Yamaha RX-V1065 Omistajan opas

Printed in Malaysia WQ95000

RX-V1065

AV R e c e i ve r

OWNER’S MANUAL

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

F

00_RX-V1065_F_cv.fm Page 1 Monday, May 11, 2009 2:52 PM

Black process 45.0° 240.0 LPI

Caution-i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press KMAIN ZONE ON/OFF to

set this unit to the standby mode, and disconnect the AC

power plug from the wall outlet in the main room.

19

VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

..... AC 110/120/220/230-240 V, 50/60 Hz (General model)

.........................AC 220/230-240 V, 50/60 Hz (Asia model)

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by KMAIN ZONE ON/OFF.

In this state, this unit is designed to consume a very

small quantity of power.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

1 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

About this manual................................................... 3

Supplied accessories................................................ 3

Part names and functions....................................... 4

Front panel ................................................................. 4

Rear panel .................................................................. 5

Front panel display..................................................... 6

Remote control........................................................... 7

Quick start guide..................................................... 8

L

Preparing remote control .......................................9

Installing batteries in the remote control ................... 9

Using the remote control............................................ 9

Connections ...........................................................10

Placing speakers....................................................... 10

Connecting speakers ................................................ 11

Information on jacks and cable plugs ...................... 13

Connecting a TV monitor or projector .................... 14

Connecting other components ................................. 15

Connecting a Yamaha iPod universal dock or

Bluetooth™ wireless audio receiver.................... 17

Connecting a USB storage device ........................... 18

Using the VIDEO AUX jacks.................................. 18

Connecting the FM and AM antennas ..................... 18

Connecting the power cable..................................... 19

Turning this unit on and off ..................................... 19

Optimizing the speaker setting for your

listening room (YPAO) .....................................20

Using Auto Setup..................................................... 20

When an error message is displayed during

measurement ........................................................ 22

When a warning message is displayed after

measurement ........................................................ 22

Playback................................................................. 23

Basic procedure........................................................ 23

Using the SCENE function ...................................... 23

Selecting a source on the GUI screen ...................... 24

Muting audio output................................................. 24

Adjusting high/low frequency sounds

(tone control) ....................................................... 24

Enjoying pure hi-fi sound ........................................ 24

Using your headphones............................................ 25

Displaying input signal information ........................ 25

Changing information on the front panel display .... 25

Enjoying the sound field programs ..................... 26

Selecting sound field programs................................ 26

Enjoying unprocessed input sources

(Straight decode mode)........................................ 29

Enjoying sound field programs without surround

speakers (Virtual CINEMA DSP) ....................... 29

Enjoy sound field programs with headphones

(SILENT CINEMA™) ........................................ 29

Using CINEMA DSP 3D mode ............................... 29

FM/AM tuning ...................................................... 30

Tuning in to the desired FM/AM station

(Frequency tuning) .............................................. 30

Registering FM/AM stations and tuning in

(Preset tuning)...................................................... 30

Radio Data System tuning.................................... 32

Displaying the Radio Data System information ...... 32

Selecting the Radio Data System program type

(PTY Seek) .......................................................... 32

Using the enhanced other networks (EON) data

service.................................................................. 33

Using iPod™ .......................................................... 34

Controlling iPod™................................................... 34

Using Bluetooth™ components ........................... 36

Pairing the Bluetooth™ wireless audio receiver

and your Bluetooth component............................ 36

Playback of the Bluetooth™ component ................. 36

Using USB storage devices................................... 37

Playback of the USB storage device........................ 37

Other functions ..................................................... 38

Using the sleep timer ............................................... 38

Using the HDMI™ control function........................ 38

Setting the option menu for each input source

(Option menu)................................................... 39

Option menu items................................................... 39

Selecting a video signal to be output during an

audio reproduction............................................... 41

Editing surround decoders/

sound field programs........................................ 42

Setting sound field parameters................................. 42

Sound field parameters ............................................ 42

Operating various settings for this unit

(Setup menu) ..................................................... 46

Basic operation of the Setup menu .......................... 47

Speaker Setup .......................................................... 47

Sound Setup ............................................................. 49

Function Setup ......................................................... 50

DSP Parameter ......................................................... 52

Memory Guard......................................................... 52

Using multi-zone configuration ........................... 53

Connecting Zone2.................................................... 53

Controlling Zone2.................................................... 54

Controlling other components with the remote

control................................................................ 55

Setting remote control codes.................................... 55

Resetting all remote control codes........................... 55

Programming from other remote controls ............... 56

Advanced setup..................................................... 57

Troubleshooting.................................................... 59

Glossary ................................................................. 68

Sound field program information ....................... 70

Information on HDMI™...................................... 71

Specifications......................................................... 72

Index ...................................................................... 73

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

APPENDIX

Information about software.................................... i

List of remote control codes................................... ii

2 En

INTRODUCTION

■ Built-in 7-channel power amplifier

• Minimum RMS Output Power (20 Hz to 20 kHz, 0.08%

THD, 8 Ω)

• FRONT L/R: 105 W + 105 W

• CENTER: 105 W

• SURROUND L/R: 105 W + 105 W

• SURROUND BACK L/R: 105 W + 105 W

■ Speaker/Preout outputs

• Speaker terminals (7-channel), extra speaker terminals

(2-channel for presence or Zone2), preout jacks (7.1-

channel)

■ Input/Output terminals

Input terminals

• HDMI input x 4

• Audio/Visual input

[Audio] Digital input (coaxial) x 2, digital input

(optical) x 2, analog input x 2

[Video] Component video x 2, S-video x 1, Video x 4

• Audio input (analog) x 2

• Phono input (analog) x 1

• Multi-channel audio input (7.1-channel)

• V-AUX input

[Audio] Analog x 1

[Video] Video x 1

• DOCK terminal to connect a Yamaha iPod universal

dock (such as YDS-11, sold separately) or Bluetooth

wireless audio receiver (such as YBA-10, sold

separately)

• USB port to connect a USB storage device

Output terminals

• Monitor output

[Audio/Video] HDMI x 1

[Video] Component video x 1, Video x 1

• Audio/Visual output

[Audio] Analog x 1

[Video] Video x 1

• Audio output

Analog x 1

• Zone2 output

Analog x 1

Other terminals

Remote input x 1, Remote output x 1

Trigger output x 1

■ Proprietary Yamaha technology for the

creation of sound fields

• CINEMA DSP 3D

• Compressed Music Enhancer mode

• Virtual CINEMA DSP

• SILENT CINEMA

■ Digital audio decoders

• Dolby TrueHD, Dolby Digital Plus decoder

• DTS-HD Master Audio, DTS-HD High Resolution

Audio, DTS Express

• Dolby Digital/Dolby Digital EX decoder

• DTS, DTS 96/24 decoder, DTS-ES Matrix 6.1, DTS-ES

Discrete 6.1

• Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic

IIx decoder

• DSD decoder

•

DTS NEO:6 decoder

■ Sophisticated FM/AM tuner

• 40-station random and direct preset tuning

• Automatic preset tuning

• Radio Data System tuning

■

HDMI™ (High-Definition Multimedia Interface)

• HDMI interface for standard, enhanced or high-

definition video as well as multi-channel digital audio.

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission

capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

• Analog to analog and HDMI digital video up-

conversion (video ↔ component video → HDMI)

capability for monitor out

•

Analog video input up-scaling for HDMI digital video

output 480i(576i) or 480p(576p)

→

720p, 1080i or 1080p

• HDMI control function supported

■ Automatic speaker setup features

• “YPAO” (Yamaha Parametric Room Acoustic

Optimizer) for automatically optimizing speaker

outputs suitable for listening environments.

■ Other features

• 192-kHz/24-bit D/A converter

• GUI (graphic user interface) menus to optimize this unit

to suit individual audiovisual system

• iPod and USB file browsing and album art display

capability

• Pure Direct mode for pure hi-fi sound for all sources

• Adaptive dynamic range controlling capability

• SCENE function for changing input sources and sound

field programs with one key

• Bi-amplification connection capability

• Sleep timer

• Multi-zone function

Features

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &

other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and DTS-

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other

countries.

Bluetooth

™

Bluetooth is a registered trademark of Bluetooth SIG and is used by

Yamaha in accordance with a license agreement.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

Check that you received all of the following parts.

• Remote control (page 7)

• Batteries (2) (AAA, R03, UM-4) (page 9)

• Optimizer microphone (page 20)

• AM loop antenna (page 18)

• Indoor FM antenna (page 18)

About this manual

• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between

the front panel and the remote control, the key name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of

differences between the manual and product, the product has priority.

• For better viewing, we increase the size of characters used in example screen images in this manual. Therefore the size ratio of characters to other

objects (such as icons) may be different from that of the actual display image.

• “KMAIN ZONE ON/OFF” or “dHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the

attached sheet or “Part names and functions” (page 4).for the information about each position of the parts.

• ☞ indicates the page describing the related information.

• y indicates a tip for your operation.

Supplied accessories

4 En

A ZONE2 ON/OFF

Switches the zone function on and off (page 54).

B HDMI THROUGH

Lights up in the following cases while this unit is on standby.

• when the HDMI control function is on

• when the HDMI signal standby-through function is currently

working

C ZONE2 CONTROL

Enables operation of a receiver set in Zone2, including input

source switching, volume control and tuner operation, with the

main amplifier or remote control after this key is pressed

(page 54).

D INFO

Changes information (input, DSP program, audio decoder, etc)

displayed on the front panel display (page 25).

E MEMORY

Registers FM/AM stations as preset stations (page 31).

F PRESET l / h

Selects an FM/AM preset station (page 31).

G FM/AM

Change the tuner bands between FM and AM.

H TUNING l / h

Changes FM/AM frequencies.

I Front panel display

Displays information on this unit (page 6).

J VOLUME control

Controls the volume of this unit (page 23).

K MAIN ZONE ON/OFF

Turns this unit on and off (page 19).

L PHONES jack

For plugging headphones (page 25).

M TONE CONTROL

Adjusts high-frequency/low-frequency output of speakers

(page 24).

N PROGRAM selector

Changes sound field programs (page 26).

O STRAIGHT

Toggles between the selected sound field program and straight

decode mode (page 29).

P SCENE

Switches between linked sets of input sources and sound field

programs (page 23).

Q PURE DIRECT

Changes mode to Pure Direct mode (page 24). This key lights up

when Pure Direct mode is on.

R INPUT selector

Selects an input source (page 23).

S OPTIMIZER MIC jack

For connecting the supplied optimizer microphone and adjusting

output characteristics of speakers (page 20).

T VIDEO (VIDEO AUX) jack

For connecting the video output cable of a camcorder or game

console (page 18).

U AUDIO L/R (VIDEO AUX) jack

For connecting the audio output cable of a camcorder or game

console (page 18).

V USB port

For connecting a USB memory device or USB portable audio

player (page 18)

Part names and functions

Front panel

MAIN

ZONE

ON/OFF

PHONES

SILENT

CINEMA

TONE

CONTROL

PROGRAM

STRAIGHT

PURE DIRECT

INPUT

OPTIMIZER

MIC

VIDEO

AUDIO

THROUGH

VIDEO

AUX

USB

VOLUME

HDMI

EFFECT

BD/DVD

TV

CD

RADIO

SCENE

ZONE2

ON/OFF

INFO

MEMORY

ZONE2

CONTROL

PRESET

l

h

l

h

FM AM TUNING

KNQMO R

ABC D E F G H I J

SULPTV

5 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a DOCK terminal

For connecting an optional Yamaha iPod universal dock (YDS-

11) or Bluetooth wireless audio receiver (YBA-10) (page 17).

b PHONO jacks

For connecting a turntable (page 15).

c ANTENNA terminals

For connecting supplied FM and AM antennas (page 18).

MONITOR OUT jacks

Outputs visual signals from this unit to a video monitor, such as

a TV (page 14).

REMOTE IN/OUT jacks

For connecting an external component that supports the remote

control function (page 17).

TRIGGER OUT jack

For connecting an external terminal with a trigger input terminal

to operate it linked with operation of this unit. For example,

when an electric screen that supports a trigger input is

connected, it opens and closes linked with operation of an input

source selected in this unit.

d HDMI OUT/HDMI 1-4 jacks

For connecting an HDMI-compatible video monitor or external

components for HDMI inputs 1-4 (pages 14 and 15).

e SPEAKERS terminals

For connecting front, center, surround and surround back

speakers (page 11). Connect the presence speakers (page 11) or

the speakers for Zone2 (page 53) to EXTRA SP terminals.

f Power cable

Connect this cable to an AC wall outlet (page 19).

g AV 1-6 jacks

For connecting external components for audio/visual inputs 1-6

(page 15).

h AV OUT jacks

Outputs audio/visual signals from a selected analog input source

to an external component (page 15).

i AUDIO 1/2 jacks

For connecting external components for audio inputs 1-2

(page 15).

j MULTI CH INPUT jacks

For connecting a player that supports a multi-channel output

(page 16).

k AUDIO OUT jacks

Outputs audio signals from a selected analog input source to an

external component (page 15).

l ZONE2 OUT jacks

Outputs sound of this unit to an external amplifier set in a

different zone (page 53).

m PRE OUT jacks

Outputs multi-channel signals from up to 7.1 channels to an

external amplifier (page 17).

Rear panel

DOCK

PHONO ANTENNA

COMPONENT

VIDEO

PR

PB

Y

OPTICAL

(

TV

)

A

V

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

ZONE2

OUT

FRONT

SURROUND

SUR. BACK SUBWOOFER

PRE OUT

CENTER

SINGLE

VIDEO

GND

HDMI OUT

UNBAL.

FM

GND

S VIDEO

AM

HDMI 1

(

BD/DVD

)

HDMI 2

HDMI 3

HDMI 4

VIDEO

IN

OUT

MONITOR OUT

SPEAKERS

TRIGGER OUT

12V

0.1A MAX.

FRONT

CENTER

SINGLE

SURROUND

SURROUND BACK/

BI-AMP

EXTRA SP

ZONE2/PRESENCE

12

CENTER

PR

PB

Y

REMOTE

COMPONENT

VIDEO

a

ghijkl m

cd efb

6 En

Part names and functions

a HDMI indicator

Lights up during normal communication when HDMI is

selected as an input source.

b CINEMA DSP indicator

Lights up when a sound field program that uses CINEMA DSP

is selected.

c CINEMA DSP 3D indicator

Lights up when CINEMA DSP 3D is activated.

d Tuner indicator

Lights up during receiving radio broadcast signals from an FM/

AM station (page 30).

e ZONE2 indicator

Lights up when Zone2 is turned on.

f SLEEP indicator

Lights up when the sleep timer is activated (page 38).

g MUTE indicator

Flashes when audio is muted.

h VOLUME indicator

Displays volume levels.

i Cursor indicators

Light up if corresponding cursors on the remote control are

available for operations.

j Multi information display

Displays menu items and settings for the current operation.

k Speaker indicators

Indicate speaker terminals from which signals are currently

output.

Front panel display

STEREO

SLEEP

VOL.

TUNED

PL PR

SW

C

LR

SL SR

SBL SB SBR

MUTE

3

ZONE

2

acbfhedg

ij ki

SW

C

LR

SL SR

SBL SB SBR

PL PR

Subwoofer

Front L

Surround L

Surround back L

Center

Front R

Surround R

Surround back R

Surround back

Presence L Presence R

7 En

Part names and functions

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

a Remote control signal transmitter

Transmits infrared signals.

b MAIN/ZONE2

Switches amplifiers (Main or Zone2) to be operated by the

remote control (page 54).

c SOURCE POWER

Switches an external component on and off.

d Input selection keys

e Tuner keys

f INFO

Changes the information shown on the front panel display

(page 25).

g Sound selection keys

Selects sound field programs (page 26).

h SCENE

Switches between linked sets of input sources and sound field

programs (page 23).

i ON SCREEN

Displays the GUI screen (page 24).

k External component operation keys

Operate recording, playback etc. of external components

(page 55).

l Numeric keys

Enter numbers.

m TV control keys

Enables operations of a TV or a projector (page 55).

n TRANSMIT

Lights up when a signal is output from the remote control.

o CODE SET

Sets remote control codes for external component operations

(page 55).

p POWER

Switches this unit on and standby (page 19).

q SLEEP

Switches the sleep timer operations (page 38).

r OPTION

Displays the Option menu (page 39).

s VOLUME +/–

Adjust the volume of this unit (page 23).

t DISPLAY

Displays the play information on the video monitor.

When an iPod is connected: Changes the operation mode of the

iPod connected to the Yamaha iPod universal dock (page 34).

u MUTE

Turns the mute function on and off (page 24).

Remote control

MAIN

POWER

1234

1256

1234

7856

90

10

1234

POWER

SOURCE

V-AU X

PHONO

USB DOCK

MULTI

TUNER

FM

MOVIE

BD

DVD

TOP

MENU

MUSIC

SCENE

TV

CD

OPTIONON SCREEN

RETURN

REC

ENT

POWER

TV

TV VOL

INPUT

MUTE

TV CH

ENTER

VOLUME

DISPLAY

MUTE

MENU

RADIO

STEREO

ENHANCER SUR. DECODE

PURE DIRECT

STRAIGHT

INFO

MEMORY

AM

PRESET

TUNING

SLEEP

HDMI

AV

AUDIO

ZONE2

TRANSMIT

CODE SET

a

c

p

d

e

g

h

i

r

s

t

u

k

l

m

b

o

n

j

f

q

HDMI 1-4

Selects HDMI inputs 1 through 4.

AV 1-6

Selects AV inputs 1 through 6.

AUDIO 1/2

Selects AUDIO inputs 1 and 2.

V-AUX

Selects a signal input from the VIDEO AUX jacks.

PHONO

Selects a signal input from the PHONO jacks.

USB

Selects a USB device connected to the USB port.

DOCK

Selects a Yamaha iPod universal dock/Bluetooth

wireless audio receiver connected to the DOCK

terminal.

TUNER

Selects the FM/AM tuner.

MULTI

Selects a signal input from the MULTI CH

INPUT jacks.

FM/AM

Switches a band between FM and AM.

MEMORY

Presets radio stations.

PRESET k / n

Selects a preset station.

TUNING k / n

Changes FM/AM frequencies.

j Cursors k / n / l / h

Select menu items or change

settings.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen or

ends the menu display.

8 En

When you use this product for the first time, perform setup following the steps below. See the related pages for details on

operations and settings.

Prepare speakers, DVD player, cables, and other items

necessary for setup.

For example, prepare the following items for setting up a

7.1-channel sound system.

y

• Prepare two magnetically shielded speakers (for front). The priority of

the requirement of other speakers is as follows:

1 Two surround speakers

2 One center speaker

3 One (or two) surround back speaker(s)

• If your video monitor is a CRT, we recommend that you use magnetically

shielded speakers.

• Video and audio cables are unnecessary if you use HDMI cables.

Place your speakers in the room and connect them to this

unit.

y

• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)

that automatically optimizes this unit based on room acoustic

characteristics (audio characteristics of the speakers, speaker positions,

and room acoustics, etc.).

You can enjoy good balanced sound without special knowledge by using

the YPAO technology (☞P. 20).

Connect your TV, DVD player, or other components.

Connect the power cable and turn on this unit.

Select the component connected in step 3 as an input

source and start playback.

y

• This unit supports the SCENE function (page 23) that changes the input

source and sound field program at one time. Four scenes are preset for

different purposes for Blu-ray disc, DVD and CD, and you can select

from a scene from those just by pressing a remote control key.

Quick start guide

Step 1: Prepare items for setup

Requirements qty.

Speakers Front speaker 2

Center speaker 1

Surround speaker 2

Surround back

speaker

2

Active subwoofer 1

Speaker cable 7

Subwoofer cable 1

Reproduction component such as DVD player 1

Video monitor such as TV 1

Video cable or HDMI cable 2

Audio cable 2

Front right speaker

Subwoofer

Surround left speaker

Surround right speaker

Front left

speaker

Video monitor

Center

speaker

Components

(such as DVD player)

Surround Back

right speaker

Surround Back

left speaker

Step 2: Set up your speakers

• Placing speakers ☞P. 1 0

• Connecting speakers ☞P. 1 1

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 1 4

• Connecting other components ☞P. 1 5

• Connecting a multi-format player or an

external decoder ☞P. 1 6

• Connecting an external amplifier ☞P. 1 7

• Connecting a USB storage device ☞P. 1 8

• Connecting a Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞P. 1 7

• Connecting the FM and AM antennas ☞P. 1 8

Step 4: Turn on the power

• Connecting the power cable ☞P. 1 9

• Turning this unit on and off ☞P. 1 9

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 2 3

• Selecting sound field programs ☞P. 2 6

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

PREPARATION

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows

– the transmit indicator does not flash or is dim

• Do not use old batteries together with new ones.

This may shorten the life of the new batteries or cause old batteries

to leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may be

different even though they look the same.

• If you find leaking batteries, discard the batteries immediately,

taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Dispose of the old batteries correctly in accordance with your local

regulations.

• If the remote control is without batteries for more than 2 minutes,

or if exhausted batteries remain in the remote control, the contents

of the memory may be cleared. In such a case, install new batteries

and set the remote control code.

The remote control transmits a directional infrared ray. Be

sure to aim the remote control directly at the remote

control sensor on this unit during operation.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

y

• You can operate external components with this remote control by setting

the remote control code (page 55).

Preparing remote control

Installing batteries in the remote

control

1

3

2

Using the remote control

30 30

Remote control sensor window

within 6 m (20 ft)

10 En

This unit supports up to 7.1-channel surround. We recommended the following speaker layout in order to obtain the

optimum surround effect.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

■ Front left and right speakers (FL and FR)

The front speakers are used for the front channel sounds

(stereo sound) and effect sounds. Place these speakers at

an equal distance from the ideal listening position. When

using a screen, the appropriate top positions of the

speakers are about 1/4 of the screen from the bottom.

■ Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). Place it halfway between the left and

right speakers. When using a TV, place the speaker just

above or just under the center of the TV with the front

surfaces of the TV and the speaker aligned. When using a

screen, place it just under the center of the screen.

■ Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds. Place them at the rear left and rear right facing the

listening position. To obtain a natural sound flow in the

5.1-channel speaker layout, place them slightly further

back than in the 7.1-channel speaker layout.

■ Surround back left and right speakers (SBL

and SBR) / Surround back speaker (SB)

The surround back left and right speakers are used for rear

effect sounds. Place them at the rear of the room facing the

listening position at least 30 cm (1 ft) away from each

other, ideally at the same distance as that between the

front left and right speakers.

In the 6.1-channel speaker layout, surround back left and

right channel sound signals are mixed down and output

from the single surround back speaker.

In the 5.1-channel speaker layout, surround back left and

right channel sound signals are output from the surround

left and right speakers.

■ Subwoofer (SW)

The subwoofer speaker is used for bass sounds and low-

frequency effect (LFE) sounds included in Dolby Digital

and DTS signals. Use a subwoofer with a built-in

amplifier, such as the Yamaha Active Servo Processing

Subwoofer System. Place it exterior to the front left and

right speakers facing slightly inward to reduce reflections

from a wall.

Connections

Placing speakers

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

SW

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

SW

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Speaker channels

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

■ Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the

front speakers with extra ambient effects produced by the

sound field programs (page 26). We recommend that you

use the presence speakers especially for the CINEMA

DSP sound field programs. To use the presence speakers,

connect the speakers to EXTRA SP terminals and then set

“Extra Speaker Assignment” to “Presence” (page 48).

Connect your speakers to the respective terminals as follows, according to your speaker layout.

y

• Connect optional presence speakers or Zone2 speakers (page 53) to the EXTRA SP terminals.

• You can connect up to two subwoofers. When two subwoofers are connected, the same sound is output from them.

■ 7.1-channel (with presence speakers)

■ 6.1-channel (with Zone2 speakers)

■ 5.1-channel (with Zone2 speakers)

FR

PRPL

C

FL

0.5 to 1 m (1 to 3 ft)0.5 to 1 m (1 to 3 ft)

1.8 m

(6 ft)

1.8 m

(6 ft)

Connecting speakers

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker L SURROUND

BACK/BI-AMP (L)

g Surround back speaker R SURROUND

BACK/BI-AMP (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Presence speaker L (optional) EXTRA SP (L)

k Presence speaker R (optional) EXTRA SP (R)

SUBWOOFER

SPEAKERS

FRONT

CENTER

SINGLE

SURROUND

SURROUND BACK/

BI-AMP

EXTRA SP

ZONE2/PRESENCE

12

S

UR.BA

CK

SU

BW

OO

FE

R

H

INP

U

T

AUDIO

O

U

T

ZO

NE

2

O

U

T

F

R

O

N

T

S

URR

O

UND

S

UR. BA

CK

P

RE

OU

T

C

ENTER

S

IN

G

LE

H

DMI

3

HDMI

4

T

2

V

MAX.

C

ENTER

E

c

g f

h i

e d

b a

k j

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker SURROUND

BACK/BI-AMP (SINGLE)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Zone2 speaker L (optional) EXTRA SP (L)

k Zone2 speaker R (optional) EXTRA SP (R)

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Zone2 speaker L (optional) EXTRA SP (L)

k Zone2 speaker R (optional) EXTRA SP (R)

12 En

Connections

■ Connecting speaker cables

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist bare wires of the cable

together so that they will not cause a short

circuits.

2 Loosen the knob, insert the twisted bare

wires into the hole and then tighten the knob.

■ Using bi-amplification connections

You can make bi-amplification connections to one speaker

system which supports bi-amplification connection as

shown below. To activate the connections, set “BI-AMP”

to “ON” in the advanced setup menu (page 57).

Note

• You cannot use surround back speakers or extra speakers (presence and

Zone2 speakers) when bi-amplification connections are made.

Caution

• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently

or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit

and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this

unit and the other end to that of your speaker.

• Before connecting the speakers, be sure to disconnect the power cable.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or

speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned

on.

• If images on the monitor (CRT) are distorted, place the speakers away from the video monitor. If it does not work,

use magnetically shielded speakers.

• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in the advanced setup menu before

connecting the speakers (page 57). You can also use 4-ohm speakers as the front speakers when you set “SP IMP.” to

“6ΩMIN”.

Connecting the banana plug (Except Korea,

U.K., Europe, Russia and Asia models)

Tighten the knob and then insert the banana plug into

the end of the terminal.

10 mm (0.4 in)

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Caution

Before making bi-amplification connections, remove

any brackets or cables that connect a woofer with a

tweeter. Refer to the instruction manuals of speakers for

details.

When not making bi-amplification connections, make

sure that the brackets or cables are connected before

connecting the speaker cables.

SURROUND BACK/

BI-AMP

FRONT

Front speakers

Right Left

This unit

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are

connecting.

■ Audio jacks

■ Video jacks

■ Video/audio jacks

y

• We recommend that you use a commercially available 19-pin HDMI

cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect this unit

to other DVI components.

• You can check the potential problem about the HDMI connection

(page 40).

Information on jacks and cable plugs

Jack and cables Description

Analog audio jacks To transmit conventional analog

stereo audio signals. Use stereo pin

cables. Connect red plugs to red

jacks (R) and white plugs to white

jacks (L).

COAXIAL jacks To transmit coaxial digital audio

signals. Use pin cables for digital

audio signals.

OPTICAL jacks To transmit optical digital audio

signals. Use optical fiber cables for

optical digital audio signals.

Jack and cables Description

VIDEO jacks To transmit conventional

composite video signals. Use video

pin cables.

S VIDEO jack To transmit S-video signals that

include luminance (Y) and

Cameroonians (C) components.

Use an S-video cable.

COMPONENT VIDEO

jacks

To transmit component video

signals that include luminance (Y),

chrominance blue (PB) and

chrominance red (PR) components.

Use component video cables.

L

R

(white)

(red)

COAXIAL

C

(orange)

OPTICAL

O

VIDEO

V

(yellow)

S VIDEO

S

PR

PB

Y

COMPONENT

VIDEO

P

B

Y

P

R

(red)

(blue)

(green)

Jack and cables Description

HDMI jacks To transmit digital video and

digital audio signals. Use HDMI

cables.

This unit automatically converts input video signals and

outputs the signals to the HDMI OUT jack and

MONITOR OUT (COMPONENT VIDEO and

VIDEO) jacks (video conversion).

HDMI

VIDEO

COMPONENT

VIDEO

Y

P

B

PR

HDMI

VIDEO

COMPONENT

VIDEO

Y

P

B

PR

S VIDEO

Input Output

Through Converted

14 En

Connections

According to the types of video input jacks available on your video monitor (such as a TV or projector), choose one of

the connection methods as shown below. When you connect video players such as a DVD player to this unit with an

HDMI connection, connect your video monitor to this unit with an HDMI connection.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ To connect an HDMI video monitor

y

• This unit supports the HDMI control function (page 38). If your TV

supports the HDMI control function, you can control this unit with the

remote control of your TV.

■ To connect component video monitor

■ To connect composite video monitor

To output sound of a TV from this unit, make connection

between one of the AV 1-6 jacks of this unit and an audio

output jack of the TV.

If the TV supports an optical digital output, we

recommend that you use the AV 1 jack. Connecting to the

AV 1 jack allows you to switch an input source to the AV 1

jack with a just a single key operation using the SCENE

function (page 23).

Connecting a TV monitor or projector

Jacks on components Jacks on this unit

a HDMI input HDMI OUT

Jacks on components Jacks on this unit

b Component video output MONITOR OUT

(COMPONENT VIDEO)

Jacks on components Jacks on this unit

c Video input (composite) MONITOR OUT (VIDEO)

HDMI OUT

VIDEO

MONITOR OU

T

P

R

P

B

Y

COMPONENT

VIDEO

P

HON

O

ANTENNA

L

O

PTICAL

AV

4

AV

5

AV

6

A

V

O

UT

AU

DI

O1

A

UDI

O

2

FR

O

N

T

S

URR

O

UND

SU

R.B

A

M

ULTI CH INP

U

GND

UNBAL

.

FM

G

ND

S

VIDE

O

AM

HDMI 1

(

BD

/

DVD

)

HDMI 2

H

D

M

IN

O

UT

TRI

GG

ER

OUT

12V

0

.1

A

MAX

.

REMOT

E

HDMI

V

a

c

b

P

B

YP

R

TV, or projector

Outputting TV sounds from this unit

OPTICAL

(

TV

)

AV

1

P

R

P

B

Y

AV 2

CO

AXIA

L

AV

3

(

CD

)

CO

AXIAL

O

PTICAL

AV

4

AV

5

AV

6

AV

O

UT

AU

DI

O1

A

U

D

V

IDE

O

GND

F

M

GND

AM

P

R

P

B

Y

O

Digital output

(optical)

TV

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has input and output terminals for respective input and output sources. You can reproduce sound and movies

from input sources selected with the front panel display or remote control.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ Audio and video player / Set-top box

Connecting other components

Output jacks on the connected external component Input sources/jacks of this unit

External

component

Signal Output jack Input source Input jack

External component

with HDMI output

Audio/Video HDMI output HDMI 1 (BD/DVD) HDMI 1

HDMI 2 HDMI 2

HDMI 3 HDMI 3

HDMI 4 HDMI 4

External component

with component video

output

Audio Optical digital output AV 1 (TV) OPTICAL

Video Component video COMPONENT VIDEO

Audio Coaxial digital output AV 2 COAXIAL

Video Component video output COMPONENT VIDEO

External component

with S-video output

Audio

Video

Analog audio output

S-video output

AV 5 Analog audio

S VIDEO

External component

with composite video

output

Audio Coaxial digital output AV 3 (CD) COAXIAL

Video Composite output VIDEO

Audio Optical digital output AV 4 OPTICAL

Video Composite output VIDEO

Audio Analog audio output AV 5 Analog audio

Video Composite output VIDEO

Audio Analog audio output AV 6 Analog audio

Video Composite output VIDEO

PHONO

COMPONENT

VIDEO

P

R

P

B

Y

OPTICAL

(

TV

)

AV

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

VIDEO

GND

S VIDEO

HDMI 1

(

BD/DVD

)

HDMI 2

HDMI 3

HDMI 4

TRIGGER

OUT

CENTER

DOCK

ANTENNA

Z

O

HDMI OUT

UNBAL

.

FM

GN

D

AM

VIDE

O

IN

O

UT

M

O

NIT

O

R

OUT

TRIGGER OUT

12V

0

.1A MAX.

F

R

O

NT

P

R

P

B

Y

REM

O

TE

CO

MP

O

NENT

V

IDE

O

Audio / video input

(AV 1-6)

Audio / video output (AV OUT)

Audio input (AUDIO 1/2)

HDMI input

(HDMI 1-4)

Audio output

(AUDIO OUT)

Multi channel audio input (MULTI CH INPUT)

Audio input (PHONO)

16 En

Connections

y

• Input sources in parentheses are recommended to connect to the respective jacks. If your Yamaha component has the remote in/out terminal, you can

switch the input source to that component with a single key operation using the SCENE function (page 23).

• You can change the name of the input source displayed on the front panel display as necessary (page 52).

• See page 53 on how to use the ZONE2 OUT jacks.

• When you connect an external component with analog audio and component video (or composite) output jacks, connect the analog audio output to the

AUDIO 1 or AUDIO 2 jacks of this unit while making a video connection (component video or composite). Then select the video to be output when

“AUDIO 1” or “AUDIO 2” is selected as the input source (page 41).

■ Audio player

y

• We recommend connecting the coaxial digital output terminal of a CD player to the AV3 jack.

• When connecting a turntable with a low-output MC cartridge to the PHONO jacks, use an in-line boosting transformer or MC-head amplifier.

• Connect your turntable to the GND terminal of this unit to reduce noise in the signal.

■ Connecting a multi-format player or an

external decoder

This unit is equipped with 8 additional input jacks (Front

L/R, Center, Surround L/R, Surround Back L/R and

Subwoofer) for analog multi-channel input from a multi-

format player, external decoder, etc.

Notes

• When you select “MULTI CH” as the input source, the digital sound field

processor is automatically disabled.

• Since this unit does not redirect signals input at the MULTI CH INPUT

jacks to accommodate for missing speakers, connect at least a 5.1-

channel speaker system when using this feature.

• You can specify a video signal to be output during a multi-channel audio

reproduction (page 41). If your DVD player has analog multi-channel

output jacks, connect them to the MULTI CH INPUT jacks while making

a video connection (component video or composite).

Output jacks on the connected external component Input sources/jacks of this unit

External component Output jack Input source Input jack

External component with optical digital

output

Optical digital output AV 1 (TV) OPTICAL

AV 4 OPTICAL

External component with coaxial digital

output

Coaxial digital output AV 2 COAXIAL

AV 3 (CD) COAXIAL

External component with analog audio

output

Analog audio output AV 5 Analog audio

AV 6 Analog audio

AUDIO 1 Analog audio

AUDIO 2 Analog audio

Turntable Analog audio output PHONO Analog audio

About audio/video output terminals

Among the analog audio and analog video signals input to this unit via input terminals, the audio/video signals of the

selected input sources are output from the AV OUT jacks and AUDIO OUT jacks. An HDMI input signal,

COMPONENT VIDEO input signal or digital audio input signal cannot be output.

When using the AV OUT jacks: connect an external component to the VIDEO, S VIDEO or analog audio terminal.

When using the AUDIO OUT jacks: connect an external component to the analog audio terminal.

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

CENTER

LRLR RL

Surround

back out

Surround

out

Front out

Subwoofer out

Center out

Multi-format player or external decoder

(7.1-channel output)

17 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

■ Connecting an external amplifier

If you want to use another amplifier, connect an external

amplifier to the PRE OUT jacks. Each PRE OUT jack

outputs the same channel signals as the corresponding

speaker terminals.

Note

• When you make connections to the PRE OUT jacks, do not make any

connections to the speaker terminals.

a FRONT PRE OUT jacks

Front channel output jacks.

b SURROUND PRE OUT jacks

Surround channel output jacks.

c SUR.BACK PRE OUT jacks

Surround back output jacks. When you only connect one

external amplifier for the surround back channel, connect it to

the left SUR.BACK (SINGLE) jack.

y

• To output surround back channel signals at these jacks, set

“Surround Speaker” to any parameter except “None” (page 48).

d CENTER PRE OUT jack

Center channel output jack.

e SUBWOOFER PRE OUT 1/2 jack

Connect a subwoofer with a built-in amplifier.

■ Transmitting/receiving remote control signals

When the components have the capability of the

transmission of the remote control signals, connect the

REMOTE IN and REMOTE OUT jacks to the remote

control input and output jack with the monaural analog

mini cable as follows.

y

• If connecting a Yamaha component that supports the SCENE control

signal reception to the REMOTE OUT jack of this unit, you can start

playback on the Yamaha component by using the SCENE function

(page 23).

• If connecting a component other than Yamaha products to the REMOTE

OUT jack of this unit, set “SCENE IR” to “OFF” in the advanced setup

menu (page 57).

This unit has the DOCK terminal, to which you can

connect a Yamaha iPod universal dock (YDS-11, sold

separately) or a Bluetooth wireless audio receiver (YBA-

10, sold separately). You can play an iPod or a Bluetooth

component with this unit by connecting it to the DOCK

terminal.

Use a dedicated cable for connection between the dock/

receiver and this unit.

FRONT

SURROUND

SUR. BACK

SUBWOOFER

PRE OUT

CENTERSINGLE

1

2

abc d

e

IN

OUT

REMOTE

HDMI 1

B

D

/

DVD

)

HDMI

2

HDMI

3

HDMI 4

VIDE

O

MO

NIT

O

R

OU

T

P

R

P

B

Y

CO

MP

O

NEN

T

VIDE

O

Remote

control out

Remote

control in

Infrared signal

receiver or Yamaha

component

IR flasher or Yamaha

component

(CD or DVD player, etc.)

Connecting a Yamaha iPod universal

dock or Bluetooth™ wireless audio

receiver

DOCK

P

H

O

N

O

ANTENNA

CO

MP

O

NENT

VIDE

O

P

R

P

B

Y

V

IDE

O

GND

H

DMI OU

T

U

NBAL

.

F

M

G

N

D

S VIDE

O

A

Yamaha iPod universal dock or

Bluetooth wireless audio receiver

18 En

Connections

Connect a USB memory device or USB portable audio

player to the USB port on the front panel of this unit. For

information about USB storage devices supported by this

unit, see page 37.

Use the VIDEO AUX jacks on the front panel to connect a

game console or a video camera to this unit. Be sure to

turn down the volume of this unit and other components

before making connections.

An indoor FM antenna and an AM loop antenna are

supplied with this unit. Connect these antennas properly to

the respective jacks.

y

• The supplied antennas are normally sensitive enough to obtain good

reception.

• Position the AM loop antenna away from this unit.

• If you cannot get good reception, we recommend that you use an outdoor

antenna. For details, consult the nearest authorized Yamaha dealer or

service center.

• Always use the AM loop antenna even when the outdoor antenna is

connected.

Assembling the AM loop antenna

Connecting the AM loop antenna

The wires of the AM loop antenna have no polarity. You

can connect either wire to the AM terminal and the other

to the GND terminal.

Connecting a USB storage device

Using the VIDEO AUX jacks

U

S

B

S

TRAI

G

HT

PURE

D

IREC

T

INPUT

O

PTIMIZE

R

MIC

VIDE

O

A

U

DI

O

VIDE

O

AU

X

VO

L

U

ME

E

FFE

C

T

B

D

/

DV

D

TV

C

D

RADI

O

SC

EN

E

M

O

RY

PRE

S

ET

l

h

l

h

FM

AM

T

U

NIN

G

USB

USB memory device or

USB portable audio player

VIDEO

AUDIO

VIDEO

AUX

S

TRAI

G

HT

PURE

D

IREC

T

INPUT

O

PTIMIZE

R

MIC

U

S

B

VO

L

U

ME

E

FFE

C

T

B

D

/

DV

D

TV

C

D

RADI

O

SC

EN

E

M

O

RY

PRE

S

ET

l

h

l

h

FM

AM

T

U

NIN

G

R

L

AUDIO

VIDEO

V

L

R

Game console or video

camera

Analog audio

output

Video output

Connecting the FM and AM antennas

ANTENNA

UNBAL.

FM

GND

AM

DOC

K

PHONO

CO

MP

O

NEN

T

V

IDEO

P

R

P

B

Y

VIDE

O

GND

H

DMI OUT

S

VIDE

O

HDMI

1

(

BD

/

DV

D

)

HDMI 2

HD

M

V

IDE

O

IN

O

UT

MO

NIT

O

R

OU

T

TRI

GG

ER

OUT

1

2

V

0.1

A

MAX.

P

R

P

B

Y

REM

O

T

E

CO

MP

O

NENT

VIDE

O

Outdoor AM antenna

Connect a 5 to 10 m (16 to

33 ft) vinyl-covered wire,

and extend it outdoors

(use the AM loop antenna

together with this

antenna).

Ground (GND terminal)

The GND terminal is not for earth grounding.

To reduce noises, connect a ground bar or a

vinyl-covered wire with a copper plate at its tip,

and place it in the moist ground.

Indoor FM antenna

AM loop

antenna

Press and hold ReleaseInsert

Sivu latautuu ...

Yamaha RX-V1065 Omistajan opas

Yamaha RX-V1065 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat