Yamaha TSX-140 Omistajan opas

Kategoria
Radios
Tyyppi
Omistajan opas
TSX-140
© 2010 Yamaha Corporation
Printed in China
WY55190
G
DESKTOP AUDIO SYSTEM
SYSTEME AUDIO DESKTOP
TSX-140
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
i En
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power
cable disconnected from a wall outlet or this unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press to set the system to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this
unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like. When you dispose
of batteries, follow your regional regulations.
22 Be sure to use the AC adaptor supplied with this unit.
Using an AC adaptor other than the one provided
may cause fire or damage to this unit.
23 Excessive sound pressure from earphones and
headphones can cause hearing loss.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
1 En
English Français Deutsch Svenska Italiano Español Nederlands Русский
NAMES OF PARTS AND THEIR
FUNCTIONS...............................................2
ADJUSTING THE CLOCK..........................5
LISTENING TO iPod ..................................6
LISTENING TO CD AND USB DEVICE .....7
LISTENING TO RADIO STATIONS ...........8
LISTENING TO EXTERNAL SOURCE ......8
USING ALARM FUNCTION .......................9
SHUFFLE/REPEAT PLAYBACK ............. 12
USING SLEEP FUNCTION...................... 12
TONE CONTROL..................................... 12
TROUBLESHOOTING ............................. 13
NOTES ON DISCS AND USB DEVICES
................................................................. 16
SPECIFICATIONS ...................................17
CONTENTS
X Features
iPod/iPhone, CD, USB device, radio and external device using AUX are playable.
– Synchronization iPod/iPhone with iTunes through this unit is available (iPod iTunes Sync function).
Providing comfortable wake-up by the music set with your preferred volume with alarm function.
Music, beep sound, or both can be set as alarm sound (IntelliAlarm function).
Storing/calling your five favorite radio stations easily.
Bass, middle, treble can be controlled depending on your favorite.
X About this manual
“iPod” described in this manual may also refer to “iPhone”.
This manual describes how to operate this unit using buttons on the unit. Some of these operations are also
available using the remote control.
X Supplied accessories
1
2
3
Remote
control
AC
adaptor
Power
cable
Indoor FM
antenna
(DC 15 V, more
than 2.56 A
Model number:
EADP-38EB A or
NU40-8150266-I3)
USB cap
X Using the remote
control
Within 6 m
(20’)
Battery insulation
sheet: Remove
before using.
(With CR2025
battery)
Dock
cover
Keep the USB cap out
of the reach of
children, so that it is
not mistakenly
swallowed.
Note
X Replacing the battery in the remote
control
While pushing the release tab in direction , slide out the
battery holder in direction .
CR2025
battery
2 En
PREPARATION
X Top panel
1 iPod dock: Set an iPod.
2 USB port ( P. 7)
When the USB device is not in use, set the USB cover to
protect the connector.
3 : Press to turn the system on/off.
Time is displayed even when the system is off.
y
Press and hold on the top of the unit for more than 3
seconds to set the system to power save mode. All the
information on the front panel display is not displayed
in power save mode. This can reduce power
consumption. To cancel power save mode, press on
the top of the unit.
Even in system off/standby mode, the alarm function is
available.
4 DIMMER:
Setting brightness of the front panel
A (auto) 3 (brightest) 2 1 (darkest) back to A
y
When A (auto) is set, the brightness of the front panel is
adjusted automatically depending on the brightness of the
room.
5 ALARM: Alarm on/off ( P. 11)
6 SET: Alarm setting ( P. 9)
7 SNOOZE/SLEEP ( P. 11, 12)
8 TUNING ( P. 8)
9 Audio control buttons: Skip, search backward/
forward, play/pause, stop
0 : Ejecting the CD.
A Disc slot ( P. 7)
NAMES OF PARTS AND THEIR FUNCTIONS
Dock
Adaptor
Set your iPod in the iPod dock.
y
An iPod is charged when set in the iPod dock. During power save mode, the iPod is not
charged.
Be sure to use a dock adaptor that is compatible with your iPod. If you do not use the
adaptor or the adaptor is not compatible, the connection could be loose or poor, which
could cause damage to the connector.
If an iPod in protective case is connected by force, the connector may be damaged.
Remove the protective case before connection.
When the iPod is not in use, set the dock cover to protect the connector.
Notes
Note
NAMES OF PARTS AND THEIR FUNCTIONS
3 En
English
X Front panel
1 Front panel display: Displays the clock and various
information.
2 Preset indicator: Shows preset radio station
number ( P. 8)
3 PLAY indicator
Shuffle indicator
Repeat indicator
: Shows playback status. ( P. 10, 12)
4 Source indicator: Shows selected source.
5 Illumination sensor: Measuring surrounding
illuminance. Do not cover this sensor.
6 SOURCE: Change sources.
7 VOLUME: Volume control
8 PRESET
(During playing data CD/USB): Change folders
(During receiving radios): Select the preset radio
station. ( P. 8)
9 HEADPHONES: Connect headphones.
0 MEMORY: Memories preset radio station. ( P. 8)
A EQ: Tone control ( P. 12)
B SYNC: iPod iTunes Sync function on/off
( P. 6)
NAMES OF PARTS AND THEIR FUNCTIONS
4 En
X Rear panel (Connecting antenna)
1 FM antenna terminal: Connect the supplied indoor
FM antenna.
2 GND: Connect the cable core of the Indoor FM
antenna (see below).
3 AUX: Connect an external device. ( P. 8)
4 USB FOR SYNC.: Connect to PC. ( P. 6)
5 15V : Connect supplied AC adaptor and power
cable.
6 CLOCK: Adjust the clock. ( P. 5)
7 ALARM TYPE: Set alarm type of IntelliAlarm
function. ( P. 9)
8 Indoor FM antenna (supplied)
The antenna should be stretched out.
If you use an outdoor antenna instead of the supplied FM
antenna, reception will be better.
If radio reception is poor, change the height, direction, or
placement of the antenna.
Connecting antenna to the GND terminal
It is recommended to connect the antenna to the GND terminal before connecting to the FM antenna terminal.
Notes
1
2
3
4
1Remove insulation and
twist the edge of the
cord.
2Fully screw down the GND terminal.
3Wind the cord around the GND terminal. Make sure
the cord is wound inside of the ring part.
4Tighten the GND terminal
taking care not to slip the cord
off from the terminal.
Ring
ADJUSTING THE CLOCK
5 En
English
X Remote control
1 Infrared signal transmitter
2 : System on/off
3 Source buttons: Change sources.
4 FOLDER (during playback): When source contains
folders, change played folder.
PRESET (during receiving radio): Select the preset
radio station ( P. 8)
5 (Shuffle), (Repeat) ( P. 12)
6 : Stop playback.
7 , (during playback): Skip and search
backward/forward
TUNING (during receiving radio): Tuning radio
( P. 8)
8 : Play/pause
9 MUTE: Mute/resume the sound.
0 VOLUME: Volume control
A SNOOZE/SLEEP: Snooze/sleep setting
( P. 11, 12)
B ALARM: Alarm on/off ( P. 11)
C SYNC: iPod iTunes Sync function on/off
( P. 6)
iPod control buttons
ADJUSTING THE CLOCK
1 Set CLOCK to SET.
2 Set the time.
Set the time with PRESET.
3 Set CLOCK to LOCK to
complete.
At the time LOCK is set, it will be 00
second and time count starts.
y
On step 2, you can copy the time of iPod
instead of setting time manually by setting the
iPod to the iPod dock. If iPod is already in the
iPod dock when CLOCK is set to SET, the
time in the iPod is not copied to this unit.
•Press SNOOZE/SLEEP to switch between
the 12 and 24 hour clock display.
The time settings are lost about one week after
unplugging the unit.
1 2
Rear panel
Front panel
Note
3
6 En
OPERATION
For details on compatible iPod models, refer to “SPECIFICATIONS” ( P. 17).
You can synchronize your iPod with your iTunes through this unit.
LISTENING TO iPod
Listening to iPod
1 Set your iPod in the iPod dock.
2 Set SOURCE to iPod.
3 Play the iPod.
Playback operations are available with
the remote control, iPod and this unit.
y
You can remove the iPod whenever you
want.
When music/video in the iPod is played
back, this unit turns the system on
automatically and plays back the iPod
even if the unit is system off.
1 2
Front panel
Synchronizing with iTunes (iPod iTunes Sync function)
1 Connect this unit to PC with
commercially available USB 2.0
cable (A/Mini-B).
Use USB 2.0 cable shorter than 2 m (6.6').
2 Set your iPod in the iPod dock.
3 Turn the system on.
SYNC indicator located on the left
side of the SYNC lights up.
4 Press and hold SYNC.
SYNC indicator flashes. After that,
synchronize to iPod with iTunes using
PC. For details on synchronization,
refer to the manual of iPod.
5 Press and hold SYNC to
complete after disconnecting the
iPod on iTunes.
y
During synchronizing, source other than iPod
can be played back.
During synchronizing, system cannot be
turned off.
Do not remove the iPod, USB cable, AC
adaptor and power cable during synchronizing.
During synchronizing, alarm function does
not work.
Rear panel
1 2
Note
Notes
Top panel
3
4 5
Press and
hold
Press and
hold
Synchronize
Front panel
7 En
English
y
If button on the top panel is pressed during playback, next time playback starts from the beginning of the track you
listened to last time. If button is pressed again while playback is stopped, next time playback starts as follows:
For audio CD: from the first track of the CD.
For data CD/USB device: from the first track of the folder contains the track you listened to last time.
For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” ( P. 16).
This unit automatically turns off the system 60 minutes after CD/USB device playback is stopped.
LISTENING TO CD AND USB DEVICE
X Listening to CD
1 Set SOURCE to CD.
2 Insert a CD.
Playback starts automatically.
Playback operations are available with
the remote control and this unit.
Insert the CD with the label side facing
toward the front of the unit.
X Listening to USB device
1 Set SOURCE to USB.
2 Connect a USB device.
Playback starts automatically.
Playback operations are available with
the remote control and this unit.
y
You can remove your USB device
whenever you want.
USB playback order is determined as
follows:
Folders are played in alphabetical order of
the first three characters in the folder name.
Other characters come after the alphabet.
Files are played in recording order.
1 2
Front panel
Note
1 2
Front panel
X Display information
Track or folder and file number appears for a while when playback starts.
X Skipping folder for data CD/USB device
Select the folder with PRESET
when data CD/USB device is
played back.
Playing back audio CD
Track number
Playing back data CD/USB device
Folder number
File number
Front panel
8 En
X Presetting radio stations
You can store your favorite 5 radio stations with the preset function.
LISTENING TO RADIO STATIONS
X Tuning radio stations
1 Set SOURCE to FM.
2 For automatic tuning, press and
hold TUNING.
For manual tuning, press
TUNING repeatedly.
If you tune to a station manually, the sound
is monaural.
1 Tune into a favorite radio station.
2 Press MEMORY.
3 Select the PRESET number you
want to store to.
y
To cancel the preset, press TUNING again.
4 Press MEMORY to complete.
X Selecting preset radio stations
1 Set SOURCE to FM.
2 Select the preset radio station
with PRESET.
LISTENING TO EXTERNAL SOURCE
1 Connect your portable audio
device to AUX using a
commercially available 3.5 mm
(1/8 in) mini plug cable.
Turn down the volume of this unit and your
portable audio device before connection.
2 Set SOURCE to AUX.
3 Start playback on the connected
portable audio device.
1 2
Top Panel
Front panel
Note
1 2
Top Panel
Front panel
3
Front panel
4
Front panel
1 2
Front panel
1 2
Rear Panel Front panel
Note
9 En
English
This unit can play back your favorite music and/or beep sound at the set time. The alarm function
(IntelliAlarm) has following features.
This unit has 3 alarm types combining music and beep sound:
Alarm source played back at the set time can be selected from iPod, audio CD, data CD, USB
device, and radio. Depending on the source, followings also can be selected:
You can check the sound of the set alarm when making the alarm setting.
Snooze function is also available.
USING ALARM FUNCTION
Features of IntelliAlarm
SOURCE+BEEP
Selected audio source and the beep sound are played at the set time. Source playback begins to fade
in 3 minutes before the set time and the volume gradually increases to the set volume. Then, at the set
time, the beep sound is activated. This mode is recommended for a comfortable wake-up.
SOURCE
Selected source plays at the set time. Fade-in volume gradually increases to the set volume.
BEEP
Only beep sound is played back at the set time.
SOURCE Selectable item Function
iPod
Playlist The specified playlist is played back repeatedly. When you want to play
a playlist, create “ALARM Yamaha DTA” playlist in advance. Make
sure it is named exactly as shown here, with spaces between the words
and the same upper/lower case letters.
Resume play When the “ALARM Yamaha DTA” playlist is not in the iPod, the track
you listened to last time is resumed.
Audio CD
Track The Selected track is played back repeatedly.
Resume play The track you listened to last time is played back.
Data CD/USB
Folder The Selected folder is played back repeatedly.
Resume play The folder you listened to last time is played back.
FM
Preset The selected preset radio station is played.
Resume play The radio station you listened to last time is played.
Alarm setting
X Setting the alarm time and sound
1 Press SET.
Alarm indicator ( ) and setting
items flash.
2 Set the alarm time with
PRESET.
1 2
Top panel Front panel
USING ALARM FUNCTION
10 En
3 Set ALARM TYPE.
Select from SOURCE+BEEP,
SOURCE or BEEP. For the details
on alarm type, Refer to “Features of
IntelliAlarm ( P. 9)”.
4 Select SOURCE (as required).
When you select SOURCE+BEEP or
SOURCE, select source. A source
other than AUX can be selected.
5 Select a track, folder or radio
station (as required).
When the source is CD/USB/FM,
select a track, folder or radio station
for alarm with / .
y
When iPod is set as source, this unit plays
back “ALARM Yamaha DTA” playlist at
the set time. If the playlist is not in the
iPod, the track you listened to last time is
resumed.
When CD/USB is selected and “0” is set
as track/folder number, the track you
listened to last time is resumed.
When FM is selected and number of
preset indicator ( P. 3) is not displayed,
the radio station you listened to last time
is played.
When selected source is not set, setting on
step 5 cannot be set.
6 Set the alarm volume with
VOLUME.
y
When iPod or radio is selected, set alarm
can be played back by pressing . When
CD/USB is selected, set alarm can be
played back by pressing while
is flashing. Press to stop the
alarm.
7 Press SET to complete.
Alarm is set and the alarm indicator
( ) lights up.
3
Rear panel Front panel
4
(As required)
Note
65
Front panelTop panel
(As required)
7
Top panel
USING ALARM FUNCTION
11 En
English
At the set time, alarm sound plays back. During playback, operations below are available.
If source cannot be played back at the alarm time (ex. iPod is not set), beep sound is played back.
X Switching the alarm on/off
Switch on/off the alarm function.
y
When the alarm is on, the alarm indicator
( ) lights up and alarm time is displayed
for a while.
Operations during playing back alarm sound
X Using the snooze function
Press SNOOZE/SLEEP.
The alarm sound stops and resumes
after 5 minutes.
y
When SOURCE+BEEP is set, press
SNOOZE/SLEEP to stop the beep sound.
press SNOOZE/SLEEP again to stop the
source. After 5 minutes from the source is
stopped, the source with fading in and beep
sound resumes.
When the snooze function is activated, alarm
indicator flashes.
X Stopping the alarm
Press ALARM or .
y
Unless you stop the alarm, the alarm stops
after 60 minutes automatically.
The alarm function turns off when you
stop the alarm, but settings such as the
alarm time are saved for convenient use
next time. To set the alarm again, press
ALARM.
Top panel
Note
Top panel
Top panel Top panel
12 En
y
When source contains folders, folder shuffle/repeat can be selected.
For some iPod models, the shuffle and repeat functions may not be displayed or supported.
When iPod is played back, the setting order of shuffle and repeat depends on the iPod model.
SHUFFLE/REPEAT PLAYBACK
Shuffle playback
Press repeatedly
Remote control
Shuffle indicator lights up as follows.
CD/USB iPod
(Shuffle all songs
in the folder)
(All shuffle)
No display (Shuffle Off)
(Songs)
(Albums)
No display (Shuffle Off)
Repeat playback
Remote control
Repeat indicator lights up as follows.
CD/USB iPod
(Repeat all songs
in the folder)
(All repeat)
(Single repeat)
No display (Repeat Off)
(One)
(All)
No display (Repeat Off)
Press repeatedly
USING SLEEP FUNCTION
You can set the time to turn off the system automatically.
Select the sleep time.
You can set 30, 60, 90 or 120 minutes.
When the time is set, the sleep
function is set to on, and the sleep
indicator ( ) lights up.
y
To cancel the sleep, press SNOOZE/
SLEEP.
Top panel
Press repeatedly
TONE CONTROL
1 Press EQ during playback.
LOW, MID and HIGH light up.
2 Adjust the tone with LOW, MID
and HIGH.
3 Press EQ to complete.
1 2
Front panel
Front panel
3
13 En
English
ADDITIONAL INFORMATION
In case of a problem with the unit, check the following list first. If you cannot solve your problem with the
suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest
authorized Yamaha dealer or service center.
TROUBLESHOOTING
General
Problem Cause Solution
The speakers make no
sound.
The volume may be set to the minimum
level.
Adjust the volume level.
The source may be incorrect. Select the correct source.
Headphones are connected. Remove the headphones.
Sound suddenly turns off.
The sleep ( P. 12) may be set. Turn on the system and play the source
again.
Sound is cracked/distorted
or there is abnormal noise.
Input source volume is excessive, or
volume of this unit is excessive
(especially Bass).
Adjust volume with VOLUME, or adjust
Bass with EQ ( P. 3, 12).
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The system turns on but
immediately shuts off.
A digital or high-frequency
equipment produces noises.
The unit may be placed too close to the
digital or high-frequency equipment.
Place the unit farther away from the
equipment.
The clock setting has been
cleared.
The unit is left more than one week after
you disconnect the power cable from the
wall outlet.
Plug the power cable into the wall outlet
firmly, and set the clock again ( P. 5).
iPod does not play back at
the alarm time even if
SOURCE is set to iPod.
The iPod is not set in the iPod dock. Set the iPod in the iPod dock ( P. 2).
ALARM TYPE is set to BEEP. Set ALARM TYPE to SOURCE+BEEP or
SOURCE ( P. 9).
Clock flashes and the unit
cannot be operated.
CLOCK on the rear panel is set to SET,
and this unit is in clock setting mode.
Set CLOCK to LOCK.
TROUBLESHOOTING
14 En
iPod
Problem Cause Solution
No sound
The iPod is not set in the iPod dock
firmly.
Set the iPod firmly.
Earphones are connected. Remove the earphones.
The iPod software version has not been
updated.
Download the latest iTunes software to
update the iPod software version to the
latest.
The iPod does not charge up.
The iPod is set in the iPod dock
improperly.
Remove the iPod from the unit, and then set
it in the iPod dock again ( P. 2).
The system is set to power save mode
( P. 2).
Press to cancel the power save mode.
Flashing iPod indicator twice
is repeated 3 times after
connecting the iPod.
The iPod being used is not supported by
the unit.
Use a supported iPod ( P. 17).
Synchronization with iTunes
cannot be performed using
this unit.
Depending on the PC or USB cable,
signal damping is increased and the
connection might be failed.
Use shorter USB 2.0 cable.
Disc playback
Problem Cause Solution
Disc cannot be inserted.
The system is set to power save mode
( P. 2).
Press to cancel the power save mode.
Some button operations do
not work.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit ( P. 16).
Playback does not start
immediately after pressing
.
The disc may be dirty. Wipe the disc clean.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit ( P. 16).
If the unit was moved from a cold to
warm place, condensation may have
formed on the disc reading lens.
Wait for an hour or two until the unit
adjusts to the room temperature, and try
again.
CD indicator repeats flashing
twice 3 times, and the disc is
unloaded.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit ( P. 16).
The disc may be dirty. Wipe the disc clean.
The disc is loaded back to front. Insert a disc facing the label side to near
side.
The disc does not contain playable files. Use a disc contains playable files
( P. 16).
“Err” is displayed in the front
panel display after loading a
disc.
An error occurs in the unit. Unload the disc with .
TROUBLESHOOTING
15 En
English
USB device playback
Problem Cause Solution
MP3/WMA file in the USB
device does not play.
The USB device is not recognized. Turn off the system and reconnect the USB
device to the unit.
Connect an AC adapter if supplied with the
device.
If the solutions above do not resolve the
problem, the USB device is not playable on
the unit.
Flashing USB indicator twice
is repeated 3 times after
connecting a USB device.
An incompatible USB device is
connected to the unit.
Turn off the system and reconnect the USB
device to the unit. If it does not resolve the
problem, the USB device is not playable on
the unit.
The USB device does not contain
playable files.
Use a USB device contains playable files
( P. 16).
“Err” is displayed in the front
panel display after
connecting a USB device.
An incompatible USB device is
connected to the unit.
Turn off the system and reconnect the USB
device to the unit. If it does not resolve the
problem, the USB device is not playable on
the unit.
An overcurrent is detected.
Radio reception
Problem Cause Solution
Too much noise during
stereo broadcast.
The antenna may be connected
improperly.
Make sure the antenna is connected
properly ( P. 4).
The radio station you selected may be far
from your area, or the radio wave
reception is weak in your area.
Try manual tuning to improve the signal
quality ( P. 8) or use a multi-channel
outdoor antenna.
Even with an outdoor
antenna, radio wave
reception is weak. (Sound is
distorted.)
Multipath reflection or other radio
interferences may have occurred.
Change the height, direction, or placement
of the antenna.
Remote control
Problem Cause Solution
The remote control does not
work properly.
The remote control may be operated
outside its operation range.
For information on the remote control
operation range, refer to “Using the remote
control” ( P. 1).
The remote control sensor on the unit
may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the
unit.
The battery may be worn out. Replace the battery with a new one.
There are obstacles between the sensor of
the unit and the remote control.
Remove the obstacles.
16 En
This unit is designed for use with audio CD, CD-R*,
and CD-RW* with the logos followings.
* ISO 9660
y
This unit can play back discs bearing any of the logo marks
above. A disc logo mark is printed on the disc and the disc
jacket.
Do not load any other type of disc into this unit. Doing so
may damage this unit.
CD-R/RW cannot be played back unless finalized.
Some discs cannot be played back depending on the disc
characteristics or recording conditions.
Do not use any non-standard shaped discs such as a heart-
shaped disc.
Do not use discs with many scratches on their surface.
Do not touch the surface of
the disc. Hold a disc by its
edge (and the center hole).
Do not use a pencil or
pointed marker to write on
the disc.
Do not put a tape, seal, glue, etc., on a disc.
Do not use a protective cover to prevent scratches.
Do not load more than one disc into this unit at one time.
This can cause damage to both this unit and the discs.
Do not insert any foreign objects into the disc slot.
Do not load a cracked, warped, or glued disc.
Do not expose a disc
to direct sunlight,
high temperature,
high humidity, or a
lot of dust.
If a disc becomes
dirty, wipe it with a
clean, dry cloth from
the center out to the
edge. Do not use
record cleaner or
paint thinner.
To avoid
malfunction, do not
use a commercially
available lens
cleaner.
This unit supports USB mass storage class devices
(e.g., flash memories or portable audio players) using
FAT16 or FAT32 format.
Some devices may not work properly even if they meet the
requirements.
Do not connect devices other than USB mass storage class
devices (such as USB chargers or USB hubs), PCs, card
readers, an external HDD, etc.
Yamaha will not be held responsible for any damage to or
data loss on the USB device occurring while the device is
connected to this unit.
Playability of and power supply to all kind of USB devices
are not guaranteed.
The unit can play back:
** Both constant and variable bitrates are supported.
The maximum numbers of files/folders that can be
displayed on the unit are as follows.
Copyright-protected files cannot be played back.
NOTES ON DISCS AND USB DEVICES
Disc information
Handling a disc
Notes
Caution
USB device information
About MP3 or WMA files
File Bitrate (kbps)
Sampling
frequency (kHz)
MP3
8 - 320** 16 - 48
WMA
16 - 320** 22.05 - 48
Data CD USB
Maximum total number of file
512 9999
Maximum folder number
255 128
Maximum file number per folder
511 255
Notes
Notes
17 En
English
X PLAYER SECTION
iPod (Digital connection)
Made for ...... iPod touch (1st, 2nd, 3rd, and 4th generation)
iPod classic
iPod nano (2nd, 3rd, 4th, 5th, and 6th generation)
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
CD
Media........................................................... CD, CD-R/RW
Audio format ................................. Audio CD, MP3, WMA
Laser
Type.............................Semiconductor laser GaAs/GaAlAs
Wave length .............................................................790 nm
Output Power .............................................................7 mW
USB
Audio format ....................................................MP3, WMA
AUX
Input connector........... 3.5 mm (1/8 in) STEREO mini Jack
X AMPLIFIER SECTION
Maximum output power .................................15 W + 15 W
(6 Ω 1 kHz, 10% THD)
Headphones ............................ 3.5 mm STEREO mini Jack
(Adaptive Impedance 16 to 32 Ω)
X TUNER SECTION
Tuning range
FM...................................................87.50 to 108.00 MHz
X GENERAL
Power Supply ...........................AC 100 to 240 V, 50/60 Hz
Power consumption ..................................................... 20 W
System off consumption............................................. 1.5 W
Power save consumption .................................0.5 W or less
USB FOR SYNC. terminal ..............................USB mini-B
Dimensions (W × H × D) ...................399 × 181 × 137 mm
(153/4 × 71/8 × 53/8 in)
Weight .........................................................3.2 kg (7.1 lbs.)
Specifications are subject to change without notice.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt
to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam. When this unit is plugged into
the wall outlet, do not place your eyes close to the opening of
the disc tray and other openings to look into inside.
iPod, iPhone
“Made for iPod,” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
iPhone, iPod, iPod classic, iPod nano, iPod touch and iTunes
are trademarks of Apple Inc., registered in the U.S. and other
countries.
SPECIFICATIONS
The laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
i Fr
1 Pour utiliser l’appareil au mieux de ses possibilités,
lisez attentivement ce mode d’emploi. Conservez-le
soigneusement pour référence.
2 Installez cet appareil dans un endroit frais, bien aéré,
sec et propre - à l’abri de la lumière du soleil, des
sources de chaleur, des vibrations, des poussières, de
l’humidité et du froid. Pour une aération correcte,
tenez compte des distances minimales suivantes.
Au-dessus : 15 cm
À l’arrière : 10 cm
Sur les côtés : 10 cm
3 Placez l’appareil loin des équipements, moteurs et
transformateurs électriques, pour éviter les
ronflements parasites.
4 N’exposez pas l’appareil à des variations brutales de
température, ne le placez pas dans un environnement
très humide (par exemple dans une pièce contenant
un humidificateur) car cela peut entraîner la
condensation d’humidité à l’intérieur de l’appareil
qui elle-même peut être responsable de décharge
électrique, d’incendie, de dommage à l’appareil ou de
blessure corporelle.
5
Evitez d’installer l’appareil dans un endroit où des
objets peuvent tomber, ainsi que là où l’appareil pourrait
être exposé à des éclaboussures ou des gouttes d’eau.
Sur le dessus de l’appareil, ne placez pas :
d’autres appareils qui peuvent endommager la
surface de l’appareil ou provoquer sa décoloration.
des objets se consumant (par exemple, une bougie)
qui peuvent être responsables d’incendie, de
dommage à l’appareil ou de blessure corporelle.
des récipients contenant des liquides qui peuvent
être à l’origine de décharge électrique ou de
dommage à l’appareil.
6
Ne couvrez pas l’appareil d’un journal, d’une nappe,
d’un rideau, etc. car cela empêcherait l’évacuation de la
chaleur. Toute augmentation de la température
intérieure de l’appareil peut être responsable d’incendie,
de dommage à l’appareil ou de blessure corporelle.
7 Ne branchez pas la fiche du câble d’alimentation de
l’appareil sur une prise secteur aussi longtemps que
tous les raccordements n’ont pas été effectués.
8 Ne pas faire fonctionner l’appareil à l’envers. Il
risquerait de chauffer et d’être endommagé.
9 N’exercez aucune force excessive sur les
commutateurs, les boutons et les cordons.
10 Pour débrancher la fiche du câble d’alimentation au
niveau de la prise secteur, saisissez la fiche et ne tirez
pas sur le cordon.
11 Ne nettoyez pas l’appareil au moyen d’un solvant
chimique, ce qui pourrait endommager la finition.
Utilisez un chiffon sec et propre.
12 N’alimentez l’appareil qu’à partir de la tension
prescrite. Alimenter l’appareil sous une tension plus
élevée est dangereux et peut être responsable
d’incendie, de dommage à l’appareil ou de blessure
corporelle. Yamaha ne saurait être tenue responsable
des dommages résultant de l’alimentation de
l’appareil sous une tension autre que celle prescrite.
13 Pour empêcher tout dommage causé par les éclairs,
déconnectez la câble d’alimentation et toute antenne
extérieure de la prise murale pendant un orage.
14 Ne tentez pas de modifier ni de réparer l’appareil.
Consultez le service Yamaha compétent pour toute
réparation qui serait requise. Le coffret de l’appareil
ne doit jamais être ouvert, quelle que soit la raison.
15 Si vous envisagez de ne pas vous servir de l’appareil
pendant une longue période (par exemple, pendant
les vacances), débranchez la fiche du câble
d’alimentation au niveau de la prise secteur.
16 Lisez la section intitulée « GUIDE DE
DÉPANNAGE » où figurent une liste d’erreurs de
manipulation communes avant de conclure que
l’appareil présente une anomalie de fonctionnement.
17 Avant de déplacer l’appareil, appuyez sur pour
éteindre le système puis débranchez la fiche du câble
d’alimentation au niveau de la prise secteur.
18 La condensation se forme lorsque la température
ambiante change brusquement. En ce cas, débranchez
la fiche du câble d’alimentation et laissez l’appareil
reposer.
19 La température de l’appareil peut augmenter en
raison d’une utilisation prolongée. En ce cas, coupez
l’alimentation de l’appareil et laissez-le au repos pour
qu’il refroidisse.
20 Installez cet appareil à proximité de la prise secteur et
à un emplacement où la fiche du câble d’alimentation
est facilement accessible.
21 Les piles ne doivent pas être exposées à une chaleur
extrême, par exemple au soleil, à une flamme, etc.
Lors de la mise au rebut des piles, suivez vos
réglementations locales.
22 Utilisez l’adaptateur secteur fourni avec cet appareil.
L’emploi de tout autre adaptateur secteur peut causer
un incendie ou endommager l’appareil.
23 Une pression excessive du son par les écouteurs et le
casque d’écoute peut entraîner la perte de l’ouïe.
ATTENTION : VEUILLEZ LIRE CE QUI SUIT AVANT D’UTILISER
L’APPAREIL.
Cet appareil n’est pas déconnecté du secteur tant qu’il reste
branché à la prise de courant, même si l’appareil en soi est
éteint par la touche . Dans cet état, l’appareil consomme
une très faible quantité de courant.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE
DÉCHARGE ÉLECTRIQUE, N’EXPOSEZ PAS CET
APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
ATTENTION
Danger d’explosion si la pile n’est pas remplacée
correctement. La remplacer par une pile de type identique
ou équivalent.
Il y a un risque possible de création d’interférences,
visibles sur les images en couleurs si cet appareil est placé
à côté d’un téléviseur à tube cathodique (tube de Braun).
Dans ce cas, éloigner l’unité du téléviseur.
1 / 1

Yamaha TSX-140 Omistajan opas

Kategoria
Radios
Tyyppi
Omistajan opas