Champion CHLED132 Ohjekirja

Kategoria
LCD TVs
Tyyppi
Ohjekirja
CHLED132
USER MANUAL
EN - English
SE - Svenska
DK - Danske
NO - Norsk
FI - Suomi
Read this Manual carefully before use
Introduction
Thank you very much for your purchase of our product of LED TV. It serves as a
normal color TV and PC monitor. To enjoy your TV to the full from the very
beginning, read this manual carefully and keep it handy for ready reference.
INSTALLATION
1. Locate the TV in a room where direct light does not strike the screen.
Totaldarknessorareectiononthepicturescreencancauseeyestrain.Soft
and indirect lighting is recommended for comfortable viewing.
2. Allow enough space between the receiver and the wall to permit ventilation.
3. Avoid excessively warm locations to prevent possible damage to the cabinet
or premature component failure.
4. This TV can be connected to 100-240V~ 50/60HZ.
5. Do not install the TV in a location near heat sources such as radiator, air-
ducts, direct sunlight, or in a place somewhere like close compartment and
close area. Do not cover the ventilation openings when using the TV.
6. The indicator light will last about 30 seconds to go out after cutting off the
electricity, during this period, you cannot repower it on until the indicator light
goes out, thanks a lot for your attention!
WARNING
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to avoid the risk
of electric shock, do not disassemble this equipment by
anyoneexceptaqualiedservicepersonnel.
EN
This symbol is intended to alert the user to the presence
of important operating and maintenance instructions in
the literature accompanying the equipment.
Class I structures of equipment should be connected to
the grid power output with a protective earth connection
on the socket.Power plug as a broken appliance, broken
installations should be easy to operate.
CAUTION
High voltages are used in the operation of this product.
Do not open the product’s casing. Refer servicing
toqualiedservicepersonnel.
Topreventreorelectricalshockhazard,donotexpose
the main unit to rain or moisture, do not place objects
lledwithliquids,suchasvases,ontheapparatus.
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
EN
EN
Avoid exposing the main unit to direct sunlight and other
sources of heat. Do not stand the television receiver
directly on other products which give off heat. E. g. video
cassetteplayers,Audioampliers.Donotblockthe
ventilation holes in the back cover. Ventilation is
essential to prevent failure of electrical component.
Do not squash power supply cord under the main unit or
other heavy objects.
Never stand on, lean on, push suddenly the product
or its stand. You should Pay special attention to
children.
Do not place the main unit on an unstable cart stand,
shelf or table. Serious injury to an individual, and
damage to the television, may result if it should fall.
When the product is not used for an extended period
of time, it is advisable to disconnect the AC power
cord from the AC outlet.
The LED panel used in this product is made of glass.
Therefore, it can break when the product is dropped
or applied with impact. Be careful not to be injured
by broken glass pieces in case the LED panel breaks.
EN
Optional Conguration as below:
Connect the USB to the USB jack on the set.
NOTE
- It is only 500 mA MAX of DC current output when you connect with USB jack
- To ensure the Mobile HD works well, you should use other power supply for the Mobile
HD. And do not use the USB jack in the same time.
- It supports Mobile HD by connecting with USB jack (must more than 2 GB). The partitions
of the Mobile HD can’t be more than 4 partitions. The max partition is 2TB. It supports
Main unit description
Control Panel Button Function
VOL+: Volume up.
VOL-: Volume down.
CH+: TV channel up.
CH- : TV channel down.
MENU : Press to select the main menu.
SOURCE : Select the input signal.
POWER : Turn the TV on or off.
TV Terminal Connections
1. EARPHONE output terminal
2. VGA input terminal
3. SCART input terminal
4. PC AUDIO input terminal
5. LNB IN
6. RF antenna
7. COAXIAL output terminal
8. HDMI input terminal
9. USB input terminal
10. Mini-AV input terminal
11. Mini-YP P input terminal
12. Cl slot
Remote control
:Press this button to Turn the TV on or off.
:Press this button to mute or restore sound.
NICAM/A2 :In the TV condition, press this key to select
the stereo mode.
ASPECT : Press to adjust picture ratio.
PMODE : Select picture mode.
SMODE : Select sound mode.
0-9 : Select and switch to a channel using 0 - 9.
-/--- : Switch the program digit.
: Switch back and front between the current
and previous channels.
DISPLAY : Display TV information.
FREEZE : Press to hold the picture.
: Start to record.
(The U disk will be formatted when in burning,
 pleasedonotstoreimportantlesintheUdisk.
AUTO : Adjust the picture automatically in pc mode.
RED, GREEN, YELLOW, BLUE
: Correspond to the different colored subjects.
SLEEP : Set the sleep timer.
SOURCE : Press to change signal source.
ENTER : Enter the selected option or execute the
selected operation.
NOTE : Press this button to display “channel list” in
TV source.
MENU : Press this button to enter the main menu for
various optional adjustable setting.
EXIT : Exit the OSD (On-screen display).
CH /H : Change the channel up and down.
VOL /VOL : Adjust the volume.
SUBTITLE : Open or close subtitle.
(Used for models with DTV function only)
T.SHIFT : Press the button to pause current DTV
program and start record background
(Used for models with DTV functions only)
HOLD : Freezeamulti-pagepassageonscreenin
Teletext mode.
(Used for European region only)
REVEAL : Press this button to reveal the hidden information
in Teletext page. Press again to hide the information.
EN
Press to play backward
(Used for models with MEDIA function only)
SIZE: Display the top, bottom or all of page to read easily in Teletext mode.
Press to play forward.
(Used for models with MEDIA function only)
INDEX: Press this button to go to the index page in Teletext.
Stop playing the Media.
(Used for models with MEDIA function only)
Skip to previous chapter
(Used for models with MEDIA function only)
S.PAGE: Carry out the function of SUBCODE
in the text while enter the text display mode.
Skip to next chapter
(Used for models with MEDIA function only)
TEXT: Press to enter the Teletext mode.
FAV: Switch between customer set ” Favorite List”
AUDIO: Press to select the DTV audio.
(Used for models with DTV function only)
DTV: Press to switch to DTV (Digital TV) mode.
EPG: Enter electronic program guide. (Used for models with
DTV function only)
TV/RADIO: Switch between TV and RADIO
(Used for models with DTV function only)
OSD basic adjustment
Installation Guide
IfthisisthersttimeyouareturningontheTVandtherearenoprogramsinthe
TV memory, the installation Guide menu will appear on the screen.
1. Press the button to select the language.
2. Press the button to select the local country you want to
3. Press the button to select energy mode.
Note: Searching for platform will take a long time, please be patient!
EN
DVB-S Channel
Press MENU button to display the main menu. Press button to select CHANNEL in the
main menu.
1. Auto Tuning
Press button to select “Auto Tuning”
Press button to select country and press the button to select Tune Type and Digital
Type.
Press “ENTER” button to start scanning. Press “MENU” button to skip or “EXIT” button to stop.
Note: Searching for platform will take a long time. Please be patient!
EN
Programme Edit
Press button to select ”Programme Edit” and press
the ”ENTER” button to enter.
a. DELETE
Press button to select the program and press
“RED” button once to delete the program.
b. SKIP
Press button to select the channel which you
want to skip and press the “BLUE” button to skip .
Press “BLUE” button again to cancel the setting.
c. MOVE
Press button to select the channel and press
the “YELLOW” button to move . Then press the
button to select the channel with which you want to
move.Press“YELLOW”buttonagaintoconrm.
Signal Information
Press button to select ”Signal Information” and press the ”ENTER” button to
enter.
CI Information
Press button to select ”CI Information”and press the ”ENTER” button to enter.
Logical Channel Number
Press button to select “Logical Channel Number” and press the ”ENTER” button to
on/off.
Dish Setup
Press button to select ”Dish Setup”and press the ”ENTER” button to enter.
EN
ATV/DVB-T Channel
Press MENU button to display the main menu. Press button to select CHANNEL in the
main menu
Auto Tuning
Press button to select “Auto Tuning”
Press button to select country and press the button to select Tune Type and Digital
Type.
Press “ENTER” button to start scanning. Press “MENU” button to skip or “EXIT” button to stop.
Note: Searching for platform will take a long time. Please be patient!
EN
ATV Manual Tuning
Press button to select “ATV Manual Tuning” and press the button to ATV Manual Tuning.
Press “MENU” button to return the previous menu. Press “EXIT” button to exit
the menu.
DTV Manual Tuning
Press button to select “DTV Manual Tuning” and press the button to start.
Press “MENU” button to return the previous menu.
Press “EXIT ” button to exit the menu.
Programme Edit
Press button to select “Programme Edit” and press the “ENTER” button to enter.
EN
a. DELETE
Press button to select the program and press “RED” button once to delete the program.
b. SKIP
Press button to select the channel which you want to skip and press the “BLUE”
button to skip . Press “BLUE” button again to cancel the setting.
c. MOVE
Press button to select the channel and press the “YELLOW” button to move . Then press
the button to select the channel with which you want to move. Press “YELLOW” button
againtoconrm.
Signal information (only use in DTV)
Press button to select “Signal information” and Press “MENU” button to return the
previous menu. Press “EXIT” button to exit the menu.
CI Information
Press button to select “CI Info” and press the “ENTER” button to check CI card
information.
Logical Channel Number
Press button to select “Logical Channel Number”and press the ”ENTER” button to
on/off.
Schedule List
Press button to select “Schedule List ” and Press “ENTER” button to enter submenu
PICTURE
You can select the type of picture, which best corresponds to your viewing. Press the “MENU”
button to enter the OSD menu. Then press button to select the “PICTURE” menu. Press
button to select “Picture Mode” and press the “ENTER” button to select.
EN
1. Press button to select “Contrast” and press the button to enter contrast
adjustment menu to adjust contrast.
2. Press button to select “Brightness” and press the button to enter brightness
adjustment menu to adjust brightness.
3. Press button to select “Colour” and press the button to enter colour
adjustment menu to adjust colour.
4. Press button to select “Sharpness” and press the button to enter sharpness
adjustment menu to adjust sharpness.
5. Press button to select “Tint’’ and press the button to enter Tint adjustment
menu to adjust Tint.
Note: The ’hue’ item is used in NTSC mode only.
6. Press button to select “Color Temp” and press the button to select mode
Normal/Cold/Warm.
7. Press button to select “Noise Reduction” and press the button to select.
8. Press button to select “HDMI Mode” and press the button to select.
SOUND
You can select the type of sound, which best corresponds to your listening.
Press the “MENU” button to enter the OSD menu. Then press button to select the
“SOUND” menu.
1. Press button to select “Sound Mode” and press the button to select mode.
2. Press button to select “Treble” and press the button to adjust.
3. Press button to select “Bass” and press the button to adjust.
4. Press button to select ”Balance” and press the ”ENTER” button to adjust.
5. Press button to select ”Auto Volume Level” and press the ”ENTER” button to adjust.
6. Press button to select ”SPDIF Mode” and press the ”ENTER” button to adjust.
7. Press button to select ”AD Switch” and press the ”ENTER” button to adjust.
TIME
Press the “MENU” button to enter the OSD menu. Then press button to select the “Time”
menu.
EN
1. Press button to select “Time Zone” and Press “ENTER” button to enter submenu .
Pressbuttontoselecttimezone”.
2. Press button to select “Sleep Timer” and Press “ENTER” button to enter
submenu. Press the button to adjust.
3. Press button to select “Auto Standby” and Press “ENTER” button to enter
submenu. Press the button to adjust.
4. Press button to select “OSD Timer” and Press “ENTER” button to enter submenu.
Press the button to adjust.
LOCK
Press the “MENU” button to enter the OSD menu. Then press button to select the
“Lock System” menu. The default password is “0000”.
Note: The administrator password is “8899’’.
1. Press button to select “System Lock’and then press button to select “On” or
“Off”
2. Press button to select “Set Password” and set your new password.
3. Press button to select “Channel Locks” and press the “GREEN” button to select
channel to lock .
4. Press button to select “Parental Guidance” and press the button to set.
5. Press button to select “Key Lock”, then press button to select “On” or “Off”, The key
board will be invalid if you set Lock Keypad “On”.
6. Press button to select “Hotel Mode” and press the button to enter the sub-menu to
set.
EN
SETUP
Press the “MENU” button to enter the OSD menu. Then press button to select the
“SETUP” menu.
1. Press button to select “Language” and press the button to select the OSD
language which you desire.
2. Press button to select “TT Language” and press the button to select the TT
language which you desire.
3. Press button to select “Audio Language” and press the button to enter the
Audio language adjustment menu to select the Audio language which you desire.
4. Press button to select “Subtitle Language” and press the button to enter the
subtitle language adjustment menu to select the subtitle language which you desire.
Note: This function is only used for DTV source.
5. Press button to select “Hearing Impaired” and press the button to select “On”
or “Off”.
6. Press button to select “Aspect Ratio” and press the button to select to select
aspect ratio: Auto,4:3,16:9,Zoom1, Zoom2
7. Press button to select “Blue Screen” and press the button to select “On” or
“Off”.
8. Press button to select “First Time Installation” and press “ENTER” button to enter.
9. Press button to select “Reset”, then press “ENTER” a dialogue. Press button
selecting “Yes” to restore all setting to default setting.
EN
10. Press button to select “Software Update” and press “ENTER” button to update
software using USB.
Note: It is only use for service
11. Press button to select “Environment”:Home Mode ,Shop Mode.
12. Press button to select “HDMI CEC”.
SCREEN
Press the “MENU” button to enter the OSD menu. Then press button to select the
“SCREEN” menu.(Only available in PC mode)
1. Press button to select “Auto Adjust” and press the “ENTER” button to adjust.
2. Press button to select “H-Offset” and press the button to adjust.
3. Press button to select “V-Offset” and press the button to adjust.
4.Pressbuttontoselect“Size”andpressthe“ENTER”buttontoadjust.
5. Press button to select “Phase” and press the “ENTER” button to adjust.
6. Press button to select “Position Reset” and press the “ENTER” button to adjust.
DTV Features
Favorite List
When the source is selected as DTV, users can enter Favorite List by pressing “FAV” button.
The “Favorite List” window is illustrated as follows:
You can press the button to select the favorite list number
EN
Program Information
When the source is selected as DTV, you can press “display” button to display the channel’s
information. The program information window is illustrated as follows:
Audio
When the source is selected as DTV, users can enter the Setup menu to enter the “Audio
Language” menu . The “audio language” window is illustrated, and press button to select the
“Audio Language” menu.
Subtitle
When the source is selected as DTV, users can go to the menu to set.
Note: The pictures in regard to function
are provided for reference purposes
only.
USB Features
Press the “SOURCE” button to change to the “MEDIA” source.
EN
Photo
1. Press the button enter the “PHOTO” option, and press “ENTER” button to enter
2. Press button to select drive disk you want to watch, then press enter button to enter.
3. Press the “EXIT” button to back to the previous menu.
Music
1. Press button to select MUSIC in the main menu, then press “ENTER” button to enter
2. Press button to select drive disk you want to watch, then press enter button to enter
3. Press the “exit” button to back to the previous menu.
Movie
1. Press button to select “MOVIE” in the main menu, then press “ENTER” button to enter
2. Press button to select drive disk you want to watch, then press enter button to enter
3. Press the “exit” button to back to the previous menu.
EN
Text
1. Press button to select “TEXT” in the main menu, then press “ENTER” button to enter
2. Press button to select drive disk you want to watch, then press enter button to enter
3. Press the “exit” button to back to the previous menu.
EN
Electronic Program Guide (EPG)
Electronic Program Guide (EPG) provides program information which will be broadcasted
now or in the future. The system will display EPG window by pressing EPG button. DATE and
TIME information is displayed on the right of the window. The left side shows all channels. The
right side shows the programs in the channel. The selected program is also displayed on the top
of the screen.
1. Press the button to select the program. You can press ”RED” button to enter record
mode. Press ”GREEN” button to display the programs detail. Press ”YELLOW” button to check
details at PVR´s Schedule List instroduction. Press ”BLUE” button to enter reminder setting.
2. Press the button to select and press the button to select the channel number to
see the current channel´s program forecast.
Note: The U disk will be formated when in burning, please do not store important les in the U disk.
PVR Operation
In DTV source, press the ”MENU” button to enter the OSD menu. Then press button to
select the ”Setup” menu.
1. Press button to select ”PVR File System” and press the ”ENTER” button to enter.
2. Press button to select ”Check PVR File System”, then press ”ENTER” button to enter.
Note:
1. The U disk will be formated when in format, please do not store important les in the U disk.
2. Press the ” ” button for the rst time to start recording, for the second time, the sign of recorder will be
slimmed down, but it´s still under recording.
Specication
RGB INPUT
Mode Resolution Horizontal Frequency
(KHz)
Vertical Frequency
(HZ)
DOS 720x400 31.5 70
VGA 640x480 31.5 60
SVGA 800x600 37.9 60
XGA 1024x768 48.4 60
XVGA 1366x768 47.7 60
EN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106

Champion CHLED132 Ohjekirja

Kategoria
LCD TVs
Tyyppi
Ohjekirja