Yamaha Pm7 Asennusohje

Kategoria
Audio equalizers
Tyyppi
Asennusohje
DIGITAL MIXING CONSOLE
CSD-R7
System Setup Guide
EN
RIVAGE PM7 System Setup Guide
2
Explanation of Graphical Symbols
Explication des symboles
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une
« tension dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions
importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.
IMPORTANT SAFETY
INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
(UL60065_03)
PRÉCAUTIONS CONCER-
NANT LA SÉCURITÉ
1 Lire ces instructions.
2 Conserver ces instructions.
3 Tenir compte de tous les avertissements.
4 Suivre toutes les instructions.
5 Ne pas utiliser ce produit à proximité d’eau.
6 Nettoyer uniquement avec un chiffon propre et sec.
7 Ne pas bloquer les orifices de ventilation. Installer l’appareil
conformément aux instructions du fabricant.
8 Ne pas installer l’appareil à proximité d’une source de chaleur
comme un radiateur, une bouche de chaleur, un poêle ou tout autre
appareil (y compris un amplificateur) produisant de la chaleur.
9 Ne pas modifier le système de sécurité de la fiche polarisée ou de
la fiche de terre. Une fiche polarisée dispose de deux broches dont
une est plus large que l’autre. Une fiche de terre dispose de deux
broches et d’une troisième pour le raccordement à la terre. Cette
broche plus large ou cette troisième broche est destinée à assurer
la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas
compatible avec les prises de courant disponibles, faire remplacer
les prises par un électricien.
10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas
piétinés ni coincés, en faisant tout spécialement attention aux
fiches, prises de courant et au point de sortie de l’appareil.
11 Utiliser exclusivement les fixations et accessoires spécifiés par le
fabricant.
12 Utiliser exclusivement le chariot, le stand, le
trépied, le support ou la table recommandés par
le fabricant ou vendus avec cet appareil. Si
l’appareil est posé sur un chariot, déplacer le
chariot avec précaution pour éviter tout risque
de chute et de blessure.
13 Débrancher l’appareil en cas d’orage ou lorsqu’il
doit rester hors service pendant une période prolongée.
14 Confier toute réparation à un personnel qualifié. Faire réparer
l’appareil sil a subi tout dommage, par exemple si la fiche ou le
cordon d’alimentation est endommagé, si du liquide a coulé ou des
objets sont tombés à l’intérieur de l’appareil, si l’appareil a été
exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas
normalement ou est tombé.
(UL60065_03)
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ATTENTION :
POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER
LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT
L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,
FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
ATTENTION
RISQUE DE CHOC
ELECTRIQUE-NE PAS OUVRIR
The above warning is located on the rear of the unit. Lavertissement ci-dessus est situé sur l’arrière de l’unité.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE
ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À
L’HUMIDITÉ.
RIVAGE PM7 System Setup Guide
3
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reason-
able level of assurance that your use of this product in a residential
environment will not result in harmful interference with other elec-
tronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
(class B)
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to elimi-
nate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
90620
Telephone : 714-522-9011
Type of Equipment : DIGITAL MIXING CONSOLE
Model Name : CSD-R7
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interfer-
ence that may cause undesired operation.
See user manual instructions if interference to radio reception is sus-
pected.
(FCC DoC)
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning
må kun ske med batteri af samme fabrikat og type. Levér det brugte
batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller
en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty
paristo valmistajan ohjeiden mukaisesti.
(lithium caution)
NEDERLAND / THE NETHERLANDS
Dit apparaat bevat een lithium batterij voor geheugen back-up.
This apparatus contains a lithium battery for memory back-up.
Raadpleeg uw leverancier over de verwijdering van de batterij op het
moment dat u het apparaat ann het einde van de levensduur of gelieve
dan contact op te nemen met de vertegenwoordiging van Yamaha in
uw land.
For the removal of the battery at the moment of the disposal at the end
of life please consult your retailer or Yamaha representative office in
your country.
Gooi de batterij niet weg, maar lever hem in als KCA.
Do not throw away the battery. Instead, hand it in as small chemical
waste.
(lithium disposal)
This product contains a battery that contains perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
(Perchlorate)
이 기기는 가정용(B급) 전자파적합기기로서 주로
가정에서 사용하는 것을 목적으로 하며, 모든
지역에서 사용할 수 있습니다.
(class b korea)
RIVAGE PM7 System Setup Guide
4
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe place for
future reference.
WARNING
Always follow the basic precautions listed below to avoid
the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other
hazards. These precautions include, but are not limited
to, the following:
Power supply/power cord
Do not place the power cord near heat sources such as
heaters or radiators, and do not excessively bend or otherwise
damage the cord, place heavy objects on it, or place it in a
position where anyone could walk on, trip over, or roll anything
over it.
Only use the voltage specified as correct for the device. The
required voltage is printed on the name plate of the device.
Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one
you purchased, the included power cord may not be
compatible. Please check with your Yamaha dealer.
Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
When setting up the device, make sure that the AC outlet you
are using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the outlet. Even when the power switch is turned
off, as long as the power cord is not unplugged from the wall
AC outlet, the device will not be disconnected from the power
source.
Remove the electric plug from the outlet when the device is
not to be used for extended periods of time, or during
electrical storms.
Be sure to connect to an appropriate outlet with a protective
grounding connection.
Do not open
This device contains no user-serviceable parts. Do not open
the device or attempt to disassemble the internal parts or
modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Water warning
Do not expose the device to rain, use it near water or in damp
or wet conditions, or place on it any containers (such as
vases, bottles or glasses) containing liquids which might spill
into any openings. If any liquid such as water seeps into the
device, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the device inspected by
qualified Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Hearing loss
Avoid setting all equalizer controls and faders to their
maximum. Depending on the condition of the connected
devices, doing so may result in feedback that can cause
hearing loss and damage the speakers.
Do not use headphones for a long period of time at a high or
uncomfortable volume level, since this can cause permanent
hearing loss. If you experience any hearing loss or ringing in
the ears, consult a physician.
Before connecting the device to other devices, turn off the
power for all devices. Also, before turning the power of all
devices on or off, make sure that all volume levels are set to
the minimum. Failing to do so may result in hearing loss,
electric shock, or device damage.
When turning on the AC power in your audio system, always
turn on the power amplifier LAST, to avoid hearing loss and
speaker damage. When turning the power off, the power
amplifier should be turned off FIRST for the same reason.
Fire warning
Do not place any burning items or open flames near the
device, since they may cause a fire.
If you notice any abnormality
If any of the following problems occur, immediately turn off the
power switch and disconnect the electric plug from the outlet.
- The power cord or plug becomes frayed or damaged.
- Unusual smells or smoke are emitted.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
- Cracks or other visible damage appear on the device.
Then have the device inspected or repaired by qualified
Yamaha service personnel.
If this device should be dropped or damaged, immediately
turn off the power switch, disconnect the electric plug from the
outlet, and have the device inspected by qualified Yamaha
service personnel.
CAUTION
Always follow the basic precautions listed below to avoid
the possibility of physical injury to you or others, or
damage to the device or other property. These
precautions include, but are not limited to, the following:
Power supply/power cord
When removing the electric plug from the device or an outlet,
always hold the plug itself and not the cord. Pulling by the
cord can damage it.
To disconnect the device from the mains, unplug both power
cords.
Shock hazard
Disconnect all power sources.
This device receives power from multi
sources. When setting up the device, make
sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction
occurs, immediately turn off the power switch
and disconnect the all plugs from the outlet.
Even when the power switch is turned off, as
long as the power cord is not unplugged from
the wall AC outlet, the device will not be
disconnected from the power source.
PA_en_8 1/3
RIVAGE PM7 System Setup Guide
5
Location
Do not place the device in an unstable position where it might
accidentally fall over and cause injuries.
Do not block the vents. This device has ventilation holes at the
rear/under the front to prevent the internal temperature from
becoming too high. In particular, do not place the device on
its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or
even fire.
Do not place the device in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
Avoid being near the device during a disaster, such as an
earthquake. Since the device may turn over or fall and cause
injury, stay away from the device quickly and move to a safe
place.
Before moving the device, remove all connected cables.
When transporting or moving the device, always use four or
more people. This device must be lifted by a group of four or
more people. Otherwise, personal injuries, such as back or
shoulder injuries, or damage to the device may result.
Keep device away from the reach of children.
Maintenance
Remove the power plug from the AC outlet when cleaning the
device.
Handling caution
Do not insert your fingers or hands in any gaps or openings on
the device (vents, panel, etc.).
Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device (vents,
panel, etc.) If this happens, immediately turn off the power,
unplug the power cord from the AC outlet, and have the
device inspected by qualified Yamaha service personnel.
Do not rest your weight on the device or place heavy objects
on it. Avoid applying excessive force to the buttons, switches
or connectors to prevent injuries.
Avoid pulling the connected cables to prevent injuries or
damage to the device by causing it to fall.
Backup battery
Do not replace the backup battery by yourself. Doing so may
cause an explosion and/or damage to the device(s).
If the backup battery power is fully depleted, contact your
Yamaha dealer and have qualified Yamaha service personnel
replace the backup battery.
NOTICE
To avoid the possibility of malfunction/ damage to the
product, damage to data, or damage to other property,
follow the notices below.
Handling and maintenance
Do not use the device in the vicinity of a TV, radio, AV
equipment, mobile phone, or other electric devices.
Otherwise, the device, TV, or radio may generate noise.
Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a heater,
or in a car during the day), in order to prevent the possibility of
panel disfiguration, unstable operation, or damage to the
internal components.
Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
Condensation can occur in the device due to rapid, drastic
changes in ambient temperature—when the device is moved
from one location to another, or air conditioning is turned on or
off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that
condensation might have occurred, leave the device for
several hours without turning on the power until the
condensation has completely dried out.
During extreme changes in temperature or humidity,
condensation may occur and water may collect on the surface
of the device. If water is left, the wooden parts may absorb the
water and be damaged. Make sure to wipe any water off
immediately with a soft cloth.
Do not apply oil, grease, or contact cleaner to the faders.
Doing so may cause problems with electrical contact or fader
motion.
Even when the [ ] (Standby/On) switch is in standby status
(power lamp is off/ display is off), electricity is still flowing to
the instrument at the minimum level. When you are not using
the instrument for a long time, make sure you unplug the
power cord from the wall AC outlet.
Saving data
This device has a built-in backup battery that maintains clock
data even when the device’s power is switched off. The
backup battery will eventually become depleted, however,
and when that happens the clock data will be lost. To prevent
loss of data be sure to replace the backup battery before it
becomes fully depleted. If you need to replace the backup
battery, then have qualified Yamaha service personnel replace
the backup battery. The average life of the internal backup
battery is approximately 5 years, depending on operating
conditions.
Make sure that the front end
of the table will remain under
the front stabilizer legs.
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the device, or data that is
lost or destroyed.
PA_en_8 2/3
RIVAGE PM7 System Setup Guide
6
Connectors
XLR-type connectors are wired as follows (IEC60268 standard):
pin 1: ground, pin 2: hot (+), and pin 3: cold (–).
Information
About copyrights
Copying of the commercially available musical data including
but not limited to MIDI data and/or audio data is strictly
prohibited except for your personal use.
About functions/data bundled with the product
Supply of this product does not convey a license nor imply
any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite,
cable and/or other distribution channels), streaming
applications (via Internet, intranets and/or other networks),
other content distribution systems (pay-audio or audio-
ondemand applications and the like) or on physical media
(compact discs, digital versatile discs, semiconductor chips,
hard drives, memory cards and the like). An independent
license for such use is required. For details, please visit
http://mp3licensing.com.
About this manual
The illustrations and LCD screens as shown in this manual are
for instructional purposes only.
Windows is a registered trademark of Microsoft
®
Corporation
in the United States and other countries.
Apple, Mac, Macintosh, and iPad are trademarks of Apple
Inc., registered in the U.S. and other countries.
The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
Software may be revised and updated without prior notice.
(rear_en_01)
(weee_eu_en_02)
European models
Purchaser/User Information specified in EN55103-2:2009.
Conforms to Environments: E1, E2, E3 and E4
The model number, serial number, power requirements, etc., may
be found on or near the name plate, which is at the rear of the
unit. You should note this serial number in the space provided
below and retain this manual as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
Information for users on collection and disposal of old
equipment:
This symbol on the products, packaging, and/or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste. For proper
treatment, recovery and recycling of old
products, please take them to applicable
collection points, in accordance with your
national legislation.
By disposing of these products correctly, you will help to save
valuable resources and prevent any potential negative effects on
human health and the environment which could otherwise arise
from inappropriate waste handling.
For more information about collection and recycling of old
products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased the
items.
For business users in the European Union:
If you wish to discard electrical and electronic equipment, please
contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European
Union:
This symbol is only valid in the European Union. If you wish to
discard these items, please contact your local authorities or
dealer and ask for the correct method of disposal.
PA_en_8 3/3
RIVAGE PM7 System Setup Guide
7
Introduction ............................8
Main Features ................................... 8
About manuals.................................. 8
About utility software........................ 9
Firmware updates ............................. 9
Conventions in this manual............... 9
Accessories........................................ 9
System Overview....................10
Introducing the devices................... 10
About network card ........................ 11
About Dante ..........................12
Caution when using a
network switch................................ 12
About Connections ................12
Daisy Chain Network ...................... 12
Star Network................................... 13
Part Names & Functions ........14
Top panel ....................................... 14
Front panel .................................... 26
Rear panel ...................................... 27
Power Supply .........................30
Connecting to power sources.......... 30
Installing and Removing
Optional Cards .....................30
Installing a Mini-YGDAI card ........... 30
Removing the Mini-YGDAI card....... 31
Installing an HY card ....................... 31
Removing an HY Card ..................... 32
Touch Screen .........................33
Basic touch screen operations ......... 33
On-screen user interface.................. 33
Viewing a touch screen ................... 34
Quick Guide ...........................35
Basic system configuration ............. 35
Installing an optional card ............... 35
Setting the Unit ID .......................... 36
Connecting the devices................... 37
Turning on the power to
the RIVAGE PM7 system ..................37
Setting the word clock .................... 38
Assigning channels to the
TWINLANe network ........................ 38
Patching the input ports.................. 40
Patching the output ports ............... 41
Setting the analog gain for HA
(Head Amp) .................................... 42
Sending an input channel signal to
the STEREO bus............................... 42
Check list ........................................ 44
Other Operations...................45
Initializing the unit to
factory default settings .................... 45
Adjusting the faders
(Calibration function) ...................... 45
Troubleshooting ....................47
Specifications ........................48
General Specifications ..................... 48
Pin Assignment Table ...................... 52
Dimensional Diagrams .................... 53
Index......................................54
Contents
RIVAGE PM7 System Setup Guide
8
Thank you for purchasing the Yamaha RIVAGE PM7
digital mixing system. This product is suitable for the use
in a large-scale hall or event. This manual provides the
information and procedures required for audio
installation companies to plan and set up the audio
system. It also describes the set-up procedure and basic
operation for mixing engineers. In order to take full
advantage of this systems superior functionality and enjoy
years of trouble-free use, please read this manual before
you use the product. After you have read the manual, keep
it in a safe place for future reference.
Main Features
The RIVAGE PM7 system features superb sound quality,
intuitive controls, and innovative functionality. It is a
state-of-the-art mixing system that supports a variety of
applications.
Superb sound quality
The design of the RIVAGE PM7 digital mixing system is
an uncomprised expression of Yamahas philosophy of Pro
Audio device design. This philosophy is called “white
canvas,” and suggests that the ideal starting point for sonic
creativity is pure, natural reproduction achieved through
the use of high quality analog circuits. Only then can
sound be colored effectively by a variety of aural paints for
the desired creative impact. Numerous processing options
(such as plug-ins, SILK, etc.) enable powerful sound
production capabilities in the digital domain. Through a
fusion of analog and digital technologies, the RIVAGE
PM7 has achieved both the creation of a pure, transparent
sound, and fluid capabilities for coloring that sound.
Intuitive controls
The RIVAGE PM7 features a farther advanced top panel
controls, including large touch panel screens, a full
implementation of Yamahas acclaimed Selected Channel
interface, and highly user-friendly USER DEFINED
KEYS/KNOBS section and TOUCH AND TURN knobs.
This feature provides the systems extraordinary
operability.
Innovative functionality
The RIVAGE PM7 also features abundant inputs and
outputs; flexible signal routing; powerful DSP processing
with two insert points; and scene memory and library
management that supports an enormous amount of
sophisticated requirements. The system also provides
numerous benefits for users by maintaining reliability
through power and network redundancy.
These core features are supported by state-of-the-art
technologies and an advanced level of product reliability
that have been cultivated through years of experience in
developing digital mixing consoles, such as the PM1D and
PM5D. The deep passion of Yamahas engineering team
has been infused into the RIVAGE PM7.
About manuals
•RIVAGE PM7 System Setup Guide (this book)
This guide describes an overview of the RIVAGE PM7
system, and explains step by step how to set up the
system from connecting devices to producing sound.
This guide also serves as a user guide for the CSD-R7.
It explains part names and panel functions.
Manuals for other devices
The manuals for other devices describe part names and
functions of the corresponding devices.
These manuals are supplied with the corresponding
device packages.
•RIVAGE PM Operation Manual
The Operation Manual provides detailed explanations
of all screens and functions, and includes step-by-step
procedures to help you operate the RIVAGE PM series.
RIVAGE PM Editor Installation Guide
This guide describes how to install the RIVAGE PM
Editor.
•RIVAGE PM StageMix User Guide
This guide describes an iPad application that enables
you to control the RIVAGE PM series system
wirelessly.
Using the PDF manuals
These manuals are electronic files in PDF format. You
can read this book on a computer. Use Acrobat Reader
to read this book on screen, search for words very
quickly, print specific pages, or click links to display
sections of special interest. The ability to search for
words, or to follow links directly to relevant sections in
the document, are helpful attributes of this electronic
file format. We encourage you to take advantage of
these benefits.
You can download the latest Acrobat Reader
application from the website listed below.
http://www.adobe.com/
All manuals can be downloaded from the Yamaha website.
If necessary, you can review updated manual information,
which is always posted in the Yamaha website.
http://download.yamaha.com/
Introduction
RIVAGE PM7 System Setup Guide
9
About utility software
The RIVAGE PM7 system can be used with a variety of
utility software.
•RIVAGE PM Editor
This application software enables you to access the
same functions that are available on a digital mixing
console. You can use your computer to perform off-
line editing by preparing the RIVAGE PM7 system
settings in advance, and later, to monitor and adjust
those settings (on-line monitoring/operation).
•RIVAGE PM StageMix
StageMix enables you to use your iPad to wirelessly
control the parameters of your Yamaha RIVAGE PM
series digital mixing console. StageMix offers the
sound engineer (who is away from the system) the
freedom to control parameters remotely, while
listening to the results from the vantage point of the
performers.
Information on these software applications is available
on the Yamaha Pro Audio website:
http://www.yamaha.com/proaudio/
For information regarding how to download or install
Editor or StageMix, as well as their various setting
details, please refer to the website listed above or to the
Installation Guide attached to the downloaded
software program.
Firmware updates
You can update the unit firmware to improve operations,
add functions, and correct possible malfunctions.
Details on updating the firmware are available on the
following Yamaha Pro Audio website:
http://www.yamaha.com/proaudio/
For information on updating and setting up the unit,
please refer to the firmware update guide available on the
website.
Conventions in this manual
In this manual, switch-type controllers on the panel are
called “keys.” Control knobs on the panel are called
“knobs.” Some knobs rotate from a minimum value to a
maximum value, while others rotate endlessly.
Virtual buttons displayed on the screen are called
“buttons, and virtual knobs are called “knobs.
Controls located on the panel are enclosed in square
brackets [ ] (e.g., [CUE] key) to distinguish them from
virtual buttons and knobs displayed on screen. For certain
controls, the name of the section appears before the
brackets (e.g., Selected Channel [ISOLATE] key).
Accessories
•AC Power Cords (×2)
(The connector shape may vary depending on the sales
area.)
•Dust cover
Gooseneck Lamps LA1L (×4)
•System Setup Guide (this book)
RIVAGE PM7 System Setup Guide
10
Introducing the devices
The RIVAGE PM7 system consists of the following components:
NOTE
Please refer to the owners manual supplied with the host device for information on installing the I/O cards.
For detailed information on I/O card settings, refer to the owner’s manual for the I/O card.
For the latest information on which I/O cards can be used with the system, visit the Yamaha Pro Audio website at:
http://www.yamaha.com/proaudio/
System Overview
Digital mixing console I/O racks
RPio622
RPio222
The control surfaces enable you to perform general operations on the
RIVAGE PM7 system.
The I/O racks input and output analog and digital audio
signals.
RY cards HY cards
RY16-ML-SILK
This is a 16-channel mic/line input card.
It features SILK digital processing technology that has been co-developed
by Rupert Neve Designs and Yamaha.
RY16-DA
This card features 16-channel analog outputs.
RY16-AE
This card features 16-channel digital I/Os that support the AES/EBU format.
A sampling rate converter is built in for both inputs and outputs.
HY256-TL
HY256-TL-SMF
This digital I/O card supports TWINLANe (Yamaha’s
proprietary audio transfer network protocol). It can handle
256 channels and be installed in the HY card slot.
HY256-TL uses multimode fiber optic cables. HY256-TL-
SMF uses singlemode fiber optic cables.
HY144-D
This digital I/O card supports the Dante digital audio
network. It can handle 144 channels and be installed in
the HY card slot.
RIVAGE PM7 System Setup Guide
11
TWINLANe network
TWINLANe is Yamahas proprietary audio transfer
network protocol. With this protocol, 400-channel digital
audio and control signals can be transfered via a single
cable simultaneously.
To connect devices, first install a TWINLANe network
card in an HY card slot of each device, then use fiber optic
cables to connect the TWINLANe network cards in a ring
network topology.
* If the number of connected devices is much larger, or if the
total length of all cables is too long, the listed value may not
apply.
NOTE
Yamaha recommends that you use opticalCON DUO fiber cable
made by Neutrik. In general, fiber optic cables are susceptible to
bending or pulling. Use a fiber optic cable that features a strong
plastic jacket and lock mechanism to avoid cable-related
problems.
About cleaning
If dirt or dust attached to the contact surface of jacks on
the fiber optic cables or connectors on the device, data
may not be transferred properly. Clean the contact surface
of jacks and connectors regularly using a commercially-
available fiber optic cleaning tool.
Ring connection
A TWINLANe network uses a ring topology, which
provides redundancy in case of broken cables. If a cable in
the network breaks down for some reason, the signal will
be automatically re-routed and audio will flow without
interruption. Even if a device in the network malfunctions,
other working devices will be able to continue
communicating.
Normal situation
When a cable is broken
About network card
The RIVAGE PM7 system uses an TWINLANe network
card to configure the I/O network.
* Total cable length for the ring connection using TWINLANe
cards can span up to 6 kilometers.
Transferred data 400-channel audio signal and control
signal
Sampling frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Network latency* 11 sample@Fs= 44.1 kHz (0.25 msec)
11 sample@Fs= 48 kHz (0.23 msec)
12 sample@Fs= 88.2 kHz (0.14 msec)
12 sample@Fs= 96 kHz (0.13 msec)
Bit-length 32-bit
Topology Ring
.....
INOUT NINIOUT OUT
Device
TWINLANe
Network Card
Device
TWINLANe
Network Card
Device
TWINLANe
Network Card
TWINLANe network
card
HY256-TL HY256-TL-SMF
Connection cable Multimode fiber
optic cable
Singlemode fiber
optic cable
Maximum cable length
between devices
Max. 300m Max. 2km*
Maximum number of
channels
256-in/256-out
INOUT INOUT INOUT
INOUT INOUT INOUT
Even if a cable is severed at one point, the
signal will be re-routed automatically and
communication will continue without
interruption.
RIVAGE PM7 System Setup Guide
12
Dante is a network audio protocol developed by the
Audinate. Within a Giga-bit Ethernet (GbE), Dante
delivers multi-channel audio signals at various sampling
frequencies and bit rates, as well as device control signals.
Visit the Audinate website for more details on Dante.
http://www.audinate.com/
More information on Dante is also posted on the Yamaha
Pro Audio website:
http://www.yamaha.com/proaudio/
Caution when using a
network switch
Please do not use the EEE function (*) of network switches
in a Dante network.
Although power management should be negotiated
automatically in switches that support EEE, some switches
do not perform the negotiation properly.
This may cause EEE to be enabled in Dante networks
when it is not appropriate, resulting in poor
synchronization performance and occasional dropouts.
Therefore we strongly recommend the following:
When using a managed switch, turn off the EEE
function of all ports used by Dante. Do not use a
switch that is unable to turn off the EEE function.
If using an unmanaged switch, do not use a switch that
supports the EEE function. Such switches are unable to
turn off the EEE function.
* EEE (Energy Efficient Ethernet) is a technology that reduces switch
power consumption during periods of low network traffic. It is also
known as Green Ethernet or IEEE802.3az.
There are two ways to connect the Rio to a Dante network.
Please refer to the Operation Manual and other related
documents for more information on how to set up and
and connect your Dante-enabled devices.
NOTE
A daisy chain connection is suitable for a simple system with a
small number of devices.
Use a star network if a large number of devices are connected.
Daisy Chain Network
A daisy chain is a wiring scheme in which multiple devices
are connected together in sequence. In this way,
networking is simple and requires no network switches.
If you connect a large number of devices, you must set a
higher latency value to avoid skipping audio that could be
caused by an increased delay in signal transfer among the
devices. Also, if a connection is broken in a daisy chain
network, the signal flow is interrupted at that point and no
signal will be transferred beyond that point.
About Dante About Connections
Rio3224-D2 (UNIT ID: Y001)
Rio3224-D2 (UNIT ID: Y002)
SECONDARY
PRIMARY
PRIMARY
CSD-R7
HY144-D
RIVAGE PM7 System Setup Guide
13
Star Network
In a star network, each device is connected to a central
network switch. Using a GbE-compatible network switch
enables you to configure a wide-band, large-scale network.
We recommend a network switch that features various
functions to control and monitor the network (such as
Qos, the ability to assign priority to data flows - e.g., clock
synchronization or audio transmission on certain data
circuits.)
With this topology, it is common to configure a redundant
network so that an unexpected network problem will not
affect any audio or otherwise stable communications.
About Redundant Networks
A redundant network consists of two circuits, a primary
circuit and a secondary circuit. Normally, the network
operates on the primary circuit. However, if the primary
connection is broken, the secondary circuit will
automatically take over communications. Therefore, using
a redundant network with a star topology would increase
communication stability relative to a daisy chain network.
NOTE
If you have been using an HY144-D card on RIVAGE PM10
V1.51 or earlier, you must update the firmware for the HY144-D.
Details on updating the firmware are available on the following
Yamaha Pro Audio website:
http://www.yamaha.com/proaudio/
CSD-R7
HY144-D
SECONDARY
SECONDARY
SECONDARYPRIMARY
PRIMARY
PRIMARY
Rio3224-D2 (UNIT ID: Y001)
Rio3224-D2 (UNIT ID: Y002)
RIVAGE PM7 System Setup Guide
14
Top panel
A Touch Screen section page 22
B Channel Strip section page 23
C Selected Channel section page 15
D UTILITY section page 19
E SCENE MEMORY section page 20
F USER DEFINED KEYS/KNOBS section page 21
Part Names & Functions
A
B
CD
FB
E
RIVAGE PM7 System Setup Guide
15
Selected Channel section
This section enables you to adjust parameters for the selected channel.
[ISOLATE] key
Switches Isolate on or off. The Isolate function
enables you to protect the channel from any recall
operations for scenes or libraries. Also, if the
“isolated” channel belongs to any DCA, Mute group,
or other category, the channel will be unaffected by
the controls of that group.
[RCL SAFE] key
Switches Recall Safe on or off.
The Recall Safe function protects certain parameters
of a channel from scene recall operations.
[MUTE SAFE] key
Switches Mute Safe on or off.
The Mute Safe function protects a channel from mute
operations.
TO ST [A]/[B] keys
Switch on or off the signal sent from the input
channel to stereo bus A or B.
Meter LEDs
Displays the channel signal level.
[CUE] key
Switches channel cue send on or off.
RIVAGE PM7 System Setup Guide
16
[PAN/BAL] knob
Sets the panning/balance of the signal sent to the
stereo buses.
[Fn] (Function) key
Executes the pre-assigned function.
[ON] key
Switches the channel on or off.
[FADER] knob
Adjusts the channel fader level.
[COPY] key
Copies a channel parameter.
[PASTE] key
Pastes the copied channel parameter.
Channel name display
Indicates the channel number and name, fader value,
etc.
Channel color indicator
Indicates the channel color.
[INC]/[DEC] keys
Switch channels to edit parameters.
INPUT/A.GAIN/SILK/D.GAIN/DELAY
INPUT [A]/[B] keys
Switch the input source for the selected input
channel.
[ANALOG GAIN] knob
Sets the analog gain for the head amp.
[+48V] key
Switches phantom power (+48V) on or off.
SILK [TEXTURE] knob
Adjusts the intensity of SILK processing.
SILK [ON] key
Switches SILK on or off.
SILK processing can be applied only to specific
channels to bring the corresponding parts to life
within the mix, or to all channels to add depth and
perspective to the mix overall.
SILK [BLUE/RED] key
Toggles between BLUE and RED: “BLUE” for solidity
and power, and “RED” for sparkling energy.
[DIGITAL GAIN] knob
Sets the digital gain of the channel.
GC indicator
Lights up when GC (GAIN COMPENSATION) is
enabled.
[ ] (Phase) key
Reverses the phase of the input signal.
DELAY [ON] key
Switches Delay on or off.
DELAY display
Indicates the delay value.
[DELAY] knob
Sets the delay value.
RIVAGE PM7 System Setup Guide
17
EQUALIZER
EQUALIZER [1-4]/[(5-8)] keys
Switch the EQ bands for which you want to make
settings.
Pressing both [1-4] and [5-8] keys simultaneously
will set the gain for all bands to 0 (FLAT).
EQUALIZER [ON] key
Switches EQ on or off.
EQUALIZER [SHELF] key
Switches peaking filter to shelving filter.
EQUALIZER display
Indicates parameters for each EQ band.
EQUALIZER [Q] knob
Specifies the Q value.
EQUALIZER [FREQUENCY] knob
Sets the frequency.
EQUALIZER [GAIN] knob
Sets the gain.
LPF/HPF
LPF/HPF [FREQUENCY] knobs
Specify the cutoff frequency of LPF and HPF
respectively.
LPF/HPF display
Indicates the LPF and HPF settings.
LPF/HPF [ON] keys
Switch the LPF and HPF on or off respectively.
LPF/HPF [SLOPE] keys
Switch the LPF and HPF slope settings respectively.
DCA/MUTE/INSERT
DCA ASSIGN LEDs
Indicate the assigned DCAs.
MUTE GROUP ASSIGN LEDs
Indicate the assigned Mute Groups.
INSERT [PLUG-INS] key
Enables you to recall a parameter setting screen for
the inserted plug-ins.
INSERT 1/2 [ON] keys
Switch the INSERT1 and INSERT2 on or off
respectively.
RIVAGE PM7 System Setup Guide
18
DYNAMICS
DYNAMICS 1/2 IN LEDs
Indicates the Dynamics input level.
DYNAMICS 1/2 GR LEDs
Indicates the amount of Dynamics gain reduction.
DYNAMICS 1/2 [<]/[>] keys
Switch parameters that are indicated on the
DYNAMICS display.
DYNAMICS 1/2 setting knobs
Set parameters that are indicated on the DYNAMICS
display.
DYNAMICS 1/2 display
Indicates the Dynamics parameters.
DYNAMICS 1/2 [ON] key
Switches Dynamics on or off.
MIX/MATRIX SENDS
MIX/MATRIX knobs
Adjust the send levels for the corresponding buses.
MIX/MATRIX SENDS [PRE] keys
Toggle the send point between PRE and POST. If a
key lights up, the send point is set to PRE.
MIX/MATRIX SENDS [ON] keys
Switch the send signal to the corresponding bus on or
off.
MIX/MATRIX SENDS display
Indicates the corresponding bus.
MIX/MATRIX SENDS [MIX]/[MATRIX] keys
Switch the type of the send destination bus.
MIX/MATRIX SENDS [1-12]/[13-24]/[25-36]/
[37-48]/[49-60] keys
Selects a bank for the send destination bus.
RIVAGE PM7 System Setup Guide
19
UTILITY section
POWER Indicator
Lights when AC power to the unit is ON. If both
power switches A and B are turned on, this indicator
will light green. If either power switch A or B is
turned on, it will light red. If the RIVAGE PM7
system is not started, it will light orange.
USB port
Enables you to connect a USB device (such as a
mouse, keyboard, or USB flash drive). Use a USB
flash drive to store the systems internal data and to
load the stored data into the system.
Supported USB flash drive format
The FAT16 and FAT32 formats are supported.
Write Protection
Some USB flash drives feature write protection that
prevents data from being erased inadvertently.
If your USB flash drive contains important data, we
suggest that you use write protection to prevent
accidental erasure.
On the other hand, you will need to make sure that
your USB flash drives write-protect setting is turned
off before you save data onto the USB flash drive.
For the latest information on which USB flash drives
can be used with the system, visit the Yamaha Pro
Audio website at:
http://www.yamaha.com/proaudio/
NOTICE
Do not remove the USB flash drive from the USB
connector or turn off the power to the unit while the unit is
accessing data, e.g., saving, loading or deleting data.
Doing so may damage your flash drive, or may damage the
data in the unit or on your media device.
RECORDING port
Enables you to connect a USB flash drive to record
and play back audio files. Supported file formats
include WAV and MP3.
For the latest information on what USB flash drives
can be used with the system, visit the Yamaha Pro
Audio website at:
http://www.yamaha.com/proaudio/
[SYSTEM] key
Press this key to display information about the
RIVAGE PM7 system on the touch screens.
Press and hold down the key for two seconds or
longer to shut down the control section of the console
( page 29). Be sure to shut down before turning off
the power to the unit.
TALKBACK jack
This is a balanced XLR-3-31 jack to which a talkback
mic can be connected.
+48V indicator
Lights up when +48V phantom power is supplied to
the TALKBACK jack.
TALKBACK [LEVEL] knob
Adjusts the input level of the mic connected to the
TALKBACK jack.
TALKBACK [ON] key
Switches the Talkback function on or off.
MONITOR A/B [LEVEL] knobs
Adjust the output level of the monitoring signals.
RIVAGE PM7 System Setup Guide
20
SCENE MEMORY section
[OVERLAY] key
Press this button to display the OVERLAY SETTING
screen.
While pressing and holding down the [SHIFT] key,
press the [OVERLAY] key to switch Overlay on or
off.
While Overlay is turned on, press and hold down the
[OVERLAY] key to enter Overlay edit mode.
[UNDO] key
Cancels the most recent scene operation of storing,
recalling or updating a scene.
After you cancel the operation by pressing the [UNDO]
key, you can “redo” the canceled operation by pressing
the [UNDO] key again.
NOTE
You cannot undo an operation to store a new scene.
[UPDATE] key
Updates scene data by overwriting the current scene
(that has been recalled most recently) with the
current mix data.
SCENE MEMORY display
Indicates the selected scene memory.
[PREVIEW] key
Switches Preview mode on or off.
[STORE] key
Stores the current scene settings to the selected scene
memory. If you select the existing scene, it will be
overwritten.
[INC]/[DEC] keys
Enable you to select the scene number of a scene that
you want to store or recall.
[RECALL] key
Enables you to recall a stored scene from scene
memory.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Yamaha Pm7 Asennusohje

Kategoria
Audio equalizers
Tyyppi
Asennusohje