Parkside BMH 1100 Käyttö ohjeet

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:39 Uhr Seite 1

18

30

42

54

67

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:39 Uhr Seite 2

3

1

2

3

13

3

4

7

8

9

10

6

4

1

2

4

5

11

12

14

16

13

15

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 3

4

6 7

2

14

5

2

14

15

8 9

16

7

10

9

8

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 4

5

10

A

5

C

E

D

B

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 5

GB/IE/

CY

6

Table of contents: Page

1. Introduction .............................................................................8

2. Safety regulations ...................................................................8-10

3. Layout .....................................................................................10

4. Items supplied.........................................................................11

5. Proper use ..............................................................................11

6. Technical data ........................................................................11-12

7. Before starting the equipment.................................................12-13

8. Starting up...............................................................................13-14

9. Replacing the power cable ....................................................14

10. Cleaning, maintenance and ordering of spare parts...............14

11. Disposal and recycling............................................................15

12. Declaration of conformity........................................................16

13. Guarantee Certificate .............................................................17

The reprinting or reproduction by any other

means, in whole or in part, of documentation

and papers accompanying products is

permitted only with the express consent of ISC

GmbH.

Technical changes subject to change

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 6

GB/IE/

CY

7

Caution - Read the operating instructions to reduce the risk of inquiry

Wear ear-muffs.

The impact of noise can cause damage to hearing.



Wear a breathing mask.

Dust which is injurious to health can be generated when working on wood and other

materials. Never use the device to work on any materials containing asbestos!



Wear safety goggles.

Sparks generated during working or splinters, chips and dust emitted by the device

can cause loss of sight.



Select between the individual functions only when the equipment is

at a standstill. If you fail to observe this point, the equipment may be

damaged.

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 7

GB/IE/

CY

8

1. Introduction

 Important!

When using equipment, a few safety

precautions must be observed to avoid injuries

and damage. Please read the complete

operating manual with due care. Keep this

manual in a safe place, so that the information

is available at all times. If you give the

equipment to any other person, give them

these operating instructions as well.

We accept no liability for damage or accidents

which arise due to non-observance of these

instructions and the safety information.

2. Safety regulations

 CAUTION!

Read all safety regulations and

instructions.

Any errors made in following the safety

regulations and instructions may result in an

electric shock, fire and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

The term “electric tool” used in the safety

regulations refers to electric tools operated from

the mains power supply (with a power cable)

and to battery operated electric tools (without a

power cable).

1. Workplace safety

 Keep your work area clean and well

illuminated. Untidy or unlit work areas can

result in accidents.

 Do not use this tool in a potentially

explosive environment containing

combustible liquids, gases or dust.

Electric tools generate sparks, which can in

turn ignite dust or vapors.

 Keep children and other persons away

from the electric tool while it is being

used.

Allowing yourself to get distracted can

cause you to lose control of the tool.

2. ELECTRICAL SAFETY

 The toolʼs connector plug must be able

to fit into the socket outlet. Do not

modify the plug in any way! Do not use

adapter plugs in conjunction with

electrically grounded tools.

Unmodified plugs and matching socket

outlets reduce the risk of an electric shock.

 Avoid touching grounded surfaces,

such as those of pipes/tubes, heaters,

cookers and refrigerators.

There is an increased risk of getting an

electric shock if you are electrically

grounded.

 Keep the tool away from rain and

moisture/wet conditions.

Penetration of water into an electric tool

increases the risk of an electric shock.

 Do not use the cable to carry the tool,

hang it up or pull the plug out of the

socket. Keep the cable away from

sources of heat, oil, sharp edges and

moving tool parts.

Damaged or tangled cable increases the

risk of an electric shock.

 If you intend to use an electric tool

outdoors, ensure that you only use

extension cable that is approved for

outdoor applications.

Using extension cable that is approved for

outdoor applications reduces the risk of an

electric shock.

 If operation of the electric tool in a

damp environment can not be avoided,

use a earth-leakage circuit-breaker.

The earth-leakage circuit-breaker reduces

the risk of an electric shock.

3. PERSONAL SAFETY

 Be alert, work conscientiously and

exercise appropriate caution when

using the electric tool. Do not use the

tool if you are tired or are under the

influence of drugs/medication or

alcohol.

One moment of carelessness or lack of

attention when using the electric tool can

cause serious bodily injury!

 Always wear personal protective

equipment (PPE), including safety

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 8

GB/IE/

CY

9

goggles.

Wearing personal protective equipment

such as a dust mask, non-slip footwear,

protective headgear and ear muffs

(depending upon the type of electric tool

and the particular application) reduces the

risk of sustaining injury.

 Make sure that the tool cannot start up

accidentally. Ensure that the electric

tool is switched off before you connect

the tool to the power supply and/or

insert the battery, or pick up or carry the

tool.

Physically touching the switch with your

finger when carrying the tool or connecting

the tool to the power supply switched on

can lead to accidents.

 Remove adjusting tools/wrench(es)

prior to switching on the power tool.

A tool or wrench that is positioned inside a

rotating power tool part can cause injury.

 Avoid abnormal working postures. Make

sure you stand squarely and keep your

balance at all times.

This way, you will be able to have better

control over the tool in unexpected

situations.

 Wear suitable clothes. Never wear loose

fitting clothes or jewelry. Keep hair,

clothes and gloves away from moving

parts.

Loose clothing, dangling jewelry and long

hair can be caught by moving parts.

 If dust extraction and dust collection

devices can be mounted, ensure that

these are connected and are properly

used.

The use of a dust extraction system can

reduce the danger posed by dust.

4. Using the treatment of electric tools

 Do not overload your tool. Only use

suitable electric tools to perform your

work.

Using the right electric tool allows you to

work better and safer within the toolʼs

quoted capacity

range.

 Do not use an electric tool whose switch

is defective.

An electric tool that no longer can be

switched on or off is dangerous and must

be repaired.

 Pull the plug out of the socket and/or

remove the battery before making any

adjustments to the tool, changing

accessories or put the tool down.

This precaution eliminates the possibility of

inadvertently starting the tool.

 When not in use, store electric tools out

of the reach of children. Do not allow

those persons to use this tool who are

unfamiliar with it or who have not read

these instructions.

Electric tools are dangerous when they are

used by inexperienced persons.

 Take good care of your tool. Check that

moving parts properly function and do

not jam, that parts are not broken off or

damaged in any way and that the tool

can be used to its full capacity. Have

damaged parts repaired prior to using

the tool.

The cause of many accidents can be traced

back to poorly maintained electric tools.

 Keep your blades sharp and clean.

Properly maintained blades with sharp

edges jam less frequently and are easier to

use.

 Make sure to use electric tools,

accessories, attachments, etc. in

accordance with these instructions.

Take the conditions in your work area

and the job in hand into account.

Using electric tools for applications other

than those intended can lead to dangerous

situations.

5. SERVICE

 Have your tool repaired only by

authorized specialists using original

replacement parts.

This will ensure that your tool remains safe

to use.

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 9

GB/IE/

CY

10

Additional Safety rules

 Check that your mains voltage is the same

as that marked on the rating plate.

 If you use a cable reel, run all the cable off

the reel. The minimum conductor cross

section used should be 1.5 mm

2

.

 If you use this electric hammer drill

outdoors you must connect it using a

suitable H07RN-F 3G 1.5 mm

2

extension

cable with a spray-water protected plug.

 Make sure of your footing, particularly when

working free-handed on ladders or

scaffolding.

 Use a detector to localize pipes and/or

cables in walls with concealed electric,

water or gas lines. Avoid any contact with

conducting electrical parts or lines.

 Wear ear-muffs to protect your hearing:

Risk of progressive loss of hearing!

 Wear goggles and use a breathing mask on

dusty jobs.

 Never use the machine near vapors or

combustible liquids.

 Always unplug the machine before cleaning

it or changing drill bits etc.

 Keep the power cable safe from damage.

Oil and acids can damage cables.

 Never overload the machine.

 Important!

Follow all safety regulations in your country

appli cable to the installation, use and

maintenance of the machine.

 Chisel bits and drill bits can be

inadvertently thrown out from the machine

and cause serious injury:

- Always check that the chisel bit or drill bit

is firmly locked in the chuck before you

start work.

- Check the chuck for wear or damage at

regular intervals.

 Do not start a hammering tool until it is

pressed against a workpiece (wall, ceiling,

etc.).

 Always unplug the hammer drill when you

have finished working and remove the

chisel bit or drill bit from the tool.

 Always unplug the machine before

changing chisel bits or drill bits etc.

 Protect eyes and assistants from small

flying parts and splinters. Wear a helmet!

Erect a screen wall!

 Work gloves protect you against skin

abrasions.

 Vibrations can be harmful to the hand-arm

system: Keep the impact time of vibrations

to a minimum.

 Always keep the power cable away from

where you want to drill.

 Keep the machine out of childrenʼs reach.

 Always hold the machine with two hands

when it is running and make sure of your

footing.

 Make sure that the switch on the machine

is set to the correct position for the work

you want to perform before you put the

machine into operation. If the switch is not

in the correct position you risk suffering

bodily injury when the machine starts to

run.

Save this instructions.

3. Layout (Fig. 1)

1. Dust guard

2. Locking sleeve

3. Additional handle

4. Lock for depth stop

5. Selector switch for drill/hammer drill/chisel

6. Handle

7. Clockwise/counter-clockwise switch

8. Locking button

9. Speed controller

10. ON/OFF switch

11. Operating status indicator

12. Indicator for carbon brush wear

13. Depth stop

14. Additional scroll chuck

15. Chuck key

16. Dust absorption device

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 10

GB/IE/

CY

11

4. Items supplied

Take all the parts out of the packaging.

Check that nothing is missing.

 BMH 1100 hammer drill

 Additional handle

 Depth stop

 Drill bits for stone (6, 8, 10 mm)

 Pointed chisel / flat chisel

 Additional scroll chuck

 Operating instructions

 Dust absorption device

 Chuck key

5. Proper use

The tool is designed for drilling with hammer

action in concrete, rock and brick, as well as

for chiseling work, always using the respective

correct drill or chisel bit.

The equipment is to be used only for its

prescribed purpose. Any other use is deemed

to be a case of misuse. The user / operator

and not the manufacturer will be liable for any

damage or injuries of any kind caused as a

result of this.

Please note that our equipment has not been

designed for use in commercial, trade or

industrial applications. Our warranty will be

voided if the machine is used in commercial,

trade or industrial businesses or for equivalent

purposes.

6. Technical data

Mains voltage: 230 V ~ 50 Hz

Power input: 1050 W

Idling speed: 0-1100 rpm

Blow rate: 0-5100 rpm

Drilling capacity in

concrete/stone (max.): 26 mm

Protection class: II / 쓑

Weight: 3.6 kg

Sound and vibration

Sound and vibration values were measured in

accordance with EN 60745.

L

pA

sound pressure level 91.8 dB(A)

K

pA

uncertainty 3 dB

L

WA

sound power level 102.8 dB(A)

K

WA

uncertainty 3 dB

The hammer drill is not designed for outdoors

use as specified I Article 3 of Directive

2000/14/EC_2005/88/EC.

Wear ear-muffs.

The impact of noise can cause damage to

hearing.

Total vibration values (vector sum of three

directions) determined in accordance with EN

60745.

Hammer drilling in concrete

Vibration emission value a

h

= 15.81 m/s

2

K uncertainty = 1.5 m/s

2

Chiseling

Vibration emission value a

h

= 15.668 m/s

2

K uncertainty = 1.5 m/s

2

 Important!

The vibration value changes according to the

area of application of the electric tool and may

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 11

exceed the specified value in exceptional

circumstances.

7. Before starting the equipment

 Important!

Before you connect the equipment to the

mains supply make sure that the data on the

rating plate are identical to the mains data.

Always pull the power plug before making

adjustments to the equipment.

Check the drilling point for concealed electrical

cables, gas and water pipes using a cable/pipe

detector.

7.1 Additional handle (Fig. 2 – Item 3)

For safety reasons you must only use the

hammer drill with the additional handle.

The additional handle (3) enables you to

achieve better stability whilst using the

equipment. Do not use the equipment without

the additional handle (3). The additional handle

(3) is secured to the equipment by a clamp.

Turning the additional handle (3) clockwise

tightens this clamp. Turning it anti-clockwise will

release the clamp.

 The supplied additional handle (3) must first

be fitted. To do this, turn the additional

handle (3) until the clamp is opened wide

enough for you to slide the additional handle

onto the equipment.

 After you have mounted the additional

handle (3), swivel it to the most comfortable

working position for yourself.

 Now turn the additional handle (3) in the

opposite direction again until the additional

handle (3) is secure.

 The additional handle (3) is suitable for both

left-handed and right-handed users.

7.2 Depth stop (Fig. 3 – Item 13)

The depth stop (13) is held in place by

clamping with the lock (4) on the additional

handle (3).

When mounting the depth stop (13), make sure

that the catch is on the bottom side.

 Press the lock (4) and keep it pressed it

while you adjust the depth stop (13).

 Set the depth stop (13) to the same level as

the drill bit.

 Pull the depth stop (13) back by the

required drilling depth.

 Let go of the lock (4).

 Now drill the hole until the depth stop (13)

touches the workpiece.

7.3. Tool insertion (Fig. 4)

 Clean the tool before insertion and apply a

thin coating of drill bit grease to the shaft of

the tool.

 Pull back and hold the locking sleeve (2).

 Turn and push the dust-free tool into the tool

mounting as far as it will go. The tool will

lock automatically, after the locking sleeve

is released.

 Check that it is properly secure by pulling

the tool.

7.4. Tool removal (Fig. 5)

Pull back and hold the locking sleeve (2) and

remove the tool.

7.5 Dust collection device (Fig. 8)

Slide the dust collection device (16) over the

drill bit before carrying out any hammer drilling

vertically above your head.

7.6. Fitting the additional scroll chuck

(Fig. 4)

 Clean the scroll chuck (14) before fitting it

and apply a thin coating of drill bit grease to

the scroll chuck shaft.

 Pull back and hold the locking sleeve (2).

 Turn and push the dust-free scroll chuck

(14) into the tool mounting as far as it will

go. The scroll chuck (14) will lock

automatically after the locking sleeve is

released.

 Check that it is secure by pulling the scroll

GB/IE/

CY

12

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 12

GB/IE/

CY

13

chuck (14).

7.7. Removing the additional scroll chuck

(Fig. 5)

Pull back and hold the locking sleeve (2) and

remove the scroll chuck.

7.8 Inserting the drill into the scroll chuck

(Figures 6-7)

 Important!

 Always pull the power plug before making

adjustments to the equipment.

 Release the depth stop (13) as described in

7.2 and push it towards the drill handle. This

provides free access to the scroll chuck

(14).

 Undo the scroll chuck (14) with the supplied

chuck key (15) by turning it anti-clockwise.

 To ensure that it is perfectly positioned the

drill bit or tool should be inserted as far as

possible into the scroll chuck (14). After

inserting the drill bit or tool, tighten the scroll

chuck (14) by turning the chuck key (15)

clockwise until the drill bit or tool is secure.

Check that the drill bit is secure in the scroll

chuck (14).

 Check at regular intervals that the drill bit or

tool is secure (pull the mains plug).

8. Starting up

 Important!

To prevent all danger, the machine must

only be held using the two handles (3/6).

Otherwise there may be a risk of suffering an

electric shock if you drill into cables.

8.1 Status indicator (Fig. 1/Item 11)

The status indicator (11) lights up when the

power plug is connected.

8.2 ON/OFF switch (Fig. 9/Item 10)

 First fit a suitable drill bit into the tool (see

7.3).

 Connect the mains plug to a suitable

socket.

 Position the drill in the position you wish to

drill.

To switch on:

Press the ON/OFF switch (10)

To switch off:

Release the ON/OFF switch (10)

Switching on continuous operation:

Secure the ON/OFF switch (10) with the

locking button (8).Important. It may only be

locked if the drill is set to rotate clockwise.

Switching off continuous operation:

Press the ON/OFF switch (10) briefly.

8.3 Adjusting the speed (Fig. 9/Item 10)

 You can infinitely vary the speed whilst

using the tool.

 Select the speed by applying a greater or

lesser pressure to the ON/OFF switch (10).

 Select the correct speed: The most suitable

speed depends on the workpiece, the type

of use and the drill bit used.

 Low pressure on the ON/OFF switch (10):

Lower speed

 Greater pressure on the ON/OFF switch

(10): Higher speed

Tip: Start drilling holes at low speed. Then

increase the speed in stages.

Benefits:

 The drill bit is easier to control when

starting the hole and will not slide away.

 You avoid drilling messy holes (for example

in tiles).

8.4 Preselecting the speed (Fig. 9/Item 9)

 The speed setting ring (9) enables you to

define the maximum speed. The ON/OFF

switch (10) can only be pressed to the

defined maximum speed setting.

 Set the speed using the setting ring (9) on

the ON/OFF switch (10).

 Do not attempt to make this setting whilst

the drill is in use.

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 13

8.5 Clockwise/Counter-clockwise switch

(Fig. 9/Item 7)

 Change switch position only when the

drill is at a standstill!

 Switch the direction of the hammer drill

using the clockwise/counter-clockwise

switch (7):

Direction Switch position

Clockwise Pushed in to the right

(forwards and drill)

Counter-clockwise Pushed in to the left

(reverse)

8.6 Drill / Hammer drill / Chisel selector

switch (Fig. 10)

 For drilling, press the button (E) on the

selector switch (5) and simultaneously turn

the selector switch (5) to position A.

 For hammer drilling, press the button (E) on

the selector switch (5) and simultaneously

turn the selector switch (5) to position B.

 For chiseling, press the button (E) on the

selector switch (5) and simultaneously turn

the selector switch (5) to position C. In

switch position C the chisel is not locked.

 For chiseling, press the button (E) on the

selector switch (5) and simultaneously turn

the selector switch (5) to position D. The

chisel is locked in position D.

Important.

You only require slight contact pressure for

hammer drilling. Excessive contact pressure

will place an unnecessary strain on the motor.

Check bitsl at regular intervals. Sharpen or

replace blunt bits.

9. Replacing the power cable

If the power cable for this equipment is

damaged, it must be replaced by the

manufacturer or its after-sales service or

similarly trained personnel to avoid danger.

10. Cleaning, maintenance and

ordering of spare parts

 Important.

Always pull out the mains power plug before

starting any cleaning work.

10.1 Cleaning

 Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

 We recommend that you clean the device

immediately each time you have finished

using it.

 Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could

attack the plastic parts of the equipment.

Ensure that no water can seep into the

device.

10.2 Carbon brushes

In case of excessive sparking or if the status

indicator for carbon brush wear (12) lights up,

have the carbon brushes checked by a qualified

electrician.

10.3 Maintenance

There are no parts inside the equipment which

require additional maintenance.

10.4 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

 Type of machine

 Article number of the machine

 Identification number of the machine

For our latest prices and information please go

to www.isc-gmbh.info

GB/IE/

CY

14

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 14

GB/IE/

CY

15

11. Disposal and recycling

The unit is supplied in packaging to prevent its

being damaged in transit. This packaging is

raw material and can therefore be reused or

can be returned to the raw material system.

The unit and its accessories are made of

various types of material, such as metal and

plastic. Defective components must be

disposed of as special waste. Ask your dealer

or your local council.

For EU countries only

Never place any electric tools in

your household refuse.

To comply with European Directive

2002/96/EC concerning old electric and

electronic equipment and its

implementation in national laws, old electric

tools have to be separated from other waste

and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the demand to return

electrical devices:

As an alternative to returning the electrical

device, the owner is obliged to cooperate in

ensuring that the device is properly recycled if

ownership is relinquished. This can also be

done by handing over the used

device to a returns center, which will dispose of

it in accordance with national commercial and

industrial waste management legislation. This

does not apply to the accessories and auxiliary

equipment without any electrical components

which are included with the used device.

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 15

GB/IE/

CY

16

k

erklärt folgende Konformität gemäß EU-Richtlinie

und Normen für Artikel

t

declares conformity with the EU Directive

and standards marked below for the article

p

déclare la conformité suivante selon la

directive CE et les normes concernant lʼarticle



verklaart de volgende conformiteit in overeen-

stemming met de EU-richtlijn en normen voor

het artikel

m

declara la siguiente conformidad a tenor de la

directiva y normas de la UE para el artículo

O

declara a seguinte conformidade de acordo

com a directiva CE e normas para o artigo

U

förklarar följande överensstämmelse enl. EU-

direktiv och standarder för artikeln

q

ilmoittaa seuraavaa Euroopan unionin direkti-

ivien ja normien mukaista yhdenmukaisuutta

tuotteelle



erklærer herved følgende samsvar med EU-

direktiv og standarder for artikkel

T

заявляет о соответствии товара

следующим директивам и нормам EC

B

izjavljuje sljedeću uskladjenost s odredbama i

normama EU za artikl.

Q

declarå urmåtoarea conformitate cu linia direc-

toare CE μi normele valabile pentru articolul.

Z

ürün ile ilgili olarak AB Yönetmelikleri ve

mas∂n∂ sunar.

z

‰ËÏÒÓÂÈ ÙËÓ ·ÎﬁÏÔ˘ıË Û˘ÌÊˆÓ›· Û‡ÌÊˆÓ· ÌÂ

ÙËÓ √‰ËÁ›· ∂∂ Î·È Ù· ÚﬁÙ˘Ô ÁÈ· ÙÔ ÚÔ˚ﬁÓ

C dichiara la seguente conformità secondo la

direttiva UE e le norme per lʼarticolo

l

attesterer følgende overensstemmelse i

henhold til EU-direktiv og standarder for produkt

j

prohlašuje následující shodu podle směrnice

EU a norem pro výrobek.

A

a következő konformitást jelenti ki a termékek-

re vonatkozó EU-irányvonalak és normák szerint

X

pojasnjuje sledečo skladnost po smernici EU

in normah za artikel.

ཚ

deklaruje zgodność wymienionego poniżej

artykułu z następującymi normami na

podstawie dyrektywy WE.

W

vydáva nasledujúce prehlásenie o zhode podľa

smernice EÚ a noriem pre výrobok.

e

деклаpиpа следното съответствие съгласно

диpективите и ноpмите на ЕС за пpодукта.

1

заявляє про відповідність згідно з Директивою

ЄС та стандартами, чинними для даного товару

.

deklareerib vastavuse järgnevatele EL direktiivi

dele ja normidele

G

deklaruoja atitikti pagal ES direktyvas ir normas

straipsniui

4

izjavljuje sledeçi konformitet u skladu s odred

bom EZ i normama za artikl

H

Atbilstības sertifikāts apliecina zemāk minēto preču

atbilstību ES direktīvām un standartiem

E

Samræmisyfirl‡sing sta›festir eftirfarandi samræmi

samkvæmt reglum Evfrópubandalagsins og stö›lum

fyrir vörur

Konformitätserklärung

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Bohrhammer BMH 1100

Art.-Nr.: 42.583.98 I.-Nr.: 01018 Archivierung: 4258395-42-4155050-08

Subject to change without notice

EN 60745-1; EN 60745-2-6; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 16.07.2008

Mayr

Product-Management

Weichselgartner

General-Manager

98/37/EC

2006/95/EC

97/23/EC

2004/108/EC

90/396/EEC

89/686/EEC

87/404/EEC

R&TTED 1999/5/EC

2000/14/EC_2005/88/EC:

95/54/EC:

97/68/EC:

X

12. Declaration of conformity

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 16

GB/IE/

CY

17

13. GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely

event that your device develops a fault, please contact our service department at the address shown on this

guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under

the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.

We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the

rectification of these defects or replacement of the device. Please note that our devices have not been

designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated

if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The

following are also excluded from our guarantee: compensation for transport damage, damage caused by

failure to comply with the installation/assembly instructions or damage caused by unprofessional

installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or

current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools

or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies

into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by

the device being dropped) and normal wear resulting from proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee

claims should be submitted before the end of the guarantee period within two weeks of the defect being

noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee

period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts fitted will not result in an extension of the guarantee period, and no new

guarantee will become active for the work performed or parts fitted. This also applies when an on-site

service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address

shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of

purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if

you could describe the nature of the problem in as much detail as possible. If the defect is covered by our

guarantee then your device will either be repaired immediately and returned to you, or we will send you a

new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the

scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send

the device to our service address.

Einhell UK Ltd

Morpeth Wharf ·Twelve Quays

Birkenhead, Wirral

CH41 1NG

Tel. 0151 6491500 · Fax 0151 6491501

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 17

FI

18

Sisällysluettelo Sivu

1. Johdanto ................................................................................20

2. Turvallisuusmääräykset ..........................................................20-22

3. Laitekuvaus.............................................................................22

4. Toimituksen laajuus ................................................................23

5. Määräysten mukainen käyttö ..................................................23

6. Tekniset tiedot.........................................................................23

7. Ennen käyttöönottoa ...............................................................24-25

8. Käyttöönotto............................................................................25-26

9. Verkkojohdon vaihtaminen......................................................26

10. Puhdistus, huolto ja varaosatilaus...........................................26-27

11. Käytöstäpoisto ja uusiokäyttö .................................................27

12. Standardinmukaisuustodistus.................................................28

13. Takuutodistus .........................................................................29

Tuotteiden dokumentaatioiden ja muiden

mukaanliitettyjen asiakirjojen vain osittainenkin

kopiointi tai muunlainen monistaminen on

sallittu ainoastaan ISC GmbH nimenomaisella

luvalla.

Oikeus teknisiin muutoksiin pidätetään

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 18

FI

19

Varoitus – Tapaturmavaaran vähentämiseksi lue käyttöohje

Käytä kuulosuojuksia.

Melun vaikutus saattaa aiheuttaa kuulon heikkenemistä.



Käytä pölynaamaria.

Puun ja muiden materiaalien työstössä saattaa syntyä terveydelle vaarallista pölyä.

Asbestipitoista materiaalia ei saa työstää!



Käytä suojalaseja.

Työssä syntyvät kipinät tai laitteesta sinkoutuvat sirpaleet, lastut ja pölyt saattavat

aiheuttaa näkökyvyn menetyksen.



Vaihdepyörästön vahingoittumisen välttämiseksi saa porauksen /

iskuporauksen vaihtokytkimen kytkeä vain koneen seistessä

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 19

1. Johdanto

 Huomio!

Sähkölaitteita käytettäessä tulee noudattaa

tiettyjä turvallisuusvarotoimia tapaturmien ja

vaurioiden välttämiseksi. Lue sen vuoksi tämä

käyttöohje huolellisesti läpi. Säilytä se hyvin,

jotta siinä olevat tiedot ovat myöhemminkin

milloin vain käytettävissäsi. Jos luovutat

laitteen muille henkilöille, anna heille myös

tämä käyttöohje laitteen mukana.

Emme ota mitään vastuuta tapaturmista tai

vaurioista, jotka ovat aiheutuneet tämän

käyttöohjeen tai turvallisuusohjeiden

noudattamisen laiminlyönnistä.

2. Turvallisuusmääräykset

 VAROITUS!

Lue kaikki turvallisuusmääräykset ja

ohjeet.

Jos turvallisuusmääräyksiä tai muita ohjeita ei

noudateta, saattaa tästä aiheutua sähköiskuja,

tulipaloja ja/tai vaikeita vammoja.

Säilytä kaikki turvallisuusmääräykset ja

ohjeet myöhempää tarvetta varten.

Turvallisuusmääräyksissä käytetyllä käsitteellä

„sähkötyökalu“ tarkoitetaan

verkkovirtakäyttöisiä sähkötyökaluja (varustettu

verkkojohdolla) sekä akkukäyttöisiä

sähkötyökaluja (ilman verkkojohtoa).

1. Työpaikan turvallisuus

 Pidä työalueesi siistinä ja hyvin

valaistuna. Työalueella vallitsevasta

epäjärjestyksestä tai huonosta

valaistuksesta voi aiheutua tapaturmia.

 Älä käytä tätä laitetta äjähdysalttiissa

ympäristössä, jossa on tulenarkoja

nesteitä, kaasuja tai pölyjä.

Sähkötyökalut kehittävät kipinöitä, jotka

saattavat sytyttää pölyn tai höyryt.

 Pidä lapset ja muut henkilöt poissa

työalueelta sähkötyökalun käytön

aikana.

Saatat menettää laitteen hallinnan

häiriötekijöiden vuoksi.

2. SÄHKÖTURVALLISUUS

 Laitteen liitäntäpistokkeen tulee sopia

pistorasiaan. Pistoketta ei saa muuttaa

millään tavalla. Älä käytä

sovitinpistokkeita suojamaadoitetuissa

laitteissa.

Muuttamattomat pistokkeet ja sopivat

pistorasiat vähentävät sähköiskun vaaraa.

 Vältä koskemasta vartalollasi

maadoitettuihin osiin, esim. putkiin,

lämmittimiin, liesiin ja jääkaappeihin.

Sähköiskun vaara lisääntyy, jos vartalosi on

maadoitettu.

 Suojaa laitetta kosteudelta tai sateelta.

Veden tunkeutuminen sähkölaitteen sisään

lisää sähköiskun vaaraa.

 Älä käytä johtoa väärin: älä kanna

sähkötyökalua verkkojohdosta, ripusta

laitetta siitä riippumaan tai käytä sitä

pistokkeen vetämiseen pistorasiasta.

Suojaa johto kuumuudelta, öljyltä,

teräviltä reunoilta tai liikkuvilta laitteen

osilta.

Vahingoittuneet tai solmuun kiertyneet

johdot lisäävät sähköiskun vaaraa.

 Kun käytät sähkötyökalua ulkona, käytä

vain sellaisia jatkojohtoja, jotka on

hyväksytty ulkokäyttöä varten.

Ulkokäyttöön hyväksytyn jatkojohdon

käyttäminen vähentää sähköiskun vaaraa.

 Jos sähkötyökalun käyttö kosteassa

ympäristössä on välttämätöntä, käytä

vuotovirtasuojakatkaisinta.

Vuotovirtasuojakatkaisimen käyttö vähentää

sähköiskun vaaraa.

3. IHMISTEN TURVALLISUUS

 Ole tarkkaavainen työskennellessäsi ja

käytä järkeäsi, kun käsittelet

sähkötyökaluja. Älä käytä laitetta, jos

olet väsynyt tai huumeiden, alkoholin tai

lääkkeitten vaikutuksen alainen.

Hetkenkin hajamielisyys sähkötyökaluja

käytettessä saattaa johtaa vakaviin

vammoihin.

 Käytä henkilökohtaisia suojavarusteita

sekä aina suojalaseja.

Henkilökohtaisten suojavarusteiden, kuten

pölynaamarin, luistamattomien

turvajalkineiden, kypärän tai kuulosuojusten

FI

20

Anleitung_BMH_1100_4258398:_ 21.11.2008 7:40 Uhr Seite 20

Sivu latautuu ...

Parkside BMH 1100 Käyttö ohjeet

Parkside BMH 1100 Käyttö ohjeet

muilla kielillä

Liittyvät paperit

Muut asiakirjat