Yamaha C961 - DVD Changer Ohjekirja

Kategoria
CD players
Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

i
DVD AUDIO/VIDEO SA-CD CHANGER
U
DVD-C961
STANDBY/ON
PLAYXCHANGE
DISC
SA-CD
DVD-AUDIO
MULTI CH
AUDIO DIRECT
HDMI
DOWN MIX
i
IMPORTANT SAFETY INSTRUCTIONS
Explanation of Graphical Symbols
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert you to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert you
to the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at the plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for a long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15 Be sure to allow spaces of at least 2.5 cm (1 inch)
above, behind and on both sides of this unit.
16 Do not place the following objects on this unit:
A vessel with water in it. If the vessel falls by
vibrations and water spills, it may cause damage to
the unit, and/or you may get an electric shock.
Apparatus shall not be exposed to dripping or
splashing.
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of this unit.
Retain this owner’s manual in a safe place for future
reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
ii
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most
out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear
without annoying blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic
Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from
excessive volume levels.
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the cover
or attempt to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not
place your eyes close to the opening of the disc tray and
other openings or look inside.
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded
cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow
instructions could void your FCC authorization to use this product in the USA.
3.
NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference
will not occur in all installations. If this product is found to be the source of interference, which can be determined by
turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe
Ave. Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
LASER
Type Semiconductor laser GaAlAs
Wave length 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD/VCD/CD)
Beam divergence 60 degrees
iii
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5 cm (1 inch) of free space all around this
unit for adequate ventilation.
3
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in an
environment with high humidity (i.e., a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage
to this unit, and/or personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit
may be exposed to liquid dripping or splashing. On
the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or
personal injury.
Containers with liquid in them, as they may
fall, spilling the liquid and causing an
electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9
Do not use excessive force on switches, knobs and/or
cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of
this unit with a voltage other than as specified.
13 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reason.
14 When not planning to use this unit for long periods
of time (i.e., vacation), disconnect the AC power
plug from the wall outlet.
15 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
16 Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect the
AC power plug from the wall outlet.
17 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
18 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like.
Be sure to place this unit on a level surface.
If you do not do so, the PLAYXCHANGE operation of
this unit may not function correctly, and may damage
the disc(s) and/or this unit itself.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
The unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off by STANDBY/ON.
This state is called the standby mode. In this state, this
unit is designed to consume a very small quantity of
power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug
to wide slot and fully insert.
This Class B digital apparatus complies with
Canadian ICES-003.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
Contents
English
1 En
Introduction ...................................3
Region codes ...............................................3
Supplied accessories ..................................3
Cleaning discs..............................................3
Playable disc formats ..................................3
Patent information .......................................4
Functional Overview .....................5
Front panel ...................................................5
Remote control.............................................6
Rear panel..................................................... 8
Connections...................................9
General notes on connections ...................9
Audio connections.......................................9
Digital connections..............................................9
Analog connections ...........................................10
Video connections .....................................11
S-video jack <A> ..............................................11
Composite video jack <B>................................11
Component video jacks <C>.............................11
HDMI connection........................................12
HDMI jack.........................................................12
HDMI output.....................................................12
Other connection ....................................... 14
Remote control jacks.........................................14
Connecting the power cable .....................14
Getting Started ............................15
Step 1: Inserting batteries into the
remote control............................................15
Using the remote control ...................................15
Step 2: Turning on the Power ...................15
Step 3: Setting language preference........16
Setting the OSD language .................................16
Setting the audio, subtitle and disc menu
languages...........................................................16
Disc Operation.............................17
Basic operation ..........................................17
Selecting a track/chapter ...................................17
Searching backward/forward.............................17
Repeat/Shuffle functions...........................18
Repeat playback ................................................18
Repeating a section within a chapter/track........18
Shuffle playback (except DVD/VCD/SVCD)...19
Preview functions (DVD/VCD/SVCD/CD)
... 19
Previewing DVD/VCD/SVCD .........................19
Previewing CD..................................................20
Previewing VR format ......................................20
On-screen display (OSD) functions
(DVD/VCD/SVCD/CD)................................. 20
Selecting the title/chapter/track
(DVD/VCD/SVCD)..........................................21
Searching for a time (DVD/VCD/SVCD) ........21
Selecting the audio/subtitle/angle (DVD).........21
Selecting the repeat mode and time display
(DVD/VCD/SVCD)..........................................21
Selecting the title/group and searching
for a time (DVD-Audio) ...................................21
Selecting the time display (CD)........................22
Operations for video playback
(DVD-Video/VCD/SVCD) ............................ 22
Playback in slow motion...................................22
Frame-by-frame playback
(DVD-Video/VCD/SVCD/DivX
®
) ..................22
Zooming pictures in/out....................................22
Resuming playback from the last stopped point
...22
Special DVD-Video features...................... 23
Using the disc menu..........................................23
Selecting the camera angle................................23
Selecting the audio language/format and
subtitle language ...............................................23
Special VCD/SVCD features...................... 23
Using the playback control (PBC) menu ..........23
Special DVD-Audio features ..................... 24
Changing pages.................................................24
Playing bonus groups........................................24
Special SA-CD features............................. 24
Changing the playback layer and area ..............24
Playing data discs (MP3/WMA/JPEG/
DivX
®
) ......................................................... 25
Selecting a folder and track/file ........................25
Special picture disc features.................... 25
Using the preview function...............................25
Zooming pictures in ..........................................26
Rotating pictures (JPEG) ..................................26
Selecting scan effect (JPEG).............................26
Playing MP3 music and JPEG pictures
simultaneously ..................................................26
Special DivX
®
features.............................. 26
Using the interactive menu ...............................26
Selecting the audio/subtitle language................26
Contents
Contents
2 En
Setup Menu..................................27
Menu overview ...........................................27
Setup menu operation ...............................28
General setup menu ..................................28
Selecting DVD-Audio/Video mode ..................28
Locking/Unlocking the disc for viewing...........29
Programming tracks and discs...........................29
OSD language ...................................................30
Turning the screen saver on/off.........................30
Setting the sleep timer.......................................30
Turning the auto standby function on/off..........31
Displaying the DivX
®
VOD registration
code ...................................................................31
Audio setup menu......................................31
Setting the analog output...................................31
Setting the digital output ...................................32
Setting the HDMI audio output.........................32
Turning the speaker setup on/off.......................32
Setting the speaker channels .............................33
Setting the CD upsampling ...............................33
Turning the night mode on/off ..........................34
Video setup menu ......................................34
Setting a color system for your TV ...................34
Setting the TV display.......................................35
Turning the black level on/off...........................35
Turning the closed caption on/off .....................35
Adjusting the picture settings............................36
Adjusting the advanced picture settings............36
Turning the progressive scan function on/off ...38
Preference setup menu .............................38
Audio, subtitle, disc menu.................................38
Restricting playback with parental control........38
Selecting the PBC (playback control)
function..............................................................39
Selecting the MP3/JPEG menu .........................39
Selecting playback of VR format......................39
Changing the password .....................................39
Displaying DivX
®
external subtitle files ..........40
Resetting the system..........................................40
Language Codes ......................... 41
Troubleshooting.......................... 42
Glossary....................................... 44
Specifications.............................. 46
3 En
Introduction
English
Thank you for purchasing this unit. This
owner’s manual explains the basic operation
of this unit.
This manual is printed prior to production.
Design and specifications are subject to
change in part as a result of improvements,
etc. In case of differences between the manual
and the product, the product has priority.
This unit is designed to support the region
management system. Check the regional code
number on the DVD disc package. If the
number does not match the region code of this
unit (see the table below or the back of this
unit), this unit may be unable to play the disc.
Remote control
Two batteries (AA, R6, UM-3) for the
remote control
Audio/Video cable
Power cable
Owner’s manual
When a disc becomes dirty, clean it with a
cleaning cloth. Wipe the disc from the center
out. Do not wipe in a circular motion.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or
antistatic spray intended for analog records.
This unit is designed for use with discs having
the logos shown below. Do not attempt to load
any other type of disc into this unit.
This unit can play:
DVD-RW discs recorded in VR format
(compatible with CPRM)
MP3, WMA and JPEG files recorded on
CD-R/RW, DVD-R/RW, DVD+R/RW
KODAK picture CDs, FUJICOLOR CDs
ISO 9660 Level1/Level2 for CD-R/RW
Maximum 30 character display
•DivX
®
files recorded on CD-R/RW,
DVD-R/RW, DVD+R/RW
Official DivX
®
Ultra Certified product
Plays all versions of DivX
®
video (including
DivX
®
6) with enhanced playback of DivX
®
media files and the DivX
®
Media Format
CD-R/RW, DVD-R/RW and DVD+R/RW
/R DL
cannot be played unless finalized.
Progressive JPEG and copyright-protected WMA
files cannot be played with this unit.
Some discs cannot be played depending on disc
characteristics or recording conditions.
Be sure to use only CD-R/RW, DVD-R/RW and
DVD+R/RW discs made by reliable manufacturers.
Do not use any non-standard shaped discs
(heart-shaped, etc.).
Do not use discs with tape, seals, paste or many
scratches on their surface.
Do not use discs affixed with labels printed by a
commercially available label printer.
For details about playable formats, see
“Specifications” on page 46.
Region codes
Destination
Region
code of
this unit
Playable
discs
U.S.A.,
Canada
Supplied accessories
Cleaning discs
1
1
ALL
Playable disc formats
Notes
Introduction
4 En
Introduction
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.
DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license.
“DCDi” is a trademark of Faroudja, a division of Genesis Microchip, Inc.
HDMI, the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Patent information
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
5 En
Functional Overview
English
1 Disc tray
Loads up to 5 discs in the disc tray.
2
Opens or closes the disc tray.
3 STANDBY/ON
Turns on this unit or sets it to the standby mode.
4 DISC 1-5 indicators
Select and directly play back the preferred disc.
Each indicator lights up in green when this unit
recognizes that the corresponding disc has been
loaded.
5 SA-CD indicator
Lights up when the unit detects SA-CD signals
(see page 24).
6 MULTI CH indicator
Lights up when you play multi-channel audio
source.
7 DVD-AUDIO indicator
Lights up when the unit detects DVD-Audio
signals (see page 29).
8 Front panel display
Shows the current status of this unit.
9 AUDIO DIRECT indicator
Lights up when you select the audio direct mode
by pressing AUDIO DIRECT on the remote
control (see page 7).
0 DOWN MIX indicator
Lights up when playing the disc that allows
down mixing of the DVD-Audio multi-channel
source (see page 10).
q HDMI indicator
Lights up when an HDMI component is
connected, and signals output via the HDMI
jack of this unit.
w b/w
Moves to the previous (or top of the currently
playing) chapter or track.
Searches backward.*
e f/ a
Moves to the next chapter or track.
Searches forward.*
r p/ e
Starts or pauses playback.
t s
Stops playback.
y PLAYXCHANGE
Reloads or unloads discs without interrupting
current disc playback (see page 17).
* Press and hold the button for about two seconds.
Front panel
STANDBY/ON
PLAYXCHANGE
DISC
SA-CD
DVD-AUDIO
MULTI CH
AUDIO DIRECT
HDMI
DOWN MIX
12
35467890 ytrewq
Functional Overview
6 En
Functional Overview
1 POWER (
|
)
Turns on this unit.
2 SUBTITLE
Selects the subtitle language (see pages 23 and
26).
3 AUDIO
Selects the audio language or format (see
pages 23 and 26).
Changes the SA-CD playback layer (see
page 24).
4 PLAY (
3
)
Starts playback.
5 STOP (
7
)
Stops playback.
6 SHUFFLE
Accesses or exits from the shuffle mode (see
page 19).
7 SCAN
Previews the content of a chapter/track or whole
disc (DVD/VCD/SVCD) (see page 19).
Plays the first 6 seconds or less of each track
(CD) (see page 20).
8 TOP MENU/RETURN
Displays the top-level disc menu (DVD).
Moves back to the previous menu (VCD) (see
page 23).
9
2
/
3
/5/
Selects an item in the currently displayed menu.
Search or slow playback.
ENTER
Confirms the menu selection.
0 MENU
Displays the menu of a disc (DVD/JPEG) (see
pages 23 and 25).
Switches PBC on or off (VCD/SVCD) (see
page 23).
Remote control
POWER
SUBTITLE
SHUFFLE REPEAT
ON SCREEN
MENU SETUP
SOUND MODEAUDIO DIRECT
TOP MENU
/ RETURN
AUDIO
SKIP
STOP PLAY
SCAN A-B
PAUSE
ZOOM ANGLE
STANDBY
PAG E
DISC
DISC
DISC DISC
DISC
DIMMER
DISC SKIP
ENTER
1
2
3
4
5
6
7
8
9
0
q
w
e
r
t
y
u
i
o
p
a
s
d
f
g
h
7 En
Functional Overview
English
q AUDIO DIRECT
Turns off the video output during audio disc
(CD/DVD-Audio/SA-CD) playback in order to
improve audio quality. Press again to turn on the
video output.
This function is not available for HDMI output.
In the AUDIO DIRECT mode, the front panel
display dims to “MODE 2”.
You can turn on or off the AUDIO DIRECT mode
only when playing back CD, DVD-AUDIO, or
SA-CD disc.
The AUDIO DIRECT mode is canceled when
you set this unit to the standby mode.
w Numeric buttons (0-9)
Selects numbered items in the currently
displayed menu.
e PAGE
Selects the DVD-Audio still picture (see
page 24).
r STANDBY ( )
Sets this unit to the standby mode.
t ANGLE
Selects the DVD camera angle (see page 23) and
scan effect for JPEG (see page 26).
y ZOOM
Enlarges or lessens the video image (see
pages 22 and 26).
u SKIP (l22 / 33l )
Moves to the previous (top of the currently
playing)/next chapter or track.
Searches backward/forward (see page 17).*
i PAUSE ( 8 )
Pauses playback temporarily.
Frame-by-frame playback.
o REPEAT
Accesses or exits from the repeat mode (see
page 18).
p A-B
Repeats a specific segment (see page 18).
a ON SCREEN
Accesses or exits from the on-screen display
(OSD) menu during playback (see page 20).
s SETUP
Accesses or exits from the setup menu of this
unit (see page 28).
d SOUND MODE
Selects a sound mode: stereo, virtual surround or
multi-channel.
Changes the SA-CD playback area (see
page 24).
f DIMMER
Selects from three different levels of brightness
for the front panel display:
MODE 1: 70% brightness
MODE 2: 40% brightness and all the indicators
on the front panel turn off.
NORMAL: 100% brightness
g DISC 1-5
Selects and directly plays back the preferred disc
(see page 17).
h DISC SKIP
Selects another disc (see page 17).
* Press and hold the button for about two seconds.
Notes
8 En
Functional Overview
1 AUDIO OUT (6CH DISCRETE) jacks
Connect to the 6-channel input jacks of your AV
receiver (see page 10).
2 AUDIO OUT (MIXED 2CH) jacks
Connect to the audio input jacks of your AV
receiver or stereo system (see page 10).
3 DIGITAL OUT (COAXIAL) jack
Connect to the coaxial input jack of your AV
receiver (see page 9).
4 DIGITAL OUT (OPTICAL) jack
Connect to the optical input jack of your AV
receiver (see page 9).
5 REMOTE CONTROL (ON, OFF) switch
Switches the remote control on or off.
When using REMOTE CONTROL (IN, OUT)
jacks or REMOTE CONTROL (RS-232C)
terminal, set this switch to ON.
6 REMOTE CONTROL (IN, OUT) jacks
Connect to the remote control output/input jack
of your Yamaha AV receiver/component (see
page 14).
7 REMOTE CONTROL (RS-232C) terminal
Use as an expansion terminal for commercial use.
Consult your dealer for details.
8 AC inlet
Connect the supplied power cable (see page 14).
9 VIDEO OUT (S VIDEO) jack
Connect to the S-video input jack of your AV
receiver (see page 11).
0 VIDEO OUT (VIDEO) jack
Connect to the composite video input jack of
your AV receiver (see page 11).
q HDMI jack
Connect to the HDMI input jack of your HDMI
component (see page 12).
w COMPONENT VIDEO OUT (Y, PB, PR)
jacks
Connect to the component input jacks of your
AV receiver (see page 11).
Do not touch the inner pins of the jacks on the rear
panel of this unit. Electrostatic discharge may cause
permanent damage to this unit.
RS-232C terminal
The REMOTE CONTROL (RS-232C) terminal is used in custom installation. Do not connect
any cables to this terminal during normal use.
Rear panel
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
REMOTE CONTROL
OUTONOFF IN
RS-232C
CENTER
L
R
L
R
1234 56 7 8
90 wq
Note
9 En
Connections
English
Be sure to turn off this unit and unplug the
power cable before you make or change
connections.
Depending on the component you want to
connect, there are various ways to make
connections. Possible connections are
described below.
Refer to the manuals supplied with your
other components as necessary to make the
best connections.
Do not connect this unit via your VCR. The
video quality could be distorted by the copy
protection system.
Do not connect the audio out jack of this unit
to the phono in jack of your audio system.
This unit has digital coaxial, digital optical,
analog 6-channel discrete and analog mixed 2-
channel output jacks. Connection depends on
the availability of audio jacks on your
component.
Digital connections
This unit has both coaxial and optical digital
output jacks. Connect the DIGITAL OUT
(COAXIAL) and/or DIGITAL OUT
(OPTICAL) jack of this unit to your AV
receiver equipped with a Dolby Digital, DTS,
or MPEG decoder using a commercially
available coaxial and/or optical cable.
You need to set [DIGITAL OUTPUT] to [ALL]
(see “DIGITAL OUTPUT” on page 32).
If the audio format of the digital output does not
match the capabilities of your receiver, the
receiver produces a distorted sound or no sound
at all. Make sure to select the appropriate audio
format from the menu screen on the disc.
Pressing AUDIO on the remote control once or
more may change not only the audio languages
but also the audio format. The selected format
appears in the front panel display for several
seconds.
SA-CD audio signals are not output at the
DIGITAL OUT jacks.
If you want to enjoy Dolby Digital, DTS and
MPEG format, you must connect this unit to an
AV receiver that supports these formats.
General notes on connections
Audio connections
Notes
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
CENTER
L
R
L
R
C
C
O
O
OPTICAL
IN
COAXIAL
IN
This unit
AV receiver
Speakers
Connections
10 En
Connections
Analog connections
This unit has two types of analog output jacks.
6-channel discrete jacks
If you want to reproduce multi-channel Super
Audio CD (SA-CD) and DVD-Audio, connect
AUDIO OUT (6CH DISCRETE) jacks of this
unit to the corresponding input jacks of your
AV receiver using commercially available
audio pin cables.
y
You can also enjoy Dolby Digital Surround and
DTS Surround formats if your AV receiver does not
support these formats.
In this case, set [ANALOG OUTPUT] to [MULTI-
CHANNEL] (see “Setting the analog output” on
page 31).
Mixed 2-channel jacks
Connect AUDIO OUT (MIXED 2CH) jacks
of this unit to the corresponding input jacks of
your audio component (such as a stereo
amplifier) using the supplied audio/video
cable. You can connect a subwoofer to the
SUBWOOFER jack.
Multi-channel audio signals are down mixed
to 2-channel audio signals. If you play back a
down mix prohibited DVD-Audio, only the
front L/R channel audio is output.
y
When you play back a down mix prohibited
DVD-Audio, “NO DOWN MIX” appears in the
front panel display, and the DOWN MIX indicator
goes out.
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
CENTER
L
R
L
R
RL
FRONT
SURROUND
CENTER
SUBWOOFER
R L
L
L
R
R
L
L
R
R
This unit
AV reveiver
Speakers
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
CENTER
L
R
L
R
CD / DVD
L
L
R
R
RL
This unit
Subwoofer
Stereo
amplifier
Left
speaker
Right
speaker
Audio pin cable
11 En
Connections
English
If your AV receiver has video output jacks,
connect your receiver and then your TV so
that you can use one TV for several different
video sources (LD, VCR, etc.) by simply
switching the input source selector of your
receiver.
This unit has several types of video output
jacks. Use the one that corresponds to the
input jacks of the component to be connected.
S-video jack <A>
S-video connections achieve a clearer picture
than composite video connections by
transmitting video signals on separate wires
for luminance (Y) and chrominance (C).
Connect the VIDEO OUT (S VIDEO) jack of
this unit to an S-video input jack of your AV
receiver and then to that of your TV using a
commercially available S-video cable.
Composite video jack <B>
Connect the VIDEO OUT (VIDEO) jack of
this unit to a video input jack of your AV
receiver and then to that of your TV using the
supplied audio/video cable.
Component video jacks <C>
Component video connections achieve higher
fidelity color reproduction than S-video
connections by transmitting video signals on
separate wires for luminance (Y: green) and
chrominance (P
B: blue, PR: red).
Connect the COMPONENT VIDEO OUT (Y,
P
B, PR) jacks of this unit to component input
jacks of your AV receiver and then to those of
your TV using a commercially available
component cable. Observe the color of each
jack when you make connections.
If your receiver does not have component
output jacks, you can achieve a better video
image by connecting the component output
jacks of this unit directly to the component
input jacks of your TV.
y
If your AV receiver is equipped with the video
conversion function, you can connect the receiver
and your TV using the different cables from shown
above. For details, refer to the manual supplied with
your receiver.
Video connections
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
CENTER
L
R
L
R
<C><A>
PR
Y
PB
PR
Y
PB
S
S
VIDEO
OUT
VIDEO
IN
S VIDEO
OUT
COMPONENT
VIDEO OUT
COMPONENT
VIDEO IN
S VIDEO
IN
COMPONENT
VIDEO IN
S VIDEO
INPUT
VIDEO
INPUT
YPBPR
V
V
<B>
AV receiver
TV
This unit
Video pin cable
12 En
Connections
HDMI jack
HDMI provides high quality digital audio and
video on a single connection.
Connect the HDMI jack of this unit to an
HDMI input jack of your AV receiver, and
then to that of your TV using a commercially
available HDMI cable.
If your receiver does not have an HDMI input
jack, you can achieve a better video image by
connecting the HDMI jack of this unit directly
to the HDMI input jack of your TV.
You need to make appropriate audio connections
if the connected component does not input audio
signals (see “Audio connections” on page 9).
This unit is not compatible with HDCP-
incompatible HDMI or DVI components.
You need a commercially available HDMI/DVI
conversion cable when you connect this unit to
other DVI components. In this case, the HDMI
jack of this unit does not output any audio
signals.
Do not disconnect or turn off the power of the
HDMI/DVI component connected to the HDMI
jack of this unit while data is being transferred.
Doing so may disrupt playback or cause noise.
y
When connecting an HDMI component, refer to the
manual supplied with your component.
HDMI output
HDMI video output
This unit is compatible with the following
video formats: 480p/60 Hz, 576p/50 Hz,
720p/60 Hz, 1080i/60 Hz, and 1080p/60 Hz.
You need to set [HDMI VIDEO] (see page 37).
Depending on the connected DVI component,
black and white in the image may not be distinct.
In that case, adjust the picture setting of the
connected DVI component.
HDMI connection
S VIDEO VIDEO
VIDEO OUT HDMI
MIXED 2CH
OPTICALCOAXIAL
PCM DIGITAL DTS
AUDIO OUT DIGITAL OUT
FRONT SUB WOOFER SURROUND
6CH DISCRETE
P
R PB Y
COMPONENT VIDEO OUT
CENTER
L
R
L
R
HDMI IN
HDMI OUT
HDMI IN
TV
This unit
AV receiver
Speakers
Notes
Notes
13 En
Connections
English
HDMI audio output
*1: If the connected HDMI component does not support bitstream signals (Dolby Digital, DTS, and MPEG), the
audio output is automatically changed from bitstream signals to PCM signals.
*2: If the connected HDMI component does not support multi-channel audio signals, the audio output is
automatically changed from PCM multi-channel signals to PCM stereo signals and 48 kHz/16 bits signals or
less.
*3: If the audio source is prohibited downmixing, the front L/R channel audio and 48 kHz/16 bits signals or less are
output instead of downmixed stereo.
*4: If the connected HDMI component does not support more than 48 kHz, the audio output is automatically
changed to 48 kHz/16 bits signals or less.
*5: If the connected HDMI component does not support the copy control information on disc, HDMI audio is
muted and “AUDIO CANNOT BE OUTPUT FROM HDMI” appears on the bottom of the SA-CD menu.
You need to set [HDMI AUDIO OUT] (see page 32).
Audio format Analog output
HDMI AUDIO
AUTO PCM OFF
DVD-Video
Dolby Digital
Multi-channel
Multi
Dolby Digital*
1,2
PCM Multi-channel*
2
Off
Stereo/V Surr PCM 2-channel
Dolby Digital
2-channel
Multi/Stereo/V Surr Dolby Digital*
1
PCM 2-channel
DTS
Multi-channel
Multi
DTS*
1,2
PCM Multi-channel*
2
Stereo/V Surr PCM 2-channel
DTS 2-channel Multi/Stereo/V Surr DTS*
1
PCM 2-channel
MPEG
Multi-channel
Multi
MPEG*
1,2
PCM Multi-channel*
2
Stereo/V Surr PCM 2-channel
MPEG 2-channel Multi/Stereo/V Surr MPEG*
1
PCM 2-channel
PCM 2-channel*
4
Multi/Stereo/V Surr PCM 2-channel PCM 2-channel
DVD-Audio
Multi-channel
Multi
PCM (PPCM)
Multi-channel*
2,3
PCM (PPCM)
Multi-channel*
2,3
Stereo/V Surr
PCM (PPCM)
2-channel*
3
PCM (PPCM)
2-channel*
3
2-channel*
4
Multi/Stereo/V Surr
PCM (PPCM)
2-channel
PCM (PPCM)
2-channel
CD/MP3/
WMA/DivX
®
2-channel Multi/Stereo/V Surr PCM 2-channel PCM 2-channel
DTS-CD
Multi-channel
Multi
DTS*
1,2
PCM Multi-channel*
2
Stereo/V Surr PCM 2-channel
2-channel Multi/Stereo/V Surr DTS*
1
PCM 2-channel
VCD 2-channel Multi/Stereo/V Surr PCM 2-channel PCM 2-channel
SVCD
Multi-channel
Multi
MPEG*
1,2
PCM Multi-channel*
2
Stereo/V Surr PCM 2-channel
2-channel Multi/Stereo/V Surr MPEG*
1
PCM 2-channel
SA-CD
Multi-channel area Multi
PCM
Multi-channel*
2,5
PCM
Multi-channel*
2,5
Stereo area Stereo/V Surr PCM 2-channel*
5
PCM 2-channel*
5
Note
14 En
Connections
Remote control jacks
This unit has remote control input/output
jacks. If your AV receiver is a Yamaha product
and has the capability to transmit of SCENE
control signals, you can use the SCENE
function.
Connect the REMOTE CONTROL (IN) jack
of this unit to a remote control output jack of
your receiver using a commercially available
monaural mini-jack cable so that this unit
starts playback automatically by simply
pressing a button of your receiver.
When using the REMOTE CONTROL (IN,
OUT) jacks, set the REMOTE CONTROL
(ON, OFF) switch to ON.
y
For details about the SCENE function, refer to
the owner’s manual supplied with your Yamaha
AV receiver.
The REMOTE CONTROL (IN, OUT) jacks are
also used in custom installation.
After all other connections are complete, plug
the supplied power cable into the AC inlet of
this unit and then plug the power cable to an
AC outlet.
Other connection
REMOTE CONTROL
OUTONOFF IN
RS-232C
REMOTE OUT
This unit
AV receiver
Connecting the power cable
REMOTE CONTROL
OUTONOFF IN
RS-232C
This unit
To an AC outlet
15 En
Getting Started
English
You can customize the various settings of this
unit using the setup menu.
y
If the setting you have selected are not appropriate,
you can reset all settings to the initial factory
settings (see “Resetting the system” on page 40).
1 Open the battery compartment.
2 Insert the two supplied batteries (AA, R6,
UM-3) following the indications (+/–)
inside the compartment.
3 Close the cover.
Insert batteries correctly according to the polarity
markings (+/–). Batteries inserted in the opposite
orientation may leak.
Replace the exhausted batteries immediately with
new ones to prevent leakage.
Remove the batteries from the compartment if the
remote control is not used for more than a month.
If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material
or letting it come into contact with clothing, etc.
Clean the battery compartment thoroughly before
installing new batteries.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as
alkaline and manganese batteries) together. Read
the packaging carefully as these different types of
batteries may have the same shape and color.
Dispose of the batteries correctly in accordance
with your local regulations.
Using the remote control
Use the remote control within 6 m
(approximately 20 ft) of this unit and point it
toward the remote control sensor.
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
places of high humidity, such as near a bath
places of high temperature, such as near a
heater or stove
places of extremely low temperature
dusty places
1 Make sure the power cable is plugged into
an AC outlet.
2 Turn on your TV and AV receiver.
3 Select the appropriate input source of the
AV receiver (refer to the manual supplied
with your AV receiver).
4 Press STANDBY/ON on the front panel or
POWER (
|
) on the remote control to turn
on this unit.
The front panel display lights up.
5 Set the TV to the correct video input (refer
to the manual supplied with your TV).
The default screen appears on the TV.
Step 1: Inserting batteries into
the remote control
Notes
2
1
3
2
Notes
Step 2: Turning on the Power
Within 6 m
(approximately 20 ft)
Getting Started
16 En
Getting Started
You can customize this unit using the setup
menu displayed on the TV screen.
y
Unless stated otherwise, all operations described
here are carried out using the supplied remote
control.
To return to the previous menu, press
2
.
To exit from the menu, press SETUP.
To change settings other than [OSD
LANGUAGE], [AUDIO], [SUBTITLE] and
[DISC MENU], refer to “Setup Menu” on
page 27.
Setting the OSD language
You can select your own preferred language
for the setup menu. This setting remains once
selected.
1 Press SETUP.
2 Press
2
/
3
to select “GENERAL SETUP
PAGE”.
3 Press 5/ to highlight [OSD
LANGUAGE], and then press
3
.
4 Press 5/ to select a language, and then
press ENTER.
Setting the audio, subtitle and disc
menu languages
You can select your own preferred language for
the audio, subtitle and disc menu. This unit
automatically switches to the selected language
whenever you load a disc. If the selected
language is not available on the disc, the default
language of the disc will be used instead.
These settings are only available for DVD-
Video discs.
1 Press STOP (
7
) twice, and then press
SETUP.
2 Press
3
repeatedly to select
“PREFERENCE PAGE”.
3 Press 5/ to highlight one of the
following options, and then press
3
.
AUDIO (audio language)
SUBTITLE (subtitle language)
DISC MENU (disc menu language)
4 Press 5/ to select a language, and then
press ENTER.
5 Repeat steps 3-4 for other language
settings.
To select a language not in the list
1 Select [OTHERS] in [AUDIO] or
[SUBTITLE] or [DISC MENU].
2 Use the numeric buttons (0-9) to enter
the 4-digit language code (see “Language
Codes” on page 41), and then press
ENTER.
Step 3: Setting language
preference
GENERAL SETUP PAGE
DVD-AUDIO
DISC LOCK
PROGRAM
OSD LANGUAGE ENGLISH
SCREEN SAVER FRANÇAIS
SLEEP ESPAÑOL
AUTO STANDBY
DIVX(R) VOD CODE
PREFERENCE PAGE
AUDIO ENGLISH
SUBTITLE CHINESE
DISC MENU FRENCH
PARENTAL SPANISH
PBC PORTUGUESE
MP3/JPEG NAV POLISH
VR LIST ITALIAN
PASSWORD TURKISH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Yamaha C961 - DVD Changer Ohjekirja

Kategoria
CD players
Tyyppi
Ohjekirja
Tämä käsikirja sopii myös