LXE MX3A378CHGR6 Ohjekirja

MX3 Multi-Charger User’s Guide

Model MX3A378CHGR6

(For Use with LXE 156213-0001 and 158224-0001 Lithium Ion Battery Packs)

2381A137OPGDWW

E-EQ-MX3CHGROG-E

The MX3X Main Battery Pack may be incompatible with MX3 Battery Chargers that have not

been upgraded to V1.20 or V1.01.

Notice:

LXE Inc. reserves the right to make improvements or changes in the products described in this manual at any time without notice. While

reasonable efforts have been made in the preparation of this document to assure its accuracy, LXE assumes no liability resulting from any errors

or omissions in this document, or from the use of the information contained herein.

Copyright Notice:

This manual is copyrighted. All rights are reserved. This document may not, in whole or in part, be copied, photocopied, reproduced, translated

or reduced to any electronic medium or machine-readable form without prior consent, in writing, from LXE Inc. Further, LXE Incorporated,

reserves the right to revise this publication and to make changes to it from time to time without any obligation to notify any person or

organization of such revision or changes.

125 Technology Parkway, Norcross, GA 30092, U.S.A. (770) 447-4224

LXE is a registered trademark of LXE Inc. All other brand or product names are trademarks or registered trademarks of their respective

rights reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems Incorporated." applies.

FCC Information:

This device complies with FCC Rules, part 15. Operation is subject to the following conditions:

1. This device may not cause harmful interference

and

2. This device must accept any interference that may be received, including interference that may cause undesired operation.

Warning!

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Changes or modifications to this device not expressly approved by LXE Inc., could void the user’s authority to operate this equipment.

EMC Directive Requirements:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take

adequate measures.

Industry Canada:

This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouiller du Canada.

Le present appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques de le Classe A

préscrites dans le Reglement sur le brouillage radioélectrique édits par le ministere des Communications du Canada.

Revision History:

Revision B, July 2002 -- Formatted document for on-line viewing. Changed Document part number from LXE

2381A137OPGDWW to LXE E-EQ-MX3CHGROG-B where B is current document revision designator. Removed Revision

indicator from footer of document. Removed “Contacting LXE.” “Contacting LXE” is available on the LXE Manuals CD and

the LXE website. Added section titled “Getting Help.”

Revision C, February 2003 -- Added “MX3” to title of manual. Updated model number of the multi-charger from

2381A377CHGR6 to MX3A378CHGR6. Added 1800mAh battery –158224-0001 (MX3A378BATT) .

Revision D, March 2005 -- Added “Important MX3 Battery Charger Update.” Replaced the word “operator” with “user”

throughout (not translated). Added MX3A380RFIDBATT to “Rechargeable Lithium Ion Battery Pack”.

Revision E, October 2005 – Added WEEE statement to “Introduction.”

IMPORTANT SAFETY WARNINGS US

SAVE THESE INSTRUCTIONS

This document contains important safety and operating instructions for the LXE Multi-Charger. Please read all

instructions and cautionary markings on the charger itself before putting the unit into service.

Safety Alert Symbols

This symbol is used to call your attention to instructions concerning your personal safety.

Watch for this symbol – it will alert you to important safety precautions that must be

observed to avoid death, personal injury or property damage. Follow the instructions after

the warning symbol and be alert to the possibility of personal injury or death.

These signal words provide users with information about the seriousness of the hazard involved:

DANGER WARNING CAUTION

Indicates imminent hazards

which, if not avoided, WILL

result in severe personal

injury or death.

Indicates potential hazards

which, if not avoided,

COULD result in severe

personal injury or death.

Indicates hazards or unsafe practices

which, if not avoided, COULD result in

minor or moderate personal injury or

property damage.

Safety Instructions

Setting up the Multi-Charger

Locate or orient the AC cord so that it will not be stepped on, tripped over or subjected to damage or stress.

Charge only LXE part no. 156213-0001 and 158224-0001 Rechargeable Lithium Ion Battery Pack in this charger.

Other batteries or battery packs may burst causing injury or property damage.

Operating the Multi-Charger

Only users who have read and understand all operating instructions are qualified to operate the Multi-Charger.

Failure to read, understand and follow safety instructions may result in injury or death.

Keep the rear of the charger free of obstacles and do not block the rear ventilation slots. The charger generates

internal heat during charging.

Keep the charger away from any heat source. Excessive internal heating can ruin the charger.

Use care when inserting battery. Do not "slam" or slide the battery into the pocket, this could damage the charger.

Keep dirt and foreign objects out of the battery pocket. Do not short circuit any of the contacts in the battery pocket,

this could result in injury or property damage.

Do not operate the charger if it has been dropped or damaged in any way. Return the charger to LXE.

Storing the Multi-Charger

Disconnect charger by pulling the plug; not the cord.

Maintaining the Multi-Charger

Service should be performed by trained persons only. Return the charger to LXE.

Caring for Batteries

Do not dispose of batteries into a fire. Burning will generate hazardous vapors and may cause the battery to explode.

Failure to observe this warning may result in injury from inhalation of vapors or burns from flying debris.

Do not immerse batteries in water or any other liquid. If batteries are immersed, contact LXE.

Do not disassemble or perform modifications to the battery. There are no user serviceable components in the

battery.

Do not place battery into pocket or toolbox with conductive objects (coins, keys, tools, etc.).

A battery placed on damp ground or grass could be electrically shorted. Lay the battery on its side when not in use.

Do not store batteries above 140°F (60°C) for extended periods.

Failure to observe these warnings could result in injury or damage to the battery from rapid discharge of energy or

overheating of the battery.

Electrical Shock Hazards

The following precautions should be observed to avoid the risk of electrical shock hazards associated with charging

batteries:

The Multi-Charger has been designed for indoor use only. Do not operate outdoors or in extremely high humidity

environments. Do not expose charger to rain, snow or wet conditions.

Unplug the charger from power source before cleaning. Use only mild detergent with a slightly damp cloth to clean

the outside of the charger. Do not use solvents or flammable cleaners. Allow the case to dry fully before using

again.

Use of attachments or accessories not recommended by LXE could result in fire, electric shock or injury.

This appliance must be properly grounded. If it should malfunction or break down, grounding provides a path of

least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord

having an equipment grounding conductor and ground outlet that is properly installed and grounded in accordance

with all local codes and ordinances. Do not operate the charger with a damaged AC cord or plug. LXE does not

recommend the use of any extension cord with the Multi-Charger.

The Multi-Charger has been designed for use on a nominal 100 or 120 volt or nominal 220 or 240 volt circuit and

has a grounding attachment plug. The plug is an IEC configuration that is appropriate for your country and

regulations. Make sure that the appliance is connected to an outlet having a configuration similar to the plug. No

adapter should be used with this appliance. Improper connection of the equipment-grounding conductor can result

in a risk of electric shock.

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the appliance. If it will not fit in the outlet, have a proper outlet

installed by a qualified electrician.

Do not disassemble the Multi-Charger. It contains no user serviceable parts.

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

Table of Contents

INTRODUCTION 1

Purpose of this Manual ............................................................................................ 1

Quick Start................................................................................................................. 1

Intended Use ............................................................................................................. 1

Important MX3 Battery Charger Update.................................................................. 2

Battery Chargers Affected..................................................................................................................... 2

Battery Label Location.......................................................................................................................... 2

Specifications............................................................................................................ 3

Electrical Specifications........................................................................................................................ 3

Operating Temperature Ranges............................................................................................................. 3

Dimensions............................................................................................................................................ 3

Rechargeable Lithium Ion Battery Pack ............................................................................................... 3

Controls and Connectors......................................................................................... 4

Multi-Charger........................................................................................................................................ 4

LXE 156213-0001 and 158224-0001 Rechargeable Lithium Ion Battery Packs.................................. 5

INSTALLATION AND OPERATION 6

Introduction............................................................................................................... 6

Setup.......................................................................................................................... 6

Placing the Battery Pack into the Charger.............................................................. 7

Orienting the Battery Pack.................................................................................................................... 7

Inserting the Battery Pack ..................................................................................................................... 7

Interpreting the LEDs............................................................................................................................ 8

RED - on any charge pocket............................................................................................................... 8

RED FLASHING - on all charge pockets .......................................................................................... 8

GREEN - on any charge pocket ......................................................................................................... 8

YELLOW - on any charge pocket...................................................................................................... 8

NO LIGHT - on a charge pocket........................................................................................................ 8

NO LIGHT - on all charge pockets .................................................................................................... 8

Normal Operations................................................................................................................................ 9

Maintenance.......................................................................................................................................... 9

Storage .................................................................................................................................................. 9

Service................................................................................................................................................... 9

A

PPENDIX 10

Troubleshooting Guide........................................................................................... 10

Getting Help........................................................................................................................................ 11

I

MPORTANT SAFETY WARNINGS - TRANSLATIONS 12

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Illustrations

Figure 1 MX3 Multi-Charger Components ..........................................................................................................4

Figure 2 Lithium Ion Battery Pack Components ..................................................................................................5

Figure 3 Multi-Charger Charging Pocket .............................................................................................................6

Figure 4 Battery Pack Insertion ............................................................................................................................7

E-EQ-MX3CHROG-E MX3 Multi-Charger User’s Guide

Introduction

Purpose of this Manual

This user’s guide is intended to familiarize the user with the safety and operating instructions

necessary to use the Multi-Charger (LXE Model MX3A378CHGR6) to charge LXE Rechargeable

Lithium Ion Battery Packs.

This manual should be readily available to all users and maintenance personnel using this charger.

Quick Start

This manual provides the following instructions for operating the Multi-Charger.

• Setting Up the Charger

• Inserting the Battery Pack

• Interpreting the LEDs

Intended Use

The LXE Multi-Charger (MX3A378CHGR6) is designed to simultaneously charge six LXE

Rechargeable Lithium Ion Battery Packs in less than four hours, depending upon battery pack

temperature and conditions

.

Note: Store the charger in a cool, dry place.

Important: This symbol is placed on the product to remind users to dispose of Waste Electrical

and Electronic Equipment (WEEE) appropriately, per Directive 2002-96-EC. In most areas, this

product can be recycled, reclaimed and re-used when properly discarded. Do not discard labeled

units with trash. For information about proper disposal, contact LXE through your local sales

representative, or visit www lxe com.

2 Important MX3 Battery Charger Update

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Important MX3 Battery Charger Update

Battery Chargers Affected

MX3 Multi-Charger Plus

9000A377CHGR5

Use LXE V1.01 Upgrade Kit

MX3 Multi-Charger

MX3A378CHGR6

(Not Available After July-2003)

Use LXE V1.20 Upgrade Kit

The MX3X Main Battery Pack may be incompatible with MX3 Battery Chargers that have not

been upgraded to V1.20 or V1.01. To successfully charge the MX3X Battery Pack in the cradles

or a multi-charger, pre-existing MX3 Battery Chargers must be returned to LXE for a software

upgrade.

Using a Multi-Charger Plus Battery Charger with the MX3X Battery Pack

The MX3X device is designed to use a 2.2Ahr Main Battery Pack to achieve 8+ hours of

continuous operation.

If the MX3X battery pack is inserted into a MX3 Multi-Charger Plus (without the V1.01 upgrade)

bay , the battery may not become fully charged in the 4 hour time limit and a red LED illuminates

after 4 hours have elapsed indicating a Battery Problem.

Remove and reinsert the MX3X battery pack into the same charging bay. This will reset the timer

and allow the charger to complete the charge cycle for the battery in approximately 2 hours..

LXE does not supply an external timing device with the Multi-Charger Plus.

Battery Label Location

The MX3X battery pack has a silver label (see the figure below for the location of the label on the

main battery packs).

125 Technology Parkway

Norcross, GA 30092 USA

Risk of fire, explosion, or burns. Do not short circuit, crush, heat above

100 C, incinerate or disassemble the battery.

!

Specifications 3

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

Specifications

Electrical Specifications

Parameter Min Typical. Max. Comment

Power Supply Input

Voltage (V

AC-IN

)

88VAC 110VAC 132VAC Auto-switching

Power Supply Input

Voltage(V

AC-IN

)

176VAC 220VAC 264VAC Auto-switching

Power Supply Input

Frequency (freq)

47Hz 63Hz

Maximum Charge Current

(I

MAX

)

1A 1.25A

Cutoff Voltage (V

OUT

) 12.3V ± 50mV 4.1V per cell

Charge Termination

Current (I

T

)

50mA ± 20mA

Operating Temperature Ranges

Minimum Maximum Comment

Operating 0°C (32°F) +50°C (122°F) Battery packs shall only be charged when their

temperature is between 10°C (50°F) and 35°C (95°F).

Charging +10°C (50°F) +35°C (95°F) Battery packs will not charge if their temperature is outside

this range.

Storage -20°C (-4°F) +70°C (158°F) Unit is off.

Dimensions

Weight 11.6 pounds

Plug Type IEC; 3-prong

Rechargeable Lithium Ion Battery Pack

LXE Part No.

156213-0001 158224-0001

LXE Order No.

2381A376BATT1600 MX3A378BATT MX3A380RFIDBATT

Specified Capacity

1400mAh 1800mAh 1800mAh

4 Controls and Connectors

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Controls and Connectors

Multi-Charger

Figure 1 MX3 Multi-Charger Components

1. Front

2. Battery Charging Pockets

3. LED Indicators

4. Back

5. Power Connection

6. Ventilation Slots

Controls and Connectors 5

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

LXE 156213-0001 and 158224-0001 Rechargeable Lithium Ion Battery Packs

Figure 2 Lithium Ion Battery Pack Components

1. Front Side

2. Contacts, Battery

B+ = Battery (+), B- = Battery (-), T = Thermistor Sense

3. Contacts, Cradle Output

C+ = Cradle Power (+), C- = Cradle Power (-), D = Docked Signal

4. Retaining Clip

5. Top Side

6. Back Side

7. Contacts, Cradle Input

C+ = Cradle Power (+), C- = Cradle Power (-), D = Docked Signal

6 Introduction

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Installation and Operation

Introduction

The life and capacity of a Lithium Ion battery can vary significantly depending on the discharge

current and the environment in which it is used. As with all batteries, expect to see a reduction in

the total number of operations a fully charged battery pack can deliver as it ages. Charging times

may increase but will not exceed four hours. Battery packs do not need to be fully discharged

between charge cycles.

Setup

• Ensure that the location you choose for the battery charger is well ventilated.

• Place the charger on a horizontal, hard surface.

• Plug the power cord into a properly grounded outlet.

• On initial power-up, all 6 LEDs will light yellow for a few seconds.

Figure 3 Multi-Charger Charging Pocket

1. Battery Charging Pocket

2. Retaining Pins

3. Battery Charger Contacts

4. LED Indicator

Placing the Battery Pack into the Charger 7

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

Placing the Battery Pack into the Charger

Orienting the Battery Pack

Caution!

It’s important that battery packs are inserted into the charging pocket correctly.

Inserting the battery incorrectly could result in damage to the battery pack or the

charger.

When preparing the battery pack for insertion into the charger pocket, hold it with the Back (the

side with only three metal contacts and grooved surface) upward, and the Top (the side with the

metal retaining clip) to the left. The Front (the side with the six contacts and the smooth surface)

will face downwards, into the charging pocket.

Inserting the Battery Pack

Lower the battery pack straight into the battery charger pocket and push it down firmly until the

retaining clip catches on the retaining pins.

Figure 4 Battery Pack Insertion

Caution!

Do not "slam" or slide the battery pack into the charger. Damage may result.

8 Placing the Battery Pack into the Charger

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Interpreting the LEDs

The status of the charge operation is communicated by the LED located at the base of each

charging pocket.

RED - on any charge pocket

Continuous Battery pack - charging.

Flashing Battery pack fault or failure.

Battery charger timeout period expiration.

RED FLASHING - on all charge pockets

Battery charger fault or failure.

GREEN - on any charge pocket

Continuous Battery pack charge complete - Ready.

YELLOW - on any charge pocket

Continuous Battery pack temperature is out of range - Standby.

NO LIGHT - on a charge pocket

No battery pack installed.

Defective or damaged battery pack or charger. Refer to Troubleshooting Guide.

NO LIGHT - on all charge pockets

No battery packs installed.

No power applied to the Multi-Charger.

Placing the Battery Pack into the Charger 9

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

Normal Operations

The optimal operating temperature range for the Multi-Charger is between 50°F and 95°F (10°C

and 35°C). While charging, the charger and battery pack will generate enough heat to feel warm.

This is normal and does not indicate a problem. Do not store the battery pack in direct sunlight or

anywhere the battery pack cannot cool down. If the battery pack is hot after removal from the

computer, allow it to cool at room temperature before placing it in the charger.

Charge times may increase significantly if the battery is warm or hot, since it takes the battery

pack longer to cool down while in the charger pocket. If the battery pack is hot from severe

environmental use and immediate recharging is necessary, place the battery pack in a cool air

stream or in a cool location until it is no longer warm to the touch before charging.

Maintenance

Use a clean soft cloth to wipe any dirt, moisture or grease from the battery pack, contacts or the

charger. Do not use any liquid to clean the battery pack or charger contacts.

Storage

Battery packs should be kept in a cool, dry place whenever possible. Do not store battery packs in

direct sunlight, on a metal surface, or anywhere the battery pack cannot cool down. Do not leave

the battery pack in a non-operating charger. The battery pack may discharge through the charger

rather than hold its charge.

Service

There are no user serviceable parts in the LXE 156213-0001 and 158224-0001 Rechargeable

Lithium Ion Battery Packs or the Multi-Charger. Should your charger require service, contact

LXE. Refer to section titled “Getting Help.”

10 Troubleshooting Guide

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Appendix

Troubleshooting Guide

The following is intended as an aid in determining whether the battery pack or the charger may be

malfunctioning.

Problem Cause Solution

Battery pack does not fit in

charger pocket.

Different manufacturer's

battery pack, or there is an

object in the charger pocket.

Check if the battery pack is LXE part number

156213-0001 or 158224-0001. If not, do not

use. Remove the object from the charger

pocket.

No battery pack in charger,

but charging, battery fault,

and temperature LEDs are

on.

Dirt or foreign objects are in

the charger pocket.

Unplug charger from outlet. Remove any dirt

or foreign objects from charger pocket. If the

LEDs continue to remain ON, the charger may

be defective. Return charger to an authorized

LXE service center.

Charger is plugged into a live

outlet, battery pack is

inserted, but RED LED is

OFF and no other LEDs are

on.

Battery pack is not making

contact with terminals in the

charger pocket.

Push battery pack in firmly. Do not "slam" the

battery pack into the battery pocket.

RED LED at any station is

flashing

The battery pack is not

making good contact with

terminals in charger pocket.

OR

Push battery pack in firmly. Do not “slam” the

battery pack into the charger pocket.

Current could not be sourced

through the battery pack due

to age, exhaustion or damage

to the cell(s).

OR

Contact LXE for battery pack replacement

options.

The battery pack voltage has

not reached 10.6VDC within

90 minutes and the charger

has timed out.

OR

Contact LXE for battery pack replacement

options.

The charger’s 4-hour or 6-

hour timeout period has

expired.

Make sure that the battery pack temperature is

within specification and retry charging. If

problem repeats, contact LXE for battery pack

replacement options.

Troubleshooting Guide 11

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

Problem Cause Solution

YELLOW LED comes ON

when battery pack is first

inserted in the charger.

The battery pack is too hot or

too cold to charge.

Remove battery pack from the charger and

allow it to adjust to room temperature.

NOTE: If the battery pack is left in the

charger, it will cool down or warm to

a temperature upon which the charger

will begin the charge cycle. However,

depending on the temperature of the

battery, it may take 2-3 hours to

adjust. The cool-down of a battery

pack is much quicker if the battery is

not in the charger pocket.

YELLOW LED comes on

when battery pack is in the

CHARGING cycle. The

charge cycle has been

suspended.

The battery pack has become

too hot or too cold to

continue charging.

If this is the first time the battery pack has

initiated a temperature fault, remove the battery

pack and allow it to achieve room temperature.

Then try to charge the battery pack a second

time. If the YELLOW LED comes on again,

the battery pack is defective, or the temperature

of the charger or battery pack is out of

specification.

When you first put a fully

charged battery pack in the

charger, the RED LED

comes on, indicating the

battery pack needs charging.

There is nothing wrong with

the battery pack or charger.

During the first few minutes,

the charger checks the battery

pack for correct voltage and

charge state. During this time

the RED LED is continuously

ON. After charging is

complete, the GREEN LED

comes ON.

Do not "top off" a fully charged battery pack

by repeatedly placing it in charger. The battery

pack may overheat and be damaged!

Getting Help

All LXE manuals are now available on one CD and they can also be viewed/downloaded from the

LXE ServicePass web page. Contact your LXE representative to obtain the LXE Manuals CD.

You can also get help from LXE by calling the telephone numbers listed on the LXE Manuals

CD, in the file titled "Contacting LXE". This information is also available on the LXE website.

12 Troubleshooting Guide

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Important Safety Warnings - Translations

CN Chinese

DA Danish

DE German

ES Spanish

FI Finnish

FR French

GK Greek

IT Italian

JP Japanese

KR Korean

NL Dutch

NO Norwegian

PT Portuguese

SE Swedish

TR Turkish

Important Safety Warnings - CN T-1

E-EQ-MX3CHGROG-E MX3 Multi-Charger User’s Guide

CN

T-2 Important Safety Warnings - CN

MX3 Multi-Charger User’s Guide E-EQ-MX3CHGROG-E

Sivu latautuu ...

LXE MX3A378CHGR6 Ohjekirja

Tämä käsikirja sopii myös

LXE MX3A378CHGR6 Ohjekirja

muilla kielillä

Liittyvät paperit

Muut asiakirjat