Yamaha RX-397 Omistajan opas

Tyyppi
Omistajan opas
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©
2005 All rights reserved.
RX-397
Printed in Malaysia WG05100
RX-397
Stereo Receiver
Récepteur stéréo
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
G
01EN_RX-397_GB-cv.fm Page 1 Thursday, August 25, 2005 1:50 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
i
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any damage
resulting from use of this unit with a voltage other than
specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
18 Before moving this unit, press STANDBY/ON to set this unit
to the standby mode, and disconnect the AC power plug from
the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC main supply. Voltages are:
General model.............AC 110/120/220/230–240 V, 50/60 Hz
Asia model ................................AC 220/230–240 V, 50/60 Hz
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off by STANDBY/ON. This
state is called the standby mode. In this state, this unit
is designed to consume a very small quantity of power.
1
PREPARATIONINTRODUCTION
OPERATION
ADDITIONAL
INFORMATION
English
FEATURES............................................................. 2
SUPPLIED ACCESSORIES ................................. 2
CONTROLS AND FUNCTIONS ......................... 3
Front panel ................................................................. 3
Front panel display .................................................... 5
Rear panel .................................................................. 6
Remote control........................................................... 7
Installing batteries in the remote control ................... 8
Using the remote control ........................................... 8
CONNECTIONS .................................................... 9
Connecting speakers ................................................ 10
Connecting the AM and FM antennas ..................... 11
Connecting the power supply cord .......................... 13
Turning on and off this unit..................................... 14
PLAYING AND RECORDING .......................... 15
Playing a source....................................................... 15
Adjusting the tonal quality....................................... 16
Recording a source .................................................. 17
Using the sleep timer ............................................... 18
Muting the sound output.......................................... 19
FM/AM TUNING ................................................. 20
Automatic tuning ..................................................... 20
Manual tuning.......................................................... 21
Automatic preset tuning........................................... 21
Manual preset tuning ............................................... 23
Selecting preset stations........................................... 24
Exchanging preset stations ...................................... 24
RADIO DATA SYSTEM (EUROPE MODEL
ONLY) ............................................................... 25
Receiving Radio Data System stations.................... 25
Changing the Radio Data System mode .................. 25
PTY SEEK function ................................................ 26
EON function........................................................... 27
ADVANCED SETUP ........................................... 28
Changing the ADVANCED SETUP menu
parameters ........................................................... 28
TROUBLESHOOTING....................................... 30
SPECIFICATIONS .............................................. 33
CONTENTS
INTRODUCTION
PREPARATION
OPERATION
ADDITIONAL INFORMATION
FEATURES
2
Built-in 2-channel power amplifier
Minimum RMS output power
50 W + 50 W (8 ), 0.04% THD, 20 Hz to 20 kHz
Highly dynamic power, low impedance drive
capability
Sophisticated AM/FM tuner
40-station random access preset tuning
Automatic preset tuning
Preset station exchanging capability
Radio Data System tuning capability
(Europe model only)
Other features
PURE DIRECT button used to reproduce the purest
source sound
Continuously variable loudness control
Sleep timer
Remote control capability
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the front panel of this unit or those on the remote control. In case the
button names differ between this unit and the remote control, the names of the buttons on the remote control are given in parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
Please check that you received all of the following parts.
FEATURES
SUPPLIED ACCESSORIES
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
+
u
d
SLEEP
REC
EON
FREQ/TEXT
MODE STARTPTY SEEK
A/B
DISC
DIR A
p
DIR B
A/B/C/D/E
MUTE
PRESET
VOLUME
TAPECD
DEVICE
AMP
w
e
f
b
s
a
DISPLAY
Remote control
Batteries (x2)
(AAA, R03, UM-4)
Indoor FM antenna
(U.S.A., Canada and
General models)
AM loop antenna
Indoor FM antenna
(Europe and Australia
models)
CONTROLS AND FUNCTIONS
3
INTRODUCTION
English
1 STANDBY/ON
Turns on this unit or sets it to the standby mode.
See page
14
for details.
In the standby mode, this unit consumes a small amount of power
to receive infrared signals from the remote control.
2 Remote control sensor
Receives infrared signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit.
4 EDIT
Exchanges the assignment of two preset stations with each
other when TUNER is selected as the input source (see
page 24).
5 FM/AM
Switches the reception band between AM and FM when
TUNER is selected as the input source (see page 20).
6 TUNING l / h
Selects the tuning frequency when TUNER is selected as
the input source (see page 20).
7 TUNING MODE
Switches the tuning mode between automatic (the AUTO
indicator turns on as a result) and manual (the AUTO
indicator turns off as a result) when TUNER is selected as
the input source.
8 MEMORY
Stores a station in the system memory (see page 23).
Sets this unit to the automatic preset tuning mode (see
page 21).
9 PURE DIRECT and indicator
Allows you to listen to a source in the purest possible
sound. The indicator above it lights up when this function
is turned on (see page 16).
0 TAPE MONITOR
Allows you to listen to the sound played back on the tape
deck connected to the TAPE terminals on the rear panel of
this unit.
When the 3-head tape deck is used for recording, you can
also monitor the sound being recorded.
The TAPE MON indicator lights up in the front panel
display when you press TAPE MONITOR (see page 17).
When TAPE MON indicator lights up, you cannot select any
input source.
To listen to the source selected with the INPUT selector, press
TAPE MONITOR again so that the TAPE MON indicator turns
off.
When TAPE (tape deck) is selected with the INPUT selector,
this function will not turn on even if TAPE MONITOR is
pressed.
CONTROLS AND FUNCTIONS
Front panel
STANDBY
/ON
INPUT
PHONES
BASS
SPEAKERS
TAPE MONITORPURE DIRECT
55
1
0
1
44
22
3
3
+
VOLUME
l
TUNING
h
FM/AM
EDIT
A/B/C/D/E
12345678
MEMORY
MAN'L/AUTO FM
TUNING MODE
AUTO/MAN'L
BA
TREBLE
55
1
0
1
44
22
3
3
+
BALANCE
55
1
0
1
44
22
3
3
R
L
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
DISPLAY
2154783096
DCBEFGHIJ
A
(U.S.A. and Canada models)
Note
Notes
CONTROLS AND FUNCTIONS
4
A VOLUME
Increases or decreases the sound output level.
This does not affect the OUT (REC) level.
B INPUT selector
Selects the input source you want to listen to.
C A/B/C/D/E
Selects the preset station group (A to E) when TUNER is
selected as the input source (see page 22).
D PHONES jack
Outputs audio for private listening with your headphones.
Press SPEAKERS A and B so that the SP A/B indicators turn off
before you connect your headphones to the PHONES jack.
E SPEAKERS A/B
Turns on or off the speaker set connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel each time the corresponding button is pressed (see
page 15).
F BASS
Increases or decreases the low frequency response. The 0
position produces a flat response (see page 16).
G TREBLE
Increases or decreases the high frequency response. The 0
position produces a flat response (see page 16).
H BALANCE
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalances caused by
speaker locations or listening room conditions (see page
16).
I LOUDNESS
Retains a full tonal range at any volume level to
compensate for the human ears’ loss of sensitivity to high
and low-frequency ranges at a low volume level (see page
16).
J Preset station number buttons
(1 to 8)
Selects the preset station number (1 to 8) directly when
TUNER is selected as the input source (see page 24).
Note
Note
CONTROLS AND FUNCTIONS
5
INTRODUCTION
English
1 SP (SPEAKERS) A/B indicators
Light up according to the set of speakers selected.
Both indicators light up when both sets of speakers are
selected.
2 TAPE MON (MONITOR) indicator
Lights up while the TAPE monitor function is turned on.
3 MEMORY indicator
Flashes for approximately 5 seconds after MEMORY on
the front panel is pressed. While the MEMORY indicator
is flashing, store the displayed station in the system
memory by using A/B/C/D/E and one of the preset station
number buttons on the front panel.
4 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
5 TUNED indicator
Lights up when this unit is tuned into a station.
6 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
7 SLEEP indicator
Lights up when the sleep timer is turned on.
8 MUTE indicator
Flashes while the MUTE function is turned on.
9 Multi-information display
Shows information when adjusting or changing settings.
Europe model only
0 Radio Data System indicators
The box-shaped indicator beside the name of each Radio
Data System mode lights up when the corresponding
Radio Data System mode is selected.
PTY HOLD indicator
Lights up while searching for stations in the PTY
SEEK mode.
EON indicator
Lights up when the Radio Data System station that
offers the EON data service is being received.
Front panel display
SP
HOLDPTY
A B
TAPE
MON
MEMORY AUTO
TUNED STEREO
SLEEP
EON
PS
RT
PTY
CT
MUTE
09
1 3 4 6 7 85
2
CONTROLS AND FUNCTIONS
6
1 Antenna terminals
Connect FM and AM antennas.
See page 11 for connections information.
2 AUDIO jacks
Connect audio components.
See page 9 for connection information.
3 REMOTE jacks
These jacks are used to input/output remote control
signals.
See page 13 for connection information.
4 PHONO jacks and GND terminal
Connect a turntable.
See page 9 for connection information.
5 SPEAKERS terminals
Connect speakers.
See page 10 for connection information.
6 IMPEDANCE SELECTOR switch
Switches the impedance setting.
See page 10 for details.
7 AC OUTLET(S) (SWITCHED)
Use to supply power to your other audio components.
See page 13 for details.
Asia and General models only
VOLTAGE SELECTOR
See page 13 for details.
Rear panel
GND
AM
ANT
FM
ANT
75
UNBAL.
CD/DVD
AUX
IN
(PLAY)
IN
(PLAY)
OUT
(REC)
OUT
(REC)
TAP E
MD
AUDIOTUNER
AUDIO GND
REMOTE
PHONO
IN
OUT
A OR B: 4MIN. /SPEAKER
A + B: 8MIN. /SPEAKER
A OR B: 8MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SELECTEUR D'IMPEDANCE
SPEAKERS
CLASS 2 WIRING
A
B
AC OUTLETS
SWITCHED
6745
12 3
(U.S.A. and Canada models)
CONTROLS AND FUNCTIONS
7
INTRODUCTION
English
This section describes the function of each button on the
remote control used to control this unit or other
components made by YAMAHA. The functions of the
buttons used to control your other audio components are
the same as those of the corresponding buttons on those
components. Refer to those components’ instruction
manuals for details.
1 Infrared signal transmitter
Sends infrared signals.
2 SLEEP
Sets the sleep timer.
3 Input selector buttons
Select the desired input source.
4 PRESET u / d
Selects the preset station number (1 to 8) when TUNER is
selected as the input source.
5 A/B/C/D/E
Selects the preset station group (A to E) when TUNER is
selected as the input source.
6 Radio Data System/CD player/Cassette tape
deck control buttons
Controls Radio Data System features, YAMAHA CD
players or YAMAHA cassette tape deck.
The Radio Data System features (FREQ/TEXT, PTY SEEK
MODE and PTY SEEK START) are only applicable to the
Europe model and are operational only when TUNER is selected
as the input source and the AMP/DEVICE switch is slid to the
AMP position.
7 AMP/DEVICE switch
Switches the function of the control buttons numbered 6
between controlling this unit and controlling YAMAHA
CD players or YAMAHA cassette tape deck.
8 POWER
Turns on this unit.
9 STANDBY
Sets this unit to the standby mode.
In the standby mode, this unit consumes a small amount of power
to receive infrared signals from the remote control.
0 SPEAKERS A/B
Turns on or off the set of speakers connected to the
SPEAKERS A and/or SPEAKERS B terminals on the rear
panel of this unit when the corresponding button is
pressed each time.
A VOLUME +/
Increases or decreases the sound output level.
This does not affect the OUT (REC) level.
When you press VOLUME +/– to control the sound output
level of this unit, VOLUME on the front panel rotates.
B MUTE
Mutes the sound output. Press again to restore the sound
output to the previous volume level (see page 19).
C CD/TAPE switch
Switches the function of the control buttons numbered 6
between controlling YAMAHA CD players and
controlling YAMAHA cassette tape deck when the
AMP/DEVICE switch is slid to the DEVICE position.
Remote control
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
+
u
d
SLEEP
REC
EON
FREQ/TEXT
MODE STARTPTY SEEK
A/B
DISC
DIR A
p
DIR B
A/B/C/D/E
MUTE
PRESET
VOLUME
TAPECD
DEVICE
AMP
w
e
f
b
s
a
DISPLAY
8
9
0
A
B
C
1
3
7
6
4
5
2
Note
Note
Notes
CONTROLS AND FUNCTIONS
8
Notes on batteries
Change all of the batteries if the operation range of the remote control decreases.
Use AAA, R03, UM-4 batteries for the remote control.
Make sure that the polarities are correct. See the illustration inside the battery compartment of each remote control.
Remove the batteries if the remote control is not used for an extended period of time.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these
different types of batteries may have the same shape and color.
We strongly recommend using alkaline batteries.
If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.
1 Open the battery compartment cover.
2 Insert the supplied batteries in each remote
control according to the polarity markings (+
and –) on the inside of the battery
compartment.
3 Close the cover back.
The remote control transmit a directional infrared beam.
Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit.
Handling the remote control
The area between the remote control and this unit must be clear
of large obstacles.
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following types
of conditions:
places of high humidity, such as near a bath
places of high temperature, such as near a heater or a stove
places of extremely low temperatures
dusty places
Do not expose the remote control sensor to strong lighting, in
particular, an inverter type fluorescent lamp; otherwise, the
remote control may not work properly. If necessary, position
this unit away from direct lighting.
Installing batteries in the remote control
1
3
2
Using the remote control
30 30
Approximately 6 m (19.7 ft)
CONNECTIONS
9
PREPARATION
English
Do not connect this unit or other components to the main power until all connections between components are complete.
Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/
or the speakers.
All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,
refer to the owners manual for each of your components.
Use the RCA type pin plug cables for audio components except speakers.
y
The PHONO jacks are designed to connect a turntable with an MM or high-output MC cartridge. If you have a turntable with a low-
output MC cartridge, use an in-line boosting transformer or an MC-head amplifier when connecting your turntable to the PHONO
jacks.
Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to
the GND terminal for some record players.
CONNECTIONS
CAUTION
GND
AM
ANT
FM
ANT
75
UNBAL.
CD/DVD
AUX
IN
(PLAY)
IN
(PLAY)
OUT
(REC)
OUT
(REC)
TAPE
MD
AUDIOTUNER
AUDIO GND
REMOTE
PHONO
IN OUT
SPEAKERS
A
B
R L
LR LR
L
R
L
R
LRLR
+ +
+
––+
Turntable
CD/DVD player,
etc.
Audio in
MD recorder,
etc.
Tape deck, etc.
Audio out
Audio out
GND
Audio out
Audio in
Audio out
MP3 player, etc.
Audio out
Speakers B
Speakers A
10
CONNECTIONS
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly.
Before connecting the speakers, make sure that the power of this unit is off.
1 Remove approximately 10 mm (3/8 in) of
insulation from the end of each speaker
cable and twist the exposed wires of the
cable together to prevent short circuits.
2 Unscrew the knob.
3 Insert one bare wire into the hole in the side
of each terminal.
4 Tighten the knob to secure the wire.
Connecting the banana plug
(U.S.A., Canada, Australia and General
models only)
First, tighten the knob and then insert the banana plug into
the end of the corresponding terminal.
One or two speaker sets can be connected to this unit. If you use
only one speaker set, connect it to either the SPEAKERS A or B
terminals.
Use speakers with the specified impedance shown on the rear
panel of this unit.
IMPEDANCE SELECTOR switch
Do not slide the IMPEDANCE SELECTOR switch while the
power of this unit is turned on, as doing so may damage the unit.
Select the switch position (left or right) according to the
impedance of the speakers in your system.
The Canada model cannot use two separate speaker sets (A and
B) simultaneously when the IMPEDANCE SELECTOR switch
is slid to the right position.
If this unit fails to turn on, the IMPEDANCE SELECTOR
switch may not be fully slid to either position. If this is the case,
slide the switch all the way to either position when the power
supply to this unit is completely cut off.
Connecting speakers
CAUTION
10 mm (3/8 in)
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)
Notes
Switch
position
Impedance level
Right
If you use one set (A or B), the impedance of
each speaker must be 8
or higher.
If you use two sets (A and B), the impedance
of each speaker must be 16
or higher.
Left
If you use one set (A or B), the impedance of
each speaker must be 4
or higher.
If you use two sets (A and B), the impedance
of each speaker must be 8
or higher.
Notes
Banana plug
CAUTION
11
CONNECTIONS
PREPARATION
English
Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal
strength. Connect each antenna correctly to the designated terminals.
A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult your nearest authorized YAMAHA dealer or service center about outdoor antennas.
If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit.
To minimize interference from automobile ignition, locate the antenna as far from heavy traffic as possible.
Keep the feeder cable or coaxial cable as short as possible. Do not bundle or roll up excess cable.
The antenna should be placed at least 2 meters from reinforced concrete walls or metal structures.
Connecting the AM and FM antennas
Notes
GND
AM
ANT
FM
ANT
75
UNBAL.
TUNER
AUDIO GND
AM loop antenna
(included)
Indoor FM antenna
(included)
Outdoor AM antenna
Use a 5 to 10 m of vinyl-
covered wire extended
outdoors from a window.
Outdoor FM antenna
Ground (GND terminal)
For maximum safety and
minimum interference, connect
the antenna GND terminal to a
good earth ground. A good earth
ground is a metal stake driven into
moist earth.
12
CONNECTIONS
Connecting the AM loop antenna
1 Set up the AM loop antenna.
2 Press and hold the tab.
3 Insert the AM loop antenna lead wires into
the AM ANT terminal.
4 Release the tab.
5 Repeat steps 2 to 4 to insert the AM loop
antenna lead wires into the GND terminal.
6 Orient the AM loop antenna for the best
reception.
The AM loop antenna should be placed away from this unit.
A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. It is recommended
that you should connect a 5 to 10 m of vinyl-covered wire to the
AM ANT terminal and extend it outdoors from a window.
Consult your nearest authorized YAMAHA dealer or service
center about outdoor antennas.
The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
Notes
13
CONNECTIONS
PREPARATION
English
Plug the power supply cord into the AC wall outlet after
all other connections are complete.
REMOTE jacks
Some YAMAHA models are able to connect directly to the
REMOTE jack on the rear panel of this unit. If you own these
products, you may not need to use an infrared emitter. Up to six
YAMAHA components can be connected as shown below.
AC OUTLET(S) (SWITCHED)
Australia model ......................................................1 outlet
Other models ....................................................... 2 outlets
Use these outlets to connect the power supply cords from
your other components to this unit. The AC OUTLET(S)
supplies power to any connected components whenever
the power of this unit is turned on. For information on the
maximum power (total power consumption of
components), see “SPECIFICATIONS” on page 33.
VOLTAGE SELECTOR
(Asia and General models only)
VOLTAGE SELECTOR on the rear panel of this unit must
be set for your local main voltage BEFORE plugging the
power supply cord into the AC wall outlet.
Voltages are as follows:
Asia model ......................... AC 220/230–240 V, 50/60 Hz
General model...... AC 110/120/220/230–240 V, 50/60 Hz
Connecting the power supply cord
REMOTE
IN OUT
A OR B: 4MIN. /SPEAKER
A + B: 8MIN. /SPEAKER
A OR B: 8MIN. /SPEAKER
A + B:16MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SPEAKERS
CLASS 2 WIRING
VO LTAGE
SELECTOR
A
B
AC OUTLETS
SWITCHED
(General model)
AC power supply cord
VOLTAGE SELECTOR
AC OUTLET(S)
REMOTE jacks
Memory back-up
The memory back-up circuit prevents the stored data
from being lost. However, the stored data will be lost if
the power cord is disconnected from the AC wall outlet
for more than one week.
OUTOUT
IN
REMOTE
IN
REMOTE
OUT
IN
REMOTE
REMOTE
This unit
YAMAHA
component
YAMAHA
component
Infrared signal
receiver
14
CONNECTIONS
When all connections are complete, turn on the power of
this unit.
1 Press STANDBY/ON on the front panel (or
POWER on the remote control) to turn on this
unit.
Press STANDBY/ON on the front panel (or
STANDBY on the remote control) to set this unit to
the standby mode.
Turning on and off this unit
STANDBY
/ON
INPUT
PHONES
BASS
TAPE MONITORPURE DIRECT
55
1
0
1
44
22
3
3
+
VOLUME
l
TUNING
h
FM/AM
EDIT
A/B/C/D/E
12345678
MEMORY
MAN'L/AUTO FM
TUNING MODE
AUTO/MAN'L
TREBLE
55
1
0
1
44
22
3
3
+
BALANCE
55
1
0
1
44
22
3
3
R
L
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
SPEAKERS
BA
1
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
SLEEP
1
STANDBY
/ON
Front panel Remote control
or
POWER
PLAYING AND RECORDING
15
OPERATION
English
Extreme caution should be exercised when you play back CDs encoded in DTS.
If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage
your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player
before you play back a CD encoded in DTS.
1 Rotate the INPUT selector on the front panel
(or press one of the input selector buttons on
the remote control) to select the desired
input source.
You cannot select any input source while the TAPE MON
indicator lights up in the front panel display.
2 Press SPEAKERS A and/or SPEAKERS B on
the front panel or on the remote control to
select speakers A and/or speakers B.
Both SPEAKERS A and B can be selected.
Make sure that the IMPEDANCE SELECTOR switch is
correctly set (see page 10).
3 Play the source.
4 Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the sound output level.
5 Press STANDBY/ON on the front panel again
(or press STANDBY on the remote control) to
finish using this unit and set it to the standby
mode.
PLAYING AND RECORDING
CAUTION
Playing a source
Note
STANDBY
/ON
INPUT
PHONES
BASS
SPEAKERS
TAPE MON ITORPURE DIRECT
55
1
0
1
44
22
3
3
+
VOLUME
l
TUNING
h
FM/AM
EDIT
A/B/C/D/E
12345678
MEMORY
MAN'L/AUTO FM
TUNING MODE
AUTO/MAN'L
BA
TREBLE
55
1
0
1
44
22
3
3
+
BALANCE
55
1
0
1
44
22
3
3
R
L
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
1 2
5
4
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
+
u
d
SLEEP
A/B/C/D/E
MUTE
PRESET
VOLUME
2
4
1
INPUT
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
SLEEP
Front panel Remote control
or
Notes
SPEAKERS
BA
A
B
SPEAKERS
or
Front panel
Remote control
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
VOLUME
+
VOLUME
Remote control
Front panel
or
STANDBY
/ON
STANDBY
Remote control
Front panel
or
16
PLAYING AND RECORDING
Adjusting the BALANCE control
Adjusts the sound output balance of the left and right
speakers to compensate for sound imbalance caused by
speaker locations or listening room conditions.
Using the PURE DIRECT button
Routes input signals from your audio sources so that the
input signals bypass the BASS, TREBLE, BALANCE and
LOUDNESS controls, thus eliminating any alterations to
the audio signals and creating the purest possible sound.
Adjusting the BASS and TREBLE
controls
Adjust the high and low frequency response.
BASS
Increases or decreases the low frequency response.
TREBLE
Increases or decreases the high frequency response.
Adjusting the LOUDNESS control
Retains a full tonal range at any volume level, thus
compensating for the human ears’ loss of sensitivity to
high and low-frequency ranges at a low volume level.
If the PURE DIRECT button is turned on with the LOUDNESS
control set at a certain level, the input signals bypass the
LOUDNESS control, resulting in a sudden increase in the sound
output level. To prevent your ears or the speakers from being
undesirably damaged, be sure to press the PURE DIRECT button
AFTER lowering the sound output level or AFTER checking that
the LOUDNESS control is properly set.
1 Rotate the LOUDNESS control on the front
panel to the FLAT position.
2 Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to set the
sound output level to the loudest listening
level that you would listen to.
3 Rotate the LOUDNESS control until the
desired volume is obtained.
Adjusting the tonal quality
BALANCE
55
1
0
1
44
22
3
3
R
L
PURE DIRECT
BASS
55
1
0
1
44
22
3
3
+
TREBLE
55
1
0
1
44
22
3
3
+
CAUTION
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
VOLUME
+
VOLUME
Remote control
Front panel
or
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
17
PLAYING AND RECORDING
OPERATION
English
The VOLUME, BASS, TREBLE, BALANCE and
LOUDNESS controls and the PURE DIRECT buttons have no
effect on the source being recorded.
Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording copyright-protected
material may infringe on copyright laws.
1 Play the selected source to record from.
2 Rotate the INPUT selector on the front panel
to select the source you want to record from.
You cannot select any input source while the TAPE MON
indicator lights up in the front panel display.
3 Rotate VOLUME on the front panel (or press
VOLUME +/– on the remote control) to adjust
the sound output level of the selected source
to record from.
4 Begin recording on the MD recorder, the tape
deck or the VCR connected to this unit.
y
If the 3-head tape deck is used for recording, you can monitor the
sound of recording by pressing TAPE MONITOR.
Recording a source
Notes
Note
STANDBY
/ON
INPUT
PHONES
BASS
TAPE MONPURE DIRECT
55
1
0
1
44
22
3
3
+
VOLUME
l
TUNING
h
FM/AM
EDIT
A/B/C/D/E
12345678
MEMORY
MAN'L/AUTO FM
TUNING MODE
AUTO/MAN'L
TREBLE
55
1
0
1
44
22
3
3
+
BALANCE
55
1
0
1
44
22
3
3
R
L
LOUDNESS
57
1
FLAT
6
48
210
30dB
3
9
SPEAKERS
BA
2
3
0
12
2
8
4
20
60
26
40
16
-dB
INPUT
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
SLEEP
Front panel Remote control
or
0
12
12
2
8
4
20
20
60
60
26
26
40
40
16
16
-dB
-dB
VOLUME
+
VOLUME
Remote control
Front panel
or
18
PLAYING AND RECORDING
Use this feature to automatically set this unit to the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to the AC OUTLET(S).
The sleep timer can only be set with the remote control.
1 Press one of the input selector buttons on
the remote control to select an input source.
2 Start playback on the selected input source.
3 Press SLEEP repeatedly to set the amount of
time before this unit is set to the standby
mode.
Each time you press SLEEP, the front panel display
changes as shown below.
The SLEEP indicator flashes while switching the
amount of time for the sleep timer.
4 Press SLEEP repeatedly so that SLEEP OFF
appears in the front panel display.
After a few seconds, SLEEP OFF disappears from the
front panel display, and the SLEEP indicator turns
off.
y
The sleep timer setting can also be canceled by pressing
STANDBY on the remote control (or STANDBY/ON on the front
panel) to set this unit to the standby mode.
Using the sleep timer
Note
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
+
u
d
SLEEP
A/B/C/D/E
MUTE
PRESET
VOLUME
1
3
CD/DVD PHONO TUNER
MD TAPE AUX
SPEAKERS
B
A
POWER
STANDBY
SLEEP
SLEEP
SLEEP 120 min SLEEP 90 min
SLEEP 60 minSLEEP 30 minSLEEP OFF
SLEEP
SLEEP
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206

Yamaha RX-397 Omistajan opas

Tyyppi
Omistajan opas