Simplicity 12.5HP / 40" MOWER Ohjekirja

Kategoria
Lawnmowers
Tyyppi
Ohjekirja

Tämä käsikirja sopii myös

Instruction Book - Riding Mower Model 405013x50C
Manuel de l’utilisateur - Tondeuse autoportée modèle 405013x50C
Betriebsanleitung - Aufsitzmäher Modell 405013x50C
Istruzioni per l’uso - Trattore tagliaerba Modello 405013x50C
Gebruikshandleiding - Zitmaaier model 405013x50C
Driftsvejledning - Plænetraktor Model 405013x50C
Bruksanvisning - Rider modell 405013x50C
Användarhandbok - Trädgårdtraktor modell 405013x50C
Käyttöohjeet - Ajettava ruohonleikkuri, malli 405013x50C
Manual de instrucciones - Cortacésped autoportado Modelo 405013x50C
Juhend - Traktorniiduki mudel 405013x50C
Åã÷åéñßäéï ïäçãéþí ÷ñÞóçò -
ÌïíôÝëï ÷ïñôïêïðôéêïý ãéá åðï÷ïýìåíï ÷åéñéóôÞ 405013x50C
Használati Útmutató - Önjáró fûnyíró gép 405013x50C modell
Instrukciju grāmata - Braucošs pļāvēja modelis 405013x50C
Instrukcija - Sėdimoji žoliapjovė modelis 405013x50C
Instrukcja - Kosiarka z siedziskiem model 405013x50C
Návod k použití - Traktorová sekaèka, model 405013x50C
F
D
I
NL
DK
N
S
SF
GB
E
EE
GR
H
LV
LT
PL
1740475 TP 199--4493--01--LT--L
CZ
2
1740475
1
1
2
3
4 (17x192)
6
7 (17x195)
5 (30x49)
2
1
2
3
4 (17x47
5 (1001054)
1
2
3
3
7
6 (17x146)
4 (25x3)
5
1
3
4
2
6
8
6 (2x82)
7 (14x79)
4
3
6
1
2
4
5
7
5
1
2
6
1
2
3
4
5
6
7
7
1
8
2
1
2
3
4
5
9
4
5
4
6
1
2
3
7
10
1
2
3
4
5
6
7
11
2
3
1
12
1
2
13
14
1
2
15
3
1740475
1
2
16
3
4
1
17
2
1
2
3
4
5
18
3
2
1
19
1
2
3
4
20
21
13
2
1
2
3
3
4
4
5
6
7
8
9
22
4
1740475
12 3
4
5
6
7
9
23
8
10
MAX 90N
+
MAX 150N
+
11 12
13
14
1
2
3
4
5
67
8
9
10 11 12
13
14
15
24
25
1001054
2x82
14x79
17x47
20729
30x49
17x195
17x192
17x146
25x3
GB
5
1740475
CONTENTS
INTERNATIONAL PICTORIALS 5
OWNER’S INFORMATION 6
SAFE OPERATION PRACTICES 6
ASSEMBLY 7
OPERATION 8
MAINTENANCE CHART 10
MAINTENANCE 10
TROUBLE SHOOTING CHART 10
INTERNATIONAL PICTORIALS
IMPORTANT: The following pictorials are lo-
cated on your unit or on literature supplied
with the product. Before you operate the
unit, learn and understand the purpose for
each pictorial.
NOTE: Illustrations and pictorials begin
on page 2.
Safety Warning Pictorials (Figure 23)
1 WARNING
2 IMPORTANT: Read Owner’s Manual
Before Operating This Machine.
3 WARNING: Thrown Objects. Keep
Bystanders Away. Read User Instructions
Before Operating This Machine.
4 WARNING: Do Not Use This Machine On
Slopes Greater Than 10 Degrees.
5 DANGER: Keep People, Especially
Children, Away From Unit.
6 DANGER: No Step.
7 DANGER: Keep Feet And Hands Away
From Rotating Blade.
8 Declared airborne sound power level of 100
dB(A) is in accordance with Directive
2000/14/EC.
9 DANGER: Disconnect S park Plug Wire
Before Servicing Unit.
10 WARNING: Hot Surface.
11 WARNING: Maximum loading when using
attachments.
12 WARNING: Crushed Fingers.
13 IMPORTANT: Follow Instructions In
Owner’s Manual To Level The Deck.
14 WARNING: Stay Clear Of Mower Blade As
Long As Engine Is Running.
Control And Operating Pictorials
(Figure 24)
1 Engine Start
2 Lights
3 Engine Run
4 Engine Stop
5 Engine Run
6 Brake
7 Parking Brake
8 Clutch
9 Slow
10 Fast
11 Choke
12 Oil
13 Blade Rotation Control
14 Raise
15 Fuel
Declared vibration e mission values in accordance with Directive 98/37/EC.
Vibration Emission according to BS EN 1032: Seat 2
m/s
2
,
Right Running Board 2,9 m/s
2
, Left Running Board 3,3 m/s
2
Vibration Emission according to BS EN 1033: Steering Wheel 3,5 m/s
2
Values determined with operator in operating position when the machine was
operated stationary on a concrete surface at 2850 min--1.
MODEL NO.: 405013X50C
SERIAL NO.:
2850 RPM
172 kg
SKU No.:
YYYY MM DD:
www.briggsandstratton.com
Net kW 6.39
Assembled in Lawrenceburg, TN 38464; USA
by Swisher, Inc. for Briggs & Stratton Corporation
Declared airborne sound power level of 100 dB(A) is in accordance with Directive
2000/14/EC.
Sound Pressure Level at operator position 83 dB.
Values determined at ear according to the specifications of EN 836/A2:2001.
GB
6
1740475
OWNER’S INFORMATION
Know your product: If you understand the unit
and how the unit operates, you will get the best
performance. As you read this manual, compare
the illustrations to the unit. Learn the location
and the function of the controls. To help prevent
an accident, follow the operating instructions
and the safety rules. Keep this manual for future
reference.
WARNING: Look for this symbol to indicate
important safety precautions. This symbol
indicates: “Attention! Become Alert! Your
Safety Is At Risk.”
Responsibility Of The Owner
WARNING: This cutting machine is
capable of amputating hands and
feet and throwing objects. Failure
to observe the following safety instructions
could result in serious injury or death to
the operator or bystanders.
The responsibility of the owner is to
follow the instructions below.
SAFE OPERATION PRACTICES
For Ride--On (Riding)
Rotary Mower Machines
Training
1. Read the instructions carefully. Be familiar
with the controls and the proper use of the
equipment.
2. Never allow children or people unfamiliar
with these instructions to use the mower.
Local regulations may restrict the age of
the operator.
3. Never mow while people, especially
children, or pets are nearby.
4. Keep in mind that the operator or user is
responsible for accidents or hazards occur-
ring to other people or their property.
5. Do not carry passengers.
6. All drivers should seek and obtain pro-
fessional and practical instruction. Such
instruction should emphasize:
a. the need for care and concentration
when working with ride--on machines;
b. control of a ride--on machine sliding
on a slope will not be regained by the
application of the brake. The main
reasons for loss of control are:
insufficient wheel grip;
being driven too fast;
inadequate braking
the type of machine is unsuitable
for its task;
lack of awareness of the effect of
ground conditions, especially
slopes;
incorrect hitching and load dis-
tribution.
Preparation
1. While mowing, always wear substantial
footwear and long trousers. Do not operate
the equipment when barefoot or wearing
open sandals.
2. Thoroughly inspect the area where the
equipment is to be used and remove all ob-
jects which may be thrown by the machine.
3. WARNING -- Petrol is highly flammable.
a. Store fuel in containers specifically de-
signed for this purpose.
b. Refuel outdoors only and do not
smoke while refuelling.
c. Add fuel before starting the engine.
Never remove the cap of the fuel tank
or add petrol while the engine is run-
ning or when the engine is hot.
d. If petrol is s pilled, do not attempt to
start the engine but move the machine
away from the area of spillage and
avoid creating any source of ignition
until petrol vapours have dissipated.
e. Replace all fuel tanks and container
caps securely.
4. Replace faulty silencers.
5. Before using, always visually inspect to see
that the blades, blade bolts and cutter as -
sembly are not worn or damaged. Replace
worn or damaged blades and bolts in sets
to preserve balance.
6. On multi--blade machines, take care as ro-
tating one blade can cause other blades to
rotate.
Operation
1. Do not operate the engine in a confined
space where dangerous carbon monoxide
fumes can collect.
2. Mow only in daylight or in good artificial
light.
3. Before attempting to start the engine, dis-
engage all blade attachment clutches and
shift into neutral.
4. Do not use on slopes of more than 10 de-
grees.
5. Remember there is no such thing as a
“safe” slope. Travel on grass slopes re-
quires particular care. To guard against
overturning:
a. do not stop or start suddenly when
going up or downhill;
b. engage clutch slowly, always keep
machine in gear, especially when tra-
velling downhill;
c. machine speeds should be kept low
on slopes and during tight turns;
d. stay alert for humps and hollows and
other hidden hazards;
e. never mow across the face of the
slope, unless the mower is designed
for this purpose.
6. Use care when pulling loads or using heavy
equipment.
a. Use only approved drawbar hitch
points.
b. Limit loads to those you can safely
control.
c. Do not turn sharply. Use care when
reversing.
d. Use counterweight(s) or wheel
weights when suggested in the In-
struction Book.
7. Watch out for traffic when crossing or near
roadways.
8. Stop the blades rotating before crossing
surfaces other than grass.
9. When using any attachments, never direct
discharge of material toward bystanders
nor allow anyone near the machine while in
operation.
10. Never operate the mower with defective
guards or shields, or without safety protec-
tive devices in place.
11. Do not change the engine governor set-
tings or overspeed the engine. Operating
an engine at excessive speed may in-
crease the hazard of personal injury.
12. Before leaving the operator’s position
a. disengage the power take--off and
lower the attachments;
b. change into neutral and set the park-
ing brake;
c. stop the engine and remove the key.
13. Disengage drive to attachments, stop the
engine, and disconnect the spark plug
wire(s) or remove the ignition key
a. before cleaning blockages or unclog-
ging chute;
b. before checking, cleaning or working
on the mower;
c. after striking a foreign object. Inspect
the mower for damage and make re-
pairs before restarting and operating
the equipment;
d. if the machine starts to vibrate abnor-
mally (check immediately).
14. Disengage drive to attachments when
transporting or not in use.
15. Stop the engine and disengage drive to at-
tachment
a. before refuelling;
b. before removing the grass catcher;
c. before making height adjustment un-
less adjustment can be made from the
operator’s position.
16. Reduce the throttle setting during engine
run--out and, if the engine is provided with a
shut--off valve, turn the fuel off at the con-
clusion of mowing.
17. Before and when backing, look behind and
down for s mall children.
18. Use extra care when approaching blind
corners, shrubs, trees or other objects that
may obscure vision.
Maintenance and Storage
1. On multi--blade machines, take care as ro-
tating one blade can cause other blades to
rotate.
2. When machine is to be parked, stored or
left unattended, lower the cutting means
unless a positive mechanical lock is used.
3. Keep all nuts, bolts, and screws tight to be
sure the equipment is in safe working
condition.
4. Never store the equipment with petrol in the
tank inside a building where fumes may
reach an open flame or spark.
5. Allow the engine to cool before storing in
any enclosure.
6. To reduce the fire hazard, keep the engine,
silencer, battery compartment and petrol
storage area free of grass, leaves, or ex-
cessive grease.
7. Check the grass catcher frequently for
wear or deterioration.
8. Replace worn or damaged parts for safety.
9. If the fuel tank has to be drained, this
should be done outdoors.
GB
7
1740475
ASSEMBLY
All fasteners are in the parts bag. Do not discard
any parts or material until the unit is assembled.
WARNING: Before doing any as-
sembly or maintenance to the
mower, remove the wire from the
spark plug.
NOTE: In this instruction book, left and right
describe the location of a part with the oper-
ator on the seat.
NOTE: Illustrations and pictorials begin on
page 2.
NOTE: To assemble the following loose
parts, use the fasteners shown at full size in
Figure 25.
How To Install The Front Wheels
(Figure 1)
Use a knife and cut the four sides of the con-
tainer. Install the front wheels (1) in the con-
tainer.
NOTE: Use a piece of wood about 4 feet (1.25
meters) long to raise the front of the tractor.
If a piece of wood cannot be found, get
another person to help lift the tractor. Be
careful, do not let the tractor fall.
1. Raise the front of the tractor. Set a s upport
(block of wood) under the tractor.
2. Make sure the valve stem (2) is to the out-
side of the tractor. Slide the front wheel (1)
on the spindle (3).
3. Fasten each front wheel (1) with washer (4)
and cotter pin (5). Bend the ends of the
cotter pin (5) appart to keep the front wheel
(1) on the spindle (3).
4. After the front wheels (1) are installed, lift
the tractor from the support. Roll the tractor
off of the container.
5. If your tractor has hub caps (6), install the
hub caps (6). Make sure the washers (4)
hold the hub caps (6) in place.
How To Install The Seat (Figure 2)
1. Carefully remove the plastic bag from the
seat (1).
2. Align the holes in the seat hinge (2) to the
holes in the seat (1). Fasten the seat (1) to
the seat hinge (2) with the fasteners (4) and
(5).
3. Check the operating position of the seat (1).
If the seat (1) needs to be adjusted, loosen
the two wing bolts (5). Slide the seat (1) for-
ward or backward along the seat adjusting
holes (3). Tighten the wing bolts (5).
How To Assemble The Steering Wheel
(Figure 3)
1. Make sure the front wheels point forward.
2. Slide the cover (3) over the steering post
(2). Make sure the collar of the cover (3) is
on top.
3. Slide the steering wheel (1) onto the steer-
ing post (2).
4. Attach the steering wheel (1) to the steer-
ing post (2) with screw (4) and washer (6).
5. Some models have an optional insert (7) in
the parts bag. Attach the insert (7) to the
center of the steering wheel (1).
Maintenance Free Battery (Figure 4)
IMPORTANT: Before you attach the battery
cables to the battery, check the battery date.
The battery date tells if the battery must be
charged.
1. Check the top of the battery (1) for the loca-
tion of the battery date.
2. If the battery (1) is put into service before
the , the battery cables can be attached with-
out charging the battery (1). See “How To
Install The Battery Cables”.
3. If the battery (1) is put into service after the ,
the battery (1) must be charged. See “How
To Charge The Maintenance Free Battery”.
How To Charge The Battery (Figure 4)
WARNING: When you charge the
battery, do not smoke. Keep the bat-
tery away from any sparks. The
fumes from the battery acid can cause an
explosion.
1. Remove the battery (1) and battery tray (3).
2. Remove the protective caps from the battery
terminals.
3. Use a 12 volt battery charger to charge the
battery (1). Charge at a rate of 6 amperes
for one hour. If you do not have a battery
charger, have an authorized service centre
charge the battery.
4. Install the battery (1) and battery tray (3).
Make sure the positive (+) terminal (4) is on
the left side.
How To Install The Battery Cables
(Figure 4)
WARNING: To prevent sparks, fasten
the red cable to the positive (+) ter-
minal before you connect the black
cable.
1. Remove the protective caps from the battery
terminals.
2. Slide the terminal cover (2) onto the red
cable (5). Fasten the red cable (5) to the
positive (+) terminal (4) with the fasteners
(6) and (7).
3. Fasten the black cable 8 to the negative (--)
terminal with the fasteners (6) and (7).
Check The Tyres
Check the air pressure in the tyres. Tyres with
too much air pressure will cause the unit to ride
rough. Also, the wrong air pressure will keep the
mower housing from cutting level. The correct
air pressure is: Front Tyres 0,97 BAR (14 PSI),
Rear Tyres 0,69 BAR (10 PSI). The tyres were
over inflated for shipment.
Check The Level Of The Mower
Housing
Make sure the level of cut is still correct. After
you mow a short distance, look at the area that
was cut. If the mower housing does not cut level,
see the instructions on “How To Level The
Mower Housing” in the Maintenance section of
this instruction book.
How To Prepare The Engine
NOTE: The engine was shipped from the fac-
tory filled with oil. Check the level of the oil.
Add oil as needed.
See the engine manufacturer’s instructions for
the type of petrol and oil to use. Before y ou use
the unit, read the information on safety, oper-
ation, maintenance, and storage.
WARNING: Follow the engine manu-
facturer’s instructions for the type o
f
petrol and oil to use. Always use a
safety petrol container. Do not smoke when
adding petrol to the engine. When inside an
enclosure, do not fill with petrol. Before you
add petrol, stop the engine. Let the engine
cool for several minutes.
Important! Before You Start Mowing
U Check the engine oil.
U Fill the fuel tank with petrol.
U Check the air pressure of the tyres.
U Check the level of the mower hous-
ing.
U Attach the battery cables.
GB
8
1740475
OPERATION
NOTE: Illustrations and pictorials begin on
page 2.
Location Of Controls (Figure 5)
Blade Rotation Control (1): Use the blade rota-
tion control to start and stop the rotation of the
blade.
Clutch / Brake Pedal (2): The pedal has two
functions. The first function is a clutch. The sec-
ond function is a brake.
Headlight Switch (3): The headlight switch is
the first part of the ignition switch. To use the
lights with the engine running, turn the key to the
position for the lights.
Ignition Switch (3): Use the ignition switch to
start and stop the engine.
Shift Lever (4): Use the shift lever to change
the speed of the unit.
Lift Lever (5): Use the lift lever to change the
height of cut.
Parking Brake Lever (6): Use the parking brake
lever to engage the brake when you leave the
unit.
Throttle Control Lever (7): Use the throttle
control lever to increase or decrease the speed
of the engine.
Attachments
This unit can use many different attachments.
This unit can pull attachments like a lawn
sweeper, a lawn aerator, or a hopper spreader.
This unit can not use attachments that engage
the ground like a plough, a disk harrow, or a
cultivator.
For trailer and pull--behind attachments, the
maximum weight is 113 kg (250 lbs.).
How To Use The Throttle Control
(Figure 5)
Use the throttle control (7) to increase or de-
crease the speed of the engine.
1. The FAST position is marked with a detent.
For normal operation and when using a
grass bagger, move the throttle control to the
FAST position. For maximum charging of the
battery and for a cooler running engine, oper-
ate the engine in the FAST position.
2. The engine governor is set at the factory for
maximum performance. Do not adjust the
governor to increase the speed of the en-
gine.
How To Use The Blade Rotation Control
(Figure 5)
Use the blade rotation control (1) to engage
the blade(s).
1. Before you start the engine, make sure the
blade rotation control (1) is in the DISEN-
GAGE position.
2. Move the blade rotation control (1) to the
ENGAGE position to rotate the blade(s).
NOTE: If the engine stops when you en-
gage the blade(s), the seat switch is not
activated. Make sure you sit in the middle
of the seat.
3. Move the blade rotation control (1) to the
DISENGAGE position to stop the blade(s).
Before you leave the operator’s position,
make sure the blade(s) has stopped rotating.
4. Before you ride the unit across a sidewalk or
a road, move the blade rotation control (1)
to the DISENGAGE position.
WARNING: Always keep your
hands and feet away from the
blade, deflector opening, and the
mower housing when the engine runs.
How To Use The Shift Lever (Figure 5)
To change the forward speed or the direction of
the unit, follow the steps below.
CAUTION: Before you move the shift lever,
completely push the clutch/brake pedal for-
ward to stop the unit. If the unit is not
stopped, the gearbox can be damaged.
1. Completely push the clutch/brake pedal (2)
forward to stop the unit. Keep your foot on
the pedal.
2. Move the throttle control lever (7) to the
SLOW position.
3. To go forward, move the shift lever (4) to a
forward speed setting. To go backward,
move the shift lever (4) to reverse.
4. Slowly release the clutch/brake pedal (2).
Do not keep your foot on the pedal.
5. Move the throttle control (7) to the FAST
position.
How To Use The Parking Brake
(Figure 5)
1. Completely push the clutch/brake pedal (2)
forward.
2. Lift the parking brake lever (6).
3. Remove your foot from the clutch/brake
pedal (2) and then release the parking
brake lever (6). Make sure the parking brake
will hold the unit.
4. To release the parking brake (6), completely
push the clutch/brake pedal (2) forward.
The parking brake will automatically release.
WARNING: Before you leave the
operator’s position, move the shift
lever to the neutral (N) position. Set
the parking brake. Move the blade rotation
control to the DISENGAGE position. Stop
the engine and remove the ignition key.
How To Change The Cutting Height
(Figure 5)
To change the cutting height, raise or lower the
lift lever (5) as follows.
1. Move the lift lever (5) forward t o lower the
mower housing and back to raise the mower
housing.
2. When you ride on a sidewalk or road, move
the lift lever (5) to the highest position and
move the blade rotation control to the DIS-
ENGAGE position.
How To Stop The Unit (Figure 5)
1. Completely push the clutch/brake pedal (2)
forward to stop the unit. Keep your foot on
the pedal.
2. Move the blade rotation control (1) to the
DISENGAGE position.
3. Move the shift lever (4) to the NEUTRAL
position.
4. Set the parking brake (6).
WARNING: Make sure the parking
brake will hold the unit.
5. Move the throttle control (7) to the SLOW
position.
6. To stop the engine, turn the ignition key (3)
to the OFF position. Remove the k ey.
How To Transport The Unit
To transport the unit, follow the steps below.
1. Move the blade rotation control to the DIS-
ENGAGE position.
2. Raise the lift lever to the highest position.
3. Movethethrottlecontroltoapositionbe-
tween SLOW and FAST.
4. To go faster, move the shift lever to a faster
speed.
How To Operate With The Mower
Housing
IMPORTANT: When you operate with the
mower housing, always operate with the
throttle control in the FAST position.
1. Start the engine.
2. Move the lift lever to a height of cut position.
In high or thick grass, cut the grass in the
highest position first and then lower the
mower housing to a lower position.
3. Move the throttle control to the SLOW posi-
tion.
4. Slowly move the blade rotation control to the
ENGAGE position.
5. Push the c lutch/brake pedal completely for-
ward.
6. Move the s hift lever to one of the s peed set-
tings.
NOTE: When you mow in heavy grass or
mow with a bagger, put the shift lever in
the slowest speed.
7. Slowly release the clutch/brake pedal.
8. Move the throttle control to the FAST posi-
tion. If you need to go faster or slower, stop
the unit and move the shift lever to another
speed setting.
9. Make sure the level of cut is still correct.
After you mow a short distance, look at the
area that was cut. If the mower housing does
not cut level, see the instructions on “How To
Level The Mower Housing” in the Mainten-
ance section.
WARNING: For better control of the
unit, select a safe speed.
How To Operate On Hills
WARNING: Do not ride up or down
slopes that are too steep to back
straight up. Never ride the unit
across a slope.
1. Before you ride up or down a hill, move the
shift lever to the slowest speed.
2. Do not stop or change speed settings on a
hill. If you must s top, quickly push the clutch/
brake pedal forward and set the parking
brake.
GB
9
1740475
3. To start again, make sure the shift lever is in
the slowest speed. Move the throttle control
to the SLOW position. Slowly release the
pedal.
4. If you must stop or start on a hill, always
have enough space for the unit to roll when
you release the brake and engage the clutch.
5. Be very careful when you change directions
on a hill. When on a s lope or in a turn on a
hill, move the throttle control to the SLOW
position to help prevent an accident.
Before Starting The Engine
Check the oil
NOTE: The engine was shipped from the fac-
tory filled with oil. Check the level of the oil.
Add oil as needed. See the engine manufac-
turer’s instructions for the type of petrol and
oil to use.
1. Make sure the unit i s level.
NOTE: Do not check the level of the oil
while the engine runs.
2. Check the oil. Follow the procedure in the
engine manufacturer’s instructions.
3. If necessary, add oil until the oil reaches the
FULL mark on the dipstick. The quantity of oil
needed from ADD to FULL is shown on the
dipstick. Do not add too much oil.
Add Petrol
WARNING: Always use a safety
petrol container. Do not smoke
when adding petrol to the fuel tank.
Do not add petrol when you are inside an
enclosure. Before you add petrol, stop the
engine and let the engine cool for several
minutes.
(Figure 6) Fill the fuel tank (1) to the FULL (2)
position with regular unleaded petrol. Do not use
premium unleaded petrol. Make sure the petrol
is fresh and clean. Leaded petrol will increase
deposits and shorten the life of the valves.
How To Start The Engine
WARNING: The electrical system
has an operator presence system
that includes a sensor switch for
the seat. These components tell the
electrical system if the operator is sitting
on the seat. This system will stop the
engine when the operator leaves the seat.
For your protection, always make sure this
system operates correctly.
NOTE: The engine will not start unless you
depress the clutch/brake pedal and move the
blade rotation control to the DISENGAGE
position.
1. Push the c lutch/brake pedal completely for-
ward. Keep your foot on the pedal.
2. Move the s hift lever to the neutral (N) posi-
tion.
3. Make sure the blade rotation control is in the
DISENGAGE position.
4. Move the throttle control completely forward
to the CHOKE or FAST position. Some mo-
dels have a separate choke knob. Pull the
choke knob to the full CHOKE position.
5. Turn the ignition key to the START position.
NOTE: If the engine does not start after
four or five tries, move the throttle control
to the FAST position. Again try to start the
engine. If the engine will not start, see the
TROUBLE SHOOTING CHART.
6. Slowly move the throttle control to the SLOW
position.
7. To start a hot engine, move the throttle con-
trol to a position between FAST and SLOW.
Mowing And Bagging Tips
1. For a lawn to look better, check the cutting
level of the mower housing. See “How To
Level The Mower Housing” in the Mainten-
ance section.
2. For the mower housing to cut level, make
sure the tyres have the correct amount of air
pressure.
3. Every time you use the unit, check the blade.
If the blade is bent or damaged, immediately
replace the blade. Also, make sure the nut
for the blade is tight.
4. Keep the blade(s) sharpened. Worn blades
will cause the ends of the grass to turn
brown.
5. Do not cut or bag grass that is wet. Wet
grass will not discharge correctly. Let the
grass dry before cutting.
6. Use the left side of the mower housing to trim
near an object.
7. Discharge the cut grass onto the mowed
area. The result is a more even discharge of
cut grass.
8. When you m ow large areas, start by turning
to the right so that the c ut grass will dis -
charge away from shrubs, fences, driveways,
etc. After one or two rounds, mow in the op-
posite direction making left turns until fin-
ished.
9. If the grass is very high, cut two times to de-
crease the load on the engine. First cut with
the mower housing in the highest position
and then lower the mower housing for the
second cut.
10.For better engine performance and an even
discharge of the cut grass, always operate
the engine with the throttle in FAST position.
11. When you use a bagger, operate the engine
with the throttle in FAST position and the shift
lever in first or second gear.
12.For better c utting performance and a quality
cut, mow with the shift lever in one of the
slower speeds.
13.After each use, clean the bottom and top of
the mower housing for better performance.
Also, a clean mower housing will help pre-
vent a fire.
GB
10
1740475
MAINTENANCE CHART
FREQUENCY MAINTENANCE REQUIRED COMMENTS
Daily or before each use Maintenance engine. Refer to the Engine Owner’s Manual.
Examine blade(s).
Check for cracks, wear, and excessive damage.
Remove debris from unit and mowing area.
Examine all rotating and sliding parts.
Check tire inflation. Refer to the Maintenance section.
Verify that the mower housing is level. Refer to the Maintenance section.
Examine V--belts. Check for cracks, wear, and excessive damage.
Check brake operation. Refer to the Operation and Maintenance
sections.
After completion of first 5 hours Change oil. Refer to the Engine Owner’s Manual.
After 25 hours Maintenance engine. Refer to the Engine Owner’s Manual.
Remove, examine, sharpen, and balance
blade(s).
Refer to Maintenance section.
Check adjustments:
a. Blade Rotation Control
b. Brake
c. Clutch
d. Steering
Refer to Maintenance section.
Lubricate chassis and mower housing. Refer to Where to Lubricate instructions.
Check the muffler:
a. Torque
b. For wear or burn out
c. Condition of spark arrestor, (if applicable).
Refer to Maintenance section.
Before storage of 30 days or more Prepare engine for storage. Refer to the Engine Owner’s Manual.
Drain fuel system. Refer to warnings in the Owner’s Manual.
Add fuel stabilizer. Refer to the Engine Owner’s Manual.
Prepare battery for storage:
a. Remove from unit.
b. Fully charge.
c. Move to cool dry place.
MAINTENANCE
NOTE: Illustrations and pictorials begin on
page 2.
General Recommendations
1. The owner’s responsibility is to maintain this
product. This will extend the life of the prod-
uct and is also necessary to maintain war-
ranty coverage.
2. Check the spark plug, drive brake, lubricate
the unit, and clean the air filter once a year.
3. Check the fasteners. Make sure all fasteners
are tight.
4. Follow the Maintenance section to keep the
unit in good operating condition.
WARNING: Before you make an in-
spection, adjustment, or repair to
the unit, disconnect the wire to the
spark plug. Remove the wire from the
spark plug to prevent the engine from
starting by accident.
NOTE: Torque is measured in foot pounds
(metric Nm). This measurement describes
how tight a nut or bolt must be. The torque is
measured with a torque wrench.
Inspect Blade (Figure 7)
WARNING: Before you inspect or
remove the blade, disconnect the
wire to the spark plug. If the blade
hits an object, stop the engine. Check the
unit for damage. The blade has sharp
edges. When you hold the blade, use
gloves or cloth material to protect your
hands.
If you keep the blade (1) sharp and inspect the
blade for damage, the blade will cut better and
be more safe to operate. Frequently check the
blade for excessive wear, cracks, or other dam-
age. Frequently check the nut (3) that holds the
blade (1). Keep the nut (3) tight. If the blade hits
an object, stop the engine. Disconnect the wire
to the spark plug. See if the blade is bent or
damaged. Check the blade adapter (5) for dam-
age. Before you operate the unit, replace dam -
aged parts with original equipment parts. See
the authorized service centre in your area. Every
three years, have an authorized service person
inspect the blade or replace the old blade with
an original equipment part.
How To Remove And Install The Blade
(Figure 7)
1. Remove the mower housing. See the instruc-
tions on “How To Remove The Mower Hous-
ing”.
2. Use a piece of wood to keep the blade from
rotating.
3. Remove the nut (3) that holds the blade (1).
4. Check the blade (1) and the blade adapter
(5) according to the instructions for “Inspect
Blade”. Replace a badly worn or damaged
blade with an original equipment blade. See
an authorized service centre in your area.
5. Clean the top and bottom of the mower hous-
ing. Remove all the grass and debris.
6. Mount the blade (1) and blade adapter (5)
on the mandrel (6).
7. Mount the blade (1) so that the hi--lift edges
(7) are up. If the blade is upside down, the
blade will not cut correctly and can cause an
accident.
8. Fasten the blade (1) with the original
washers and nut (3). Make sure the outside
rim of the Belleville washer (2) is against
the blade (1).
WARNING: Always keep the nut (3)
tight that holds the blade (1). A
loose nut or blade can cause an
accident.
9. Tighten the nut (3) that holds the blade (1) to
a torque of 30 foot pounds (41,5 Nm).
10.Install the mower housing. See “How To Re-
move The Mower Housing”.
How To Adjust The Blade Rotation
Control
WARNING: To prevent an injury, the
blade rotation control must operate
correctly.
In normal usage, the blade rotation control will
not require an adjustment. However, if the cut-
GB
11
1740475
ting performance decreases or the quality of cut
is poor, make the following changes.
1. When you mow, make sure the throttle con-
trol in in the FAST position.
2. (Figure 8) Move the blade rotation control to
the DISENGAGE position (1).
3. Stop the engine. Disconnect the wire from
the spark plug.
4. Check the blade(s). Keep a sharp edge on
the blade(s). A blade that is not sharp will
cause the tips of the grass to become brown.
5. (Figure 9) Disconnect the blade drive
spring (2) from the blade control rod (1).
Move the blade drive spring (2) to the
middle hole (4). This will increase the tension
on the mower drive belt.
6. Attach the wire to the spark plug. Mow for a
short distance and again check the quality of
cut. If necessary, m ove the blade drive
spring (2) to the bottom hole (5)
7. Again check the quality of cut. If the quality of
cut has not improved, replace the mower
drive belt. See “How To Replace The Mower
Drive Belt”. If the replacing the belt does not
correct the problem, take the unit to an auth-
orized service centre.
8. Move the blade rotation control to the DIS-
ENGAGE position. Stop the engine.
9. (Figure 10) Check the operation of the blade
brake. Rotate the pulleys with your hand.
Make sure the brake pads (7) are pressed
tightly against the pulleys
WARNING: If the brake pads (7) do
not press tightly against the
pulleys, take the unit to an author-
ized service centre.
10.(Figure 8) Move the blade rotation control to
the ENGAGE position (2).
11. (Figure 10) Check the pads for the blade
brake (7). If the pads are excessively worn
or damaged, replace the brake pad assem-
blies. Correct replacement parts and assist-
ance are available from an authorized
service centre.
12.Attach the wire to the spark plug. Mow for a
short distance and again check the operation
of the blade rotation control.
13.When you move the blade rotation control to
the DISENGAGE position, all movement will
stop within five seconds. If there is move-
ment of the belt or the blades continue to ro -
tate, engage and disengage the blade
rotation control five times to remove any ex-
cess rubber from a new mower drive belt. If
you need assistance, take the unit to an
authorized service centre.
14.(Figure 9) If you replace the mower drive
belt, move the blade drive spring (2) to the
top hole (3).
How To Adjust The Shift Lever (Figure
18)
If the NEUTRAL position on the shift lever does
not match neutral on the gearbox, adjust the
shift lever as follows.
1. Stop the engine.
2. Disconnect the adjuster nut (2) from the
shifter bracket (3).
3. Make sure the shift lever is in the NEUTRAL
position.
4. Push the unit forward. Make sure the gear-
box is in neutral.
5. To align the adjuster nut (2) with the hole in
the shifter bracket (3), turn the adjuster nut
(2).
6. Connect the adjuster nut (2) to the shifter
bracket (3).
7. Make sure the NEUTRAL position on the
shift lever matches neutral on the gearbox.
How To Check And Adjust The Clutch
(Figure 11)
If the motion drive belt is loose, the clutch will
slip when; going up a hill, pulling a heavy load,
or the unit will not move forward. Adjust the
clutch as follows.
WARNING: Before you make an in-
spection, adjustment, or repair to
the unit, disconnect the wire to the
spark plug. Remove the wire from the
spark plug to prevent the engine from
starting by accident.
1. Check the routing of the motion drive belt.
Make sure the belt is installed correctly and
is inside all the belt guides.
2. Remove the cotter pin (1), washer (2), and
brake spring (3) from the adjustable nut
(4).
3. Disconnect the adjustable nut (4) from the
brake lever assembly (5) and the parking
brake latch (6).
4. Align the hole in the brake lever (5) with the
hole in the frame. Hold the brake lever (5) in
placewitha6mmpin or bolt (7).
5. Pull the clutch rod forward until tight. Turn the
adjustable nut (4) until the nut will fit through
theholeinthebrake lever (5).
6. Assemble the adjustable nut (4) to the
parking brake latch (6), brake lever (5) and
brake spring (3).Fastenwiththewasher (2)
and cotter pin (1).
7. Removethe6mmpin or bolt (7).
8. If the belt still slips after the clutch has been
adjusted, then the motion drive belt is worn
or damaged and must be replaced. See
“How To Replace The Motion Drive Belt”.
How To Check And Adjust The Drive
Brake (Figure 12)
Completely push the clutch/brake pedal forward.
Set the parking brake. Move the shift lever to the
neutral (N) position. Push the unit. If the rear
wheels rotate, adjust or replace the brake pads.
Adjust the drive brake (1) as follows.
1. The location of the drive brake (1) is on the
right side of the gearbox (3).
2. Make sure the parking brake is set and the
shift lever is in neutral (N). Turn the hex nut
(2) in a clockwise direction until the rear
wheels do not turn when the unit is pushed
forward.
3. Release the parking brake and push the unit.
If the unit does not roll, turn the hex nut (2)
in a counter--clockwise direction until the unit
rolls.
4. Set the parking brake. Push the unit. If the
rear wheels do not turn, the drive brake (1)
is correctly adjusted. Release the parking
brake.
WARNING: If you cannot correctly
adjust the drive brake, replace the
brake pads. Correct replacement
parts and assistance are available from an
authorized service centre.
How To Remove The Battery (Figure 4)
To charge or clean the battery (1), remove the
battery (1) from the unit as follows.
WARNING: To prevent sparks, dis-
connect the black battery cable (8)
from the negative (--) terminal be-
fore you disconnect the red cable (5).
WARNING: The battery contains
sulphuric acid which is harmful to
the skin, eyes and clothing. If the
acid gets on the body or clothing, wash
with water.
1. Disconnect the black cable (8) from the
negative (--) terminal.
2. Disconnect the red cable (5) from the posi-
tive (+) terminal (4).
3. Lift the battery tray (3) and the battery (1)
out of the unit.
How To Charge The Battery (Figure 4)
WARNING: When you charge the
battery, do not smoke. Keep the
battery away from any sparks. The
fumes from the battery acid can cause an
explosion.
1. Before you charge the battery (1), remove
the battery (1).
2. To charge the battery (1),usea12voltbat-
tery charger. Charge at a rate of 6 amperes
for 1 hour.
3. Install the battery (1).
WARNING: To prevent sparks,
fasten the red cable to the positive
(+) terminal before you connect the
black cable.
4. Fasten the red cable (5) to the positive (+)
terminal (4) with the fasteners as shown.
5. Fasten the black cable (8) to the negative
(--) terminal with the fasteners as shown.
How To Level The Mower Housing
(Figure 13 and Figure 14)
If the mower housing is level, the blade will cut
easier and the lawn will look better.
WARNING: Before you make an in-
spection, adjustment, or repair to
the unit, disconnect the wire to the
spark plug. Remove the spark plug wire to
prevent the engine from starting by acci-
dent
1. Make sure the unit is on a hard flat surface.
2. Check the air pressure in the tyres. If the air
pressure is incorrect, the mower housing will
not cut level. Make sure the tyres are inflated
to: Front Tyres 0,97 BAR (14 PSI), Rear
Tyres 0,69 BAR (10 PSI).
3. (Figure 13) Move the lift lever (1) to the
lowest cut position (2).
GB
12
1740475
WARNING: The lifter lever (3) is
spring loaded. Make sure the lift
lever (3) is locked in the lowest cut
position (2).
4. (Figure 14) Loosen the left and right ad-
juster knobs (1). Push down on each side of
the mower housing. Make sure both sides of
the mower housing are setting on a flat sur-
face. Also, make sure the lift links are loose
and can easily move up or down.
5. Push down on the lift links (2) and tighten
the left and right adjuster knobs (1).Make
sure the adjuster knobs (1) are tight. If
necessary, use a wrench to tighten the ad-
juster knobs (1).
6. (Figure 13) Raise the lift lever (1).
7. Mow for a short distance. If the height of cut
is not level, repeat the above steps.
Where To Lubricate (Figure 15)
Lubricate the areas shown
with engine oil.
Apply grease with a brush to
the areas shown.
Models with grease fittings:
Lubricate with grease gun.
NOTE: Apply grease to the steering gear as-
sembly.
CAUTION: If the unit is operated in dry areas
that have sand, use a dry graphite spray to
lubricate the unit.
Check The Tyres
Check the air pressure in the tyres. Tyres with
too much air pressure will cause the unit to ride
rough. Also, the wrong air pressure will keep the
mower housing from cutting level. The correct
air pressure is: Front Tyres 0,97 BAR (14 PSI),
Rear Tyres 0,69 BAR (10 PSI).
How To Replace The Motion Drive Belt
1. Remove the mower housing. See the instruc-
tions on “How To Remove The Mower Hous-
ing”.
2. Completely push the pedal forward and en-
gage the parking brake.
3. (Figure 16) Remove the idler pulley (1).
4. (Figure 17) To access the belt guides (1),
remove the battery and battery tray. See
“How To Remove The Battery”.
5. Loosen the belt guides (1) at the drive
pulley (2).
6. (Figure 16) Remove the motion drive belt
(3) from the drive pulley (4).
7. (Figure 18) Remove the adjuster nut (2)
from the shifter bracket (3). Pull the motion
drive belt over the shifter bracket (3).
8. (Figure 19) To remove the motion drive belt
(1) from the stack pulley (2), pull the front
end of the belt under the stack pulley (2)
and then back between the stack pulley and
the steering plate (3).
9. (Figure 20) Remove the access panel (1).
10.Remove the two screws (4) that attach the
steering shaft assembly (2). Raise the
steering wheel and steering shaft assembly
(2). Pull the motion drive belt (3) under the
steering shaft assembly (2).
11. Remove the motion drive belt. A correct re-
placement part or assistance is available
from an Authorized Service Centre in your
area.
12.To install the motion drive belt, reverse the
above steps.
13.(Figure 21) Check the routing of the motion
drive belt (1). Make sure the motion drive
belt is installed correctly on the idler pulley
(2). Make sure the steering shaft assembly
(3) is inside the motion drive belt (1).
How To Replace The Mower Drive Belt
(Figure 10)
1. Remove the mower housing. See the instruc-
tions on “How To Remove The Mower Hous-
ing”.
2. Pull the belt retainer (1) away from the idler
pulley (2) and remove the mower drive belt
(3).
3. Pull the belt retainer (4) away from the right
mandrel pulley (5) and remove the mower
drive belt (3).
4. Pull the belt retainer (4) away from the left
mandrel pulley (6) and remove the mower
drive belt (3). A correct replacement part or
assistance is available from an Authorized
Service Centre in your area.
5. To install the mower drive belt, reverse the
above steps.
How To Remove The Mower Housing
(Figure 22)
1. Move the blade rotation control (1) to the
DISENGAGE position.
2. Move the lift lever (2) to the level adjust-
ment position.
3. Remove the hair pins and the washers from
the adjuster arms (3). See illustrations “C”
and “D”.
4. Remove the hair pins and washers from the
suspension links (4). See illustrations “A”
and “B”.
5. Disconnect the extension spring (5) from
the blade control rod (6). See illustration
“E”.
6. Disconnect the front hanger (9) from the
axle support. See illustration “F”.
7. Remove the mower drive belt (7) from the
stack pulley (8).
8. Pull the mower housing away from the right
side of the unit.
9. To install the mower housing, reverse the
above steps.
How To Replace The Fuse
If the fuse is blown, the engine will not start.
Remove the fuse and replace with a 15 amp.
automotive fuse.
Storage (over 30 days)
At the end of each year, prepare the unit for stor-
age as follows.
1. Drain the fuel from the carburettor and the
fuel tank. Change the engine oil. See the en-
gine manufacturer’s instructions.
2. Clean the entyre unit.
3. Charge the battery.
How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a sep-
arate Parts List Book.
Use only manufacturer’s authorized or approved
replacement parts. Do not use attachments or
accessories not specifically recommended for
this unit. In order to obtain proper replacement
parts you must supply the model number of your
mower (see nameplate).
Replacement parts, except for the engine, trans-
mission, transaxle or differential, are available
from the store where the mower was purchased
or a service shop recommended by the store.
W arranty service is available only through Autho-
rized Service Dealers. Locate your nearest dealer
in our locator map at www.murray.com.
Replacement parts for the engine, transaxle, or
transmission, are available from the manufac-
turer’s authorized service centre found in the
commercial pages of the telephone directory.
Also, see the individual engine or transmission
warranties to order replacement parts.
When ordering the following information is re-
quired:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
GB
13
1740475
TROUBLE SHOOTING CHART
PROBLEM: The engine will not start.
1. Follow the steps, “How To Start The Engine”
in this book.
2. Electric--Start Models: Clean the battery ter-
minals. Tighten the cables.
3. Check for a loose wire. Tighten the limit
switches. (See the wiring diagram.)
4. Drain the fuel tank. Clean the fuel line. Re-
place the fuel filter.
5. Remove the spark plug(s). Move the throttle
to the SLOW position. Turn the ignition key to
the ON position. Try to start the engine sev-
eral times. Install the spark plug.
6. Replace the spark plug.
7. Adjust the carburettor.
PROBLEM: The engine will not turn
over.
1. Follow the steps, “How To Start The Engine”
in this book.
2. Electric--Start Models: Charge the battery.
3. Replace the fuse.
4. Check the wiring harness for damage or a
loose connection. Repair the damaged wire.
5. Electric--Start Models: replace the solenoid.
Recoil--Start Models: replace the module.
PROBLEM: The engine is difficult to
start.
1. Adjust the carburettor.
2. Replace the spark plug.
3. Replace the fuel filter.
PROBLEM: The engine does not run
smooth or has a loss of power.
1. Check the oil.
2. Clean the air filter.
3. Clean the air screen.
4. Replace the spark plug.
5. The engine is working too hard. Use a lower
gear.
6. Adjust the carburettor.
7. Replace the fuel filter.
PROBLEM: The engine does not run
smooth at fast speed.
1. Replace the spark plug.
2. Adjust the throttle control.
3. Clean the air filter.
4. Replace the fuel filter.
PROBLEM: The engine stops when the
blades are engaged.
1. Check the wiring harness for damage or a
loose connection. Repair the damaged wire.
2. Grass bag must be installed (applies only to
model with rear discharge grass bag).
PROBLEM: On slopes, the engine
stops.
1. Mow up and down s lopes. Never mow
across a slope.
PROBLEM: The engine will not idle.
1. Replace the spark plug.
2. Clean the air filter.
3. Adjust the carburettor.
4. Adjust the throttle control.
5. Drain the fuel tank. Clean the fuel line. Re-
place the fuel filter.
PROBLEM: A hot engine causes a de-
crease in power.
1. Clean the air screen.
2. Check the oil.
3. Adjust the carburettor.
4. Replace the fuel filter.
PROBLEM: Excessive vibration.
1. Replace the blade.
2. Check for loose engine bolts.
3. Decrease the air pressure in the tyres.
4. Adjust the carburettor.
5. Check for a damaged belt or damaged
pulley. Replace the damaged parts.
PROBLEM: The grass does not dis-
charge correctly.
1. Stop the engine. Clean the mower housing.
2. Raise the height of cut.
3. Replace or sharpen the blade(s).
4. Move the s hift lever to a slower speed.
5. Move the throttle control to the FAST posi-
tion.
6. Replace the spring for the blade idler.
7. Clean the extension tube and the connector
tube (applies only to model with rear dis-
charge grass bag).
PROBLEM: The mower housing does
not cut level.
1. Check the air pressure in the tyres.
2. Adjust the l evel of the mower housing.
3. Check the front axle. If the front axle does
not freely pivot, loosen the axle bolt(s).
PROBLEM: The mower blades will not
rotate.
1. Check the mower drive belt. Make sure the
belt is installed correctly.
2. Replace the mower drive belt.
PROBLEM: The unit will not move when
the clutch is engaged.
1. Check the motion drive belt. Make sure the
belt is installed correctly.
2. Adjust the clutch.
3. Replace the motion drive belt.
PROBLEM: The unit moves slower or
stops when the clutch is engaged.
1. Adjust the clutch.
2. Replace the motion drive belt.
PROBLEM: When the clutch/brake
pedal is released, belt noise can be
heard.
1. Temporary belt noise does not change the
operation of the unit. If belt noise is continu-
ous, check the routing of the belt. Make sure
the belt is inside all belt guides.
2. If the noise is continuous, adjust the clutch.
PROBLEM: The rear wheels spin over
uneven terrain.
1. Check the front axle. If the front axle does
not freely pivot, loosen the axle bolt(s).
PROBLEM: The transaxle is difficult to
shift between gears with the engine run-
ning and the clutch depressed.
1. Check the clutch adjustment to make sure
the belt stops when the clutch pedal is de-
pressed with the transaxle in (N) neutral.
2. Check the belt guides around the transaxle
drive pulley. Make sure the belt guides do not
touch the pulley.
F
14
1740475
TABLE DES MATIERES
PICTOGRAMMES INTERNATIONAUX 14
INFORMATIONS GENERALES 15
POUR UNE UTILISATION EN TOUTE SECURITE 15
MONTAGE 16
FONCTIONNEMENT 17
TABLEAU D’ENTRETIEN 19
ENTRETIEN 19
TABLE DE DEPANNAGES 23
PICTOGRAMMES INTERNATIONAUX
REMARQUE IMPORTANTE: les pictogram-
mes suivants sont situés sur votre appareil
ou dans la documentation ci-jointe. Avant de
vous servir de la tondeuse, apprenez à re-
connaître chaque pictogramme.
REMARQUE: les illustrations et
pictogrammes commencent en page 2.
Pictogrammes d’avertissement (Figure 23)
1 Avertissement
2 REMARQUE IMPORTANTE : lire le manuel
de l’utilisateur avant de mettre la tondeuse
en marche.
3 AVERTISSEMENT : projection d’objets. Gar-
dez vos distances. Lire le manuel de l’utilisa-
teur avant de mettre la tondeuse en marche.
4 AVERTISSEMENT : ne pas utiliser la ton-
deuse sur des pentes de plus de 10 degrés.
5 DANGER: rester à l’écart, s urtout les en-
fants, de l’appareil.
6 DANGER: ne pas poser le pied.
7 DANGER: gardez vos pieds et mains à dis-
tance de la lame rotative.
8 Niveaux de puissance sonore de 100
dB(A) déclarés conformes à ceux définis
par la directive européenne 2000/14/CE.
9 DANGER: débrancher le câble de la bougie
avant toute inspection de l’appareil.
10 AVERTISSEMENT : surface brûlante.
11 AVERTISSEMENT : prêter attention lors du
branchement et débranchement des acces-
soires.
12 AVERTISSEMENT : prendre garde à ne
pas s’écraser les doigts.
13 IMPORTANT : pour régler le niveau du car-
ter du bloc de coupe, suivre attentivement
les instructions indiquées dans le Guide de
l’utilisateur.
14 AVERTISSEMENT : ne pas s’approcher de
la lame tant que le moteur tourne.
Pictogrammes de commande et de
fonctionnement (Figure 24)
1 Démarrage du moteur
2 Phares
3 Moteur en marche
4 Arrêt du moteur
5 Moteur en marche
6 Frein
7 Frein de stationnement
8 Embrayage
9 Ralenti
10 Rapide
11 Starter
12 Huile
13 Commande de rotation de la lame
14 Soulever
15 Essence
MODEL NO.: 405013X50C
SERIAL NO.:
2850 RPM
172 kg
SKU No.:
YYYY MM DD:
www.briggsandstratton.com
Niveaux de puissance sonore de 100 dB(A) déclarés conformes à ceux définis
par la directive européenne 2000/14/CE.
Niveau de pression acoustique à la station de l’utilisateur 83
dB.
Résultats à l’oreille obtenus en application de la norme EN 836/A2:2001.
Net kW 6.39
Niveaux de vibration déclarés conformes à ceux définis par la directive
européenne 98/37/CE.
Niveaux de vibration relevés conformément à la norme BS EN 1032 :
Siège 2
m/s
2
, Marchepied droit 2,9 m/s
2
, Marchepied gauche 3,3 m/s
2
Niveaux de vibration relevés conformément à la norme BS EN 1033:
Volant 3,5
m/s
2
Valeurs déterminées en station immobile sur une surface cimentée à un régime de
2850 t.p.m..
Assembled in Lawrenceburg, TN 38464; USA
by Swisher, Inc. for Briggs & Stratton Corporation
F
15
1740475
INFORMATIONS GENERALES
Maîtrisez le produit : si vous connaissez l e
produit et comprenez comment celui-ci fonction -
ne, vous en obtiendrez les meilleurs résultats.
Au fur et à mesure que vous lisez le manuel,
consultez les illustrations ci -jointes. Sachez re-
connaître l’emplacement et la fonction de cha-
que commande. Afin de prévenir tout accident,
suivez les instructions d’utilisation ainsi que les
règles de sécurité. Conservez ce manuel car i l
peut vous être utile dans le futur.
AVERTISSEMENT : ce symbole vous indi-
quera les mesures de sécurité à prendre.
Le message de ce symbole est le suivant :
“Attention! Soyez prudent! Votre sécurité
est en jeu.”
Responsabilité de l’utilisateur
AVERTISSEMENT : il se peut que
cette tondeuse éjecte des objets
sur son passage. Sachez aussi que
cette machine pourrait vous amputer les
mains et les pieds. Si vous n’observez pas
les mesures de sécurité suivantes, vous
encourez le risque de vous blesser (ainsi
que les gens à proximité) sérieusement,
voire mortellement.
Un utilisateur responsable doit suivre
les instructions ci-dessous.
POUR UNE UTILISATION EN
TOUTE SECURITE
Modèles de tondeusesà lames rotatives
Conseils préliminaires
1. Lisez les instructions très attentivement.
Familiarisez-vous avec les commandes et
l’utilisation appropriée de l’équipement.
2. Ne jamais laisser des enfants ou des per-
sonnes non familiarisées avec le produit utili-
ser la tondeuse. Des régulations
gouvernementales peuvent établir un âge
minimum.
3. Ne jamais tondre lorsque des personnes,
surtout des enfants, ou des animaux sont à
proximité.
4. Garder à l’esprit que l’opérateur ou l’utilisa-
teur est tenu responsable des risques ou
accidents arrivés aux autres personnes ou
à leurs biens.
5. Ne pas prendre de passagers.
6. Tous les conducteurs devraient recevoir
des conseils théoriques et pratiques. Ces
conseils sont :
a. la nécessité d’être soigneux et attentif
lors de la tonte sur tondeuse autoportée
b. la reprise de contrôle de la tondeuse
en pente est impossible par les freins.
La perte de contrôle s’explique de la
manière suivante :
prise de la roue insuffisante;
conduite trop rapide;
freinage inadéquat
le type de machine ne convenant
pas à la tâche;
manque d’attention sur les
conséquences de tontes en pen-
te, en particulier;
mauvais accrochage ou répartition
inégale de l’herbe dans le sac.
Préparation
1. Lors de la tonte, portez toujours des chaus-
sures qui vous apportent une protection
complète et des pantalons. Ne jamais tondre
pieds nus ou avec des sandales ouvertes.
2. Inspectez la zone à tondre et enlevez tous
les objets que la machine pourrait éjecter
sur son passage.
3. AVERTISSEMENT -- L’essence est haute-
ment inflammable.
a. Réserver du carburant dans des jerri-
canes prévues à cet effet.
b. Remplir de carburant uniquement à
l’air libre et ne pas fumer.
c. Ajouter du carburant avant de démar-
rer votre tondeuse autoportée. Ne ja-
mais enlever la protection du réservoir
ni même ajouter de carburant lorsque
le moteur est en m arche ou c haud.
d. Si une fuite d’essence se produit, ne
pas tenter de démarrer la machine et
l’éloigner de la zone de fuite en ques-
tion : attendez que les vapeurs d’es-
sence se soient dissipées avant
d’utiliser la tondeuse.
e. Replacer correctement les bouchons
du réservoir et de la jerricane.
4. Changer les amortisseurs de bruit défec-
tueux.
5. Avant toute utilisation, s’assurer que les
lames, boulons de lames et positionnement
des lames ne soient pas usés ou endom-
magés. Remplacer les lames et boulons
usés ou endommagés en même temps afin
de respecter l’équilibre.
6. En ce qui concerne les tondeuses multi l a-
mes, prendre garde lors de la rotation
d’une lame car celle-ci peut entraîner la ro-
tation des autres.
Utilisation
1. Ne pas utiliser mettre le moteur en route
dans un espace confiné de dangereu-
ses vapeurs de monoxyde de carbone peu-
vent s’accumuler.
2. Tondre seulement durant la journée ou bien
sous un éclairage artificiel puissant.
3. Avant de démarrer la tondeuse autoportée,
désengager toutes les manettes de c om-
mande de lames et se mettre au point mort.
4. Ne pas tondre sur une pente de plus de 10
degrés.
5. Garder à l’esprit que toute pente peut être
dangereuse. Le déplacement demande
une attention redoublée. Afin de prévenir
toute chute :
a. ne pas s’arrêter ou démarrer soudai-
nement lorsqu’on se trouve en pente
ascendante ou descendante;
b. enclencher l’embrayage lentement, en
veillant à ce que les vitesses de la ton-
deuse soient toujours engagées, sur-
tout lors des déplacements en
descente;
c. la vitesse devrait être réduite dans les
pentes et dans les virages serrés;
d. prêter attention aux bosses, aux creux
et autres dangers occultés;
e. ne jamais tondre en diagonal de la
pente, sauf si la tondeuse est conçue
à cet effet.
6. Soyez attentif lorsque vous tirez du maté-
riel ou tout autre équipement lourd.
a. Utiliser seulement des barres de trac-
tion approuvées.
b. Limitez les chargements à ceux que
vous pouvez contrôler sans aucun
risque.
c. Ne pas faire de virages secs. Tourner
avec précaution.
d. Utiliser des contrepoids ou des lests
de roues comme suggéré dans le ma-
nuel de l’utilisateur.
7. Prenez garde au trafic lorsque vous devez
traverser la chaussée ou lorsque vous en
êtes prêt.
8. Arrêtez la rotation des lames avant de tra-
verser une zone non recouverte de pelouse.
9. Lors de l’utilisation d’attaches, ne jamais
diriger la décharge de matériel vers les per-
sonnes à proximité et n’autoriser personne
à s’approcher de la tondeuse en marche.
10. Ne jamais faire marcher la tondeuse avec
des éléments de protection défectueux, ou
sans aucun dispositif de sécurité
11. Ne pas changer les réglages du régulateur
du moteur ni échauffer le moteur. L’utilisa-
tion de la tondeuse à vitesse excessive
peut accroître le risque de blessure.
12. Avant de quitter l’appareil :
a. désengager l’alimentation et rabaisser
le bloc accessoire ;
b. se positionner au point mort et en frein
de stationnement ;
c. couper le moteur et enlever la clé.
13. Désengager la courroie du bloc accessoire,
arrêter le moteur, et débrancher le(s) -
ble(s) de la bougie ou enlever la clé de
contact ;
a. avant de débloquer et nettoyer la ma-
chine de toute obstruction ;
b. avant d’inspecter, nettoyer, ou travail-
ler sur la tondeuse ;
c. après avoir touché un objet. Inspecter
la tondeuse et effectuer les répara-
tions nécessaires avant de redémarrer
la machine ;
d. si la machine commence à vibrer de
façon anormale (vérifier dans l’instant).
14. Désengager la courroie du bloc accessoire
lors de son transport ou lorsqu’elle n’est
pas utilisée.
15. Couper le moteur et désengager la courroie
du bloc accessoire
a. avant de remettre du carburant;
b. avant d’enlever le receveur à herbe;
c. avant de régler la hauteur, à moins que
ce réglage ne puisse se faire assis.
16. Réduire le réglage de l’accélérateur au point
mort et, si la tondeuse est fournie avec une
valve de coupure d’alimentation, couper l’ali-
mentation en carburant après la tonte.
17. Avant et lors du recul, regarder derrière et
dessous afin de s’assurer qu’il n’y a pas
de jeunes enfants autour.
18. Redoubler d’attention à l’approche de coins
aveugles, de buissons, arbres ou autres
objets qui peuvent obstruer la visibilité.
Maintenance et entreposage
1. En ce qui concerne les tondeuses multi l a-
mes, prendre garde lors de la rotation
d’une lame car celle-ci peut entraîner la ro-
tation des autres.
2. Quand la tondeuse doit être mise en sta-
tionnement, rangée ou laissée pour un mo-
ment plus ou moins long, rabaisser les
dispositifs de tonte à moins qu’un verrouil-
lage mécanique ne soit mis en place.
3. S’assurer que les écrous, les boulons et les
vis soient bien serrés pour que la tondeuse
soit dans de bonnes conditions d’utilisation.
4. Ne jamais garder la tondeuse avec du car-
burant dans le réservoir à l’intérieur d’un
bâtiment des émanations peuvent at-
teindre une flamme nue ou une étincelle.
5. Laisser la tondeuse refroidir avant de la
ranger dans une enceinte.
6. Afin de limiter tout risque de feu, s’assurer
que le moteur, l’amortisseur de bruit, le com-
partiment de batterie et la zone de réserve
de carburant soient débarrassés d’herbe, de
feuilles ou de graisse excessive.
7. Vérifier fréquemment que le receveur d’her-
be ne soit pas usé ou détérioré.
8. Remplacer les pièces usées ou défectueu-
ses.
9. Si le réservoir doit être vidé, ceci doit être
fait au dehors.
F
16
1740475
MONTAGE
Toutes les attaches sont dans le sac des pièces
détachées. Ne vous débarrassez d’aucune piè-
ce ni d’aucun matériel jusqu’à ce que l’unité soit
assemblée.
AVERTISSEMENT : avant de pro-
céder au montage ou à l’entretien
de la tondeuse, enlever le câble de
la bougie.
REMARQUE : dans ce manuel de l’utilisateur,
la gauche et la droite décrivent l’emplace -
ment d’une pièce avec l’opérateur assis sur
la tondeuse.
REMARQUE : les illustrations et
pictogrammes commencent en page 2.
REMARQUE: veuillez vous servir des atta-
ches montrées à la Figure 25 pour assembler
les différentes pièces détachées.
Installation des roues avant (Figure 1)
A l’aide d’un couteau, coupez les quatre côtés
de la boîte. Installez les roues avant (1) dans
ce bac.
REMARQUE : soulever l’avant de la tondeuse
à l’aide d’un bâton d’environ 1,25 m (4
pieds). Sinon demander à une autre person-
ne de soulever la tondeuse. Attention, ne pas
laisser tomber la tondeuse!
1. Soulevez l’avant de la tondeuse. Placez un
support (bûche de bois) en dessous.
2. Assurez-vous que la valve (2) soit à l’exté-
rieur de la tondeuse. Faites glisser la roue
avant (1) sur l’axe (3).
3. Fixer chaque roue avant (1) avec une ron-
delle (4) et une goupille fendue (5).Ren-
versez les bords de la goupille fendue (5)
afin de maintenir la roue avant (1) sur l’axe
(3).
4. Une fois les roues avant (1) installées, sou -
levez la tondeuse de son support. Retirez la
tondeuse de la boîte.
5. Si la tondeuse dispose d’enjoliveurs de
moyeu (6), i nstallez-les (6). Assurez-vous
que les rondelles (4) maintiennent les enjo -
liveurs de moyeu (6) en place.
Installation du siège (Figure 2)
1. Enlevez délicatement le sac plastique du siè-
ge (1).
2. Alignez les orifices dans la charnière du siè-
ge (2) aux orifices du siège (1). Attachez le
siège (1) àlacharnière du siège (2) à l’aide
des attaches (4) et (5).
3. Vérifiez la position de fonctionnement du siè-
ge (1). Si le siège (1) a besoin d’être ajusté,
desserrez les boulons à oreilles (5).Faites
glisser le siège (1) en avant et en arrière le
long de la fente de réglage du siège (3).
Resserrez les boulons à oreilles (5).
Montage du volant (Figure 3)
1. Assurez-vous que les roues avant pointent
bien vers l’avant.
2. Faites glisser l e couvercle (3) sur l a colon-
ne de direction (2). Assurez-vous que le
collier du du couvercle (3) soit au dessus.
3. Faites glisser le volant (1) sur la colonne de
direction (2).
4. Fixez le volant (1) àlacolonne de direc-
tion (2) à l’aide de la vis (4) et de la rondelle
(6).
5. Certains modèles disposent d’une étiquette
(7) en option, se trouvant dans le sac des
pièces détachées. Attachez-le (7) au centre
du volant (1).
Entretien de la batterie libre (Figure 4)
REMARQUE IMPORTANTE: avant de relier
les câbles de la batterie à celle-ci, vérifiez sa
date. Cette date indique si la batterie doit
être chargée.
1. Vérifiez le haut de la batterie (1) et repérez
la date.
2. Si la batterie (1) est mise en route avant la
date , ses câbles peuvent être attachés sans
la charger. Cf. “Installation des câbles de bat-
terie”.
3. Si la batterie (1) est mise en route après sa ,
la batterie (1) doit être chargée. Cf. “Charge-
ment de la batterie d’entretien libre”.
Chargement de la batterie (Figure 4)
AVERTISSEMENT : Lors du charge-
ment de la batterie, ne pas fumer.
Eviter d’exposer la batterie à toute
étincelle. Les émanations provenant de
l’électrolyte de batterie peuvent provoquer
une explosion.
1. Enlevez la batterie (1) et son bac (3).
2. Enlevez les capuchons des bornes de la bat-
terie.
3. Utilisez un chargeur de batterie de 12 volts
pour charger la batterie (1). Chargez-la à
un taux de 6 ampères par heure. Si vous ne
disposez pas de chargeur de batterie, des
professionnels peuvent le faire pour vous.
4. Installer la batterie (1) et son bac (3).Sas-
surer que la borne positive (+) (4) est à
gauche.
Installation des câbles de batterie
(Figure 4)
AVERTISSEMENT : afin de prévenir
toute étincelle, attacher le câble rou-
ge à la borne positive (+) avant de
connecter au câble noir.
1. Enlevez les capuchons des bornes de la bat-
terie.
2. Faites glisser l e capuchon de borne (2) sur
le câble rouge (5). Attachez le câble rouge
(5) àlaborne positive (+) (4) à l’aide des
attaches (6) et (7).
3. Attachez le câble noir 8 à la borne négative
(--) à l’aide des attaches (6) et (7).
Inspection des pneus
Vérifiez la pression des pneus. Un excès de
pression peut rendre la conduite cahoteuse. Par
ailleurs, une mauvaise pression des pneus em-
pêchera le bloc de coupe de tondre de façon
égale. La pression convenable est de 0,97 BAR
(14 PSI) pour les roues avant et de 0,69 BAR
(10 PSI) pour les roues arrière. Les pneus ont
été surgonflés pour la livraison.
Vérification du niveau de la tondeuse
Assurez-vous que le niveau de tonte est tou-
jours le même. Après avoir tondu sur une petite
distance, inspectez la zone tondue. Si le bloc de
coupe ne tond pas de manière égale, consulter
les instructions dans “Mise à niveau du bloc de
coupe” dans la section Entretien de ce manuel
de l’utilisateur.
Préparation du moteur
REMARQUE : le moteur quitte l’usine rempli
d’huile. Vérifier le niveau de l’huile. En ajou-
ter autant que nécessaire.
Consultez les instructions données pas le fabri-
cant du moteur pour déterminer l’essence et
l’huile à utiliser. Avant toute utilisation, lisez les
instructions de sécurité, d’utilisation, d’entretien,
et de rangement.
AVERTISSEMENT : suivre les ins-
tructions du fabricant de ce moteur
au sujet de l’utilisation de l’essence
et de l’huile. Se munir toujours d’une jerrica-
ne prévue à cet effet. Ne pas fumer lorsque
l’on verse du carburant dans le moteur. Ver-
ser le carburant à l’air libre, après avoir cou-
le moteur. Laisser le moteur refroidir pen
-
dant un moment.
Remarque importante! Avant d e tondre :
U Vérifiez l’huile du moteur.
U Remplissez le réservoir d’essence.
U Vérifiez la pression des pneus.
U Vérifiez le niveau du bloc de coupe.
U Attachez les câbles de la batterie.
F
17
1740475
FONCTIONNEMENT
REMARQUE : les illustrations et pictogram-
mes commencent en page 2.
Emplacement des commandes (Figure 5)
Manette de commande de rotation de la lame
(1) : elle sert à démarrer et à arrêter la rotation
de la lame.
Pédale d’embrayage/freinage (2) : la pédale a
deux fonctions. La première, d’embrayer ; la
deuxième, de freiner.
Contact de phare (3) : c’est la première partie
du contact de démarrage. Pour tondre avec le
phare, tourner la clé vers la position du phare.
Contact de démarrage (3) : il sert à démarrer
et à arrêter le moteur.
Levier de vitesses (4) : il sert à changer les
vitesses de la tondeuse.
Levier de hauteur de coupe (5) : il sert à ajus-
ter la hauteur de la tonte.
Manette de frein de stationnement (6) : elle
permet d’engager la tondeuse lorsque l’on ne
s’en sert plus.
Manette de contrôle des gaz (7) : elle sert à
augmenter ou réduire la vitesse du moteur.
