Compact Disc Player
Lecteur Compact Disque
CD
X-
596
/4
96/396
OWNER’S MANUAL
MODE D’EMPLOI
U C A
• Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating
instructions should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other
instructions should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a
swimming pool, etc.
6 Carts and Stands – The unit should be used only with
a cart or stand that is recommended by the
manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause
the unit and cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be
situated on a bed, sofa, rug, or similar surface, that
may block the ventilation openings; or placed in a built-
in installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the
operating instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into
the inside of the unit.
15 Damage Requiring Service – The unit should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into
the unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet
damaged.
16 Servicing – The user should not attempt to service the
unit beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be
taken so that the grounding or polarization is not
defeated.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
IMPORTANT
Please record the serial number of this system in the
space below.
Model:
Serial No.:
The serial number is located on the rear of the main
unit.
Retain this Owner’s Manual in a safe place for future
reference.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that lets
the sound come through loud and clear without annoying
blaring or distortion – and, most importantly, without
affecting your sensitive hearing.
Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you
to avoid prolonged exposure from excessive
volume levels.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies
and, if not installed and used according to the
instructions found in the users manual, may cause
interference harmful to the operation of other
electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
CAUTION............................................1
NOTES ABOUT DISCS ...................... 2
FEATURES .........................................3
UNPACKING....................................... 3
NOTES ABOUT THE REMOTE
CONTROL .......................................... 4
CONNECTIONS................................. 5
IDENTIFICATION OF COMPONENTS
............................................................ 6
BASIC OPERATION .......................... 8
To pause play .................................. 9
To stop play ..................................... 9
To turn off the power........................ 9
To play directly from the desired track
..........................................................9
To skip to the beginning of the desired
track (SKIP SEARCH) ................... 10
To advance or reverse play rapidly
(MANUAL SEARCH) ..................... 10
Other useful functions.................... 11
RANDOM-SEQUENCE PLAY ......... 13
REPEAT PLAY................................. 13
PROGRAM PLAY ............................ 14
INDEX SEARCH .............................. 15
TRACK PROGRAMMING FOR
RECORDING TO TAPE ................... 16
Automatic tape-programming ........ 16
Manual tape-programming ............ 18
Random sequential tape-
programming ................................. 19
Automatic searching for the peak
level on a disc................................ 20
CD SYNCHRONIZED RECORDING
..........................................................21
TROUBLESHOOTING..................... 22
SPECIFICATIONS ........................... 23
CONTENTS
English
E-1
● The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher voltage
than that which is specified is dangerous and may result
in a fire or other type of accident causing damage.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
that which is specified.
● Sudden temperature changes and storage or operation in
an extremely humid environment may cause
condensation inside the cabinet.
CAUTION FOR MOVING THE UNIT
Before moving the unit, first remove the disc from the
unit, press POWER to turn the unit off, and then
disconnect the AC power plug from the wall outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
As the laser beam used in this compact disc player is
harmful to the eyes, do not attempt to disassemble the
cabinet. Refer servicing to qualified personnel only.
For Canadian Customers
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
● To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
● Install your unit in a well ventilated, cool, dry, clean place
— away from windows, heat sources, vibration, dust,
moisture, or cold. To avoid humming sounds, locate the
unit away from other electrical appliances, motors, and
transformers. To prevent fire or electrical shock, do not
expose to rain and water.
● Be sure to allow enough spaces for ventilation at the top,
on left, right, and back sides of this unit.
● Do not operate the unit upside-down. It may overheat,
possibly causing damage.
● Never open the cabinet. If something drops into the set,
contact your dealer.
● Do not use force on switches, knobs or cords.
● When not planning to use this unit for long periods of time
(i.e., vacation, etc.), disconnect the AC power plug from
the wall outlet.
● Grounding or polarization — Precautions should be taken
so that the grounding or polarization of the unit is not
defeated.
● Do not clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
● Be sure to read the “Troubleshooting” section on common
operating errors before concluding that your unit is faulty.
● Do not place another component on top of this unit, as
damage or discoloration on the surface of the unit may
result.
● To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
● When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
● Do not plug the AC power plug to the wall outlet before
you finish all connections.
CAUTION: Read this before operating your unit.
E-2
NOTES ABOUT DISCS
Discs playable with this unit
This compact disc player is designed only for playing
compact discs bearing the marks shown below. Never
attempt to load any other type of disc into the unit. The unit
will also play 8-cm (3-inch) compact discs.
.... Compact discs (digital audio)
The most popular discs for commercially
available audio CDs.
.... CD-RW (ReWritable) digital audio
discs
The discs repeatedly recordable by using
CD recorders for audio recording.
Recorded CD-RW discs can be played
only with CD players which have the
ability to play CD-RW discs.
Notes
● Be sure to use a CD-RW disc made by
a reliable manufacture.
● Be sure to use a CD-RW disc which
has at least one of the following
phrases on the disc or disc case.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
.... CD-TEXT discs
The discs recorded with text data such as
album titles, track titles and artist names.
These discs can be played with ordinary
CD players, however, the text data can be
displayed only with CD players which
have the ability to display such data.
CDX-596 can display text data
recorded on CD-TEXT discs.
Note
This compact disc player may not be able to play some
CD-RW discs or discs on which recording was not made
correctly.
To prevent a malfunction of this unit:
● Do not use any nonstandard shaped
disc (heart etc.) available on the
market because it might damage the
unit.
● Do not use a disc with tape, seals, or paste on it. If
you use such a disc, a disc may get stuck in the unit,
or damage to the unit may result.
Notes about handling compact discs
● Always handle the disc with care so that its surface is not
scratched.
● Compact discs are not subjected to wear during play, but
damage to the disc surface when the disc is being
handled can adversely affect the disc’s play.
● Be sure to use a felt-tip pen or similar writing tool when
writing on the label side of the disc. Do not use a ball-
point pen, pencil, or other hard-tipped writing tool, as
these may damage the disc and may adversely affect the
disc’s play.
● Do not warp discs.
● When a disc is not currently being used, remove it from
the unit and store in an appropriate case.
● When removing or storing a disc, be careful not to
scratch the playing surface.
● Compact discs are not affected by small particles of dust
or fingerprints on their playing surface, but even so they
should be kept clean. Wipe by using a clean, dry cloth.
Do not wipe with a circular motion; wipe straight outward
from the center.
● Do not try to clean the disc’s surface by using any type of
disc cleaner, record spray, anti-static spray or liquid, or
any other chemical-based liquid because such
substances might irreparably damage the disc’s surface.
● Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time because these
might warp or otherwise damage the disc.
No!
To play an 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm/5-inch) CD on top of an 8-cm CD.
English
E-3
Thank you for selecting this YAMAHA compact disc player.
FEATURES
v CD-RW (ReWritable) Disc Playability
* Refer to page 2 for details.
v Program Play
v Random-Sequence Play
v Single Track/Entire Disc Repeat Play
v Automatic Spacing Function
v Track Programming Function Useful for
Recording Tracks Fitted onto Any Length
of Tape
v Automatic Peak Level Search Function
v CD Synchronized Recording
v Adjustable Display Brightness
v Remote Control Capability
v Optical Digital Output
CDX-596 only
v Coaxial Digital Output
v CD-TEXT Data Display Capability
UNPACKING
Remote control RCA pin cable
Battery (size AA, R6, UM-3) x 2
OPEN/
CLOSE
DIMMERSYNCHRO
PEAK
TEXT/
TIME
SPACE
PROGCLEAR
TAPE
RANDOM
REPEAT
32
1
65
4
98
7
INDEX
+
I0
OUTPUT LEVEL
+–
0
Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories.
CDX-596 CDX-496 CDX-396
OPEN/
CLOSE
DIMMERSYNCHRO
PEAK
TIME
SPACE
PROGCLEAR
TAPE
RANDOM
REPEAT
32
1
65
4
98
7
INDEX
+
I0
OUTPUT LEVEL
+–
0
OPEN/
CLOSE
DIMMERSYNCHRO
PEAK
TIME
SPACE
PROGCLEAR
TAPE
RANDOM
REPEAT
32
1
65
4
98
7
INDEX
+
I0
0
E-4
NOTES ABOUT THE REMOTE CONTROL
Battery installation
1. Turn the remote control over and remove the battery
compartment cover by sliding it in the direction of the
arrow.
2. Insert the batteries (AA, R6, UM-3 type) according to the
polarity markings on the inside of the battery
compartment.
3. Close the battery compartment cover.
Battery replacement
If you notice that the remote control must be used closer to
the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
● Use only AA, R6, UM-3 batteries for replacement.
● Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
● Remove the batteries if the remote control will not be used for
an extended period of time.
● If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
Notes
● There should be no large obstacles between the remote control
and the main unit.
● If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type fluorescent lamp etc.), the
remote control might not work properly. In this case,
reposition the main unit to avoid direct lighting.
CDX-396CDX-596, CDX-496
30°
30°
Remote control
sensor
2
1
3
Within approximately
6 m (19.7 feet)
English
E-5
CONNECTIONS
● Before making any connection, switch OFF the power to
the unit and the amplifier or other component.
● Connections should be made to the correct input
terminals of the amplifier or another component.
● If the placement of this unit causes noise to another
equipment, such as a tuner, separate them from each
other.
When the LINE OUT (analog) terminals of
this unit are used ( 1 )
Connect these terminals to the “CD” (or “AUX”) terminals of
the amplifier. For additional details concerning these
connections, refer to the operation instructions of the
amplifier being used.
* Be sure that the left (“L”) and right (“R”) of these terminals are
connected to the corresponding (left and right) terminals of the
amplifier or another component.
When the DIGITAL AUDIO OUT (OPTICAL)
terminal of this unit is used ( 2 )
● Before using this terminal, pull out the terminal’s cover.
● Make the connection from this terminal to the optical
input terminal of an amplifier by using a commercially
available optical fiber cable.
* Use an optical fiber cable that conforms to EIAJ
standards. Other cables might not function correctly.
● Be sure to attach the terminal’s cover when this terminal
is not being used, in order to protect the terminal from
dust.
● This terminal can also be connected to the optical input
terminal of an MD recorder etc. to record CD onto MD
directly.
When the DIGITAL AUDIO OUT (COAXIAL)
terminal of this unit is used ( 3 )
CDX-596 only
Make the connection from this terminal to the digital input
terminal of an amplifier by using a connection cable.
To connect this unit to your amplifier, choose one of the ways listed below.
CD DIGITAL IN
OPTICAL
COAXIAL
LINE OUT DIGITAL AUDIO OUT
OPTICAL COAXIAL
1
RCA pin cable
(included)
1
Optical fiber cable
(not included)
2
Connection cable
(For CDX-596 only; not included)
3
Amplifier
To AC outlet
The shaded part ( ) is provided for CDX-596 only.
CDX-596 and CDX-496 only
●
The level of signals output from any of these terminals
into an amplifier can be adjusted by using the
–
OUTPUT LEVEL
+
buttons.
●
When using the DIGITAL AUDIO OUT (OPTICAL or
COAXIAL) terminal, set the level of signals output into
an amplifier to max. by using the
–
OUTPUT LEVEL
+
buttons.
E-6
FRONT PANEL
● The control functions on the main unit and on the remote
control are virtually identical, with the exceptions below.
IDENTIFICATION OF COMPONENTS
( ) indicates the page number on which the controls are best described.
NATURAL SOUND COMPACT DISC PLAYER
AUTO
DISPLAY OFF
POWER
10
1 2 3 4 5 6 7 8 9 0
SKIP/SEARCH
OUTPUT LEVEL
PHONES
OPEN/CLOSE
NATURAL SOUND COMPACT DISC PLAYER
OPEN/CLOSE
POWER
10
1 2 3 4 5 6 7 8 9 0 SKIP/SEARCH
CDX-396
● / (play/pause) on the main unit has both the
functions of (play) and (pause) on the remote
control.
● SKIP/SEARCH on the main unit has both the
functions of / (skip) and / (search) on
the remote control.
CDX-596, CDX-496
POWER (p. 8)
AUTO DISPLAY OFF indicator CDX-596 only (p. 12)
Display panel
Disc tray (p. 8)
Remote control sensor (p. 4)
PHONES jack (p. 12)
POWER (p. 8)
Remote control sensor (p. 4)
Display panel
Disc tray (p. 8)
The shaded part ( ) is provided for CDX-596 only.
English
E-7
( ) indicates the page number on which the controls are best described.
OPEN/
CLOSE
DIMMERSYNCHRO
PEAK
SPACE
PROGCLEAR
TAPE
RANDOM
REPEAT
32
1
65
4
98
7
INDEX
+
I0
OUTPUT LEVEL
+–
0
TEXT/
TIME
TIME
CDX-596
CDX-496, 396
DIMMER (p. 12)
SYNCHRO (p. 21)
SPACE (p. 12)
TAPE (p. 16)
Numeric buttons (p. 9)
REPEAT (p. 13)
RANDOM (p. 13)
CDX-596 and CDX-496 only
OUTPUT LEVEL (p. 12)
INDEX (p. 15)
CLEAR (p. 15)
PROG (p. 14)
PEAK (p. 20)
OPEN/CLOSE (p. 8)
“pause” (p. 9)
/ “skip” (p. 10)
“stop” (p. 9)
/ “search” (p. 10)
“play” (p. 8)
TEXT/TIME (p. 11)
TIME (p. 11)
The shaded parts ( ) vary between models.
REMOTE CONTROL
E-8
BASIC OPERATION
This manual describes how to operate this unit by using the remote control.
To operate this unit from the front panel, use the corresponding buttons on the front panel.
1 Press POWER to turn on the power.
2 Press OPEN/CLOSE to open the disc tray, and load
a disc.
3 Press OPEN/CLOSE to close the disc tray.
4 Press (or ) to begin play.
Play will begin from the first track of the disc.
Display information
CDX-596
CDX-496, CDX-396
NATURAL SOUND COMPACT DISC PLAYER
POWER
1
OPEN/
CLOSE
DIMMERSYNCHRO
PEAK
SPACE
PROGCLEAR
TAPE
2
3
RANDOM
REPEAT
2, 3
4
POWER
OPEN/
CLOSE
OPEN/
CLOSE
1 Shows the track number selected or being played.
2 Displays the numbers that correspond to the numbers
of tracks (as high as number 20) on the disc. After each
track is played, its corresponding number disappears so
the number of remaining tracks (and their numbers) can
be seen at a glance.
3 CDX-596 and CDX-496
only
Shows the level of signals output into an amplifier or the
headphone level adjusted by pressing
–
OUTPUT
LEVEL
+.
4 Shows the time displays. (Refer to “Changing displays”
on page 11.)
143
2
123
4
11 12
345678910
Label side up.
Disc tray
English
E-9
Notes
● After closing the disc tray by pressing OPEN/CLOSE, the
display shows the total number of tracks and the total recorded
time of the disc for a few seconds.
CDX-596
CDX-496, CDX-396
Example: To select track 25
Press +10 twice, then immediately press 5 once.
* If a track number higher than the highest track number on the
disc is selected, the last track on the disc will be played.
To pause play
Press .
To resume play, press again (or press ).
* on the front panel can also be used to stop play
temporarily or to resume play.
● Additionally, you can close the disc tray by pressing
( ), a numeric button or RANDOM, or by pressing the
front edge of the disc tray gently. If the tray is closed in one of
these ways, play will begin automatically; however, the display
will not show the total number of tracks nor the total recorded
time of the disc.
● CDX-596 only
If you load a CD-TEXT disc, the display also shows the disc
title after showing the total number of tracks and the total
recorded time of the disc.
+
I0
5
To turn off the power
Press POWER again.
* If you turn on the power again with a disc still on the tray, the
disc starts playing automatically from the first track.
To play directly from the desired track
Select a desired track by using the numeric buttons.
To select track number 10 or higher
Press +10 to select the first digit and then press a numeric
button (1–0) to select the second digit.
1
11
2
12
345678910
TOTAL
Gear wheel
Caution
When the disc tray is open, do not touch the inside gear
wheel. If you touch the gear wheel, your finger may be
caught in the closing tray and injured.
CDX-596
CDX-496, CDX-396
The selected track
number is displayed
To stop play
Press .
+
5
E-10
To advance rapidly
(Press and hold.)
To reverse rapidly
(Press and hold.)
To advance or reverse play rapidly (MANUAL SEARCH)
● The sound can be heard (although slightly garbled)
during manual search in either direction. This is
convenient for locating a precise position within a track, or
for reviewing the contents quickly.
● Manual search can also be performed while disc play is
paused, though no sound will be heard.
● When using SKIP/SEARCH on the front
panel:
Be careful not to release the button just after it is
pressed, otherwise the play is skipped to the beginning
of the next track or returned to the beginning of the
current track.
To play from the beginning of the next track
To play from the beginning of the current track
To play from the beginning of the preceding track
● These operations can also be performed when the unit is
paused or stopped.
● When using or on the remote control:
If (or ) is pressed and held, the track number
is continuously changed to higher numbers (or lower
numbers).
● When using SKIP/SEARCH on the front panel:
Be careful not to press and hold the button, otherwise
the selected track is played forward (or backward)
rapidly.
To skip to the beginning of the desired track (SKIP SEARCH)
(Press once.)
(Press once.)
(Press twice.)
English
E-11
Changing displays
CDX-596
You can select any of the four time displays (1 – 4) by pressing TEXT/TIME. When you play a CD-TEXT disc, the disc title,
artist name, and track name (5 – 7) are also displayed.
CDX-496 and CDX-396
You can select any of the four time displays by pressing TIME.
11
2
12
345678910
11
2
12
345678910
11
2
12
345678910
TITLE
CD-TEXT
11
2
12
345678910
ARTIST
CD-TEXT
11
2
12
345678910
TRACK
CD-TEXT
11
2
12
345678910
11
2
12
345678910
1Elapsed time of the current track
2 Remaining time of the current track
3 Total disc play time
4 Total remaining time on the disc 5 Disc title
6 Artist name
7 Track name
TOTAL
REMAIN
REMAIN
TOTAL
1 Elapsed time of the current track
2 Remaining time of the current track 3 Total disc play time
4 Total remaining time on the disc
TIME
TEXT/
TIME
Other useful functions
Notes
● The disc title, artist name, or track name may not be displayed with some CD-TEXT discs. In that case, “(NO ENTRY)” appears on the
display.
● When playing a CD-TEXT disc, “CD-TEXT” also lights up on displays 1 – 4.
E-12
Changing brightness of the display
CDX-596
You can change the brightness of the display (or turn off the illumination) by pressing DIMMER.
During play
Normal illumination
Dim
(off)*
* While the display illumination is off,
the AUTO DISPLAY OFF indicator
on the front panel lights up.
During a stop or a pause
Normal illumination
Dim
Dim*
* The AUTO DISPLAY OFF indicator lights up.
If a disc is played in this state, the display
illumination will be turned off.
CDX-496, CDX-396
If desired, you can change brightness of the display
in three degrees by pressing DIMMER.
Adjusting the level of signals output to the amplifier and the headphone listening level
CDX-596 and CDX-496 only
Normal illumination
Slightly dim
Dim
PHONES
DIMMER
DIMMER
OUTPUT LEVEL
+–
AUTO
DISPLAY OFF
You can adjust the level of signals output to the amplifier by
pressing
–
OUTPUT LEVEL
+.
Automatic spacing
If you record a disc onto tape with an insufficient time space
between tracks, the tape deck will not be able to perform
blank search operations on the tape correctly. To prevent
such a search mistake of the deck, press SPACE and light
up “SPACE” on the display before recording. Spaces of
about 4 seconds are inserted between the tracks.
“SPACE” disappears
from the display.
Note
When the automatic spacing function is in effect, the display
of the total time and of the total remaining time will include
each of the 4 second intervals placed between tracks.
To cancel the automatic spacing function
Press SPACE.
SPACE
SPACE
SPACE
PHONES
When you listen with headphones,
connect the headphones to the
PHONES jack and adjust the
volume by pressing
–
OUTPUT
LEVEL
+. At that time, note that
this adjustment will also vary the
signal level output to the amplifier.
English
E-13
The unit can play the tracks on a disc in a random sequence.
RANDOM-SEQUENCE PLAY
To perform random-sequence play
Press RANDOM.
To cancel random-sequence play
Press or RANDOM.
Notes
● This feature will not function while programming, or during
programmed play.
● If (SKIP/SEARCH ) is pressed during random-
sequence play, the next randomly programmed track will be
played. If ( SKIP/SEARCH) is pressed, play will
return to the beginning of the current track.
● This indication appears while the unit is mixing up
tracks.
● Total remaining time on the disc will not be displayed during
random-sequence play.
● CDX-596 and CDX-496 only
If the power is switched off during random-sequence play,
pressing POWER again to turn on the unit will automatically
restore random-sequence play.
You can play any desired track or the entire disc repeatedly by pressing REPEAT. The repeat play mode will change whenever
you press REPEAT.
REPEAT PLAY
CDX-596
(off)
CDX-496, CDX-396
(off)
SINGLE REPEAT (S)
A single track is played repeatedly.
* This also works for programmed play and random-sequence
play. (If repeat play is switched off, programmed play or
random-sequence play will be resumed.)
FULL REPEAT (F)
All tracks (the entire disc) are played repeatedly.
* During programmed play, all programmed tracks are played
repeatedly.
* During random-sequence play, all randomly sequenced tracks
are played repeatedly in the same order.
* CDX-596 and CDX-496 only
If the power is switched off during FULL REPEAT play,
pressing POWER again to turn on the unit will automatically
restore FULL REPEAT play.
RANDOM
RANDOM
or
REPEAT
REPEAT S
REPEAT F
SINGLE
REPEAT
FULL
REPEAT
E-14
You can enjoy listening to your favorite tracks in any desired order by programming tracks. As many as 40 tracks can be
programmed in sequence.
PROGRAM PLAY
1
Press to stop the unit.
2 Press PROG.
3 Program a desired track by
pressing the corresponding
numeric button.
Repeat this operation to program more tracks.
You can select the same track again.
4 When programming is finished,
press PROG.
5 Press to begin play.
Display information during programming
CDX-596
CDX-496, CDX-396
1
Shows the program number for the track to be
programmed next.
2 Shows the selected track number.
3 Shows only the numbers of programmed tracks.
4 Shows the total time of the tracks currently
programmed.
* If the total time becomes 100 minutes or more, the first
digit will not be displayed.
Notes
● If, during programming, TIME is pressed, the program number
display can be changed to display the total time of the
programmed tracks. To return to the previous display, press
TIME once again.
● / ( SKIP/SEARCH ) can be used during
playing, but only within the range of the programmed tracks.
● / ( SKIP/SEARCH ) can be used during
playing to search all tracks, including unprogrammed tracks.
PROG
6
PROGCLEAR
TAPE
32
1
65
4
98
7
INDEX
+
I0
0
3
2, 4
RANDOM
REPEAT
5
1
6
1
PROGRAM
PROGRAM
6
2
3
4
TOTAL
PROGRAM
2
3
TOTAL
PROGRAM
1
4
PROGRAM
TOTAL
PROGRAM
Blinks.
Blinks.
CDX-596
CDX-496, CDX-396
PROG
English
E-15
To stop program play
Press . The first programmed track number will be
displayed.
To resume play, press . Play will begin from the
beginning of the program.
To clear program data
There are several methods, as described below.
● Press or CLEAR while the unit is stopped.
● Open the disc tray.
● Switch off the power.
To check program data
1. If during program play, press .
2. Press PROG.
3. Each time (SKIP/SEARCH ) is pressed, the
track numbers and sequential order of the programmed
tracks can be checked one after another. The display of
the track number can be returned (sequentially in
reverse order) by pressing ( SKIP/SEARCH).
To correct program data
1. Follow the procedure described in “To check program
data”.
2. Display the track number to be corrected by pressing
/ ( SKIP/SEARCH ).
3. Press a numeric button to select a desired track to
replace the one displayed. The previously programmed
track will be cleared from the memory, and the new one
will be programmed.
4. Press PROG to complete the correction. To begin play
immediately after making the correction, press
instead of pressing PROG.
If the disc includes index numbers, play can be started from any desired index number.
INDEX SEARCH
1
Press a numeric button to select a track which has
index numbers.
2 Press INDEX.
3 Press a numeric button to select the desired index
number.
To cancel the index search function
Press INDEX.
Notes
● Not all discs have index numbers. In addition, among those
discs which have index numbers, not all discs necessarily have
more than one index number.
● The index system is a method for sub-dividing tracks into
smaller divisions for easier location of those parts. The liner
notes contained in the disc case usually tell that such index
numbers are included with the mark.
● If an index number is selected that is higher than any index
number on that disc, play will start from the last index point on
the disc.
● For some discs, play may begin slightly prior to the actual
designated index point.
● If the disc has no encoded index points, play will begin from
the beginning of the selected track.
● The index number can be designated only while “INDEX” is
illuminated.
INDEX
5
6
INDEX
11 12
5678910
CDX-596
CDX-496, CDX-396
E-16
46
60 90
54
The unit can program tracks on a disc for recording onto tape. By considering the tape’s total possible recording time, the unit
will automatically program tracks or help you program tracks so they will fit onto the tape with the least amount of unrecorded
space at each end of the tape.
TRACK PROGRAMMING FOR RECORDING TO TAPE
m Automatic tape-programming
The unit will automatically program tracks on a disc with their original order.
1 Press to stop the unit.
* The peak level search function of this unit is useful for
adjusting recording level on the tape deck. (Refer to page
20.)
2 If desired, you can automatically insert additional
time space between tracks by pressing SPACE to
light up “SPACE” on the display. (Refer to page 12.)
3 Press TAPE to show the tape’s total possible
recording time on the display.
You can select any of the four tape lengths by
pressing TAPE.
If desired, you can also enter the tape’s total possible
recording time manually.
Example: For a C-64 tape (32 minutes on each side),
press “6” and “4”.
+
4 Press REPEAT.
The unit automatically programs tracks for both side A
and side B considering the tape’s total time.
5 Begin recording on the tape deck, and then press
on this unit.
6 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording,
and then press or on this unit.
RANDOM
REPEAT
PEAK
SPACE
PROGCLEAR
TAPE
32
1
65
4
98
7
INDEX
+
I0
0
TEXT/
TIME
2
3
3
4
6
5, 6
1
SPACE
TAPE
REPEAT
6
4
SPACE
CDX-596
“TAPE 46” turns on.
CDX-496, CDX-396
“C-46” turns on.
(off)
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
Sivu latautuu ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
muilla kielillä
- polski: Yamaha CDX-396 Instrukcja obsługi
- Türkçe: Yamaha CDX-396 El kitabı
- English: Yamaha CDX-396 Owner's manual
- čeština: Yamaha CDX-396 Návod k obsluze
- svenska: Yamaha CDX-396 Bruksanvisning
- русский: Yamaha CDX-396 Инструкция по применению
- italiano: Yamaha CDX-396 Manuale del proprietario
- Deutsch: Yamaha CDX-396 Bedienungsanleitung
- português: Yamaha CDX-396 Manual do proprietário
- dansk: Yamaha CDX-396 Brugervejledning
- français: Yamaha CDX-396 Le manuel du propriétaire
- español: Yamaha CDX-396 El manual del propietario
- Nederlands: Yamaha CDX-396 de handleiding
- română: Yamaha CDX-396 Manualul proprietarului