Yamaha RX-A2000 Omistajan opas

Owner’s Manual

AV Receiver English for Canada

En 2

BEFORE USE

About this manual

Supplied accessories

Check that you received all of the following parts.

• Remote control

• Simplified remote control

• Batteries (AAA, R03, UM-4) x 4

• Power cable

• YPAO microphone

• AM loop antenna

• Indoor FM antenna

Language selection

This procedure allows you to select the language of

menus and messages on the TV screen.

1

Press hON SCREEN to display the ON

SCREEN menu.

2

Press iCursor B / C to select “Setup” and

press iENTER.

3

Press iCursor D / E to select the

“Language” and press iENTER.

4

Press iCursor B / C to select the favorite

language from the following options.

5

Press hON SCREEN to close the ON

SCREEN menu.

ON SCREEN

ENTER

SOU

R

C

E

R

ECEIVE

R

AV

AU

DI

O

4

3

1

2

7

5

6

V

-A

UX

4

3

1

2

US

B

MU

LTI

N

ET

P

H

O

N

O

TUNER

D

OC

K

[

B

]

[

A

]

h

i

• Some features are not available in certain regions.

• This manual is created prior to production. Design and

specifications are subject to change in part as a result

of improvements, etc. In case of differences between

the manual and product, the product has priority.

• “

hON SCREEN” (example) indicates the name of

the parts on the remote control. Refer to the “Remote

control” (☞

p. 12) for the information about each

position of the parts.

• J

1 indicates that the reference is in the footnote.

Refer to the corresponding numbers on the bottom of

the page.

• ☞

indicates the page describing the related

information.

• Click on the “ ” at the bottom of the page to

display the corresponding page in “Part names and

functions.”

Front panel

Rear panel

Front panel display

Remote control

English (English), (Japanese),

(French), (German), (Spanish),

(Russian)

En 3

CONTENTS

INTRODUCTION

Features and capabilities ...................................................5

Using the TV OSD to operate the unit .............................6

Basic OSD menu operations.............................................6

Viewing or modifying content for the current input source

<Content window> ...........................................................6

Configuring settings for this unit

<ON SCREEN menu>......................................................6

Adjust settings for each input source <Option menu> .....7

Part names and functions..................................................8

Front panel........................................................................8

Front panel with the cover opened ...................................9

Rear panel.......................................................................10

Front panel display .........................................................11

Remote control ...............................................................12

Remote control with the cover open...............................13

On-screen display ........................................................... 14

CONNECTIONS

Connecting speakers ........................................................15

Speaker channels and functions...................................... 15

Speaker layout ................................................................16

Connecting speakers and subwoofers.............................20

Advanced speaker configuration .................................... 24

Speaker layout utilizing an external power amplifier..... 24

Connecting an external amplifier ................................... 26

Connecting external components....................................27

Jacks and cables.............................................................. 27

Connecting a TV monitor............................................... 28

Connecting BD/DVD players and other devices............31

Connecting game consoles or video camcorders............36

Connecting a multi-format player

or an external decoder .................................................... 36

Connecting a SCENE link

playback-compatible device ...........................................37

Using the Trigger function to link

external component power.............................................. 37

Connecting audio/video recording devices .................... 38

Connecting to the network ............................................. 38

Connecting a USB storage device.................................. 39

Connecting the FM/AM antennas .................................. 40

Setting up the speaker parameters automatically

(YPAO).............................................................................. 41

PLAYBACK

Basic playback procedure ............................................... 48

Changing input settings with a single key

(SCENE function) ............................................................ 50

Selecting a SCENE suited to an external component .... 50

Enjoying favorite sound field effect ............................... 51

Selecting sound programs and sound decoders.............. 51

Enjoying surround sound

with the CINEMA DSP function ................................... 51

Enjoying unprocessed playback

(Straight decoding mode) ............................................... 52

Enjoying Hi-Fi Sound Quality (Pure Direct Mode) ....... 53

Enjoying stereo playback ............................................... 53

Enjoying compressed music source with better sound

quality (Compressed Music Enhancer) .......................... 53

Sound programs.............................................................. 54

Using the TV display to control this unit....................... 56

Basic operations via the TV screen display ................... 56

Configuring settings specific to an individual input

source (Option menu)...................................................... 58

Option menu display and setup ...................................... 58

Option menu................................................................... 59

Confirming and operating input sources

from the content window................................................. 62

Displaying the content window on the TV screen ......... 62

Switching the display between the Now Playing view

and the Browse view ...................................................... 62

FM/AM tuning................................................................. 63

Selecting a frequency for reception (Normal tuning) .... 63

Navigating the FM/AM tuner

from the content window ............................................... 64

Playing back tunes on the PC......................................... 66

Windows Media Player setup......................................... 66

Playback of PC music contents...................................... 66

Playing back tunes on the USB storage devices............ 68

Playback of the USB storage device .............................. 68

Listening to the Internet Radio ...................................... 70

Listening to Internet Radio ............................................ 70

Using shortcut function................................................... 72

Playing back tunes from your iPod™/iPhone™........... 73

Connecting the Universal Dock for iPod ....................... 73

Controlling an iPod™/iPhone™ .................................... 73

Playing iPod™/iPhone™ from the menu screen

(Menu browse control)................................................... 74

Operating basic playback functions

via the remote control (Simple remote control) ............. 75

Playing iPod™/iPhone™ with wireless connection ...... 75

Playing back tunes from Bluetooth™ components ...... 77

Connecting a Yamaha Bluetooth

Wireless Audio Receiver................................................ 77

Pairing Bluetooth™ components ................................... 77

Using Bluetooth™ components ..................................... 78

Controlling this unit by using the Web browser

(Web Control Center)...................................................... 79

Displaying and Operating Web Control Center ............. 79

En 4

SETUP

Configuring input sources (Input menu) .......................81

Configuring input sources ..............................................81

Input menu......................................................................82

Editing the SCENE function (Scene menu)................... 84

Editing a scene................................................................ 84

Scene menu.....................................................................85

Simple registering as the SCENE...................................86

Setting sound program parameters

(Sound Program menu) ...................................................87

Editing sound programs..................................................87

CINEMA DSP parameters ............................................. 88

Parameters usable in certain sound programs ................90

Parameters usable in surround decoder .......................... 91

Setting various functions (Setup menu) .........................92

Operating the Setup menu ..............................................92

Setup menu .....................................................................93

Manages settings for speakers ........................................93

Setting the audio output function of this unit .................97

Setting this unit’s video output function.........................99

Setting HDMI functions ...............................................100

Adjusting this unit’s network parameters.....................103

Setting this unit’s multi-zone function .........................104

Making the receiver easier to use ................................. 105

Language ......................................................................108

Confirming information of this unit

(Information menu) .......................................................109

Selecting information ...................................................109

Controlling the remote control

to operate various functions.......................................... 111

Keys connecting external components ......................... 111

Customizing the remote control ................................... 112

Setting remote control codes........................................ 112

Programming from other remote controls .................... 114

Changing source names in the display window ........... 116

Macro programming features ....................................... 117

Clearing configurations ................................................ 118

Simplified remote control............................................. 120

Extended functionality that can be configured

as needed (Advanced Setup menu)............................... 121

Displaying/Setting the Advanced Setup menu............. 121

Setting the impedance of speakers .............................. 121

Remote sensor .............................................................. 122

Avoiding crossing remote control signals

when using multiple Yamaha receivers ........................ 122

Changing TV format .................................................... 123

Removing HDMI video output up-scaling limits......... 123

Recovery and backup of the system settings................ 123

Initializing various settings for this unit....................... 123

Firmware update........................................................... 124

Firmware version.......................................................... 124

Using the HDMI Control function ............................... 125

Enjoying the contents in another room ....................... 129

Connecting Zone2 or Zone3......................................... 129

Controlling Zone2 or Zone3......................................... 131

Enjoying the music in all rooms................................... 131

APPENDIX

Troubleshooting ............................................................. 132

General......................................................................... 132

HDMI™ ....................................................................... 134

Tuner (FM/AM) ........................................................... 135

USB and Network ........................................................ 136

iPod™/iPhone™ .......................................................... 137

Bluetooth™.................................................................. 138

Remote control............................................................. 138

Glossary.......................................................................... 139

Audio information........................................................ 139

Sound program information ......................................... 140

Video information ........................................................ 141

Compatibility of the input and output video signals .... 141

Information on HDMI™............................................... 142

About trademarks ......................................................... 143

Specifications.................................................................. 144

Index ............................................................................... 146

En 5

INTRODUCTION

■ Built-in high-quality, high-power 7-channel amplifier

■ Multi-channel speaker configuration capability

– 2- to 7.1-channel speaker configurations .................................................................................................16

– Presence speaker connections for playback with a richer sound field effect...........................................15

– Bi-amplification connections for high-quality playback .........................................................................21

– External amplifier connections for high-quality playback and expansion of channels ...........................24

– Speaker impedance configuration............................................................................................................21

■ HDMI compatibility

– 8 HDMI input jacks (7 on the rear, 1 on the front) supporting 3D video signal input ............................31

– 2 selectable HDMI output jacks supporting Audio Return Channel and 3D video signal ......................29

■ Automatic setup for speaker acoustic parameters

(YPAO - Yamaha Parametric Room Acoustic Optimizer) ......................................41

■ Extensive inputs (max. 13) for external playback components

– BD/DVD/CD player connection ..............................................................................................................31

– Game console / video camcorder connection ..........................................................................................36

– Multi-format player / external decoder connection .................................................................................36

– iPod/iPhone wired connection .................................................................................................................73

– iPod/iPhone wireless connection .............................................................................................................75

– Bluetooth component connection ............................................................................................................77

■ 1-button input/sound program/setting switching (SCENE function)...................50

■ Built-in sound programs and surround decoders for playback variety of sources

– Spatial sound playback with sound field effects (CINEMA DSP) ..........................................................51

– Playback with no sound field effects (straight decoding) ........................................................................52

– High-fidelity sound playback (Pure Direct).............................................................................................53

– Enhanced sound playback for compressed sources (Compressed Music Enhancer)...............................53

■ Tuner playback

– FM/AM broadcast....................................................................................................................................63

■ Playback and control via network

– Playback of music on the PC and DLNA server......................................................................................66

– Internet radio service playback ................................................................................................................70

– Control this unit via network (Web Browser Control).............................................................................79

■ Playback of music on the USB storage devices ................................................... 68

■ Sophisticated on-screen display (OSD) for easy operation

– Selection of input sources, scenes, and sound programs .........................................................................56

– Navigation for the current input source (content window)......................................................................62

– Setup for this unit (ON SCREEN menu) .................................................................................................81

– Setup for each input source (Option menu) .............................................................................................58

■ Customizable remote control

– Remote control code setup for operation of external components ........................................................112

– Learning function from other remote controls.......................................................................................114

– Programming macro for a series of operations......................................................................................117

■ Multi-room listening capability (Zone2/Zone3) ................................................... 129

Features and capabilities

Most of functions can be operated with on-screen display on the TV screen. Refer to “Using the TV

OSD to operate the unit” on the following pages for information on functions that can be controlled

using the on-screen display.

INTRODUCTION

En 6

This unit features a sophisticated on-screen display (OSD) for the TV screen. The OSD is designed to enable visual guidance that simplifies operations. The OSD mainly displays the ON SCREEN and

Option menus, as well as the content window that displays the content of current input sources.

Basic OSD menu operations

■ Select an input source, scene and sound program

– Select an input source ..............................................................................................................................56

– Select a scene ...........................................................................................................................................56

– Select a sound program............................................................................................................................57

■ Select a language

– Change the language displayed on the TV screen <Language>............................................................108

Viewing or modifying content for the current input source

■ Operate the FM/AM tuner

– Display preset stations for selection ........................................................................................................64

– Display information on the station currently received.............................................................................64

– Perform operations such as searching for and registering stations using the screen button ....................64

■ Operate the Internet radio

– Display information on the station currently received.............................................................................70

– Play back radio contents ..........................................................................................................................70

– Bookmark Internet radio stations.............................................................................................................70

■ Operate the iPod music sources

– Display the list of iPod music sources for selection ................................................................................74

– Perform operations such as play, stop and pause using the TV screen <Menu browse control> ............74

Configuring settings for this unit <ON SCREEN menu>

■ Configure an input source

– Change the input source name <Rename/Icon Select> ...........................................................................82

– Specify a format for digital audio signals <Decoder Mode> ..................................................................83

– Enhance the sound of compressed audio <Enhancer> ............................................................................83

– Output a video signal input from another input source

while playing a multi-channel audio signal <Video Out> .......................................................................83

– Charge the iPod/iPhone when this unit is in standby mode <Standby Charge>......................................83

– Play music sources on a PC using external controls <DMC Control>....................................................83

■ Customize a scene

– Register or clear settings for a selected scene <Save>, <Load>, <Reset> ........................................85, 86

– Turn on a Yamaha BD/DVD player or CD player connected to this unit automatically

when a scene is selected <SCENE IR> ...................................................................................................85

– Changing a scene name and icon <Rename/Icon Select> .......................................................................86

■ Adjust a sound program (sound program)

– Adjust sound program parameters ...........................................................................................................87

■ Display settings information for this unit

– Display audio signal information <Audio Signal>................................................................................109

– Display video signal information <Video Signal> ................................................................................109

– Display HDMI signal information <HDMI Monitor>...........................................................................109

– Display network information <Network>..............................................................................................110

– Display system information <System>..................................................................................................110

– Display Zone information <Zone> ........................................................................................................110

Using the TV OSD to operate the unit

Continues to the

INTRODUCTION

Using the TV OSD to operate the unit

En 7

■ Adjust acoustic parameters to match your speakers and listening environment

– Specify speaker acoustic parameters automatically

(Yamaha Parametric Room Acoustic Optimizer - YPAO).......................................................................41

– Set up this unit’s speaker configuration simply <Power Amp Assign> ..................................................94

– Specify settings for each speaker <Configuration> .................................................................................94

– Control volume control for each speaker <Level> ..................................................................................96

– Apply speaker distance settings <Distance> ...........................................................................................96

– Control equalizer sound quality <Parametric EQ>..................................................................................96

– Adjust test tone speaker <Test Tone> ......................................................................................................97

■ Adjust audio signals output from this unit

– Correct lag between audio and video signals <Lipsync> ........................................................................97

– Select a dynamic range adjustment method <Dynamic Range> .............................................................98

– Specify the maximum volume <Max Volume> .......................................................................................98

– Specify the initial volume <Initial Volume>............................................................................................98

– Restrict video signal in Pure Direct Mode <Pure Direct Mode>.............................................................98

– Adjust DSP effect and volume level <Adaptive DSP Level> ..................................................................98

■ Adjust video signals output from this unit

– Convert analog video signal to another type of signal <Analog to Analog Conversion> .......................99

– Specify the resolution and aspect ratio of video signals and adjust video quality <Processing>............99

■ HDMI settings

– Assign the audio input source for the TV <TV Audio Input>...............................................................101

– Listen to TV audio with HDMI cable connection <ARC (Audio Return Channel)>............................101

– Transmit HDMI audio/video to the TV during standby mode <Standby Through> .............................102

– Change the output destination of HDMI input audio signals <Audio Output>.....................................102

■ Network settings

– Specify this unit’s IP address <IP Address> ..........................................................................................103

– Accept the commands over a LAN network when this unit is in the standby mode

<Network Standby> ...............................................................................................................................103

– Specify the mac address filter for this unit <MAC Address Filter> ......................................................103

■ Enable listening in multiple rooms (multi-zone function)

– Adjust Zone2/Zone3 volume <Zone2 Set/Zone3 Set> ..........................................................................104

– Display the Zone2/Zone3 menu on the TV <Monitor Out Assign>......................................................104

– Rename zones or scenes <Zone2 Scene Rename/Zone3 Scene Rename/Zone Rename>.....................105

■ Specify other functions for this unit

– Enter standby mode automatically when no operations are performed <Auto Power Down> .............106

– Assign jacks to the selected input source <Input Assignment> ............................................................106

– Adjust the brightness of the front panel display <Dimmer> .................................................................107

– Change the wall paper displayed on the TV screen <Wall Paper>........................................................107

– Specify the function of the TRIGGER OUT jack for controlling external components

<Trigger Output1/Trigger Output2> ......................................................................................................107

– Prohibit changes to settings <Memory Guard> .....................................................................................108

Adjust settings for each input source <Option menu>

– Adjust bass and treble levels <Tone Control> .........................................................................................60

– Enable low-volume background music <Adaptive DRC> ......................................................................60

– Enjoying more spatial sound fields <CINEMA DSP 3D Mode>............................................................60

– Adjust the vertical position of dialogues <Dialogue Lift> ......................................................................60

– Select the 5.1-channel signal playback method <Extended Surround> ..................................................60

– Adjust the volume of input sources <Volume Trim>...............................................................................61

– Selecting a video adjustment preset <Video Adjustment> ......................................................................61

– Selecting audio input jacks <Audio Select>............................................................................................61

– Shuffle or repeat playback <Shuffle/Repeat>..........................................................................................61

– Connect / Disconnect Bluetooth component to this unit <Connect/Disconnect> ...................................61

– Pairing Bluetooth component with this unit <Pairing> ...........................................................................61

INTRODUCTION

En 8

Front panel

a MAIN ZONE A (Power)

Switches this unit between on and standby mode.

b HDMI Through/iPod Charge indicator

Lights up in any of the following cases while the unit is in standby mode.

• When the Standby Through function is enabled and audio/video from

an external component connected with HDMI is output to a TV

during standby mode (☞

p. 102).

• When an iPod/iPhone, which is placed in the Universal Dock for iPod,

is charging while the unit is in standby mode (☞

p. 83).

This indicator also lights up when the Yamaha Wireless System for

iPod is connected to this unit (☞

p. 75).

c Front panel display

Displays information on this unit (☞

p. 11).

d PURE DIRECT

Switches this unit to Pure Direct Mode (☞

p. 53).

e INPUT selector

Selects an input source from which to playback. Rotate this selector to

cycle through the input sources in order.

f VOLUME

Adjusts the volume level.

Part names and functions

■ Opening and closing the front panel door

To use controls or jacks behind the front panel door, gently press

the bottom of the door to open it. Keep the door closed when not

using controls or jacks behind the front panel door.

Continues to the

e f

c db

INTRODUCTION

Part names and functions

En 9

Front panel with the cover opened

g ON SCREEN

Turns on and off the ON SCREEN menu.

h OPTION

Turns on and off the Option menu (☞

p. 58).

i TONE/BALANCE

Adjusts high-frequency/low-frequency output of speakers/headphones

in each zone (☞

p. 49, p. 131).

Adjusts the balance of the volume of the left and right channels in

Zone2 or Zone3 (☞

p. 131).

j STRAIGHT

Changes a sound program to straight decoding mode (☞

p. 52).

k PROGRAM l / h

Selects a sound program (☞

p. 51). Press the left or right key repeatedly

to cycle through sound programs.

l SCENE

Switches the input source, the sound program, and the HDMI OUT with

a single button (☞

p. 50, p. 84). When this unit is in standby mode,

press this key to switch on.

m MULTI ZONE

ZONE2

Switches to enable/disable the audio and video output to Zone2

(☞

p. 104, p. 129).

ZONE3

Switches to enable/disable the audio and video output to Zone3

(☞

p. 104, p. 130).

ZONE CONTROLS

Switches to Zone2 or Zone3 operation mode. This unit, or its remote

control, can be used to select input sources or adjust volume for an

external amplifier in another room or the built-in amplifier for speakers

in another room (☞

p. 131).

n INFO

Changes the information displayed on the front panel display (☞

p. 11).

o MEMORY

Registers FM/AM stations as preset stations (☞

p. 63). J1

p FM/AM

Sets the FM/AM tuner band to FM or AM (☞

p. 63). J1

q PRESET j / i

Selects an FM/AM preset station (☞

p. 64). J1

r Cursor B / C / D / E, ENTER, RETURN

s USB port

For connecting a USB memory device or portable USB audio player (☞

p. 39).

t DISPLAY

Switches the display between the Now Playing view and the Browse

view.

u YPAO MIC jack

Connect the supplied YPAO microphone and adjust the speaker balance

automatically (☞

p. 41).

v PHONES jack

For plugging headphones in. Sound effects applied during playback can

also be heard through the headphones.

w VIDEO AUX jacks

For connecting game consoles to this unit temporarily (☞

p. 36).

x TUNING/CH jj / ii

Changes FM/AM tuner frequencies (☞

p. 63). J1

Cursor B / C / D / E Select menu items and change settings when

menus, etc., are displayed.

ENTER Confirms a selected item.

RETURN Returns to the previous screen when menus are

displayed, or close the menu.

n

r

xt w

k

mg li o qnjh p

vus

J

1 : Usable when you have selected TUNER input.

INTRODUCTION

Part names and functions

En 10

Rear panel

a PHONO jacks

For connecting a turntable (☞

p. 35).

b DOCK jack

For connecting an optional Universal Dock for iPod (such as YDS-

12), Wireless System for iPod (YID-W10), or Bluetooth Wireless

Audio Receiver (YBA-10) (☞

p. 73, p. 75, p. 77).

c NETWORK port

For connecting to a network (☞

p. 38).

d HDMI OUT 1-2 jacks

For connecting an HDMI - compatible TV to output audio/video

signals (☞

p. 29).

e MON.OUT/ZONE OUT jacks (S-VIDEO/VIDEO jacks)

For connecting a TV capable of receiving video input, and outputting

video signals to it (☞

p. 29, p. 30).

f COMPONENT VIDEO jacks

For connecting external components that support component video

output for video signal reception (☞

p. 32).

g HDMI input jacks

For connecting external components equipped with HDMI-

compatible outputs to receive audio/video signals (☞

p. 31).

h MONITOR OUT/ZONE OUT jacks (COMPONENT VIDEO

jacks)

For connecting TV that are compatible with component video signals,

using three cables to output video signal (☞

p. 29).

i REMOTE IN/OUT1-2 jacks

For connecting an external component that supports the remote

control function (☞

p. 37).

j TRIGGER OUT 1-2 jack

For connecting an external component that supports the trigger

function to operate it linked with operation of this unit (☞

p. 37).

k RS-232C terminal

This is a control expansion terminal for custom installation. Consult

your dealer for details.

l AV1-4 jacks

For connecting to external components equipped with audio/video

outputs to receive audio/video signals (☞

p. 32).

m ANTENNA jacks

For connecting AM and FM antennas (☞

p. 40).

n AV OUT jacks

For outputting audio/video signals received when analog inputs are

selected (☞

p. 38).

o AUDIO1-4 jacks

For connecting external components equipped with audio outputs to

receive audio signals (☞

p. 35).

p MULTI CH INPUT jacks

For connecting a player that supports a multi-channel output

(☞

p. 36).

q ZONE OUT jacks

Outputs sound of this unit to an external amplifier set in a different

room. (☞

p. 129).

r PRE OUT terminals

For connecting a subwoofer with built-in amplifier or an external

power amplifier (☞

p. 23, p. 26).

s SPEAKERS terminals

For connecting the front, center, surround and surround back speakers

(☞

p. 20). Connect the presence speakers (☞p. 20) or the speakers for

Zone2 and Zone3 (☞

p. 21) to the EXTRA SP jacks.

t AC IN

For connecting the supplied power cable.

HDMI OUT

12

ZONE OUT PRE OUT

ZONE 2

AV OUT

YP

B

P

R

SURROUND

SUR. BACK

CENTER

(FRONT)

1

2

MON.OUT/ZONE OUT

ARC ARC

SELECTABLE

ZONE 3

(SINGLE)

ZO

NE2

/

Z

O

NE

3

SU

RR

OU

ND

SU

RR

OU

ND BA

C

K

/

S

PEAKER

S

C

ENTE

R

AV

1

AV

2

AV

3

AV

4

HDMI

AV

5

AV

6

AV

7

S

IN

G

LE

F

R

O

NT

BI

-

AMP

EXTRA SP

2

A

V

3

A

V 4

C

A

L

O

PTICA

L

A

UDIO 1

(2 TV)

(3 CD)

A

UDIO

2

A

UDIO

3

A

UDIO 4

FRONT

S

URROUND

S

UR. BAC

K

S

UBWOOFER

CENTER

MU

LTI

C

H INP

U

T

COMPONENT VIDEO

COAXIA

L

e

f

Y

P

B

P

R

Y

P

B

P

R

C

D

IN

1

2

1

OU

T

IN

OUT

R

EMOT

E

TRI

GG

ER

O

U

T

+12V 0.1A MA

(1 BD

/

DVD

)

AV 1

A

V

2

A

B

Distinguishing the input and output jacks

The area around the audio/video output jacks is marked

in white to prevent connection errors. Use these jacks to

output audio/video signals to a TV or other external

component.

Output jacks

EXTRA SP1

ZONE2/ZONE3

ANTENNA

75

AC IN

SURROUND SURROUND BACK/

SPEAKERS

CENTER

AV 1

HDMI OUT

AV 2 AV 3 AV 4

HDMI

AV 5 AV 6 AV 7

SINGLE

FRONT

BI-AMP

EXTRA SP2

12

PHONO

GND

(1 BD/DVD)

AV 1

DOCK NETWORK

AV 2 AV 3 AV 4

AV 3

AV 4

COAXIAL COAXIAL

OPTICAL OPTICAL

OPTICAL

AUDIO 1

(2 TV)

(3 CD)

AUDIO 2 AUDIO 3 AUDIO 4

FRONT

SURROUND

SUR. BACK

SUBWOOFER

CENTER

MULTI CH INPUT

COMPONENT VIDEO

COAXIAL

MONITOR OUT/ZONE OUT

ZONE OUT PRE OUT

ZONE 2

FRONT/

F. PRESENCE

AV OUT

abcd ef

YP

B

P

R

YP

B

P

R

YP

B

P

R

C

D

SURROUND

SUR. BACK

CENTER

(REAR)

(FRONT)

SUBWOOFER

1

2

RS-232C

IN

12

2

1

OUT IN OUT

REMOTE

TRIGGER

OUT

+12V 0.1A MAX.

MON.OUT/ZONE OUT

ARC ARC

SELECTABLE

ZONE 3

(SINGLE)

(1 BD/DVD)

AV 1

AV 2

A

B

ZONE2/ZONE3/

F.PRESENCE

GND

AM

FM

(4 RADIO)

bad g kjf

sl nmt

c

e h i

o p q r

INTRODUCTION

Part names and functions

En 11

Front panel display

a Tuner indicator

Light up according to the status of a received station (☞

p. 63).

b ZONE2/ZONE3 indicator

Lights up when the audio or video output to Zone2 or Zone3 is

enabled (☞

p. 131).

c SLEEP indicator

Blinks when the sleep timer is on (☞

p. 13, p. 131).

d PARTY indicator

Lights up when the party mode is active (☞

p. 104).

e Multi information display

Displays a range of information on menu items and settings.

f VOLUME indicator

Displays the current volume level.

g HDMI indicator

Lights up during normal HDMI communication.

IN indicator

Lights up when this unit detects the external component connected to

the HDMI input jack (☞

p. 31).

OUT 1/OUT 2 indicators

Indicate which HDMI OUT jack outputs audio/video signals

(☞

p. 29).

h ENHANCER indicator

Lights up when the Compressed Music Enhancer is active (☞

p. 53).

i CINEMA DSP indicator

Lights up when a sound field effect that uses CINEMA DSP

technology is selected.

j CINEMA DSP 3D indicator

Lights up when CINEMA DSP 3D is activated (☞

p. 52).

k Cursor indicators

Light up if corresponding cursors on the remote control are available

for operations.

l MUTE indicator

Blinks when audio is muted.

m Speaker indicators

Indicate speaker terminals from which signals are output.

n ADAPTIVE DRC indicator

Lights when the adaptive dynamic range control feature is tuned on

(☞

p. 60).

Surround L speaker

Subwoofer 1

Surround R speaker

Center speaker

Surround back L

speaker

Surround back R

speaker

Surround back

speaker J1

Presence L speaker Presence R speaker

Front L speaker Front R speaker

Subwoofer 2

■ Switching information on the front panel display

The front panel can display sound programs and surround

decoder names as well as the active input source.

Press tINFO repeatedly to cycle through displayed

informations. J2

VOLUME

AV1



Standard

Input source name

Sound program (DSP program)

STEREO

TUNED

PARTY

ENHANCER

SLEEP

MUTE

VOLUME

ADAPTIVE

DRC

be fa c

ihj mknlgk

d

J

1 : “SB” is displayed when using a 6.1-channel configuration only.

J

2 : During FM/AM reception, the frequency is displayed instead of the input source.

INTRODUCTION

Part names and functions

En 12

Remote control

a Remote control signal transmitter

Transmits infrared signals.

b SOURCE A (SOURCE Power)

Switches an external component on and off.

c Display window

Displays remote control information.

d Input selector

Select an input source on this unit from which to playback.

e SCENE

Switch the input source and the sound program with a single button

(☞

p. 50). When this unit is in standby mode, press this key to switch

on.

f PROGRAM k / n

Selects a sound program (☞

p. 51). Press the up or down key

repeatedly to cycle through sound programs.

g External component operation keys

Operate recording, playback, and menu displays etc. for external

components (☞

p. 111). J1

h ON SCREEN

Turns on and off the ON SCREEN menu.

i Cursor B / C / D / E, ENTER, RETURN

j PRESET F / G

Selects a preset station when the FM/AM tuner is operated.

k TV control keys

Operate a monitor such as a TV.

l RECEIVER A (RECEIVER Power)

Switches this unit between on and standby mode.

m SOURCE/RECEIVER

Switches remote control key function to operate this unit or an

external component (☞

p. 111). Operate an external component when

this key glows green, or this unit when this key glows orange.

n VOLUME +/-

Adjust the volume level (☞

p. 48).

o MUTE

Turns the mute function of the sound output on and off (☞

p. 48).

p OPTION

Turns on and off the Option menu (☞

p. 58).

q DISPLAY

Switches the display between the Now Playing view and the Browse

view.

r Sound selection keys

Switch between the current sound field effect (sound program) and the

surround decoder (☞

p. 51).

LIVE

CLUB

CLASSICAL

PRESET

ENTERTAIN

STEREO

MOVIE

STRAIGHT

2

3

SOURCE

RECEIVER

AV

AUDIO

SCENE

TV

TV VOL TV CH

MUTE

RETURN DISPLAY

TOP MENU

POP-UP/MENU

VOLUME

PROGRAM

1

PURE

DIRECT

MUTE

INPUT

4

31

2

75

6

V-AUX

4

31

2

USB

MULTI

NET

PHONO

TUNER

DOCK

4

REC

ON SCREEN

OPTION

ENTER

[ B ]

[ A ]

a

c

b

h

i

p

q

n

j

k

f

m

o

l

d

e

g

r

AV1-7 AV1-7 jacks

V-AUX Front panel VIDEO AUX jacks

AUDIO1-4 AUDIO1-4 jacks

PHONO PHONO jacks

MULTI MULTI CH INPUT jacks

USB A USB storage device connected to the USB port.

NET Internet radio, a USB connected to the USB port,

or a PC connected to the NETWORK port.

DOCK A Universal Dock for iPod, Wireless System for

iPod, or Bluetooth Wireless Audio Receiver

connected to the DOCK jack.

TUNER FM/AM tuner

[A]/[B] Changes the external component to operate with

the gExternal component operation keys

without changing inputs. J1

Cursor B / C / D / E Select menu items and change settings when

menus, etc., are displayed.

ENTER Confirms a selected item.

RETURN Returns to the previous screen when menus are

displayed, or close the menu.

J

1 : You can use gExternal component operation keys for each input source to operate registered components. Remote control codes must be registered for each input

in advance if you want to operate external components (☞

p. 113).

INTRODUCTION

Part names and functions

En 13

Remote control with the cover open

s Sound selection keys

Switch between the current sound field effect (sound program) and the

surround decoder (☞

p. 51).

t INFO

Cycles the information displayed on the front panel display (the name

of the currently selected input source, the sound program, the

surround decoder, the FM/AM tuner frequency, etc.).

u Numeric keys

Enter numbers.

v PARTY

Switches the party mode on and off (☞

p. 131).

w HDMI OUT

Switches the output jack connected to an HDMI compatible TV

(☞

p. 48).

x Radio control keys

Operates the FM/AM tuner. These keys are used when using the tuner

input.

y SLEEP

Switches this unit to standby mode automatically after a specified

period of time has elapsed (sleep timer). Press this key repeatedly to

set the time for the sleep timer function.

The SLEEP indicator lights up when the sleep timer is on.

z LEVEL

Adjusts the output level for each speaker (☞

p. 96).

A SETUP

Setup this remote control (☞

p. 112).

B ZONE

Switches the zone to be operated by the remote control between the

Main zone, Zone2, and Zone3 (☞

p. 131).

2

3

SOURCE

RECEIVER

AV

AUDIO

SCENE

MUTE

RETURN DISPLAY

TOP MENU

POP-UP/MENU

VOLUME

PROGRAM

1

4

31

2

75

6

V-AUX

4

31

2

USB

MULTI

NET

PHONO

TUNER

DOCK

4

ON SCREEN

OPTION

ENTER

FM

MEMORY

AM

INFO

3

TUN./CH

21

6

9

8

SLEEP

7

ENT

0

LEVEL

10

PARTY

ENHANCER

HDMI OUT

SUR.

DECODE

ZONE

SETUP

4

5

[ B ]

[ A ]

t

u

s

x

y

w

z

A

B

v

MEMORY Presets radio stations.

FM Sets the FM/AM tuner band to FM.

AM Sets the FM/AM tuner band to AM.

TUN./CH H / I Changes tuning frequencies.

120min. 90min.

60min.30min.Off

■ Installing batteries in the remote control

When inserting batteries in the remote control, remove the

battery compartment cover from the reverse side of the remote

control, and insert four AAA batteries into the battery

compartment so that they match with the polarity markings (+

and -).

Replace the batteries with new ones if the remote control can

only be operated within a narrow range.

NOTE

If there are remote control codes for external components

registered to the remote control, removing the batteries for more

than 2 minutes, or leaving exhausted batteries in the remote

control, may clear the remote control codes. If this should occur,

replace the batteries with new ones, and set the remote control

codes.

b

a

c

Battery compartment

cover

Battery compartment

INTRODUCTION

Part names and functions

En 14

On-screen display

When a TV is connected to this unit, the supplied remote control can be used to specify and verify this

unit’s settings via menus and options displayed on the TV screen.

The following displays are available in the on-screen display.

ON SCREEN menu

Press hON SCREEN to display the ON

SCREEN menu.

Detailed settings for this unit can be

configured. Use this menu to select desired

settings, change their values, or check the

current status of this unit.

Refer to “SETUP” (☞

p. 81) for details.

Option menu

Press pOPTION to display the Option menu.

Configure the optional settings for each input

source. Settings such as “Tone Control” and

“Volume Trim” are applied to this unit

regardless of the input source.

Refer to “Configuring settings specific to an

individual input source (Option menu)”

(☞

p. 58) for details.

Content window

Press dInput selector to display the content

window.

Includes the Browse view and the Now

Playing view. The Now Playing view displays

the status of the source from which music is

currently played back. Adjust settings for

music content from the Browse view.

Refer to “Confirming and operating input

sources from the content window” (☞

p. 62)

for details.

En 15

CONNECTIONS

This unit uses acoustic field effects and sound decoders to bring you the impact of a real movie theater or concert hall. These effects will be brought to you with ideal speaker positioning and

connections in your listening environment.

Speaker channels and functions

■

Front left and right speakers

The front speakers are used for the front channel sounds (stereo

sound) and effect sounds.

Front speaker layout:

Place these speakers at an equal distance from the ideal listening

position in the front of the room. When using a projector screen,

the appropriate top positions of the speakers are about 1/4 of the

screen from the bottom.

■

Center speaker

The center speaker is for the center channel sounds (dialogue,

vocals, etc.).

Center speaker layout:

Place it halfway between the left and right front speakers. When

using a TV, place the speaker just above or just under the center of

the TV with the front surfaces of the TV and the speaker aligned.

When using a screen, place it just under the center of the screen.

■

Surround left and right speakers

The surround speakers are for effect and vocal sounds while

playing back more than 5.1-channel source. When used with no

surround back speaker while playing back more than 6.1-channel

source (including surround back channel), sound of surround back

channel is distributed between the left and right surround speakers.

Surround speaker layout:

Place the speakers at the rear of the room on the left and right sides

facing the listening position. They should be placed between 60

degrees and 80 degrees from the listening position and with the

speaker tops at a height of 1.5 – 1.8 m from the floor.

■

Presence left and right speakers

The presence speakers are used for front effect sounds. When used

in combination with the sound programs (☞

p. 54), a sound with a

richer and more spatial presence is possible.

Presence speaker layout:

Place the left and right presence speakers 0.5 – 1 m to the outside

of the left and right front speakers respectively. The tops of the

presence speakers should be 1.8 m above the floor.

■

Surround back left and right speakers

The surround back speakers are for rear effect sounds while

playing back more than 6.1-channel source. When used with only

one surround back speaker while playing back more than 7.1-

channel source, sound of the left and right surround back channel is

mixed and output from a single speaker.

Surround back speaker layout:

When used with 7.1ch sound, arrange the left and right speakers

towards the listening position, to the rear of the listening position.

Arrange the left and right speakers at least 30 cm apart. The same

separation as with the front left and right speakers is optimum.

When used with 6.1ch sound, arrange these to the rear of the

listening position.

■

Subwoofer

The subwoofer speaker is used for bass sounds and low-frequency

effect (LFE) sounds included in Dolby Digital and DTS. Use a

subwoofer that is equipped with built-in amplifier.

Subwoofer speaker layout:

Place it to the outside of the front left and right speakers facing

slightly inward to reduce echoes from the wall. You can use one or

two subwoofers and select the position of subwoofers from “Left +

Right,” “Front + Rear” and “Monaural x2” (☞p. 95).

Connecting speakers

E.g.

CONNECTIONS

Connecting speakers

En 16

Speaker layout

In addition to the 7.1-channel speaker layout, a variety of speaker configurations can be specified with

presence speaker connection, bi-amp connection or the Zone2/Zone3 function.

In addition, this unit is equipped with the “Power Amp Assign” function, which can be used to easily

apply the appropriate speaker settings to this unit according to speaker configuration.

■

Connection of speakers

Connect the speakers to the appropriate jacks shown in the table for each speaker layout. Refer to

“Connecting speakers and subwoofers” (☞

p. 20) for details on connecting speakers.

You can also use two subwoofers by connecting them to both SUBWOOFER1 (FRONT) and

SUBWOOFER2 (REAR) jacks. And, you can use the EXTRA SP1 jacks for Zone3 speakers and

EXTRA SP2 jacks for Zone2 by setting the assignment with “Power Amp Assign” (☞

p. 94).

■

Assigning a speaker configuration

A speaker configuration must be assigned to this unit to activate the speakers. Use the Power Amp

Assign function to apply the appropriate settings shown in the table for each speaker layout. Refer to

“Power Amp Assign” (☞

p. 94) for details on setting.

■

Enjoying the 7.1 channel audio source

■ 7.1-channel speaker layout (7 speakers + subwoofer)

■ Connections of speakers

■ Assigning a speaker configuration

Audio from a 7.1-channel audio source can be played back with no degradation with this speaker

configuration.

FRONT jacks Front L/R speakers SURROUND

BACK jacks

Surround back L/R speakers

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

SURROUND jacks Surround L/R speakers

Power Amp Assign 7ch Normal (Default)

Front L speaker

Front R speaker

Subwoofer

Center speaker

Surround L speaker

Surround R

speaker

Surround back R speaker

Surround back L speaker J1

30 cm

or more

J

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

CONNECTIONS

Connecting speakers

En 17

■

Adding the presence speakers for a richer sound field effect

■ Presence speaker layout (7 speakers + subwoofer + presence speakers)

■ Connections of speakers

■ Assigning a speaker configuration

■

Enjoying the audio source without surround back speakers

■ 5.1-channel speaker layout (5 speakers + subwoofer)

■ Connections of speakers

■ Assigning a speaker configuration

This unit automatically selects the presence speakers or surround back speakers to output sounds

according to the selected sound program.

When the sound program is changed, the speakers that output the sound are switched between the

presence speakers and surround back speakers automatically. J2

FRONT jacks Front L/R speakers SURROUND

BACK jacks

Surround back L/R speakers

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

SURROUND jacks Surround L/R speakers EXTRA SP1 jacks Presence L/R speakers

Power Amp Assign 7ch Normal (Default)

Front L

speaker

Front R speaker

Subwoofer

Center speaker

Surround L speaker

Surround R

speaker

Presence R speaker

Presence

L speaker

Surround back

R speaker

Surround back L speaker J1

30 cm

or more

This unit can mix 7.1-channel audio source down to 5.1-channel sound. This enables 7.1-channel

sound without surround back speakers.

FRONT jacks Front L/R speakers SURROUND jacks Surround L/R speakers

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

Power Amp Assign 7ch Normal (Default)

Front L speaker

Front R speaker

Subwoofer

Center speaker

Surround L speaker

Surround R

speaker

J

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

J

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

CONNECTIONS

Connecting speakers

En 18

■

Using the front speakers that support bi-amp connections for a

high quality sound

■ 5.1-channel speaker layout (Front speakers (Bi-amp) + 3 speakers)

■ Connections of speakers

■ Assigning a speaker configuration

■

Using speakers in two rooms (Zone2 function)

■ 7.1-channel speaker layout + Zone2 (7 speakers (in main zone) + subwoofer (in

main zone) + front speakers (in secondary zone))

■ Connections of speakers

■ Assigning a speaker configuration

Using the front speakers that support bi-amp connections reproduces a high quality sound.

FRONT jacks Front L/R speakers (bi-amp) SURROUND

BACK jacks

Front L/R speakers (bi-amp)

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

SURROUND jacks Surround L/R speakers

Power Amp Assign 5ch BI-AMP

Front L speaker

(Bi-amp connection)

Front R speaker

(Bi-amp connection)

Center speaker

Surround L speaker

Surround R

speaker

Subwoofer

In addition to the main room, speakers in another room can also be controlled.

When the built-in amplifier assigned to speakers in another room is turned on, sound output

automatically switches from the surround back speakers to the speakers in the other room. J2

FRONT jacks Front L/R speakers SURROUND

BACK jacks

Surround back L/R speakers

CENTER jack Center speaker SUBWOOFER

(PRE OUT) jack

Subwoofer

SURROUND jacks Surround L/R speakers EXTRA SP1

jacks J3

Zone2 speakers

Power Amp Assign 7ch + 1ZONE

Front L speaker

Front R speaker

Center speaker

Subwoofer

Surround R speaker

Surround L speaker

Surround back L speaker J1

Surround back R

speaker

30 cm

or more

Front R speaker

Front L speaker

Main zone Zone2

J

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

J

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

J

3 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 94).

CONNECTIONS

Connecting speakers

En 19

■

Using speakers in three rooms (Zone2 and Zone3 functions)

■ 7.1-channel speaker layout + Zone2 + Zone3 (7 speakers (in main zone) +

subwoofer (in main zone) + front speakers (in secondary and tertiary zones))

■ Connections of speakers

■ Assigning a speaker configuration

In addition to the main room, speakers in other two rooms can also be controlled.

When the built-in amplifier assigned to speakers in another room is turned on, sound output

automatically switches from the surround back and/or surround speakers to the speakers in the other

rooms. J2, J3

Front L speaker

Front R speaker

Center speaker

Subwoofer

Surround R

speaker

Surround L speaker

Surround back L speaker J1

Surround back

R speaker

30 cm

or more

Zone2

Zone3

Front R

speaker

Front R

speaker

Front L speaker

Main zone

FRONT jacks Front L/R speakers SUBWOOFER

(PRE OUT) jack

Subwoofer

CENTER jack Center speaker EXTRA SP1

jacks J4

Zone2 speakers

SURROUND jacks Surround L/R speakers EXTRA SP2

jacks J5

Zone3 speakers

SURROUND

BACK jacks

Surround back L/R speakers

Power Amp Assign 7ch + 2ZONE

J

1 : The sound of surround back channel can also be output from a single surround back speaker. When only one surround back

speaker is used, connect it to the SURROUND BACK L (SINGLE) jack and place it directly behind the listening position.

J

2 : Sound cannot be output from the surround back speakers when it is output from the speakers connected to the EXTRA SP1

jacks.

J

3 : Sound cannot be output from the surround speakers when it is output from the speakers connected to the EXTRA SP2 jacks.

J

4 : EXTRA SP1 jacks can also be assigned to the Zone3 speakers with “Power Amp Assign” (☞p. 94).

J

5 : EXTRA SP2 jacks can also be assigned to the Zone2 speakers with “Power Amp Assign” (☞p. 94).

CONNECTIONS

Connecting speakers

En 20

Connecting speakers and subwoofers

Connect your speakers to their respective terminals on the rear panel.

■ Front/Center/Surround/Surround back speaker and

Subwoofer connection

When connecting only one surround back speaker, connect the

speaker to the SURROUND BACK L (SINGLE) jacks.

■ Presence speaker connection

When using the presence speakers, connect the speakers to the

EXTRA SP1 jacks as shown in the diagram below.

The presence speakers (PL/PR) that output front effect sounds can

be connected to this unit. With the sound programs (☞

p. 58),

sound with a richer and more spatial presence can be created.

CAUTION

• Remove the power cable of this unit from the power outlet before connecting the speakers.

• Generally speaker cables consist of two parallel insulated cables. One of these cables is a different color, or has a line running along it, to indicate different polarity. Insert the different colored (or lined) cable into the “+”

(positive, red) terminal on this unit and the speakers, and the other cable into the “–” (negative, black) terminal.

• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of this unit. This may damage this unit or the speakers. If the speaker cables short circuit, “CHECK SP

WIRES!” will appear on the front panel display when this unit is switched on.

SURROUND SURROUND BACK/

CENTER

SINGLE

FRONT

BI-AMP

(FRONT)

1

A

V 2

A

V

3

A

V 4

HDMI

A

V

5

A

V

6

A

V

7

AV

3

AV 4

U

RROUN

D

SUR. BACK

S

UBWOOFE

R

C

ENTER

M

ULTI

C

H INPU

T

O

MP

O

NENT VIDE

O

MONITOR OUT/ZONE OUT

Z

O

NE

OUT

PRE

OUT

ZO

NE 2

F

RONT

/

F. PRE

S

EN

C

E

Y

P

B

P

R

P

R

Y

P

B

P

R

C

D

S

URROUN

D

S

UR. BACK

CENTE

R

(

REAR

)

SUBWOOFER

()()

2

R

S

-2

3

2

C

IN

1

2

1

OUT

IN

OU

T

R

EMOTE

TRIGGE

R

O

UT

+

12V

0

.1A MAX

.

E

XTRA

S

P1

ZO

NE

3

(SINGLE)

DVD

)

ZO

NE2

/

Z

ON

F.P R E

S

E

N

Subwoofer

Center speaker

Front speaker

Surround

speaker

Surround back

speaker

RL

RL RL

EXTRA SP1

ZONE2/ZONE3/

F.PRESENCE

A

C

IN

C

ENTE

R

AV

6

AV 7

F

RON

T

U

R. BA

CK

C

ENTE

R

(

REAR

)

(FRONT)

SUBWOOFER

()()

1

2

RS-232C

IN

1

2

1

O

U

T

I

N

O

UT

R

EMOTE

TRI

GG

E

R

O

UT

+

12

V

0

.1

A

MAX.

SINGLE)

Presence speaker

RL

Connection of presence speakers is recommended to take full

advantage of the effects of CINEMA DSP sound programs.

0.5 – 1 m 0.5 – 1 m

PL PR

LR

1.8 m 1.8 m

Continues to the

Sivu latautuu ...

Yamaha RX-A2000 Omistajan opas

Yamaha RX-A2000 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat