Simplicity 54E177-0009-J1 Ohjekirja

Tyyppi
Ohjekirja
Operator's Manual
Betjeningsvejledning
Bedienungsanleitung
Εγχειρίδιο χρήσ
Manual del operador
Käyttäjän käsikirja
Manuel d'utilisation
Manuale dell’Operatore
Gebruiksaanwijzing
Brukerhåndbok
Manual do Operador
Instruktionsbok
Models:54E000,540000,61E000,610000,61G200,
61G300
© Briggs & Stratton. All rights reserved. 80102667
Revision A
Not for
Reproduction
1
2
3
4
5
6
7
8
9
2 vanguardpower.com
Not for
Reproduction
10
11
12
13
14
15
16
17
18
3
Not for
Reproduction
General Information
This manual contains safety information so that you will know the hazards and risks
related to this engine and how to prevent them. It also contains instructions for the
correct use and maintenance of the engine. Because Briggs & Stratton does not know
what equipment this engine will power, it is important that you read, understand, and
obey these instructions. Save these original instructions for future reference.
NOTE:The figures and illustrations in this manual are for reference only and can be
different from your model. If you need help, contact an Authorized Service Dealer.
For replacement parts or technical help, record the date of purchase, engine model,
type, trim, and the engine serial number. These numbers are located on your engine.
Refer to the Features and Controls section.
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
European Office Contact Information
For questions related to European emissions, contact our European office at:
Max-Born-Straße 2, 68519 Viernheim, Germany.
European Union (EU) Stage V (5): Carbon
Dioxide (CO2) Values
Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values
of Briggs & Stratton EU Type-Approval Certificate engines.
Recycling Information
Recycle all cartons, boxes, used oil, and batteries as
specified by government regulations.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol identifies safety information about hazards that could
result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to
indicate the likelihood and the potential severity of injury. In addition, a hazard symbol
is used to represent the type of hazard.
DANGER indicates a hazard which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not avoided, could result in minor or moderate
injury.
NOTICE indicates information considered important but not hazard-related.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire Hazard Explosion Hazard
Shock Hazard Toxic Fume Hazard
Hot Surface Hazard Noise Hazard - Ear
protection recommended
for extended use.
Thrown Object Hazard -
Wear eye protection.
Explosion Hazard
Frostbite Hazard Kickback Hazard
Amputation Hazard -
Moving Parts
Chemical Hazard
Thermal Heat Hazard Corrosive Hazard
Safety Messages
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products, see
www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs
& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result
in serious injury or death.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
Fill the fuel tank outdoors or in an area that has good airflow.
Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
If fuel spills, wait until it dries before you start the engine.
When you start the engine
Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are
correctly installed.
Do not crank the engine with the spark plug removed.
If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
When you operate the equipment
Do not tilt the engine or the equipment at an angle which causes fuel to spill.
Do not choke the carburetor (if equipped) to stop the engine.
Do not start or operate the engine with the air cleaner (if equipped) or the air
filter (if equipped) removed.
When you do maintenance
If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occurand could result a fire or an explosion.
During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,
if mounted on the engine, is empty and that the spark plug side is up. If the fuel
tank is not empty, leakage can occurand could result a fire or an explosion.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
Do not change the governor spring, links or other parts to increase engine
speed.
Do not hit the flywheel with a hammer or hard object. This could result in failure
of the flywheel during operation.
Replacement parts must be of the same design and installed in the same
position as the original parts. Other parts could result in damage or an injury.
4 vanguardpower.com
Not for
Reproduction
When you move the location of equipment
Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the
CLOSED position.
When fuel or equipment is in storage with fuel in the fuel tank
Because pilot lights or other ignition sources can cause explosions, keep fuel or
equipment away from furnaces, stoves, water heaters or other appliances that
have pilot lights.
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Engine start-up causes spark that could result in a fire or explosion.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and windows
for ventilation. After the operation of this product, carbon monoxide can quickly
collect in these spaces and stay for hours.
ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
Before you start the engine, disconnect or remove all external equipment and
engine loads.
Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
WARNING
Rotating parts can entangle hands, feet, hair, clothing, or accessories and result
in traumatic amputation or laceration.
Operate equipment with the guards correctly installed.
Keep hands and feet away from rotating parts.
Remove jewelry and make sure that long hair is away from all rotating parts.
Do not wear loose clothes or items that could become caught.
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
WARNING
Accidental engine spark can cause an electric shock or fire and could result in
entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect the battery wire from the negative battery terminal (only engines with
electric start.)
Use only the correct tools.
When you check for spark:
Use an approved spark plug tester.
Do not check for spark with the spark plug removed.
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
If you smell gas
Do not start the engine.
Do not switch on electrical switches.
Do not use a phone in the vicinity.
Evacuate the area.
Contact the gas supplier or the fire department.
Features and Controls
Engine Controls
Compare the callout letters in Figures 1, 2, 3, and 4 to the engine controls in the list that
follows:
A. Engine Identification Numbers Model - Type - Code
B. Spark Plug
C. Cyclonic Air Cleaner
D. Low Profile Air Cleaner
E. Dipstick
F. Oil Fill
G. Oil Filter
H. Oil Drain Plug
I. Oil Pressure Sensor
J. Finger Guard
K. Electric Starter
L. Starter Solenoid
M. Regulator / Rectifier
N. Carburetor - Carburetor Models
O. Oil Cooler (if equipped)
P. Muffler (if equipped)
Q. Fuel Pump
R.
Starter Switch
1
S.
Throttle Control
1
T.
ChokeControl(Carburetor Models
1
)
U. Fuel Filter
V. Tachometer (if equipped)
1
Some engines and equipment have remote controls. See the equipment manual for the
location and operation of remote controls.
Engine Control Symbols and Meanings
Engine Speed - FAST Engine Speed - SLOW
Engine Speed - STOP ON - OFF
5
Not for
Reproduction
Engine Start
Choke CLOSED
Engine Start
Choke OPEN
Fuel Cap
Fuel Shut-off OPEN
Fuel Shut-off CLOSED
Fuel Level - Maximum
Do Not Overfill
Operation
Oil Recommendations
Oil Capacity: See the Specifications section.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or
dealers could have added oil to the engine. Before you start the engine for the first time,
make sure that the oil is at the correct level. Add oil as specified by the instructions in
this manual. If you start the engine without oil, damage will occur and the engine will not
be repaired under warranty.
We recommend the use of Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Use the chart to select the best viscosity for the outdoor temperature range expected.
Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For
equipment operated in hot temperatures, Vanguard
®
15W-50 Synthetic oil gives the best
protection.
A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
E
Vanguard
®
Synthetic 15W-50
Check and Add Oil
Before you check or add oil
Make sure the engine is level.
Clean the oil fill area of debris.
Refer to the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or
dealers could have added oil to the engine. Before you start the engine for the first time,
make sure that the oil is at the correct level. Add oil as specified by the instructions in
this manual. If you start the engine without oil, damage will occur and the engine will not
be repaired under warranty.
1. Remove the dipstick (A, Figure 5) and clean with a cloth.
2. Install and tighten the dipstick (A, Figure 5).
3. Remove the dipstick and check the oil level. Make sure that the oil level is at the
top of the full indicator (B, Figure 5) on the dipstick.
4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not add
too much oil. After you add oil, wait one minute and check the oil level again. Make
sure that the oil level is correct.
5. Install and tighten the dipstick (A, Figure 5).
Low Oil Protection System (if equipped)
A low oil sensor is installed on some engines. If the oil is low, the sensor will display a
warning light or stop the engine. Stop the engine and follow these steps before you start
the engine.
Make sure the engine is level.
Do an oil check. Refer to the Check Oil Level section.
If the oil level is low, add the correct amount of oil. Start the engine and make
sure the warning light (if equipped) does not come on.
If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to have the oil problem corrected.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
Gasoline with up to 10% ethanol (gasohol) is permitted.
NOTICE
Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or
change the engine to operate on alternate fuels. Use of unapproved fuels could result in
damage to engine components, which will not be repaired under the warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. Refer
to the Storage section. All fuel is not the same. If start or performance problems occur,
change fuel providers or brands. This engine is certified to operate on gasoline. The
emissions control system for carbureted engines is EM (Engine Modifications). The
emissions control systems for engines with electronic fuel injection are ECM (Engine
Control Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is permitted.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
When you add fuel
Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)
minutes to make sure that the engine is cool.
Fill the fuel tank outdoors or in an area that has good airflow.
Do not put too much fuel in the tank. For expansion of the fuel, do not fill above
the bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
If fuel spills, wait until it dries before you start the engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 6) with fuel. Because fuel will expand, do not fill above
the bottom of the fuel tank neck (B).
3. Install the fuel cap.
Start and Stop Engine
Start Engine
WARNING
Fast retraction of the starter cord (kickback) will pull your hand and arm to the
engine faster than you can let go.Broken bones, fractures, bruises or sprains
could result.
To prevent kickback when you start the engine, pull the starter cord slowly until
resistance is felt and then pull quickly.
Before you start the engine, disconnect or remove all external equipment and
engine loads.
Make sure that direct-coupled equipment components, such as, but not limited
to, blades, impellers, pulleys, and sprockets, are correctly attached.
6 vanguardpower.com
Not for
Reproduction
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result
in burns or death.
When you start the engine
Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped)
are correctly installed.
Do not crank the engine with the spark plug removed.
If the engine is flooded, set the choke (if equipped) to the OPEN or RUN
position. Move the throttle (if equipped) to the FAST position and crank until the
engine starts.
If there is natural or LP gas leakage in the area, do not start the engine.
Because vapors are flammable, do not use pressurized starter fluids.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. Although you do not smell exhaust
fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel
sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY.
See a doctor. You may have carbon monoxide poisoning.
Carbon monoxide gas can collect in occupied spaces. To reduce the risk of
carbon monoxide gas, ONLY operate this product outdoors and far away from
windows, doors and vents.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up as specified by the manufacturer's instructions.
Smoke alarms cannot sense carbon monoxide gas.
DO NOT operate this product in homes, garages, basements, crawlspaces,
sheds, or other closed spaces, even if you use fans or open doors and
windows for ventilation. After the operation of this product, carbon monoxide
can quickly collect in these spaces and stay for hours.
ALWAYS put this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers could have added oil to the engine. Before you start the engine for the
first time, make sure that the oil is at the correct level. Add oil as specified by the
instructions in this manual. If you start the engine without oil, damage will occur and the
engine will not be repaired under warranty.
Types of Starting Systems
Before you start the engine, you must know the type of starting system on your engine.
Your engine will have one of these types.
Electronic Fuel Injection (EFI) System: An EFI system does not have a
choke or a primer.
Choke System: This type of system has a choke to be used in cool
temperatures. Some models will have a separate choke control while others
will have a combination choke and throttle choke. It does not have a primer.
NOTE:Your equipment could have remote controls. Refer to the equipment manual for
location and operation of remote controls.
Electronic Fuel Injection (EFI) System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate
the engine in the FAST position.
5. Turn the electric start switch (D, Figure 7) to the ON or START position.
NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).
Wait one minute between start cycles.
If the engine does not start after 3or 4 times, contact your local dealer or goto
vanguardpower.com or call 1-800-999-9333.
Choke System
1. Check the engine oil. See the Check Oil Level section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.
4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate
the engine in the FAST position.
5. Move the choke control (C, Figure 7), or the combination choke and throttle (B,C) to
the CLOSED position.
NOTE:To start the engine with a dry fuel system, additional cranking time in the choke
position will be required. This will give the fuel pump time to prime the fuel system.
6. Turn the key switch (D, Figure 7) to the ON or START position.
7. If the engine starts but will not continue to operate, move the choke control (C,
Figure 7) to the OPEN position to start the engine.
NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).
Wait one minute between start cycles.
8. As the engine warms, move the choke control (C, Figure 7) to the OPEN position.
If the engine does not start after 3or 4 times, contact your local dealer or goto
vanguardpower.com or call 1-800-999-9333.
Stop the Engine
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Do not choke the carburetor (if equipped) to stop the engine.
1. With the throttle control in the SLOW position, turn the electric start switch (D,
Figure 7) to the OFF position. Remove the key and keep it in a safe place out of the
reach of children.
2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the
CLOSED position.
Maintenance
Maintenance Information
WARNING
During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if
mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not
empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted
in a different direction, it will not easily start because of oil or fuel contamination of the air
filter or the spark plug.
We recommend that you see a Briggs & Stratton Authorized Service Dealer for all
maintenance and servicing of the engine and engine parts.
NOTICE
All the components used to build this engine must remain in place for correct operation.
WARNING
Accidental engine spark can cause an electric shock or fire and could result in
entanglement, traumatic amputation or laceration.
Before you make adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect the battery wire from the negative battery terminal (only engines with
electric start.)
Use only the correct tools.
When you check for spark:
Use an approved spark plug tester.
Do not check for spark with the spark plug removed.
Emissions Control Service
For maintenance, replacement, or repair of emissions control devices and
systems, contact a qualified off-road engine repair establishment or service
technician. However, for "no charge" emissions control service, the work must be done
by a factory authorized dealer. Refer to the Emissions Control Statements.
Maintenance Schedule
Intervals of 8 Hours or Daily
Check the engine oil level.
Clean the area around the muffler and controls.
Intervals of 100 Hours or Annually
7
Not for
Reproduction
Clean or replace the air filter
1 2
.
Change the engine oil and filter.
Replace the oil filter (if equipped).
Replace the spark plugs.
Check the muffler and spark arrester.
Service the exhaust system.
Intervals of 250 Hours or Annually
Check the valve clearance. Adjust if necessary.
Intervals of 400 Hours or Annually
Change the air filter
2
.
Replace the fuel filter.
Service the air cooling system
1
.
Clean the oil cooler fins
1
.
Intervals of 600 Hours
Replace the safety filter, if equipped.
1
In dusty conditions or when airborne debris is present, clean more frequently.
2
Every third air filter change, replace the inner safety filter (if equipped.
Electronic Fuel Injection (EFI) System
The EFI System monitors engine temperature, engine speed, and battery voltage for
engine start-up and warm-up. There are no adjustments on the system. If start-up or
operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.
NOTICEMake sure to obey the steps that follow or damage to the EFI system could
occur.
DO NOT start the engine if the battery cables are loose.
Turn the key to the OFF position before you disconnect, remove, and / or install
the battery.
DO NOT use a battery charger to start the engine.
DO NOT disconnect the battery cables during engine operation.
When you disconnect the battery cables, first connect the positive (+) cable, and
then connect the negative (-) cable to the battery.
When you charge the battery, turn the ignition switch to the OFF position,and
disconnect the negative (-) battery cable from the battery.
DO NOT spray water directly on the Electronic Control Module.
Carburetor and Engine Speed
Do not make adjustments to the carburetor or engine speed. The carburetor was set at
the factory to operate satisfactorily under most conditions. Do not change the governor
spring, linkages, or other parts to adjust the engine speed. If any adjustments are
required contact a Briggs & Stratton Authorized Service Dealer for service.
NOTICE
The equipment manufacturer specifies the maximum speed for the engine as installed
on the equipment. Do not exceed this speed. If you are not sure what the equipment
maximum speed is, or what the engine speed is set to from the factory, contact a Briggs
& Stratton Authorized Service Dealer for assistance. For safe and correct operation
of the equipment, the engine speed should only be adjusted by a qualified service
technician.
Servicing the Spark Plug
Check the spark plug gap (A, Figure 8) with a wire gauge (B). If necessary, set the
spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque
specifications, refer to the Specifications section.
NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug
to decrease ignition signals.If a resistor spark plug was installed by the equipment
manufacturer, use the same type for replacement.
Servicing theExhaust System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible materials, such as leaves, grass and brush, can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
It is a violation of California Public Resource Code, Section 4442, to use or operate the
engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust
system is equipped with a spark arrester, as defined in section 4442, maintained in
effective working order. Other states or federal jurisdictions may have similar laws;
reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment
manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust
system installed on this engine.
Remove debris from the muffler and cylinder area. Examine the muffler for cracks,
corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and
examine for damage or carbon blockage. If damage is found, install the replacement
parts before you operate the equipment.
WARNING
Replacement parts must be of the same design and installed in the same position as the
original parts. Other parts could result in damage or an injury.
Change Engine Oil
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not
empty, fuel leakage can occur and cause a fire or an explosion.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Used oil is a hazardous waste product and must be discarded of correctly. Do not
discard with household waste. Contact your local authorities, service center, or dealer
for safe disposal or recycling facilities.
Remove Oil
1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 9), and
keep it away from the spark plug(s)(E).
2. Remove the dipstick (A, Figure 10).
3. Remove the oil drain plug (F, Figure 11). Drain the oil into an approved container.
4. Install and tighten the oil drain plug(F, Figure 11).
Change Oil Filter, if equipped
1. Drain the oil from the engine. Refer to the Remove Oil section.
2. Remove the oil filter (H, Figure 12) anddiscard correctly.
3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.
4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten
the oil filter 1/2 to 3/4 turns.
5. Add oil. Refer to the Add Oil section.
6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.
7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure
5) on the dipstick.
Add Oil
Make sure the engine is level.
Clean the oil fill area of all debris.
Refer to the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 10). Remove oil from the dipstick with a clean cloth.
2. Slowly add oil into the engine oil fill (C, Figure 10). Do not overfill. Wait one
minute and then check the oil level.
3. Install and tighten the dipstick (A, Figure 10).
4. Remove the dipstick and check the oil level. The correct oil level is at the top of the
full indicator (B, Figure 10) on the dipstick.
5. Install and tighten the dipstick (A, Figure 10).
6. Connect the spark plug wire(s) (D, Figure 9) to the spark plug(s) (E).
Servicing the Air Filter
WARNING
Fuel vapors are flammable and explosive. Fire or explosion could result in burns
or death.
Do notstart and operate the engine with the air cleaner assembly (if equipped)
or the air filter (if equipped) removed.
8 vanguardpower.com
Not for
Reproduction
NOTICE
Do not use pressurized air or solvents to clean the filter. Pressurized air could result in
damage to the filter and solvents will dissolve the filter.
See the Maintenance Schedule for service requirements.
Different models will use a foam or a paper filter. Some models could also have an
optional pre-cleaner that can be washed and used again. Compare the illustrations in
this manual with the type installed on your engine and service as follows.
Cyclonic Air Filter
1. Open the fastener(s) (A, Figure 13) and remove the cover (B).
2. Remove the air filter (C, Figure 13).
3. To loosen debris, lightly tap the air filter on a hard surface. If the air filter is dirty,
replace it with a new air filter.
4. To remove the safety filter (D, Figure 13), if equipped, carefully pull it away from the
air cleaner body (E). Make sure that dirt or debris does not go into the engine.
5. Install the new safety filter (D, Figure 13) in the air cleaner body (E).
6. Install the air filter (C, Figure 13) above the safety filter (D).
7. Install the cover (B, Figure 13) and close the fastener(s) (A).
Low Profile Air Filter
1. Remove the fastener(s) (A, Figure 14).
2. Remove the cover (B, Figure 14).
3. Remove the fastener(s) (C, Figure 14) and retainer (D).
4. Remove the air filter (E, Figure 14).
5. Remove the pre-cleaner (F, Figure 14), if equipped, from the air filter (E).
6. To loosen debris, lightly tap the air filter (E, Figure 14) on a hard surface. If the air
filter is dirty, replace with a new air filter.
7. Clean the pre-cleaner (F, Figure 14), if equipped, in liquid detergent and water.
Make sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.
8. Assemble the dry pre-cleaner (F, Figure 14), if equipped, to the air filter (E).
9. Install the air filter (E, Figure 14) with the retainer (D) and fastener(s) (C).
10. Install the cover (B, Figure 14) with the fastener(s) (A). Make sure the fastener(s) is
tight.
Servicing the Cooling System
WARNING
During operation, the engine and muffler become hot. If you touch a hot engine,
thermal burns can occur.
Combustible debris, such as leaves, grass, and brush can catch fire.
Before you touch the engine or muffler, stop the engine and wait two (2)
minutes. Make sure that the engine and muffler are safe to touch.
Remove debris from the muffler and engine.
NOTICE
Do not use water to clean the engine. Water could cause contamination of the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to
become too hot and result in unsatisfactory performance and decreased engine life.
1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 15).
2. Keep linkage, springs, and controls (B, Figures 15, 16) clean.
3. Keep the area around and behind the muffler (C, Figures 15, 16) free of
combustible debris.
4. Make sure the oil cooler fins (D, Figure 15) are free of dirt and debris.
5. Loosen the fastener(s) (E, Figures 15, 16) and remove the debris access panels
(F). Remove grass and debris that has collected on the cylinders.
6. Install the debris access panels (F, Figures 15, 16) and attach with fastener(s) (E).
After a period of time, debris can collect in the cylinder cooling fins and cause the engine
to overheat. This debris cannot be removed without partial disassembly of the engine.
As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized
Service Dealer inspect and clean the air cooling system.
Servicing the Fuel System
WARNING
Fuel and its vapors are flammable and explosive. Fire or explosion could result in
burns or death.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks
or leaks. Replace damaged parts.
Before you clean or replace the fuel filter, drain the fuel tank or close the fuel
shut-off valve.
If fuel spills, wait until it dries before you start the engine.
Replacement parts must be of the same design and installed in the same
position as the original parts. Other parts could result in damage or an injury.
Fuel Filter, if equipped
1. Before you clean or replace the fuel filter (A, Figure 17), drain the fuel tank or close
the fuel shut-off valve. If the fuel tank is not drained, fuel leakage could occur and
cause a fire or explosion.
2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then move the clamps
away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.
3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.
4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.
5. Attach the fuel lines (D, Figure 17) with clamps (C).
Storage
Fuel System
Refer to Figure: 18.
Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 18) with
fuel. For fuel expansion, do not fill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. Each
time you fill the container with fuel, addto the fuel as specified by the manufacturer’s
instructions. This keeps fuel fresh and decreases fuel-related problems or contamination
in the fuel system.
It is not necessary to drain fuel from the engine whenis added as instructed. Before
storage, turn the engine ON for 2 minutes to move the fuel and stabilizer through the fuel
system.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained
into an approved container. Operate the engine until it stops from lack of fuel. The use of
a fuel stabilizer in the storage container is recommended to keep fuel fresh.
Engine Oil
While the engine is still warm, change the engine oil. Refer to Change the Engine Oil
section.
Troubleshooting
Assistance
For assistance, contact your local dealer or go to vanguardpower.com or call
1-800-999-9333 (in USA).
Specifications
Specifications and Service Parts
Models: 540000 , 54E000
Displacement 54.68 ci (896 cc)
Bore 3.366 in ( 85,5 mm)
Stroke 3.071 in (78,0 mm)
Oil Capacity 78 - 80 oz (2,3 - 2,4 L)
Spark Plug Gap .030 in (,76 mm)
Spark Plug Torque 180 lb-in (20 Nm)
Armature Air Gap .005 - .008 in (,13 - ,20 mm)
Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)
Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)
Models: 610000, 61E000, 61G200, 61G300
Displacement 60.60 ci (993 cc)
Bore 3.366 in ( 85,5 mm)
9
Not for
Reproduction
Models: 610000, 61E000, 61G200, 61G300
Stroke 3.406 in (86,5 mm)
Oil Capacity 78 - 80 oz (2,3 - 2,4 L)
Spark Plug Gap .030 in (,76 mm)
Spark Plug Torque 180 lb-in (20 Nm)
Armature Air Gap .005 - .008 in (,13 - ,20 mm)
Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)
Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)
Service Parts - Models: 540000, 54E000,
610000, 61E000, 61G200, 61G300
Service Part Part Number
Cyclonic Air Filter (Figure 13) 841497
Cyclonic Safety Filter (Figure 13) 821136
Air Filter, Low Profile (Figure 14) 692519
Pre-cleaner, Low Profile (Figure 14) 692520
Oil - SAE 30 100028
Oil Filter 842921
Fuel Filter 691035
Resistor Spark Plug 491055
Long Life Platinum Spark Plug 5066
Spark Plug Wrench 19374
Spark Tester 19368
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily
at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted
operating limits on slopes.
Power Ratings
The gross power rating for individual gasoline engine models is labeled in accordance
with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque
Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM
for all others; horsepower values are derived at 3600 RPM. The gross power curves
can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with
exhaust and air cleaner installed whereas gross power values are collected without
these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the
variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
Warranty
Briggs & Stratton Engine Warranty
Effective January 2019
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this
warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
The purchaser must contact the Authorized Service Dealer, and then make the product
available to the Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law. Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state and country to country
4
.
Standard Warranty Terms
1, 2, 3
Vanguard®; Commercial Series
3
Consumer Use - 36 months
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
1
These are our standard warranty terms, but occasionally there may be additional
warranty coverage that was not determined at time of publication. For a listing
of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or
contact your Briggs & Stratton Authorized Service Dealer.
2
There is no warranty for engines on equipment used for prime power in place
of a utility; standby generators used for commercial purposes, utility vehicles
exceeding 25 MPH, or engines used in competitive racing or on commercial or
rental tracks.
3
Vanguard installed on standby generators: 24 months consumer use, no
warranty commercial use. Commercial Series with manufacturing date before July
2017: 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by
emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or
commercial consumer. "Consumer use" means personal residential household use by a
retail consumer. "Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial
use, it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial
purchase date at the time warranty service is requested, the manufacturing date
of the product will be used to determine the warranty period. Product registration
is not required to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than
10%, or the use of alternative fuels such as liquefied petroleum or natural gas on
engines not originally designed/manufactured by Briggs & Stratton to operate on
such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
10 vanguardpower.com
Not for
Reproduction
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. F)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2020-2022 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards. B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.
If any emissions-related part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual. B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations adopted by the Air Resources Board; that
it is free from defects in material and workmanship that could cause the failure
of a warranted part; and that it is identical in allmaterial respects to the engine
described in the manufacturer’s application for certification. The warranty period
begins on the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled for replacement as required
maintenance in the Operators’s Manual supplied, is warranted for the period
of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired
or replaced by B&S at no charge to the owner. Any such part repaired or
replaced under warranty will be warranted for the remainder of the period
prior to the first scheduled replacement point for the part.
Add-on or modified parts that are not exempted by the Air Resources Board
may not be used. The use of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty claim. The manufacturer
will not be liable to warrant failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
The Emissions Durability Period describes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, the Emissions Durability Period of an engine with an intermediate rating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
11
Not for
Reproduction
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80099153(Revision A)
Briggs & Stratton Emissions Warranty
U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -
Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Jx)
The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust
emissions control system warranty on your Model Year 2020-2022 engine. In the U.S,
new small off-road engines and large spark ignited engines less than or equal to 1.0
liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S
must warrant the emissions control system on your engine for the periods of time listed
below provided there has been no abuse, neglect, or improper maintenance of your
engine leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years. If
any emissions-related parts on your engine is defective, the part will be repaired of
replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the performance of the required
maintenance listed in your Operator’s Manual. B&S recommends that you
retain all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or your failure to ensure the
performance of all scheduled maintenance.
As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect,
improper maintenance, or unapproved modifications.
You are responsible for presenting your engine to a B&S distribution center,
or service center, as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days. If you
have a question regarding your warranty rights and responsibilities, you should
contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the period listed in the respective engine or product warranty
statement, whichever is greater. B&S warrants to the original purchaser and each
subsequent purchaser that the engine is designed, built, and equipped so as to
conform with all applicable regulations under Section 213 of the Clean Air Act that
is free from defects in material and workmanshipthat could cause the failure of a
warranted part; and that is identical in all material respects to the engine described
in the manufacturer’s application for certification. The warranty period begins on
the date the engine or equipment is delivered to an ultimate purchaser.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to
the owner. Any such part repaired or replaced under the warranty will be
warranted for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled for replacement as required
maintenance in the Operator's Manual supplied, is warranted for the period of
time prior to the first scheduled replacement point for that part. If the part fails
prior to the first scheduled replacement, the part will be repaired or replaced
by B&S at no charge to the owner. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first
scheduled replacement point for the part.
Add-on or modified parts that are not exempted by the U.S. EPA may not be
used. The use of any non-exempted add-on or modified parts by the owner
will be grounds for disallowing a warranty claim. The manufacturer will not
be liable to warrant failures of warranted parts caused by the use of a non-
exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of
operating hours for which the engine has been shown to meet Federal emissions
requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80099149 (Revision A)
12 vanguardpower.com
Not for
Reproduction
Generel information
Denne vejledning indeholder sikkerhedsoplysninger, der skal gøre dig opmærksom
på farer og risici i forbindelse med denne motor, og hvordan du forhindrer dem. Den
indeholder også instruktioner til korrekt brug og vedligeholdelse af motoren. Eftersom
Briggs & Stratton ikke ved, hvilket udstyr denne motor skal drive, er det vigtigt, at
du læser, forstår og følger disse instruktioner. Gem disse originale anvisninger til
fremtidig brug.
BEMÆRK:Figurerne og illustrationerne i denne vejledning er udelukkende til
referencebrug og kan være anderledes end din model. Hvis du har brug for hjælp,
kontakt en autoriseret serviceforhandler.
For at kunne få reservedele eller teknisk assistance skal du registrere købsdatoen samt
motorens model-, type-, trim- og serienummer. Disse numre er placeret på din motor. Se
afsnittet Funktioner og betjeningsanordninger.
Købsdato
Motormodel- Type- Trim
Motorserienummer
Kontaktoplysninger for europæisk kontor
For spørgsmål vedrørende europæisk emission bedes du kontakte vores europæiske
kontor på:
Max-Born-Straße 2, 68519 Viernheim, Tyskland.
Europæiske Union (EU) Trin V (5):
Kuldioxid-værdier (CO2)
Indtast CO2 i søgevinduet på BriggsandStratton.com for at finde kuldioxid-værdier for
Briggs & Stratton EU-typegodkendelsescertifikat for motorer.
Information om genbrug
Genbrug alle kartoner, æsker, brugt olie og batterier i
henhold til de gældende regeringsbestemmelser.
Førersikkerhed
Sikkerhedssymboler og signalord
Sikkerhedsadvarselssymbolet identificerer sikkerhedsoplysninger om farer,
der kan medføre personskader. Et signalord (FARE, ADVARSEL eller FORSIGTIG)
bliver brugt for at illustrere sandsynligheden for og den mulige grad af personskade.
Desuden bruges et faresymbol til at illustrere faretypen.
FARE indikerer en fare, som, hvis den ikke undgås, vil forårsage dødsfald eller alvorlig
personskade.
ADVARSEL indikerer en fare, som, hvis den ikke undgås, kan forårsage dødsfald eller
alvorlig personskade.
FORSIGTIG indikerer en farlig situation, som, hvis den ikke undgås, kan medføre
alvorlig eller moderat personskade.
BEMÆRK angiver oplysninger, der anses som vigtige, men som ikke vedrører farer.
Faresymboler og deres betydninger
Sikkerhedsinformation om
farer, som kan resultere i
personskade.
Læs og forstå
brugervejledningen før
brug af eller servicering af
enheden.
Brandfare Eksplosionsfare
Fare for stød Fare for giftige dampe
Fare fra varm overflade Støjfare - Høreværn
anbefales ved brug i
længere tid.
Fare for flyvende
genstande - Bær
beskyttelsesbriller.
Eksplosionsfare
Fare for forfrysning Fare for tilbageslag
Fare for amputation -
Bevægelige dele
Kemikaliefare
Fare for varme Ætsende fare
Sikkerhedsmeddelelser
ADVARSEL
Briggs & Stratton®-motorer er ikke designet til og må ikke bruges til at drive: fun-karts;
go-karts; terrængående børne-, fridtids- eller sportskøretøjer (ATV’er); motorcykler,
hovercraft; luftfartsprodukter eller køretøjer, der anvendes til konkurrenceformål, som
ikke er sanktioneret af Briggs & Stratton. For yderligere oplysninger om racingprodukter
se www.briggsracing.com. For brug med terrængående og side-by-side ATV’er kontakt
Briggs & Stratton Power Application Center, 1-866-927-3349. Forkert motorbrug kan
medføre alvorlig personskade eller dødsfald.
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Når du påfylder brændstof
Stop motoren. Inden du fjerner brændstofdækslet, skal du vente mindst to (2)
minutter for at sikre dig, at motoren er nedkølet.
Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.
Påfyld ikke for meget brændstof i tanken. Fyld ikke over bunden af
brændstoftankens hals, så der er plads til at brændstoffet kan udvide sig.
Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre
antændelseskilder.
Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og
tilslutninger for revner eller lækager. Udskift beskadigede dele.
Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter
motoren.
Når du starter motoren
Sørg for, at tændrør, lyddæmper, brændstofdæksel og luftfilter (hvis monteret) er
monteret korrekt.
Prøv ikke at starte motoren med tændrøret fjernet.
Hvis motoren er oversvømmet, skal du indstille chokeren (hvis monteret) til
positionen ÅBEN eller KØR. Flyt gashåndtaget (hvis monteret) til positionen
HURTIG, og drej, indtil motoren starter.
Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.
Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.
Når du betjener udstyret
Vip ikke motoren eller enheden, så brændstoffet løber ud.
Brug ikke chokeren (hvis monteret) til at stoppe motoren.
Start, eller betjen ikke motoren, når luftfilterenheden (hvis monteret) eller
luftfilteret (hvis monteret) er fjernet.
Når du udfører vedligeholdelse
Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken
være tom. Hvis den ikke er tom, kan der forekomme brændstoflækage, og dette
kan medføre brand eller eksplosion.
Under vedligeholdelse, hvis det er nødvendigt at vippe enheden, skal du
sørge for, at brændstoftanken, hvis monteret på motoren, er tom, og at
tændrørssiden vender opad. Hvis brændstoftanken ikke er tom, kan der
forekomme brændstoflækage, og dette kan medføre brand eller eksplosion.
Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og
tilslutninger for revner eller lækager. Udskift beskadigede dele.
13
Not for
Reproduction
Udskift ikke regulatorfjederen, forbindelser eller andre dele for at øge motorens
hastighed.
Undlad at slå på svinghjulet med en hammer eller hård genstand. Dette kan
medføre svigt i svinghjulet under drift.
Reservedelene skal have samme udformning, og de skal placeres på præcist
samme måde som de originale dele. Andre dele kan medføre skade eller
personskade.
Når du flytter udstyrets placering
Sørg for, at brændstoftanken er TOM, eller at brændstofhanen er i LUKKET-
stilling.
Når brændstof eller udstyr opbevares med brændstof i brændstoftanken
Da en tændflamme eller andre antændelseskilder kan forårsage eksplosioner,
skal du holde brændstof eller udstyr på afstand af fyr, ovne, vandvarmere eller
andre enheder, der har en tændflamme.
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Motorstart medfører gnister, der kan medføre brand eller eksplosion.
Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.
Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.
ADVARSEL
FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som
er en giftig gas, der kan dræbe på få minutter. Selvom du ikke kan lugte
udstødningsgasser, kan du stadigvæk være udsat for kulilteforgiftning. Hvis du
får kvalme, føler dig svimmel eller svag, mens du bruger dette produkt, skal du
have frisk luft MED DET SAMME. Søg lægehjælp. Du kan være blevet udsat for
kulilteforgiftning.
Kulilte kan opsamles i brugte områder. For at mindske risikoen for kuliltegas
skal du KUN bruge dette produkt udendørs og langt væk fra vinduer, døre og
åbninger.
Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med
batterisupport som specificeret i producentens instruktioner. Røgalarmer kan
ikke fornemme kulilte.
Du MÅ IKKE betjene dette produkt indendørs i hjem, garager, kældre,
krybekældre, skure eller på andre indelukkede steder, også selvom du bruger
ventilatorer eller har åbne døre og vinduer for at sikre ordentlig ventilation. Efter
brug af dette produkt kan kulilte hurtigt samles i disse områder og forblive der i
flere timer.
Anbring ALTID dette produkt i vindretningen, og sørg for, at udstødningen peger
væk fra steder, hvor der er folk til stede.
ADVARSEL
Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm
bliver trukket hurtigere mod motoren, end du kan kontrollere.Konsekvenserne
kan være brækkede knogler, skrammer eller forstuvninger.
For at forhindre tilbageslag når du starter motoren, så træk langsomt i
startsnoren, indtil der mærkes modstand, og træk så kraftigt i den.
Inden du starter motoren, skal du frakoble eller fjerne alt eksternt udstyr og
motorbelastninger.
Sørg for, at direkte tilkoblede dele på udstyret, såsom, men ikke begrænset til,
skæreknive, skovlhjul, remskiver, kædehjul, er korrekt monteret.
ADVARSEL
Roterende dele kan gribe fat i hænder, fødder, hår, tøj eller tilbehør og resultere i
traumatisk amputation eller flænger.
Betjen udstyr med sikkerhedsafskærmningerne monteret korrekt.
Hold hænder og fødder i sikker afstand fra roterende dele.
Fjern smykker, og sørg for, at langt hår er sat op og væk fra alle roterende dele.
Bær ikke løstsiddende tøj eller genstande, som kan blive fanget.
ADVARSEL
Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm
motor, kan der opstå termiske forbrændinger.
Brændbart materiale, såsom blade, græs og krat, kan blive antændt.
Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to
(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.
Fjern affald fra lyddæmperen og motoren.
Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer, afsnit
4442, at bruge eller betjene motoren på ethvert skov-, krat- eller græsdækket område,
medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger
som beskrevet i afsnit 4442. Andre stater eller statsretskredse har eventuelt lignende
love, se statsforskrift 36 CFR, afsnit 261.52. Kontakt en autoriseret fabrikant eller
serviceforhandler angående anskaffelse af en gnistfanger, der er konstrueret til det
udstødningssystem, der er monteret på den pågældende maskine.
ADVARSEL
Tilfældige gnister fra motoren kan forårsage elektrisk stød eller brand og kan
medføre indfiltring, traumatisk amputation eller flænger.
Før du foretager justeringer eller reparationer:
Fjern tændrørskablet, og hold det på behørig afstand af tændrøret.
Frakobl batterikablet fra den negative terminal (gælder kun motorer med
elektrisk start).
Brug kun passende værktøj.
Når du tjekker for gnister:
Brug en godkendt tændrørstester.
Test ikke for gnister med tændrøret fjernet.
ADVARSEL
Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre
forbrændinger eller dødsfald.
Hvis du kan lugte gas
Start ikke motoren.
Tænd ikke for elektriske kontakter.
Brug ikke en telefon i nærheden.
Evakuer området.
Kontakt gasforsyningen eller alarmcentralen.
Funktioner og betjeningsanordninger
Motorens betjeningselementer
Sammenlign henvisningsbogstaverne i figur 1, 2, 3, og 4 med motorens
betjeningsanordninger på den følgende liste:
A. Motorens identifikationsnumre Model-, type- og kodenummer
B. Tændrør
C. Cyklonisk luftfilter
D. Luftfilter med lav profil
E. Oliepind
F. Oliepåfyldning
G. Oliefilter
H. Olieaftapningsprop
I. Olietrykføler
J. Fingerværn
K. Elektrisk starter
L. Startrelæ
M. Regulator / ensretter
N. Karburator - Karburatormodeller
O. Oliekøler (hvis monteret)
P. Lyddæmper (hvis monteret)
Q. Brændstofpumpe
R.
Starterkontakt
1
S.
Gasregulator
1
T.
Chokerregulator(karburatormodeller
1
)
U. Brændstoffilter
V. Omdrejningstæller (hvis udstyret)
1
Nogle motorer og noget udstyr har fjernbetjeningsanordninger. Se udstyrsmanualen for
placering og betjening af fjernbetjeningsanordninger.
Motorfaresymboler og deres betydninger
Motorhastighed - HURTIG Motorhastighed -
LANGSOM
14 vanguardpower.com
Not for
Reproduction
Motorhastighed - STOP TÆND - SLUK
Motorstart
Choker LUKKET
Motorstart
Choker ÅBEN
Brændstofdæksel
Brændstofhane ÅBEN
Brændstofhane LUKKET
Brændstofniveau - Maks.
Undgå at overfylde
Betjening
Olieanbefalinger
Oliekapacitet: Se afsnittetSpecifikationer.
BEMÆRK
Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere
af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal
du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i
denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke
blive repareret under garantien.
Vi anbefaler at bruge olie, der er certificeret af Briggs & Stratton
®
for at opnå den bedste
ydeevne. Andre selvrensende olier af høj kvalitet er tilladt, hvis de er godkendt til SF-,
SG-, SH-, SJ-service eller højere. Undlad at bruge specielle tilsætningsstoffer.
Brug skemaet til at vælge den bedste viskositet til det forventede
udendørstemperaturinterval. Motorer i det meste udstyr til udendørs brug kører
godt med syntetisk olie 5W-30. Til udstyr, der bruges i varmere temperaturer, yder
Vanguard
®
15W-50 syntetisk olie den bedste beskyttelse.
A SAE30- Under 40°F (4°C) vil brugen af SAE30 gøre det svært at starte.
B 10W-30- Over 80°F (27°C) kan brugen af 10W-30 medføre forhøjet
olieforbrug. Kontroller olieniveauet ofte.
C 5W-30
D Syntetisk 5W-30
E
Vanguard
®
syntetisk 15W-50
Kontrollér og påfyld olie
Før du tjekker eller påfylder olie
Kontrollér, at motoren står plant.
Rengør oliepåfyldningsområdet for affald.
Se afsnittet Specifikationer mht. oliekapacitet.
BEMÆRK
Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere
af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal
du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne i
denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil ikke
blive repareret under garantien.
1. Tag oliepinden ud (A, figur 5), og rengør den med en klud.
2. Sæt oliepinden i, og spænd den (A, figur 5).
3. Træk oliepinden op, og kontrollér oliestanden. Sørg for, at olieniveauet når op til
toppen af fuld-mærket (B, figur 5) på oliepinden.
4. Hvis oliestanden er for lav, skal du langsomt påfylde olie i motoroliepåfyldningen
(C, figur 5). Hæld ikke for meget olie på. Vent et minut efter oliepåfyldning, og
kontrollér oliestanden igen. Sørg for, at olieniveauet er korrekt.
5. Sæt oliepinden i, og spænd den (A, figur 5).
Beskyttelsessystem for lav oliestand (hvis
monteret)
Der er monteret en sensor for lav oliestand på nogle motorer. Hvis oliestanden er lav,
viser sensoren enten et advarselslys eller standser motoren. Stop motoren, og følg
disse trin, før du starter motoren.
Kontrollér, at motoren står plant.
Foretag en oliekontrol. Se afsnittet Kontrollér oliestand.
Hvis oliestanden er lav, så tilføj den korrekte mængde olie. Start motoren, og
sørg for, at advarselslyset (hvis monteret) ikke tændes.
Hvis oliestanden ikke er lav, må du ikke starte motoren. Kontakt en autoriseret
serviceforhandler fra Briggs & Stratton for at få rettet olieproblemet.
Anbefalet brændstof
Brændstoffet skal overholde følgende krav:
Ren, frisk blyfri benzin.
Mindst 87 oktan/87 AKI (91 RON). Skal kunne anvendes i højder; se nedenfor.
Benzin med op til 10% ætanol (gasohol) er tilladt.
BEMÆRK
Brug ikke ikke-godkendt benzin, såsom E15 og E85. Der må ikke blandes olie i
benzin, og der må ikke foretages ændringer på motoren, så den fungerer med
alternative brændstoffer. Brug af ikke-godkendt brændstof resulterer i skader på
motorkomponenterne, som ikke bliver repareret under garantien.
For at beskytte brændstofsystemet mod dannelse af gummi, kan brændstoffer tilsættes
en stabilisator. Se afsnittet Opbevaring. Brændstoffer er forskellige. Hvis du oplever
start- eller driftsproblemer, så skift brændstofleverandør eller -mærke. Motoren er
godkendt til at køre på benzin. Emissionskontrolsystemet for motorer med karburator
er EM (motormodifikationer). Emissionskontrolsystemet for motorer med elektronisk
brændstofindsprøjtning er ECM (motorstyringsmodul), MPI (flerportsinjektion) og hvis
udrustet dermed en O2S (iltsensor).
Højder
Ved højder over 1.524 m (5.000fod) er benzin med 85 oktan/85 AKI (89 RON) tilladt.
På motorer med karburator skal der foretages højdetilpasning for at vedligeholde
ydeevnen. Drift uden disse justeringer vil medføre en nedgang i ydelse, en stigning
i brændstofforbrug og øgede emissioner. Kontakt en Briggs & Stratton autoriseret
forhandler for oplysninger om højdejusteringer. Drift af en motor, der er justeret til store
højder, kan ikke anbefales i højder under 2.500 fod (762 m).
På motorer med elektronisk brændstofindsprøjtning (EFI) er det ikke nødvendigt at
foretage justering til brug i højtliggende områder.
Påfyld brændstof
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Når du påfylder brændstof
Stop motoren. Inden du fjerner brændstofdækslet, skal du vente mindst to (2)
minutter for at sikre dig, at motoren er nedkølet.
Fyld brændstoftanken udendørs eller i et område med god luftgennemstrømning.
Påfyld ikke for meget brændstof i tanken. Fyld ikke over bunden af
brændstoftankens hals, så der er plads til at brændstoffet kan udvide sig.
Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre
antændelseskilder.
Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og
tilslutninger for revner eller lækager. Udskift beskadigede dele.
Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter
motoren.
1. Rengør brændstofdækslet for snavs og affaldsrester. Fjern brændstofsdækslet.
2. Fyld brændstoftanken (A, figur 6) med brændstof. Da brændstof udvides, skal du
undlade at fylde op over bunden af brændstoftankens hals (B).
3. Sæt dækslet tilbage på plads.
15
Not for
Reproduction
Start og stop motoren
Start motoren
ADVARSEL
Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm
bliver trukket hurtigere mod motoren, end du kan kontrollere.Konsekvenserne
kan være brækkede knogler, skrammer eller forstuvninger.
For at forhindre tilbageslag når du starter motoren, så træk langsomt i
startsnoren, indtil der mærkes modstand, og træk så kraftigt i den.
Inden du starter motoren, skal du frakoble eller fjerne alt eksternt udstyr og
motorbelastninger.
Sørg for, at direkte tilkoblede dele på udstyret, såsom, men ikke begrænset til,
skæreknive, skovlhjul, remskiver, kædehjul, er korrekt monteret.
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Når du starter motoren
Sørg for, at tændrør, lyddæmper, brændstofdæksel og luftfilter (hvis monteret)
er monteret korrekt.
Prøv ikke at starte motoren med tændrøret fjernet.
Hvis motoren er oversvømmet, skal du indstille chokeren (hvis monteret) til
positionen ÅBEN eller KØR. Flyt gashåndtaget (hvis monteret) til positionen
HURTIG, og drej, indtil motoren starter.
Hvis der er en utæthed af natur- eller LP-gas, må motoren ikke startes.
Da dampe er brandfarlige, må du ikke bruge startvæsker under tryk.
ADVARSEL
FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som
er en giftig gas, der kan dræbe på få minutter. Selvom du ikke kan lugte
udstødningsgasser, kan du stadigvæk være udsat for kulilteforgiftning. Hvis du
får kvalme, føler dig svimmel eller svag, mens du bruger dette produkt, skal du
have frisk luft MED DET SAMME. Søg lægehjælp. Du kan være blevet udsat for
kulilteforgiftning.
Kulilte kan opsamles i brugte områder. For at mindske risikoen for kuliltegas
skal du KUN bruge dette produkt udendørs og langt væk fra vinduer, døre og
åbninger.
Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med
batterisupport som specificeret i producentens instruktioner. Røgalarmer kan
ikke fornemme kulilte.
Du MÅ IKKE betjene dette produkt indendørs i hjem, garager, kældre,
krybekældre, skure eller på andre indelukkede steder, også selvom du bruger
ventilatorer eller har åbne døre og vinduer for at sikre ordentlig ventilation. Efter
brug af dette produkt kan kulilte hurtigt samles i disse områder og forblive der i
flere timer.
Anbring ALTID dette produkt i vindretningen, og sørg for, at udstødningen
peger væk fra steder, hvor der er folk til stede.
BEMÆRK
Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere
af udstyret kan have fyldt olie på motoren. Inden du starter motoren første gang, skal
du sørge for, at olien er ved det rigtige niveau. Tilsæt olie som angivet i instruktionerne
i denne vejledning. Hvis du starter motoren uden olie, vil den blive beskadiget og vil
ikke blive repareret under garantien.
Typer af startsystemer
Før du starter motoren, skal du identificere typen af startsystem på din motor. Din
motor vil have en af disse typer.
Elektronisk brændstofindsprøjtning (EFI): Et EFI-system har ikke en choker
eller en primer.
Chokersystem: Denne type system har en choker, der skal bruges i kølige
temperaturer. Nogle modeller har en separat chokerregulering, mens andre har
en kombination af choker- og gasregulering. Den har ikke en primerfunktion.
BEMÆRK:Dit udstyr kan have fjernbetjeninger. Se udstyrsmanualen for placering og
betjening af fjernbetjeningen.
Elektronisk brændstofindsprøjtning (EFI)
1. Kontroller motorolien. Se afsnittetKontrol af olieniveau.
2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.
3. Sæt brændstofhanen (A, figur 7) i positionen ÅBEN, hvis monteret.
4. Sæt gasregulatoren (B, figur 7), hvis monteret, i stillingen HURTIG. Betjen motoren
i positionen HURTIG.
5. Drej den elektriske startkontakt (D, figur 7) til stillingen TIL eller START.
BEMÆRKStarterens levetid kan forlænges ved at bruge korte startcyklusser (maks.
fem sekunder). Vent ét minut mellem startcyklusserne.
Hvis motoren ikke starter efter 3 eller 4 forsøg, skal du kontakte din lokale forhandler,
gå til vanguardpower.com eller ringe til 1-800-999-9333.
Chokersystem
1. Kontroller motorolien. Se afsnittetKontrol af olieniveau.
2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.
3. Sæt brændstofhanen (A, figur 7) i positionen ÅBEN, hvis monteret.
4. Sæt gasregulatoren (B, figur 7), hvis monteret, i stillingen HURTIG. Betjen motoren
i positionen HURTIG.
5. Flyt chokerregulatoren (C, figur 7) eller kombinationen af choker og gas (B, C) til
stillingen LUKKET.
BEMÆRK:For at starte motoren med et tørlagt brændstofsystem er der behov
for ekstra starttid i chokerpositionen. Det giver brændstofpumpen tid til at fylde
brændstofsystemet op.
6. Drej tændingskontakten (D, figur 7) til stillingen TIL eller START.
7. Hvis motoren starter men ikke kan fortsætte med at køre, skal du flytte
chokerregulatoren (C, figur7) til stillingen ÅBEN for at starte motoren.
BEMÆRKStarterens levetid kan forlænges ved at bruge korte startcyklusser (maks.
fem sekunder). Vent ét minut mellem startcyklusserne.
8. Når motoren bliver varm, skal du flytte chokerregulatoren (C, figur 7) til stillingen
ÅBEN.
Hvis motoren ikke starter efter 3 eller 4 forsøg, skal du kontakte din lokale forhandler,
gå til vanguardpower.com eller ringe til 1-800-999-9333.
Stop motoren
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Brug ikke chokeren (hvis monteret) til at stoppe motoren.
1. Med gasregulatoren i stillingen LANGSOM, drej den elektriske startkontakt (D,
figur7) til stillingen FRA. Tag nøglen ud, og opbevar den på et sikkert sted uden for
børns rækkevidde.
2. Efter at motoren er standset, drej brændstofhanen (A, figur 7) til positionen
LUKKET, hvis monteret.
Vedligeholdelse
Vedligeholdelsesoplysninger
ADVARSEL
Under vedligeholdelse, hvis det er nødvendigt at vippe enheden, skal du sørge for, at
brændstoftanken, hvis monteret på motoren, er tom, og at tændrørssiden vender opad.
Hvis brændstoftanken ikke er tom, kan der forekomme brændstoflækage, og dette kan
medføre brand eller eksplosion. Hvis motoren vippes i en anden retning, starter den ikke
nemt på grund af olie- eller brændstofforurening af luftfilteret eller tændrøret.
Vi anbefaler, at du kontakter en autoriseret serviceforhandler fra Briggs & Stratton
vedrørende al vedligeholdelse og eftersyn af motoren og motordele.
BEMÆRK
Alle komponenter, der bruges til at bygge dette produkt, skal forblive på plads for korrekt
drift.
ADVARSEL
Tilfældige gnister fra motoren kan forårsage elektrisk stød eller brand og kan
medføre indfiltring, traumatisk amputation eller flænger.
Før du foretager justeringer eller reparationer:
Fjern tændrørskablet, og hold det på behørig afstand af tændrøret.
Frakobl batterikablet fra den negative terminal (gælder kun motorer med
elektrisk start).
Brug kun passende værktøj.
Når du tjekker for gnister:
Brug en godkendt tændrørstester.
Test ikke for gnister med tændrøret fjernet.
16 vanguardpower.com
Not for
Reproduction
Udførelse af udledningskontrol
Ved vedligeholdelse, udskiftning eller reparation af udledningskontrolenheder
og systemer, skal du kontakte et kvalificeret offroad-motorværksted eller
en servicetekniker. For at få udført udledningskontrolservice “uden beregning”
skal arbejdet imidlertid udføres af en autoriseret forhandler. Se erklæringer om
udledningskontrol.
Vedligeholdelsesskema
8-timers intervaller eller dagligt
Kontroller oliestanden i motoren.
Rengør området omkring lyddæmperen og betjeningsanordningerne.
100 timers intervaller eller årligt
Rengør eller udskift luftfilteret
1, 2
.
Udskift motorolien og filteret.
Udskift oliefilteret (hvis monteret).
Udskift tændrørene.
Tjek lyddæmper og gnistfanger.
Servicér udstødningssystemet.
250 timers intervaller eller årligt
Tjek ventilfrirummet. Juster om nødvendigt.
400 timers intervaller eller årligt
Udskift luftfilteret
2
.
Udskift brændstoffilteret.
Servicér luftkølesystemet
1
.
Rengør finner på oliekøleren
1
.
Intervaller på 600 timer
Udskift sikkerhedsfilteret, hvis monteret.
1
Rengør oftere under støvede forhold, eller når luftbåret snavs er til stede.
2
Ved hver 3. udskiftning af luftfilteret skal det indvendige sikkerhedsfilter udskiftes (hvis
monteret).
Elektronisk brændstofindsprøjtning (EFI)
EFI-systemet overvåger motortemperatur, motorhastighed og batterispænding under
start og opvarmning af motoren. Systemet skal ikke justeres. Hvis der opstår start- eller
betjeningsbesvær, skal du kontakte en autoriseret Briggs & Stratton-serviceforhandler.
BEMÆRKSørg for at følge nedenstående trin, ellers kan der opstå skader på EFI-
systemet.
Start ALDRIG motoren, hvis batterikablerne er løse.
Drej nøglen til FRA, før du frakobler, fjerner og/eller monterer batteriet.
Start ALDRIG motoren ved hjælp af en batterioplader.
Frakobl IKKE batterikablerne under motordrift.
Når du tilslutter batterikablerne, skal du først tilslutte pluskablet (+) og derefter
minuskablet (-) til batteriet.
Når batteriet oplades, skal du dreje tændingskontakten til stillingen FRAog
frakoble minuskablet (-) fra batteriet.
Sprøjt IKKE vand direkte på det elektroniske styremodul.
Karburator og motorhastighed
Foretag ikke justeringer af karburatoren eller motorhastigheden. Karburatoren er
fabriksindstillet til at virke effektivt under de fleste omstændigheder. Undlad at ændre
ved regulatorfjederen, forbindelser eller andre dele, der er med til at øge motorens
hastighed. Hvis der er behov for justering, så kontakt en autoriseret serviceforhandler fra
Briggs & Stratton for service.
BEMÆRK
Denne udstyrsproducent specificerer maks. hastighed for motoren, som er installeret
på udstyret. Motoren må ikke køre med højere hastighed. Hvis du ikke er sikker på,
hvad maks. hastigheden er på udstyret, eller hvilken motorhastighed, der er indstillet
fra fabrikken af, så kontakt en autoriseret serviceforhandler fra Briggs & Stratton for
hjælp. For sikker og korrekt brug af udstyret skal motorhastigheden kun justeres af en
uddannet servicetekniker.
Eftersyn af tændrøret
Kontrollér afstanden for tændrøret (A, figur 8) med en afstandsmåler (B). Indstil om
nødvendigt tændrørsgabet. Monter og fastspænd tændrøret til det korrekte moment. Se
afsnittet Specifikationer for specifikationer mht. afstand og drejningsmoment.
BEMÆRK:I nogle lande kræves det af lokal lov, at du bruger et modstandstændrør
til at dæmpe tændingssignalet.Hvis der blev installeret et modstandstændrør af
udstyrsproducenten, skal du udskifte den med samme type.
Eftersyn af udstødningssystemet
ADVARSEL
Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm
motor, kan der opstå termiske forbrændinger.
Brændbart materiale, såsom blade, græs og krat, kan blive antændt.
Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to
(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.
Fjern affald fra lyddæmperen og motoren.
Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer, afsnit
4442, at bruge eller betjene motoren på ethvert skov-, krat- eller græsdækket område,
medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger
som beskrevet i afsnit 4442. Andre stater eller statsretskredse har eventuelt lignende
love, se statsforskrift 36 CFR, afsnit 261.52. Kontakt en autoriseret fabrikant eller
serviceforhandler angående anskaffelse af en gnistfanger, der er konstrueret til det
udstødningssystem, der er monteret på den pågældende maskine.
Fjern affald fra området omkring lyddæmperen og cylinderen. Undersøg lyddæmperen
for revner, korrosion eller andre skader. Fjern udkastskærmen eller gnistfangeren, hvis
monteret, og undersøg for skader eller kulstofblokering. Hvis der er skade, skal der
monteres reservedele, før du betjener udstyret.
ADVARSEL
Reservedelene skal have samme udformning, og de skal placeres på præcist samme
måde som de originale dele. Andre dele kan medføre skade eller personskade.
Skift motorolie
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm
motor, kan der opstå termiske forbrændinger.
Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken
være tom. Hvis den ikke er tom, kan der forekomme brændstoflækage og dette
kan forårsage brand eller eksplosion.
Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to
(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.
Brugt olie er et farligt affaldsprodukt og skal kasseres korrekt. Må ikke bortskaffes
sammen med husholdningsaffald. Kontakt de lokale myndigheder, dit servicecenter
eller din forhandler for oplysninger om sikker bortskaffelse eller korrekt aflevering til en
genbrugsstation.
Aftapning af olie
1. Med motoren STANDSET men stadig varm trækkes ledningen til tændrøret ud (D,
figur 9) og holdes væk fra tændrøret (E).
2. Fjern oliepinden (A, figur 10).
3. Afmonter olieaftapningsproppen (F, figur 11). Tap olien ud i en godkendt beholder.
4. Monter og spænd olieaftapningsproppen (F, figur 11).
Skift oliefilter, hvis monteret
1. Tap olien af motoren. Se afsnittet Aftapning af olie.
2. Fjern oliefilteret (H, figur 12), ogkassér det korrekt.
3. Inden du monterer det nye oliefilter, bør du smøre oliefilterets pakning let medren
olie.
4. Monter oliefilteret med hånden, indtil pakningenharkontaktmed oliefilterets
tilpasningsstykke, og fastgør derefter oliefilteret med 1/2 til 3/4 omgange.
5. Påfyld olie. Se afsnittet Påfyld olie.
6. Start, og brugmotoren. Når motoren er varm, skal der kontrolleresfor olielækage.
7. Stop motoren. Sørg for, at olieniveauet når op til toppen af fuld-mærket (B, figur 5)
på oliepinden.
Påfyld olie
Kontrollér, at motoren står plant.
Rengør oliepåfyldningsområdet for al snavs.
Se afsnittetSpecifikationermht. oliekapacitet.
1. Fjern oliepinden (A, figur 10). Brug en ren klud til at fjerne olie fra oliepinden.
17
Not for
Reproduction
2. Hæld langsomt olie i motorpåfyldningen (C, figur 10). Undgå at overfylde. Vent i
et minut, og kontrollér oliestanden.
3. Sæt oliepinden i, og spænd den (A, figur 10).
4. Træk oliepinden op, og kontrollér oliestanden. Den korrekte olieniveau findes på
toppen af fuld-mærket (B, figur 10) på oliepinden.
5. Sæt oliepinden i, og spænd den (A, figur 10).
6. Tilslut tændrørsledningerne (D, figur 9) til tændrørene (E).
Eftersyn af luftfilteret
ADVARSEL
Benzindampe er brændbare og eksplosive. Brand eller eksplosion kan medføre
forbrændinger eller dødsfald.
Startikke motoren, og lad den ikke køre uden luftfilterenheden (hvis monteret)
eller luftfilteret (hvis monteret).
BEMÆRK
Undlad at bruge komprimeret luft eller rengøringsmidler til rengøring af filteret.
Komprimeret luft kan beskadige filteret, og rengøringsmidler vil opløse filteret.
Se Vedligeholdelsesoversigten for servicekrav.
Forskellige modeller bruger et skum- eller papirfilter. Nogle modeller kan også have et
forfilter, der kan vaskes og genbruges. Sammenlign illustrationerne i denne manual med
den type, der er installeret på din motor, og servicér i overensstemmelse hermed.
Cyklonisk luftfilter
1. Åbn monteringsanordningerne (A, figur 13), og afmonter dækslet (B).
2. Fjern luftfilteret (C, figur 13).
3. For at løsne urenheder bankes luftfilteret forsigtigt mod en hård overflade. Hvis
luftfilteret er meget snavset, udskift det med et nyt filter.
4. Sikkerhedsfilteret (D, figur 13) kan, hvis monteret, fjernes ved at trække det
forsigtigt væk fra luftfilterenheden (E). Sørg for, at hverken snavs eller affald
trænger ind i motoren.
5. Monter det nye sikkerhedsfilter (D, figur 13) i luftfilterenheden (E).
6. Monter luftfilteret (C, figur 13) over sikkerhedsfilteret (D).
7. Monter dækslet (B, figur 13), og luk monteringsanordningerne (A).
Luftfilter, lav profil
1. Fjern monteringsanordningerne (A, figur 14).
2. Afmonter dækslet (B, figur 14).
3. Fjern monteringsanordningerne (C, figur 14), og holderen (D).
4. Fjern luftfilteret (E, figur 14).
5. Fjern forfilteret (F, figur 14), hvis monteret, fra luftfilteret (E).
6. For at løsne snavs bankes luftfilteret (E, figur 14) forsigtigt mod en hård overflade.
Hvis luftfilteret er meget snavset, udskift det med et nyt filter.
7. Rens forfilteret (F, figur 14), hvis monteret, med flydende rengøringsmiddel i vand.
Sørg for, at forfilteret er helt tørt. Smør ikke forfilteret.
8. Saml det tørre forfilter (F, figur 14), hvis monteret, på luftfilteret (E).
9. Monter luftfilteret (E, figur 14) med holderen (D) og fastgørelseselementerne (C).
10. Monter dækslet (B, figur 14) med fastgørelseselementerne (A). Sørg for, at
fastgørelseselementerne er strammet.
Vedligeholdelse af kølesystemet
ADVARSEL
Under drift bliver motoren og lyddæmperen varm. Hvis du rører ved en varm
motor, kan der opstå termiske forbrændinger.
Brændbart affald, såsom blade, græs og krat, kan blive antændt.
Før du berører motoren eller lyddæmperen, skal du stoppe motoren og vente to
(2) minutter. Sørg for, at motoren og lyddæmperen er sikre at røre ved.
Fjern affald fra lyddæmperen og motoren.
BEMÆRK
Brug ikke vand til at rengøre motoren. Vand kan forårsage forurening af
brændstofsystemet. Brug i stedet en børste eller en tør klud til at rengøre motoren.
Dette er en luftkølet motor. Snavs og rester kan stoppe luftstrømmen og medføre, at
motoren overophedes, så motorens ydelse svækkes, og dens levetid reduceres.
1. Anvend en børste eller en tør klud til at fjerne snavs fra luftindsugningsområdet (A,
figur15).
2. Sørg for, at forbindelseskabler, fjedre og betjeningsanordninger (B, figur15, 16) er
rene.
3. Hold området omkring og bag lyddæmperen (C, figur15, 16) fri for brændbart affald
for at undgå antænding af dette.
4. Sørg for, at oliekølerribberne (D, figur15) er fri for snavs og affald.
5. Løsn monteringsanordningerne (E, figur15, 16), og afmonter
affaldsadgangspanelerne (F). Fjern græs og snavs, der har ophobet sig på
cylinderne.
6. Installer affaldsadgangspanelerne (F, figur15, 16), og fastgør dem med
monteringsanordningerne(E).
Efter nogen tid kan der samle sig snavs i cylinderens køleribber, hvilket kan medføre,
at motoren overophedes. Dette snavs kan ikke fjernes uden delvist at skille motoren
ad. Få en autoriseret Briggs & Stratton-serviceforhandler til at inspicere og rengøre
luftkølesystemet som anbefalet i Vedligeholdelsesoversigten.
Vedligeholdelse af brændstofsystemet
ADVARSEL
Benzin og benzindampe er brændbare og eksplosive. Brand eller eksplosion kan
medføre forbrændinger eller dødsfald.
Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre
antændelseskilder.
Undersøg ofte brændstofledninger, brændstoftank, brændstofdæksel og
tilslutninger for revner eller lækager. Udskift beskadigede dele.
Før rengøring eller udskiftning af brændstoffilteret skal brændstoftanken
tømmes, eller brændstofhanen lukkes.
Hvis der spildes brændstof, skal du vente, indtil det tørrer, inden du starter
motoren.
Reservedelene skal have samme udformning, og de skal placeres på præcist
samme måde som de originale dele. Andre dele kan medføre skade eller
personskade.
Brændstoffilter, hvis monteret
1. Før rengøring eller udskiftning af brændstoffilteret (A, figur 17) skal
brændstoftanken tømmes eller brændstofhanen lukkes. Hvis brændstoftanken ikke
tømmes, kan brændstof lække ud og forårsage brand eller eksplosion.
2. Brug en tang til at klemme tapperne (B, figur 17) på klemmerne (C) sammen, og flyt
derefter klemmerne væk fra brændstoffilteret (A). Drej og træk brændstofslangerne
(D) af brændstoffilteret.
3. Tjek brændstofslangerne (D, figur 17) for revner eller utætheder. Udskift efter
behov.
4. Udskift brændstoffilteret (A, figur 17) med et originalt udskiftningsfilter.
5. Fastgør brændstofslangerne (D, figur 17) med klemmer (C).
Opbevaring
Brændstofsystem
Se figur: 18.
Opbevar motoren på en plan overflade (almindelig driftsposition). Fyld brændstoftanken
(A, figur 18) med brændstof. Fyld ikke over brændstoftankens hals (B), da brændstoffet
kan ekspandere.
Brændstof kan blive forældet, når det opbevares i en opbevaringsbeholder i over 30
dage. Hver gang du fylder beholderen med brændstof, skal du tilføjetil brændstoffet
i overensstemmelse med producentens instruktioner. Det holder brændstoffet
frisk og formindsker antallet af brændstofrelaterede problemer eller forurening i
brændstofsystemet.
Det er ikke nødvendigt af tømme motoren for brændstof, nårtilføjes i henhold til
instruktionerne. TÆND motoren i to minutter før opbevaring for at føre brændstoffet og
stabilisatoren gennem brændstofsystemet.
Hvis benzinen i motoren ikke er blevet behandlet med en brændstofstabilisator,
skal den udtømmes i en godkendt beholder. Lad motoren køre, indtil den stopper
på grund af mangel på brændstof. Det anbefales at bruge en brændstofstabilisator i
opbevaringsbeholderen for at holde brændstoffet frisk.
Motorolie
Skift motorolien, mens motoren stadig er varm. Se afsnittet Udskift motorolien.
Fejlfinding
Hjælp
Hvis du har brug for hjælp, skal du kontakte din lokale forhandler eller gå til
vanguardpower.com eller ringe til 1-800-999-9333 (i USA).
18 vanguardpower.com
Not for
Reproduction
Specifikationer
Specifikationer og reservedele
Modeller: 540000 , 54E000
Forskydning 54.68 ci (896 cc)
Boring 3.366 tommer (85,5 mm)
Slaglængde 3.071 tommer (78,0 mm)
Oliekapacitet 78 - 80oz (2,3 - 2,4L)
Tændrørsgab .030 tommer (,76 mm)
Tilspændingsmoment for tændrør 180pund-tommer (20Nm)
Rotorelektrodeafstand .005 - .008 tommer (,13 - ,20 mm)
Ventilspillerum (indsugning) .004 - .006 tommer(,10 - ,15 mm)
Ventilspillerum (udstødning) .007 - .009 tommer (,18 - ,23 mm)
Modeller: 610000, 61E000, 61G200, 61G300
Forskydning 60.60 ci (993 cc)
Boring 3.366 tommer (85,5 mm)
Slaglængde 3.406 tommer (86,5 mm)
Oliekapacitet 78 - 80oz (2,3 - 2,4L)
Tændrørsgab .030 tommer (,76 mm)
Tilspændingsmoment for tændrør 180pund-tommer (20Nm)
Rotorelektrodeafstand .005 - .008 tommer (,13 - ,20 mm)
Ventilspillerum (indsugning) .004 - .006 tommer(,10 - ,15 mm)
Ventilspillerum (udstødning) .007 - .009 tommer (,18 - ,23 mm)
Reservedele - Modeller: 540000, 54E000,
610000, 61E000, 61G200, 61G300
Reservedel Delnummer
Cyklonisk luftfilter (figur 13) 841497
Cyklonisk sikkerhedsfilter (figur 13) 821136
Luftfilter, lavprofil (figur 14) 692519
Forfilter, lavprofil (figur 14) 692520
Olie ‒ SAE 30 100028
Oliefilter 842921
Brændstoffilter 691035
Tændrørsmodstand 491055
Platintændrør med ekstra lang levetid 5066
Tændrørsnøgle 19374
Gnisttester 19368
Motoreffekten falder med 3,5% for hver 1.000fod (300m) over havets overflade og
med 1% for hver 10°F (5,6°C) over 77°F (25°C). Motoren kan køre tilfredsstillende
ved en hældning på op til 15°. Yderligere oplysninger om sikre grænseværdier for drift
på hældninger findes i udstyrets betjeningsvejledning.
Nominel belastning
Nettobelastningen for separate benzinmotormodeller er mærket i henhold til SAE
(sammenslutningen af bilingeniører)-kode J1940, procedure til klassificering af lav
motorkraft og drejningsmoment, og den er klassificeret i henhold til SAE J1995.
Drejningsmomentværdier er målt ved 2.600 o/min. for motorer med “rpm” angivet
på mærkaten og 3.060 o/min. for alle andre; hestekræftværdier er angivet ved
3.600 o/min. Bruttoeffektkurverne kan ses på www.BRIGGSandSTRATTON.COM.
Nettokraftværdier bliver målt med udstødnings- og luftfilter monteret, hvorimod
bruttokraftværdier bliver målt uden disse anordninger. Faktisk bruttomotoreffekt vil være
højere end nettomotoreffekt og er bl.a. påvirket af lokale driftsforhold og variationer
fra motor til motor. På grund af det store udvalg af ekstraudstyr, der kan benyttes
sammen med motorer, yder benzinmotoren måske ikke den forventede bruttoeffekt,
når den anvendes med et bestemt stykke ekstraudstyr. Forskellen skyldes mange
forskellige faktorer, herunder eksempelvis de forskellige motordele (luftfilter, udstødning,
opladning, kølesystem, karburator, brændstofpumpe osv.), anvendelsesbegrænsninger,
omgivelsernes driftsforhold (temperatur, fugtighed, højde) samt motor-til-motor-variation.
På grund af fabrikations- og kapacitetsbegrænsninger kan Briggs & Stratton erstatte en
motor med højere effekt for denne motor.
Garanti
Briggs & Stratton – Motorgaranti
Gældende fra januar 2019
Begrænset garanti
Briggs & Stratton garanterer, at i løbet af garantiperioden, der er angivet nedenfor,
vil vi reparere eller udskifte enhver del, der er defekt i materiale eller håndværk eller
begge dele, uden beregning. Transportomkostninger i forbindelse med et produkt, som
indleveres til reparation eller udskiftning under denne garanti, afholdes af køberen.
Denne garanti er gyldig inden for tidsperioderne og underlagt nedenstående betingelser.
Find den nærmeste autoriserede serviceforhandler på kortet over forhandlere på
BRIGGSandSTRATTON.COM i forbindelse med service under garantien. Køberen skal
kontakte den autoriserede serviceforhandler og derefter stille produktet til rådighed for
den autoriserede serviceforhandler med henblik på inspektion og afprøvning.
Der ydes ikke nogen anden udtrykkelig garanti. Underforståede garantier,
inklusive garantier for salgbarhed og egnethed til et bestemt formål, er begrænset
til garantiperioden, der er angivet nedenfor, eller i den udstrækning loven tillader.
Ansvar for hændelige skader eller følgeskader er udelukket, i det omfang lovgivningen
tillader udelukkelse. Visse stater eller lande tillader ikke begrænsninger på, hvor lang
tid en underforstået garanti varer, og visse stater eller lande tillader ikke udelukkelse
eller begrænsning af tilfældig skade eller følgeskade, så ovenstående begrænsning
og udelukkelse er måske ikke gældende for dig. Denne garanti giver dig specifikke,
juridiske rettigheder, og du kan endvidere have andre rettigheder, som kan variere fra
land til land
4
.
Vilkår for standardgaranti
1, 2, 3
Vanguard®; Commercial Series
3
Forbrugeranvendelse - 36 måneder
Erhvervsmæssig anvendelse - 36 måneder
XR-serien
Forbrugeranvendelse - 24 måneder
Erhvervsmæssig anvendelse - 24 måneder
Alle andre motorer med Dura-Bore™ støbejernsboring
Forbrugeranvendelse - 24 måneder
Erhvervsmæssig anvendelse - 12 måneder
Alle andre motorer
Forbrugeranvendelse - 24 måneder
Erhvervsmæssig anvendelse - 3 måneder
1
Dette er vores vilkår for standardgaranti, men der kan lejlighedsvist være
ekstra garantidækning, der ikke var fastslået på tidspunktet for offentliggørelsen.
Hvis du ønsker en liste over gældende garantivilkår for din motor, så gå til
BRIGGSandSTRATTON.com, eller kontakt din autoriserede Briggs & Stratton-
serviceforhandler.
2
Der er ikke garanti på motorer på udstyr, der bruges til primæreffekt i stedet
for et hjælperedskab; standbygeneratorer, der anvendes til kommercielle
formål, hjælpekøretøjer, der overstiger 25mph, eller motorer, der bruges til
konkurrencemæssige motorløb eller på kommercielle eller lejebaserede baner.
3
Vanguard installeret på standbygeneratorer: 24 måneders forbrugeranvendelse,
ingen garanti for erhvervsmæssig anvendelse. Kommerciel serie med
fremstillingsdato før juli 2017: 24 måneder ved privat anvendelse, 24 måneder ved
erhvervsmæssig anvendelse.
4
I Australien - Vores produkter sælges med en garanti, der ikke kan bortfalde
i henhold til den australske forbrugerlovgivning. Du er berettiget til en erstatning
eller refusion i tilfælde af en væsentlig defekt eller til kompensation for ethvert
forudseeligt tab eller skade. Du er derudover berettiget til at få dine varer repareret
eller erstattet, hvis varerne ikke lever op til kvaliteten, og manglen ikke er i
forbindelse med en væsentlig defekt. I forbindelse med service under garantien
findes den nærmeste autoriserede serviceforhandler på kortet over forhandlere på
BRIGGSandSTRATTON.COM, ved at ringe til 1300 274 447 eller ved at sende en
e-mail eller skrive til [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW, Australia, 2170.
Garantiperioden starter på købsdatoen for den første almindelige eller erhvervsmæssige
bruger. “Privat brug” betyder brug i personlig beboelseshusholdning af en detailkunde.
“Erhvervsmæssig brug” betyder al anden form for brug, inklusive erhvervsmæssigt,
indkomstdannende eller lejebaseret formål. Når en motor har været anvendt
erhvervsmæssigt, skal den herefter anses for at være en motor til erhvervsbrug i
henhold til denne garanti.
Gem dit købsbevis. Hvis du ikke kan fremvise bevis for den oprindelige
købsdato på det tidspunkt, hvor du anmoder om garantiservice, vil produktets
produktionsdato blive brugt som grundlag for garantien. Det er ikke nødvendigt at
registrere dit produkt for at opnå garanti på Briggs & Stratton-produkter.
Om garantien
Denne garanti dækker alene motor-relaterede materiale- og/eller fremstillingsfejl og ikke
udskiftning eller tilbagebetaling for det redskab, hvorpå motoren måtte være monteret.
19
Not for
Reproduction
Rutinemæssig vedligeholdelse, optuninger, justeringer eller normal slitage dækkes ikke
under denne garanti. På samme måde gælder denne garanti heller ikke, hvis motoren er
ændret eller modificeret, eller hvis motorens serienummer er ødelagt eller fjernet. Denne
garanti dækker ikke motorskade eller driftsproblemer som følge af:
1. Brug af dele, der ikke er originale dele fra Briggs & Stratton
2. Betjening af motoren med utilstrækkelig, forurenet eller forkert type olie
3. Brug af forurenet eller gammel olie, benzin med mere end 10% etanol eller brug
af alternative brændstoffer som petroleumsvæske eller naturgas på motorer, der
ikke oprindeligt er udviklet/fremstillet af Briggs & Stratton til at fungere med sådanne
brændstoffer
4. Snavs, der er trængt ind i motoren på grund af utilstrækkelig vedligeholdelse af
luftrensesystemet eller genmontering
5. Stød mod et objekt med skærebladet i en roterende plæneklipper, løse eller forkert
installerede bladadaptere, rotorer eller andet udstyr koblet på krumtapakslen eller
for høj V-remspænding
6. Tilhørende dele eller tilbehør som koblinger, transmissioner, udstyrskontroller osv.,
som ikke leveres af Briggs & Stratton
7. Overophedning på grund af græsslåning, snavs og affald eller gnaverreder,
der tilstopper kølefinnerne eller svinghjulsområdet eller drift af motoren uden
tilstrækkelig ventilation
8. Overdreven vibration på grund af for høj hastighed, løs motormontering, løse eller
ubalancerede skæreblade eller rotorer eller forkert kobling af udstyrskomponenter
på krumtapakslen
9. Misbrug, mangel på rutinevedligeholdelse, forsendelse, håndtering eller udstyrets
opbevaring på lager eller forkert motorinstallation.
Servicegarantien er kun tilgængelig via autoriserede Briggs & Stratton-
serviceforhandlere. Find din nærmeste serviceforhandler på vores forhandlerkort
på BRIGGSandSTRATTON.COM, eller ved at ringe til 1-800-233-3723 (i USA).
80004537 (Rev. F)
20 vanguardpower.com
Not for
Reproduction
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Simplicity 54E177-0009-J1 Ohjekirja

Tyyppi
Ohjekirja