Yamaha TSX-B15 Omistajan opas

G

En Fr De

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

Sv It Es

Nl

Ru

i En

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place - away from direct sunlight, heat sources,

vibration, dust, moisture and cold. For proper

ventilation, allow the following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in an environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit,

and/or personal injury. Yamaha will not be held

responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power

cable disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press to set the system to

off, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the system off, then leave this

unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 Be sure to use the AC adaptor supplied with this unit.

Using an AC adaptor other than the one provided

may cause fire or damage to this unit.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off by . In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

• This unit’s speakers use magnets. Do not place items

that are sensitive to magnetism, such as CRT-type TVs,

clocks, credit cards, floppy disks, etc., on or beside this

unit.

• There is a chance that placing this unit too close to a

CRT-based (Braun tube) TV set might impair picture

color. Should this happen, move this unit away from the

TV set.

Do not use this unit within 22 cm (9 inches) of persons

with a heart pacemaker implant or defibrillator implant.

Radio waves may affect electro-medical devices.

Do not use this unit near medical devices or inside

medical facilities.

We, Yamaha Music Europe GmbH hereby

declare that this unit is in compliance with the

essential requirements and other relevant

provisions of Directive 1999/5/EC.

Yamaha Music Europe GmbH

Siemensstr. 22-34 25462 Rellingen, Germany

Tel: +49-4101-303-0

1 En

En

PREPARATION

NAMES OF PARTS AND THEIR FUNCTIONS .................................................................................... 2

BASIC FUNCTIONS................................................................................................................................... 4

LISTENING TO FM STATIONS.............................................................................................................. 6

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE ................................................................ 7

LISTENING TO EXTERNAL SOURCES ............................................................................................. 10

CHARGING WITH THE USB PORT .................................................................................................... 10

TROUBLESHOOTING ............................................................................................................................ 11

SPECIFICATIONS ................................................................................................................................... 13

■ Features

– Playback of Bluetooth devices, FM radio, and external devices with an AUX connector.

– Setting alarm using an FM radio.

– Supplying power to smartphones, tablets, etc. via USB port on the rear panel.

– Rich sound by 5cm full-range custom speaker and DSP (Digital Signal Processor) made by Yamaha.

– Enhanced treble and thick mid/bass, even when playing a compressed audio source, such as MP3, etc.

(Music Enhancer)

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

■ Supplied accessories

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection

points, in accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

Note

y

AC adaptor FM antenna

DC 12 V, 1.5 A,

model number:

MU18-D120150-C5

CONTENTS

2 En

■ Top panel

NAMES OF PARTS AND THEIR FUNCTIONS

G Display

H Indicators

(Alarm): Lights when the alarm

function is on (☞ page 4).

RADIO: Lights when the radio is selected

as an input source (☞ page 6).

AUX: Lights when AUX is selected as an

input source (☞ page 10).

(Bluetooth):Lights when ( ) Bluetooth

is selected as an input

source or during Bluetooth

pairing/connection

(☞ page 7, 9).

J

Press to turn on the system or enter standby mode.

Eco Standby mode

• This can reduce power consumption. Press and hold for

more than 3 seconds to set the system to power saving mode.

All the indicators and display turn off, and Bluetooth operation,

audio playback, input via buttons except are disabled. To

cancel Eco Standby mode, press .

• Even in standby mode or Eco Standby mode, the alarm

function is available.

Auto Standby (☞ page 5)

• This unit has a function that automatically activates standby

mode when no audio signal is input from a connecting device,

or when the connecting device is playing at a low volume for a

certain period (about 20 minutes).

y Dimmer function

Press CLOCK repeatedly to set the

brightness of the display and indicators.

3 (brightest) 2 1 (darkest)

I Grille (☞ page 3)

A VOLUME

Controls volume. When you

control the volume, the volume

level will be displayed on the

display for a while.

B CLOCK

Sets the clock (☞ page 4).

C ALARM

Sets the alarm (☞ page 4).

D TUNING

Adjust the time or radio frequency

(☞ page 4, 6).

E PRESET

Stores up to five favorite FM radio

stations (☞ page 6).

F SOURCE (PAIRING)

Selects an input source from

(Bluetooth), AUX, or RADIO.

NAMES OF PARTS AND THEIR FUNCTIONS

3 En

En

■ Rear panel

A grille is attached to this product to protect the speakers.

• Since the grille cloth is made of soft material, it can be easily damaged, so do not scratch it with a sharp object.

• Do not overstress the grille cloth. If it is overstressed, it will become contorted and damaged. This may cause damage to

the speakers. Be careful when handling the grille cloth.

Connecting the FM antenna

A Connect the supplied antenna to the

unit.

B Pin the antenna where the best

reception is obtained.

• Be sure to stretch out the antenna as the illustration shows.

• If FM reception is poor, change the height or direction of

the antenna, or relocate the unit.

If you listen to an FM radio station while USB charging,

noise may interfere with the radio reception. In this case,

disconnect the USB cable from the unit.

Caution

K CHARGING

Supplies 5 V/1 A to a

portable device, such as

a smartphone, when it is

connected with a USB

cable (☞ page 10).

L 12 V

Connect the

supplied AC

adaptor.

M AUX

Connect external devices

with ø3.5mm stereo mini

plug cables (☞ page 10).

N FM ANT

FM antenna terminal

To AC wall outlet

A

B

Note

Caution

4 En

OPERATION

This unit can play back the radio and emit beeps at the set time.

■ Setting the time and sound

BASIC FUNCTIONS

Adjusting the clock

A Press and hold CLOCK for more than

2 seconds.

The display flashes.

B Adjust the time with TUNING.

y

If you press and hold TUNING, the numbers

advance quickly.

C Press CLOCK.

If you want to cancel clock setting mode, press .

y

If you press PRESET in step B, you can select the

time display method (12 hours/24 hours).

The time settings are lost approximately one week after

unplugging the unit.

Alarm setting

A Press and hold ALARM for more than

2 seconds.

The alarm indicator ( ), the RADIO

indicator and display flash.

B

Set the alarm time with

TUNING

.

C Set the alarm volume with VOLUME.

The volume level is displayed.

D Press ALARM.

Alarm is set and the alarm indicator ( ) lights.

y

• The alarm type of this unit is the radio and beeping

only.

• The radio turns on 3 minutes before the alarm time

and beeping starts at the alarm time.

If you press ALARM to complete the setting of the alarm

without changing the alarm time and volume, the alarm

setting mode will be cancelled and the alarm will not be set

to on.

A

,

C

B

Note

A

,

D

C

B

RADIO indicator

Alarm

indicator

()

Note

BASIC FUNCTIONS

5 En

En

■ Switching the alarm on/off

At the set time, alarm sound plays back. During playback, operations below are available.

■ Stopping the alarm

The system automatically enters standby mode under the following circumstance.

• No audio signal is input from a connecting device or when the connecting device is playing at a low volume

for a certain period (about 20 minutes).

• If no operation is performed for more than 8 hours while music is being played back or stopped.

• Disconnect the Bluetooth connection from the Bluetooth device.

Press ALARM.

When the alarm is on, the alarm indicator ( )

and the RADIO indicator light and the alarm time is

displayed for a while.

Alarm

indicator

()

RADIO indicator

Operations during playing back alarm sound

Press ALARM or .

y

• Unless you stop the alarm, the alarm stops after

60 minutes automatically.

• When you stop the alarm, the alarm time setting, etc., is

saved for convenient use next time.

• Press any button except ALARM and once to stop the

beeping, and twice to stop the radio source (snooze

function). 4 minutes after the radio source is stopped, it

will start fading in again and after another minute the

beeping will resume.

• When the snooze function is activated, the display, alarm

indicator ( ) and RADIO indicator flash.

RADIO indicator

Alarm

indicator

()

Auto Standby

6 En

You can store up to five favorite FM radio stations with the preset function.

LISTENING TO FM STATIONS

Tuning radio stations

A Press SOURCE to select RADIO.

The RADIO indicator lights.

B For automatic tuning, press and hold

TUNING.

For manual tuning, press TUNING

repeatedly.

If you tune into a station manually, the sound is monaural.

Presetting radio stations

A Press TUNING to select a favorite radio

station.

The radio frequency is displayed temporally.

B Press and hold PRESET for more than

2 seconds.

The preset number is displayed on the display and

flashes.

C Press PRESET to select the preset

number you want to store to.

The preset number is displayed as follows:

P1

P2 P3 P4 P5 P1

D Press and hold PRESET for more than

2 seconds to complete.

Selecting preset radio stations

A Press SOURCE to select RADIO.

The RADIO indicator lights.

B Press PRESET repeatedly to select the

preset radio station.

A

B

RADIO indicator

Note

A

B

,

C

,

D

RADIO indicator

B

A

RADIO indicator

7 En

En

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device

(smartphone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.

• This unit can be paired with up to four connecting devices. When pairing with the fifth device has succeeded, pairing data for

the device with the oldest connection date will be deleted.

• If this unit is connected via Bluetooth to another device, press and hold SOURCE to disconnect the Bluetooth connection

before you perform the pairing operation.

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

Installation

Install in a stable place, being careful of

the following points:

• Do not place on top of steel or other

metal plates.

• Do not cover with a cloth, etc.

• Install in the same room as the device

with which signals are to be exchanged

(Bluetooth profile A2DP compatible

smartphone, digital audio player, etc.)

within a direct line-of-sight distance of

10 m (33 ft).

• Make sure there are no obstacles

between this unit and the Bluetooth

device.

Within 10 m (33 ft)

Pairing this unit with your Bluetooth device

y What is pairing?

Pairing is an operation that registers the communicating device (subsequently called “the connecting

device”) with this unit. You will need to perform the pairing operation the first time you use your Bluetooth

device with this unit, or if the pairing settings have been deleted. Once pairing has been completed,

subsequent reconnection will be easy even after the Blu etooth connection is disconnected. If pairing is not

successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (☞ page 12).

Note

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

8 En

■ Pairing (Registration)

– If using an iPhone/iPad/iPod touch

– If using other than an iPhone/iPad/iPod touch

A

Turn on the system.

B Press and hold SOURCE for more than

2 seconds to enter paring mode.

• Pairing mode lasts for 5 minutes.

• In paring mode, the Bluetooth indicator ( ) will light in

orange and blue alternately.

C On your iPhone/iPad/iPod touch, turn

[Settings] [Bluetooth] on.

The Bluetooth connection list will appear in

[Devices].

(This procedure or display may differ depending

on the type of your iPhone/iPad/iPod touch.)

D From the Bluetooth connection list of the

connecting device, choose this unit

(TSX-B15 Yamaha).

• When pairing has been completed, your iPhone/iPad/

iPod touch will indicate “Connected”.

• The Bluetooth indicator ( ) will light in blue.

C Perform Bluetooth pairing on the

connecting device.

For details, refer to the owner’s manual of the

connecting device.

D From the Bluetooth connection list of the

connecting device, choose this unit

(TSX-B15 Yamaha).

When pairing has been completed, the Bluetooth

indicator ( ) will light in blue.

y

If you are prompted for a passkey, enter the numerals “0000”.

B

A

Bluetooth indicator ( )

TSX-B15 Yamaha

C

D

Within about 5 minutes

TSX-B15 Yamaha

PIN 0000

123

456

789

0

C

D

Within about 5 minutes

Check that the pairing process on the connecting device has been completed. If the pairing process fails,

start over from step B. For details, see the connecting device’s operating instructions.

Note

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

9 En

En

Once pairing with a device has been completed, connecting with that device via Bluetooth will be easy next

time.

■ Connecting from this unit

Press SOURCE to select (Bluetooth).

The Bluetooth indicator ( ) will light in orange.

This unit will search for the connecting device that was most recently connected via Bluetooth, and will then

establish a connection (You must first turn on the Bluetooth setting of the connecting device).

When the Bluetooth connection has been established, the Bluetooth indicator ( ) will light in blue.

Yamaha does not guarantee all connections between this unit and Bluetooth device.

■ Connecting from the connecting device

A In the Bluetooth settings of the connecting device, turn Bluetooth on.

B From the Bluetooth connection list of the connecting device, choose this unit (TSX-B15

Yamaha).

The Bluetooth connection will be established, and the Bluetooth indicator ( ) will light in blue.

Bluetooth connections cannot be established from the connecting device when this unit is in Eco Standby mode. Turn the

system on.

If any of the following operations are performed while a Bluetooth connection is established, the Bluetooth

connection will be disconnected.

• Press and hold SOURCE for more than 2 seconds.

• Press SOURCE to select a playback source other than (Bluetooth).

• Press to enter standby mode.

• Disconnect the Bluetooth connection from the Bluetooth device.

Listening to a Bluetooth device

A

Press

SOURCE

to select (Bluetooth).

B Connect this unit and your connecting

device via Bluetooth.

C Play back music from your connecting

device.

Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the connecting

device.

y

• While the system is in standby mode, if you connect a

Bluetooth device to the unit, the system will automatically

turn on.

• If you disconnect the Bluetooth connection from the

connecting device, the system will enter standby mode.

Connecting an already-paired device via Bluetooth

A

Note

Disconnecting a Bluetooth connection

10 En

Connecting a portable device such as a smartphone or tablet computer to the USB port on this unit charges the

connected device (power supply of up to 5 V/1 A is supported).

Prepare a USB cable that is compatible with the portable device and confirm that the device is supported for

charging via USB connection before use. In addition, read the documentation provided with the portable

device.

LISTENING TO EXTERNAL SOURCES

A Connect your portable audio

device to AUX using a

commercially available 3.5 mm

(1/8 in) mini plug cable.

Turn down the volume of this unit and your

portable audio device before connection.

B Turn on the system.

C Press SOURCE to set the

playback source to AUX.

The AUX indicator lights.

D

Start playback on the connected

portable audio device.

CHARGING WITH THE USB PORT

A

Connect your portable device

to the USB port on this unit

using a commercially available

USB cable.

Charging automatically starts.

B Disconnect the USB cable

from the unit when charging

completes.

Check the charging status on the

portable device.

• The USB port is for charging use only. The

USB port does not support audio playback.

• Charging may not be possible depending on

the portable device.

• In Eco Standby mode, power supply stops,

and charging is not available.

• This unit does not function as memory

storage.

• Yamaha will not be held responsible for any

damage to the portable device or data loss

occurred while using this unit.

• Disconnect the USB cable immediately after

charging completes, since power continues to

be supplied to the connected device.

A

C

B

Rear panel

AUX indicator

Note

USB cable from

portable device

Rear panel

Note

11 En

En

Refer to the table below if the unit does not operate properly. If the problem you are experiencing is not listed

below, or if the instruction below does not help, press to enter standby mode, disconnect the power cable,

and contact the nearest authorized Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Solution

The speakers make no

sound.

The volume may be set to the minimum

level.

Adjust the volume level.

The source may be incorrect. Select the correct source.

The unit is setting the alarm. Press ALARM to complete the alarm setting.

Sound suddenly turns off.

Auto Standby function is enabled. Turn on the system and play the source again.

Since the connecting device outputs at a

very low volume, the Auto Standby

function is enabled.

Raise the volume of the connecting device.

Sound is cracked/

distorted or there is

abnormal noise.

Input source volume is excessive, or

volume of this unit is excessive.

Adjust the volume with VOLUME.

The unit does not operate

properly.

The unit may have received a strong

electrical shock such as lightning or

excessive static electricity, or power

supply may have dropped.

Press to enter standby mode and

disconnect the power cable. Wait about

30 seconds, reconnect the power cable, and

turn on the system.

The system turns on but

immediately shuts off.

The power cable may be connected

improperly.

Make sure the power cable is plugged into the

wall outlet firmly.

The unit may have received a strong

electrical shock such as lightning or

excessive static electricity.

Disconnect the power cable. Wait about

30 seconds, reconnect the power cable, and

turn on the system.

A digital or high-frequency

equipment produces

noises.

The unit may be placed too close to the

digital or high-frequency equipment.

Place the unit farther away from the

equipment.

The clock setting has been

cleared.

The unit is left more than one week after

you disconnect the power cable from the

wall outlet.

Plug the power cable into the wall outlet

firmly, and set the clock again (☞ page 4).

The clock flashes.

The unit is setting CLOCK or ALARM. Press to cancel setting CLOCK or

ALARM.

FM radio reception

Problem Cause Solution

Too much noise during

stereo broadcast.

The radio station you selected may be far

from your area, or the radio wave

reception is weak in your area.

Try manual tuning to improve the signal

quality (☞ page 6) or change the height or

direction of the antenna, or relocate the unit

(☞ page 3).

TROUBLESHOOTING

12 En

Bluetooth

Problem Cause Solution

Cannot make this unit

paired with the connecting

device.

The connecting device does not support

A2DP.

Perform pairing operations with a device

which supports A2DP.

The passkey of the connecting device that

you want to pair with this unit is a passkey

other than “0000”.

Use a connecting device with a passkey

“0000”.

This unit and the connecting device are

too far apart.

Move the connecting device closer to this

unit.

There is a device (microwave oven,

wireless LAN, etc.) that outputs signals in

the 2.4 GHz frequency band nearby.

Move this unit away from the device that is

emitting radio-frequency signals.

The unit is in standby mode.

Turn the unit on and perform paring (

☞

page 8).

Another Bluetooth device is connected. Terminate current Bluetooth connection, and

perform pairing with the new device.

Cannot establish a

Bluetooth connection.

This unit is not registered on the connecting

device’s Blue too th connection list.

Perform pairing operations again (☞ page 7).

The unit is in Eco Standby mode. Turn the unit on, then establish a Bluetooth

connection (☞ page 9).

Another Bluetooth device is connected. Terminate current Bluetooth connection, then

establish a Bluetooth connection with that

device again.

The Bluetooth function of the device is

turned off.

Turn on the Bluetooth function of the device.

The pairing information has been deleted. Perform pairing again (☞ page 7).

This unit can be paired with four devices. If

pairing with the fifth device is performed, the

pairing information with the earliest

connection date will be deleted.

Delete any pairing history of TSX-B15 on the

iPhone/iPad/iPod touch, then pair with the

TSX-B15 again (☞ page 8).

No sound is produced or

the sound is interrupted

during playback.

The Bluetooth connection of this unit with

the connecting device is disconnected.

Perform Bluetooth connection operations

again (☞ page 9).

This unit and the connecting device are

too far apart.

Move the connecting device closer to this

unit.

There is a device (microwave oven,

wireless LAN, etc.) that outputs signals in

the 2.4 GHz frequency band nearby.

Move this unit away from the device that is

emitting radio-frequency signals.

The connecting device’s Bluetooth

function is off.

Turn on the Bluetooth function of the

connecting device.

The connecting device is not set to send

Bluetooth audio signals to this unit.

Check that the Bluetooth function of the

connecting device is set properly.

The pairing setting of the connecting

device is not set to this unit.

Set the pairing setting of the connecting

device to this unit.

The connecting device’s volume is set to

the minimum.

Increase the volume level.

The connecting device is connected to

more than two Bluetooth speakers and this

unit (TSX-B15) is not selected as a

playback device.

Select this unit as a playback device for the

connecting device.

USB port charging

Problem Cause Solution

Cannot charge the

connected portable USB

device.

An incompatible USB device is connected

to the unit. Or the USB device is not

connected to this unit properly.

Press to enter standby mode, and reconnect

the USB device to the unit. If it does not

resolve the problem, the USB device is not

chargeable with the unit.

13 En

En

■ PLAYER SECTION

AUX IN

• Input connector

............STEREO L/R: 3.5 mm (1/8 in) STEREO mini Jack

■ AMPLIFIER SECTION

• Driver unit .........................5 cm (2 in) full-range driver × 2

■ Bluetooth SECTION

• Bluetooth version.....................................................Ver. 3.0

• Supported protocols....................................................A2DP

• Supported codecs.......................................................... SBC

• Wireless output.........................................B luetooth Class 2

• Maximum communication distance

...................................... 10 m (33 ft) (without obstructions)

• Supported contents protection.................. SCMS-T method

■ TUNER SECTION

• Tuning range (FM) .................................87.5 to 108.0 MHz

■ CHARGING CONNECTOR SECTION

• Connector type ................................................. USB type A

• Output rating............................................................5 V/1 A

■ GENERAL

• Power Supply............................ AC 100 to 240 V 50/60 Hz

• Power consumption .....................................................11 W

• Standby consumption

(Clock displayed, Bluetooth ready for connection) ....1.0 W

• Eco Standby consumption ..........................................0.2 W

• Time of power management (Auto Standby)

................................................ No sound: about 20 minutes

.................................................No operation: about 8 hours

• Weight......................................................... 0.9 kg (2.0 lbs.)

• Dimensions

Specifications are subject to change without notice.

Bluetooth

• Bluetooth is a technology for wireless communication

between devices within an area of about 10 meters (33 ft)

employing the 2.4 GHz frequency band, a band which can

be used without a license.

• Bluetooth is a registered trademark of the Bluetooth SIG

and is used by Yamaha in accordance with a license

agreement.

Handling Bluetooth communications

• The 2.4 GHz band used by Bluetooth compatible devices

is a radio band shared by many types of equipment. While

Bluetooth compatible devices use a technology

minimizing the influence of other components using the

same radio band, such influence may reduce the speed or

distance of communications and in some cases interrupt

communications.

• The speed of signal transfer and the distance at which

communication is possible differs according to the

distance between the communicating devices, the

presence of obstacles, radio wave conditions and the type

of equipment.

• Yamaha does not guarantee all wireless connections

between this unit and devices compatible with Bluetooth

function.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

SPECIFICATIONS

180 mm (7-1/8 in)

200 mm (7-7/8 in)

100 mm

(3-7/8 in)

iPad, iPhone, and iPod touch are trademarks of Apple

Inc., registered in the U.S. and other countries.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth

terminal of the three pin plug.

Note

i Fr

1 Pour utiliser l’appareil au mieux de ses possibilités,

lisez attentivement ce mode d’emploi. Conservez-le

soigneusement pour référence.

2 Installez cet appareil dans un endroit frais, bien aéré,

sec et propre - à l’abri de la lumière du soleil, des

sources de chaleur, des vibrations, des poussières, de

l’humidité et du froid. Pour une aération correcte,

tenez compte des distances minimales suivantes.

Au-dessus : 15 cm

À l’arrière : 10 cm

Sur les côtés : 10 cm

3 Placez l’appareil loin des équipements, moteurs et

transformateurs électriques, pour éviter les

ronflements parasites.

4 N’exposez pas l’appareil à des variations brutales de

température, ne le placez pas dans un environnement

très humide (par exemple dans une pièce contenant

un humidificateur) car cela peut entraîner la

condensation d’humidité à l’intérieur de l’appareil

qui elle-même peut être responsable de décharge

électrique, d’incendie, de dommage à l’appareil ou de

blessure corporelle.

5 Evitez d’installer l’appareil dans un endroit où des

objets peuvent tomber, ainsi que là où l’appareil

pourrait être exposé à des éclaboussures ou des gouttes

d’eau. Sur le dessus de l’appareil, ne placez pas :

– d’autres appareils qui peuvent endommager la

surface de l’appareil ou provoquer sa décoloration.

– des objets se consumant (par exemple, une

bougie) qui peuvent être responsables d’incendie,

de dommage à l’appareil ou de blessure

corporelle.

– des récipients contenant des liquides qui peuvent

être à l’origine de décharge électrique ou de

dommage à l’appareil.

6 Ne couvrez pas l’appareil d’un journal, d’une nappe,

d’un rideau, etc. car cela empêcherait l’évacuation de

la chaleur. Toute augmentation de la température

intérieure de l’appareil peut être responsable

d’incendie, de dommage à l’appareil ou de blessure

corporelle.

7 Ne branchez pas la fiche du câble d’alimentation de

l’appareil sur une prise secteur aussi longtemps que

tous les raccordements n’ont pas été effectués.

8 Ne pas faire fonctionner l’appareil à l’envers. Il

risquerait de chauffer et d’être endommagé.

9 N’exercez aucune force excessive sur les

commutateurs, les boutons et les cordons.

10 Pour débrancher la fiche du câble d’alimentation au

niveau de la prise secteur, saisissez la fiche et ne tirez

pas sur le cordon.

11 Ne nettoyez pas l’appareil au moyen d’un solvant

chimique, ce qui pourrait endommager la finition.

Utilisez un chiffon sec et propre.

12 N’alimentez l’appareil qu’à partir de la tension

prescrite. Alimenter l’appareil sous une tension plus

élevée est dangereux et peut être responsable

d’incendie, de dommage à l’appareil ou de blessure

corporelle. Yamaha ne saurait être tenue responsable

des dommages résultant de l’alimentation de

l’appareil sous une tension autre que celle prescrite.

13 Pour empêcher tout dommage causé par les éclairs,

déconnectez la câble d’alimentation et toute antenne

extérieure de la prise murale pendant un orage.

14 Ne tentez pas de modifier ni de réparer l’appareil.

Consultez le service Yamaha compétent pour toute

réparation qui serait requise. Le coffret de l’appareil

ne doit jamais être ouvert, quelle que soit la raison.

15 Si vous envisagez de ne pas vous servir de l’appareil

pendant une longue période (par exemple, pendant

les vacances), débranchez la fiche du câble

d’alimentation au niveau de la prise secteur.

16 Lisez la section intitulée « GUIDE DE

DÉPANNAGE » où figurent une liste d’erreurs de

manipulation communes avant de conclure que

l’appareil présente une anomalie de fonctionnement.

17 Avant de déplacer l’appareil, appuyez sur pour

éteindre le système puis débranchez la fiche du câble

d’alimentation au niveau de la prise secteur.

18 La condensation se forme lorsque la température

ambiante change brusquement. En ce cas, débranchez

la fiche du câble d’alimentation et laissez l’appareil

reposer.

19 La température de l’appareil peut augmenter en

raison d’une utilisation prolongée. En ce cas, coupez

l’alimentation de l’appareil et laissez-le au repos pour

qu’il refroidisse.

20 Installez cet appareil à proximité de la prise secteur et

à un emplacement où la fiche du câble d’alimentation

est facilement accessible.

21 Utilisez l’adaptateur secteur fourni avec cet appareil.

L’emploi de tout autre adaptateur secteur peut causer

un incendie ou endommager l’appareil.

ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER

L’APPAREIL.

Cet appareil n’est pas déconnecté du secteur tant qu’il

reste branché à la prise de courant, même si l’appareil en

soi est éteint par la touche . Dans cet état, l’appareil

consomme une très faible quantité de courant.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET

APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

• Les haut-parleurs de cet appareil utilisent des aimants. Ne

placez pas d’objets sensibles au magnétisme comme un

téléviseur à écran cathodique, une horloge, des cartes de

crédit, des disquettes etc. au-dessus ou près de cet appareil.

• Il y a un risque possible de création d’interférences,

visibles sur les images en couleurs si cet appareil est

placé à côté d’un téléviseur à tube cathodique (tube de

Braun). Dans ce cas, éloigner l’unité du téléviseur.

Ne pas utiliser cet appareil à moins de 22 cm de personnes

ayant un stimulateur cardiaque ou un défibrillateur.

Les ondes radio peuvent avoir une incidence sur les

équipements électroniques médicaux.

N’utilisez pas cet appareil à proximité d’équipements

médicaux ou à l’intérieur d’institutions médicales.

1 Fr

Fr

PREPARATION

NOM ET FONCTION DES PIÈCES......................................................................................................... 2

FONCTIONS DE BASE.............................................................................................................................. 4

ÉCOUTE DES STATIONS FM ................................................................................................................. 6

ÉCOUTE DE MUSIQUE AVEC VOTRE DISPOSITIF Bluetooth ....................................................... 7

ÉCOUTE DE SOURCES EXTERNES.................................................................................................... 10

CHARGE AVEC LE PORT USB ............................................................................................................ 10

GUIDE DE DÉPANNAGE ....................................................................................................................... 11

CARACTÉRISTIQUES TECHNIQUES ................................................................................................ 13

■ Caractéristiques

– Lecture de dispositifs Bluetooth, de la radio FM et de dispositifs externes avec un connecteur AUX.

– Réglage de l’alarme avec une radio FM.

– Alimentation de smartphones, tablettes, etc. via le port USB du panneau arrière.

– Son riche grâce à un haut-parleur personnalisé large bande de 5 cm et un DSP (Processeur de signal

numérique) fabriqué par Yamaha.

– Aigus améliorés et médiums/graves épais, même lors de la lecture d’une source audio compressée,

comme un MP3, etc. (Music Enhancer).

• indique les précautions d’utilisation de l’appareil et ses limitations fonctionnelles.

• donne des explications supplémentaires pour une meilleure utilisation.

■ Accessoires fournis

Information concernant la Collecte et le Traitement des déchets

d’équipements électriques et électroniques

Le symbole sur les produits, l’emballage et/ou les documents joints signifie que les produits électriques ou

électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels.

Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et

électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la

réglementation nationale et aux Directives 2002/96/EC.

En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous

contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la

santé humaine qui pourraient advenir lors d’un traitement inapproprié des déchets.

Pour plus d’informations à propos de la collecte et du recyclage des déchets d’équipements électriques et

électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de

vente où vous avez acheté les produits.

[Information sur le traitement dans d’autres pays en dehors de l’Union Européenne]

Ce symbole est seulement valables dans l’Union Européenne. Si vous souhaitez vous débarrasser de

déchets d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre

fournisseur et demander la méthode de traitement appropriée.

Remarque

y

Adaptateur secteur Antenne FM

12 V CC, 1,5 A,

numéro de modèle :

MU18-D120150-C5

TABLE DES MATIÈRES

2 Fr

■ Panneau supérieur

NOM ET FONCTION DES PIÈCES

G Afficheur

H Indicateurs

(alarme) :

s’allume lorsque la fonction

d’alarme est activée

(

☞

page 4).

RADIO : s’allume lorsque la radio est

sélectionnée comme source

d’entrée (☞ page 6).

AUX :

s’allume lorsque

AUX

est sélectionné

comme source d’entrée (

☞

page 10).

(Bluetooth):

s’allume lorsque ( )

Bluetooth est sélectionné

comme source d’entrée

ou pendant l’appariement/

la connexion Bluetooth

(

☞

page 7, 9).

J

Appuyez sur cette touche pour mettre le système sous

tension ou entrer en mode veille.

Mode veille éco

• Cela peut réduire la consommation d’électricité. Appuyez et

maintenez enfoncé pendant plus de 3 secondes pour mettre

le système en d’économie d’énergie. Tous les indicateurs et

l’afficheur s’éteignent, et l’utilisation de Bluetooth, la lecture

audio, l’entrée via les touches (à l’exception de ) sont

désactivées. Pour annuler le mode veille éco, appuyez sur .

• Même en mode veille ou en mode veille éco, la fonction

d’alarme est disponible.

Mise en veille automatique (☞ page 5)

• Cet appareil possède une fonction qui active automatiquement

le mode veille quand aucun signal audio n’est reçu par un

périphérique connecté ou lorsque le périphérique connecté est

en cours de lecture à faible volume pendant une certaine durée

(environ 20 minutes).

y Fonction de gradateur de

lumière

Appuyez sur CLOCK plusieurs fois de suite

pour régler la luminosité de l’afficheur et des

indicateurs.

3 (le plus lumineux) 2 1 (le plus sombre)

I Grille (☞ page 3)

A VOLUME

Règle le volume. Lorsque vous

réglez le volume, le niveau de

volume apparaît sur l’afficheur

pendant quelques instants.

B CLOCK

Règle l’horloge (☞ page 4).

C ALARM

Règle l’alarme (☞ page 4).

D TUNING

Règle l’heure ou la fréquence

radio (☞ page 4, 6).

E PRESET

Mémorise jusqu’à cinq stations

radio FM favorites (☞ page 6).

F SOURCE (PAIRING)

Sélectionne une source d’entrée

parmi (Bluetooth), AUX ou

RADIO.

NOM ET FONCTION DES PIÈCES

3 Fr

Fr

■ Panneau arrière

Une grille est fixée à ce produit pour protéger les haut-parleurs.

• Comme le tissu de la grille est fabriqué à partir d’un matériau souple, il est susceptible de s’abîmer plus facilement, c’est

pourquoi il faut éviter de le rayer avec un objet pointu.

• Ne surchargez pas le tissu de la grille. S’il est surchargé, il va se tordre et s’endommager. Cela risque d’endommager les

haut-parleurs. Manipulez le tissu de la grille avec précaution.

Raccordement de l’antenne FM

A Raccordez l’antenne fournie à

l’appareil.

B Accrochez l’antenne à l’endroit où la

réception est la meilleure.

• Assurez-vous de déployer l’antenne comme illustré.

• Si la réception FM est mauvaise, changez la hauteur, le

sens ou l’emplacement de l’appareil.

Si vous écoutez une station radio FM pendant le chargement

du périphérique USB, des interférences peuvent entraver la

réception radio. Dans ce cas, déconnectez le câble USB de

l’appareil.

Attention

K CHARGING

Alimente en 5 V/1 A un

dispositif portable,

comme un smartphone,

lorsque celui-ci est

branché avec un câble

USB (☞ page 10).

L 12 V

Branchez

l’adaptateur

secteur

fourni.

M AUX

Branchez les dispositifs externes

avec des câbles à mini fiche

stéréo de ø3,5 mm (☞ page 10).

N FM ANT

Borne d’antenne FM

Vers la prise murale

A

B

Remarque

Attention

4 Fr

OPERATION

Cet appareil peut lire la radio et faire retentir des bips sonores à l’heure que vous avez définie.

■ Réglage de l’heure et du son

FONCTIONS DE BASE

Réglage de l’horloge

A Appuyez et maintenez CLOCK enfoncé

pendant plus de 2 secondes.

L’afficheur clignote.

B Réglez l’heure avec TUNING.

y

Si vous appuyez et maintenez TUNING enfoncé, les

numéros avancent rapidement.

C Appuyez sur CLOCK.

Pour annuler le mode de réglage de l’horloge,

appuyez sur .

y

Si vous appuyez sur PRESET à l’étape B, vous

pouvez sélectionner la méthode d’affichage de

l’heure (12 heures/24 heures).

Les paramètres de l’heure se perdent environ une semaine

après avoir débranché l’appareil.

Réglage de l’alarme

A Appuyez et maintenez ALARM enfoncé

pendant plus de 2 secondes.

L’indicateur d’alarme ( ), l’indicateur

RADIO et l’afficheur clignotent.

B

Réglez l’heure d’alarme avec

TUNING

.

C Réglez le volume de l’alarme avec

VOLUME.

Le niveau du volume s’affiche.

D Appuyez sur ALARM.

L’alarme est réglée et l’indicateur d’alarme

( ) s’allume.

y

• Le type d’alarme de cet appareil comporte

uniquement la radio et des bips sonores.

• La radio s’allume 3 minutes avant l’heure d’alarme

et les bips sonores commencent à l’heure d’alarme.

Si vous appuyez sur ALARM pour terminer le réglage de

l’alarme sans modifier l’heure et le volume de l’alarme, le

mode de réglage d’alarme est annulé et l’alarme n’est pas

activée.

A

,

C

B

Remarque

A

,

D

C

B

Indicateur RADIO

Indicateur

d’alarme

()

Remarque

Sivu latautuu ...

Yamaha TSX-B15 Omistajan opas

Yamaha TSX-B15 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat