Yamaha NP-11 Omistajan opas

Brändi: Yamaha

Malli: NP-11

Kategoria: Digital pianos

Tyyppi: Omistajan opas

Tämä käsikirja sopii myös

NP-31

Owner’s Manual

NP-31/NP-11 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

WARNING:

Do not place this product in a position where anyone could

walk on, trip over, or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use an

extension cord, the minimum wire size for a 25’ cord (or less) is 18 AWG.

NOTE: The smaller the AWG number, the larger the current handling

capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change or

modify any of the specifications without notice or obligation to update

existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be dealer

assembled or installed. Please make sure that benches are stable and

any optional fixtures (where applicable) are well secured BEFORE

using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are

not covered by the manufacturer’s warranty, and are therefore the

owners responsibility. Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and envi-

ronmentally friendly. We sincerely believe that our products and the

production methods used to produce them, meet these goals. In keep-

ing with both the letter and the spirit of the law, we want you to be

aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately five years. When replacement becomes necessary,

contact a qualified service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, never mix old batteries with new ones, and

never mix different types of batteries. Batteries MUST be installed cor-

rectly. Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all bat-

teries away from children. Dispose of used batteries promptly and as

regulated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some rea-

son its useful life is considered to be at an end, please observe all

local, state, and federal regulations that relate to the disposal of prod-

ucts that contain lead, batteries, plastics, etc. If your dealer is unable

to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this manual

as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

NP-31/NP-11 Owner’s Manual

About the Manuals................................................ 4

Accessories .......................................................... 4

PRECAUTIONS.................................................... 5

Introduction

Setting Up 7

Power Requirements ............................................ 7

Connecting Headphones or an Audio Device

(PHONES/OUTPUT Jack) ............................... 8

Connecting a Footswitch or a Foot Pedal

(SUSTAIN Jack) .............................................. 8

Turning the Power On .......................................... 8

Auto Power Off Function ...................................... 8

Using the Music Rest............................................ 8

Panel Controls and Terminals 9

Reference

Selecting & Playing Voices 10

Selecting Voices................................................. 10

Combining Voices (Dual).................................... 11

Listening to the Voice Demo Songs 12

Listening to the Piano Demo Songs 13

Using the Metronome 14

Other Settings 16

Adding Variations to the Sound – Reverb .......... 16

Transposing the Pitch......................................... 17

Fine Tuning of the Pitch...................................... 17

Touch Sensitivity ................................................ 18

Disabling the Auto Power Off Function............... 18

Connecting MIDI Instruments 19

Connecting to the MIDI [IN] [OUT] terminals ...... 19

MIDI Capabilities ................................................ 19

MIDI Functions 20

Troubleshooting 21

Optional Equipment 21

Appendix

Specifications 22

Index 23

Table of Contents

NP-31/NP-11 Owner’s Manual

Thank you for purchasing the Yamaha digital keyboard!

We recommend that you read this manual carefully so that

you can fully take advantage of the advanced and convenient

functions of the instrument.

We also recommend that you keep this manual in a safe and

handy place for future reference.

This instrument has the following documents and instructional materials.

 Included Documents

Owner’s Manual (this book)

This Owner’s Manual describes how to use the functions of the instrument.

Before using the instrument, be sure to read the Precautions on pages 5 – 6.

Quick Operation Guide

This Quick Operation Guide shows and explains in chart form the operation of the functions assigned

to the buttons and the keyboard for quick and easy understanding.

 Online Materials (downloadable from the web)

The following instructional materials are available for downloading from the Yamaha website.

Yamaha Manual Library http://www.yamaha.co.jp/manual/

Access the Yamaha Manual Library, then enter your model name (NP-31, for example) in the Model Name area

to search for a specific manual.

MIDI Reference

This contains the MIDI Data Format, the MIDI Implementation chart and detailed explanations about

the MIDI settings of the instrument.

MIDI Basics (only in English, French, German and Spanish)

If you want to know more about MIDI and how to use it, refer to this introductory book.

• Owner’s Manual

• Quick Operation Guide

• Music Rest

• AC Power Adaptor

* May not be included depending on your particular area.

Please check with your Yamaha dealer.

• My Yamaha Product User Registration

* The PRODUCT ID on the sheet will be needed when you fill out the User Registration form.

About the Manuals

Accessories

NP-31/NP-11 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-

circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on it,

or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use the specified adaptor (page 22) only. Using the wrong adaptor can result in

damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as water

seeps into the instrument, turn off the power immediately and unplug the power

cord from the AC outlet. Then have the instrument inspected by qualified Yamaha

service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• Always replace all batteries at the same time. Do not use new batteries together

with old ones.

• Do not mix battery types, such as alkaline batteries with manganese batteries, or

batteries from different makers, or different types of batteries from the same

maker, since this can cause overheating, fire, or battery fluid leakage.

• Do not tamper with or disassemble batteries.

• Do not dispose of batteries in fire.

• Do not attempt to recharge batteries that are not intended to be charged.

• Keep batteries away from children.

• If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid

should come in contact with your eyes, mouth, or skin, wash immediately with

water and consult a doctor. Battery fluid is corrosive and may possibly cause loss

of sight or chemical burns.

• Always make sure all batteries are inserted in conformity with the +/- polarity

markings. Failure to do so might result in overheating, fire, or battery fluid

leakage.

• When the batteries run out, or if the instrument is not to be used for a long time,

remove the batteries from the instrument to prevent possible leakage of the battery

fluid.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. (If you are using batteries,

remove all batteries from the instrument.) Then have the device inspected by

Yamaha service personnel.

• The power cord or plug becomes frayed or damaged.

• It emits unusual smells or smoke.

• Some object has been dropped into the instrument.

• There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power cord

from the wall AC outlet.

• Use only the stand specified for the instrument. When attaching the stand or rack,

use the provided screws only. Failure to do so could cause damage to the internal

components or result in the instrument falling over.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the desired

listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel or

keyboard. This could cause physical injury to you or others, damage to the

instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing loss.

If you experience any hearing loss or ringing in the ears, consult a physician.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

Battery

If you notice any abnormality

Power supply/AC power adaptor

Location

Connections

Handling caution

DMI-3 1/2

NP-31/NP-11 Owner’s Manual

Always turn the power off when the instrument is not in use.

Even when the power switch is in standby status, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make

sure you unplug the power cord from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

NOTICE

To avoid the possibility of malfunction/damage to the product, or damage to other property, follow the notices below.

 Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° –

40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• Since speakers are built into the instrument you should be careful to never leave any video tapes, cassette tapes, floppy disks or any kind of magnetic

storage media on the panel—doing so may result in data loss or damage to the items.

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal

use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license to use

others' copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and

sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.

 About this manual

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your instrument.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

The serial number of this product may be found on the bottom of the

unit. You should note this serial number in the space provided below

and retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(bottom)

DMI-3 2/2

NP-31/NP-11 Owner’s Manual

Introduction

Setting Up

Be sure to do the following operations BEFORE turning on the power.

Although the instrument will run either from an optional AC adaptor or batteries, Yamaha recommends use of an

AC adaptor whenever possible. An AC adaptor is more environmentally friendly than batteries and does not

deplete resources.

Using an AC Power Adaptor

1 Make sure that the [ ] (Standby/On) switch of

the instrument is off (the power indicator located to

the left of the switch is off).

2 Connect the AC adaptor to the power supply jack.

3 Plug the AC adaptor into an AC outlet.

Using Batteries

1 Open the battery compartment cover located on the

instrument’s bottom panel.

2 Insert six new alkaline batteries, being careful to

follow the polarity markings on the side of the

compartment.

3 Replace the compartment cover, making sure that it

locks firmly in place.

For battery operation, the instrument requires six 1.5V

“AA” size, LR6 or equivalent batteries. (Alkaline bat-

teries are recommended.) When battery power

becomes too low for proper operation, the volume

may be reduced, the sound may be distorted, and other

problems may occur. When this happens, make sure to

replace all batteries, following the precautions listed

below.

Power Requirements

• Use the specified adaptor (page 22). The use of other

adaptors may result in irreparable damage to both the

adaptor and the instrument.

• Unplug the AC Power Adaptor when not using the

instrument, or during electrical storms.

• Never connect or disconnect the AC power adaptor when the power is on

and the batteries are installed. Doing so will turn the power off.

WARNING

CAUTION

AC power

adaptor

AC outlet

NOTE

• Make sure to install the batteries with the proper orienta-

tion, maintaining the correct polarity (as shown). Incorrect

battery installation may result in heat, fire and/or leaking of

corrosive chemicals.

• When the batteries run down, replace them with a com-

plete set of six new batteries. NEVER mix old and new bat-

teries. Do not use different kinds of batteries (e.g. alkaline

and manganese) at the same time.

• If the instrument is not to be used for a long time, remove

the batteries in order to prevent possible fluid leakage and

damage to the instrument.

WARNING

Setting Up

NP-31/NP-11 Owner’s Manual

Make sure to properly connect all external devices you are using (as shown below)

BEFORE turning the power on.

A pair of stereo headphones with a 1/4" stereo phone

plug can be plugged in the PHONES/OUTPUT jack

for convenient monitoring. The speakers are automati-

cally shut off when a plug is inserted into this jack.

The PHONES/OUTPUT jack also functions as an

external output. You can connect the PHONES/OUT-

PUT jack to a keyboard amplifier, stereo system,

mixer, tape recorder, or other line-level audio device

to send the instrument’s output signal to that device.

The SUSTAIN jack is for connecting the Footswitch or

foot pedal. The pedal functions in the same way as a

damper pedal on an acoustic piano. Connect an optional

footswitch FC4/FC5 to this jack and press the pedal to

sustain the sound. An optional FC3 Foot Pedal can also

be connected to this jack. If you connect an optional

FC3 Foot Pedal, the half pedal function* can be used.

* Half pedal function

If you are playing the piano with sustain but want to make the sound

between notes clearer, slightly release your foot from the pedal,

keeping the pedal down in half position or less.

Turn down the volume by turning the [MASTER

VOLUME] dial to the MIN position and press the

[ ] (Standby/On) switch to turn on the power. Press

the [ ] (Standby/On) switch again for a second to

turn the power to standby.

While playing the keyboard, adjust the volume level

by using the [MASTER VOLUME] dial.

To prevent unnecessary power consumption, this

instrument features an Auto Power Off function that

automatically turns the power off if the instrument is

not operated for 30 minutes.

The Auto Power Off function can be set to on or off;

see page 18.

The instrument includes a music rest that can be

attached to the instrument by inserting it into the slot

at the top of the control panel.

Connecting Headphones or an Audio

Device (PHONES/OUTPUT Jack)

• Avoid listening with the headphones at high volume for

long periods of time; doing so may not only result in ear

fatigue, it may be damaging to your hearing.

• To prevent damage to the speakers, set the volume of the

external devices at the minimum setting before connecting

them. Failure to observe these cautions may result in elec-

tric shock or equipment damage. Also, be sure to set the

volumes of all devices at their minimum levels and gradu-

ally raise the volume controls while playing the instrument

to set the desired listening level.

Connecting a Footswitch or a Foot

Pedal (SUSTAIN Jack)

CAUTION

• Make sure that the power is OFF when connecting or disconnecting the

Footswitch or the Foot Pedal.

• Do not turn the power on while pressing the Footswitch or the Foot Pedal.

Otherwise, the switch or pedal type (on/off) will be reversed.

Turning the Power On

• Even when the switch is set to standby, electricity is still

flowing to the instrument at the minimum level. When you

are not using the instrument for a long time, make sure you

unplug the AC power adaptor from the wall AC outlet, and/

or remove the batteries from the instrument.

• All panel settings are reset to the default values whenever the power is

turned off.

Auto Power Off Function

Using the Music Rest

NOTE

CAUTION

NOTE

NP-31/NP-11 Owner’s Manual

Panel Controls and Terminals

q [MASTER VOLUME] dial ........................ page 8

For adjusting the volume level of the entire sound.

w [ ] (Standby/On) switch ....................... page 8

For turning the power on or off.

e [DEMO] button...............................pages 12, 13

For playing all the Voice Demo Songs and Piano

Demo Songs.

r [METRONOME ON/OFF] button ...........page 14

For using the metronome.

t VOICE buttons ...............................pages 10, 11

For selecting the Voices (instrument sounds), such

as Grand Piano.

y TEMPO [t] [s]/BEAT [<] [> ] buttons

................................................................page 14

The tempo and beat of the metronome can be

changed by using these buttons while holding the

[METRONOME ON/OFF] button. The TEMPO

buttons also affect the tempo of the Demo Song.

u [VARIATION] button ..............................page 10

For selecting a different Voice for the Voice button.

i [SUSTAIN] jack ........................................page 8

For connecting a pedal, optional FC3 Foot Pedal or

FC4/FC5 Footswitch.

o MIDI [IN] [OUT] terminals .....................page 19

For connecting external MIDI devices, allowing

the use of various MIDI functions.

!0 [PHONES/OUTPUT] jack ........................page 8

For connecting a set of standard stereo head-

phones, allowing private practice.

This jack also functions as an external output.

!1 DC IN jack ................................................page 7

For connecting the power adaptor.

!0 !1 io

wer t u

C2C1 C3 C4 C5 C6

NP-11

Shows the jacks and terminals as

seen when viewed from the rear

of the instrument.

(The illustration shows

the NP-31)

Shows the jacks and terminals as

seen when viewed from the rear

of the instrument.

NP-31/NP-11 Owner’s Manual

Reference

Selecting & Playing Voices

To familiarize yourself with the character-

istics of the Voices, listen to the Voice

Demo Songs for each Voice (page 12).

Voice:

The term “Voice” refers to a musical

instrument sound built into the Digital

Musical Instrument.

When you select a Voice, an appropriate

reverb type will be selected automatically

(page 16).

Press one of the Voice buttons.

Two different Voices are assigned to each Voice button. You can switch

between them by pressing the [VARIATION] button. After the [Grand Piano]

is pressed, for example, turning on [VARIATION] will call up the Grand Piano

2 Voice while turning off [VARIATION] will call up the Grand Piano 1 Voice.

Adjust the volume.

Rotate the [MASTER VOLUME] dial to set the most comfortable listening

level during your performance.

Selecting Voices

TERMINOLOGY

NOTE

Voice Button Voice Name Description

GRAND

PIANO

Grand Piano 1

Recorded samples from a full concert grand piano.

Perfect for classical compositions as well as any

other style that requires acoustic piano.

VARIATION Grand Piano 2

Clear piano with bright reverb. Good for popular

music.

E.PIANO E. Piano 1

An electronic piano sound created by FM synthesis.

Good for popular music.

VARIATION E. Piano 2

The sound of an electric piano using hammer-struck

metallic “tines.” Soft tone when played lightly, and an

aggressive tone when played hard.

PIPE ORGAN Pipe Organ 1

This is a typical pipe organ sound (8' + 4' + 2'). Good

for sacred music from the Baroque period.

VARIATION Pipe Organ 2

This is the organ’s full coupler sound, often associ-

ated with Bach’s “Toccata and Fugue.”

STRINGS/

VIBES

Strings

Spacious and large-scale string ensemble. Try com-

bining this Voice with piano in DUAL.

VARIATION Vibraphone

The sound of a vibraphone played with relatively soft

mallets.

HARPSI-

CHORD

Harpsichord 1

The definitive instrument for baroque music. Since

the strings of a harpsichord are plucked, there is no

touch response.

VARIATION Harpsichord 2

Mixes the same Voice an octave higher for a more

brilliant, dynamic tone.

Selecting & Playing Voices

NP-31/NP-11 Owner’s Manual

You can play Voices simultaneously across the entire range of the keyboard. In this way, you can combine similar

Voices to create a thicker sound.

Dual mode cannot be used with two

Voices of the single Voice button (for

example, strings and vibraphone).

Reverb in Dual

The reverb type assigned to Voice 1 will

take priority. If the reverb assigned to

Voice 1 is set to OFF, the reverb assigned

to Voice 2 will be in effect.

Refer to “Selecting Voices” on page 10 for

more information on the Voices that are

assigned to the [VARIATION] button.

Press two Voice buttons simultaneously to engage Dual.

The Voice assigned to the left side button will be designated as Voice 1, and the

Voice assigned to the right side button will be designated as Voice 2.

Usin g Variation Voices in Du a l mode

To select a Variation Voice in Dual mode, first select the desired Voice, then

press the [VARIATION] button. Finally, press the two desired Voice buttons

simultaneously. If either of the Voices is a Variation Voice, the [VARIATION]

indicator lights. To use (or cancel) Variation for both Voices, simply press the

[VARIATION] button so that the indicator lights (or goes off).

To exit from Dual, press one of the Voice buttons.

Setting the Octave

While holding down the [VARIATION] button, press one of the C4 – D4 keys

to shift the pitch up or down in octave steps for Voice 1.

While holding down the [VARIATION] button, press one of the D#4 – F4 keys

to shift the pitch up or down in octave steps for Voice 2.

Setting the Volume Balance

While hold down the [VARIATION] button, press one of the F#4 – F#5 keys

(see the illustration) to adjust the volume balance between two Voices. A set-

ting of “0” produces equal balance between Voices 1 and 2. Values below “0”

(to “-6”) decrease the volume of Voice 1 and increase the volume of Voice 2;

values above “0” (to “6”) increase the volume of Voice 1 and decrease the vol-

ume of Voice 2.

Combining Voices (Dual)

NOTE

F4 C5 C6C4

NP-11

NP-31

Voice 1 Voice 2

Voice 1

C4 -1

Voice 2

D#4-1

C#40 E4 0

D4 +1 F4 +1

C5 (0) C6C4

F#5 (+6)F#4 (-6)

NP-11

NP-31

NP-31/NP-11 Owner’s Manual

Listening to the Voice Demo Songs

The instrument features special Voice Demo Songs that effectively showcase each of the Voices.

Refer to the Voice list on page 10 for more

information on the characteristics of each

preset Voice.

The Voice Demo Songs are not transmit-

ted via MIDI.

Simply pressing the [DEMO] button starts

the Demo Song sequence from the Grand

Piano 1 Voice.

The [VARIATION] indicator is lit while the

Demo Song of the Variation Voice is play-

ing back.

You can adjust the tempo of the Voice

Demo Song during playback.

For instructions on setting the tempo, see

page 14.

While holding down the [DEMO] button, press one of the Voice

buttons to start the Voice Demo Song.

The Songs provided for each Voice will play back in sequence.

Changing a Voice Demo Song

During playback, you can change the Voice Demo Song by pressing a different

Voice button.

In addition, you can select a different Voice Demo Song for the Variation

Voice by pressing the [VARIATION] button.

The Voice Demo Song List

The demonstration pieces listed above are short rearranged excerpts of the original composi-

tions.

Press the [DEMO] button to stop

playback.

NOTE

Voice Name Title Composer

Harpsichord 1 Gavotte J.S. Bach

Harpsichord 2 Invention No. 1 J.S. Bach

NP-31/NP-11 Owner’s Manual

Listening to the Piano Demo Songs

The instrument provides Piano Demo Songs as well as Voice Demo Songs, for your listening pleasure.

You can play the keyboard along with the

Piano Demo Song. You can also change

the Voice for playing on the keyboard.

When you select a different Song (or a dif-

ferent Song is selected during chained

playback), an appropriate reverb type will

be selected accordingly.

You can adjust the tempo of the Piano

Demo Song during playback.

For instructions on setting the tempo, see

page 14.

While holding down the [DEMO] button, press one of the 1 – 10

(C#1 – A#1) keys to start the desired Song.

The Piano Demo Songs are assigned to the 1 – 10 (C#1 – A#1) keys.

The selected Piano Preset Song will play back followed by the rest of the

Songs in sequence.

The Piano Demo Songs are not transmit-

ted via MIDI.

Piano Demo Song List

NP-31

NP-11

Press the [DEMO] button to stop

playback.

NOTE

C1 C2

C#1 A#1

C#1

A#1

NP-31

NP-11

NOTE

No. Title Composer

1 Menuett G dur BWV.Anh.114 J.S. Bach

2 Turkish March (Piano Sonate No.11 K.331) W.A. Mozart

3 Für Elise L.v. Beethoven

4 Valse op.64-1 “Petit chien” F.F. Chopin

5 Träumerei R. Schumann

6 Dolly’s Dreaming and Awakening T. Oesten

7 Arabesque J.F.F. Burgmüller

8 Humoresque A. Dvo

řák

9 The Entertainer S. Joplin

10 La Fille aux Cheveux de Lin C.A. Debussy

No. Title Composer

1 Invention No. 1 J.S. Bach

2 Prelude (Wohltemperierte Klavier I No.1) J.S. Bach

3 Le Coucou L-C. Daquin

4 Turkish March W.A. Mozart

5 Little Serenade J. Haydn

6 Ecossaise L.v. Beethoven

7 Moments Musicaux op.94-3 F.P. Schubert

8 Valse op.69-1 “L’adieu” F.F. Chopin

9 Fröhlicher Landmann R. Schumann

10 La chevaleresque J.F. Burgmüller

NP-31/NP-11 Owner’s Manual

Using the Metronome

This instrument features a built-in metronome (a device that keeps an accurate tempo) that is convenient for prac-

ticing.

Press the [METRONOME ON/OFF]

button to start the Metronome.

Press the [METRONOME ON/OFF]

button to stop the Metronome.

Setting the Beat

Default setting:

The “Default setting” refers to the factory

setting obtained when you first turn on the

power to the instrument.

While holding down the [METRONOME ON/OFF] button, use the BEAT [<]

button or the BEAT [>] button to select the Beat from 0, 2, 3, 4, 5 and 6.

The first Beat is accented with a bell sound and the rest with clicks. The

default setting is 0. In this setting, clicks sound for all beats.

The beat can also be changed by the following operation.

While holding down the [METRONOME ON/OFF] button, press one of the

keys C3 – F3.

Adjusting the Tempo

Setting range: q = 32 – 280

Default setting: 120

While holding down the [METRONOME ON/OFF] button, use the TEMPO

[t] or [s] button to decrease or increase in single steps.

While holding down the [METRONOME ON/OFF] button, press both

TEMPO [t]/[s] buttons simultaneously to restore the default tempo.

TERMINOLOGY

Key Beat

C3 0

C#32

D3 3

D#34

E3 5

F3 6

C3 F3C1 C2

NP-31

NP-11

NOTE

Using the Metronome

NP-31/NP-11 Owner’s Manual

Also, while holding down the [METRONOME ON/OFF] button, use the fol-

lowing keys to increase or decrease in single or ten steps.

Increasing the tempo value in steps of one:

While holding down the [METRONOME ON/OFF] button, press the F#2 key.

Decreasing the tempo value in steps of one:

While holding down the [METRONOME ON/OFF] button, press the E2 key.

Increasing the tempo value in steps of ten:

While holding down the [METRONOME ON/OFF] button, press the G2 key.

Decreasing the tempo value in steps of ten:

While holding down the [METRONOME ON/OFF] button, press the D#2 key.

Resetting the tempo to default:

While holding down the [METRONOME ON/OFF] button, press the F2 key.

Entering a specific tempo number

The numbers 0 – 9 are assigned to the keys C1 – A1, respectively (see below).

While holding down the [METRONOME ON/OFF] button, press the appropri-

ate 0 (C1) – 9 (A1) keys in sequence to specify a two or three-digit number.

Select a number starting from the left-most digit. For example, to set the tempo

to “95,” press the 9 (A1) and 5 (F1) keys in sequence.

Adjusting the volume

Setting range:

C4 (1) – G5 (20)

Default setting:

A4 (10)

You can change the volume of the metronome sound.

While holding down the [METRONOME ON/OFF] button, press one of the C4

– G5 keys to determine the volume.

Pressing a higher key results in a higher volume, while pressing a lower key

results in a lower volume.

C3C2

G2 (+10)C1

E2 (-1)

D#2 (-10)

F#2 (+1)

NP-31

NP-11

F2 (default)

C1 C2A1

NP-31

NP-11

NOTE

C6C4

(1)

C5 G5

(20)

NP-11

NP-31

NP-31/NP-11 Owner’s Manual

Other Settings

This control enables you to select four different types of reverb effect that add extra depth and expression to the

sound to create a realistic acoustic ambience.

Selecting a Reverb Type

The appropriate Reverb Type and Depth

are automatically set when a Voice is

selected.

While holding down the [VARIATION] button, press one of the C2 – E2 keys

to select a reverb type (as shown above).

Adjusting Reverb Depth

Setting range:

0 (no effect) – 10 (maximum depth)

While holding down the [VARIATION] button, press one of the C1 – A#1 keys

to adjust the reverb depth for the selected Voice.

The depth value increases as you press higher keys.

While holding down the [VARIATION] button, press the B1 key to set the

reverb to the depth most suitable for the selected Voice.

Adding Variations to the Sound – Reverb

Key Reverb Type Description

C2 Room

This setting adds a continuous reverb effect to the sound, similar to

the acoustic reverberation you would hear in a room.

C#2 Hall1

For a “bigger” reverb sound, use the HALL 1 setting. This effect

simulates the natural reverberation of a small-size concert hall.

D2 Hall2

For a truly spacious reverb sound, use the HALL 2 setting. This

effect sim-ulates the natural reverberation of a large concert hall.

D#2 Stage Simulates the reverb of a stage environment.

E2 Off No effect is applied.

NOTE

E2C1 C2

NP-31

NP-11

NOTE

C1 (0) C2B1

A#1 (10)

NP-31

NP-11

Other Settings

NP-31/NP-11 Owner’s Manual

The Transpose function makes it possible to shift the pitch of the entire keyboard up or down in semitone intervals to

facilitate playing in difficult key signatures, and to let you easily match the pitch of the keyboard to the range of a

singer or other instruments. For example, if you set the transposition amount to “+5,” playing a C key actually pro-

duces a pitch of F. In this way, you can play a song as though it were in C major, and the instrument will transpose it

to the key of F.

Setting the amount of transposition

While holding down the [DEMO] button, press and hold the [METRONOME

ON/OFF] button, then press one of the F#2 – F#3 keys to set the desired

amount of transposition.

Setting range:

F#2 (-6 semitones) – C3 (normal pitch) –

F#3 (+6 semitones)

To transpose the pitch down (in semitone steps)

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press any key between F#2 and B2.

To transpose the pitch up (in semitone steps)

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press any key between C#3 and F#3.

To restore the normal pitch

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press the C3 key.

You can fine tune the pitch of the entire instrument. This function is useful when you play the instrument along

with other instruments or CD music.

Setting the Pitch

Hz (Hertz):

This unit of measurement refers to the fre-

quency of a sound and represents the

number of times a sound wave vibrates in

a second.

Setting range: 427.0 – 453.0 Hz

Default setting: A3 = 440Hz.

To lower or raise the pitch (in steps of roughly 1.0 Hz):

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press G3 (to lower) or B3 (to raise).

To lower or raise the pitch (in steps of roughly 0.2 Hz):

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press G#3 (to lower) or A#3 (to raise).

To restore standard pitch:

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press C3.

Transposing the Pitch

C1 C2

F#3F#2 C3

-1

-2 +1 +3-4

-3-5 +2 +4 +5

-6 +6

NP-31

NP-11

NOTE

Fine Tuning of the Pitch

TERMINOLOGY

NOTE

G#3 (-0.2Hz) A#3 (+0.2Hz)

C1 C2 C3

B3 (+1.0Hz)G3 (-1.0Hz)

NP-31

NP-11

A3 (standard pitch)

Other Settings

NP-31/NP-11 Owner’s Manual

You can adjust the volume level that changes depending on how fast or strong you hit the keys.

The following four settings are available.

Setting the Touch Sensitivity Type

The touch sensitivity settings may have

little or no effect with Pipe Organ 1, 2 and

Harpsichord 1, 2 Voices that are not nor-

mally responsive to keyboard dynamics.

Default setting: Medium

While holding down the [VARIATION] button, press one of the A5 – C6 keys

to select the desired touch sensitivity.

To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automati-

cally turns the power off if the instrument is not used—i.e., no buttons or keys are pressed—for approximately 30

minutes.

If you do not want to use the Auto Power Off function, change the setting as follows.

Default setting: Enable

Turn the power of the instrument off. Then, while holding down the lowest key,

press the [ ] (Standby/On) switch to turn on the power again so that the

[VARIATION] indicator flashes 3 times, after which the Auto Power Off func-

tion is disabled.

If you want to disable the Auto Power Off function without turning the power

off, hold down the [DEMO] button, then press and hold the [METRONOME

ON/OFF] button, then press the A5 key.

Re-enabling the Auto Power Off Function

While holding down the [DEMO] button, press and hold the [METRONOME ON/

OFF] button, then press the G#5 key to enable the Auto Power Off function again.

Touch Sensitivity

Key Touch Sensitivity Description

A5 FIXED

The volume level does not change at all regardless of whether you play the keyboard

soft or hard.

A#5 SOFT The volume level does not change much when you play the keyboard soft or hard.

B5 MEDIUM This is the standard piano touch response (default setting).

C6 HARD

The volume level changes very widely from pianissimo to fortissimo to facilitate dynamic

and dramatic expression. You have to hit the keys hard to produce a loud sound.

NOTE

C6A5

NP-11

NP-31

Disabling the Auto Power Off Function

NOTE

NP-31

NP-11

NP-31

G#5 (enable)

A5 (disable)

NP-31/NP-11 Owner’s Manual

Connecting MIDI Instruments

The instrument features MIDI IN/OUT terminals, allowing you to connect the instrument to other instruments and

devices—including computers—and take advantage of the various performance and recording capabilities in

MIDI applications.

Since MIDI data that can be transmitted or

received varies depending on the type of

MIDI device, check the chapter “MIDI data

format” on page 4 in “MIDI Reference” to

find out what MIDI data and commands

your devices can transmit or receive.

MIDI [IN] [OUT] terminals

Use MIDI cables to connect external MIDI devices to

these connectors.

About MIDI

MIDI (Musical Instrument Digital Interface) is a standard format for data transmis-

sion/ reception. It enables the transmission of performance data and commands

between MIDI devices and personal computers. Using MIDI, you can control a con-

nected MIDI device from the instrument, or control the instrument from a con-

nected MIDI device or computer.

MIDI functions enable you to transmit performance data between MIDI devices.

You cannot transmit the Voice Demo

Songs and the Piano Preset Songs from

the instrument to another MIDI device.

For MIDI connections, use a standard

(optional) MIDI cable, available at most

musical instrument stores.

When the instrument is used as a tone

module, performance data with Voices

that are not found on the instrument will

not be played correctly.

Transmitting performance data to and from another MIDI device

Transmitting performance data to and from a computer

You must install an appropriate software

application on the computer to be able to

transmit performance data between the

instrument and a computer.

Connecting the USB port on the computer to the instrument via an

optional USB-MIDI interface (such as the Yamaha UX16)

Use a USB-MIDI interface device to connect the USB port on your computer

to the instrument’s MIDI terminals. You must install the USB-MIDI interface

(such as the UX16) driver. For more information, refer to the user’s manual

that came with the USB-MIDI interface device.

Connecting to the MIDI [IN] [OUT] terminals

NOTE

MIDI Capabilities

NOTE

• Before connecting the instrument to other electronic components, turn off the power of all

the components.

NOTICE

NOTE

Instrument

MIDI [OUT] terminal

MIDI device

MIDI cables

(optional)

MIDI [IN] terminal

MIDI [OUT] terminal MIDI [IN] terminal

Computer

USB terminal

USB-MIDI interface

(optional)

Instrument

MIDI [IN] terminal MIDI [OUT]terminal

NOTE

• When connecting the instrument to a computer, first turn off the power to the instru-

ment, and then exit any open applications on the computer before connecting any

cables. After making all connections, turn on the power to the instrument.

NOTICE

NP-31/NP-11 Owner’s Manual

MIDI Functions

While holding down the [DEMO] button, press and hold the [METRONOME ON/OFF] button, then press the

appropriate key indicated in the list below to make detailed adjustments to the MIDI settings.

For details on the specific keys and the corresponding setting values, please refer to the included “Quick Opera-

tion Guide.”

Detailed instructions for making MIDI settings are explained in the MIDI Reference document, which can be

downloaded from the Yamaha Manual Library on the Internet. (For details, please refer to the section “About the

Manuals” on page 4.)

Key Setting item

Setting

value

Default Description

C1 – E2

Setting the MIDI Transmit

Channel

1 – 16, OFF

Channel1

This parameter enables you to specify the channel over which the

instrument transmits MIDI data.

C4 – F5

Setting the MIDI Receive

Channel

1 – 16, 1 + 2,

ALL

This parameter enables you to specify the channel over which the

instrument receives MIDI data.

A#5

Setting Local Control ON/

OFF

ON/OFF ON

This parameter enables you to set Local Control to ON or OFF.

Local control can be set to OFF so that the instrument does not

play the internal Voices, but the appropriate MIDI information is

still transmitted via the MIDI OUT terminal when notes are played

on the instrument.

Setting Program Change

ON/OFF

ON/OFF ON

This parameter enables you to set Program Change to ON or

OFF.

This function makes it possible to cancel program change number

reception and transmission so that Voices can be selected on the

instrument without affecting the external MIDI device.

Setting Control Change

ON/OFF

ON/OFF ON

This parameter enables you to set Control Change ON or OFF.

This function makes it possible to cancel control change data

reception and transmission so that, for example, the pedal of the

instrument and other controls can be operated without affecting

an external MIDI device.

Sivu latautuu ...

Yamaha NP-11 Omistajan opas

Brändi: Yamaha

Malli: NP-11

Kategoria: Digital pianos

Tyyppi: Omistajan opas

Tämä käsikirja sopii myös

NP-31

Lataa PDF

raportti

muilla kielillä

polski: Yamaha NP-11 Instrukcja obsługi
Türkçe: Yamaha NP-11 El kitabı
English: Yamaha NP-11 Owner's manual
čeština: Yamaha NP-11 Návod k obsluze
svenska: Yamaha NP-11 Bruksanvisning
русский: Yamaha NP-11 Инструкция по применению
italiano: Yamaha NP-11 Manuale del proprietario
Deutsch: Yamaha NP-11 Bedienungsanleitung
português: Yamaha NP-11 Manual do proprietário
dansk: Yamaha NP-11 Brugervejledning
français: Yamaha NP-11 Le manuel du propriétaire
español: Yamaha NP-11 El manual del propietario
Nederlands: Yamaha NP-11 de handleiding
română: Yamaha NP-11 Manualul proprietarului

Liittyvät paperit

Muut asiakirjat

LANDMANN Grillleuchte, LED 3,7V, Schwarz Käyttö ohjeet