Yamaha PSR-I300 Omistajan opas

1

Setting UpReferenceAppendix

Before using the instrument, be sure to read

“PRECAUTIONS” on pages 5-7.

3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your author-

ity, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “ B” digital devices. Compliance with these requirements

provides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment gen-

erates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

- Relocate either this product or the device that is being

affected by the interference.

- Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

- In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you cannot locate the appropriate

retailer, please contact Yamaha Corporation of America, 6600

Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

(529-M04 FCC class B YCA 02)

COMPLIANCE INFORMATION STATEMENT

(Supplier’s declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Avenue, Buena Park, CA. 90620, U.S.A.

Telephone : 714-522-9011

Type of Equipment : Digital Keyboard

Model Name : PSR-I300

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that may

cause undesired operation.

(529-M02 FCC sdoc YCA 02)

(1003-M06 plate bottom en 01)

The model number, serial number, power require-

ments, etc., may be found on or near the name

plate, which is at the bottom of the unit. You should

note this serial number in the space provided below

and retain this manual as a permanent record of

your purchase to aid identification in the event of

theft.

Model No.

Serial No.

PSR-I300 Owner’s Manual

4

For the AC adaptor

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the liter-

ature accompanying the product.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

dance with the manufacturer's instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tri-

pod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

(502-M01 UL 60065-1 en 01)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

(604-M02 SG adaptor 01)

For Singapore

Users are only allowed to use EN 50075 detachable and interchangeable 2-pin plugs or BS 1363-3 or SS

145-3 detachable and interchangeable 3-pin plugs that are approved and suitable to use in Singapore.

PSR-I300 Owner’s Manual 5

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Especially in the case of children, a guardian should provide guidance on how to

properly use and handle the product before actual use.

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or

even death from electrical shock, short-circuiting, damages, fire or other hazards. These

precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage the

cord, or place heavy objects on it.

• Do not touch the product or the power plug during an electrical

storm.

• Use only the correct voltage specified for the product. The

required voltage is printed on the name plate of the product.

• Use only the supplied or the specified AC adaptor (page 91). Do

not use the AC adaptor for other devices.

• Check the power plug periodically and remove any dirt or dust

which may have accumulated on it.

• Insert the power plug firmly all the way into the AC outlet. Using

the product when it is not plugged in sufficiently can cause dust

to accumulate on the plug, possibly resulting in fire or skin burns.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug

from the outlet. Even when the power switch is turned off, as long

as the power cord is not unplugged from the wall AC outlet, the

product will not be disconnected from the power source.

• Do not connect the product to an electrical outlet using a multi-

plug outlet extender. Doing so can result in lower sound quality,

or possibly cause overheating in the outlet.

• When disconnecting the power plug, always hold the plug itself

and not the cord. Pulling by the cord can damage it and cause

electric shocks or a fire.

• If not using the product for long periods of time, be sure to pull

the power plug from the AC outlet.

• This product contains no user-serviceable parts. Do not attempt

to disassemble the internal parts or modify them in any way.

• Do not expose the product to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases, bottles

or glasses) containing liquids which might spill into any openings

or places where water may drop. A liquid such as water getting into

the product may cause a fire, electric shocks, or malfunctions.

• Use the AC adaptor indoors only. Do not use in any wet

environments.

• Never insert or remove a power plug with wet hands.

• Do not place any burning items or open flames near the product,

since they may cause a fire.

• Magnetism from this product may affect electro-medical devices,

such as a heart pacemaker implant or defibrillator implant.

- Keep the product away from a heart pacemaker implant or a

defibrillator implant.

• Do not dispose of a battery in a fire.

• Do not expose the battery to conditions of extreme low air

pressure, cold or heat (such as in direct sunlight or a fire) or

excessive dust or humidity. Doing so may result in the battery

bursting, causing a fire or injury.

• Follow the precautions below. Failure to do so might result in

battery fluid leakage. If the contents of the battery gets on your

hands or in your eyes, it can cause blindness, chemical burns,

and damage of the product.

- Use the specified battery type (page 91) only.

- Do not use new batteries together with old ones.

- Do not mix battery types.

- Always make sure all batteries are inserted in conformity with

the +/- polarity markings.

- Do not disassemble a battery.

- When the batteries run out, or if the product is not to be used

for a long time, remove the batteries from the product.

- Do not attempt to recharge batteries that are not designed to be

charged.

Power supply

Do not disassemble

Water warning

Fire warning

Handling

Batteries

DMI-11 1/3

PSR-I300 Owner’s Manual

6

• If the batteries do leak, avoid contact with the leaked fluid. If the

battery fluid should come in contact with your eyes, mouth, or

skin, wash immediately with water and consult a doctor. Battery

fluid is corrosive and may possibly cause loss of sight or

chemical burns.

• When using rechargeable batteries, follow the instructions that

came with the batteries. Use only the specified charger device and

within the specified charging temperature range when charging.

Charging with an unspecified charger or at a temperature outside

the range may cause leakage, overheating, explosion, or

malfunction.

• Keep batteries away from children. A child could accidentally

swallow a battery. Failure to observe this may also cause

inflammation due to battery fluid leaks.

• Do not put batteries in a pocket or bag, or carry or store them

together with pieces of metal. Batteries kept in such condition

could short, burst, or leak, causing a fire or injury.

• If any of the following problems occur, immediately turn off the

power switch and disconnect the power plug from the outlet. If

you are using batteries, remove all batteries from the product.

Finally have the device inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped into the product.

- There is a sudden loss of sound during use of the product.

- Cracks or other visible damage appear on the product.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you

or others, or damage to the product or other property. These precautions include, but are not

limited to, the following:

• Do not place the product in an unstable position or a location with

excessive vibration, where it might accidentally fall over and

cause injury.

• Before moving the product, remove all connected cables, to

prevent damage to the cables or injury to anyone who might trip

over them.

• Use only the stand specified for the product. When attaching it,

use the provided screws only. Failure to do so could cause

damage to the internal components or result in the product falling

over.

• Before connecting the product to other electronic components,

turn off the power for all components. Before turning the power on

or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

product to set the desired listening level.

• Do not insert your finger or hand in any gaps on the product.

• Do not insert foreign materials such as metal or paper into any

openings or gaps of the product. Failure to observe this may

cause a fire, electric shocks, or malfunctions.

• Do not rest your weight on, or place heavy objects on the product,

and do not use excessive force on the buttons, switches or

connectors.

• Do not use the product or headphones for a long period of time at

a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

• Remove the power plug from the AC outlet before cleaning the

unit. Failure to observe this may cause electric shocks.

Always turn the power off when the product is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the product at the minimum level.

When you are not using the product for a long time, make sure you unplug the power cord from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

If you notice any abnormality

Location

Connections

Handling

Yamaha cannot be held responsible for damage caused by improper use or modifications to the product, or data that is lost or destroyed.

DMI-11 2/3

PSR-I300 Owner’s Manual 7

NOTICE

To avoid the possibility of malfunction/ damage

to the product, damage to data, or damage to

other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric

devices. Otherwise, the instrument, TV, or radio may

generate noise.

• When you use the instrument along with an app on your

smart device, such as a smartphone or tablet, we

recommend that you enable “Airplane Mode” on the

device to avoid noise caused by communication.

• Depending on the condition of surrounding radio waves,

the instrument may possiblymalfunction.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to

prevent the possibility of disfiguration, damage to the

internal components or unstable operation. (Verified

operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the instrument.

• Do not press the LCD screen with your finger because it

is a sensitive, precision-made part. Doing so might cause

an appearance abnormality, such as a stripe on the LCD,

although this abnormality should disappear again within

a short time.

 Maintenance

• When cleaning the instrument, use a soft and dry/slightly

damp cloth. Do not use paint thinners, solvents, alcohol,

cleaning fluids, or chemical-impregnated wiping cloths.

 Saving data

• Some of the data of this instrument (page 53) are retained

when the power is turned off. However, the saved data

may be lost due to some failure, an operation mistake,

etc. Save your important data onto an external device

such as a computer (page 52).

Information

 About copyrights

• The copyright of the “content”*1 installed in this product

belongs to Yamaha Corporation or its copyright holder.

Except as permitted by copyright laws and other relevant

laws, such as copying for personal use, it is prohibited to

“reproduce or divert”*2 without the permission of the

copyright holder. When using the content, consult with a

copyright expert.

• If you create music or perform with the contents through

the original use of the product, and then record and

distribute them, the permission of Yamaha Corporation is

not required regardless of whether the distribution

method is paid or free of charge.

*1: The word “content” includes a computer program,

audio data, Accompaniment Style data, MIDI data,

waveform data, voice recording data, music score,

and score data, etc.

*2: The phrase “reproduce or divert” includes taking out

the content itself in this product, or recording and

distributing it without changes in a similar manner.

 About functions/data bundled with the

instrument

• Some of the preset Songs have been edited for length or

arrangement, and may not be exactly the same as the

original.

 About the appearance of this product

• This product may appear to have lines or scratches on the

surface.The apparent lines or scratches are called “weld

lines.”They occur during the process of modeling the

case and do not affect thefunctionality of the product.

 About this manual

• The illustrations and LCD screens as shown in this

manual are for instructional purposes only.

• iPhone, iPad are trademarks of Apple Inc., registered in

the U.S. and other countries.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

 About this manual

• When disposing of this product, please contact the

appropriate local authorities.

• Make sure to discard used batteries according to local

regulations.

DMI-11 3/3

PSR-I300 Owner’s Manual

8

About the Manuals

In addition to this Owner’s Manual, the following Online materials (PDF files) are available.

Drum Kit List

This contains detailed information of the Drum Kit Voices (Voice Nos. 260–279; page 72). When you

select these Voices, various drum, percussion and SFX sounds listed here are assigned to each key.

MIDI Reference

This contains MIDI-related information, such as the MIDI Implementation Chart.

Computer-related Operations

This contains instructions about computer-related functions.

Smart Device Connection Manual

This explains how to connect the instrument to smart devices, such as smartphones, tablet

devices, etc.

To obtain these manuals, access the Yamaha Downloads page, and then enter the model name for

searching for the desired files.

Yamaha Downloads https://download.yamaha.com/

Song Book (only in English and French)

This contains music scores for the preset Songs (excluding the Demo Songs) of this instrument.

To obtain this Song Book, access the Yamaha website and download it from the product web page.

Yamaha Global Site https://www.yamaha.com

Included Accessories

• Owner’s Manual (this book)

• AC adaptor*

• Music rest

• Online Member Product Registration

* May not be included depending on your particular locale. Check

with your Yamaha dealer.

Formats and functions

GM System Level 1

“GM System Level 1” is an addition to the MIDI

standard which ensures that any GM-compati-

ble music data can be accurately played by any

GM-compatible tone generator, regardless of

manufacturer. The GM mark is affixed to all

software and hardware products that support

GM System Level.

XGlite

As its name implies, “XGlite” is a simplified ver-

sion of Yamaha’s high-quality XG tone genera-

tion format. Naturally, you can play back any

XG song data using an XGlite tone generator.

However, keep in mind that some songs may

play back differently compared to the original

data, due to the reduced set of control parame-

ters and effects.

Style File Format (SFF)

The Style File Format combines all of

Yamaha’s auto accompaniment know-how

into a single unified format.

USB

USB is an abbreviation for Universal Serial

Bus. It is a serial interface for connecting a

computer with peripheral devices. It allows

“hot swapping” (connecting peripheral

devices while the power to the computer is

on).

Touch Response

The exceptionally natural Touch Response

feature gives you maximum expressive con-

trol over the level of the Voices.

• For a general overview of MIDI and how you can effectively use it, search for “MIDI Basics” (only in English, Ger-

man, French and Spanish) on the website above.

NOTE

PSR-I300 Owner’s Manual 9

Setting UpAppendix Reference

About the Manuals.................................................... 8

Included Accessories................................................ 8

Formats and functions .............................................. 8

Setting Up

Panel Controls and Terminals 10

Setting Up 12

Power Requirements .............................................. 12

Turning the Power On ............................................ 13

Setting the Auto Power Off function ....................... 13

Adjusting the Master Volume.................................. 14

Connecting Headphones or External Speakers ..... 14

Using a Pedal ......................................................... 14

Using the Music Rest.............................................. 14

Display Items and Basic Operations 15

Display Items.......................................................... 15

Basic Operations .................................................... 15

Reference

Playing a Variety of Instrument Voices 16

Selecting a Main Voice........................................... 16

Playing the “Harmonium/Piano”.............................. 16

Using the Metronome ............................................. 16

Layering a Dual Voice ............................................ 17

Playing a Split Voice in the Left-hand Area ............ 17

Changing the Touch Response of the Keyboard.... 18

Pitch Controls—the [PITCH BEND] Wheel............. 18

Applying Effects to the Sound ................................ 19

Adding Harmony or Arpeggio ................................. 21

Playing the keyboard with two persons (Duo mode)

23

Playing Rhythm and Accompaniment (Style)

24

Fingering Type........................................................ 24

Setting the Fingering Type ..................................... 24

Setting the Smart Chord Key.................................. 24

Playing Styles ......................................................... 25

Style Variations....................................................... 26

Chord Types for Style Playback ............................. 27

Chords Heard When Smart Chord is Selected....... 28

Looking Up Chords Using the Chord Dictionary..... 29

Using the Music Database...................................... 30

Registering a Style File........................................... 30

Changing the Tempo .............................................. 31

Playing with Riyaz Lite 32

Playing Songs33

Listening to a Demo Song ...................................... 33

Selecting and Playing Back a Song........................ 33

BGM Playback........................................................ 34

Song Fast Forward, Fast Reverse, and Pause ...... 34

Changing the Melody Voice.................................... 34

A-B Repeat ............................................................. 35

Turning Each Part On/Off....................................... 35

Playing Songs Loaded From a Computer .............. 35

Using the Song Lesson Feature 36

Keys To Success ....................................................37

Phrase Repeat ........................................................39

Listening, Timing and Waiting.................................40

Learning How to Use “Touch” Control (Touch Tutor)

42

Hearing and Experiencing the Sound of

the Chords (Chord Study) 43

Hear and Experience a Sound of a Single Chord ... 43

Hear and Experience Basic Chord Progressions....43

Playing Chords Along with

Chord Progressions of a Song44

Playing Chords in Combination with

“Waiting” of the Lesson Function .......................44

Recording Your Performance 45

Track Structure of a Song .......................................45

Quick Recording .....................................................45

Recording to a Specific Track .................................46

Clearing a User Song..............................................46

Memorizing Your Favorite Panel Settings47

Recalling Panel Settings from the Registration Memory

...47

Memorizing Panel Settings to the Registration Memory

....48

Deleting the Registration Memory...........................48

Disabling Recall of Specific Items (Freeze) ............48

Selecting an EQ Setting for your Favorite Sound

49

Playing a Device with the Built-in Speakers

50

Lowering the Volume of a Melody Part

(Melody Suppressor).......................................... 51

Using with a Computer or Smart Device 52

Connecting to a computer.......................................52

Connecting a Smart Device .................................... 52

Backup and Initialization 53

Backup Parameters ................................................53

Initialization .............................................................53

The Functions 54

Appendix

Troubleshooting.............................................58

Song Book Sample.........................................60

Voice List ........................................................70

Drum Kit List (Indian Kit List)........................76

Drum Kit List (Standard Kit 1) .......................80

Song List .........................................................81

Style/Riyaz List ...............................................82

Music Database List.......................................84

Effect Type List...............................................86

Specifications .................................................90

Index ................................................................92

Contents

Thank you for purchasing this Yamaha Digital Keyboard!

This instrument is loaded with various sounds, preset Songs and many convenient functions—

so that even beginners can enjoy playing it right away.

We recommend that you read this manual carefully so you can fully take advantage of the advanced

and convenient functions of the instrument.

We also recommend that you keep this manual in a safe and handy place for future reference.

PSR-I300 Owner’s Manual

10

Setting Up

Panel Controls and Terminals

Front Panel

Setting Up

q

w

e

r

u

i

o

t

y

!1 !2 !3 !4 !5

!0

!6

!7

!8

@1 @2 @3

!9 @5

@6

@7

@8

@9

C1 C2 C3 C4 C5 C6

@4

@0

Voice List

(page 70)

Song List

(page 81)

Display

(page 15)

Style List

(page 82)

Riyaz

(page 83)

As illustrated, each note of

the keyboard has a specific

note number and name

(e.g., 036/C1), which is

used in making various set-

tings, such as Split Point

(page 25).

Panel Controls and Terminals

PSR-I300 Owner’s Manual 11

Setting Up

q[ ] (Standby/On) switch ....................page 13

w[MASTER VOLUME] dial ......................page 14

e[DEMO] button......................................page 33

r[METRONOME] button.........................page 16

t[TEMPO/TAP] button ............................page 31

yPART

[L] button ..............................................page 40

[R] button ..............................................page 40

y[REC TRACK 2] button.........................page 45

[REC TRACK 1] button.........................page 45

u[KEYS TO SUCCESS] button...............page 37

i[PHRASE REPEAT] button...................page 39

o[1 LISTENING 2 TIMING 3 WAITING] button

...............................................................page 40

!0 [A-B REPEAT] button ...........................page 35

!1 [REW] button ........................................page 34

!2 [FF] button ............................................page 34

!3 [PAUSE] button.....................................page 34

!0 [ACMP ON/OFF] button........................page 25

!1 [INTRO/ENDING/rit.] button.................page 26

!2 [MAIN/AUTO FILL] button ....................page 26

!3 [SYNC START] button ..........................page 25

!0 [TANPURA ON/OFF] button.................page 32

!1 [SECTION A] button .............................page 32

!2 [SECTION B] button .............................page 32

!3 [SECTION C] button .............................page 32

!4 [START/STOP] button...........................page 33

!5 [REC] button .........................................page 45

!6 [VOICE] button......................................page 16

!7 [SONG] button ......................................page 33

!8 [STYLE/RIYAZ] button..........................page 25

!9

Number buttons [0]–[9], [+/YES], [-/NO]

....page 15

@0 [HARMONIUM/PIANO] button .............page 16

@1 [DSP] button .........................................page 19

@2 [ARTICULATION] button ......................page 19

@3 [REGIST MEMORY] button ..................page 47

@4 [FUNCTION] button ..............................page 54

@5 [MUSIC DATABASE] button .................page 30

@6 [DUAL] button.......................................page 17

@7 [SPLIT] button.......................................page 17

@8 [HARMONY/ARPEGGIO] button..........page 21

@9 [PITCH BEND] wheel............................page 18

#0 [SUSTAIN] jack .....................................page 14

#1 [PHONES/OUTPUT] jack......................page 14

#2 [AUX IN] jack.........................................page 50

#3 [USB TO HOST] terminal* ....................page 52

* For connecting to a computer. For details, refer to “Com-

puter-related Operations” (page 8) on the website. When

connecting, use an AB type USB cable of less than 3

meters. USB 3.0 cables cannot be used.

#4 DC IN jack .............................................page 12

In the Lesson mode

In the Recording mode

In the Song mode

In the Style mode

In the Riyaz mode

Panel Setup (Panel Settings)

By using the controls on the panel, you can make various

settings as described here. These settings of the instru-

ment are together referred to as “panel setup” or “panel

settings” in this manual.

The “Press and hold” Symbol

Buttons having this indication can be used to call

up an alternate function when the relevant button

is pressed and held. Hold down this button until

the function is called up.

#1 #2 #3

#4

#0

Rear Panel

PSR-I300 Owner’s Manual

12

Setting Up

Power Requirements

Although the instrument will run either from an AC

adaptor or batteries, Yamaha recommends use of an

AC adaptor whenever possible. An AC adaptor is

more environmentally friendly than batteries and

does not deplete resources.

Using an AC Adaptor

Connect the AC adaptor in the order shown in the

illustration.

Using Batteries

This instrument requires six “AA” size, Alkaline (LR6)/

Manganese (R6) batteries, or rechargeable nickel-

metal hydride batteries (rechargeable Ni-MH batter-

ies). The Alkaline batteries or rechargeable Ni-MH

batteries are recommended for this instrument, since

other types may result in poorer battery performance.

1Make sure that the power of the instrument is off.

2Open the battery compartment cover located on

the instrument’s bottom panel.

3Insert the six new batteries, being careful to follow

the polarity markings on the inside of the com-

partment.

4Replace the compartment cover, making sure that

it locks firmly in place.

Make sure to set the battery type correctly (page 13).

• Use the specified AC adaptor (page 91) only. Using the

wrong AC adaptor can result in damage to the instrument

or overheating.

• When using the AC adaptor with a removable plug, make

sure to keep the plug attached to the AC adaptor. Using the

plug alone can cause electric shock or fire.

• If the plug is accidentally removed from the AC adaptor,

slide it back in until it clicks into place, taking care to

avoid touching any internal metal parts. To avoid electric

shock, short circuit or damage, also be careful that there

is no dust between the AC adaptor and plug.

• When setting up the product, make sure that the AC outlet

you are using is easily accessible. If some trouble or mal-

function occurs, immediately turn the power off and dis-

connect the plug from the outlet.

• Follow the order shown above in reverse when disconnecting

the AC adaptor.

2

1DC IN jack

(page 11)

AC outlet

AC

adaptor

WARNING

Plug

The shape of the plug differs depending on

your area.

Slide the plug as

indicated.

CAUTION

NOTE

• When the batteries run out, or if the instrument is not to be

used for a long time, remove the batteries from the instru-

ment.

• Connecting or disconnecting the AC adaptor with batter-

ies installed may turn the power off, resulting in loss of

data being recorded or transferred at the time.

• When battery power becomes too low for proper opera-

tion, the volume may be reduced, the sound may be dis-

torted, and other problems may occur. When this happens,

make sure to replace all batteries with new ones or already

recharged ones.

WARNING

NOTICE

Setting Up

PSR-I300 Owner’s Manual 13

Setting Up

Setting the battery type

Depending on the battery to be installed, you may

need to change the battery type setting, although

“Alkaline (and manganese)” is set by default. After

installing new batteries, call up Function number 063

(page 57), and then set the Battery Type (recharge-

able or not).

Turning the Power On

1Turn down the [MASTER VOLUME] dial to “MIN.”

2Press the [ ] (Standby/On) switch to turn the

power on.

The Voice name appears on the display. Adjust

the volume as desired while playing the key-

board.

3Press and hold the [ ] (Standby/On) switch for

about a second to set the instrument to standby

mode.

Setting the Auto Power Off

function

To prevent unnecessary power consumption, this

instrument turns off automatically if not operated for

30 minutes by default. This non-operation time can

be changed as desired.

To change the non-operation time

which enables Auto Power Off

Press the [FUNCTION] button several times until

“AutoOff” (Function 062; page 57) appears, and then

use the [+/YES] or [-/NO] button to select the desired

value.

Settings: OFF, 5, 10, 15, 30, 60, 120 (minutes)

Default value: 30 (minutes)



To cancel Auto Power Off when turning

on the instrument

Turn the power on while holding down the lowest key

on the keyboard. A message “oFF AutoOff” appears

briefly, then the instrument starts up with the Auto

Power Off function disabled.

• This instrument cannot charge the batteries. Use only the

specified charger device when charging.

• Power will be automatically drawn from the AC adaptor if an

AC adaptor is connected while batteries are installed in the

instrument.

• Failure to set the battery type may shorten the amount of

the battery life. Make sure to set the battery type correctly.

• Even when the [ ] (Standby/On) switch is in standby sta-

tus, electricity is still flowing to the product at the mini-

mum level. Remove the electric plug from the outlet when

the instrument is not to be used for extended periods of

time, or during electrical storms.

• Press only the [ ] (Standby/On) switch when turning the

power on. Any other operations such as pressing the pedal

are not allowed. Doing so may cause the instrument to

malfunction.

NOTE

NOTICE

CAUTION

NOTICE

• Depending on the instrument status, the power may not

turn off automatically, even after the elapse of the specified

period of time. Always turn off the power manually when

the instrument is not in use.

• When the instrument is not operated for a specified time

while connected to an external device such as an amplifier,

speaker or computer, make sure to turn off all connected

devices including the instrument, in order to protect the

devices from possible damage from power turning off

automatically. Alternately, if you want to avoid doing this,

simply disable the Auto Power Off function.

• Generally, the data and settings are maintained even when

the power is turned off with the Auto Power Off function. For

details, see page 53.

The lowest key

NOTICE

NOTE

Setting Up

PSR-I300 Owner’s Manual

14

Setting Up

Adjusting the Master Volume

To adjust the volume of the entire keyboard sound,

use the [MASTER VOLUME] dial while playing the

keyboard.

Connecting Headphones or

External Speakers

Connect a pair of headphones to the [PHONES/

OUTPUT] jack. This jack also functions as an exter-

nal output. By connecting to a keyboard amplifier,

recorder, or other audio device, you can output the

audio signal of this instrument to that external device.

The speakers of this instrument are automatically

shut off when a plug is inserted into this jack.

Using a Pedal

By using a pedal, you can control one of four func-

tions in real time as you play: Sustain, Articulation

(page 20), Arpeggio (page 22) and Sostenuto (page

56). Make sure the footswitch (FC5 or FC4A; sold

separately) plugged into the [SUSTAIN] jack. By

default, Sustain is assigned, so that the sound can

be heard for a long time even if you take your finger

off the keyboard while pressing the foot switch, like a

damper pedal on a piano. To use a function other

than Sustain, use the function settings (Function 031;

page 56).

Using the Music Rest

Insert the music rest into the slots as shown.

• Do not use the instrument for a long period of time at a

high or uncomfortable volume level, since this can cause

permanent hearing loss.

• Do not use the instrument or headphones for a long period

of time at a high or uncomfortable volume level, since this

can cause permanent hearing loss.

• Before connecting an external device via the [PHONES/

OUTPUT] jack, turn off both the device and the instrument.

After connecting, set all volume levels to minimum, and

then turn on/off both the device and the instrument. When

turning on, turn on the instrument first, and then the

device; when turning off, turn off the device and then the

instrument. Otherwise, damage to the instrument and

device or electrical shock may occur.

• When the [PHONES/OUTPUT] jack is connected, set the

Master EQ (page 49) to “3 Headphone.”

CAUTION

Standard stereo

phone plug

CAUTION

NOTE

• Plug or unplug the footswitch while the power is off. Also, do

not press the footswitch when turning the power on. Doing so

changes the polarity of the footswitch, resulting in reversed

operation.

• The sustain function does not affect Split Voices (page 17),

Style (automatic accompaniment; page 24) and Riyaz (page

32).

NOTE

PSR-I300 Owner’s Manual 15

Setting Up

Display Items and Basic Operations

Display Items

Basic Operations

Number buttons

Use the Number buttons to directly enter an item or

value. For numbers that start with one or two zeroes,

the first zeroes can be omitted.

[-/NO] and [+/YES] buttons

Press the [+/YES] button briefly to increase the value by 1,

or press the [-/NO] button briefly to decrease the value by 1.

Press and hold either button to continuously increase or

decrease the value in the corresponding direction.

003

Harmnum1

001

Voice/Song/Style

This area indicates the Lesson

related status.

Keys To Success

(page 37)

Phrase Repeat (page 39)

Chord Progression (page 44)

Indicates the Passing Status (page

38) of the Keys To Success lesson.

Lesson Indication

Harmony

(

page 21

)

Arpeggio

(

page 21

)

Dual (

page 17

)

Split (

page 17

)

DSP (

page 19

)

Duo (

page 23

)

Articulation (page 19)

Function status

Indicates the chord which is played in the Auto

Accompaniment range (page 25) of the keyboard, or

specified via Song playback.

Normally indicates the current measure number of the

current Style, Riyaz or Song. When the [FUNCTION] button

(page 54) is in use, this indicates the Function number.

Indicates the current beat of playback.

Indicates notes you are currently playing, or notes specified via the Song

Lesson function or Chord Dictionary function.

Chord

Function or Measure

Beat

Keyboard Display

027

003

C3

Indicates the on/off status of Song

playback or target track of Song

recording (pages 35, 46).

Lit: Track contains data

Unlit: Track is muted or contains no data

Flashing: Track is selected as recording track

Appears when the A-B Repeat

function is active. (page 35)

Appears when the Auto

Accompaniment function is on.

(page 25)

Song Track status

A-B Repeat

Auto Accompaniment

(page 47)

Registration

Memory

Touch Response (page 18)

Strength Meter

is a meter that lights up

according to the strength with

which you play the keyboard.

(pages 18, 42)

represents the target

strength when practicing with

songs in the “Touch Tutor”

category. (page 42)

Touch Indication

Voice selection mode

Song mode

Style/Riyaz mode

is always shown while either or

is shown.

appears only when the settings of the corresponding

function can be edited.

Press number but-

tons [0], [0], [3], or

simply press [3].

Example: Selecting Voice 003,

Harmnum3.

Press briefly to

increase.

Press briefly to

decrease.

PSR-I300 Owner’s Manual

16

Reference

Playing a Variety of Instrument Voices

In addition to piano, organ, and other “conventional” keyboard instruments, this instru-

ment has a large range of Voices that includes guitar, bass, strings, sax, trumpet, drums

and percussion, and even sound effects—giving you a wide variety of musical sounds.

1Press the [VOICE] button.

The Voice number and name will be shown.

2Use the number buttons [0]–[9], or

[+/YES] and [-/NO] buttons to select the

desired Voice.

Refer to the Voice List on page 70.

3Play the keyboard.

Preset Voice Types

When you want to reset various settings to default

and simply play a Harmonium sound, press the

[HARMONIUM/PIANO] button.

The Voice “001 Harmonium Single” is selected auto-

matically as the Main Voice. When “001 Harmonium

Single” is already selected, “031 Live! Concert Grand

Piano” is selected instead.

The instrument features a built-in metronome (a

device that keeps an accurate tempo), convenient for

practicing.

1Press the [METRONOME] button to start

the metronome.

2Press the [METRONOME] button again to

stop the metronome.

To change the tempo:

Press the [TEMPO/TAP] button to call up the Tempo

value, and then use the number buttons [0]–[9], or

[+/YES] and [-/NO] buttons.

Press the [+/YES] and [-/NO] buttons simultaneously

to call up the default tempo value of the current Style,

Riyaz or Song.

To set the Time Signature:

Press and hold the [METRONOME] button to call up

“TimeSigN” (Functions 032; page 56), and then use

the number buttons, or [+/YES] and [-/NO] buttons.

To set the Metronome Volume:

Call up Function number 034 (page 56).

Selecting a Main Voice

• is not displayed alone. It is always displayed

with or . Refer to page 15.

001–030

(Indian Voices) Used for Indian music performance.

001–259 Instrument Voices (including sound effects).

260–279

(Drum Kit)

Various drum and percussion sounds are

assigned to individual keys, from which they can

be played. Details on the instruments and key

assignments of each Drum Kit can be found on

page 72.

280–299 Arpeggios are automatically reproduced by

simply playing the keyboard (page 21).

300–644 XGlite Voices (page 73)

000

One Touch Setting

The One Touch Setting feature automatically

selects the most suitable Voice when you

select a Style, Riyaz or Song (excepting Songs

and Styles input from other devices). Simply

select Voice number “000” to activate this fea-

ture.

Harmnum1

001

Voice name

The Voice shown here

becomes the Main

Voice for the instrument.

Voice number

Always

appears on

the display.

NOTE

Shehnai

004

Select the Voice you want to play

Playing the “Harmonium/Piano”

Using the Metronome

Tempo

090

Current Tempo value

Reference

Playing a Variety of Instrument Voices

PSR-I300 Owner’s Manual 17

Reference

In addition to the Main Voice, you can layer a differ-

ent Voice over the entire keyboard as a “Dual Voice.”

1Press the [DUAL] button to turn Dual on.

2Play the keyboard.

3Press the [DUAL] button again to exit

from Dual.

To select a different Dual Voice:

Although turning on Dual will select a Dual Voice

suitable for the current Main Voice, you can easily

select a different Dual Voice by pressing and holding

the [DUAL] button to call up “D.Voice” (Function 009;

page 55), then using the number buttons [0]–[9], or

[+/YES] and [-/NO] buttons.

By dividing the keyboard into two separate areas,

you can play a different Voice between the left-hand

and right-hand areas.

1Press the [SPLIT] button to turn on Split.

The keyboard is divided into left- and right-hand

areas.

You can play a “Split Voice” in the left-hand area

of the keyboard while playing a Main Voice and

Dual Voice in the right-hand area of the keyboard.

The highest key for the left-hand area is referred

to as the “SplitPnt” (Function 004;

page 54

) which

can be changed from the default F#2 key.

2Play the keyboard.

3Press the [SPLIT] button again to exit

from Split.

To select another Split Voice:

Press and hold the [SPLIT] button to call up “S.Voice”

(Function 013; page 55), and then use the number

buttons [0]–[9], or [+/YES] and [-/NO] buttons.

Layering a Dual Voice

Harmnum1

001

Appears when Dual

is on

Two Voices sound

together.

Playing a Split Voice in the Left-

hand Area

Harmnum1

001

Appears when Split

is on

Split Voice Main Voice and Dual Voice

Split Point default setting: 054 (F#2)

036

(C1)

048

(C2)

060

(C3)

072

(C4)

084

(C5)

096

(C6)

Left-hand area

Right-hand area

Playing a Variety of Instrument Voices

PSR-I300 Owner’s Manual

18

Reference

The keyboard of this instrument is equipped with a

Touch Response feature that lets you dynamically

and expressively control the level of the Voices

according to your playing strength.

1Press the [FUNCTION] button several

times until “TouchRes” (Function 005;

page 54) appears.

After a few seconds, the current Touch Response

appears.

2Use the number buttons [1]–[4], [+/YES],

[-/NO] buttons to select a Touch

Response setting between 1 and 4.

Touch Response

3Play the keyboard.

The strength meter will light according to the

strength with which you play the keyboard.

The [PITCH BEND] wheel can be used to add

smooth pitch variations to notes you play on the key-

board. Roll the wheel upward to raise the pitch, or

downward to lower the pitch.

You can change the amount of pitch bend produced

by the wheel in the Function Settings (page 54, Func-

tion 003).

Changing the Touch Response of

the Keyboard

1Soft

Produces relatively high volume even with

light playing strength. Best for players with a

light touch who want to maintain a consis-

tent, relatively loud volume.

2Medium Produces a fairly “standard” keyboard

response.

3Hard

The keys must be played very strongly to

generate loud volume. This setting is best

for a wide dynamic range and optimum

expressive control of the sound, from pianis-

simo to fortissimo.

4Fixed All notes are produced at the same volume

no matter how hard the keyboard is played.

• When Touch Response is set to “Fixed,” the strength

meter is fixed at medium strength.

TouchRes

005

Medium

2

005

Appears when the Touch

Response is not “Fixed.”

When playing softly:

When playing at

medium strength:

When playing strongly:

NOTE

Pitch Controls

—the [PITCH BEND] Wheel

Playing a Variety of Instrument Voices

PSR-I300 Owner’s Manual 19

Reference

This instrument can apply various Effects to the

instrument’s sound (as described below).

 DSP

This effect applies digital signal processing to the

Main Voice and Song part when a Voice or Song that

includes the DSP setting is selected. The DSP effect

can be turned on/off, and also features various Types

(page 88) which can be selected via the following

procedure.

1Press the [DSP] button to turn on the DSP.

Although the DSP type (page 88) is automatically

determined according to the current Main Voice,

you can select another type.

2Hold down the [DSP] button for a while until the

DSP-related indication appears.

3Use the number buttons [0]–[9], or [+/YES] and

[-/NO] buttons to select the desired type.

4Play the keyboard.

5Press the [DSP] button again to turn off the DSP.

 Articulation

This effect reproduces the sounds of playing meth-

ods that are unique to specific instruments. To enjoy

this effect, select one of the S.Art Lite Voices, indi-

cated by “***” in the Voice List (page 70), and then

play the keyboard while holding down the [ARTICU-

LATION] button.

Examples of the Articulation effect

If you select the following voices, you can realistically

reproduce the specific playing techniques below.

Example 1: Voice number 005 “S.Art Lite Sarangi”

When you play the keyboard while holding down the

[ARTICULATION] button, the attack part sounds with

the pitch bending up.

Example 2: Voice number 012 “S.Art Lite Santoor”

When you press the [ARTICULATION] button, trem-

olo sound is produced.

For Voices other than S.Art Lite Voices

Modulation or Portamento effects are suitably

assigned according to the characteristics of each

Voice. To use the Modulation effect, follow the same

manner as with Articulation. To use the Portamento

effect, follow the instructions below instead. For

details on Portamento, refer to page 20.

1To enable the Portamento effect, press the

[ARTICULATION] button before you start playing

the keyboard.

2To disable the Portamento effect, press the

[ARTICULATION] button again.

Applying Effects to the Sound

• Among the Voices in the keyboard performance, the

DSP effect is applied only to the Main Voice.

• The DSP cannot be turned on during lessons.

NOTE

Harmnum1

001

Appears when

the DSP is on.

DSPType

025

Tremolo

29

025

Current DSP type

Hold for longer

than a second.

Sarangi

005

Appears when the

S.Art Lite Voice is selected

Playing a Variety of Instrument Voices

PSR-I300 Owner’s Manual

20

Reference

Adding the Articulation effect by using a pedal

If you assign the Articulation function to a pedal (foot

switch) with “PdlFunc” (Function 031; page 56), you

can apply the effect by pressing on the pedal.

 Portamento

Portamento is a function that creates a smooth tran-

sition in pitch from the first note played on the key-

board to the next. Using this function effectively

provides even greater expressive nuance to your per-

formance. On this instrument, Portamento is avail-

able on the following Voices.

To enable Portamento, press the [ARTICULATION]

button when one of the Voices above is selected.

 Reverb

Adds room ambience of a club or concert hall to the

sound. Although the best-suited Reverb type is

called up by selecting a Song, Style and Riyaz, you

can select another one via Function number 022

(page 55). You can also set the Reverb depth via

Function number 023 (page 55).

 Chorus

Makes the Voice sound richer, warmer and more

spacious. Although the best-suited Chorus type is

called up by selecting a Song, Style and Riyaz, you

can select another one via Function number 024

(page 55). You can also set the Chorus depth for

Voices only for keyboard performance via Function

numbers 008 (page 54), 012, 016 (page 55).

 Sustain

By turning on the Sustain parameter of Function num-

ber 026 (page 55), you can add a fixed, automatic

sustain to the Main/Dual Voices played on the key-

board. Or, you can produce a natural sustain as

desired with the footswitch (sold separately; page 14).

• The Articulation effect is applied only to the Main Voice.

• S.Art Lite Voices sound differently depending on the velocity,

etc.

006 S!Srangi

007 Pungi

008 S!Bansri

011 Sarod

016 IndBanjo

017 Mandolin

020 Rabab

154 Trombone

164 80sBrass

167 TechBras

168 SynBrass

171 SquareLd

172 Saw.Lead

174 UndrHeim

175 PortTone

176 Analogn1

177 Fargo 1

178 Analogn2

179 Fargo 2

181 Funky Ld

202 Timpani

214 Er Hu

NOTE

• Even if you turn on Sustain, there are some Voices to which

sustain is not applied.

NOTE

Sivu latautuu ...

Yamaha PSR-I300 Omistajan opas

Yamaha PSR-I300 Omistajan opas

muilla kielillä