Philips HD7768/70 Ohjekirja

HD7768

1

2

3

5

6

4

8

9

10

11

12

22

23

24

25

7

1513

14 16 19 21

17 18 20

1

English 6

Dansk 15

Español 24

Français 34

Nederlands 44

Norsk 54

Português 63

Suomi 73

Svenska 82

English

Introduction

Thank you for buying Philips. To register your new product, please go to www.philips.com/grindbrew.

On this website, you can also find handy videos, delicious recipes, frequently asked questions and get

support.

General description (Fig. 1)

1 Filter basket

2 Drip stop

3 Filter basket holder

4 Water level indicator

5 Water reservoir lid

6 Bean container lid

7 Coarseness knob

8 Coffee bean container

9 Grinder funnel lid

10 Lock of grinder funnel lid

11 Water filling hole

12 Display

13 Pre-ground coffee icon

14 Number of cups

15 Coffee cup icon

16 Strength select coffee bean icon

17 Strength select button

18 Timer button

19 Control knob

20 Time indication

21 Timer icon

22 On/off button

23 Glass jug lid

24 Glass jug

25 Bean chute cleaning brush

Important

Danger

-

Never immerse the appliance in water or any other liquid, nor

rinse it under the tap.

Warning

-

Check if the voltage indicated on the appliance corresponds to

the local mains voltage before you connect the appliance.

-

Do not use the appliance if the plug, the mains cord or the

appliance itself is damaged.

6

English

-

If the mains cord is damaged, you must have it replaced by

Philips, a service center authorized by Philips or similarly qualified

persons in order to avoid a hazard.

-

Connect the appliance to an earthed wall socket.

-

This appliance can be used by children aged from 8 years and

above and by persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and if they understand the hazards

involved. Cleaning and user maintenance shall not be made by

children unless they are older than 8 and supervised. Keep the

appliance and its cord out of reach of children aged less than 8

years.

-

Children shall not play with the appliance.

-

Only use this appliance for its intended purpose to avoid

potential hazard or injury.

-

Do not let the mains cord hang over the edge of the table or

worktop on which the appliance stands.

-

Never pour water into the bean container, as this damages the

appliance.

-

Do not touch the grinding burrs of the of the appliance, especially

when the appliance is connected to a wall socket.

-

Do not touch the hot surfaces of the appliance when it operates.

-

Do not empty the water reservoir by tilting the appliance, as this

can damage the appliance. To empty the appliance, follow the

instructions for flushing the appliance (see 'Flushing the

appliance').

-

If a problem occurs that you cannot solve by means of this user

manual, contact the Consumer Care Center in your country. If the

problem cannot be solved, take the appliance to a service center

authorized by Philips for examination or repair. Do not attempt to

repair the appliance yourself, otherwise your warranty becomes

invalid.

7

English

Caution

-

Do not place the appliance on a hot surface and prevent the

mains cord from coming into contact with hot surfaces.

-

Do not place the appliance in a cabinet when in use.

-

Unplug the appliance if problems occur during grinding or

brewing and before you clean it.

-

Keep the plug and the wall socket dry.

-

Do not lift and move the appliance while it is operating.

-

The jug is hot during and after brewing. Always hold the jug by its

handle.

-

Never use the jug in a microwave oven.

-

Wait until the appliance has cooled down before you store it. The

hotplate and the coffee jug may be hot.

-

After you have unpacked the appliance, make sure it is complete

and undamaged. If in doubt, do not use the appliance but contact

the Consumer Care Center in your country.

-

This appliance is intended to be used in household and similar

applications such as farm houses, bed and breakfast type

environments, staff kitchen areas in shops, offices and other

working environments, and by clients in hotels, motels and other

residential type environments.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to

electromagnetic fields.

Before first use

Setting the clock

1 Put the mains plug in the wall socket. The time indication flashes on the display to indicate that

you have to set the clock time.

2 Turn the control knob to set the hour. The hour indication flashes (Fig. 2).

3 Press the center of the control knob to confirm the hour (Fig. 3).

4 The minutes indication starts flashing to indicate that you have to set the minutes (Fig. 4).

5 Turn the control knob to set the minutes (Fig. 5).

6 Press the center of the control knob to confirm the minutes (Fig. 6).

7 The display shows the set clock time. The coffeemaker is now ready for use.

8

English

Setting the automatic switch-off time

You can choose how long you want your coffee to stay hot after brewing by adjusting the time after

which the appliance automatically switches off. The default automatic switch-off time is 30 minutes.

The maximum automatic switch-off time is 120 minutes. To adjust the automatic switch-off time,

follow the steps below.

1 Make sure that the appliance is switched off but the mains plug is in the wall socket.

2 Press the center of the control knob until the display starts flashing.

3 Turn the control knob to increase or decrease the time. 1 is 10 minutes, 2 is 20 minutes, 3 is 30

minutes and so on until 12 is 120 minutes.

4 Press the center of the control knob to confirm the automatic switch-off time.

Note: The appliance always saves the last setting.

Flushing the appliance

Always flush the coffeemaker once before first use by following the steps below.

Warning: Never pour water into the bean container, as this damages the coffeemaker.

1 Open the water reservoir lid. Fill the water reservoir with fresh cold water up to the 8-cup indication

(Fig. 7).

Caution: Do not put coffee beans or pre-ground coffee in the water reservoir.

2 Close the water reservoir lid.

3 Put the jug in the appliance (Fig. 8).

4 Press the on/off button (Fig. 9). The display lights up and the appliance beeps.

5 Press the strength select button (Fig. 10).

6 Turn the control knob to choose the pre-ground coffee setting (Fig. 11). The pre-ground coffee icon

starts flashing.

7 Press the center of the control knob twice to confirm (Fig. 12). The appliance starts the flushing

process.

8 Let the appliance operate until the flushing process is finished. It is finished when the appliance

stops beeping.

9 Empty the jug.

10 Press the on/off button to switch off the appliance.

Using the appliance

Filling the water reservoir

There are indications for 2 to 10 cups (275ml to 1375ml) on the water-level window. You can use these

indications to determine how much water to put in the water reservoir. The reflection changes from

light to dark for each cup of water added.

1 Open the water reservoir lid and fill the water reservoir with the required amount of cold water (Fig.

7).

Note: Do not fill the water reservoir beyond the 10-cup indication.

Note: Make sure that the amount of water you pour into the water reservoir is consistent with the

number of cups you want to brew. The coffeemaker uses all the water in the water reservoir.

9

English

Using coffee beans

Warning: Always keep the water reservoir lid closed when you fill the coffee bean

container with coffee beans. Otherwise coffee beans can fall into the water reservoir

and block up the water inlet.

1 Open the coffee bean container lid (Fig. 13).

2 Fill the container with coffee beans. Make sure that there are enough coffee beans in the container

for the amount of coffee you want to brew (Fig. 14).

Note: Always make sure that the bean container is at least half full.

Warning: To prevent the grinder from jamming, do not use unroasted or caramelized

beans. Use coffee beans instead of espresso beans, as espresso beans may damage

the grinder.

3 Open the filter basket holder (Fig. 15).

4 Place a paper filter (type 1x4 or no. 4) or the permanent filter in the filter basket (Fig. 16).

5 Close the filter basket holder.

6 Turn the coarseness knob to select the desired type of grind (from fine to coarse). There are nine

grind settings (Fig. 17).

Tip: The coarseness knob allows you to choose between 9 different settings. The icons indicate 3

preselected optimal settings, but you can choose any setting in between. We advise you to

experiment with the different grind settings to find out which setting you prefer.

7 Press the strength button (Fig. 10). The coffee bean icons start flashing.

8 Turn the control knob to select the desired coffee strength: 1 bean for mild coffee, 2 beans for

medium-strong coffee or 3 beans for strong coffee.

9 Press the center of the control knob to confirm the strength (Fig. 6).

10 To select the number of cups, turn the control knob until the desired number of cups flashes on the

display (Fig. 18).

Note: Please keep in mind that the coffeemaker uses all the water in the water reservoir. If you

select a number of cups that is smaller than the amount of water, the coffee becomes weaker than

you intended.

11 Press the center of the control knob to confirm the number of cups (Fig. 6).

12 Press the center of the control knob again. The appliance beeps and starts grinding the required

amount of coffee beans. When the grinding process is finished, the appliance starts brewing coffee

13 Wait until the coffeemaker has stopped beeping before you remove the jug.

Note: After brewing, coffee drips from the filter basket for several seconds.

14 The appliance keeps your coffee hot until it switches off automatically. If you do not need your

coffee to be kept hot, press the on/off button to switch off the appliance.

Using pre-ground coffee

If you want to use pre-ground coffee instead of coffee beans, follow the steps below.

1 Open the water reservoir lid and fill the water reservoir with the required amount of cold water (Fig.

7).

2 Open the filter basket holder (Fig. 15).

3 Place a paper filter (type 1x4 or no. 4) or the permanent filter in the filter basket.

4 Put pre-ground coffee in the paper filter or in the permanent filter.

5 Close the filter basket holder.

10

English

6 Put the jug in the appliance (Fig. 8).

7 Press the on/off button (Fig. 9). The display lights up.

8 Press the strength select button (Fig. 10).

9 Turn the control knob to choose the pre-ground coffee setting (Fig. 11). The pre-ground coffee icon

lights up.

10 Press the center of the control knob to confirm (Fig. 6).

11 Then press the center of the control knob again to start the brewing process (Fig. 6).

12 Wait until the coffeemaker has stopped beeping before you remove the jug.

Note: After brewing, coffee drips from the filter basket for several seconds.

13 The appliance keeps your coffee hot until it switches off automatically. If you do not need your

coffee to be kept hot, press the on/off button to switch off the appliance.

Setting the timer

The timer enables you to program the time at which you want the brewing process to start. Make sure

that all steps of brewing coffee with either preground coffee or coffee beans have been taken before

you set the timer.

1 Press the timer button (Fig. 19) and the timer icon will appear on the display. The hour indication

flashes to indicate that you have to set the hour.

2 Turn the knob to set the hour (Fig. 20).

3 Press the center of the control knob to confirm the hour (Fig. 21). The minutes indication starts

flashing to indicate that you have to set the minutes.

4 Turn the control knob to set the minutes (Fig. 22).

5 Press the center of the knob to confirm the minutes and the time set (Fig. 21). The timer is set and

the brewing process will start at the preset time.

Note: To cancel the timer, simply press the timer button again and the timer icon will disappear from

the display.

Drip stop function

The drip stop function enables you to remove the jug from the coffeemaker before the brewing

process is finished. When you remove the jug, the drip stop stops the flow of coffee into the jug.

Note: The brewing process does not stop when you remove the jug. If you do not put the jug back into

the appliance within 20 seconds, the filter basket overflows.

Cleaning and maintenance

Cleaning after every use

Never immerse the appliance in water or any other liquid, nor rinse it under the tap.

1 Remove the mains plug from the wall socket.

2 Wipe the outside of the coffeemaker with a damp cloth.

3 Clean the filter basket and the permanent filter with hot water and some washing-up liquid or

clean them in the dishwasher.

11

English

Cleaning the grinder funnel

Important: Clean the grinder funnel every 1 to 2 weeks to prevent clogging with ground coffee. This

is easily and quickly done by following the steps below.

Note: Make sure the coffee bean container is empty before you start the cleaning procedure.

1 Press the on/off button to switch off the appliance (Fig. 23).

2 Open the filter basket holder (Fig. 15).

3 Place a paper filter (type 1x4 or no. 4) or the permanent filter in the filter basket (Fig. 16).

4 Close the filter basket holder.

5 Use the end of the bean chute cleaning brush to open the grinder funnel lid (Fig. 24).

6 Press and hold the strength select button for 4 seconds (Fig. 25). The grinder starts cleaning itself.

7 When the grinder has stopped cleaning, use the bean chute cleaning brush to brush ground coffee

residues into the lower part of the funnel (Fig. 26). The ground coffee residues fall into the filter

basket.

8 Close the lid of the grinder funnel.

9 Remove the paper filter or permanent filter with the ground coffee residues.

Descaling the coffeemaker

Descale the coffeemaker when you notice excessive steaming or when the brewing time increases. It

is advisable to descale the coffeemaker every two months. Only use white vinegar to descale, as other

products may cause damage to the coffeemaker. For more information on descaling, see

www.philips.com/descale-coffeemaker.

Warning: Never use vinegar with an acetic acid content of 8 % or more, natural vinegar,

powder descalers or tablet descalers to descale the appliance, as this may cause

damage.

1 Open the water reservoir lid.

2 Fill the water reservoir up to 10 cup indication with white vinegar (4% acetic acid).

3 Place a paper filter (type 1x4 or no. 4) or the permanent filter in the filter basket and close the filter

basket holder.

4 Put the empty jug in the appliance.

5 Put the mains plug in the wall socket.

6 Press the on/off button to switch on the appliance (Fig. 9). The display lights up.

7 Press the strength select button and turn the control knob to choose the pre-ground coffee setting

(Fig. 11).

8 Press the center of the control knob twice to confirm and start the brewing process.

9 Wait until half of the vinegar has flowed into the jug. Then press the on/off button to interrupt the

brewing process. Let the vinegar act for at least 15 minutes.

10 Press the on/off button to switch the coffeemaker back on.

11 Press the center of the control knob twice to let the appliance complete the brewing process (Fig.

12).

12 Empty the jug and remove the paper filter or the permanent filter with the scale residues.

13 Fill the water reservoir with fresh cold water and press the center of the control knob twice to start

another brewing process (Fig. 12). Let the coffeemaker complete the entire brewing process and

empty the jug.

12

English

Note: If necessary repeat step 14 until the water that comes out of the appliance no longer tastes or

smells of vinegar.

14 Clean the filter basket and the jug with hot water and some washing-up liquid.

15 Press the on/off button on the front of the appliance to switch off the appliance (Fig. 23).

Warranty and support

If you need information or support, please visit www.philips.com/support or read the international

warranty leaflet.

Ordering accessories

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips

dealer. You can also contact the Philips Consumer Care Center in your country (see the international

warranty leaflet for contact details).

Recycling

-

This symbol means that this product shall not be disposed of with normal household waste

(2012/19/EU) (Fig. 27).

-

Follow your country's rules for the separate collection of electrical and electronic products. Correct

disposal helps prevent negative consequences for the environment and human health.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you

are unable to solve the problem with the information below, visit www.philips.com/support for a list

of frequently asked questions or contact the Consumer Care Center in your country.

Problem

Solution

The appliance does not

work.

Put the mains plug in the wall socket and press the on/off button to

switch on the appliance.

Make sure that the voltage indicated on the appliance corresponds to

the local mains voltage.

Fill the water reservoir with water.

Close the lid of the grinder funnel.

The grinder does not work

or does not work properly.

Make sure that you did not select pre-ground coffee. If the symbol for

pre-ground coffee is visible on the display, you selected pre-ground

coffee.

Clean the grinder funnel by following the instructions.

When I use the grinder,

the coffee is too weak.

Make sure that the number of cups you selected is consistent with the

amount of water in the water reservoir. Please keep in mind that the

coffeemaker uses up all the water in the water reservoir.

Use the strength select button to set the coffee strength to ‘strong’.

Use coffee beans of a stronger blend or flavor.

13

English

When I use pre-ground

coffee, the coffee is too

weak.

Make sure that the amount of pre-ground coffee in the filter is

consistent with the amount of water in the water reservoir. Please keep

in mind that the appliance uses all the water in the water reservoir.

Use ground coffee of a stronger blend or flavor.

To increase the coffee strength, increase the amount of pre-ground

coffee or decrease the amount of water.

The filter overflows when I

remove the jug from the

appliance while it is

brewing coffee.

If you remove the jug for more than 20 seconds during the brewing

process, the drip stop causes the filter basket to overflow. Also note that

the coffee does not reach its full taste before the end of the brewing

process. Therefore we advise you not to remove the jug and pour out

the coffee before the end of the brewing process.

The appliance continues

to drip long after the

brewing process has

ended.

The dripping is caused by condensation of steam. It is completely

normal that the appliance drips for some time.

If the dripping does not stop, the drip stop may be clogged. To clean the

drip stop, open the filter basket holder and take out the filter basket.

Rinse the filter basket and the drip stop under the tap.

The coffee is not hot

enough.

The coffee in the jug cools down faster if you brew only a few cups. The

coffee stays hot longer if you brew 10 cups, which is a full jug.

Descale the appliance (see 'Descaling the coffeemaker').

The appliance does not

start cleaning the grinder

funnel.

Make sure that the appliance is plugged in.

Open the lid of the grinder funnel before you press and hold the

strength select button for 4 seconds.

Press and hold the strength select button for 4 seconds until the grinder

starts cleaning itself.

The appliance works but

makes a beeping sound.

Please check if the lid of the grinder funnel is closed properly.

The coffee beans seem to

be used up quickly.

To brew a perfect cup of coffee, the appliance needs a certain amount

of ground coffee. The amount of coffee beans the appliance uses to

obtain the optimal amount of ground coffee per cup is normal.

The timer does not work. Make sure to complete all steps for brewing coffee with coffee beans or

pre-ground coffee before you set the timer.

14

English

Dansk

Introduktion

Tak, fordi du har købt et Philips-produkt. Gå til www.philips.com/grindbrew for at registrere dit nye

produkt. På dette websted finder du også praktiske videoer, lækre opskrifter og ofte stillede

spørgsmål, og her kan du også få support.

Generel beskrivelse (fig. 1)

1 Filterkurv

2 Drypstop-funktion

3 Holder til filterkurv

4 Vandstandsindikator

5 Låg til vandtank

6 Låg til beholder til bønner

7 Knap til formalingsgrad

8 Beholder til kaffebønner

9 Låg over kværnens tragt

10 Lås til låget over kværnens tragt

11 Vandpåfyldningshul

12 Display

13 Ikon for formalet kaffe

14 Antal kopper

15 Ikon for kaffekop

16 Ikon med kaffebønne for valg af kaffestyrke

17 Knap til valg af kaffestyrke

18 Timer-knap

19 Kontrolknap

20 Tidsangivelse

21 Ikon for timer

22 On/off-knap

23 Låg til glaskande

24 Glaskande

25 Rengøringsbørste til kaffebønneslisken

Vigtigt

Fare

-

Apparatet må aldrig kommes ned i vand eller andre væsker, ej

heller skylles under vandhanen.

Advarsel

-

Kontrollér, om den angivne netspænding på apparatet svarer til

den lokale netspænding, før du slutter strøm til apparatet.

-

Brug aldrig apparatet, hvis netstik, netledning eller selve

apparatet er beskadiget.

15

Dansk

-

Hvis netledningen beskadiges, må den kun udskiftes af Philips, et

autoriseret Philips-serviceværksted eller en tilsvarende

kvalificeret fagmand for at undgå enhver risiko.

-

Apparatet skal sluttes til en stikkontakt med jordforbindelse.

-

Dette apparat kan bruges af børn fra 8 år og op og personer med

nedsatte fysiske, sensoriske eller mentale evner eller manglende

viden eller erfaring, hvis de er blevet vejledt eller instrueret i brug

af apparatet på en sikker måde, og hvis de forstår de involverede

risici. Rengøring og vedligeholdelse må ikke foretages af børn,

medmindre de er over 8 år gamle og under opsyn. Hold apparatet

og dets ledning uden for rækkevidde af børn under 8 år.

-

Lad ikke børn lege med apparatet.

-

Brug kun dette apparat til dets tilsigtede formål for at undgå

potentielle farer og skader.

-

Lad aldrig ledningen hænge ud over kanten af det bord eller den

plads, som apparatet står på.

-

Hæld aldrig vand i beholderen til kaffebønner, da det kan

beskadige kaffemaskinen.

-

Undgå at røre ved kværnbladene i apparatet, især når apparatet

er tilsluttet en stikkontakt.

-

Rør aldrig ved apparatets varme dele under betjening.

-

Tøm ikke vandtanken ved at vippe apparatet, da det kan

beskadige apparatet. Tøm vandtanken ved at følge vejledningen

for gennemskylning af apparatet (se 'Gennemskylning af

apparatet').

-

Skulle der opstå problemer, som du ikke kan afhjælpe vha. denne

brugervejledning, bedes du kontakte det lokale Philips

Kundecenter. Hvis du ikke kan løse problemet, skal du aflevere

apparatet hos et autoriseret Philips-serviceværksted. Forsøg ikke

at reparere apparatet selv, da din garanti ellers bliver ugyldig.

Forsigtig

-

Stil aldrig apparatet på et varmt underlag, og sørg for, at

netledningen ikke kommer i berøring med varme flader.

16

Dansk

-

Placer ikke apparatet i et skab, mens den er i brug.

-

Tag stikket ud af stikkontakten, hvis der opstår problemer under

formaling eller brygning samt før rengøring af apparatet.

-

Både stik og stikkontakt skal holdes tørre.

-

Undlad at flytte eller løfte apparatet under brug.

-

Kanden er varm under og efter brygningen. Brug altid håndtaget,

når du skal løfte kanden.

-

Brug aldrig kanden i en mikroovn.

-

Læg aldrig apparatet væk, før det er helt afkølet. Varmepladen og

kaffekanden kan være varme.

-

Efter udpakningen af apparatet skal du kontrollere, at det er helt

og ubeskadiget. Hvis du er i tvivl, bør du ikke bruge apparatet men

kontakte dit lokale Philips Kundecenter.

-

Dette apparat er beregnet til brug i hjemmet og andre lignende

steder; såsom gårde, bed and breakfast-steder,

personalekøkkener i butikker, på kontorer og andre

arbejdspladser. Det kan også benyttes af gæster på hoteller og

moteller.

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle branchens gældende standarder og regler angående

eksponering for elektromagnetiske felter.

Før apparatet tages i brug

Indstilling af uret

1 Sæt stikket i en stikkontakt. Timeangivelsenblinker på displayet for at indikere, at du skal indstille

klokkeslættet.

2 Drej kontrolknappen for at indstille klokken. Timeangivelsen blinker (fig. 2).

3 Tryk midt på kontrolknappen for at bekræfte timeangivelsen (fig. 3).

4 Minutangivelsen begynder at blinke for at indikere, at du skal indstille antal minutter (fig. 4).

5 Drej kontrolknappen for at indstille antal minutter (fig. 5).

6 Tryk midt på kontrolknappen for at bekræfte antal minutter (fig. 6).

7 Displayet viser klokkeslættet. Kaffemaskinen er nu klar til brug.

Indstilling af automatisk slukketid

Du kan vælge, hvor længe kaffen skal holdes varm efter brygning ved at indstille den tid, hvor

apparatet automatisk skal slukke. Standardindstillingen for automatisk slukketid er 30 minutter.

17

Dansk

Maksimumindstillingen for automatisk slukketid er 120 minutter. Følg nedenstående trin for at indstille

den automatiske slukketid.

1 Kontrollér, at apparatet er slukket, og at stikket er sat i stikkontakten.

2 Tryk midt på kontrolknappen, indtil displayet begynder at blinke.

3 Drej kontrolknappen for at skrue tiden frem eller tilbage. 1 er 10 minutter, 2 er 20 minutter, 3 er 30

minutter op til 12, der er 120 minutter.

4 Tryk midt på kontrolknappen for at bekræfte den automatiske slukketid.

Bemærk: Apparatet gemmer altid den sidste indstilling.

Gennemskylning af apparatet

Husk altid at gennemskylle kaffemaskinen før første brug ved at følge nedenstående trin.

Advarsel: Hæld aldrig vand i beholderen til kaffebønner, da det kan beskadige

kaffemaskinen.

1 Åbn låget til vandtanken. Fyld vandtanken med friskt, koldt vand op til markeringen (fig. 7) for 8

kopper.

Forsigtig: Kom ikke kaffebønner eller formalet kaffe i vandtanken.

2 Luk låget til vandtanken.

3 Sæt kanden i apparatet (fig. 8).

4 Tryk på on/off-knappen (fig. 9). Displayet lyser, og apparatet bipper.

5 Tryk på knappen (fig. 10) til valg af kaffestyrke.

6 Drej kontrolknappen for at vælge indstillingen (fig. 11) til formaling af kaffe. Ikonet for formaling af

kaffe begynder at blinke.

7 Tryk endnu en gang midt på kontrolknappen for at bekræfte (fig. 12). Apparatet går i gang med

gennemskylningen.

8 Lad apparatet køre, indtil skylningen er afsluttet. Skylningen er afsluttet, når apparatet stopper med

at bippe.

9 Tøm kanden.

10 Sluk for apparatet ved at trykke på on/off-knappen.

Sådan bruges apparatet

Påfyldning af vandtanken

Der er angivelser for 2 til 10 kopper (275ml til 1375ml) på vandstandsruden. Du kan bruge disse

angivelser til at afgøre, hvor meget vand du skal hælde i vandtanken. Reflektionen ændres fra lys til

mørk for hver kop vand, der hældes i.

1 Åbn låget til vandtanken, og fyld vandtanken med den påkrævede mængde koldt vand (fig. 7).

Bemærk: Fyld aldrig vandtanken til op over mærket for 10 kopper.

Bemærk: Sørg for, at den mængde vand du hælder i vandtanken, svarer til antallet af kopper, du vil

brygge. Kaffemaskinen bruger alt vandet i vandtanken.

18

Dansk

Brug af kaffebønner

Advarsel: Sørg for, at låget til vandtanken altid er lukket, når du fylder kaffebønner i

beholderen til kaffebønner. Ellers er der risiko for, at der falder kaffebønner ned i

vandtanken, der tilstopper vandindtaget.

1 Åbn låget (fig. 13) til kaffebønnebeholderen.

2 Fyld kaffebønner i beholderen. Sørg for, at der er nok kaffebønner i beholderen til den mængde

kaffe, du vil brygge (fig. 14).

Bemærk: Sørg altid for, at bønnebeholderen er mindst halvt fuld.

Advarsel: Brug ikke uristede eller karamelliserede bønner, der kan forårsage, at

kværnen låser sig fast. Brug kaffebønner i stedet for espressobønner, idet

espressobønner kan beskadige kværnen.

3 Åbn holderen til filterkurven (fig. 15).

4 Sæt et papirfilter (type 1x4 eller nr. 4) eller det permanente filter i filterkurven (fig. 16).

5 Luk holderen til filterkurven.

6 Drej på knappen til formalingsgrad for at vælge den ønskede type maling (fra fin til grov). Der er ni

formalingsindstillinger (fig. 17).

Tip: Med knappen for formalingsgrad kan du vælge mellem ni forskellige indstillinger. Ikonerne

angiver tre forudvalgte optimale indstillinger, men du kan også vælge alle indstillinger mellem

ikonerne. Vi anbefaler, at du eksperimenterer med de forskellige malingsindstillinger for at finde ud

af, hvilken indstilling du foretrækker.

7 Tryk på knappen til valg af kaffestyrke (fig. 10). Ikonet for kaffebønner begynder at blinke.

8 Drej kontrolknappen for at vælge den ønskede kaffestyrke: 1 bønne for mild kaffe, 2 bønner for

kaffe af mediumstyrke eller 3 bønner for stærk kaffe.

9 Tryk midt på kontrolknappen for at bekræfte styrken (fig. 6).

10 Du vælger antallet af kopper ved at dreje kontrolknappen, indtil det ønskede antal kopper blinker

på displayet (fig. 18).

Bemærk: Husk, at kaffemaskinen bruger alt vandet i vandtanken. Hvis du vælger et antal kopper,

der er mindre end den tilsvarende vandmængde, vil kaffen blive svagere.

11 Tryk midt på kontrolknappen for at bekræfte antallet af kopper (fig. 6).

12 Tryk endnu en gang midt på kontrolknappen. Kaffemaskinen bipper, og begynder at male den

ønskede mængde kaffebønner. Når bønnerne er malet, begynder maskinen at brygge kaffe.

13 Vent, indtil kaffemaskinen er stoppet med at bippe, inden du fjerner kanden.

Bemærk: Efter brygningen drypper der kaffe fra filterkurven i flere sekunder.

14 Apparatet holder kaffen varm, indtil det slukkes automatisk. Hvis du ikke har brug for at få kaffen

holdt varm, skal du trykke på on/off-knappen for at slukke apparatet.

Brug af formalet kaffe

Hvis du vil bruge formalet kaffe i stedet for kaffebønner, skal du følge nedenstående trin.

1 Åbn låget til vandtanken, og fyld vandtanken med den påkrævede mængde koldt vand (fig. 7).

2 Åbn holderen til filterkurven (fig. 15).

3 Sæt et papirfilter (type 1x4 eller nr. 4) eller det permanente filter i filterkurven.

4 Put formalet kaffe i papirfiltret eller i det permanente filter.

5 Luk holderen til filterkurven.

6 Sæt kanden i apparatet (fig. 8).

19

Dansk

7 Tryk på on/off-knappen (fig. 9). Displayet lyser.

8 Tryk på knappen til valg af kaffestyrke (fig. 10).

9 Drej kontrolknappen for at vælge indstillingen til formaling af kaffe (fig. 11). Ikonet for formaling af

kaffe lyser.

10 Tryk midt på kontrolknappen for at bekræfte (fig. 6).

11 Tryk derefter midt på kontrolknappen igen for at starte brygningen (fig. 6).

12 Vent, indtil kaffemaskinen er stoppet med at bippe, inden du fjerner kanden.

Bemærk: Efter brygningen drypper der kaffe fra filterkurven i flere sekunder.

13 Apparatet holder kaffen varm, indtil det slukker automatisk. Hvis du ikke har brug for at få kaffen

holdt varm, skal du trykke på on/off-knappen for at slukke apparatet.

Indstilling af timeren

Timeren gør det muligt at indstille det tidspunkt, hvor brygningen skal starte. Sørg for, at alle trin i

kaffebrygning med enten formalet kaffe eller kaffebønner er valgt, før du indstiller timeren.

1 Tryk på timer-knappen (fig. 19), og timerikonet vises på skærmen. Timetallet blinker for at indikere,

at du skal indstille antal timer.

2 Drej på knappen for at indstille antal timer (fig. 20).

3 Tryk midt på kontrolknappen for at bekræfte timeangivelsen (fig. 21). Minutangivelsen begynder at

blinke for at indikere, at du skal indstille antal minutter.

4 Drej kontrolknappen for at indstille antal minutter (fig. 22).

5 Tryk midt på kontrolknappen for at bekræfte antal minutter og det indstillede klokkeslæt (fig. 21).

Timeren er indstillet, og brygningen starter på det angivne tidspunkt.

Bemærk: Hvis du vil annullere timeren, skal du blot trykke på timer-knappen igen, så timerikonet

forsvinder fra displayet.

Drypstop-funktion

Drypstop-funktionen gør det muligt at fjerne kanden fra kaffemaskinen, inden bryggeprocessen er

færdig. Når du fjerner kanden, stopper drypstop-funktionen kaffens løb ned i kanden.

Bemærk: Brygningen stopper ikke, når du fjerner kanden. Hvis du ikke stiller kanden tilbage i apparatet

inden for 20 sekunder, flyder filterkurven over.

Rengøring og vedligeholdelse

Rengøring efter hver brug

Apparatet må aldrig kommes ned i vand eller andre væsker, ej heller skylles under

vandhanen.

1 Tag stikket ud af stikkontakten.

2 Tør kaffemaskinens yderside af med en fugtig klud.

3 Rengør filterkurven og det permanente filter med varmt vand og lidt opvaskemiddel, eller vask dem

i opvaskemaskinen.

20

Dansk

Sivu latautuu ...

Philips HD7768/70 Ohjekirja

Tämä käsikirja sopii myös

Philips HD7768/70 Ohjekirja

muilla kielillä

Liittyvät paperit

Muut asiakirjat