Yamaha GX-500 Ohjekirja

Kategoria
CD players
Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

G
U C A
3
DISC CD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
MINI COMPONENT SYSTEM GX–500
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DOLBY B NR
PTY SELECT
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC
1
DISC
2
DISC
3
DISC CHANGE OPEN
/
CLOSE
YMERSION
B.BOOST
MUSIC
INPUTINPUT
DIRECTION
MINI COMPONENT SYSTEM GX-500
PUSH OPEN
OWNER’S MANUAL
MODE D’EMPLOI
OWNER’S MANUAL
MODE D’EMPLOI
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause
the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation. For
example, the unit should not be situated on a bed, sofa,
rug, or similar surface, that may block the ventilation
openings; or placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9 Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating instruc-
tions. All other servicing should be referred to qualified
service personnel.
17 Power Lines – An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
IMPORTANT
Please record the serial number of this system
in the space below.
Model:
Serial No.:
The serial number is located on the rear of the
main unit.
Retain this Owner’s Manual in a safe place for
future reference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the
grounding electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT :
When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to
eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
1
11
2
22
Unpacking After unpacking, check that the following parts are contained.
Déballage Après le déballage, vérifier que les pièces suivantes sont incluses.
Main unit
Appareil principal
Remote control
Télécommande
Batteries (size AA, UM/SUM-3, R6, HP-7)
Piles (format AA, UM/SUM-3, R6, HP-7)
Speakers
Enceintes
Speaker cords
Câbles d’enceintes
AM loop antenna
Antenne-cadre AM
Indoor FM antenna
Antenne intérieure FM
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+I0
E
MODE REPEAT
RANDOM
TUNER
DISC SKIP
REC/PAUSE
DIRECTION
YMERSION
BASS BOOST
MUSIC
POWER SLEEP
INPUT
VOLUME
AB
TAPE
TUNER
CD
/
I
DISC
1
DISC
2
DISC
3
3
DISC CD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
PUSH OPEN
MINI COMPONENT SYSTEM GX–500
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DOLBY B NR
DIRECTION
YMERSION B.BOOST
MUSIC
INPUTINPUT
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
3
33
1 cm 1 cm
20 cm20 cm
20 cm
20 cm
20 cm
20 cm 20 cm
20 cm
Setting this system Installation de ce système
English
Set this system allowing enough spaces around and behind the main unit to assure good ventilation. Be sure not to place
another unit or any object on top of the main unit to prevent the ventilation holes from being obstructed. Otherwise, it may
cause fire or damage to the main unit.
Note
When placing the speakers apart from the main unit, be sure to allow a space of at least 20 cm above, behind and on
both sides of the main unit. If the main unit is put in a rack, the front of it must be fully opened.
* The values must be applied to China and Singapore models only.
Français
Installer ce système en laissant assez d’espace autour et derrière l’appareil principal pour assurer une bonne
ventilation. Veiller à ne pas empiler un autre appareil ou un autre objet sur l’appareil principal afin de ne pas boucher
les orifices de ventilation. Sinon, on risquerait de provoquer un incendie ou d’endommager l’appareil principal.
Remarque
Lorsqu’on place les enceintes à une certaine distance de l’appareil principal, veiller à laisser un espace d’au moins 20
cm au-dessus, derrière et sur les deux côtés de l’appareil principal. Si l’on place l’appareil principal dans un meuble,
veiller à ce que le côté avant du meuble soit grand ouvert.
*
Les valeurs ne doivent être appliquées qu’aux modèles pour la Chine et Singapour.
4
44
DISC
1
DISC
2
DISC
3
3
DISC CD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DOLBY B NR
DIRECTION
YMERSION
B.BOOST
MUSIC
INPUTINPUT
PHONES
MIN
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
TREBLEBASS
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSEDOLBY NR
HOUR
RANDOM
REPEAT TIME
DISPLAYMODE
]
\ZX [YW
`
K
J
I
H
G,
U
T
F, S
E
D
C
B, R
A, Q
0, P
L
ONM
2
3
4
5
6
7
8
9
V
1
Front panel Panneau avant
5
55
1 Display
Panneau d’affichage
2 Remote control sensor
Capteur de télécommande
3 TIMER
4 STANDBY [P. 9]
5 B. BOOST [P. 28]
6 YMERSION [P. 28]
7 PHONES [P. 28]
L Disc tray
Plateau de disque
[P. 9]
M DISC (1, 2, 3) [P. 10]
N DISC CHANGE [P. 10]
Amplifier/tuner Amplificateur/tuner
8 BASS/TREBLE [P. 28]
9 Front cover
Couvercle avant
0 / [P. 15, 16]
A A/B/C/D/E [P. 16]
B PRESET/TUNING/BAND
[P. 15]
C VOLUME [P. 27]
D MUSIC [P. 27]
E INPUT( / ) [P. 9, 15, 19, 25]
F HOUR [P. 7, 29]
G MIN [P. 7, 29]
H DISPLAY [P. 7, 29]
I MEMORY [P. 16, 17]
TIME ADJ [P. 7]
J STANDBY/ON [P. 9]
K AUTO/MANUAL [P. 15]
TIMER [P. 29]
O OPEN/CLOSE [P. 9]
P ( )/ ( ) [P. 10]
Q / [P. 9]
R [P. 9]
S RANDOM [P. 12]
T TIME [P. 13]
U REPEAT [P. 12]
V Tray
Plateau
[P. 19]
W MODE [P. 19]
X [P. 19]
Y DIRECTION [P. 19]
Z ( )/ ( ) [P. 20]
[ [P. 19]
\ [P. 19]
] REC/PAUSE [P. 21]
` DOLBY NR [P. 18, 21]
CD player Lecteur de disque compact
Tape deck Platine cassette
TUNER TAPE CD AUX/MD
6
66
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+I0
E
MODE REPEAT
RANDOM
TUNER
DISC SKIP
REC/PAUSE
DIRECTION
YMERSION
BASS BOOST
MUSIC
POWER SLEEP
INPUT
VOLUME
AB
TAPE
TUNER
CD
/
I
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
E
MODE REPEAT
RANDOM
TUNER
DISC SKIP
AB
TUNER
CD
REC/PAUSE
DIRECTION
YMERSION
BASS BOOST
MUSIC
POWER SLEEP
INPUT
VOLUME
TAPE
/I
+I0
2
3
5
4
6
B
A
9
8
7
0
C
D
F
E
G
H I J K L
M
N
S
RQP
O
1
Remote control Telecommande
7
77
1 Transmission window
Fenêtre de transmission
[p. 4]
2 Numeric buttons
Touches numériques
[p. 16]
3 A, B, C, D, E [p. 16]
4 YMERSION [p. 28]
5 POWER [p. 9]
C Numeric buttons
Touches numériques
[p. 10]
D TIME [p. 13]
E PROG [p. 11]
F MODE [p. 9]
6 SLEEP [p. 30]
7 PRESET ( / ) [p. 16]
8 TUNER [p. 15]
9 MUSIC [p. 27]
0 BASS BOOST [p. 28]
A VOLUME (+/–) [p. 27]
B INPUT ( / ) [p. 9, 15, 19, 25]
G DISC SKIP
[p. 10]
H REPEAT [p. 12]
I ( )/ ( ) [p. 10]
J RANDOM [p. 12]
K [p. 9]
L [p. 9]
M EDIT [p. 23]
N R. TIME [p. 23]
O REC/PAUSE [p. 21]
P / [p. 20]
Q [p. 19]
R [p. 19]
Amplifier/tuner Amplificateur/tuner
CD player Lecteur de disque compact
Tape deck Platine cassette
S DIRECTION [p. 19]
TUNER TAPE CD AUX/MD
Contents
English
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment.
For the best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
Page
SAFETY INSTRUCTIONS
.............................Inside of the Front Cover
Precautions.................................................
1
Features ......................................................
3
Preparations and connections..................
4
Installing batteries in the remote control .................. 4
Remote control operation range ..............................4
Connections .............................................................5
Setting the clock....................................................... 7
Adjusting brightness of the display ..........................7
Compact disc player operation.................
8
Basic play................................................................. 9
To change the disc play mode .................................9
To select another disc ............................................ 10
To select the desired track directly .........................10
To play the desired track (Skip).............................. 10
To advance or reverse play rapidly (Search).......... 10
To exchange a disc (or discs) while playing
(PLAYXCHANGE) ..................................................10
Program play.......................................................... 11
Random play ..........................................................12
Repeat play ............................................................12
Switching the time display...................................... 13
Tuning operation ......................................
14
Automatic tuning .................................................... 15
Manual tuning ........................................................15
Manual preset tuning .............................................16
Automatic preset tuning ......................................... 17
Page
Playing back a tape ..................................
18
General information ...............................................18
Basic operation ...................................................... 19
Winding the tape ....................................................20
Searching for the beginning
of the desired selection ..........................................20
Recording .................................................
21
Basic recording ...................................................... 21
Recording from CDs utilizing the EDIT function..... 23
Operating the external unit
connected with this system ....................
26
Various sound control .............................
27
Using the built-in timer ............................
29
Timer play .............................................................. 29
Timer recording...................................................... 30
Sleep timer operation............................................. 30
Appendix...................................................
31
Troubleshooting .....................................................31
Specifications......................................................... 33
For basic source play, the following illustrations on top of
pages will help you to look for the section you need.
......CD play ......Tuning
......Tape playback/recording
E-1
English
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Choose the installation location of this system carefully.
Avoid placing it in direct sunlight or close to a source of
heat. Also avoid locations subject to vibration and
excessive dust, heat, cold or moisture. Keep it away from
sources of hum such as transformers and electric motors.
Do not operate this system upside-down. It may overheat,
possibly causing damage.
Never open the cabinet. If something drops into the set,
contact your dealer.
The openings on the main unit cover assure proper
ventilation of the main unit. If these openings are
obstructed, the temperature inside the main unit will rise
rapidly. Therefore, avoid placing objects against these
openings, and install the main unit in a well-ventilated area
to prevent fire and damage.
Always set the VOLUME control to minimum before
starting an audio source play: increase the volume
gradually to an appropriate level after play has started.
When not planning to use this system for long periods of
time (ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
Grounding or polarization – Precautions should be taken so
that the grounding or polarization of this system is not
defeated.
Do not use force on switches, controls or connection wires.
When moving the main unit, first disconnect the power plug
and the wires connected to other equipment. Never pull the
wire itself.
If an external appliance (TV, radio, etc.) interferes with this
system operation, move the main unit away from such an
appliance.
Do not attempt to clean this system with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
Be sure to read the “Troubleshooting” section regarding
common operating errors before concluding that this
system is faulty.
To prevent lightning damage, disconnect the AC power
plug and the antenna cable when there is an electrical
storm.
Do not plug the AC power plug to the wall socket before
you finish all connections.
Never allow metallic items (e.g. screwdrivers, tools, etc.) to
come near the tape deck’s record/playback head assembly.
Doing so may not only scratch or damage the head’s
mirror-smooth finish, it may change the magnetic
characteristics of the heads, causing a deterioration in
reproduction performance quality.
Although the tape deck’s record/playback heads are high
quality heads with outstanding reproduction characteristics,
they can become dirty through the use of old tapes or from
dust accumulation over time. This can have a serious effect
on reproduction quality. Clean the heads regularly with one
of the commonly available head cleaners or with cleaning
solutions.
The voltage to be used must be the same as that specified
on this system. Using this system with a higher voltage
than specified is dangerous and may result in a fire or other
types of accidents causing damage. YAMAHA will not be
held responsible for any damage resulting from use of this
system with a voltage other than specified.
The sound level at a given volume setting depends on
speaker location and other factors. Care should be taken to
avoid exposure to sudden high levels of sound, which may
occur when turning on this system with the volume control
setting at high, and to continuous high levels of sound.
Sudden temperature changes and storage or operation in
an extremely humid environment may cause condensation
inside the cabinet. Condensation can cause this system to
malfunction.
To eliminate condensation:
CD pickup
Leave the power on with no disc loaded until normal
play becomes possible (about 1 hour).
Tape head
Leave the power on with no tape loaded until normal
playback becomes possible (about 1 hour).
Note
If condensation forms on the tape head, dirt or dust
may accumulate during use.
Remote control
Wipe off condensation on the transmission window with
a soft cloth before operating this system.
To prevent a malfunction of this system:
Do not use any non standard shaped disc (heart etc.)
available on the market, because it may damage this
system.
Do not use a disc with tape, seals, or paste on it,
because damage to this system may result.
Precautions: Read this before operating your system
E-2
Precautions: Read this before operating your system
WARNING
To reduce the risk of fire or electric shock, do not expose this
system to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
As the laser beam used in this unit is harmful to the eyes, do
not attempt to disassemble the cabinet. Refer servicing to
qualified personnel only.
This system is classified as a
CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT label is located on
the rear exterior.
CLASS 1 LASER PRODUCT
Laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
CAUTION FOR CARRYING THE MAIN UNIT
Be sure not to carry or tip the main unit with discs
remaining in it.
CAUTION FOR MOVING THE MAIN UNIT
Before moving the main unit, first remove all discs from the
disc tray and close the tray by pressing the OPEN/CLOSE
button. After you confirm that “NO DISC” lights up on the
display, turn this system into the standby mode by pressing
the STANDBY/ON switch, and then disconnect the power
plug from the AC outlet.
This system is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
this system itself is turned off. This state is called the
standby mode.
In this state, this system is designed to consume a certain
level of power.
Note
Please check the copyright laws in your country to record
from records, compact discs, radio, etc. Recording of
copyright material may infringe copyright laws.
For Canadian Customers
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES–003.
E-3
English
Features
General
High Power Output
80W + 80W (6) RMS, 0.9% THD, 1 kHz
Multi-use Timer/Sleep Timer
SUBWOOFER Output for Low Frequency
Expansion
Remote Control Capability
YMERSION
BASS BOOST
5-Band Spectrum Analyzer
3 Preset Graphic Equalizer Modes
(ROCK, POPS and JAZZ)
Compact Disc Player
3-Disc Carousel Type CD Changer
PLAYXCHANGE
Disc changing while playing
20-Track Random Access Programming
Repeat Play for Single Track/Entire Disc/
All Discs
Random Sequence Play
Tape Deck
Automatic Synchronized Recording with
CD
EDIT Function Useful for Recording
CD(s)
Automatic Reverse
Dolby B Type Noise Reduction System
Tuner
40 Station Preset Tuning
Automatic Preset Tuning
E-4
1. Turn the remote control over and remove the battery
compartment cover by pulling it up while pressing the edge
of the cover in the direction of the mark.
2. Insert the batteries (AA, R6, UM-3 type) according to the
polarity markings on the inside of the battery compartment.
3. Attach the battery compartment cover.
Notes
Remove the batteries if the remote control is not used for an
extended period of time.
If batteries leak, dispose of them immediately. Avoid
touching the leaked material and contact with clothing, etc.
Clean the battery compartment thoroughly before installing
new batteries.
Be sure to use the same type of batteries together.
Do not use a new battery and an old battery together.
Preparations and connections
Installing batteries in the remote control
Notes
The area between the remote control and the main unit must
be clear of large obstacles.
Do not expose the remote control sensor to strong lighting,
in particular, an inverter type fluorescent lamp. Otherwise,
the remote control may not work properly. If necessary,
position the main unit away from direct lighting.
Battery replacement
If you find that the remote control must be used closer to the
main unit, the batteries are weak. Replace both batteries with
new ones.
Remote control operation range
2
1
3
SET MD
REC/PAUSE
TAPE
DISC
1
DISC
2
DISC
3
3
DISC VCD CHANGER
DOWN UP
VOLUME
PUSH OPEN
MINI COMPONENT SYSTEM GX–700
MINIDISC RECORDER
MD
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
MODE
PTY SEEK
START
30°
30°
0,2 m – 6 m
E-5
English
Preparations and connections
Never plug the AC supply lead of this system into the AC outlet until all connections are completed.
Connections
Caution
Do not let the bare speaker wires touch each other as this could damage the amplifier and/or speakers.
When connecting a subwoofer (separate purchase)
You may wish to add a subwoofer to reinforce the bass frequencies.
When connecting a subwoofer to this system, connect the SUBWOOFER OUT terminal of this system to the INPUT terminal of the
subwoofer.
* Ordinary subwoofers, including the Yamaha Active Servo Processing Subwoofer System, are designed so that the amplifier and
subwoofer are in the same unit.
* The SUBWOOFER OUT terminal outputs low frequencies from both left and right channels.
(The cut-off frequency of this terminal is 200 Hz.)
m Connecting speakers
Connect the speakers to the corresponding speaker terminals on the rear of the main unit respectively by using the speaker cords.
Make sure that the polarity of the speaker cords is correct, that is the + and – markings are observed. If these cords are reversed,
the sound will be unnatural and lack bass.
On the main unit
Red: positive (+)
Black: negative (–)
1 Press up the tab.
2 Insert the bare wire.
[Remove approx. 5mm (1/4”)
insulation from the speaker
wires.]
3 Press down the tab and
secure the wire.
1
2
3
On the speakers
Red: positive (+)
Black: negative (–) 1 Press the tab
2 Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
3 Release the tab and
secure the wire.
RL
ANTENNA
75 UNBAL.
FM GND AM
DIGITAL OUT
OPTICAL
OUT
RL
OUT
IN
SEE OWNER’S MANUAL
FOR CONNECTION.
FRONT
SPEAKERS
6 MIN./SPEAKER
MAINS
SUBWOOFER
AUX/MD
L
R
RL
SEE OW
FOR CON
FRONT
SPEAKERS
6 MIN
OUT
SUBWOOFER
INPUT
Subwoofer system
(Separate purchase)
Speakers
To AC outlet
(U.S.A. model)
1
2
3
E-6
Preparations and connections
m Connecting an external component
This system can be connected with an external audio
component. Make connections between this system and the
component using RCA pin plug connector cables correctly,
that is to say L (left) to L and R (right) to R. Also, refer to the
owner’s manual for the component to be connected to this
system.
* A digital-to-digital recording is possible from a CD played on
the built-in CD player to an MD (or tape) on an external MD
recorder (or DAT) by connecting the DIGITAL OUT
(OPTICAL) terminal on the rear of the main unit to the MD
recorder (or DAT).
m Antenna connection
(1) Supplied FM antenna
Connect the FM antenna wire to the corresponding terminal
and direct the FM antenna wire to the direction where the
strongest signal can be received.
(2) Supplied AM loop antenna
Connect the AM loop antenna wires to the corresponding
terminals. Position the AM loop antenna for optimum
reception.
Notes
When static is still heard even after adjusting the position of
the AM loop antenna, try reversing the wire connections
(from the right terminal to the left one, and vice versa).
The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
Using an external antenna
Use an external FM antenna instead of an indoor FM
antenna if you need better reception. Consult your dealer.
Use an external AM antenna if you need better reception.
Consult your dealer.
RL
ANTENNA
75 UNBAL.
FM GND AM
DIGITAL OUT
OPTICAL
OUT
RL
OUT
IN
SEE OWN
E
FOR CON
N
FRONT
SPEAKERS
6 MIN.
/
SUBWOOFER
AUX/MD
(1)
(2)
ANTENNA
75 UNBAL.
FM GND AM
ANTENNA
75 UNBAL.
FM GND AM
DIGITAL OUT
OPTICAL
ANTENNA
75 UNBAL.
FM GND AM
DIGITAL IN
IN
OUT
(U.S.A. model)
(U.S.A. model)
MD recorder, etc.
English
E-7
DISC
1
DISC
2
DISC
3
DOWN UP
VOLUME
STANDBY/ON
YMERSION
B.BOOST
MUSIC
INPUTINPUT
MIN
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSEDOLBY NR
HOUR
RANDOM
REPEAT TIME
DISPLAYMODE
DISC
1
DISC
2
DISC
3
3
DISC CD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DOLBY B NR
DIRECTION
YMERSION
B.BOOST
MUSIC
INPUTINPUT
PHONES
MIN
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
TREBLEBASS
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSEDOLBY NR
HOUR
RANDOM
REPEAT TIME
DISPLAYMODE
1
2
3
RANDOM
REPEAT
HOUR
MIN
RANDOM
REPEAT
HOUR
MIN
DISPLAY
MEMORY
TIME ADJ
MEMORY
TIME ADJ
1 While the power is on, press DISPLAY to display the time.
2 While holding TIME ADJ pressed, press HOUR and set the
hour.
* Press HOUR once to advance the time by 1hour. Press
and hold to advance continuously.
3 While holding TIME ADJ pressed, press MIN and set the
minute.
* Press MIN once to advance the time by 1
minute. Press and hold to advance continuously.
* The hour setting will not advance even if minute is
advanced from “59” to “00”.
Australia model use a 24-hour display. U.S.A. and Canada
models use a 12-hour display. For China and General
models, either the 24-hour display or the 12-hour display
[shown by “AM (PM) 12:00”] is selected depending on the
setting of the FREQUENCY STEP switch on the rear
panel, so you cannot select the desired type freely.
Note
In the event of a power failure or when the AC supply lead is
disconnected, the time display will go out, however, the clock
will function for about 5 minutes without any power supply.
Otherwise, the time display will flash on and off to indicate that
the time must be reset.
If desired, you can adjust the brightness of the display.
Press and hold DISPLAY for more than 2 seconds so that
“DIMMER ±0” appears on the display.
While holding DISPLAY pressed, turn VOLUME clockwise to
increase or counterclockwise to decrease brightness.
Control range: ±0 to –6 (Preset value: ±0)
Setting the clock
VOLUME
DISPLAY
Adjusting brightness of the display
Changes.
Changes.
Preparations and connections
E-8
Compact disc player operation
100 350 1K 3.5K 10K
MUSIC
PROG
S F REP
VOLUME
OVER 15
1234
78910
13 14 15
5
11
6
12
TOTAL REM
TRACK
RANDOM
CD
PROGRAM
312
8
0
547
9
6
1 TRACK (track number)
2 Time display
3 Disc indicator
The disc of the number located on the top of this indicator is
now being selected.
4 CD (input source indicator)
5 (play)
6 RANDOM
Display information
7
Music calendar
Track numbers on the currently selected disc will be
illuminated (up to the number 15).
8 OVER 15
This indicator will be illuminated when the currently selected
disc has more than 15 tracks.
9 PROG (program)
0 (S, F) REP [(single, full) repeat]
Each indicator mentioned with a number on pages 9 –13 corresponds to the indicator with the same number on this page.
E-9
English
DISC
1
DISC
2
DISC
3
3
DISC CD CHANGER
STANDBY TIMER
DOWN UP
VOLUME
STANDBY/ON
AUTO REVERSE CASSETTE DECK
DOLBY B NR
DIRECTION
YMERSION
B.BOOST
MUSIC
INPUTINPUT
PHONES
MIN
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
TREBLEBASS
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSEDOLBY NR
HOUR
RANDOM
REPEAT TIME
DISPLAYMODE
Basic play
1
Turn on the power.
2 Select the CD player by pressing INPUT or until
“CD” (
2, 4) appears on the display.
3 Press OPEN/CLOSE to open the disc tray.
4 Place discs on the table, label side upward.
* Up to three discs can be loaded on the table.
To load the third disc, rotate the disc table by pressing
DISC CHANGE on the front panel.
* 8 cm (3”) discs can be played without an adaptor.
* The disc placed on the left side is played first.
5 Press OPEN/CLOSE to close the disc tray.
* The total number of tracks (
1) and the total playing
time of the disc being selected (
2) will be displayed for
several seconds.
* If the compact disc contains more than 15 tracks, the
“OVER 15” indicator (
8) will light up.
* If the disc tray is closed by pushing the front edge of the
tray, play will begin automatically.
6 Press / to begin play.
To pause
11 Press / .
* The “
” indicator (5) will flash.
22 Press / to resume play from the same point.
To stop play
Press .
To finish using this system
Turn this system into the standby mode by pressing
STANDBY/ON. (The STANDBY indicator will light up and the
display will go out.)
Direct operation
DISC (1, 2 or 3) and OPEN/CLOSE on the front panel and
on the remote control will work if they are pressed when
this system is in the standby mode or another input source is
selected.
3, 5
Compact disc player operation
Lights up only when the all disc play
mode is selected.
To change the disc play mode
If necessary, change the disc play mode by pressing MODE on
the remote control.
Single disc play mode: Only the designated disc is
played.
All disc play mode: All discs on the disc tray are
played sequentially.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+
I0
E
MODE REPEAT
RANDOM
TUNER
DISC SKIP
REC/PAUSE
DIRECTION
YMERSION
BASS BOOST
MUSIC
POWER SLEEP
INPUT
VOLUME
AB
TAPE
TUNER
CD
/
I
2
1
MODE
2
4
1
6, 11, 22
4
STANDBY indicator
6, 11, 22
E-10
DISC
1
DISC
2
DISC
3
DOWN UP
VOLUME
STANDBY/ON
DIRECTION
YMERSION
B.BOOST
MUSIC
INPUTINPUT
MIN
PRESET
/
TUNING
/
BAND A
/
B
/
C
/
D
/
E
DISC CHANGE OPEN
/
CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSEDOLBY NR
HOUR
RANDOM
REPEAT TIME
DISPLAYMODE
To select the desired track directly
By using the numeric buttons on the remote control, any track
you wish to listen to can be played directly.
Use the numeric buttons to select the desired track number.
Play will begin automatically.
A. For example, to choose track 5
Press 5.
B. For example, to choose track 12
(1) Press +10.
(2) Within a few seconds, press 2.
C. For example, to choose track 20
(1) Press +10.
(2) Within a few seconds, press +10 again.
(3) Within a few seconds, press 0.
Note
If you select a track number higher than the number of tracks
on the disc, only the last track of the disc may be played.
Press DISC SKIP on the remote control once or more (so that
the corresponding disc number is located on the top of the
disc indicator (
3)).
Pressing DISC (1, 2 or 3) will select the disc directly, and play
will begin from track 1 automatically.
To select another disc
Compact disc player operation
DISC CHANGE
DISC (1, 2, 3)
/
( )
( )
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+
I0
E
MODE REPEAT
RANDOM
TUNER
DISC SKIP
REC/PAUSE
DIRECTION
YMERSION
BASS BOOST
MUSIC
POWER SLEEP
INPUT
VOLUME
AB
TAPE
TUNER
CD
/
I
DISC SKIP
( )
Numeric
buttons
( )
To play the desired track (Skip)
Press to skip forward or to skip backward.
Press once for each track to be skipped.
Note
This function can also be performed while the CD player is
stopped. Press
/ when the desired track number appears
on the track number display. Play will begin from the beginning
of the track.
To advance or reverse play rapidly
(Search)
Press and hold to advance play rapidly, and to
reverse play rapidly.
To exchange a disc (or discs) while
playing (PLAYXCHANGE)
During play, you can open the disc tray by pressing DISC
CHANGE without interrupting play. However, in this case,
pressing DISC SKIP or DISC (1, 2 or 3) is invalid.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Yamaha GX-500 Ohjekirja

Kategoria
CD players
Tyyppi
Ohjekirja
Tämä käsikirja sopii myös