Yamaha MCR-B043 White Ohjekirja

G

English Français Deutsch

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

Micro Component System

Micro-Chaîne

Svenska Italiano Español

Nederlands

Русский

MCR-B043

MCR-B043D

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place -

away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a

lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the

wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the unit to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn off, then leave this unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

– Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or

her mouth.

– If the batteries grow old, the effective operation range of

the remote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

– Do not use old batteries together with new ones.

– Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have the

same shape and color.

– Exhausted batteries may leak. If the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

– If you plan not to use the unit for a long period of time,

remove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery

liquid that may damage the unit.

– Do not throw away batteries with general house waste.

Dispose of them correctly in accordance with your local

regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

based (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English

NAMES OF PARTS AND THEIR FUNCTIONS ........2

Front panel.....................................................................2

Front panel display.........................................................2

Remote control...............................................................3

CONNECTIONS ........................................................4

Connecting the speakers and antenna ..........................4

Connecting the power cable...........................................5

Other connections..........................................................5

About the standby state .................................................5

ADJUSTING THE CLOCK (OPTION MENU) ...........6

LISTENING TO CD AND USB DEVICES .................7

Listening to a CD............................................................7

Listening to a USB device..............................................8

Using repeat/shuffle playback (remote control only)......8

LISTENING TO MUSIC FROM YOUR Bluetooth

COMPONENT............................................................9

Playing back from your Bluetooth component................9

Connecting an already-paired component via

Bluetooth

... 10

Disconnecting a Bluetooth connection.........................10

LISTENING TO DAB STATIONS (MCR-B043D only) ...11

Preparing for DAB reception ........................................11

Selecting DAB stations.................................................12

Presetting DAB stations (remote control only) .............13

Selecting preset DAB stations......................................14

Checking the signal strength of DAB stations

(Option menu) ..............................................................14

LISTENING TO FM STATIONS ..............................15

Selecting an FM station................................................15

Presetting FM stations (remote control only) ...............16

Selecting preset FM stations........................................17

LISTENING TO EXTERNAL SOURCES ................17

USEFUL FUNCTIONS ............................................18

Using the Option menu ................................................18

Using the sleep timer ...................................................19

Using the alarm function (IntelliAlarm) .........................19

Setting the alarm ..........................................................20

Operations while the alarm sound is playing................21

TROUBLESHOOTING ............................................22

NOTES ON DISCS AND USB DEVICES................25

SPECIFICATIONS...................................................26

CONTENTS

• Play back music from external devices such as your audio/data CDs, USB devices, or external devices via the AUX jack,

and listen to the radio.

• (MCR-B043D only) Listen to the DAB radio.

•By the Bluetooth technology, you can enjoy clear sound without wire connections.

• Use your favorite music or a beep tone as an alarm. When the set time arrives, the music you select is played at the volume

that you specify, giving you the ideal start to your day (IntelliAlarm function).

• You can easily store and recall of your favorite radio stations, up to 30 FM and 30 DAB stations (DAB function is only for

MCR-B043D).

• Bass, middle, and treble can be adjusted to your taste.

 About this manual

• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will

focus on operation using the remote control.

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

 How to use the remote control  Installing batteries in the remote control

Features

Supplied accessories

Batteries (x 2)

(AAA, R03, UM-4)

FM antenna

(for MCR-B043)

Remote control Speaker cable

(1.5 m (4.9') x 2)

DAB/FM antenna

(for MCR-B043D)

Within 6 m (20')

Check the “+” and “-” of the

batteries and insert them the

correct way around.

(at the end of this manual)

Additional information............................................i

2 En

1 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (☞ P. 5).

2 USB port

Connect your USB device here (

☞

P. 5, 8).

3 (Headphone jack)

Connect headphones here.

4 SOURCE

Switch the audio source to be played.

Pressing this repeatedly will change the selection in the

following order.

CD USB

DAB* FM BT AUX

*MCR-B043D only

5 VOLUME knob

Adjust the volume.

6 Audio control buttons

Use these to operate the CD/USB device.

7 PRESET /

Use these buttons to select a radio station that you’ve

stored (☞ P. 16, 17).

8 Front panel display

The clock and other information is displayed here.

9 Disc slot

Insert a CD here ( ☞ P. 7).

0 (Eject button)

Eject the CD (cannot be operated while the option menu

(☞ P. 18) is displayed).

1 Alarm time

Indicates the alarm time (☞ P. 20).

2 Repeat/shuffle indicator

Displays the playback mode (☞ P. 8).

3 Secondary indicator (MCR-B043D only)

Turns on if a secondary station is playing when you

listen to a DAB station.

4 Multi-function indicator

Displays various information, including the clock time,

information about the currently-playing track, and the

frequency of the radio station.

5 Remote control signal receiver

Make sure that this sensor is not obstructed (☞ P. 1).

6 Alarm indicator

Turns on if the alarm has been set (☞ P. 20).

7 Sleep indicator

Turns on if the sleep timer has been set (☞ P. 19).

NAMES OF PARTS AND THEIR FUNCTIONS

Front panel

:

1 2 3 4 56 7

8

9

: Play/Pause

: Stop

/ :

Skip, Search backward/forward (press and hold

down)

Front panel display

~~~~~~

541 23

6 7

3 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

1 Remote control signal transmitter

2 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (☞ P. 5).

3 SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(☞ P. 19, 21).

4 ALARM

Switch the alarm on/off (☞ P. 21).

5 Source buttons

Switch the audio source to be played. If you press one of

these while the unit is in standby (except ECO standby),

the unit will automatically turn on.

(MCR-B043D only) When listening to the radio, press

RADIO to switch between DAB/FM.

6 OPTION

Display the option menu (☞ P. 18).

7 Item selection buttons

FOLDER /: Switch the playback folder and select

items or edit numerical values when

playing music on data CDs or USB

devices.

ENTER: Confirm a selected item or value.

8 Audio control buttons

Use these to operate the CD/USB device.

9 (Repeat)/ (Shuffle)

Play music on a CD or USB device in repeat/shuffle

mode (☞ P. 8).

0 TUNING /

Tune the radio (☞ P. 15, 16).

A PRESET /

Select a radio station that you stored (☞ P. 16, 17).

B MEMORY

Store a radio station (☞ P. 16).

C +10

Skip ten songs ahead of the currently-playing song.

When playing a data CD or a USB device, this button

skips ten songs within the current folder.

D DISPLAY

Switch the information shown in the front panel display

(☞ P. 7, 8, 15).

E VOLUME +/–

Adjust the volume.

F MUTE

Mute or unmute the sound.

Remote control

3

4

5

8

9

:

A

B

1

7

2

D

C

F

6

E

: Stop

: Play/Pause

/ :

Skip, Search backward/forward (press and hold

down)

4 En

Connect the speakers and antenna.

Do not connect this unit’s power cable until you’ve finished connecting all cables.

If the radio reception is poor, try changing the height or direction or placement of the antenna to find a location that has better

reception.

If you use a commercially available outdoor antenna instead of the supplied antenna, reception may be better.

CONNECTIONS

Connecting the speakers and antenna

ANTENNA SPEAKERS

AUX IN

FM

Speakers

• You must peel off the insulation (covering) from the tip of the speaker cable to

expose the conductor.

• Check the connections; make sure that left and right (L, R) and polarity (red: +,

black: –) are connected correctly. If connections are incorrect, the sound will be

unnatural and the low frequencies may be insufficient. There might not be any

sound at all if connections are incorrect.

• Take care that the conductors of the speaker cable do not touch each other, and that

the conductors do not touch any other metal part. Such conditions can damage this

unit or the speakers.

• Use only the supplied speakers. Using other speakers may result in unnatural sound.

• If you’re using this unit nearby a CRT display and you notice distorted color or

noise in the display, move the speakers farther away from the display.

Twist the bare wires

tightly so the individual

strands are not splayed.

Supplied antenna

Be sure to stretch out the antenna.

To the AC

wall outlet

(MCR-B043)

5 En

CONNECTIONS

English

When you’ve completed all connections, connect this unit’s power cable to an AC outlet.

 USB device

Connect your USB device to the USB port on the front panel. For details on playable files, refer to “NOTES ON DISCS AND

USB DEVICES” (☞ P. 25).

 External devices

Using a commercially available 3.5 mm mini-plug cable, connect your external device to the AUX jack on the rear panel of

this unit.

This unit has the following two types of standby state. Select the mode in POWER SAVING settings menu (☞ P. 18).

* Default setting

Connecting the power cable

Other connections

About the standby state

Mode

Setting menu

(POWER

SAVING)

Clock display

Bluetooth

connection

Charging of USB

devices

Alarm setting

ECO standby

*

(power saving mode)

ECO No clock display Disable Disable Disable

Standby NORMAL Show Enable Enable Enable

Rear panel

The USB device is automatically charged when this unit is on or in standby.

• Stop playback before disconnecting the USB device.

• Charging may not be possible depending on the USB device.

AUX IN

Rear panel

6 En

You’ll use the option menu (☞ P. 18) to set this unit’s date and time.

ADJUSTING THE CLOCK (OPTION MENU)

1 Press to turn the unit on.

2 Press OPTION.

The option menu will appear.

3 Press  / to select “CLOCK SET,” and then

press ENTER.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

4 Set the date and time.

Press ▲/▼ to edit each numerical value, and then press

ENTER to confirm the setting.

Set the items in the order of year month day

hour minute.

When clock setting has finished, the display will indicate

“Completed!”

The clock will be set to 0 second the moment you

complete the clock settings.

• While making these settings, you can press DISPLAY to

select the time format (12-hour / 24-hour).

• If you decide to cancel without changing the setting, press

OPTION before confirming the change.

The time settings will be reset if the unit remains unpowered for

about one hour.

26

Apr

Jan Feb Mar Apr May Jun

January February March April May June

Jul Aug Sep Oct Nov Dec

July August September October November December

2

43

15:30

CD

Display (24-hour) when the unit is on

Display (24-hour) when the unit is off (standby)

*

Clock display

1

* In ECO standby, the clock display will disappear.

7 En

English

 Skipping folders (remote control only)

 Display information (remote control only)

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played is stopped, the track that you listened will start playback from the beginning of the

track the next time you play.

• If you press while playback is stopped, tracks will play as follows the next time playback begins:

 Audio CD: Play from the first track of the CD.



Data CD*/USB device:

Play from the first track of the folder contains the track you listened to last time.

• This unit automatically turns off (standby) if no operation has been performed for 20 minutes after CD/USB device

playback is stopped.

* “Data CD” is a CD that contains MP3/WMA files.

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 25).

Listening to a CD

1 Press the CD source button to switch the

audio source to CD.

If a CD is already inserted, playback will start.

2 Insert a CD into the disc slot.

Playback starts automatically.

Playback can be controlled with either the remote

control, or the front panel on this unit (☞ P. 2, 3).

Insert the CD with the label side facing upward.

Folders and files on a data CD are played in alphabetical order.

While a data CD is playing, you can use the remote control’s

FOLDER ▲/▼ buttons to select the folder.

The folder number (only for a data CD) or the song/file

number is shown for several seconds when starting playback

or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order.

- Elapsed song playback time

- Remaining song playback time (only for an audio CD)

- Song name*

- Album name*

- Artist name*

- File name (only for a data CD)

- Folder name (only for a data CD)

* Shown only if this data is included in the song.

1

2

LISTENING TO CD AND USB DEVICES

8 En

 Skipping folders (remote control only)

 Display information (remote control only)

The playback status is shown by the repeat/shuffle indicator in the front panel display.

Repeat playback Shuffle playback

Listening to a USB device

1 Press the USB source button to switch the

audio source to USB.

If a USB device is already connected, playback will start.

2 Connect a USB device to the USB port.

Playback starts automatically.

Playback can be controlled with either the remote control,

or the front panel on this unit (

☞

P. 2, 3).

Folders and files will play in the order in which they were written.

Stop playback before disconnecting the USB device.

While a USB device is playing, you can use the remote

control’s FOLDER ▲/▼ buttons to select the folder.

The folder/file number is shown for several seconds when

starting playback or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order

.

- Elapsed song playback time

- Song name*

- Album name*

- Artist name*

- File name

- Folder name

* Shown only if this data is included in the song.

Using repeat/shuffle playback (remote control only)

1

2

Press (repeat) repeatedly to

select one of the following

playback modes.

No display: Repeat mode off

: 1 track

: All tracks within the folder (data CD/USB device

only)

: All tracks

Press (shuffle) repeatedly to

select one of the following

playback modes.

No display: Shuffle mode off

: All tracks within the folder (data CD/USB device

only)

: All tracks

9 En

English

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth component (mobile

phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth component.

You’ll need to perform the pairing operation the first time you use your Bluetooth component with this unit, or if the pairing

settings have been deleted. Pairing is an operation that registers the communicating component (subsequently called “the

other component”) with this unit. Once pairing has been completed, subsequent reconnection will be easy even after the

Bluetooth connection is disconnected (☞ P. 10). If pairing is not successful, refer to the item “Bluetooth” in

“TROUBLESHOOTING” (☞ P. 23).

Yamaha does not guarantee all connections between this unit and Bluetooth component.

• This unit can be paired with up to 4 other components. When pairing with the fifth component has succeeded, pairing data for the

component with the oldest connection date will be deleted.

• While connecting to the Bluetooth component and perform the pairing with another component, the current Bluetooth connection will be

canceled.

LISTENING TO MUSIC FROM YOUR

Bluetooth

COMPONENT

Playing back from your Bluetooth component

1 Press the source button for more than 2

seconds to enter pairing mode.

• Pairing mode lasts for 5 minutes.

• In pairing mode, the front panel display of this unit will

indicate “BT Pairing...”.

You can also enter pairing mode by holding down SOURCE on

this unit.

2 Perform Bluetooth pairing on the other

component.

For details refer to the owner’s manual of the other

component.

3 From the Bluetooth connection list of the other

component, choose this unit (MCR-B043

Yamaha or MCR-B043D Yamaha).

When pairing has been completed, the front panel display

of this unit will indicate “BT Pairing OK”.

If you are asked to enter a password, enter the numerals “0000”.

4 Connect this unit and your other component

via Bluetooth.

5 Play back music from your Bluetooth

component.

Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the other component.

• If you connect via Bluetooth from your other component while

this unit is in standby (except ECO standby), this unit will

automatically turn on.

• If you disconnect the Bluetooth connection from your other

component while the audio source is set to Bluetooth, this unit

will automatically turn off (standby).

• If Bluetooth is selected as the audio source, this unit will

automatically turn off (standby) when 20 minutes have elapsed

without any Bluetooth connection nor any operation performed.

1

15:30



BT

Pairing OK

3

LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT

10 En

Once pairing has been completed, connecting a Bluetooth will be easy the next time.

 Connecting from this unit

 Connecting from the other component

If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be

disconnected.

• Switch the audio source other than Bluetooth.

• Turn the unit off.

• Turn off the Bluetooth setting of the other component.

Connecting an already-paired component via Bluetooth

Press the source button to switch the audio

source to Bluetooth.

The Bluetooth indicator will blink in the front panel display;

this unit will search for the other component that was most

recently connected via Bluetooth, and will then establish a

connection (You must first turn on the Bluetooth setting of

the other component).

When the Bluetooth connection has been established, the

Bluetooth indicator will light, and the name of the other

component will be displayed.

1 In the Bluetooth settings of the other component, turn Bluetooth on.

2

From the

Bluetooth

connection list of the other component, choose this unit (MCR-B043 Yamaha or

MCR-B043D Yamaha).

The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the other

component.

Bluetooth

connections cannot be established from the other component when this unit is in ECO standby (

☞

P. 5).

Disconnecting a Bluetooth connection

15:30



15:30



BT

_____

11 En

English

DAB (Digital Audio Broadcasting) and DAB

+

use digital signals for clearer sound and more stable reception compared to

analog signals.

DAB

+

is based on the original DAB standard but uses a more efficient audio codec.

DAB and DAB

+

are broadcast in blocks of data called “ensembles” containing up to several radio stations that are

simultaneously broadcast.

DAB and DAB

+

can also include an extensive amount of text information, enabling you to select a station by name.

Other information, such as the ensemble name or the status of the digital signal, can be displayed on the front panel display.

“DAB” described in this manual may also refer to “DAB

+

”.

Before tuning into DAB stations, an initial scan must be performed. When you select the DAB for the first time, the initial

scan is performed automatically.

To listen to a DAB station, connect the antenna as described in “Connecting the speakers and antenna” (☞ P. 4).

 Performing the initial scan again (Option menu)

LISTENING TO DAB STATIONS (MCR-B043D only)

Preparing for DAB reception

Press the RADIO source button to switch the

audio source to DAB.

The initial scan starts. During the scan, the degree of

progress is displayed on the front panel display.

When scan is completed, the number of receivable DAB

stations appear on the front panel display.

If the initial scan is performed, stored DAB station information

and preset DAB stations are cleared.

1 Press OPTION.

The option menu will appear.

2 Press  / to select DAB INIT SCAN, and

then press ENTER.

The display will indicate “Press ENTER”.

3 Press ENTER.

The initial scan starts.

3

2

1

LISTENING TO DAB STATIONS (MCR-B043D only)

12 En

 Display information (remote control only)

 DAB frequency information

This unit can receive Band III only.

Selecting DAB stations

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press TUNING / to select the DAB

station.

While receiving DAB, DAB station information is

shown on the front panel display.

If the unit does not receive a DAB signal, “Off Air” is

displayed instead of the DAB station name.

1 Secondary indicator:

Some stations have sub (secondary) stations.

If a secondary station is playing, the secondary

indicator is displayed.

2 Signal strength indicator:

Shows current signal strength.

3 Preset number

4 DAB station name

If you press DISPLAY on the remote control, the

information shown on the front panel display will be

switched in the following order.

- STATION LABEL, PRESET NUMBER

- DLS (Dynamic Label Segment)

- ENSEMBLE LABEL

- CHANNEL/FREQ (Channel label and frequency)

- SIGNAL QUALITY

- AUDIO FORMAT (Audio format, DRC)

Frequency Channel label Frequency Channel label Frequency Channel label

174.928 5A 197.648 8B 220.352 11C

176.640 5B 199.360 8C 222.064 11D

178.352 5C 201.072 8D 223.936 12A

180.064 5D 202.928 9A 225.648 12B

181.936 6A 204.640 9B 227.360 12C

183.648 6B 206.352 9C 229.072 12D

185.360 6C 208.064 9D 230.784 13A

187.072 6D 209.936 10A 232.496 13B

188.928 7A 211.648 10B 234.208 13C

190.640 7B 213.360 10C 235.776 13D

192.352 7C 215.072 10D 237.488 13E

194.064 7D 216.928 11A 239.200 13F

195.936 8A 218.640 11B

1

2

10:30

DAB01STATION1

1 2

43

13 En

LISTENING TO DAB STATIONS (MCR-B043D only)

English

Use the preset function to store your favorite 30 stations.

 Deleting a stored preset (Option menu)

Presetting DAB stations (remote control only)

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press TUNING / to select a station that

you want to preset.

3 Press MEMORY.

The display will indicate “PRESET MEMORY,” and

the preset number will blink.

4 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already

been stored, it will be overwritten by the new station.

5 Press MEMORY.

This stores the DAB station.

When presetting has finished, the display will indicate

“Completed!”.

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press OPTION.

The option menu will appear.

3 Press / to select PRESET DELETE, and

then press ENTER.

4 Press  / to select the preset number that

you want to delete.

If you want to cancel the deleting, press OPTION.

5 Press ENTER to complete the operation.

When deleting has finished, the display will indicate

“Deleted!”.

6 Press OPTION to exit the option menu.

4

2

53

1

4

5

3

1

62

10:30

DAB01STATION1

LISTENING TO DAB STATIONS (MCR-B043D only)

14 En

Selecting preset DAB stations

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press PRESET / to select the DAB

station that you want to hear.

You can only select presets that have been stored.

Checking the signal strength of DAB stations (Option menu)

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press OPTION.

The option menu will appear.

3 Press  / to select TUNE AID, and then

press ENTER.

4 Press  / to select the DAB station.

The signal strength will appear.

5 Press OPTION to exit the option menu.

1

2

43

1

52

15 En

English

To listen to the FM station, connect the antenna as described in “Connecting the speakers and antenna” (☞ P. 4).

 Display information (remote control only)

If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the

following order.

LISTENING TO FM STATIONS

Selecting an FM station

1 Press the RADIO source button to switch the

audio source to FM.

2 Tune FM stations

Automatic tuning: Press and hold TUNING /.

Manual tuning: Press TUNING / repeatedly.

If you tune to a station manually while receiving FM, the sound

will be monaural.

Preset number and frequency

Reception status*

* Example of reception status indication.

TUNED/STEREO: A strong FM stereo broadcast is

being received.

TUNED/MONO: A monaural FM broadcast is being

received (even if the FM broadcast is

stereo, reception will be monaural if

the signal is weak).

Not TUNED: No broadcast is being received.

Displaying Radio Data System information

If you press DISPLAY on the remote control while Radio

Data System information is being received, the information

shown on the front panel display will be switched in the

following order.

- PS (Program Service)

- PTY (Program Type)

-RT (Radio Text)

-CT (Clock Time)

- Reception status

- Preset number and frequency

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text) information

uses a lot of bandwidth, so it may be less available compared to

other types of information.

1

2

LISTENING TO FM STATIONS

16 En

Use the preset function to store your favorite 30 stations.

First, press the RADIO source button to switch the audio source to FM.

 Auto preset

This method tunes automatically, and automatically presets only the stations that have good reception.

 Manual preset

 Deleting a stored preset (Option menu)

Presetting FM stations (remote control only)

1 Press and hold down MEMORY.

“AUTO PRESET” will appear and “Press MEMORY”

will blink.

2 Press MEMORY.

Auto preset will begin.

When presetting has finished, the display will indicate

“Completed!”.

When you perform auto preset, all stored stations are cleared

and the new stations are stored.

If you want to stop auto preset before it is completed, press .

1 Press TUNING / to tune a station that

you want to preset.

2 Press MEMORY.

The display will indicate “PRESET MEMORY,” and the

preset number will blink.

3 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already

been stored, it will be overwritten by the new station.

4 Press MEMORY.

When presetting has finished, the display will indicate

“Completed!”.

1 Press OPTION.

The option menu will appear.

2 Press / to select PRESET DELETE, and

then press ENTER.

3 Press / to select the preset number that

you want to delete.

If you want to cancel the deleting, press OPTION.

4 Press ENTER to complete the operation.

When deleting has finished, the display will indicate

“Deleted!”.

5 Press OPTION to exit the option menu.

AUTO PRESET



Press MEMORY

1 2

PRESETMEMORY

FM0187.50MHz

3

1

42

1 5

3 42

17 En

LISTENING TO FM STATIONS

English

Selecting preset FM stations

1 Press the RADIO source button to switch the

audio source to FM.

2 Press PRESET / to select the FM station

that you want to hear.

You can only select presets that have been stored.

LISTENING TO EXTERNAL SOURCES

1 Using a commercially available 3.5 mm mini-

plug cable, connect your external device to the

AUX jack on the rear panel of this unit.

• Turn the unit off before connecting the audio cable.

• Turn down the volume of the unit and your external audio

device before connection.

2 Press to turn the unit on.

3 Press the AUX source button to switch the

audio source to AUX.

4 Start playback on the connected external

audio device.

1

2

AUX IN

1

2

Rear panel

3

18 En

When you press

OPTION

, the option menu will appear in the front panel display, allowing you to make the following settings.

(eject button) cannot be operated while the option menu is displayed.

*1

MCR-B043D only

*2

Default setting

 Procedure for settings

USEFUL FUNCTIONS

Using the Option menu

Option menu Setting or range See page

PRESET DELETE

Deletes a stored preset (shown only if the audio source is DAB

*1

/FM).

13, 16

DAB INIT SCAN

*1

Performs the initial scan (shown only if the audio source is DAB).

11

DAB TUNE AID

*1

Checks the signal strength of DAB station (shown only if the audio source is DAB).

14

DIMMER

Adjusts the brightness of the front panel display (1

*2

: bright, 2: medium, 3: dim).

–

EQ LOW

Adjusts the tonal character (low frequencies) (–10 - 0

*2

- +10 dB).

–

EQ MID

Adjusts the tonal character (mid frequencies) (–10 - 0

*2

- +10 dB).

–

EQ HIGH

Adjusts the tonal character (high frequencies) (–10 - 0

*2

- +10 dB).

–

BALANCE

Adjusts the volume balance of the left and right speakers (L+10 - CENTER

*2

- R+10).

–

POWER SAVING Switches the standby state, NORMAL or ECO (power saving mode)

5

AUTO PWR

STDBY

You can specify the time after which the unit will turn off (standby) automatically.

If no operation occurs for the duration you specify, the unit will turn off (standby) automatically

(

TIME 12H

: 12 hours,

TIME 8H

*2

: 8 hours,

TIME 4H

: 4 hours,

TIME 2H

: 2 hours,

OFF

: the unit

will not turn off (standby)).

–

CLOCK SET Sets the date and time.

6

ALARM SET Sets the alarm.

20

BLUETOOTH

Connects this unit and your component via Bluetooth (ON

*2

: enable, OFF: disable).

9

1 Press OPTION.

The option menu will appear.

2 Press / to select the menu item that you

want to set, and then press ENTER.

3 Press / to edit the setting, and then press

ENTER to confirm the setting.

If you want to continue making other settings, repeat the

procedure from step .

4 Press OPTION to exit the option menu.

If you decide to cancel without changing the setting, press

OPTION before confirming the change.

1

3

4

2

Sivu latautuu ...

Yamaha MCR-B043 White Ohjekirja

Yamaha MCR-B043 White Ohjekirja

muilla kielillä

Liittyvät paperit

Muut asiakirjat