Sony KV-28FC60Z Ohjekirja

R

4-205-029-12

Trinitron Colour

Television

Instruction Manual

GB

KV-28FC60/28FC60/Z

KV-32FC60/32FC60/Z

Styrfunktioner

Betjeningsvejledning

Kayttöohje

OδηγίεςXpήσης

Bruksanvisning

SE

NO

FI

DK

GR

Bedienungsanleitung

DE

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or

BSI to BS 1362 (i.e. marked with 2 or @ ) must be used.

When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the

circuit should be protected by a 5 AMP FUSE at the distribution board.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

•

IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and

an appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black. The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red. Do not connect either wire to the

earth terminal in the plug which is marked by the letter E or by the safety earth symbol

or

coloured green or green and yellow.

WARNING

• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket

outlet. This plug cannot be used and should be destroyed.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing

to qualified personnel only.

1

GB

2

Safety First

TV sets operate on extremely high voltages. To prevent fire or an electric shock, please follow

the safety information below:

For General Safety

v

This TV set is designed to receive and reproduce audio and video signals.

Any other use of the TV set is not permitted.

v

Never open the rear cabinet.

v

Refer servicing to qualified personnel only!

v

Do not expose the TV set to rain or moisture.

For Safe Installation

v

Do not block or cover the ventilation openings. For ventilation leave a space of at

least 5 cm around the set.

v

Do not install the TV set in hot, humid or excessively dusty places.

v

Do not install the TV set where it may be exposed to mechanical vibrations.

v

Place the TV set only on a stable stand designed for the weight and dimensions of the TV.

For Safe Operation

v

Operate the TV set only on a 220- 240 V. AC, 50 Hz supply.

v

Unplug the TV set if any liquid or solid object falls in through the ventilation openings.

Have it checked immediately!

v

When not in use, do not leave the TV set in standby mode. Disconnect the TV set

if you are not going to use it for a longer period.

v

Disconnect the TV set only by pulling on the mains plug.

Do not pull on the power cord itself.

v

In the event of a thunderstorm, you should not touch the aerial, mains plug or television. It

could possibly cause an electric shock.

For Maintenance

v

When the TV is switched off, clean the screen with a soft dampened cloth. Do not use any

abrasive cleaners.

v

Dust and nicotine deposits may cause heat accumulation inside the TV set.

In the long term this could be a safety risk and may shorten the lifetime of your TV set.

Therefore have your set serviced about every five years.

3

Installation 4

1. Checking the accessories supplied 4

2. Inserting batteries into the remote control 4

3. Connecting the TV 5

4. Switching on the TV 6

5. Using your joystick 6

6. Tuning your TV 7

7. Finding your video channel 7

Operation 8

Overview of the TV set buttons 8

Overview of the remote control buttons 9

NexTView 10

Teletext 12

Using the TV menu system 14

Adjusting picture and sound 14

Using the Features menu 16

Changing the screen mode 17

Sorting TV channels 18

Manually tuning in channels 18

Naming a channel 19

Skipping programme positions 19

Using the Further Programme Preset function 20

Adjusting the picture geometry for an RGB source 20

Adjusting the picture rotation 21

Changing the speaker configuration for external loudspeakers 21

Inputting your Personal ID 22

Presetting and labelling of input sources 22

Optional Equipment 23

Selecting an input signal 23

Smartlink 24

Remote control of other Sony equipment 24

Additional Information 25

Specifications 25

Troubleshooting 26

Channel Guide 26

Table of Contents

4

Installation

Follow steps 1-7 to install the TV and view TV programmes.

Always remember to dispose of used batteries in an environmentally friendly way.

2. Inserting batteries into the remote control

1. Checking the accessories supplied

1 x remote control

2 x batteries (AA size)

5

Installation

3. Connecting the TV

1 Connect your existing aerial lead to the socket marked ˘ on the rear of the TV set.

Connecting an aerial to your TV

Connecting an aerial and VCR to your TV

1 Connect your existing aerial lead to your VCR as shown.

2 Connect the VCR aerial lead from the RF OUT socket on the back of the VCR to the aerial socket on the back of the

TV as shown.

3 Connect the VCR set to the mains and switch on.

4 Insert a pre-recorded tape into the VCR and press the ‘PLAY‘ button.

L/G/S/IR/D/D/D

R/D

D/D

L/G

S/I

1

2

S

2

3

S

3

If you are not connecting

your TV to a VCR, please

connect the aerial lead (as

shown left) and proceed to

section ‘4.Switching on the

TV‘.

If you are connecting your

TV to a VCR please refer to

the section below.

The scart lead is optional. If it

can be used however, this

additional connection can

improve picture and sound

quality when in play mode.

L/G/S/IR/D/D/D

R/D

D/D

L/G

S/I

1

2

S

2

3

S

3

OUT

IN

AC IN

(scart lead -

not supplied)

(existing aerial lead)

6

Installation

If the standby mode indicator u on the front of the TV is lit,

press the TV button on the remote control to switch on

the TV set. Please be patient as the picture may take a few

moments to appear on the TV screen.

1 Connect the TV plug to the mains socket (220-240 V. AC, 50 Hz).

2 Push in the on/off button U on the front of the TV.

4. Switching on the TV

5. Using your joystick

Moving the

joystick

Pressing the

joystick

To move around the menus press

the relevant arrow button.

To select an item in a menu press the

joystick down in the middle.

7

1 The Language/Country menu appears on the TV

screen with the word ‘English‘ highlighted.

2 Push the joystick to $ or 4 to select your chosen

language then press the OK button to confirm. The

country menu appears on screen with the word ‘OFF‘

highlighted. Select ‘OFF‘ if you do not want your

channels stored in a given channel sequence starting

from programme position 1.

3 Push the joystick to $ or 4 to select the country in

which you wish to operate the TV.

4 Press the OK button to confirm your choice. The ‘Set-

up‘ menu appears on the TV screen.

5 Push the joystick to $ or 4 to select ‘Auto Tuning‘

then press the OK button to confirm.

6 Push the joystick to ” and hold for 5 seconds.

v

Your TV will now start to tune in all available

channels. This may take a few minutes - please be

patient and do not press any buttons. Once the TV

has tuned all available channels the menu disappears

from the screen and your TV is ready to use.

v

If you would like to stop the autotune process at any

stage, press the OK button. The manual sort menu

appears on the TV screen. For manual sorting

instructions refer to the ‘Sorting TV channels‘ section

of this instruction manual. To remove the sorting

menu, press the MENU button on your remote

control.

Language/Country

Language

Country

Select language:

Confirm: OK

Cestina

Dansk

Deutsch

English

Español

Français

Italiano

ˇ

Set Up

Auto Tuning

Programme Sorting

AV Preset

Installation

Select:

Start Auto Tuning:

Start

1

2

3

4

5

CO2

CO3

CO4

CO7

CO8

Searching

Language/Country

Language

Country

Select Country:

Confirm: OK

English

Off

Austria

Belgium

Bulgaria

Czech Rep.

Denmark

Finland

Installation

Before you tune your TV, you will be asked to set your language and country.

6. Tuning your TV

7. Finding your video channel

If you have connected a VCR to your TV, you now need to find your video channel.

1. Press the PROGR+/- buttons on your remote control until your video picture appears on the TV screen.

v

If you wish to move your video channel to a different programme position, refer to the ‘Sorting TV channels‘

section of this instruction manual.

8

+

–

+

–

PROGR

CONTROL

Operation

You must press the control button to activate and illuminate the control panel before you can use the other buttons on top

of the TV set.

Overview of the TV set buttons

Video input button.

Press to select the input signals

from VCR etc.

Volume control buttons.

Press to increase (+)/

decrease (-) volume.

Programme Up (+) or

Down (-) buttons.

Press to select TV

channels.

CONTROL button.

Press to activate and

illuminate the control panel.

On/Off switch.

Press to switch TV on

and off.

9

Soul Music

News

Game Show

Animal Report

Stones in Interviev

Pink Panther

Afternoon Report

VIVA

RTL

SAT 1

S3

VIVA 2

PRO 7

ARD

8

9

10

11

12

13

14

Overview of the remote control buttons

Operation

VCR on/off button.

Press to temporarily switch off

VCR (if Sony VCR connected).

Press again to switch on VCR.

To temporarily switch off TV

Press to temporarily switch off TV. Press again

to switch on TV from standby mode.

NOTE: After 15 minutes without a TV signal

and without any button being pressed, the TV

switches automatically into standby mode.

To reveal channel information.

Press to reveal information on the channel you are

currently watching. Press the

+

;

button again to

remove the display.

To mute sound.

Press to mute TV sound. Press again to

restore the sound.

To return to TV mode.

Press to return to the normal operation

from teletext mode, video mode or

standby mode.

To select Teletext

Press to select Teletext mode.

To select EPG

Press to display the Electronic Programme

Guide. Press again to remove display.

To select input signal or freeze teletext

Press to select inputs from the TV sockets (see Using

Optional Equipment section). In teletext mode,

press to freeze the displayed page. Press once again

to cancel.

These buttons have no function.

To freeze the picture.

Press to freeze the picture. Press again to

cancel freeze.

To return to previous channel

Press to return to the previous channel you were

watching. Note: This can be done only after

watching the present channel for 5 seconds.

To change screen format.

Press to change the size of the screen.

This button can be used in Teletext mode only.

Please see Teletext section of manual for details.

To select channels.

Press numbered buttons to select channels.

For double digit programme numbers, eg 23,

press -/-- first, then the buttons 2 and 3. If you

enter an incorrect first digit, this should be

corrected by entering another digit (0-9) and

then selecting -/-- button again to enter the

programme number of your choice.

To select menu items

Use this OK button to select options available in

the menu system of the TV.

To select channels.

Press to select channels.

To display the menu

Press if you wish to use the TV menu system. Press

again to remove the menu from the TV screen.

To display sound menu.

Press repeatedly to select one of the

following equaliser modes : Personal,

Vocal, Jazz, Rock, Pop or Flat.

To display picture menu.

Press to change the picture settings. Press the ;

button to remove the display.

To adjust TV volume.

Press to adjust the volume of the TV.

To reset to factory-set levels.

Open the remote control lid and press to return

picture and sound settings to factory-set levels.

After the ‘Installation‘ menu has appeared on

the TV screen, refer to the ‘Selecting Language

and Country‘ section of the instruction manual

to change your choice of language and country

if desired.

To display the time.

Open the remote control lid and press to display the

time on screen.

To operate video equipment

Open the remote control lid and press these buttons

to operate your video equipment (please refer to

your VCR manual).

To display the

Channel Table

Press the OK button to

display the channel

table. Push to $ or 4 to

select a channel then

push to ” to confirm.

10

NexTView*

*depending on availability of service

NexTView is an electronic programme guide with up to 1 week* of programme information on

those channels included in the selected provider.

*If the data exceeds the memory of NexTView, you will get information on less than 7 days.

When looking for information you can search by theme (sports, art etc.), date or time (e.g.

broadcasts between 8 and 9 p.m). When you‘ve found a programme you can go directly to this

programme, use the timer to remind you of it or preset your VCR with Smartlink.

The NexTView provider is responsible for the contents of the guide. The TV set is responsible

for the presentation, that is the menu structure and the navigation, if there is none from the

provider. If there is a navigation from the provider the basic operation with the joystick is the

same as described in the Sony navigation.

Displaying NexTView

At first you need to select a channel providing a NexTView Service. In this case the indication

“NexTView“ is displayed as soon as all data is available. When you later change the channel

you can still select this NexTView service.

1 Press

to switch NexTView on and off.

2 Use the joystick buttons as follows

•

moving up- or downwards within a column: Use $ or 4

•

Going to the left columns time and date: Use “

•

Going to the right column icons: Use ”

•

Confirming a selection: Press OK

a while in the columns date, time or icon (themes), the programme list changes according

to the selection.

b while in the programme list, confirming a running broadcast brings you directly to the

TV programme or confirming a future programme brings you to the long info menu

(See Using the Long Info Menu).

Index

full list of selection sports

personal selection entertainment

news broadcasts children

movies back to last menu

7

Tu e

07 Tue

12:38

8

Wed

10

Fri

11

Sat

12

Sun

13

Mon

9

Thu

12

SWISS

Star Wars

Super RTL

Documentary series which follows veterinary

graduates as they embark on their careers.

Continues on Friday

Vets in Practice

C5

Flui grüsst den Rest der Welt

Kabel 1

Once upon a time in the West

Euronews

International News

RTL Plus

10:35 - 12:45

10:20 - 12:00

10:45 - 10:50

11:00 - 11:20

11:45 - 12:50

TXT TPS / RINGIER

Tue 07. 04 .98

Operation

11

Using the Individual Setting menu

When you select there will be no personal pre-selection. lets you make your own

individual selection of themes, limiting the search to the marked ones.

1 Select

using 4 or $. Push to ” to enter.

The Individual Setting menu is displayed.

2 Select the item you wish to mark using 4 or $. Confirm by pressing OK.

Repeat step 2 for all items you wish to have in your list.

3 When you have finished the list, press ” to select

on the menu screen then press OK.

Using the Long Info menu

1 Select a future programme in the column programme list using 4 or $. Press OK.

The long info menu is displayed.

You wish to record the selected programme with your VCR

(only with Smartlink VCRs)

2 Select

using “ and press OK.

The information is transferred to the VCR connected to your TV set.

Setting up your VCR

3 Select VPS/PDC pushing repeatedly to “.

With this setting on, you have the guaranteed recording of the whole broadcast should

there be a change in the TV programme. This only works if the selected channel

broadcasts a VPS/PDC signal.

•

Select On or Off using OK.

4 Select Speed using $.

Select between standardplay (SP) or longplay (LP) mode. With longplay you can record

twice as much on a videotape. The picture quality, however, may suffer.

•

Select SP or LP using OK.

5 Select VCR Setup using $.

Select with which of the connected Smartlink-VCRs you wish to programme.

•

Select VCR 1 or 2 using OK.

To leave the menu

6 Select

using z. Press OK.

You are back in the last menu.

07 Tue

12:38

Address Mapping

The position of the addresses in the

OSDA is shown in the following diagram.

The position values of the DPW are set

to '0'.

If other values are set, the complete

combination will be scrolled.

Example:

if the DPWC is set to '63', the char-

Speed

Timer Prog

VPS/PDC

SP

VCR1

On

This channel has been set for a timer

First nextTView/EPG-Providers in Europe

SWISS TXT TPS / RINGIER nexTView

Tue 07. 04 .98

Speed

VCR Setup

VPS/PDC

SP

VCR1

On

Operation

12

Most TV channels broadcast information via teletext. The index page of the teletext

service (usually page 100) gives you information on how to use the service.

Please use a TV channel with a strong signal, otherwise there may be

Teletext errors.

216-02

01 03 04 05 06 07 0802

Operation

Teletext

Switching Teletext on and off

1 Select the TV channel which carries the teletext service you want to view.

2a Press the button once on your remote control to switch Teletext on.

b Press

again for Mix mode.

The TV broadcast and the Teletext display are overlapped.

3 Press ; or press a third time to switch teletext off.

Selecting a Teletext Page

Input the three digits of the page number using the number buttons on your remote

control.

If you have made a mistake:

Type in any three digits, then re-enter the correct page number.

Page Catching

1 Using the number buttons on the remote control, select a teletext page which

has several page numbers on it (e.g. the index page).

2 Press the OK button.

Page Catching is displayed.

3 Select the desired page number using 4 or $ then press the OK button.

The requested page is displayed after some seconds.

Selecting the next or the preceding page

•

Press (Page +) or (Page -).

Selecting the index page

•

Press

+

;

.

Selecting a subpage

A teletext page may consist of several subpages. In this case an information line

is displayed, showing the number of subpages.

•

Select the mode by pushing to 4. Select the subpage by using 4 or $.

Freezing a Teletext subpage

1 Press to freeze the Teletext page.

2 Press

to resume normal teletext reception.

Using Fastext*

*depending on availability of service

Fastext lets you access pages with one button stroke. When Fastext is broadcast,

a colour-coded menu appears at the bottom of the screen. The colours of this

menu correspond to the red, green, yellow and blue buttons on the remote

control.

•

Press the coloured button which corresponds to the colour in the

colour-coded menu.

13

Using the Teletext menu

This TV set has a menu-guided teletext system. When teletext is switched on

you can use the joystick buttons to operate the teletext menu.

Select the menu functions as follows:

1 Press the MENU button on the remote control to display the Teletext menu.

2 Select the teletext function using 4 or $. Push to ” to enter.

Top/Bottom/Full

For convenient reading of a Teletext page you can enlarge it.

After having selected the function, a sub menu Top 4 Bottom $ Full OK

is displayed.

•

Push to 4 to enlarge the upper half of the screen, push to $ to enlarge the lower

half. Press OK to resume the normal size. Press

to resume the normal

Teletext operation.

Text Clear

After having selected the function, you can watch a TV channel while waiting

for a requested Teletext page. As soon as the page is available, the symbol

changes colour.

•

Press to view the page.

Reveal

Some teletext pages contain hidden information (e.g., for a quiz), which you can

reveal.

After having selected the function, the hidden information appears.

•

Press to resume the normal Teletext operation.

Time Page*

*depending on availability of service

You can call up a time-coded page - such as an alarm page - at a time specified

by you.

After having selected the function a sub menu is displayed.

1 Select On using 4 or $. Push to ” to enter.

2 Enter the three digits of the desired page using the number buttons.

3 Enter the four digits of the desired time using the number buttons.

4 Press OK to store.

The time is displayed in the top left-hand corner of the screen.

At the requested time the page is displayed.

Teletext

Top / Bottom / Full

Text Clear

Reveal

Time Page

Select: Enter Menu:

Top: Bottom: Full: OK

Time Page

PAGE TIME

Select: Enter:

– – – - - : - -

Operation

14

Adjusting the picture and sound

Picture and sound are adjusted at the factory. You can however, adjust

them individually.

1 Press MENU.

Select the symbol

for Picture or for Sound using 4 or $.

Push to ” to enter.

The menu Picture or Sound Control is displayed.

2 Select the desired item using 4 or $. Push to ” to enter.

3 Adjust the selected item using 4, $, ” and “. Press OK to store.

Refer to the tables on this and the following page for more information.

4 Repeat steps 2 and 3 to adjust other items.

5 Press MENU to return to the normal TV screen.

Picture Control

Item Effect/Operation

Picture Mode $ Live (for live broadcasts)

Personal (for individual settings)

4 Movie (for movie broadcasts)

Contrast Less “” More

Brightness* Darker “” Brighter

Colour* Less “” More

Hue** Reddish “” Greenish

Sharpness* Softer “” Sharper

Reset Resets picture to the factory preset levels

AI 4 Off: normal

(Artificial Intelligence) $ On: Automatic optimization of contrast level

according to the TV signal

Noise Reduction 4 Off: Normal

$ On: Reduces picture noise in case of a weak

broadcasting signal

Digital Mode $ Normal: 100 Hz.

Digital+: 100 Hz plus line flicker reduction

4 Advanced: Digital+ plus smoothing of motions

* Only if Personal is selected in Picture Mode

** Only available for NTSC colour signal (e.g. US video tapes)

Picture Adjustment

Select Mode: Enter:

Picture Mode

Contrast

Brightness

Colour

Sharpness

Reset

AI

Noise Reduction

Digital Mode

Personal

On

Normal

Picture Mode

Live

Personal

Movie

Contrast

AI

On

Off

Noise Reduction

On

Off

Digital Mode

Normal

Digital+

Advanced

The TV consists of a menu system which is based on a series of user friendly on-screen displays and menus. These

displays will help you get the most from your TV, helping you to change picture and sound settings, to alter the size of the

TV picture and to rearrange the TV channels etc.

Using the TV menu system

Operation

15

Sound Control

Item Effect/Operation

Equaliser mode Select between the following sound settings

$ Personal

Vocal

Jazz

Rock

Pop

4 Flat (fixed setting, cannot be adjusted)

Equaliser adjustment

You can adjust the mode selected in Equaliser

mode by cutting and boosting of 5 selected

frequency bands.

Only the changes made in Personal can be stored,

the others return to factory setting.

•

Select the desired bar using ” or “, adjust using 4

and $.

Press OK to store.

Balance ” More right

“ More left

Loudness $ Off: Normal

4 On: For music broadcasts

Space $ Off: Normal

4 On: Special accoustic effect

Auto Volume Control 4 On: volume level of the channels will stay the same

independent of the broadcast signal

(e.g. in case of advertisements)

$ Off: volume level changes according to the

broadcast signal

Dual Sound For a bilingual broadcast:

$ A for channel 1

4 B for channel 2

For a stereo broadcast:

$ Mono

4 Stereo

In case of a NICAM stereo broadcast the indication

NICAM appears briefly on the screen.

Headphones

2 Volume Less “ ” More

2 Dual Sound For a bilingual broadcast:

$ A for channel 1

4 B for channel 2

Operation (TV menu system):

Equaliser Adjustment

Sel: Adjust: Confirm:OK

Personal

+

0

–

120 150 1,5K 5 K 10 K

Audio Adjustment

Equaliser Mode

Equaliser

Adjustment

Balance

Loudness

Space

Auto Vol. Control

Dual Sound

Volume

Dual Sound

Personal

Mono

Off

On

Mono

Personal

Vocal

Jazz

Rock

Pop

Flat

Select Mode: Confirm: OK

Off

Loudness

Off

On

Balance

Space

Off

On

Volume

Dual Sound

A

B

Dual Sound

Mono

Stereo

Auto Vol. Control

Off

On

16

Using the Features menu

1 Press the MENU button on the remote control. Select the symbol using $.

Push to z to enter.

2 Select the desired menu item using $. Push to z to enter.

3 Select the desired setting using 4 or $.

4 Store by pressing OK.

5 Press MENU to return to the normal TV screen.

Operation (TV menu system):

Features

Item Effect/Operation

Auto Format* 4 Off: Size of picture does not automatically adjust.

*only for aerial signal Normal: Size of picture automatically adjusts

according to information from broadcaster.

$ Full: The TV can automatically adjust the picture

size to eliminate any dark areas on the TV

picture (as shown below):

Format Correction* 4 On: Smart mode is selected automatically for

*only if Auto Format is 4:3/14:9 broadcasts

set to ‘Normal‘ or ‘Full‘ $ Off: 4:3/14:9 is selected

Sleep Timer You can select a time period after which the TV

switches itself into standby mode

4 Off

10 min.

20 min.

.

$ 90 min.

Parental Lock 4 Off: Normal mode

$ On: TV can only be switched on out of

standby-mode using the Remote Commander,

the buttons on the TV do not work.

AV2 Source You can select the source to be output from the

Scart connector

Y2/j2. In this way you can

record from this socket while watching another

source.

4 TV audio/video signal from the aerial ˘

AV1 audio/video signal from Scart 1

AV2 audio/video signal from Scart 2

$ AV3 audio/video signal from connectors on top or

bottom of rear of TV.

Features

Auto Format

Format Correction

Sleep Timer

Parental Lock

AV 2 Source

Off

TV

Select: Enter:

Off

Normal

Full

Auto Format

Off

Normal

Full

Format Correction

Off

On

10 min

Sleep Timer

Parental Look

Off

On

AV 2 Source

AV 1

AV 2

AV 3

TV

17

Changing the screen mode

When Auto Format in the Features menu is preset to ”Normal“ or “Full“, the

TV set automatically selects the detected screen format. Screen mode, however,

lets you select the screen format of your choice.

•

Press the button on the remote control repeatedly to get one of the

following formats:

Smart imitation of wide screen effect for 4:3 broadcasts, parts of the top and

bottom of the picture are cut off

4:3 conventional 4:3 aspect ratio, full picture information

14:9 compromise between 4:3 and 16:9 aspect ratios

Zoom imitation of wide screen effect for letterboxed movies

Wide for 16:9 broadcasts

In Zoom, Smart and 14:9 modes parts of the top and the bottom of the screen

are cut off. Using 4 and $ you can adjust the position of the image onscreen to

e.g. read subtitles. Press OK to confirm.

Operation (TV menu system):

Smart

Zoom

Wide

18

Sorting TV channels

After tuning in TV channels, you may wish to rearrange the order of the channels.

1 Press the MENU button on your remote control. Select the symbol

using $.

Push to ” to enter.

2 Select Programme Sorting using $. Push to ” to enter.

3 Select the programme position of the channel you wish to sort using 4 or $.

Push to ” to enter.

4 Move the channel to the new programme position using 4 or $. Store by

pressing OK.

The channel is now at the new position. The other programme positions

move accordingly.

5 To sort other programme positions repeat steps 3 to 4.

6 Press MENU to return to the normal TV screen.

Manually tuning-in channels

Use this function to preset channels or a video input source one by one to

programme positions of your choice.

1 Press the MENU button on the remote control. Select the symbol

using $.

Push to ” to enter.

2 Select Installation using $. Push to ” to enter.

Select Manual Programme Preset using $. Push to ” to enter.

3 Select the programme position by pushing to 4 or $. Push twice to ”.

The column SYS is highlighted.

4 Select the TV system using 4 or $. Push to ” to enter.

Available TV systems are I for Ireland or EXT for a video input source (please

go to step 5c after selecting EXT).

5 Select your method for the channel tuning using 4 or $. Push to ” to enter.

You have the choice between C for a terrestrial channel, S for a cable channel or

F for direct frequency input.

6a Direct Channel Input

For channel numbers input a two digit number, for the channel frequency a

three digit number.

•

Select the two or three digits by using the number buttons 0 to 9.

•

To start the search and to store the channel, press the OK button.

•

To preset other channels repeat steps 3 to 6a.

b Channel search (SEARCH)

Use Search if you do not know the channel number or frequency

•

Start the search for the next available channel by pushing to $.

•

Store the channel by pressing OK or continue the search by pushing again to $.

•

To search for other channels repeat steps 3 to 6b.

c For video input sources (EXT)

•

Select the Video Input source using 4 or $.

•

Store your selection by pressing OK.

•

To allocate other sources repeat steps 3 to 5c.

6 Press MENU to return to the normal TV screen.

Programme Sorting

Select Prog: Confirm:

PROG CH LABEL

Programme Sorting

Select Position: Move: OK

C03 TV 5

PROG CH LABEL

1

2

3

4

5

6

7

8

9

10

11

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

TV 5

PRO 7

EU-SP

SWF

RTL

SAT

MDR

DDI

DSF

RTL 2

KAB 1

C03

C05

C07

C08

C09

C11

C12

C13

C14

C15

C16

TV 5

PRO 7

EU-SP

SWF

RTL

SAT

MDR

DDI

DSF

RTL 2

KAB 1

1

2

3

4

5

6

7

8

9

10

11

Installation

Select: Enter:

Language/Country

Manual Programme Preset

Further Programme Preset

RGB Set Up

Picture Rotation

Speaker Configuration

Personal ID

O

- - - - - - -

Manual Programme Preset

Select: Enter:

PROG CHSYSSKIP LABEL

C09

C10

BBC1

BBC

B/G

Off

1

2

3

4

5

6

7

8

9

10

11

PROG CHSYS

Off

SKIP LABEL

1

B/G

L

I

D/K

EXT

Internal

PROG SYS

Off

SKIP LABEL

1 I

CH

C

S

F

PROG CHSYS

Off

SKIP LABEL

0 EXT

AV1

AV2

AV3

AV1

PROG SYS

Off

SKIP LABEL

1 I

CH

03

SEARCH

Operation (TV menu system):

Sivu latautuu...

Sony KV-28FC60Z Ohjekirja

Sony KV-28FC60Z Ohjekirja

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat