Yamaha RX V3900 - AV Network Receiver Ohjekirja

Printed in Malaysia WP55260

RX-V3900

AV R e c e i ve r

OWNER’S MANUAL

U

RX-V3900_U-cv.fm Page 1 Friday, August 8, 2008 3:06 PM

Black process 45.0° 240.0 LPI

Caution-i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifications

not expressly approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2 IMPORTANT:

When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3NOTE:

This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the users

manual, may cause interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Caution-ii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press

A

MASTER ON/OFF to

release it outward to the OFF position to turn off this unit, the

main room, Zone 2 and Zone 3 and then disconnect the AC

power plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

................................AC 110/120/220/230–240 V, 50/60 Hz

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by

A

MASTER ON/OFF. In

this state, this unit is designed to consume a very small

quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de

la prise et pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à

la norme NMB-003 du Canada.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

Caution-iii En

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of

Dolby Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535

& other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and

“iPod” is a trademark of Apple Inc., registered in the U.S. and

other countries.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

This receiver supports network connections.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

The XM name and related logos are registered trademarks of XM

Satellite Radio Inc.

This product is manufactured under license from Neural Audio

Corporation and THX Ltd. YAMAHA CORPORATION hereby

grants the user a non-exclusive, non-transferable, limited right of

use to this product under U.S.A. and foreign patent, patent

pending and other technology or trademarks owned by Neural

Audio Corporation and THX Ltd. “Neural Surround”, “Neural

Audio”, “Neural” and “NRL” are trademarks and logos owned by

Neural Audio Corporation. THX is a trademark of THX Ltd.,

which may be registered in some jurisdictions. All rights

reserved.

the SIRIUS dog logo, channel names and logos are trademarks of

SIRIUS Satellite Radio Inc.

HD Radio™ Technology Manufactured Under License From

iBiquity Digital Corp. U.S. and Foreign Patents. HD Radio™ and

the HD Radio logo are proprietary trademarks of iBiquity Digital

Corp.

Rhapsody and the Rhapsody logo are registered trademarks of

RealNetworks, Inc.

Circle Surround II, Dialog Clarity, TruBass, SRS and the

symbol are trademarks of SRS Labs, Inc.

Circle Surround II, Dialog Clarity and TruBass technologies are

incorporated under license from SRS Labs, Inc.

Windows XP, Windows Vista, Windows Media Audio, Windows

Media Connect and Windows Media Player are either registered

trademarks or trademarks of Microsoft corporation in the United

States and/or other countries.

iPod

TM

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

English

Features ................................................................... 3

Supplied accessories .................................................. 3

Getting started ........................................................ 4

Quick start guide .................................................... 5

L

Connections ............................................................. 9

Optimizing the speaker setting for your

listening room.................................................... 30

Playback ................................................................ 36

Basic procedure ....................................................... 36

Selecting audio input jacks (AUDIO SELECT)...... 37

Selecting the multi-channel input component ......... 37

Selecting the HDMI OUT jack ................................ 37

Using your headphones............................................ 38

Muting the audio output........................................... 38

Displaying the input source information ................. 38

Using the sleep timer ............................................... 39

Sound field programs ........................................... 40

Selecting sound field programs ............................... 40

Using CINEMA DSP 3D mode............................... 46

Enjoying unprocessed input sources........................ 46

Using audio features ............................................. 47

Enjoying pure hi-fi sound ........................................ 47

Adjusting the tonal quality....................................... 47

Adjusting the speaker level...................................... 47

Selecting the recording source................................. 47

FM/AM tuning ...................................................... 48

Overview.................................................................. 48

FM/AM tuning operations ....................................... 48

Preset FM/AM stations ............................................ 49

Using HD Radio™ features

(U.S.A. model only)........................................... 51

Selecting HD Radio™ audio programs ................... 51

Using the iTunes Tagging feature............................ 51

Displaying HD Radio™ information....................... 52

XM

®

Satellite Radio tuning ................................. 53

Connecting XM Mini-Tuner Home Dock ............... 53

Activating XM Satellite Radio ................................ 54

XM Satellite Radio operations................................. 54

Setting the XM Satellite Radio preset channels ...... 55

Displaying the XM Satellite Radio information...... 56

SIRIUS Satellite Radio™ tuning......................... 58

Connecting the SiriusConnect™ tuner .................... 58

Activating SIRIUS Satellite Radio™

subscription ......................................................... 59

SIRIUS Satellite Radio™ operations ...................... 59

Setting the SIRIUS Satellite Radio™

preset channels .................................................... 61

Setting the Parental Lock......................................... 62

Displaying the SIRIUS Satellite Radio™

information .......................................................... 63

Using Bluetooth™ components ........................... 64

Pairing the Bluetooth™ receiver and your

Bluetooth component .......................................... 64

Playback of the Bluetooth™ component ................. 64

Music Content menu ............................................ 65

Music Content menu operations .............................. 65

Using iPod™ ..........................................................66

iPod menu tree ......................................................... 66

Controlling iPod™................................................... 67

Using USB and network features.........................68

USB and network menu tree.................................... 68

Navigating USB and network menus ...................... 69

Using a USB storage device or a USB portable

audio player ......................................................... 69

Using a PC server or Yamaha

MCX-2000........................................................... 70

Using the Internet Radio.......................................... 71

Using the Rhapsody® service

(U.S.A. model only) ............................................ 71

Using shortcut buttons ............................................. 72

Advanced sound configurations...........................74

Selecting decoders ................................................... 74

Graphical user interface (GUI) menu .................76

GUI menu overview ................................................ 78

GUI menu operations............................................... 79

Saving and recalling the system settings

(System Memory) ............................................101

Controlling this unit by using the Web

browser (Web Control Center) ......................105

Remote control features......................................106

Controlling this unit, a TV,

or other components .......................................... 106

Customizing the remote control ............................ 108

Setting the backlight mode of the remote

control................................................................ 109

Setting remote control codes ................................. 109

Programming codes from other remote controls ... 111

Changing source names in the display window..... 112

Macro programming features ................................ 113

Clearing configurations ......................................... 115

Simplified remote control...................................... 116

Using multi-zone configuration..........................117

Connecting the Zone 2 and Zone 3 components ... 117

Controlling Zone 2 or Zone 3 ................................ 119

Advanced setup....................................................121

Using the advanced setup menu ............................ 121

Troubleshooting...................................................124

Resetting the system............................................138

Operation modes of front panel controls ..........139

Glossary................................................................140

Sound field program information......................143

Parametric equalizer information .....................144

Specifications .......................................................145

Index .....................................................................147

(at the end of this manual)

Front panel................................................................i

Remote control ....................................................... ii

Sound output in each sound field program......... iii

List of remote control codes ...................................v

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX

2 En

By configuring the parameters in the GUI menu of this unit, you can adjust a variety of system settings suited for your

listening environment. The following is a brief description of some of the useful menus you can configure in the GUI

menu. For more detailed information, see “Graphical user interface (GUI) menu” (page 76).

Fine adjusting the speaker settings

In case speaker settings configured by automatic setup

does not match your listening environment, you can

configure them manually.

Setup → Speaker (page 87)

Specifying the muting type

In case you do not want to fully mute audio when you

receive a call while watching your favorite TV program,

you can use this menu to specify the muting level.

Setup → Vo l um e → Muting Type (page 90)

Specifying the initial volume level

By adjusting this parameter, you can automatically control

the initial volume level regardless of the recording level of

the audio source.

Setup → Vo l um e → Initial Volume (page 90)

Adjusting the dynamic range

The dynamic range is the difference between the

minimum and maximum amplitude. The higher the

dynamic range, the more accurate the sound reproduction

for bitstream signals. You can adjust the dynamic range

for speakers and headphones individually. Also, you can

use the adaptive dynamic range control feature to adjust

the dynamic range automatically in conjunction with the

volume level.

Setup → Sound → Dynamic Range (page 90)

Setup → Vo l um e → Adaptive DRC (page 89)

Adjusting the audio and video synchronization

Sometimes, depending on your video source component,

video is delayed relative to audio due to processing

problems. In this case, you need to manually adjust the

audio delay to keep it synchronized with the video. If you

connect the video source component to this unit using an

HDMI connection and your component supports the

LIPSYNC feature, you can adjust the audio/video

synchronization automatically.

Setup → Sound → Lipsync (page 92)

Changing input/output assignment

In case the initial input/output assignments do not

correspond to your needs, you can rearrange them

according to your component to be connected to this unit.

You can also edit the input name to be displayed in the

front panel or in the GUI screen as necessary.

Setup → Option → I/O Assignment (page 98)

Setup → Option → Input Rename (page 98)

Fixing the volume difference between input

sources

The sound output level may vary depending on the audio

source components connected to this unit. In this case, you

can reduce or increase the output level of each input

source using this feature.

Input Select → (input source) → (submenu) →

Volume Trim (page 85)

Setting the background video for discrete multi-

channel input

If you want to enjoy video images in combination with

discrete multi-channel audio input, configure this setting

to specify the video input source. For example, to view

DVD video images while listening to the music sources

from a multi-format player or an external decoder, set this

setting to “DVD”.

Input Select → MULTI CH → (submenu) → BGV

(page 86)

Adjusting the brightness of the front panel

display

You can make the front panel display darker or brighter by

configuring this setting.

Setup → Option → Display Set → Front Panel Display →

Dimmer (page 98)

Turning on or off the short message display

Each time you operate this unit using controls on the front

panel or remote control keys, this unit displays short

messages on the video monitor. If you want to turn off the

short message display, select “Off” in this setting (Initial

factory setting is “On”).

Setup → Option → Display Set → Short Message

(page 98)

Setting the amount of time to display GUI screen

information

You can set the amount of time to display playback

information in the GUI screen after you perform a certain

operation.

Setup → Option → Display Set → Playback Screen

(page 98)

Protecting the setup values

After you have configured the sound field program

parameters and other system settings, you can use this

feature to prevent accidental changes to those setup

values.

Setup → Option → Memory Guard (page 97)

What you can do with the GUI menu

FEATURES

3 En

INTRODUCTION

English

Built-in 7-channel power amplifier

◆

Minimum RMS output power

(20 Hz to 20 kHz, 0.04% THD, 8

Ω

)

Front: 140 W + 140 W

Center: 140 W

Surround: 140 W + 140 W

Surround back: 140 W + 140 W

Various input/output connectors

◆

HDMI (IN x 4, OUT x 2), Component video (IN x 3, OUT x 1), S-

video (IN x 6, OUT x 3), Composite video (IN x 6, OUT x 5),

Coaxial digital audio (IN x 3), Optical digital audio (IN x 5, OUT x

2), Analog audio (IN x 10, OUT x 3)

◆

Speaker out (7-channel), Pre out (7-channel), Subwoofer out,

Presence out, Zone 2/Zone 3 out

◆

Discrete multi-channel input (6 or 8-channel)

Sound field programs

◆

Proprietary Yamaha technology for the creation of sound fields

◆

CINEMA DSP 3D

◆

Compressed Music Enhancer mode

◆

Virtual CINEMA DSP

◆

SILENT CINEMA

Digital audio decoders

◆

Dolby TrueHD, Dolby Digital Plus decoder

◆

DTS-HD Master Audio, DTS-HD High Resolution Audio decoder

◆

Dolby Digital/Dolby Digital EX decoder

◆

DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS 96/24 decoder

◆

Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx decoder

◆

DTS NEO:6 decoder

◆

Neural-THX Surround decoder

(U.S.A. and Canada models only)

◆

SRS Circle Surround II decoder (U.S.A. model only)

Radio tuners

◆

FM/AM tuning capability, 40-station preset tuning

◆

HD Radio™ digital broadcast reception capability (U.S.A. model

only)

◆

XM Satellite Radio tuning capability (using XM Mini-Tuner and

Home Dock, sold separately)

◆

SIRIUS Satellite Radio™ tuning capability (using SiriusConnect

tuner, sold separately)

HDMI™ (High-Definition Multimedia Interface)

◆

HDMI interface for standard, enhanced or

high-definition video as well as multi-channel digital audio based on

HDMI version 1.3a (HDMI is licensed by HDMI Licensing, LLC.)

– Automatic audio and video synchronization (lip sync) information

capability

– Deep Color video signal (30/36 bit) transmission capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals capability

– High definition digital audio format signals capability

◆

HDCP (High-bandwidth Digital Content Protection System) licensed

by Digital Content Protection, LLC.

◆

Analog video to HDMI digital video up-conversion (composite video

↔

S-video

↔

component video

→

HDMI digital video) capability

for monitor out

◆

Analog and HDMI video up-scaling: 480i(576i)

→

480p(576p)/

720p/1080i/1080p, 480p(576p)

→

720p/1080i/1080p, 720p

→

1080i/1080p, 1080i

→

720p/1080p

DOCK terminal

◆

DOCK terminal to connect a Yamaha iPod universal dock (such as

YDS-11, sold separately) or Bluetooth wireless audio receiver (such

as YBA-10, sold separately)

USB and network features

◆

USB port to connect a USB storage device, USB Hard disc

drive, or USB portable audio player

◆

NETWORK port to connect a PC and Yamaha MCX-2000 or

access the Internet Radio and Rhapsody

®

(U.S.A. model

only) via LAN

◆

DHCP automatic or manual network configuration

◆

Web control capability of this unit by using a Web browser

Automatic speaker setup features

◆

Advanced YPAO (Yamaha Parametric room Acoustic Optimizer) for

automatic speaker setup

◆

Multi-point measurement feature for multiple listening positions

◆

Parametric equalizer select feature

Other features

◆

192-kHz/24-bit D/A converter

◆

GUI (graphic user interface) menus that allow you to optimize this

unit to suit your individual audiovisual system

◆

Music Content menu that allows you to easily navigate music content

menus of your iPod, USB component, Internet Radio, etc.

◆

PURE DIRECT mode for pure hi-fi sound for all sources

◆

Adaptive dynamic range controlling capability

◆

Adaptive DSP effect level controlling capability

◆

Remote control with preset remote control codes, learning and macro

capability

◆

ZONE 2/ZONE 3 custom installation facility

◆

Zone switching capability between the main zone and

ZONE 2/ZONE 3 using ZONE CONTROLS

◆

System Memory capability for saving and recalling multiple system

parameter settings

◆

Sleep timer for each zone

Check that you received all of the following parts.

❏ Remote control

❏ Simplified remote control

❏ Batteries (4) (AAA, LR03, UM-4)

❏ Power cable (Two for Asia model)

❏ Optimizer microphone

❏ AM loop antenna

❏ Indoor FM antenna

Features

Supplied accessories

GETTING STARTED

4 En

■ Installing batteries in the remote control

1 Take off the battery compartment cover.

2 Insert the four supplied batteries

(AAA, LR03, UM-4) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the transmit indicator does not flash or its light becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries, set up the remote control code

and program any acquired functions that may have been

cleared.

■ VOLTAGE SELECTOR

(Asia and General models only)

Getting started

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the

buttons on the front panel or the ones on the remote

control. In case the button names differ between the front

panel and the remote control, the button name on the

remote control is given in parentheses.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and product, the product has priority.

•“

A

MASTER ON/OFF” or “

3

DVD” (example)

indicates the name of the parts on the front panel or the

remote control. Refer to the attached sheet or the pages at

the end of this manual for the information about each

position of the parts.

1

3

2

Notes

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

Voltages are as follows:

........................AC 110/120/220/230–240 V, 50/60 Hz

230-

240V

VOLTAGE

SELECTOR

Voltage indication

QUICK START GUIDE

5 En

INTRODUCTION

English

The following steps describe the easiest way to enjoy DVD movie playback in your home theater.

In these steps, you need the following supplied

accessories.

❏ Power cable

The following items are not included in the package of this

unit.

❏ Speakers

❏ Front speaker ......................................x 2

❏ Center speaker ...................................x 1

❏ Surround speaker ...............................x 4

Select magnetically shielded speakers. The

minimum required speakers are two front speakers.

The priority of the requirement of other speakers is

as follows:

1. Two surround speakers

2. One center speaker

3. One (or two) surround back speaker(s)

❏ Active subwoofer ....................................x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cable ..........................................x 7

❏ Subwoofer cable .....................................x 1

Select a monaural RCA cable.

❏ DVD player ...............................................x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output

jack.

❏ Video monitor...........................................x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ..............................................x 2

Select RCA composite video cables.

❏ Digital coaxial audio cable .....................x 1

Quick start guide

Front right

speaker

Subwoofer

Surround back

right speaker

Surround left

speaker

Front left

speaker

Surround back left

speaker

Surround right

speaker

Center

speaker

Video monitor

DVD player

Enjoy DVD playback!

Step 1: Set up your speakers

☞

P. 6

Step 2: Connect your DVD player

and other components

Step 3: Turn on the power and

start playback

☞

P. 7

☞

P. 8

Preparation: Check the items

Quick start guide

6 En

Place your speakers in the room and connect them to this

unit.

1 Place your speakers and subwoofer in the

room.

2 Connect speaker cables to each speaker.

3 Connect each speaker cable to the

corresponding speaker terminal of this unit.

1 Make sure that this unit and the subwoofer are

unplugged from the AC wall outlets.

2 Twist the exposed wires of the speaker cables

together to prevent short circuits.

3 Do not let the bare speaker wires touch each other.

4 Do not let the bare speaker wires touch any metal

part of this unit.

Be sure to connect the left channel (L), right channel

(R), “+” (red) and “–” (black) properly.

Front speakers and center speaker

Surround and surround back speakers

4 Connect the subwoofer cable to the

SUBWOOFER PRE OUT jack of this unit and

the input jack of the subwoofer.

Step 1: Set up your speakers

AC IN

AC OUTLETS

SWITCHED

SPEAKERS

CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

NETWORK

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUDIO

DOCK

XM

SIRIUS

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB SUR.BACK

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3 ZONE

VIDEO

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

(8CH)

DVD

OUT(REC)

IN(PLAY)

MD/CD-R

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD DVD CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN 1 2

OUT IN OUT

DVR

CBL/

SAT

OUT

1

OUT

2

+

A B C

R

L

R

L

+

R

L

+

R

L

+

R

L

+

R

L

IN1

IN3

DVD

BD/

HD DVD

IN2

IN4

SP1

SP2

SUBWOOFER PRE OUT Speaker terminals

12 3 4

To the front left

speaker

To the front right

speaker

Loosen Insert

To the center

speaker

Tighten

To the surround

back

right speaker

To the surround

left speaker

To the surround back

left speaker

To the surround right

speaker

SUBWOOFER PRE OUT jack

Input jack

AV receiverSubwoofer

Subwoofer cable

Quick start guide

7 En

INTRODUCTION

English

1 Connect the digital coaxial audio cable to the

digital coaxial audio output jack of your DVD

player and the DVD DIGITAL INPUT COAXIAL

jack of this unit.

2 Connect the video cable to the composite

video output jack of your DVD player and

DVD VIDEO jack of this unit.

3 Connect the video cable to the VIDEO

MONITOR OUT jack of this unit and the video

input jack of your video monitor.

4 Connect the supplied power cable to this unit

and then plug of the power cable and other

components into the AC wall outlet.

y

For details about connecting the power cable, see page 25.

■ For other connections

• Other speaker combinations ☞ P. 12

• Information on jacks and cable plugs ☞ P. 15

• Information on HDMI™ ☞ P. 16

• TV monitor or projector ☞ P. 18

• Other components ☞ P. 19

• External amplifier ☞ P. 21

• Multi-format player or external

decoder ☞ P. 22

• Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞ P. 22

•FM/AM antennas ☞ P. 24

• XM Mini-Tuner Home Dock ☞ P. 53

• SiriusConnect tuner ☞ P. 58

•Network ☞ P. 23

•USB device ☞ P. 23

Step 2: Connect your DVD player

and other components

AC IN

AC OUTLETS

SWITCHED

SPEAKERS

CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

NETWORK

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUDIO

DOCK

XM

SIRIUS

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB SUR.BACK

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3 ZONE

VIDEO

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

(8CH)

DVD

OUT(REC)

IN(PLAY)

MD/CD-R

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD DVD CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN 1 2

OUT IN OUT

DVR

CBL/

SAT

OUT

1

OUT

2

+

A B C

R

L

R

L

+

R

L

+

R

L

+

R

L

+

R

L

IN1

IN3

DVD

BD/

HD DVD

IN2

IN4

SP1

SP2

Make sure that this unit and the DVD

player are unplugged from the AC

wall outlets.

VIDEO MONITOR OUTDVD VIDEO

DVD DIGITAL INPUT

COAXIAL

Digital coaxial

audio output

jack

Digital coaxial audio

cable

DVD DIGITAL INPUT

COAXIAL jack

DVD player

AV receiver

Composite video

output jack

Video cable

DVD VIDEO jack

DVD player

AV receiver

Video monitor

AV receiver

Video cable

VIDEO MONITOR

OUT jack

Video input jack

Quick start guide

8 En

1 Turn on the video monitor connected to this

unit.

2 Press AMASTER ON/OFF inward to the ON

position on the front panel.

3 Rotate the

C

INPUT selector to set the input

source to “DVD”.

4 Start playback of the desired DVD on your

player.

5 Rotate

P

VOLUME to adjust the volume.

6 To set this unit to the standby mode, press

BMAIN ZONE ON/OFF.

y

For details about turning on/off this unit and the standby

mode, see page 26.

■ For other operations

• Optimizing the speaker parameters

automatically ☞ P. 30

• Basic playback operations ☞ P. 36

• Sound field programs ☞ P. 40

• Pure high-fidelity sounds ☞ P. 47

• FM/AM radio tuning ☞ P. 48

• XM Satellite Radio tuning ☞ P. 53

• SIRIUS Satellite Radio tuning ☞ P. 58

• Bluetooth component playback ☞ P. 64

• iPod playback ☞ P. 66

• Playback via USB or network ☞ P. 68

Step 3: Turn on the power and start

playback

Check the type of the connected speakers.

If the speakers are 6-ohm speakers, set “SPEAKER

IMP.” to “6Ω MIN” before using this unit (page 26).

You can also use 4-ohm speakers as the front speakers

(page 121).

9 En

PREPARATION

English

The RS-232C terminal is a control expansion terminal for

factory use only. Consult your dealer for details.

Connections

Rear panel

AC IN

AC OUTLETS

SWITCHED

SPEAKERS

CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

NETWORK

ANTENNA

FM

GND

AM

75Ω UNBAL.

VIDEO

S VIDEO

MONITOR OUT

VIDEO

REMOTE

PHONO

GND

CD TV

HDMI

COMPONENT VIDEO

AUD IO

DOCK

XM

SIRIUS

DIGITAL INPUT

MULTI CH INPUT

PRE OUT

TRIGGER OUT

RS-232C

DIGITAL OUTPUT

ZONE OUT

SUB SUR.BACK

WOOFER

SUB

WOOFER

CENTER

FRONT(6CH)

FRONT

SURROUND

PRESENCE

SUR.BACK/

SINGLE(SB)

ZONE 2

ZONE 3 ZONE

VIDEO

CD

D

V

D

V

R

COAXIAL

1

2

TV

BD/

HD DVD

CBL/

SAT

MD/

CD-R

DVD DVR

OPTICAL

987

65

4

321

(8CH)

DVD

OUT(REC)

IN(PLAY)

MD/CD-R

BD/HD DVD

VCR

DVR

CBL/SAT

OUT OUT

ININ

BD/HD DVD DVD CBL/SAT

MONITOR OUT

Y

P

R

Y

P

R

P

B

P

B

IN 1 2

OUT IN OUT

DVR

CBL/

SAT

OUT

1

OUT

2

+

A B C

R

L

R

L

+

R

L

+

R

L

+

R

L

+

R

L

IN1

IN3

DVD

BD/

HD DVD

IN2

IN4

SP1

SP2

BCA0

9

D

231456 78

Name Page

1 HDMI jacks 16

2 COMPONENT VIDEO jacks 15

3 Audio component jacks 15

REMOTE IN/OUT jacks 22, 117

4 Video component jacks 15

5 ANTENNA terminals 24

6 NETWORK port 23

7 VOLTAGE SELECTOR

(Asia and General models only)

25

8 AC IN 25

AC OUTLET(S) 25

9 DOCK terminal 22

0 XM jack (U.S.A. and Canada models only) 53

SIRIUS jack

(U.S.A. and Canada models only)

58

A DIGITAL INPUT/OUTPUT jacks 15

B TRIGGER OUT jacks 119

C RS-232C terminal —

D MULTI CH INPUT jacks 22

PRE OUT jacks 21

ZONE OUT jacks 117

Speaker terminals 12

Note

Name Page

10 En

Connections

The speaker layout below shows the speaker setting we recommend.

y

• 7.1-channel speaker layout is highly recommended for playback of the high definition digital audio sources (Dolby TrueHD, DTS-HD

Master Audio, etc.) with sound field programs.

• We recommend that you add the presence speakers for the effect sounds of the CINEMA DSP sound field program.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

Placing speakers

FR

FL

SBR

SBL

SL

SR

C

SW

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

FR

FL

SB

SL

SR

C

SW

FR

FL

SL

SR

SW

C

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

11 En

Connections

PREPARATION

English

■ Speaker types

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers at an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

For 5.1-channel speaker layout, place these speakers

farther back compared with the placement in the 7.1-

channel speaker layout.

Surround back left and right speakers (SBL and

SBR) /Surround back speaker (SB)

The surround back speakers supplement the surround

speakers and provide more realistic front-to-back

transitions.

For 6.1-channel speaker layout, surround back left and

right channel signals are mixed down and output at the

single surround back speaker by configuring the

“Surround Back” setting (

page 88

).

For 5.1-channel speaker layout, surround back left and

right channel signals are output at the surround left and

right speakers by configuring the “Surround Back” setting

(

page 88

).

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as

the Yamaha Active Servo Processing Subwoofer System,

is effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the high

fidelity sound of the LFE (low-frequency effect) channel

included in bitstreams and multi-channel PCM sources.

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the front speakers. Turn it

slightly toward the center of the room to reduce wall

reflections.

■ Presence left and right speakers (PL and

PR)

The presence speakers supplement the sound from the front

speakers with extra ambient effects produced by the sound

field programs (page 40). We recommend that you use the

presence speakers especially for the CINEMA DSP sound

field programs. To use the presence speakers, connect the

speakers to SP1 speaker terminals and then set

“

Front

Presence

”

to

“

Yes

”

(page 88).

For other speaker combinations

You can enjoy multi-channel sources with sound field

programs by using a speaker combination other than

the 7.1/6.1/5.1-channel speaker combinations.

Use the automatic setup feature (page 30) or set the

“Speaker” parameters (

page 87

). to output the surround

sounds at the connected speakers.

FR

PRPL

C

FL

1.8 m (6 ft)

0.5 to 1 m (1 to 3 ft) 0.5 to 1 m (1 to 3 ft)

1.8 m (6 ft)

12 En

Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

this unit cannot reproduce the input sources accurately.

• A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the

plain cable to the “–” (black) terminals.

• You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. This unit

automatically switches the presence speakers and surround back speakers depending on the input sources and the selected sound field

programs.

■ 7.1-channel speaker connection

Connecting speakers

Caution

• Before connecting the speakers, make sure that this unit is turned off (page 26).

• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the

speakers away from the monitor.

• If you are to use 6-ohm speakers, be sure to set “SPEAKER IMP.” to “6Ω MIN” before using this unit (page 26).

You can also use 4-ohm speakers as the front speakers (page 121).

Notes

SPEAKERS

CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

SUB

WOOFER

+

R

L

+

R

L

+

R

L

+

R

L

+

R

L

SP1

SP2

Front speakers

Surround speakers

Presence speakers

(page 11) or

Zone 2/Zone 3

speakers

(page 117)

Subwoofer

Right

Center speaker

Surround back speakers

Left

Left Left

RightRight

Zone 2/Zone 3 speakers

(page 117)

13 En

Connections

PREPARATION

English

■ 6.1-channel speaker connection

■ 5.1-channel speaker connection

Surround back speaker

SPEAKERS

CENTERPRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

SUB

WOOFER

+

L

+

R

L

+

R

L

+

R

L

+

R

L

SP1

SP2

Surround speakers

Front speakers

Presence speakers

(page 11) or

Zone 2/Zone 3 speakers

(page 117)

Subwoofer

Center speaker

Left

Right

Zone 2/Zone 3

speakers

(page 117)

SPEAKERS

CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3

FRONT SURROUND ZONE 2/ZONE 3

SINGLE

K

SUB

WOOFER

+

R

L

+

R

L

+

R

L

+

R

L

+

R

L

SP1

SP2

Surround speakersFront speakers

Subwoofer

Center speaker

Left

LeftRight Right

Zone 2/Zone 3

speakers

(page 117)

Front speakers for the

bi-amplification

connections

(page 14)

Presence speakers

(page 11) or

Zone 2/Zone 3 speakers

(page 117)

14 En

Connections

■ Connecting the speaker cable

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist the exposed wires of the

cable together to prevent short circuits.

2 Loosen the knob, insert one bare wire into

the hole and then tighten the knob.

■ Connecting the banana plug

(Except U.K., Europe, Asia and Korea

models)

Tighten the knob and then insert the banana plug

into the end of the terminal.

■ Using bi-amplification connections

You can make bi-amplification connections to one speaker

system which supports bi-amplification connection as

shown below. To activate the connections, configure the

“BI-AMP” setting (page 122).

When you make the conventional connection with the speakers,

make sure that the shorting bars are put into the terminals of the

speakers appropriately. Refer to the instruction manuals of the

speakers for details.

10 mm (0.4 in)

Loosen Insert Tighten

Banana plug

Caution

Remove the shorting bars or bridges of your speakers to

separate the LPF (low pass filter) and HPF (high pass filter)

crossovers.

Note

SURROUND BACK/BI-AMP

FRONT

SINGLE

+

R

L

+

R

L

This unit

LeftRight

Front speakers

15 En

Connections

PREPARATION

English

This unit has three types of audio jacks, three types of video jacks and HDMI jacks. You can choose the connection

method depending on the component to be connected.

■ Audio jacks

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both the

COAXIAL and OPTICAL jacks, priority is given to the signals

input at the COAXIAL jack. All digital input jacks are

compatible with up to 96-kHz sampling digital signals.

■ Video jacks

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

COMPONENT VIDEO jacks

For component video signals, separated into the

luminance (Y) and chrominance (P

B, PR) video signals

transmitted on separate wires of component video cables.

y

This unit is equipped with the video conversion function.

(page 17)

Information on jacks and cable plugs

Note

COAXIAL

DIGITAL

AUDIO

OPTICAL

DIGITAL

R

L

C

O

R

L

Left and right

analog audio

cable plugs

Optical

digital

audio cable

plug

Coaxial

digital audio

cable plug

(Red)(White) (Orange)

VIDEO S VIDEO

COMPONENT VIDEO

Y

R

P

B

P

PB

Y

P

R

S

V

Composite

video cable

plug

S-video

cable plug

Component

video cable

plugs

(Yellow) (Green) (Blue) (Red)

16 En

Connections

This unit has four HDMI input jacks and two HDMI output jacks for digital audio and video signal input/output.

■ HDMI jack and cable plug

y

• We recommend that you use a commercially available HDMI cable

shorter than 5 meters (16 feet) with the HDMI logo printed on it.

• Use a conversion cable (HDMI jack

↔

DVI-D jack) to connect this

unit to other DVI components.

• You can check the potential problem about the HDMI connection

(page 38).

• If you set “Mode” in “Standby Through” to “Last” or “Fix”, this

unit allows the HDMI signals input at an HDMI IN jack to pass

through this unit and output at an HDMI OUT jack (page 94).

• This unit is equipped with two HDMI OUT jacks. You can select

the active HDMI OUT jack(s) (page 37).

• This unit is equipped with the video conversion function (page 17).

• Do not disconnect or connect the cable or turn off the power of

the HDMI components connected to the HDMI OUT jacks of

this unit while data is being transferred. Doing so may disrupt

playback or cause noise.

• The HDMI OUT jacks output the audio signals input at the

HDMI input jacks only.

• If you turn off the video monitor connected to the HDMI OUT

jacks via a DVI connection, the connection may fail.

■ HDMI signal compatibility with this unit

Audio signals

y

• If the input source component can decode the bitstream audio

signals of audio commentaries, you can play back the audio sources

with the audio commentaries mixed down by using the following

connections:

– multi-channel analog audio input (page 22)

– DIGITAL INPUT OPTICAL (or COAXIAL)

• Refer to the instruction manuals of the input source component,

and set the component appropriately.

• When CPPM copy-protected DVD audio is played back, video and

audio signals may not be output depending on the type of the DVD

player.

• This unit is not compatible with HDCP-incompatible HDMI or

DVI components.

• To decode the audio bitstream signals on this unit, set the input

source component appropriately so that the component outputs the

audio bitstream signals directly (does not decode the bitstream

signals on the component).

• This unit is not compatible with the audio commentary features (for

example, the special audio contents downloaded via Internet) of

Blu-ray Disc or HD DVD. This unit does not play back the audio

commentaries of the Blu-ray Disc or HD DVD contents.

Video signals

This unit is compatible with the video signals of the

following resolutions:

– 480i/60 Hz

– 576i/50 Hz

– 480p/60 Hz

– 576p/50 Hz

– 720p/60 Hz, 50 Hz

– 1080i/60 Hz, 50 Hz

– 1080p/60 Hz, 50 Hz, 24Hz

Compatibility with Deep Color and x.v.Color

video signals

This unit accepts Deep Color (30 or 36-bit) and x.v.Color

video signals. To output those video signals from the

HDMI OUT jacks without any processing, set “HDMI `

HDMI” (page 94)” to “Through”.

If the video monitor is not compatible with Deep Color or

x.v.Color video signals, the video source may not be played

back correctly.

■ Default input assignment of HDMI input

jacks

Information on HDMI™

Notes

Audio signal

types

Audio signal

formats

Compatible

media

2ch Linear

PCM

2ch, 32-192 kHz,

16/20/24 bit

CD, DVD-Video,

DVD-Audio, etc.

Multi-ch

Linear PCM

8ch, 32-192 kHz,

16/20/24 bit

DVD-Audio, etc.

DSD 2/5.1ch,

2.8224 MHz,1 bit

SA-CD, etc.

Bitstream Dolby Digital,

DTS

DVD-Video, etc.

Bitstream (High

definition audio)

Dolby TrueHD,

Dolby Digital Plus,

DTS-HD Master

Audio, DTS-HD

High Resolution

Audio

Blu-ray Disc,

HD DVD, etc.

HDMI

HDMI cable plug

Notes

Note

HDMI input jack Assigned input source

IN1 BD/HD DVD

IN2 DVD

IN3 CBL/SAT

IN4 DVR

Sivu latautuu...

Yamaha RX V3900 - AV Network Receiver Ohjekirja

Tämä ohje sopii myös

Yamaha RX V3900 - AV Network Receiver Ohjekirja

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat