Yamaha RX-V461 - AV Receiver Ohjekirja

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

Printed in China WJ63930

RX-V461

AV Receiver

OWNER’S MANUAL

U

RX-V461_U-cv.fm Page 1 Thursday, December 14, 2006 1:24 PM

IMPORTANT SAFETY INSTRUCTIONS

Caution-i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to

overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

Important safety instructions

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Important safety instructions

Caution-ii En

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna

or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found

in the users manual, may cause interference harmful to the

operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

Caution-iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set this unit

in the standby mode, and disconnect the AC power plug from

the wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet.

Voltages are 110–120/220–240 V AC, 50/60 Hz.

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet, even

if this unit itself is turned off by STANDBY/ON. This

state is called the standby mode. In this state, this unit

is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de

la prise et pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à

la norme NMB-003 du Canada.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

1 En

English

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

Features ................................................................... 2

Getting started ........................................................ 3

Quick start guide .................................................... 4

Preparation: Check the items ..................................... 4

Step 1: Set up your speakers ...................................... 5

Step 2: Connect your DVD player

and other components............................................ 6

Step 3: Turn on the power

and press SCENE 1 button .................................... 8

What do you want to do with this unit? ..................... 9

Connections ........................................................... 10

Rear panel ................................................................ 10

Placing speakers....................................................... 11

Connecting speakers ................................................ 12

Setting the speaker impedance

(U.S.A. and Canada models only) ....................... 13

Information on jacks and cable plugs ...................... 14

Connecting video components................................. 15

Connecting audio components................................. 17

Connecting a Yamaha iPod universal dock ............. 18

Using the VIDEO AUX jacks on the front panel .... 18

Connecting the FM and AM antennas ..................... 19

Connecting the power cable..................................... 19

Turning on and off the power .................................. 19

Front panel display .................................................. 20

Optimizing the speaker setting

for your listening room .................................... 22

Using AUTO SETUP .............................................. 22

Selecting the SCENE templates........................... 26

Selecting the desired SCENE template.................... 26

Creating your original SCENE templates................ 29

Playback ................................................................ 30

Basic operations....................................................... 30

Additional operations............................................... 31

Sound field programs ........................................... 35

Sound field program descriptions ............................ 35

FM/AM tuning ...................................................... 38

Automatic tuning ..................................................... 38

Manual tuning .......................................................... 38

Automatic preset tuning........................................... 39

Manual preset tuning ............................................... 39

Selecting preset stations........................................... 40

Exchanging preset station ........................................ 40

XM Satellite Radio tuning ................................... 41

Connecting the XM Mini-Tuner Dock .................... 41

Activating XM Satellite Radio ................................ 42

Basic XM Satellite Radio operations....................... 42

Setting XM Satellite Radio preset channels ............ 44

Displaying the XM Satellite Radio information...... 45

Using iPod™.......................................................... 46

Controlling iPod™................................................... 46

Recording .............................................................. 48

SET MENU ............................................................49

Using SET MENU ................................................... 50

1 SOUND MENU.................................................... 51

2 INPUT MENU...................................................... 55

3 OPTION MENU................................................... 57

Remote control features........................................59

Using remote control on the SCENE feature........... 59

Controlling this unit, a TV, or other components.... 60

Setting remote control codes ................................... 62

Resetting all remote control codes........................... 63

Advanced setup......................................................64

Troubleshooting.....................................................65

Glossary..................................................................72

Specifications .........................................................74

Index .......................................................................75

(at the end of this manual)

Front panel................................................................i

Remote control ....................................................... ii

List of remote control codes ................................. iii

3

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the

buttons on the front panel or the ones on the remote control.

In case the button names differ between the front panel and

the remote control, the button name on the remote control is

given in parentheses.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and product, the product has priority.

•“

9

SPEAKERS” or “

A

DVD” (example) indicates the

name of the parts on the front panel or the remote control.

Refer to the attached sheet or the top pages of this manual

for the information about each position of the parts.

•The symbol “☞ ” with page number(s) indicates the

corresponding reference page(s).

Features

2 En

Built-in 5-channel power amplifier

◆ Minimum RMS output power

[U.S.A. and Canada models]

(1 kHz, 0.9% THD, 8 Ω)

Front: 100 W + 100 W

Center: 100 W

Surround: 100 W + 100 W

[Other models]

(1 kHz, 0.9% THD, 6 Ω)

Front: 100 W + 100 W

Center: 100 W

Surround: 100 W + 100 W

SCENE select function

◆ Preset SCENE templates for various situations

◆ SCENE template customizing capability

Decoders and DSP circuits

◆ Proprietary Yamaha technology for the creation of multi-

channel surround sound

◆ Compressed Music Enhancer mode to improve the sound

quality of compression artifacts (such as the MP3 format) to

that of a high-quality stereo

◆ Dolby Digital decoder

◆ Dolby Pro Logic/Dolby Pro Logic II decoder

◆ DTS decoder

◆ Neural Surround decoder

(U.S.A. and Canada models only)

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated FM/AM tuner

◆ 40-station random and direct preset tuning

◆ Automatic preset tuning

XM Satellite Radio

(U.S.A. and Canada models only)

◆ XM Satellite Radio tuning capability (using the “XM Mini-

Tuner Dock” sold separately)

◆ Neural Surround decoder to play back the XM HD content of

XM Satellite Radio broadcasts in multi-channels, resulting in

a full surround sound experience

iPod controlling capability

◆ DOCK terminal to connect a Yamaha iPod universal dock

(YDS-10, sold separately), which supports iPod (Click and

Wheel), iPod nano, and iPod mini

◆ Playback information displaying capability

◆ Battery charging capability

Other features

◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for

automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ Direct Stereo mode for pure hi-fi stereo sound for analog and

PCM 2-channel sources

◆ 6 additional input jacks for discrete multi-channel input

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ Component video input/output capability

(3 COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ S-video signal input/output capability

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Cinema and music night listening modes

◆ Remote control with preset remote control codes

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“SILENT CINEMA” is a trademark of YAMAHA

CORPORATION.

“iPod” is a trademark of Apple Computer, Inc., registered in the

U.S. and other countries.

“DTS” and “DTS Digital Surround” are registered trademarks of

DTS, Inc.

The XM name and related logos are registered trademarks of XM

Satellite Radio Inc.

Neural Surround

™

name and related logos are trademarks owned

by Neural Audio Corporation.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YA M A H A and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

Features

iPod

TM

Getting started

3 En

English

INTRODUCTION

■ Checking the supplied accessories

Check that you received all of the following parts.

The form of the supplied accessories varies depending on the

models.

■ VOLTAGE SELECTOR

(Asia and General models only)

Select the switch position (upper or lower)

according to your local voltage using a straight

slot screwdriver.

Voltages are 110-120/220-240 V AC, 50/60 Hz.

■ Installing batteries in the remote control

1 Take off the battery compartment cover.

2 Insert the two supplied batteries

(AA, R6, UM-3) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice the following

conditions:

– the operation range of the remote control decreases.

– the TRANSMIT indicator does not flash or its light becomes

dim.

• Do not use an old battery and a new one together.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries and set up the remote control

code.

Getting started

Note

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

5678

90

+10

ENT

1234

MENU

TITLE

SET MENU

LEVEL

MUSIC

MOVIEENTERTAIN STEREO

ENHANCER

STRAIGHT

DIRECT ST.

SUR. DECODE

NIGHT

SLEEP

DISPLAY

RETURN

BAND

SRCH MODE

XM MEMORY

REC

SCENE

A-E/CAT.

ENTER

PRESET/CH

VOLUME

TV VOL

TV CH

TV MUTE

TV INPUT

MUTE

AMP

SOURCE

TV

CD

CD-R

DVD

DTV

MD

MULTI CH IN

AUDIO SEL

CBL

TUNER

V-AUX

DOCK

DVR

XM

STANDBY

POWER

AV

TV

TRANSMIT

CODE SET

1

2 34

Remote control

Batteries (2)

(AA, R06, UM-3)

Indoor FM antenna

AM loop antenna

Optimizer

microphone

110V-

120V

220V-

240V

VOLTAGE

SELECTOR

Notes

1

3

2

Quick start guide

4 En

The following steps describe the easiest way to enjoy

DVD movie playback in your home theater.

In these steps, you need the following supplied

accessories.

❏ Indoor FM antenna

❏ AM loop antenna

The following items are not included in the package of this

unit.

❏ Speakers

❏ Front speakers ...................................... 2

❏ Center speaker ...................................... 1

❏ Surround speakers ............................... 2

Select magnetically shielded speakers. The

minimum required speakers are two front speakers.

❏ Active subwoofer ...................................... 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cables .......................................... 5

❏ Subwoofer cable ........................................ 1

Select a monaural RCA cable.

❏ DVD player ................................................. 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output

jack.

❏ Video monitor ............................................. 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ................................................ 1

Select an RCA composite video cable.

❏ Digital coaxial audio cable ....................... 1

Quick start guide

Front right

speaker

Subwoofer

Surround left

speaker

Front left

speaker

Surround right

speaker

Center speaker

DVD player

Video monitor

Enjoy DVD playback!

Step 1: Set up your speakers

Step 2: Connect your DVD player

and other components

Step 3: Turn on the power and

press SCENE 1 button

☞

P. 6

☞

P. 8

☞

P. 5

Preparation: Check the items

Quick start guide

5 En

English

INTRODUCTION

Place your speakers in the room and connect them to this

unit.

1 Place your speakers and subwoofer in the

room.

2 Connect speaker cables to each speaker.

Cables are colored or shaped differently, perhaps with

a stripe, groove or ridge. Connect the striped

(grooved, etc.) cable to the “+” (red) terminals of

your speaker. Connect the plain cable to the “–”

(black) terminals.

3 Connect each speaker cable to the

corresponding speaker terminal of this unit.

1 Make sure that this unit and the subwoofer are

unplugged from the AC wall outlets.

2 Twist the exposed wires of the speaker cables

together to prevent short circuits.

3 Do not let the bare speaker wires touch each other.

4 Do not let the bare speaker wires touch any metal

part of this unit.

Be sure to connect the left channel (L), right channel

(R), “+” (red) and “–” (black) properly.

Front speakers

Center and surround speakers

4 Connect the subwoofer cable to the input

jack of the subwoofer and the SUBWOOFER

OUTPUT jack of this unit.

Step 1: Set up your speakers

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

ANTENNA

SPEAKERS AC OUTLETS

LR LR

SURROUND CENTER FRONT B

AUDIO OUTPUT

L

1

2

3

R

L

R

L

R

DVD

DTV/CBL

D

V

R

CD

SUB

WO

O

FER

IN

OU

T

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

S VIDEO

VIDEO

DVR

AM

FRONT A

GND

FM

UNBAL.

75

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

MD/

CD-R

OU

T

(

REC)

IN

(PLAY)

12 3 4

To the front

right speaker

Front left speaker

Loosen Insert Tighten

To the

surround

right speaker

To the surround

left speaker

To the center

speaker

OUTPUT

SUB

WOOFER

IN

(PLAY)

OUT

(REC)

MD/

CD-R

SUBWOOFER

OUTPUT jack

Subwoofer cable

Input jack

AV receiver

Subwoofer

Quick start guide

6 En

1 Connect the digital coaxial audio cable to the

digital coaxial audio output jack of your DVD

player and the DVD DIGITAL INPUT COAXIAL

jack of this unit.

2 Connect the video cable to the composite

video output jack of your DVD player and the

DVD VIDEO jack of this unit.

3 Connect the video cable to the video input

jack of your video monitor and the VIDEO

MONITOR OUT jack of this unit.

Step 2: Connect your DVD player

and other components

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

ANTENNA

SPEAKERS AC OUTLETS

LR LR

SURROUND CENTER FRONT B

AUDIO OUTPUT

L

1

2

3

R

L

R

L

R

DVD

DTV/CBL

D

V

R

CD

SUB

WO

O

FER

IN

OU

T

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

S VIDEO

VIDEO

DVR

AM

FRONT A

GND

FM

UNBAL.

75

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

MD/

CD-R

OU

T

(REC)

IN

(PLAY)

Make sure that this unit and the DVD

player are unplugged from the AC wall

outlets.

Digital coaxial

audio output jack

Digital coaxial audio

cable

DVD DIGITAL INPUT

COAXIAL jack

DVD player

AV receiver

Composite video

output jack

Video cable

DVD VIDEO jack

DVD player

AV receiver

L/MONO

AUDIO AUDIO

COLOR STREAM HD

VIDEO

VIDEO-1 IN IN

S-VIDEO

RYP

B

P

R

RL/MONO

Video monitor

AV receiver

Video input jack

VIDEO MONITOR OUT

jack

Video cable

Quick start guide

7 En

English

INTRODUCTION

4 Connect the FM and AM antennas to this

unit.

See page 19 for the details.

y

The wire of the AM loop antenna does not have any polarity and

you can connect either end of the wire to AM and GND terminal.

5 Connect the power plug of this unit and other

components into the AC wall outlet.

y

This unit is equipped with AC OUTLET(S) for the power supply

of the other components (except Korea model). See page 19 for

details

Indoor FM antenna

AM loop antenna

Open the lever Insert Close the lever

■ For further connections

• Using the other kind of speaker

combinations

☞ P. 12

• Connecting a video monitor

☞ P. 15, 16

• Connecting a DVD player

☞ P. 15, 16

• Connecting a DVD recorder

☞ P. 15, 16

• Connecting a cable TV or a satellite tuner

☞ P. 15, 16

• Connecting a CD player and an MD

recorder

☞ P. 17

• Connecting a DVD player via analog

multi-channel audio connection

☞ P. 17

• Connecting a Yamaha iPod universal dock

☞ P. 18

• Using the VIDEO AUX jacks on the front

panel

☞ P. 18

• Connecting an outdoor FM/AM antenna

☞ P. 19

• Connecting the XM Mini-Tuner Dock

☞ P. 41

Quick start guide

8 En

1 Turn on the video monitor connected to this

unit.

2 Press

1

STANDBY/ON on the front panel.

3 Press

F

SCENE 1.

“DVD Viewing” appears in the front panel display,

and this unit automatically optimize own status for

the DVD playback.

y

The indicator on the selected SCENE button lights up while

this unit is in the SCENE mode.

4 Start playback of the desired DVD on your

player.

5 Rotate

8

VOLUME to adjust the volume.

When you change the input source or sound field program, the

SCENE mode is deactivated, and the indicator on the selected

SCENE button turns off.

■ Using the other SCENE buttons

In the following cases, try pressing the corresponding

SCENE button to enjoy playback of the desired sources.

Case A: “I want to listen to a music disc from the

connected DVD player as the background

music for this room...”

Press

F

SCENE 2 (or

F

SCENE 2) to select “Disc

Listening”.

Case B: “I want to watch a TV program...”

Press

F

SCENE 3 (or

F

SCENE 3) to select “TV

Viewing”.

To use the “TV Viewing” template (Case B), you must

connect a cable TV or a satellite tuner to this unit in

advance. See page 15 for details.

Step 3: Turn on the power and

press SCENE 1 button

Check the type of the connected speakers.

If the speakers are 6 ohm speakers, set “SP IMP.” to

“6Ω MIN” before using this unit (see page 13).

Note

Quick start guide

9 En

English

INTRODUCTION

Case C: “I want to listen to a music program from

the FM radio station...”

Press

F

SCENE 4 (or

F

SCENE 4) to select “Radio

Listening”.

• To use the “Radio Listening” template (Case C), you must

tune into the desired radio station in advance. See pages 38

to 40 for tuning information.

• To achieve the best possible reception, orient the

connected AM loop antenna, or adjust the position of the

end of the indoor FM antenna.

y

If you cannot find the desired situation, you can select and change

the assigned SCENE template for the SCENE buttons. See

page 26 for details.

■ After using this unit...

Press

1

STANDBY/ON on the front panel to set

this unit to the standby mode.

This unit is set to the standby mode. In the standby mode,

this unit consumes a small amount of power in order to

receive infrared signals from the remote control. To turn

on this unit from the standby mode, press

1

STANDBY/

ON (or GSTANDBY). See page 19 for details.

In the standby mode, this unit consumes a small amount of power

in order to receive infrared signals from the remote control.

Notes

Note

What do you want to do with this

unit?

■ Customizing the SCENE templates

• Using various SCENE templates

☞ P. 26

• Creating your original SCENE templates

☞ P. 29

■ Using various input sources

• Basic controls of this unit

☞ P. 30

• Enjoying FM/AM radio programs

☞ P. 38

• Enjoying XM Satellite Radio programs

☞ P. 41

• Using your iPod with this unit.

☞ P. 46

■ Using various sound features

• Using various sound field programs

☞ P. 35

• Using the pure direct mode for the high

fidelity sound

☞ P. 32

• Customizing the sound field programs

☞ P. 37

■ Adjusting the parameters of this unit

• Automatically optimizing the speaker

parameters for your listening room (AUTO

SETUP)

☞ P. 22

• Manually adjusting various parameters of

this unit

☞ P. 49

• Setting the remote control

☞ P. 59

• Adjusting the advanced parameters

☞ P. 64

■ Additional features

Automatically turning off this unit

☞ P. 34

Connections

10 En

1 DOCK terminal

See page 18 for connection information.

2 XM jack (U.S.A. and Canada models only)

See page 41 for connection information.

3 COMPONENT VIDEO jacks

See page 16 for connection information.

4 VIDEO jacks

See pages 15 and 16 for connection information.

5 ANTENNA terminals

See page 19 for connection information.

6 SPEAKERS terminals

See page 12 for connection information.

7 AC OUTLET(S)

See page 19 for connection information.

8 DIGITAL INPUT jacks

See pages 15 and 17 for connection information.

9 MULTI CH INPUT jacks

See page 17 for connection information.

0 AUDIO jacks

See pages 15 and 17 for connection information.

A SUBWOOFER OUTPUT jack

See page 12 for connection information.

B VOLTAGE SELECTOR

(Asia and General models only)

See page 3 for details.

Connections

Rear panel

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

ANTENNA

SPEAKERS AC OUTLETS

L

R

L

R

SURROUND CENTER FRONT B

AUDIO OUTPUT

L

1

2

3

R

L

R

L

R

DVD

DT

V

/CBL

D

V

R

C

D

SUB

W

OO

F

E

R

IN

O

UT

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

S VIDEO

VIDEO

DVR

AM

FRONT A

GND

FM

UNBAL.

75

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

M

D/

CD-R

O

UT

(

R

E

C

)

IN

(PLAY)

2

8 9 0 A B

1 3 4 5 6 7

(U.S.A. model)

11 En

Connections

English

PREPARATION

The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-

channel audio sources.

Front left and right speakers (FL and FR)

The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the

ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a

center speaker, you can do without it. Best results, however, are obtained with the full system.

Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround sounds.

Subwoofer (SW)

The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is

effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction

of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is

not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front

speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Placing speakers

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

FR

FL

C

SL

SR

SW

1.8 m (6 ft)

12 En

Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

this unit cannot reproduce the input sources accurately.

A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe,

groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable

to the “–” (black) terminals.

Connecting speakers

Caution

• Before connecting the speakers, make sure that this unit is turned off (see page 19).

• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage

this unit and/or the speakers.

• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the

speakers away from the monitor.

• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 13).

Note

Subwoofer

Center speaker

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

ANTENNA

SPEAKERS AC OUTLETS

L

R

L

R

SURROUND CENTER FRONT B

AUDIO OUTPUT

L

1

2

3

R

L

R

L

R

DT

V

/CBL

D

VR

C

D

SUB

W

OOF

ER

IN

O

UT

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

DVD

S VIDEO

VIDEO

DVR

AM

FRONT A

GND

FM

UNBAL.

75

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

M

D/

CD

-

R

O

UT

(

R

E

C

)

IN

(PLAY)

Subwoofer

Front speakers (A)

LeftRight

Center

speaker

Front speakers (B)

LeftRight

Surround speakers

LeftRight

(U.S.A. model)

13 En

Connections

English

PREPARATION

■ Before connecting to the SPEAKERS

terminal

A speaker cord is actually a pair of insulated cables

running side by side. Cables are colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals of this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

Remove approximately 10 mm (3/8”) of insulation

from the end of each speaker cable and then

twist the bare wires of the cable together to

prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Loosen the knob.

2 Insert the bare end of the speaker wire into

the hole on the terminal.

3 Tighten the knob to secure the wire.

Connecting the banana plug

(except Korea and Asia models)

The banana plug is a single-pole electrical connector

widely used to terminate speaker cables. First, tighten the

knob and then insert the banana plug connector into the

end of the corresponding terminal.

1 Make sure this unit is turned off.

See page 19 for details about turning on or off this

unit.

2 Press and hold

0

TONE CONTROL and

then press

1

STANDBY/ON to turn on this

unit.

This unit turns on, an the advanced setup menu

appears in the front panel display.

3 Press

A

PROGRAM l / h repeatedly to

select “SP IMP.”.

The following display appears in the front panel

display.

4 Press

B

STRAIGHT repeatedly to select “6Ω

MIN”.

The following display appears in the front panel

display.

5 Press

1

STANDBY/ON to confirm your

selection and set this unit to the standby

mode.

The setting you made is reflected next time you turn on this unit.

10 mm (3/8”)

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Setting the speaker impedance

(U.S.A. and Canada models only)

Caution

If you are to use 6 ohm speakers, set “SP IMP.” to “6Ω

MIN” as follows BEFORE using this unit.

Note

SP IMP.- 8 MIN

SP IMP.- 6 MIN

14 En

Connections

■ Audio jacks

This unit has three types of audio jacks. Connection

depends on the availability of audio jacks on your other

components.

AUDIO jacks

For conventional analog audio signals transmitted via left

and right analog audio cables. Connect red plugs to the

right jacks and white plugs to the left jacks.

DIGITAL AUDIO COAXIAL jacks

For digital audio signals transmitted via coaxial digital

audio cables.

DIGITAL AUDIO OPTICAL jacks

For digital audio signals transmitted via optical digital

audio cables.

• You can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. All digital input jacks are compatible with

digital signals with up to 96 kHz of sampling frequency.

• This unit handles digital and analog signals independently. Thus

audio signals input at the digital jacks are not output at the

analog AUDIO OUT (REC) jacks.

• Pull out the cap from the optical jack before you connect the

fiber optic cable. Do not discard the cap. When you are not

using the optical jack, be sure to put the cap back in place. This

cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your video

monitor.

VIDEO jacks

For conventional composite video signals transmitted via

composite video cables.

S VIDEO jacks

For S-video signals, separated into the luminance (Y) and

chrominance (C) video signals transmitted on separate

wires of S-video cables.

COMPONENT VIDEO jacks

For component signals, separated into the luminance (Y)

and chrominance (P

B, PR) video signals transmitted on

separate wires of component video cables.

The OSD signal is not output at the DVR OUT (REC) jacks.

Information on jacks and cable plugs

VIDEO S VIDEO

COMPONENT VIDEO

Y P

B

P

R

PB

Y

P

R

S

V

COAXIAL

DIGITAL AUDIO

AUDIO

OPTICAL

DIGITAL AUDIO

R

L

C

O

R

L

Left and right

analog audio

cable plugs

Optical

digital

audio cable

plug

Coaxial

digital audio

cable plug

Composite

video cable

plug

Component

video cable

plugs

Audio jacks and cable plugs Video jacks and cable plugs

(Red)(White) (Orange) (Yellow) (Green) (Blue) (Red)

S-video

cable plug

Notes

Note

PR

P

B

Y

P

R

P

B

Y

Video signal flow for MONITOR OUT

Output

(MONITOR OUT)

Input

COMPONENT

VIDEO

S VIDEO

15 En

Connections

English

PREPARATION

Connect the video components as follows.

y

You can also connect a video monitor, DVD player, digital TV,

and cable TV to this unit using the S VIDEO or COMPONENT

VIDEO connections (see page 16).

■ Connecting a video monitor and a DVD

player

■ Connecting a cable TV/satellite tuner

and a DVD recorder

Connecting video components

Make sure that this unit and other

components are unplugged from the

AC wall outlets.

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

AUDIO

L

1

2

3

R

L

R

DTV/CBL

D

V

R

CD

IN

OUT

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

DVD

S VIDEO

VIDEO

DVR

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

C

L

R

VV

DVD player

Video monitor

Video in

Video out

Audio out

indicates recommended connections

indicates alternative connections

MULTI CH INPUT

COMPONENT VIDEO

DOCK

DIGITAL INPUT

XM

VIDEO

AUDIO

L

1

3

R

L

R

DTV/CBL

D

V

R

CD

IN

OUT

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

OPTICAL

COAXIAL

CD

DTV/

CBL

DVD

P

R

P

B

Y

DTV/CBL DVR DVD

DVD

S VIDEO

VIDEO

DVR

IN OUT

DTV/CBLMONITOR

OUT

MONITOR

OUT

2

L

R

L

R

L

R

VVV

O

Cable TV or

Satellite tuner

DVD recorder

Audio out

Video out

Audio out

Audio in

Audio out

Video in

Video out

indicates recommended connections

indicates alternative connections

16 En

Connections

■ Connecting to the COMPONENT VIDEO or S VIDEO jacks

You can enjoy high-quality pictures by connecting your video monitor and video source components to this unit using

COMPONENT VIDEO or S VIDEO connections.

Be sure to connect your video components in the same way you connect your video monitor to this unit. For example, if you connect

your video monitor to this unit using a COMPONENT VIDEO connection, connect your video components to this unit using the

COMPONENT VIDEO connection.

COMPONENT VIDEO connection S VIDEO connection

Note

MULTI CH INPUT

COMPONENT VIDEO

L

R

CENTER

SUBWOOFER

SURROUNDFRONT

DVD

P

R

P

B

Y

DTV/CBL DVR MONITOR

OUT

P

R

P

B

Y

P

R

P

B

Y

P

R

P

B

Y

P

R

P

B

Y

DVD player

Video monitor

Video out

Video in

Cable TV or

satellite tuner

DVD recorder

VIDEO

AUDIO

L

R

D

TV

/CB

L

D

VR

C

D

I

N

O

UT

DVD

S VIDEO

VIDEO

DVR

IN OUT

DTV/CBL MONITOR

OUT

S S

S

S S

DVD player

Video monitor

Video out

Video in

Cable TV or

satellite tuner

DVD recorder

Video in

Sivu latautuu ...

Yamaha RX-V461 - AV Receiver Ohjekirja

Tämä käsikirja sopii myös

Yamaha RX-V461 - AV Receiver Ohjekirja

muilla kielillä

Liittyvät paperit

Muut asiakirjat