Yamaha ISX-800 Restio Omistajan opas

INTEGRATED AUDIO SYSTEM

SYSTÈME AUDIO INTÉGRÉ

ISX-800

G

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place

– away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 2.5 cm (1 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot (or vice versa), and do not locate this

unit in an environment with high humidity (i.e., a room

with a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire, damage to

this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the system to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the system off, then leave this unit

alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

– Keep the batteries in a location out of reach of

children. Batteries can be dangerous if a child were to

put in his or her mouth.

– If the batteries grow old, the effective operation range

of the remote control decreases considerably. If this

happens, replace the batteries with two new ones as

soon as possible.

– Do not use old batteries together with new ones.

–

Do not use different types of batteries (such as

alkaline and manganese batteries) together. Read the

packaging carefully as these different types of

batteries may have the same shape and color.

– Exhausted batteries may leak. If the batteries have

leaked, dispose of them immediately. Avoid touching

the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

– If you plan not to use the unit for a long period of

time, remove the batteries from the unit. Otherwise,

the batteries will wear out, possibly resulting in a

leakage of battery liquid that may damage the unit.

– Do not throw away batteries with general house

waste. Dispose of them correctly in accordance with

your local regulations.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

based (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English Français Deutsch Svenska Italiano Español Nederlands Русский

NAMES OF PARTS AND THEIR FUNCTIONS.........................2

ADJUSTING THE CLOCK.........................................................5

LISTENING TO iPod..................................................................6

LISTENING TO CD AND USB DEVICES..................................7

LISTENING TO FM STATIONS...............................................10

LISTENING TO EXTERNAL SOURCES .................................11

USING THE ALARM FUNCTION ............................................12

USING THE SLEEP TIMER.....................................................15

TONE CONTROL.....................................................................15

ADJUST BRIGHTNESS OF FRONT PANEL DISPLAY .........15

TROUBLESHOOTING.............................................................16

NOTES ON DISCS AND USB DEVICES.................................18

SPECIFICATIONS ...................................................................19

• Playback music on external devices such as iPod/iPhone models, audio/data CDs and USB devices, and tune in to the FM.

• Use your favorite music or set of beeps as an alarm. The music you select is played at a volume of your own choice at the set alarm time,

giving you the best possible start to the day (IntelliAlarm function).

• Store/call up to five of your favorite FM stations easily.

• The 3-band equalizer (bass, middle, treble) can be set so that music sounds exactly how you want it.

• Two types of clocks (with hour hands) that match the design of the unit can be shown.

 About this manual

• The phrase “iPod” used throughout this manual also includes the “iPhone”.

• If both the unit and remote control buttons can be used to operate a feature, the manual will describe steps using the buttons on the unit.

Insert the batteries into the remote control in the correct direction

(+ and –).

Point the remote control at the remote control signal receiver (on

the front panel) and use within the range shown below.

CONTENTS

Features

Supplied accessories

How to use the remote control

ISX-800

Power cable Remote control

Dock cover

USB cap

FM antenna

Bracket

Pole

Base

Support

Cable clamp

Screw set

Note

Use these items to assemble the

stand. Read the separate

Assembly Guide for information

on how to assemble the stand.

Note

Keep the USB cap out of

reach of children so as to

ensure that it is not

mistakenly swallowed.

2 x Batteries

(AA, LR6, UM-3)

Owner’s Manual

(this manual)

Assembly Guide

6 m (20')

2 En

a (Power)

Press to turn the system on/off. Time is displayed on the front

panel even when the system is off.

y

• Press and hold on the top of the unit for more than 3 seconds to set

the system to power save mode. No information on the front panel is

displayed in power save mode. This can reduce power consumption.

To cancel power save mode, press again.

• Even in system off/power save mode, the alarm function is available.

b iPod dock

Connect an iPod.

c USB port

Connect a USB device (P. 9).

d VOLUME –/+

Adjust the volume.

e SOURCE

Switch the source to be played.

f ALARM

Turns the alarm on/off, and allows various alarm settings to be

adjusted (P. 13, 14).

g SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(P. 14, 15).

h PRESET

Store/call up FM stations, or switch the playback folder (when

playing music on data CDs or USB devices).

i /

Skip the playback track/file, or tune the radio.

Holding the button down while playing a track/file will search

backward/forward the track/file.

j /

Play/pause the track being played.

k

Eject the CD.

l Disc slot

Insert a CD.

NAMES OF PARTS AND THEIR FUNCTIONS

Top panel

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

iPod

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

12345678 jlk9

 Connecting an iPod to the iPod dock

y

• An iPod will be recharged while it is connected to the dock. The iPod will not be recharged

when the unit is in power save mode.

• Be sure to use a dock adaptor that is compatible with your iPod. If you do not use the adaptor

or the adaptor is not compatible, the connection could be loose or poor, which could cause

damage to the connector. For details on dock adaptor information, please visit official Apple’s

website.

• If an iPod in protective case is connected by force, the connector may be damaged. Remove

the protective case before connection.

• When the iPod is not in use, set the iPod dock cover to protect the connector.

Dock adaptor

3 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

1 Play/shuffle/repeat indicator

Displays the playback mode (P. 6, 9).

b Remote control signal receiver

c Clock indicator

Shows the clock hour hand (P. 5).

d Source indicator

Shows selected source.

e Alarm indicator

Turns on if the alarm has been set (P. 12).

f Sleep indicator

Turns on if the sleep timer has been set (P. 15).

g Multi-function indicator

Displays various information, including the clock time, track

number being played or FM station.

h Illumination sensor

Detects ambient lighting. Do not cover this sensor.

a ALARM TYPE

Switches the alarm type (P. 13).

b CLOCK

Switches the type of clock display or allows the time to be set

(P. 5).

c DIMMER

Adjusts the brightness of the front panel display (P. 15).

d AUX

Connects an external device.

e FM antenna terminal

Connects the supplied FM antenna or outdoor antenna.

Notes

• The antenna should be stretched out. If radio reception is poor, change

the height, direction, or placement of the antenna.

• If you use an outdoor antenna instead of the supplied FM antenna,

reception will be better.

f Terminal cover

Remove the terminal cover before connecting external devices

to AUX, and/or connecting the FM antenna to antenna

terminal.

Front panel display

FM

CD

AUX

USB

iPod

ALL

1

2

1

8

56

7

3

4

Rear panel

1

6

2 3

4

5

Supplied

FM antenna

If you pass the outdoor antenna cable and/or external device cable through the pole of the stand, read the separate Assembly Guide.

NAMES OF PARTS AND THEIR FUNCTIONS

4 En

a Remote control signal transmitter

b (Power)

Press to turn the system on/off.

c ALARM

Switches the alarm on/off.

d SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(P. 14, 15).

e Source button

Switch the source to be played.

f FOLDER

Switch the playback folder when playing music on data CDs or

USB devices.

g /

Skip the playback track/file.

Holding the button down while playing a track/file will search

backward/forward the track/file.

h

Play/pause.

i

Stop playback.

j (Repeat)/ (Shuffle)

Play music on an iPod, audio/data CD or USB device in repeat/

shuffle (P. 6, 9).

k EQ LOW/MID/HIGH

Adjust the bass, middle or treble sound quality (P. 15).

l PRESET /

Select a preset FM station.

m MEMORY

Store the FM station (P. 10).

n TUNING /

Tune the radio.

o VOLUME +/–

Adjust the volume.

p MUTE

Mute/resume the sound.

Remote control

1

n

p

o

4

6

j

k

8

9

5

3

2

m

l

7

 iPod control buttons

5 En

English

1 Move the CLOCK switch on the rear panel to SET.

2 Set the time with / .

3 Move the CLOCK switch on the rear panel to

CLOCK1 or CLOCK2.

y

• Connecting an iPod to the iPod dock in step 2 will copy the time on the

iPod to the unit. If the iPod is already connected to the iPod dock when

CLOCK is set to SET, the time in the iPod will not be copied.

• Pressing SNOOZE/SLEEP in step

2 will switch between the 12 and 24

hour clock display.

Note

The time settings will be reset if the unit is not powered for more than one

week.

Move the CLOCK switch on the rear panel to switch the clock type.

 Clock display mode 1 (CLOCK 1)

 Clock display mode 2 (CLOCK 2)

ADJUSTING THE CLOCK

Setting the time

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

2

Top panel

SET

Rear panel

Set time (flashing)

Switching the clock type

CLOCK 2

CLOCK 1

Rear panel

Eg: 10:50 AM

Analog clock

hour hand

(hour)

Minute

Eg: 10:50 AM

Minute

Hour

6 En

For details on compatible iPod models, refer to “SPECIFICATIONS” (P. 19).

1 Connect an iPod to the iPod dock.

2 Press SOURCE and set iPod as the playback

source.

3 Play the iPod by pressing / .

Playback can be controlled with either the remote control,

iPod or the top panel on this unit.

y

• You can remove the iPod whenever you want.

• If the system is turned off, it will turn on automatically when music/video

on the iPod is played.

Playback

mode can be checked with the indicator on the front panel display.

Notes

• Repeat/shuffle may not operate correctly depending on the type of iPod

used.

• The repeat/shuffle playback order may differ depending on the type of

iPod used.

 Repeat playback

Press REPEAT on the remote control to select a playback mode

from the following.

:One

:All

No display: Off

 Shuffle playback

Press SHUFFLE on the remote control to select a playback mode

from the following.

: Songs

:Albums

No display: Off

LISTENING TO iPod

Playing the iPod

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

23

Top panel

Remote control

Button Function

Top

Panel

/

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

Remote

control

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

FOLDER/

MENU/

ENTER/

iPod menu control

Repeat/shuffle playback

REPEAT

SHUFFLE

Remote control

7 En

English

1 Press SOURCE to set CD as the playback source.

2 Insert the audio CD into the Disc slot with the

label side facing toward the front of the unit.

Playback starts automatically. The track number is shown for a

while when starting playback or skipping tracks.

Use the following buttons to control the unit while playing

back tracks on audio CDs.

Note

CDs cannot be inserted or ejected when the system is in power save

mode (☞ P. 2).

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played back is stopped, the track that was being played back will start playing from the beginning of the

track the next time playback begins.

• If you press on the remote control while playback is stopped, the next time playback begins, the unit will play tracks as follows:

– For audio CD : from the first track of the CD.

– For data CD/USB device: from the first track of the folder that contains the track that was played last.

• The system turns off automatically 60 minutes after CD/USB device playback is stopped.

y

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (P. 18).

Listening to an audio CD

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

12

Top panel

Button Function

Top

Panel

/

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

Eject the CD

Remote

control

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

Stop

CD

Track number

LISTENING TO CD AND USB DEVICES

8 En

1 Press SOURCE to set CD as the playback source.

2 Insert the data CD into the Disc slot with the

label side facing toward the front of the unit.

Playback starts automatically. The folder/file number is shown

for a while when starting playback or skipping tracks.

Use the following buttons to control the unit while playing

back tracks on data CDs.

Listening to a data CD

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

12

Top panel

Button Function

Top

Panel

/

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

PRESET Change the playback folder

Eject the CD

Remote

control

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

Stop

FOLDER Change the playback folder

CD

Folder number

File number

9 En

LISTENING TO CD AND USB DEVICES

English

1 Press SOURCE and set USB as the playback

source.

2 Connect a USB device to the USB port.

Playback starts automatically. The folder/file number is shown

for a while

when starting playback or skipping tracks.

Use the following buttons to control the unit while playing

back tracks on USB devices.

y

You can remove the USB device whenever you want.

The playback mode can be checked with the play/shuffle/repeat indicator on the front panel display.

y

If the selected source contains folders, each folder will be played in repeat/

shuffle mode.

 Repeat playback

Press REPEAT on the remote control to select a playback mode

from the following.

:

All tracks within the folder (data CD/USB device only)

: All tracks

: 1 track

No display: Repeat mode off

 Shuffle playback

Press SHUFFLE on the remote control to select a playback mode

from the following.

:

All tracks within the folder (data CD/USB device only)

: All tracks

No display: Shuffle mode off

Listening to a USB device

Note

When a USB device is connected, tracks are played back in the

following order:

– Folder playback order:

folders are played in alphabetical order of the first 3 characters

of the folder name. Folder containing characters other than the

alphabet are played after alphabet character folders.

– File playback order:

files will be played back in order from files with the oldest wrote

date.

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

21

Top panel

Button Function

Top

Panel

/

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

PRESET Change the playback folder

Remote

control

Play/Pause

/

Skip

Search backward/forward

(press and hold down)

Stop

FOLDER Change the playback folder

USB

Folder number

File number

Repeat/shuffle playback

REPEAT

SHUFFLE

Remote control

10 En

Note

If you tune to an FM station manually, the sound will be in monaural.

1 Press SOURCE and set FM as the playback source.

2 Press / to tune the FM station.

Use the preset function to store your favorite 5 stations.

1 Press / to tune into your favorite FM station.

2 Press and hold down PRESET.

3 Press PRESET and select the preset number to

store the FM station.

4 Press and hold down PRESET to store the preset

station.

This stores the FM station.

LISTENING TO FM STATIONS

Selecting the FM station

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

12

Top panel

Tuning type Operation

Top

panel

Automatic

tuning

Press and hold down

or .

Manual

tuning

Press or repeatedly.

Remote

control

Automatic

tuning

Press and hold down

TUNING or .

Manual

tuning

Press TUNING or

repeatedly.

FM

Reception

frequency

Storing FM stations (preset)

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

234 1

Top panel

Using the remote control

Press and hold down MEMORY.

Using the remote control

Press PRESET /.

Using the remote control

Press MEMORY.

FM

Preset

number

11 En

LISTENING TO EXTERNAL SOURCES

English

1 Press SOURCE and set FM as the playback source.

2 Press PRESET repeatedly to select the preset FM

station.

Turn the system off before connecting audio cables. Remove the

terminal cover before connecting external devices.

1 Connect external audio device to AUX on the rear

panel using a commercially available 3.5 mm (1/8 in)

stereo mini plug cable.

Note

Turn down the volume of the unit and your external audio device before

connection.

2 Press to turn the system on.

3 Press SOURCE and set AUX as the playback

source.

4 Start playback on the connected external audio

device.

Selecting a preset FM station

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

1 2

Top panel

Using the remote control

Press PRESET /.

LISTENING TO EXTERNAL SOURCES

AUTO SET

DIMMER

CL

2

1

iPod

VOLUME

USB LAB

SOURCE ALARM SNOOZ

23

Top panel

AUX

75 Ω

FM ANT

AUX

12 En

The unit includes an alarm function (IntelliAlarm) that plays back music sources or set of beeps at the set time in a variety of different

methods. The alarm function has following features.

 3 types of alarms

Select from 3 alarm types, combining music and beep sounds.

 Various music sources

The iPod, audio CD, data CD, USB device and radio can be selected. The following can also be selected depending on the audio source:

* For information on creating a playlist, refer to the instructions for your iPod or iTunes.

 Test alarm

You can test the sound of the alarm when setting the alarm function.

 Snooze

The snooze function can be enabled to replay the alarm after 5 minutes.

USING THE ALARM FUNCTION

SOURCE + BEEP

The selected audio source and beep sound are played at the set time. This mode is recommended

for the best possible start to the day.

3 minutes before the set time: the source music begins to fade in and the volume gradually increases

as the alarm time approaches.

Alarm time: a beeping sound also begins playing.

SOURCE

The selected audio source is played at the set time. The volume fades in gradually and increases to

the set volume.

BEEP Only beep sound is played back at the set time.

Source Playback method Function

iPod

Playlist*

A specific playlist stored on the iPod can be played back repeatedly.

To play a playlist, create a playlist with the name “ALARM Yamaha

DTA” in advance.

When creating the playlist name, make sure there are spaces

between words, and take note of upper/lower case letters.

Resume

If the “ALARM Yamaha DTA” playlist cannot be found within the iPod,

the unit resumes play from the last track you played.

Audio CD

Selected track The selected track is played repeatedly.

Resume The track you listened to last time is played back.

Data CD/USB

Folder The selected folder is played repeatedly.

Resume The track you listened to last time is played back.

FM

Preset station The selected preset FM station is played.

Resume The FM station you listened to last time is played back.

13 En

USING THE ALARM FUNCTION

English

1 Press and hold ALARM.

The alarm indicator ( ) and set alarm time will flash.

2 Press / to set the alarm time.

3 Select the alarm type with the ALARM TYPE

switch on the rear panel.

For details on alarm types, refer to P. 12.

4 (when alarm types other than BEEP are selected)

Press SOURCE to select music source.

Sources other than AUX can be selected.

If iPod/CD/USB has been selected, connect/insert the audio

source (iPod, audio/data CD, USB device) to the unit.

Notes

• If the selected source is not connected or inserted, the selected track/

folder cannot be played.

• If source cannot be played back at the time set for the alarm (eg. iPod

is not connected), the beep sound is played back.

5 (when alarm types other than BEEP are selected)

Specify the track, folder or FM station to be played.

If iPod is set as the source:

No settings required.

If CD/USB/FM is selected as the source:

Press PRESET to select the track (audio CD), folder (data

CD/USB devise) or FM station to be played.

y

• When iPod is set as the source, the unit plays back the “ALARM

Yamaha DTA” playlist at the set alarm time. If this playlist cannot be

found within the iPod, the unit resumes play from the last track you

played (resume).

• When CD/USB is selected as the source and “0” is set as track/folder

number, the playback resumes from the track you listened to last time

(resume).

• When FM is selected as the source and preset number “0” is set, the

unit resumes broadcasting the last FM station you listened to

(resume).

6 Set the alarm volume by pressing VOLUME –/+

.

y

Press / to test the alarm. Press / again to stop testing.

7 Press ALARM to complete setting the alarm.

The alarm will be set, and the alarm indicator ( ) will

light up.

Note

The alarm setting will be erased if the system is turned off without

properly completing it.

Set the alarm time and alarm type

Using the remote control

Press / .

Using the remote control

Press Source button to select music source.

AUTO SET BEEP

SOURCE

+

BEEP

SOURCE

DIMMER

CLOCK

ALARM TYPE

2

1

2

1

VOLUME

USB LABEL SIDE

SOURCE PRESETALARM SNOOZE

SLEEP

17

2465

Top panel

Alarm indicator

Alarm time

BEEP

SOURCE+

BEEP

SOURCE

Rear panel

Using the remote control

Press PRESET /.

Alarm volume

CD

USING THE ALARM FUNCTION

14 En

1 Press ALARM.

When the alarm is on, the alarm indicator ( ) is shown,

and the alarm time is shown for a while. If you press ALARM

again, the alarm indicator ( ) and the alarm will turn off.

y

The set alarm time will be saved even if the alarm is turned off. If the

alarm is turned on again by pressing ALARM, the alarm will sound

with the previously alarm settings.

At the set time, the alarm sound is played back. During playback, the following operations are available.

1 (if you want to stop the alarm for a short time) Press

SNOOZE/SLEEP.

SNOOZE will stop the alarm and resume again in 5 minutes.

y

• When SOURCE + BEEP is set, press SNOOZE/SLEEP once to

stop the beep sound, and twice to stop the audio source. 5 minutes

after the audio source is stopped, it will start fading in again and the

beep sound will resume.

• The alarm indicator will flash when the snooze function is activated.

2 (if you want to turn the alarm off) Press ALARM or

.

y

The alarm stops automatically after 60 minutes unless you stop the

alarm.

Turning the alarm on/off

AUTO SET BEEP

SOUR

DIMMER

CLOCK

ALARM

2

1

2

1

iPod

VOLUME

USB LABEL SIDE

SOURCE ALARM SNOOZE

SLEEP

1

Top panel

Operations while playing back alarm sound

AUTO SET BEEP

SOUR

DIMMER

CLOCK

ALARM

2

1

2

1

iPod

VOLUME

USB LABEL SIDE

SOURCE ALARM SNOOZE

SLEEP

2

1

Top panel

15 En

English

You can set the time to turn off the system automatically.

1 Press SNOOZE/SLEEP a number of times to set

the time until the system turns off.

The sleep timer can be set to 30, 60, 90 and 120 minutes.

When the time is set, the sleep indicator ( ) is shown on the

front panel display.

y

If you press SNOOZE/SLEEP while the sleep timer is activated, the

sleep timer setting will be canceled.

1 Press one of the LOW/MID/HIGH EQ buttons on

the remote control while playing back.

Select the tone to be adjusted (LOW, MID, HIGH).

2 Press / to adjust the tone.

Each tone can be adjusted from –5 to +5.

3 Press ENTER to complete settings.

You can also press the EQ button that you pressed in Step 1

to complete the settings.

To change the tone of other audio frequencies, return to step

1 and press the EQ button to adjust the desired frequency.

1 Adjust the brightness with the DIMMER switch on

the rear panel.

AUTO: adjusts the brightness automatically to match the

surroundings.

1: brighter.

2: darker.

Note

When Auto is set, the brightness of the front panel display is adjusted

automatically with the brightness sensor (P. 3). Ensure that the sensor is

not covered.

USING THE SLEEP TIMER

AUTO SET BEEP

SOURC

DIMMER

CLOCK

ALARM T

2

1

2

1

iPod

VOLUME

USB LABEL SIDE

SOURCE ALARM SNOOZE

SLEEP

1

Top panel

TONE CONTROL

1

2

3

Remote control

iPod

Tone

Setting

Tone

ADJUST BRIGHTNESS OF FRONT PANEL DISPLAY

AUTO21

Rear panel

16 En

If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested solutions or if the

problem is not listed below, turn off and unplug the system, and consult the nearest authorized Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Solution

Can’t turn on the unit.

The power cable is not connect firmly. Reconnect the power cable into the wall outlet and

the unit firmly.

The speakers make no sound.

The volume may be set to the minimum level. Adjust the volume level.

The source may be incorrect. Select the correct source.

Sound suddenly turns off.

The sleep (☞ P. 15) may be set. Turn on the system and play the source again.

Sound is cracked/distorted or there is

abnormal noise.

Input source volume is excessive, or volume of this

unit is excessive (especially Bass).

Adjust volume with VOLUME, or adjust Bass with

EQ (☞ P. 15 ).

The unit does not operate properly.

The unit may have received a strong electrical

shock such as lightning or excessive static

electricity, or power supply may have dropped.

Turn the system off, and disconnect the power

cable. Wait about 30 seconds, reconnect the power

cable, and turn the system on.

The system turns on but immediately

shuts off.

A digital or high-frequency equipment

produces noises.

The unit may be placed too close to the digital or

high-frequency equipment.

Place the unit further away from the equipment.

The clock setting has been cleared.

The unit is left more than one week after you

disconnect the power cable from the wall outlet.

Plug the power cable into the wall outlet firmly, and

set the clock again (☞ P. 5).

iPod does not play back at the alarm time

even if SOURCE is set to iPod.

The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it

in the iPod dock again (☞ P. 2).

ALARM TYPE switch is set to BEEP. Set ALARM TYPE to SOURCE + BEEP or

SOURCE (☞ P. 13).

Clock flashes and the unit cannot be

operated.

CLOCK switch on the rear panel is set to SET, and

this unit is in clock setting mode.

Set CLOCK switch to CLOCK1 or CLOCK2

(☞ P. 5).

iPod

Problem Cause Solution

No sound.

The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it

in the iPod dock again (☞ P. 2).

The iPod software version has not been updated. Download the latest iTunes version from the Apple

website, and update the iPod software to the latest

version.

The iPod does not charge up.

The iPod is not connect in the iPod dock firmly. Remove an iPod from the unit, and then connect it

in the iPod dock again (☞ P. 2).

The system is set to power save mode (☞ P. 2).

Press to cancel the power save mode.

The iPod indicator flashes twice, and

repeated 3 times, after connecting the

iPod.

The iPod being used is not supported by the unit. Use a supported iPod (☞ P. 1 9).

17 En

TROUBLESHOOTING

English

CD playback

Problem Cause Solution

Disc cannot be inserted.

The system is set to power save mode.

Press to cancel the power save mode (☞ P. 2).

Some button operations do not work.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 18).

Playback does not start immediately after

pressing / .

The disc may be dirty. Wipe the disc clean.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 18).

If the unit was moved from a cold to warm place,

condensation may have formed on the disc reading

lens.

Wait for an hour or two until the unit adjusts to the

room temperature, and try again.

The CD indicator flashes twice, and

repeated 3 times, and the disc is ejected.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 18).

The disc may be dirty. Wipe the disc clean.

The disc does not contain playable files. Use a disc contains playable files (☞ P. 18, 19).

The disc is loaded back to front. Insert a disc facing the label side to near side.

“Err” is displayed in the front panel

display after loading a disc.

An error occurs in the unit.

Eject the disc with .

USB device playback

Problem Cause Solution

MP3/WMA file on the USB device does

not play.

The USB device is not recognized. Turn off the system and reconnect the USB device

to the unit.

Connect an AC adapter if supplied with the device.

If the solutions above do not resolve the problem,

the USB device is not playable on the unit.

The USB indicator flashes twice, and

repeated 3 times, after connecting a USB

device.

An incompatible USB device is connected to the

unit.

Turn off the system and reconnect the USB device

to the unit. If it does not resolve the problem, the

USB device is not playable on the unit.

The USB device does not contain playable files. Use a USB device contains playable files (☞ P. 18,

19).

“Err” is displayed in the front panel

display after connecting a USB device.

An incompatible USB device is connected to the

unit.

Turn off the system and reconnect the USB device

to the unit. If it does not resolve the problem, the

USB device is not playable on the unit.

An overcurrent is detected.

FM radio reception

Problem Cause Solution

Too much noise during stereo broadcast.

The antenna may be connected improperly. Make sure the antenna is connected properly

(☞ P. 3).

The radio station you selected may be far from your

area, or the radio wave reception is weak in your

area.

Try manual tuning to improve the signal quality

(☞ P. 10) or use a multi-channel outdoor antenna.

Even with an outdoor antenna, radio wave

reception is weak. (Sound is distorted.)

Multipath reflection or other radio interferences

may have occurred.

Change the height, direction, or placement of the

antenna.

Remote control

Problem Cause Solution

The remote control does not work

properly.

The remote control may be operated outside its

operation range.

For information on the remote control operation

range, refer to “How to use the remote control”

(P. 1).

The remote control signal receiver on the unit

(☞ P. 3) may be exposed to direct sunlight or

lighting (inverted fluorescent lamps).

Change the lighting or orientation of the unit.

The battery may be worn out. Replace the batteries with two new ones.

There are obstacles between the remote control

signal receiver on the unit and the remote control.

Remove the obstacles.

18 En

This unit is designed for use with audio CD, CD-R*, and CD-RW*

with the logos followings.

* ISO 9660 format CD-R/RW

y

This unit can play back discs bearing any of the logo marks above. A disc

logo mark is printed on the disc and the disc jacket.

Notes

• Do not load any other type of disc into this unit. Doing so may damage this

unit.

• CD-R/RW cannot be played back unless finalized.

• Some discs cannot be played back depending on the disc characteristics or

recording conditions.

• Do not use any non-standard shaped discs such as a heart-shaped disc.

• Do not use discs with many scratches on their surface.

• Do not touch the surface of the disc.

Hold a disc by its edge (and the center

hole).

• Do not use a pencil or pointed marker

to write on the disc.

• Do not put a tape, seal, glue, etc., on a disc.

• Do not use a protective cover to prevent scratches.

• Do not load more than one disc into this unit at one time. This

can cause damage to both this unit and the discs.

• Do not insert any foreign objects into the disc slot.

• Do not load a cracked, warped, or glued disc.

• Do not expose a disc to direct

sunlight, high temperature, high

humidity, or a lot of dust.

• If a disc becomes dirty, wipe it with

a clean, dry cloth from the center

out to the edge. Do not use record

cleaner or paint thinner.

• To avoid malfunction, do not use a

commercially available lens

cleaner.

• Insert only one CD into the system

at a time. Inserting two or more CDs may cause damage to both

the system and the CDs.

This unit supports USB mass storage class devices (e.g., flash

memories or portable audio players) using FAT16 or FAT32

format.

Notes

• Some devices may not work properly even if they meet the requirements.

• Do not connect devices other than USB mass storage class devices (such as

USB chargers or USB hubs), PCs, card readers, an external HDD, etc.

• Yamaha will not be held responsible for any damage to or data loss on the

USB device occurring while the device is connected to this unit.

• Playability of and power supply to all kind of USB devices are not

guaranteed.

Notes

• The unit can play back:

** Both constant and variable bitrates are supported.

• The maximum numbers of files/folders that can be played on the unit are

as follows.

• Copyright-protected files cannot be played back.

NOTES ON DISCS AND USB DEVICES

CD information

Handling a disc

Caution

USB device information

About MP3 or WMA files

File Bitrate (kbps)

Sampling

frequency (kHz)

MP3 8 - 320** 16 - 48

WMA 16 - 320** 22.05 - 48

Data CD USB

Maximum total number of file 512 9999

Maximum folder number 255 128

Maximum file number per folder 511 255

Sivu latautuu...

Yamaha ISX-800 Restio Omistajan opas

Tämä ohje sopii myös

Yamaha ISX-800 Restio Omistajan opas

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat