-
ORY button x 5, TAP/TUNER button, Amp switch*,
Bluetooth button*
* Only THR30II Wireless
Display
LED × 1
Connections
INPUT (Standard Monaural Phone Jack, Unbalanced),
LINE OUT (Standard Jack, Balanced/Unbalanced),
PHONES (Stereo Mini Jack),
AUX (Stereo Mini Jack),
USB TYPE B,
DC IN (15V)
A/D Converter
24-bit + 3 Bit Floating
D/A Converter
24-bit
Sampling Frequency
48 kHz
Memory Allocations
User Memory: 5
Input Level
GUITAR IN : -10 dBu
AUX IN : -10 dBu
PHONES Output Level
10 mW
Rated Output
THR30II Wireless: 30 W (15 W + 15 W)
THR10II Wireless, THR10II: 20 W (10 W + 10 W)
Maximum output during built-in recharge-
able battery operation
THR30II Wireless, THR10II Wireless:
15 W (7.5W + 7.5W)
Power Source
Power Adaptor or built-in rechargeable battery
Power Adaptor (YNT345-1530)
Built-in rechargeable battery
Battery life*: About 5 hours
* Depends on usage situation
Power Consumption
THR30II Wireless, THR10II Wireless: 22 W
THR10II: 11 W
Dimensions (W x H x D)
THR30II Wireless:
420 x 195 x 155 mm (16.5” × 7.7” × 6.1”)
THR10II Wireless, THR10II:
368 x 183 x 140 mm (14.5” × 7.2” × 5.5”)
Weight
THR30II Wireless: 4.3 kg (9 lbs. 8 oz.)
THR10II Wireless: 3.2 kg (7 lbs)
THR10II: 3.0 kg (6 lbs. 1 oz.)
Accessories
• Power Adaptor (YNT345-1530)
• Quick Guide
• Safety Instructions Sheet
• Service offices list
• Cubase AI Download Information
Bluetooth
Bluetooth Version: Bluetooth Ver. 4.2
Supported Profile: A2DP
Compatible Codec: SBC
RF Outout Power: Bluetooth class 2
Maximum Communication Range: 10m (33ft) (without
obstacles)
* The contents of this manual apply to the latest
specifications as of the publishing date. To
obtain the latest manual, access the Yamaha
website then download the manual file. Since
specifications, equipment or separately sold
accessories may not be the same in every locale,
please check with your Yamaha dealer.
Specifications
THR30II Wireless THR10II Wireless THR10II Reference Manual 17
Specifications
THR30II Wireless, THR10II Wireless* Power Button LED status list
* Since the THR-10II does not have a built-in rechargeable battery, the power button LED status is
only red (ON) and off (OFF).
When not using the power adaptor
The power is ON
The power is OFF
When using the power adaptor
Charging
The battery is full and the power is ON
The battery is full and the power is OFF
Red
Unlit
Red
Unlit
Charging error indication
When the power is on Indicates charging error
When the power is off Indicates charging error
If the built-in rechargeable battery has a charging error, immediately turn off the THR-II Wireless power,
unplug the power adapter, and consult your Yamaha dealer.
Flashes
(green  red)
Flashes
(green  unlit)
THR30II Wireless THR10II Wireless THR10II Reference Manual 18
Specifications
Signal Flow Diagrams
+
Guitar In
Extended Stereo
Bluetooth In
USB In
Speakers &
Headphones Out
USB Out
Line Out
Wet
GUITAR
Knob
Sync
Compressor
(FX1)
Speaker
Simulator

Simulator

(FX2)
Delay
(FX3)
AUX In
Reverb
(FX4)
AUDIO
Knob
USB
Dry
Output gain
App. control
Noise
Gate
Mix gain
App. control
Sync
Direct
Switch
THR30II Only

Variable gain
THR30II Wireless THR10II Wireless THR10II Reference Manual 19
Specifications
Amp Modeling List
Mode Amp Type Description
Classic
Clean
A low-gain preamp for sparkling American-style cleans, with 6L6 tubes in the output stage
for brightness and a strong midrange.
Crunch
EL84 power tubes in a true Class-A configuration with a highly responsive EQ for rich,
complex harmonic tones and warm overdrive. Inspired by British chime.
Lead
A low-gain preamp with an EL34-based power section that breaks into classic British over-
drive as the master volume is pushed.
Hi Gain
Powerful modern distortion that fills out as the high-gain preamp is pushed. Tread carefully
after 12 o'clock.
Special
12AX7 and 6L6 tubes in pursuit of the "Brown" sound. Set the gain around 11 o'clock for
classic rock crunch, or crank it for saturated rhythm tones.
Bass Woody, vintage tone with late breakup.
Acoustic
Designed for acoustic-electric guitar, modeling the response of a boutique condenser
microphone.
Flat
A neutral tone with no amp or speaker modeling. Great for connecting other instruments to
your THR.
Boutique
Clean
A low-watt EL34 design. Turning up the preamp gain will thicken up the cleans, then push
into bluesy overdrive.
Crunch
A deceptively simple amp circuit with just a single 12AX7 and EL84. A full, no-frills tone
that is highly responsive to picking dynamics.
Lead
A version of the Classic/Lead circuit, modified for extra gain with a darker tone and
scooped mids.
Hi Gain
ECC83s into 6L6s for high gain with a highly responsive EQ, inspired by German engineer-
ing.
Special
Four 12AX7 preamp tubes into 6L6 output tubes. Tight, fast tracking for crushing high-
gain.
Bass Full, modern tone that breaks into a fuzz-like overdrive when pushed hard.
Acoustic
Designed for acoustic-electric guitar, modeling the response of a boutique tube micro-
phone.
Flat
A neutral tone with no amp or speaker modeling, and a slight bass boost. Great for con-
necting other instruments to your THR.
Modern
Clean
A boutique, low-watt EL84 design that adds fullness and sustain as the master volume is
turned up. A great match for neck pickups.
Crunch
A mid-volume boutique design with 6550 power tubes. Listen for tight bass response and a
singing sustain.
Lead
A high-gain design with 12AX7s into EL34s, for the tone that defined 1980s hard rock and
heavy metal.
Hi Gain
A boosted version of the Classic/Special amp, with even more gain for aggressive rhythms
or searing leads.
Special
A classic overdrive circuit before the preamp tightens low-frequency response and provides
even more gain. Ideal for extended-range guitars.
Bass Vintage voicing with early breakup for overdrive that works well with bass or guitar.
Acoustic
Designed for acoustic-electric guitar, modeling the response of a boutique dynamic micro-
phone.
Flat
A neutral tone with no amp or speaker modeling, and a slight mid scoop. Great for con-
necting other instruments to your THR.
THR30II Wireless THR10II Wireless THR10II Reference Manual
Manual Development Department
© 2019 Yamaha Corporation
Published 4/2021 PO-B0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Yamaha THR10II pikaopas

Kategoria
Bluetooth music receivers
Tyyppi
pikaopas
Tämä käsikirja sopii myös