Yamaha TSX-112 Omistajan opas

TSX-112

Printed in Malaysia WY87360

G

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

TSX-112

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

i En

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place - away from direct sunlight, heat sources,

vibration, dust, moisture and cold. For proper

ventilation, allow the following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in an environment with high humidity (i.e. a room

with a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit,

and/or personal injury. Yamaha will not be held

responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power

cable disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press to set the system to

off, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the system off, then leave this

unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat

such as sunshine, fire or the like. When you dispose

of batteries, follow your regional regulations.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off by . In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a

CRT-based (Braun tube) TV set might impair picture

color. Should this happen, move this unit away from the

TV set.

1 En

English Français Deutsch Svenska Italiano Español Nederlands Русский

NAMES OF PARTS AND THEIR

FUNCTIONS...............................................2

CONNECTING AN iPod .............................6

ADJUSTING THE CLOCK..........................6

LISTENING TO iPod ..................................7

LISTENING TO CD AND USB DEVICE.....7

SWITCHING THE DISPLAY.......................8

LISTENING TO RADIO STATIONS ...........8

USING ALARM FUNCTION .....................10

SHUFFLE/REPEAT PLAYBACK ............. 12

LISTENING TO EXTERNAL SOURCE.... 12

USING SLEEP FUNCTION...................... 13

USING OPTION MENU ........................... 13

TROUBLESHOOTING............................. 14

NOTES ON DISCS AND

USB DEVICES......................................... 17

SPECIFICATIONS ................................... 18

CONTENTS

X Features

– iPod/iPhone, CD, USB device, radio and external device using AUX are playable.

– Providing comfortable wake-up by the music set with your preferred volume with alarm function.

Music, beep sound, or both can be set as alarm sound.

– Storing/calling your 30 favorite radio stations.

– Bass and treble can be controlled depending on your favorite.

X About this manual

• “iPod” described in this manual may also refer to “iPhone”.

• This manual describes how to operate this unit using buttons on the unit. Some of these operations are also

available using the remote control.

•The symbol “☞” with page number(s) indicates the corresponding reference page(s).

• Notes contain important information about safety and operating instructions.

y indicates a tip for your

operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a

result of improvements, etc. In case of differences between the manual and the product, the product has

priority.

X Supplied accessories

SNOOZE

/

SLEEP

ALARM

CD

RADIO

OPTION

MENU

FOLDER

PRESET

ENTER

VOLUME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

CLOCK

Remote control FM antenna

(With CR2032 battery)

Dock cover

2 En

PREPARATION

X Top panel, front panel

1 iPod dock: Set an iPod.

2 Disc slot (☞ P. 7)

3 : Press to turn the system on/off.

4 Alarm indicator: Lights up when the alarm function

is activated and flashes while setting the alarm.

(☞ P. 10)

5 SOURCE: Change sources.

6 Front panel display: Displays various information.

Time is displayed when the system is off.

If you set the system to power save mode, all the

information on the front panel display is turned off,

and reduce power consumption.

For more information how to set power save mode,

refer to “Rear panel (Connecting antenna)”.

(☞ P. 4)

7 : Ejecting the CD.

8 RETURN: Returns to the previous item while setting.

9 ENTER: Confirms the setting.

0 USB port (☞ P. 7)

y

When a USB device is connected to the USB port, the

device is charged. During system off/power save mode,

the device is not charged.

A (Headphones jack): Connect headphones.

B ALARM: Alarm on/off (☞ P. 11)

C PRESET (During receiving radios): Select the preset

radio station. (☞ P. 9)

– / +: Changes the setting (☞ P. 10)

D SNOOZE/SLEEP (☞ P. 11, 13)

E Audio control buttons: Skip, search backward/

forward, play/pause, stop, volume control

NAMES OF PARTS AND THEIR FUNCTIONS

SOURCE

RETURN

IPod/iPhone

ALARM

PRESET

SNOOZE

SLEEP

/

USB

ENTER

VOLUME

LABEL SIDE

SOURCE

RETURN

ALARM

PRESET

SNOOZE

SLEEP

/

USB

ENTER

VOLUME

IPod

/

iPhone

LABEL SIDE

1

3 4 5 6

2

7

0 A B E

8 9

D

C

NAMES OF PARTS AND THEIR FUNCTIONS

3 En

English

X Front panel display

1 SLEEP indicator: Lights up when the sleep timer is

on. (☞ P. 13)

2 PRESET indicator: Lights up when you preset radio

stations. (☞ P. 9)

3 STEREO indicator: Lights up when this unit is

receiving a strong signal from an FM stereo

broadcast.

4 AUTO indicator: Lights up when this unit is in the

Automatic Tuning mode. (☞ P. 8)

5 SHUFFLE indicator: Lights up when you set your

iPod/CD/USB to shuffle play. (☞ P. 12)

6 REPEAT indicator: Lights up when you set your

iPod/CD/USB to repeat play. (☞ P. 12)

7 MUTE indicator: Lights up when the sound is

muted.

8 Multi information display: Shows the various

information.

9 TUNED indicator: Lights up when this unit is tuned

into a station. (☞ P. 8)

0 MEMORY indicator: Flashes when searching for a

radio station by automatic preset tuning. Lights up

when you preset radio stations automatically or

manually. (☞ P. 9)

A Multi information indicators: Indicate the music

information currently displayed on Multi information

display. (☞ P. 8)

B Operation indicators: Shows the available menu

buttons for the currently selected OPTION menu

item.

SONGS

ALBUMS

ARTISTS

MEMORY

TUNED

SLEEP

STEREO

AUTO

SHUFFLE

REPEAT

MUTE

PRESET

1 234 756

9A

B

8

0

NAMES OF PARTS AND THEIR FUNCTIONS

4 En

X Rear panel (Connecting antenna)

1 FM antenna (supplied)

2 FM antenna terminal: Connect the supplied FM

antenna.

3 AUX: Connect an external device. (☞ P. 12)

4 CLOCK

SET: Adjusts the clock. (☞ P. 6)

ON: Displays the current time when system is off.

OFF: Switches the system to power save mode

when system is off.

All the information on the front panel display is

turned off in this mode. This can reduce power

consumption.

y

Even in system off/power save mode, the alarm function

is available.

5 Power cable: Connect to a wall outlet.

• The antenna should be stretched out.

• If you use an outdoor antenna instead of the supplied FM

antenna, reception will be better.

• If radio reception is poor, change the height, direction, or

placement of the antenna.

• If you use an FM antenna that is not supplied with the unit,

make sure that the base of the antenna is not threaded.

OFFSET ON

2 3 4

1

5

Notes

NAMES OF PARTS AND THEIR FUNCTIONS

5 En

English

X Remote control

1 Infrared signal transmitter

2 SNOOZE/SLEEP: Snooze/sleep setting.

(☞ P. 11, 13)

Press and hold this button, then press Cursor T/S

J ENTER to set the sleep function.

3 ALARM: Alarm on/off (☞ P. 11)

4 Source buttons: Change sources.

5 FOLDER (during data CD/USB playback): Change

folder.

6 , : Scrolls through items on the iPod’s screen.

7 OPTION: Displays the option menu. (☞ P. 13)

8 (Shuffle), (Repeat) (☞ P. 12)

9 TUNING (during receiving radio): Tuning radio

(☞ P. 8)

0 PRESET (during receiving radio): Select the preset

radio station (☞ P. 9)

A : System on/off

B CLOCK: Displays the time (☞ P. 6)

C , (during playback): Skip backward and

forward/press and hold to rewind and fast-forward

MENU: Returns to the upper level in the iPod menu.

: Play/pause

S/T/W/X (During using the option menu): Changes

the setting

ENTER

(During using the iPod): Select group/start playback

(During using the option menu): Confirms the setting

D : Stop playback.

E DISPLAY: Switches the information shown on the

front panel. (☞ P. 8)

F MUTE: Mute/resume the sound.

G VOLUME: Volume control

H MEMORY: Memories preset radio stations. (☞ P. 9)

X Using the remote control

Be sure to read “BATTERY CAUTIONS”

(☞ P. 18) before using the battery.

X Replacing the battery in the

remote control

While pushing the release tab in direction ,

slide out the battery holder in direction .

SNOOZE

/

SLEEP

ALARM

CD

RADIO

OPTION

MENU

FOLDER

PRESET

ENTER

VOL UME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

CLOCK

2

3

7

8

4

6

9

0

1

5

C

A

D

E

F

G

H

B

SNOOZE

/

SLEEP

ALARM

CD

RADIO

OPTION

MENU

FOLDER

PRESET

ENTER

VOLUME

USB

DISPLAY

MUTE

TUNING

MEMORY

iPod AUX

CLOCK

SOURCE

RETURN

ALARM

PRESET

SNOOZE

SLEEP

/

USB

ENTER

VOLUME

Within 6 m

(20’)

Battery insulation

sheet: Remove

before using.

1

2

3

CR2032

battery

6 En

CONNECTING AN iPod

Set your iPod in the iPod dock.

y

An iPod is charged when set in the iPod dock.

During power save mode, the iPod is not

charged.

• To secure the connection, attach a compatible

Dock Adapter supplied with the iPod or an

iPod Universal Dock Adapter (sold

separately), and remove the protective case

covering from your iPod.

• If you do not use an adapter or if the adapter

is not compatible, the connection could be

loose or poor, which could cause damage or

malfunctions. For details on dock adaptor

information, please visit official Apple’s

website.

• If an iPod in protective case is connected by

force, the connector may be damaged.

Remove the protective case before

connection.

• Attach the dock cover to the iPod dock

whenever you are not using it.

ADJUSTING THE CLOCK

1 Set CLOCK to SET.

2 Set the time.

Press – / + to set the hour and then

press ENTER.

Set the minutes in the same way.

y

• While setting the clock, press RETURN

to return to the previous setting.

• Press SNOOZE/SLEEP on the front

panel to switch between the 12 and 24

hour clock display.

3 Set CLOCK to ON to complete.

At the time ON is set, it will be 00

second and time count starts.

y

• The time is displayed for a certain period

when you press CLOCK on the remote

control.

• You can switch the system to power save

mode by setting CLOCK on the rear panel to

OFF.

The time settings are lost about 5 minutes after

unplugging the unit.

IPod/iPhone

LABEL SIDE

Dock Adaptor

Notes

1 2

Rear panel Front panel

PRESET

ENTER

3

Rear panel

Note

7 En

English

OPERATION

For details on compatible iPod models, refer to “SPECIFICATIONS” (☞ P. 18).

For details on how to operate the remote control, refer to “Remote control” (☞ P. 5).

y

This unit automatically turns off the system if the iPod is not connected and no operation is performed for 60

minutes.

X Listening to CD

X Listening to USB device

y

• If button is pressed during playback, next time playback starts from the beginning of the track you listened to last time. If

button is pressed again while playback is stopped, next time playback starts from the first track of the CD/USB device.

• For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 17).

• This unit automatically turns off the system 60 minutes after CD/USB device playback is stopped/paused.

LISTENING TO iPod

1 Set your iPod in the iPod dock.

2 Set SOURCE to iPod.

3 Play the iPod.

Playback operations are available with the

remote control, iPod and this unit.

y

• You can remove the iPod whenever you want.

• When music in the iPod is played back, this unit turns

the system on automatically and plays back the iPod

even if the unit is system off.

SOURCE

1 2

LISTENING TO CD AND USB DEVICE

1 Set SOURCE to CD.

2 Insert a CD.

Playback starts automatically. Playback

operations are available with the remote control

and this unit.

y

Playback for Data Disc starts in alphanumeric order of

files.

Insert the CD with the label side facing toward the front

of the unit.

1 Set SOURCE to USB.

2 Connect a USB device.

Playback starts automatically. Playback

operations are available with the remote control

and this unit.

y

• You can remove your USB device whenever you want.

• Playback starts in order by date and time of creation.

IPod/iPhone

LABEL SIDE

SOURCE

1 2

Note

SOURCE

RETURN

ALARM

PRESET

SNOOZE

SLEEP

/

USB

ENTER

VOLUME

1 2

SOURCE

SWITCHING THE DISPLAY

8 En

X Skipping folder for data CD/USB device

You can switch the playback information shown on the front panel display. Some special characters may not be

shown properly.

Select the folder with FOLDER.

Skip to the first file in the previous/next folder. The folder

name is displayed on the front panel display for a certain

period.

ROOT is displayed for the root folder when the directory

contains playable files.

FOLDER

Remote control

SWITCHING THE DISPLAY

Press DISPLAY repeatedly during playback.

iPod

Song number and elapsed time (default setting)

L

Song number and remaining time

L

Song name

L

Artist name

L

Album name

L

Back to the default setting

This function is available for iPod classic, iPod nano

(2nd generation and later), iPod touch and iPhone.

However, even with these models, this function may

not be available depending on the software version of

your iPod.

CD/USB

Track/file number and elapsed time of the current song (default

setting)

L

Track number and remaining time of the current song

*1

L

Total time of the disc

*1

L

Remaining time of the disc

*1

L

File name

*2

L

Track name

*3

L

Artist name

*3

L

Album name

*3

L

Back to the default setting

*1

Only for Audio CDs

*2

Only for MP3/WMA files

*3

Only when the selected track has information

LISTENING TO RADIO STATIONS

Tuning radio stations

1 Set SOURCE to FM.

2 For automatic tuning, press and hold TUNING.

For manual tuning, press TUNING repeatedly.

If you tune to a station manually, the sound is monaural.

DISPLAY

Press repeatedly

Remote control

Note

SOURCE

TUNING

1 2

Remote control

Note

LISTENING TO RADIO STATIONS

9 En

English

You can store your favorite 30 radio stations with the preset function.

X Automatic preset tuning

X Manual preset tuning

Presetting radio stations

1 Set SOURCE to FM.

2 Press and hold MEMORY for

more than 2 seconds.

y

To cancel the preset, press MEMORY again

before step 3 is completed.

3 Press ENTER.

The automatic preset starts.

When you perform the automatic preset, all

stored stations are cleared and the new stations

are stored.

1 Tune into a favorite radio station.

2 Press MEMORY.

3 Select the preset number you

want to store to.

y

To cancel the preset, press MEMORY

again.

4 Press ENTER to complete.

Selecting preset radio stations

1 Set SOURCE to FM.

2 Select the preset radio station

with PRESET.

y

You can delete a preset station by pressing

OPTION J Cursor S/T J ENTER on the

remote control to select PRESET DELETE.

SOURCE

MEMORY

ENTER

1 2

3

Remote control Remote control

Press and hold

Note

TUNING

MEMORY

1 2

Remote controlRemote control

MENU

ENTER

3 4

Remote controlRemote control

PRESET

1

SOURCE

2

10 En

This unit can play back your favorite music and/or beep sound at the set time. Alarm features on this unit are

described below.

• This unit has 3 alarm types combining music and beep sound:

• Alarm source played back at the set time can be selected from iPod, audio CD, data CD, USB

device, and radio. Depending on the source, followings also can be selected:

• Snooze function is also available.

X Setting the alarm time and sound

USING ALARM FUNCTION

Alarm features

SRC+BEEP

Selected audio source and the beep sound are played at the set time. Source playback begins to fade

in 3 minutes before the set time and the volume gradually increases to the set volume. Then, at the set

time, the beep sound is activated. This mode is recommended for a comfortable wake-up.

SOURCE

Selected source plays at the set time. Fade-in volume gradually increases to the set volume.

BEEP

Only beep sound is played back at the set time.

SOURCE Selectable item Function

iPod

Resume play The track you listened to last time is resumed.

Audio CD/Data CD/

USB

Track The Selected track is played back repeatedly.

Resume play The track you listened to last time is played back.

FM

Preset The selected preset radio station is played.

Resume play The radio station you listened to last time is played.

Alarm setting

1 Press and hold ALARM for more

than 2 seconds.

Alarm indicator ( ) and setting

items flash.

2 Set the alarm time.

Press – / + to set the hour and then

press ENTER.

Set the minutes in the same way.

3 Set the alarm type.

Select from SRC+BEEP, SOURCE

or BEEP. For the details on alarm

type, refer to “Alarm features”

(☞ P. 10).

4 Select the source (as required).

When you select SRC+BEEP or

SOURCE, select source. A source

other than AUX can be selected.

PRESET

ALARM

ENTER

1 2

Press and hold

3

PRESET

ENTER

4

PRESET

ENTER

(As required)

USING ALARM FUNCTION

11 En

English

X Switching the alarm on/off

At the set time, alarm sound plays back. During playback, operations below are available.

If source cannot be played back at the alarm time (ex. iPod is not set), beep sound is played back.

X Using the snooze function

5 Select a track or radio station (as

required).

When the source is CD/USB/FM,

select a track or radio station for

alarm.

y

• To select the last song or radio station you

listened to, select “---”.

• When the iPod is set as source, the track

you listened to last time is resumed.

6 Set the alarm volume.

To have the alarm sound at the last

volume level you used, select “---”.

Once you have set the alarm volume,

the alarm is set and the alarm indicator

( ) lights up.

y

• While setting the alarm, press RETURN to

return to the previous setting.

• To cancel without setting the alarm, press

ALARM before step 6 is completed.

Switch on/off the alarm function.

y

When the alarm is on, the alarm indicator

( ) lights up and alarm time is displayed

for a while.

Operations during playing back alarm sound

Press SNOOZE/SLEEP.

The alarm sound stops and resumes after

5 minutes.

y

• When SRC+BEEP is set, press SNOOZE/

SLEEP to stop the beep sound. press

SNOOZE/SLEEP again to stop the source.

The beep sounds 5 minutes after the source

stopped. The source fades in 1 minute before

the beep sounds.

• When the snooze function is activated, alarm

indicator flashes.

5

PRESET

ENTER

(As required)

6

PRESET

ENTER

ALARM

Note

SNOOZE

SLEEP

/

VOLUME

SHUFFLE/REPEAT PLAYBACK

12 En

X Stopping the alarm

y

• You cannot set SHUFFLE ALBUMS when you use an iPod touch or iPhone.

• When source contains folders, folder shuffle/repeat can be selected.

• For some iPod models, the shuffle and repeat functions may not be displayed or supported.

• When iPod is played back, the setting order of shuffle and repeat depends on the iPod model.

Press ALARM or .

y

• Unless you stop the alarm, the alarm stops

after 60 minutes automatically.

• The alarm function turns off when you stop

the alarm, but settings such as the alarm time

are saved for convenient use next time. To set

the alarm again, press ALARM.

SHUFFLE/REPEAT PLAYBACK

ALARM

Shuffle playback

Press repeatedly

Remote control

CD/USB iPod

SHUFFLE FOLDER

(Shuffle all songs in the

folder)

SHUFFLE ALL

(All shuffle)

SHUFFLE OFF

(Shuffle Off)

SHUFFLE SONGS

(Shuffle songs)

SHUFFLE ALBUMS

(Shuffle albums)

SHUFFLE OFF

(Shuffle Off)

Repeat playback

Remote control

CD/USB iPod

REPEAT ONE

(Single repeat)

REPEAT FOLDER

(Repeat all songs in the

folder)

REPEAT ALL

(All repeat)

REPEAT OFF

(Repeat Off)

REPEAT ONE

(Single repeat)

REPEAT ALL

(All repeat)

REPEAT OFF

(Repeat Off)

Press repeatedly

LISTENING TO EXTERNAL SOURCE

1 Connect your portable audio

device to AUX using a

commercially available 3.5 mm

(1/8 in) mini plug cable.

Turn down the volume of this unit and your

portable audio device before connection.

2 Set SOURCE to AUX.

3 Start playback on the connected

portable audio device.

4

Adjust the volume level of the unit

and the portable audio device.

SOURCE

1 2

Rear Panel

Note

13 En

English

You can set the time to turn off the system automatically.

The option menu appears on the front panel display by pressing OPTION on the remote control. You can set

various useful functions with option menu.

X Setting dimmer/tone

DIMMER: Changes the brightness of the front panel display.

TREBLE*: Adjusts the high frequency response.

BASS*: Adjusts the low frequency response.

* Also effective when you are using headphones.

USING SLEEP FUNCTION

1 Press and hold SNOOZE/

SLEEP for more than 2 seconds.

2 Select the sleep time from 30,

60, 90,120 and SLEEP OFF.

When the time is set, the sleep

function is set to on, and the SLEEP

indicator lights up.

y

To exit without changing the current

setting, press SNOOZE/SLEEP.

USING OPTION MENU

Option menu Parameter or control range Reference page

PRESET DELETE

(Displays only when the input source is set to FM.) 9

DIMMER

DIMMER OFF (brightest)/DIMMER 1/DIMMER 2 (darkest) This page

TREBLE

-10 dB to +10 dB This page

BASS

-10 dB to +10 dB This page

AUTO POWER

OFF

TIME OFF/ TIME 8H/ TIME 4H

AUTO POWER OFF sets the system to system off or power save mode

whenever no operation is performed for a preset amount of time.

This page

1 Press OPTION.

2 Select desired option menu with

S/T.

3 Confirm with ENTER.

4 Change the settings with S/T.

5

Complete the setting with

ENTER

.

To set additional items, repeat steps 2 to 5.

6 Exit option menu with OPTION.

y

To cancel without changing the settings, press

OPTION before step 5 is completed.

SNOOZE

SLEEP

/

VOLUME

Press and hold

PRESET

ENTER

2

1

OPTION

MENU

ENTER

1 2

3

Remote control Remote controlRemote control

MENU

ENTER

4 5

6

ENTER

OPTION

Remote control Remote controlRemote control

14 En

ADDITIONAL INFORMATION

In case of a problem with the unit, check the following list first. If you cannot solve your problem with the

suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest

authorized Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Solution

The speakers make no

sound.

The volume may be set to the minimum level.

Adjust the volume level.

The source may be incorrect. Select the correct source.

Headphones are connected. Remove the headphones.

Sound is cracked/distorted

or there is abnormal noise.

Input source volume is excessive, or

volume of this unit is excessive

(especially Bass).

Adjust volume with VOLUME, or adjust

Bass with the option menu (☞ P. 13).

The unit does not operate

properly.

The unit may have received a strong

electrical shock such as lightning or

excessive static electricity, or power

supply may have dropped.

Set the system to off, and disconnect the

power cable. Wait about 30 seconds,

reconnect the power cable, and turn on the

system.

The system turns on but

immediately shuts off.

A digital or high-frequency

equipment produces noises.

The unit may be placed too close to the

digital or high-frequency equipment.

Place the unit farther away from the

equipment.

The clock setting has been

cleared.

The unit is left more than five minutes

after you disconnect the power cable

from the wall outlet.

Plug the power cable into the wall outlet

firmly, and set the clock again (☞ P. 6).

When it is time for the alarm

to sound, only a beep is

heard; no music is heard.

The alarm source you have selected is

not connected or inserted.

If you have selected iPod or USB, make

sure the device is connected. If you have

selected CD, make sure the CD is inserted.

The alarm type is set to BEEP. Set the alarm type to SRC+BEEP or

SOURCE (☞ P. 10).

Clock flashes and the unit

cannot be operated.

CLOCK on the rear panel is set to SET,

and this unit is in clock setting mode.

Set CLOCK on the rear panel to ON

(☞ P. 6).

The system is suddenly

turned off.

The automatic system off function turned

the unit off.

This unit automatically turns off the system

60 minutes after USB device or CD

playback is stopped.

The sleep (☞ P. 13) may be set.

Turn on the system and play the source again.

The AUTO POWER OFF function is

triggered.

Setting

AUTO POWER OFF

to TIME OFF

enables to play continuously (

☞

P. 13).

Radio reception

Problem Cause Solution

Too much noise during

stereo broadcast.

The antenna may be connected

improperly.

Make sure the antenna is connected

properly (☞ P. 4).

The radio station you selected may be far

from your area, or the radio wave

reception is weak in your area.

Try manual tuning to improve the signal

quality (☞ P. 8) or use a multi-channel

outdoor antenna.

Even with an outdoor antenna,

radio wave reception is weak.

(Sound is distorted.)

Multipath reflection or other radio

interferences may have occurred.

Change the height, direction, or placement

of the antenna.

TROUBLESHOOTING

15 En

English

In case of a transmission error without a status message appearing in the front panel of this unit, check the

connection to your iPod (☞ P. 6).

iPod

Status message Cause Remedy

iPod Connecting

iPod Charging

This unit is in the middle of recognizing

the connection with your iPod.

If the message continues to appear in the

front panel display and playback does not

start, connect the iPod again (☞ P. 6).

Unknown iPod

There is a problem with the signal path

from your iPod to this unit.

Connect the iPod again (☞ P. 6).

The iPod being used is not supported by

this unit.

Only iPod classic, iPod nano (2nd

generation and later), iPod touch and iPhone

are supported.

iPod

This unit has recognized your iPod;

however, it cannot obtain information

such as elapsed time.

iPod Unplugged

Your iPod was removed from the iPod dock. Station your iPod back in the iPod dock (

☞

P. 6).

Over Current

The iPod being used is not supported by

this unit.

Disconnect the iPod and then turn the

system off and on again. Then connect

supported iPod again (☞ P. 18).

The iPod is connected at an angle.

Problem Cause Solution

No sound

The iPod is not set in the iPod dock

firmly.

Set the iPod firmly.

Headphones are connected. Remove the headphones.

The iPod software version has not been

updated.

Download the latest iTunes software to

update the iPod software version to the

latest.

The iPod does not charge up.

The iPod is set in the iPod dock

improperly.

Remove the iPod from the unit, and then set

it in the iPod dock again (☞ P. 6).

The system is set to power save mode

(☞ P. 2).

Set CLOCK to ON on the rear panel to

cancel power save mode (☞ P. 4).

Suddenly the music being

played back is canceled and

another track starts playing

without performing any

operation.

The iPod’s Shake to Shuffle function is

turned on.

Turn off the Shake to Shuffle function in

the iPod’s settings.

Remote control

Problem Cause Solution

The remote control does not

work properly.

The remote control may be operated

outside its operation range.

For information on the remote control

operation range, refer to “Using the remote

control” (☞ P. 5).

The remote control sensor on the unit

may be exposed to direct sunlight or

lighting (inverted fluorescent lamps).

Change the lighting or orientation of the

unit.

The battery may be worn out. Replace the battery with a new one.

There are obstacles between the sensor

of the unit and the remote control.

Remove the obstacles.

Note

TROUBLESHOOTING

16 En

In case of a transmission error without a status message appearing in the front panel of this unit, check the

connection to the USB device (☞ P. 7).

Disc playback

Problem Cause Solution

Disc cannot be inserted.

The system is set to power save mode (

☞

P. 2).

Set CLOCK to ON on the rear panel to

cancel power save mode (☞ P. 4).

Some button operations

do not work.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 17).

Playback does not start

immediately after

pressing .

The disc may be dirty. Wipe the disc clean.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 17).

If the unit was moved from a cold to warm

place, condensation may have formed on the

disc reading lens.

Wait for an hour or two until the unit adjusts

to the room temperature, and try again.

“No Disc” or “Unknown

Disc” is displayed in the

front panel display after

loading a disc.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 17).

The disc may be dirty. Wipe the disc clean.

The disc is loaded back to front. Insert a disc facing the label side to near side.

The disc does not contain playable files. Use a disc contains playable files (☞ P. 17).

An error occurs in the unit. Unload the disc with .

USB device playback

Status message Cause Remedy

USB Unplugged

The USB device is not connected firmly. Connect the USB device again (☞ P. 7).

Unknown USB

The connected USB device is not playable on

this unit.

Connect playable USB device (☞ P. 17).

The file name is too long. The file name should be no more than 250

characters.

Over Current

The USB device is connected at an angle. Disconnect the USB device and then turn the

system off and on again. Then connect

playable USB device again (☞ P. 17).

No Files

The USB device does not contain playable

files.

Use a USB device contains playable files

(☞ P. 17).

An incompatible USB device is connected to

the unit.

Turn off the system and reconnect the USB

device to the unit. If it does not resolve the

problem, the USB device is not playable on

the unit.

USB Time Out

The number of files/folders exceeds the

limit.

Reduce the number of files/folders; refer to

the limitations noted in this manual (☞ P. 17).

Problem Cause Solution

MP3/WMA file in the USB

device does not play.

The USB device is not recognized. Turn off the system and reconnect the USB

device to the unit.

Connect an AC adapter if supplied with the device.

Format the USB device and copy the files again.

If the solutions above do not resolve the problem,

the USB device is not playable on the unit.

Note

17 En

English

This unit is designed for use with audio CD, CD-R

*1

,

and CD-RW

*1

with the logos followings.

*1

ISO 9660

y

This unit can play back discs bearing any of the logo marks

above. A disc logo mark is printed on the disc and the disc

jacket.

• Do not load any other type of disc into this unit. Doing so

may damage this unit.

• CD-R/RW cannot be played back unless finalized.

• Some discs cannot be played back depending on the disc

characteristics or recording conditions.

• Do not use any non-standard shaped discs such as a heart-

shaped disc.

• Do not use discs with many scratches on their surface.

• Do not touch the surface of

the disc. Hold a disc by its

edge (and the center hole).

• Do not use a pencil or

pointed marker to write on

the disc.

• Do not put a tape, seal, glue, etc., on a disc.

• Do not use a protective cover to prevent scratches.

• Do not load more than one disc into this unit at one time.

This can cause damage to both this unit and the discs.

• Do not insert any foreign objects into the disc slot.

• Do not load a cracked, warped, or glued disc.

• Do not expose a disc

to direct sunlight,

high temperature,

high humidity, or a

lot of dust.

• If a disc becomes

dirty, wipe it with a

clean, dry cloth from

the center out to the

edge. Do not use

record cleaner or

paint thinner.

• To avoid

malfunction, do not

use a commercially

available lens

cleaner.

This unit supports USB mass storage class devices

(e.g., flash memories or portable audio players) using

FAT16 or FAT32 format.

• Some devices may not work properly even if they meet the

requirements.

• Do not connect devices other than USB mass storage class

devices (such as USB chargers or USB hubs), PCs, card

readers, an external HDD, etc.

• Yamaha will not be held responsible for any damage to or

data loss on the USB device occurring while the device is

connected to this unit.

• Playability of and power supply to all kind of USB devices

are not guaranteed.

• USB devices that use encryption cannot be used.

• The unit can play back:

*2

Both constant and variable bitrates are supported.

• The maximum numbers of files/folders that can be

displayed on the unit are as follows.

*3

The root is counted as one of the folders.

• Copyright-protected files cannot be played back.

NOTES ON DISCS AND USB DEVICES

Disc information

Handling a disc

Notes

Caution

USB device information

About MP3 or WMA files

File Bitrate (kbps)

Sampling

frequency (kHz)

MP3

8 - 320

*2

16 - 48

WMA

16 - 320

*2

22.05 - 48

Data CD USB

Maximum total number of file

*3

512 9999

Maximum folder number

*3

255 999

Maximum file number per folder

511 255

Notes

18 En

X PLAYER SECTION

iPod (Digital connection)

• Made for ......iPod touch (1st, 2nd, 3rd, and 4th generation)

iPod classic

iPod nano (2nd, 3rd, 4th, 5th, and 6th generation)

iPhone 4

iPhone 3GS

iPhone 3G

iPhone

CD

• Media........................................................... CD, CD-R/RW

• Audio format ................................. Audio CD, MP3, WMA

Laser

• Type.............................Semiconductor laser GaAs/GaAlAs

• Wave length .............................................................790 nm

• Output Power .............................................................7 mW

USB

• Audio format ....................................................MP3, WMA

AUX

• Input connector........... 3.5 mm (1/8 in) STEREO mini Jack

X AMPLIFIER SECTION

• Maximum output power .................................15 W + 15 W

(6 Ω 1 kHz, 10% THD)

• Headphones ............................3.5 mm STEREO mini Jack

(Adaptive Impedance 16 to 32 Ω)

X TUNER SECTION

• Tuning range

FM .................................................. 87.50 to 108.00 MHz

X GENERAL

• Power Supply............................................AC 230 V, 50 Hz

• Power consumption ..................................................... 23 W

• System off consumption............................................. 2.7 W

• Power save consumption ............................................0.2 W

• Dimensions (W × H × D) ... W457 × H180.5 × D173.5 mm

(18 × 7 1/8 × 6 7/8 in)

• Weight ...................................................... 5.1 kg (11.2 lbs.)

Specifications are subject to change without notice.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt

to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid

direct eye exposure to beam. When this unit is plugged into

the wall outlet, do not place your eyes close to the opening of

the disc tray and other openings to look into inside.

iPod, iPhone

“Made for iPod,” and “Made for iPhone” mean that an

electronic accessory has been designed to connect

specifically to iPod, or iPhone, respectively, and has been

certified by the developer to meet Apple performance

standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod or iPhone

may affect wireless performance.

iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod

touch are trademarks of Apple Inc., registered in the U.S. and

other countries.

BATTERY CAUTIONS

• If the battery grows old, the effective operation range of the

remote control decreases considerably. If this happens,

replace the battery with new one as soon as possible.

• Exhausted battery may leak. If the battery have leaked,

dispose of it immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before installing

a new battery.

• Keep the battery away from children. If the battery is

accidentally swallowed, contact your doctor immediately.

• When not planning to use the remote control for long

periods of time, remove the battery from the remote

control.

• Do not charge or disassemble the supplied battery.

SPECIFICATIONS

The laser component in this product is capable of

emitting radiation exceeding the limit for Class 1.

Sivu latautuu ...

Yamaha TSX-112 Omistajan opas

Yamaha TSX-112 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat