Yamaha MOX6 Omistajan opas

Merkki: Yamaha

Malli: MOX6

Luokka: Supplementary music equipment

Tyyppi: Omistajan opas

Tämä ohje sopii myös

MOX8

MOX6/MOX8 Editor Installation Guide 1

ATTENTION

PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY

PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS

BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION (“YAMAHA”).

BY DOWNLOADING, INSTALLING, COPYING, OR OTHERWISE USING THIS SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS

OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT DOWNLOAD, INSTALL, COPY, OR OTHERWISE USE THIS

SOFTWARE. IF YOU HAVE DOWNLOADED OR INSTALLED THE SOFTWARE AND DO NOT AGREE TO THE TERMS, PROMPTLY DELETE THE

SOFTWARE.

1. GRANT OF LICENSE AND COPYRIGHT

Yamaha hereby grants you the right to use one copy of the software program(s) and data (“SOFTWARE”) accompanying this Agreement. The

term SOFTWARE shall encompass any updates to the accompanying software and data. The SOFTWARE is owned by Yamaha and/or Yamaha’s

licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions. While you are entitled to claim ownership of the data

created with the use of SOFTWARE, the SOFTWARE will continue to be protected under relevant copyrights.

• You may use the SOFTWARE on your computer.

• You m ay make one copy of the SOFTWARE in machine-readable form for backup purposes only, if the SOFTWARE is on media where

such backup copy is permitted. On the backup copy, you must reproduce Yamaha's copyright notice and any other proprietary legends

that were on the original copy of the SOFTWARE.

• You m ay permanently transfer to a third party all your rights in the SOFTWARE, provided that you do not retain any copies and the

recipient reads and agrees to the terms of this Agreement.

2. RESTRICTIONS

• You m ay n o t engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE

by any method whatsoever.

• You m ay n o t reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the

SOFTWARE.

• You m ay n o t electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other

computers.

• You m ay n o t use the SOFTWARE to distribute illegal data or data that violates public policy.

• You m ay n o t initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation.

Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following

restrictions which you must observe.

• Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner.

• Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners

in public without permission of the copyright owner.

• The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified

without permission of the copyright owner.

3. TERMINATION

This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or

provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such

termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof.

4. DISCLAIMER OF WARRANTY ON SOFTWARE

You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided

“AS IS” and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY

DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS.

SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR

REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS IN THE

SOFTWARE WILL BE CORRECTED.

SOFTWARE LICENSING AGREEMENT

MOX6/MOX8 Editor

Installation Guide

MOX6/MOX8 Editor

Installation Guide

MOX6/MOX8 Editor Installation Guide 2

5. LIMITATION OF LIABILITY

YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT

SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF

THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha's total liability to you for all damages, losses and causes of action (whether in

contract, tort or otherwise) exceed the amount paid for the SOFTWARE.

6. THIRD PARTY SOFTWARE

Third party software and data (“THIRD PARTY SOFTWARE”) may be attached to the SOFTWARE. If, in the written materials or the electronic data

accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must

abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY

SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any

way for the THIRD PARTY SOFTWARE or your use thereof.

• Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL

IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE.

• Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE.

• Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or

consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD

PARTY SOFTWARE.

7. G E N E R A L

This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute

or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this

Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect.

8. COMPLETE AGREEMENT

This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written

materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this

Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of

Yamaha.

• The software and this Installation Guide are the exclusive copyrights of Yamaha Corporation.

• Please read carefully the Software Licensing Agreement at the front of this Installation Guide before installing the application.

• Copying of the software or reproduction of this Installation Guide in whole or in part by any means is expressly forbidden without the written

consent of the manufacturer.

• Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for

the results of the use of this Installation Guide and the software.

• Future upgrades of application and system software (e.g., firmware of the products) and any changes in specifications and functions will be

announced at the following website. http://www.yamahasynth.com/

• The screen displays as illustrated in this Installation Guide are for instructional purposes, and may appear somewhat different from the

screens which appear on your computer.

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for

your personal use.

• Windows is a registered trademark of Microsoft

Corporation in the United States and other countries.

• Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

• Steinberg and Cubase are the registered trademarks of Steinberg Media Technologies GmbH.

• The company names and product names in this Installation Guide are the trademarks or registered trademarks of their respective companies.

Special Notices

MOX6/MOX8 Editor Installation Guide 3

MOX6/MOX8 Editor is a convenient tool which lets you edit and save the various parameters of your MOX6/MOX8

synthesizer. These include Common/Part Mixing parameters (edited in the Song or Pattern mode of the MOX6/

MOX8) such as Volume, Pan, EG, and Cutoff, as well as parameters of a Voices assigned to each Part (edited in the

Voice mode of the MOX6/MOX8). Thanks to the easy-to-understand graphical interface, you can edit various

parameters of the MOX6/MOX8 right from your computer—using the mouse to adjust the virtual knobs, sliders, and

buttons and entering values from the computer keyboard. Finally, all the changes you have made can be saved to

your computer or transmitted to the MOX6/MOX8 instrument. You can use this MOX6/MOX8 Editor as a plug-in for

the software listed below.

•Studio Manager

• DAW application software compatible with Studio Connections

The actual installation steps and the use of the software itself differs depending on the operating system that you

are using. Please refer to the appropriate installation instructions.

1 Verify that your system meets the operating requirements of each software program. .......... page 4

2 Install the appropriate driver to your computer.......................................................................................... page 5

3 Install the Studio Manager and the MOX6/MOX8 Editor. ........................................................................ page 6

4 Start up the Studio Manager, then start up the MOX6/MOX8 Editor.................................................. page 8

For subsequent operations, refer to the PDF manual accessed from the [HELP] menu in the respective software

program.

Precautions when using the USB TO HOST connector

When connecting the computer to the USB TO HOST connector, make sure to observe the following points. Failing to do so

risks freezing the computer and corrupting or even losing the data. If the computer or the instrument freezes, turn the power

to the instrument off or restart the computer.

• Before connecting the computer to the USB TO HOST connector, exit from any power-saving mode (such

as suspended, sleep, standby) of the computer.

• Before turning on the power to the instrument, connect the computer to the USB TO HOST connector.

• Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB

cable to/from the USB TO HOST connector.

- Quit any open applications.

- Make sure that data is not being transmitted from the instrument. (Data is transmitted only by playing

notes on the keyboard or playing back a song.)

• While a USB device is connected to the instrument, you should wait for six seconds or more between these

operations: (1) when turning the power of the instrument off then on again, or (2) when alternately

connecting/disconnecting the USB cable.

MOX6/MOX8 Editor

Installing the Software

NOTICE

MOX6/MOX8 Editor Installation Guide 4

The system requirements below may differ slightly depending on the particular operating system.

Windows

Mac

n Keep in mind that the software is often updated and the system requirements are subject to change. You can check the latest version

information of each program and its system requirements at the following website

http://www.yamahasynth.com/downloads/

The system requirements may differ slightly depending on the particular computer.

When using the MOX6/MOX8 Editor as a plug-in within a DAW program, refer to the minimum requirements for the DAW software you

are using as well as the minimum requirements for the MOX6/MOX8 Editor given above.

Minimum System Requirements

Windows 7/Windows Vista SP1/Windows XP SP3 Home Edition/Windows XP SP3 Professional

Computer

Intel Pentium 1.4 GHz or higher

Available Memory

Windows Vista, Windows 7: 1GB or more

Windows XP: 512MB or more

Hard Disk

200 MB or more

Display

1024 x 768, high color (16 bit) or higher

Other

Studio Manager 2.3.1 or later

Version 5.5 or later Cubase 5/Cubase Studio 5, and version 5.1.1 or later Cubase Essential 5/

Cubase AI 5.

Mac OS X 10.5, 10.6

Computer

Power PC G4 1GHz or higher CPU / Intel CPU

Available Memory

512 MB or more

Hard Disk

200 MB or more

Display

1024 x 768, high color (16 bit) or higher

Other

Studio Manager 2.3.3 or later

Version 5.5 or later Cubase 5/Cubase Studio 5, and version 5.1.1 or later Cubase Essential 5/

Cubase AI 5.

MOX6/MOX8 Editor Installation Guide 5

You’ll need to install the following software programs. Follow the appropriate instructions below corresponding to

the software you’re using.

• Yamaha Steinberg USB Driver version 1.2.0 or later

•Studio Manager

• MOX6/MOX8 Editor

Driver Installation

To operate your MOX6/MOX8 from your computer via a USB cable, you’ll need to install the Yamaha Steinberg USB

Driver. The Yamaha Steinberg USB Driver is also necessary when using a USB connection to transfer MIDI data

back and forth between your computer’s DAW and the MOX6/MOX8.

n MOX6/MOX8 Editor cannot be used over a MIDI connection.

Software Installation

Make sure to check the following website for installation and up-to-date news on the driver.

http://www.yamahasynth.com/downloads/

DAW

USB cable

Driver

Computer

MOX6/MOX8

MOX6/MOX8 Editor Installation Guide 6

Studio Manager Installation

Studio Manager is a cross-platform application that enables you to use multiple Editor programs for remotely

controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.

For specific instructions on using the software, refer to the PDF manual from the [HELP] menu in the Studio

Manager and each Editor.

MOX6/MOX8 Editor Installation

Follow the instructions below to install the MOX6/MOX8 Editor programs.

Windows

1 After the downloaded compressed file is properly extracted, double-click the “Install

MOX6_MOX8 Editor.exe” file.

The MOX6/MOX8 Editor setup dialog appears.

n Make sure to log on to the “Administrator” account before installing MOX6/MOX8 Editor.

n If the “User Account Control” window appears, click [Continue] or [Yes].

2 Follow the on-screen instructions to install the software.

Mac

1 After the downloaded compressed file is properly extracted, double-click the “Install

MOX6_MOX8 Editor.mpkg” file.

The MOX6/MOX8 Editor setup dialog appears.

2 Follow the on-screen instructions to install the software.

When the MOX6/MOX8 Editor and the other necessary software is installed, you can start the MOX6/MOX8 Editor.

You’ll need to start the MOX6/MOX8 Editor from the Studio Manager. For details about starting and setting up

Studio Manager, refer to the “Getting Started” on page 7.

To remove the installed editors from Windows:

n The button names or menus may differ depending on the computer OS.

When using Windows Vista / 7

Select [Start]  [Control Panel]  [Programs and Features] or [Uninstall a program], then select the application to

be remove and click [Uninstall/Change].

Follow the on-screen instructions to unistall the application.

If the “User Account Control” window appears, click [Continue] or [Yes].

When using Windows XP

Select [START]  [Control Panel]  [Add/Remove Programs]  [Install/Uninstall], then select the application to be

removed and click [Add/Remove…].

Follow the on-screen instructions to uninstall the application.

You can download the latest version of Studio Manager at the following website. For specific installation instructions, refer to

the installation guide included in the downloaded file.

http://www.yamahasynth.com/downloads/

Windows Software Uninstall (removing the installed application)

MOX6/MOX8 Editor Installation Guide 7

Studio Manager is a cross-platform application that enables you use multiple Editor programs for remotely

controlling Yamaha hardware from your computer, and allows you to save the Editor settings for instant recall.

You can run Studio Manager as a stand-alone application, or as a plug-in within DAW (digital audio workstation)/

sequencer applications that are compatible with Studio Connections, such as Cubase. In either case, the basic

functionality is the same. For the latest information on compatible DAW applications, refer to the following website.

http://www.studioconnections.org/

The settings of each editor can be saved and recalled together from Studio Manager or the DAW application. In

other words, you can change the settings of your entire system in a single operation by recalling the settings for

multiple devices from Studio Manager or your DAW application. This capability is referred to as “Recall.”

When you want to save setting files, you can do this from Studio Manager to recall multiple devices at once, or from

an individual Editor to recall only a specific device. When you save your settings in your DAW application, the

Studio Manager settings will also be saved together with the DAW application file, and can also be recalled in the

same way.

Getting Started

MOX6/MOX8

MOTIF XF6/7/8

MOTIF-RACK XS

Open an editor from

Studio Manager

MOTIF XF Editor application

MO6/MO8 Editor application

MOTIF-RACK XS Editor application

Studio Manager

Start up Studio

Manager in

stand-alone

form

Open from a

compatible DAW

application

Synchronize

MOX6/MOX8 Editor Installation Guide 8

Starting and setting up Studio Manager

You’ll need to perform the following setup in order to use the editors in Studio Manager.

1 Start up Studio Manager.

When starting from a DAW compatible with Studio Connections:

For details, refer to your DAW owner’s manual.

The following procedure applies to Cubase 5.

From Cubase 5’s [Device] menu, choose [Studio Manager] to open the Studio Manager window.

When starting as a stand-alone application:

Windows: Click the [Start] button, place your mouse cursor over [Programs (All Programs)]  [Yamaha Studio

Manager], then click [Studio Manager].

Mac: Open folders in the order of “Applications”  “YAMAHA”  “StudioManager,” and double-click “SM2.”

2 If the MOX6/MOX8 Editor icon isn’t displayed on the workspace of the Studio Manager window,

add the MOX6/MOX8 Editor to the Studio Manager workspace.

Select [File] menu  [Setup]  “Modify Workspace” ([SM2]  [Preference]  “Modify Workspace” for Mac),

then select “MOX6/MOX8” in the “Device Editor” of the “Add Device” and click [Add ]. Make sure that “MOX6/

MOX8” is listed in the “Workspace” column, then click [OK].

n If the MOX6/MOX8 Editor is installed with the box next to “Add the Editor to the Studio Manager Workspace” checkmarked, the

MOX6/MOX8 Editor icon is automatically added to the workspace of the Studio Manager window when Studio Manager is started.

3 Set the MIDI Ports.

When starting Studio Manager as a plug-in of the DAW application:

Set the MIDI Ports on the DAW application. For details, refer to the manual of the DAW application.

When starting Studio Manager as a stand-alone application:

Set the MIDI Ports by calling up the MIDI Ports window via [MIDI Ports]/[MIDI Settings] as following.

[File]  [Setup]  [MIDI Ports]/[MIDI Settings]

(In case of Mac [SM2]  [Preference]  [MIDI Ports]/[MIDI Settings])

Enter checkmarks to the boxes of Ports 1 and 4 for the MOX6/MOX8 for both the Input Ports and the Output

Ports.

MOX6/MOX8 Editor Installation Guide 9

Start up the MOX6/MOX8 Editorr.

In the Studio Manager window, double-click the icon for the MOX6/MOX8 Editor.

Studio Manager window

5 Set up the MOX6/MOX8 Editor.

For details, refer to the PDF manual, found in the [Help] menu on the MOX6/MOX8 Editor.

6 Synchronize the MOX6/MOX8 Editor with your mixing console.

For details, refer to the PDF manual, found in the [Help] menu on each editor.

Audio Integration

Since the MOX6/MOX8 Editor is compatible with Audio Integration, you can also start the Editor within the DAW as easily as

you would with any plug-in software synthesizer.

For details about Audio Integration, visit our web site at:

http://www.studioconnections.org/

MOX6/MOX8 Editor Installation Guide 10

When starting the MOX6/MOX8 Editor after the installation and controlling the MOX6/MOX8 from

your computer via the USB cable, the MOX6/MOX8 does not operate correctly.

• Did you install the latest driver? ..................................................................................................................... page 5

• Is the USB cable used to connect the MOX6/MOX8 to your computer connected correctly?

....................................................................................................................................................... MOX6/MOX8 Owner’s Manual

• If your computer has automatically activated any power-saving mode (such as suspended, sleep, standby) when

you make the USB connection, the computer may “freeze,” or the driver may stop working. When using a USB

cable, disable any power-saving mode on the computer.

• Confirm whether or not a proper USB cable is used.

If the USB cable is broken or damaged, have the USB cable replaced with a known working one.

• Do not use a USB hub for connecting multiple USB devices.

Screen redrawing is slow or stopped.

• Does your computer satisfy the system requirements?.................................................................................. page 4

• Is any other application or device driver running?

Quit the device driver or any unnecessary applications before operating the MOX6/MOX8 Editor.

Troubleshooting

U.R.G., Digital Musical Instruments Division