Bloc accessoire
Cette tondeuse peut en disposer de plusieurs.
Cette tondeuse peut tirer des accessoires tels un
nettoyeur de pelouse, un aérateur de pelouse, ou
un épandeur à trémie. Mais cette tondeuse ne
peut tirer des engins comme des charrues, des
pulvérisateurs à disque ou des bineuses.
On peut se servir d’accessoires tractés ou de
remorques tant que le poids ne dépasse pas 113
kg.
Utilisation d e la manette de contrôle
des gaz (Figure 5)
Elle permet d’augmenter ou réduire la vitesse du
moteur (7) .
1. La position FAST (rapide) est marquée d’un
cran de positionnement. En utilisation norma-
le ou avec un bac à herbe, positionner la ma-
nette sur FAST. Cette position permet un
chargement maximum de la batterie et un
meilleur refroidissement du moteur.
2. Le régulateur du moteur est réglé à l’usine
afin de garantir les meilleures performances.
Ne pas régler le régulateur dans le but d’aug -
menter la vitesse du moteur.
Utilisation de la manette de commande
de rotation de la lame (Figure 5)
Elle sert à engager la (les) lame(s) (1) .
1. Avant de mettre le moteur, s’assurer que la
manette de commande de rotation de la
lame (1) soit dans la position DESENGAGE.
2. La placer dans la position (1) ENGAGE afin
de permettre la rotation de la (des) lame(s).
REMARQUE : si le moteur s’arrête lors-
que vous engagez la (les) lame(s), le
contacteur du siège n’est pas activé. Bien
s’asseoir au milieu du s iège.
3. Placer la manette de commande de rota-
tion de lame (1) en position DESENGAGE
afin d’arrêter l a (les) lame (s). Avant de quit-
ter l’appareil, veiller à ce que la (les) lame (s)
soit (soient) arrêtée(s).
4. Avant de traverser un trottoir ou une route
avec la tondeuse, veiller à ce que la manette
de commande de rotation de la lame soit en
position DESENGAGE (1).
AVERTISSEMENT : veiller à ce que
vos mains ou pieds se tiennent à
l’écart de la lame, de l’ouverture du
déflecteur, et du bloc de coupe lorsque le
moteur est en marche.
Utilisation du levier de vitesses (Figure 5)
Pour changer les vitesses de la tondeuse, suivre
les étapes suivantes :
ATTENTION : avant de se servir du levier de
vitesses, appuyer complètement sur la péda-
le d’embrayage/freinage afin d’arrêter la ton-
deuse. Si la tondeuse n’est pas à l’arrêt, la
boîte de vitesses pourrait être endommagée.
1. Appuyer complètement sur la pédale d’em-
brayage/freinage afin d’arrêter la tondeuse.
Garder le pied sur l a pédale.
2. Placer la manette de contrôle des gaz (7)
en position SLOW (ralenti).
3. Pour se déplacer vers l’avant, placer le le-
vier de vitesses (4) à un réglage de vitesse
en avant. Pour se déplacer vers l’arrière, pla-
cer le levier de vitesses (4) en position
contraire.
4. Relâcher lentement la pédale d’embrayage/
freinage (2). Ne pas garder le pied sur la
pédale.
5. Placer la manette des gaz (7) en position
FAST (rapide).
Utilisation du frein de stationnement
(Figure 5)
1. Appuyer complètement sur la pédale d’em-
brayage/freinage (2).
2. Soulever la manette de frein de stationne-
ment (6).
3. Retirerlepieddelapédale d’embrayage/
freinage (2) puis relâcher la manette de
frein de stationnement (6). S’assurer que le
frein de stationnement retienne la tondeuse.
4. Pour relâcher le frein de stationnement (6),
appuyer complètement sur la pédale d’em-
brayage/freinage (2) en avant. Le frein de
stationnement sera relâché automatiquement.
AVERTISSEMENT : avant de des-
cendre de la tondeuse, déplacer le
levier de vitesses vers le point mort
(N). Actionner le frein de stationnement.
Mettre la commande de rotation de la lame
en position DESENGAGE. Couper le mo-
teur et enlever la clé de contact.
AJUSTEMENT DE LA HAUTEUR DE
COUPE (Figure 5)
Pour l’ajuster, réduire ou augmenter le levier de
hauteur de coupe (5) comme indiqué :
1. Déplacer le levier de hauteur de coupe (5)
vers l’avant pour abaisser le bloc de coupe et
le remonter pour élever le bloc de coupe.
2. Lors d’un déplacement sur un trottoir ou rou-
te, déplacer le levier de hauteur de coupe
(5) vers la position la plus haute ainsi que la
commande de rotation de la lame en posi-
tion DESENGAGE.
ARRET DE LA TONDEUSE (Figure 5)
1. Appuyer complètement sur la pédale d’em-
brayage/freinage (2) afin d’arrêter la ton-
deuse. Garder le pied sur la pédale.
2. Déplacer la commande de rotation de la
lame en position DESENGAGE.
3. Déplacer le levier de vitesses (5) vers le
point mort (NEUTRAL).
4. Mettre le frein de stationnement (7).
AVERTISSEMENT : veiller à ce que
le frein de stationnement retienne
la tondeuse.
5. Déplacer la manette de contrôle des gaz
(8) vers la position SLOW.
6. Pour couper le moteur, arrêter l a clé de
contact (4) (position OFF) et la retirer.
Transport de la tondeuse
Pour transporter l a tondeuse, suivre les étapes
suivantes :
1. Mettre la commande de rotation de la lame
en position DESENGAGE.
2. Monter le levier de hauteur de coupe à la po-
sition la plus haute.
3. Régler la manette de contrôle des gaz entre
les positions SLOW et FAST.
4. Pour aller plus vite, augmenter la vitesse par
le levier de vitesses.
Utilisation du bloc de coupe
REMARQUE IMPORTANTE : lors de l’utilisa-
tion du bloc de coupe, avoir toujours la ma-
nette de contrôle des gaz en position FAST.
1. Mettre les moteurs.
2. Régler le levier de hauteur de coupe à la
hauteur désirée. Lorsque l’herbe est haute
ou épaisse, opter pour la position la plus
haute dans un premier temps, puis abaisser
le bloc pour une deuxième tonte.
3. Placer le contrôle des gaz en position SLOW.
4. Mettre lentement la commande de rotation
de lame en position ENGAGE.
5. Appuyer complètement sur la pédale d’em-
brayage/freinage (2) afin d’arrêter la ton-
deuse.
6. Placer le levier de vitesses sur l’un des régla-
ges de vitesse.
REMARQUE : lorsque l’herbe est épaisse
ou lorsque vous tondez avec un bac à
herbe, réglez le levier de vitesses à la vi-
tesse la plus réduite.
7. Relâcher lentement la pédale d’embrayage/
freinage.
8. Placer la commande des gaz en position
FAST. Si vous désirez augmenter ou réduire
la vitesse, arrêter la tondeuse et choisir un
autre réglage de vitesse par le levier de vi-
tesses.
F
18
1740475
9. S’assurer que le niveau de coupe reste cor-
rect. Après avoir tondu sur une petite zone,
l’inspecter. Si le bloc de coupe ne tond pas
de manière égale, consulter les instructions
présentes dans “Mise à niveau du bloc de
coupe” dans la section Entretien.
AVERTISSEMENT : afin de réduire
les risques d’accident, veiller à ne
pas aller trop vite.
Utilisation en pentes
AVERTISSEMENT : ne pas se -
placer (vers le haut ou le bas) dans
des pentes trop raides pour per-
mettre de reculer. Ne jamais se déplacer
en diagonal.
1. Avant de se déplacer en pente ascendante
ou descendante, réduire la vitesse au mini-
mum par le levier de vitesses.
2. Ne pas s’arrêter ou changer les réglages de
vitesse en pente. Si vous devez vous arrêter,
enclencher la pédale d’embrayage/freinage
vers l’avant et le frein de stationnement.
3. Pour redémarrer, veiller à ce que la vitesse
du levier de vitesses soit la plus réduite. Pla-
cer la manette de contrôle des gaz à la posi-
tion SLOW. Relâcher lentement la pédale.
4. Si vous devez vous arrêter ou démarrer en
pente, aménagez-vous de l’espace suffisant
pour que la tondeuse puisse rouler lorsque
vous relâchez le frein et l’embrayage.
5. Redoubler d’attention lorsque vous changez
de directions en pente. Lorsque vous êtes en
pente descendante dans un virage, déplacer
la commande des gaz vers la position SLOW
afin de prévenir tout accident.
AVANT DE DEMARRER LE MOTEUR
Vérification de l’huile
REMARQUE : le moteur a quitté l’usine rempli
d’huile. Vérifier le niveau d’huile. En ajouter
autant que nécessaire. Suivre les instructions
du fabricant de ce moteur au sujet de l’utilisa-
tion de l’essence et de l’huile.
1. Veiller à ce que la tondeuse soit à niveau.
REMARQUE : Ne pas inspecter le niveau
d’huile lorsque la tondeuse est en marche.
2. Vérifier l’huile. Suivre la procédure donnée
dans le manuel du fabricant du moteur.
3. Si nécessaire, ajouter de l’huile jusqu’à at-
teindre la marque FULL (plein) sur la jauge.
La quantité à ajouter depuis ADD (verser)
jusqu’à FULL est montrée sur la jauge. Veil-
ler à ne pas dépasser la marque indiquée.
Ajouter de l’essence
AVERTISSEMENT : Se munir
toujours d’une jerricane prévue à
cet effet. Ne pas fumer lorsque l’on
verse du carburant dans le moteur. Verser
le carburant à l’air libre, après avoir coupé
le moteur. Laisser le moteur refroidir
pendant un moment.
(Figure 6) Remplir le réservoir d’essence (1) à
FULL (2) avec de l’essence ordinaire sans
plomb. Ne pas utiliser de super sans plomb. Ne
pas utiliser d’essence “d’âge” ou sale. L’essence
avec plomb accroît la formation de dépôt et ré-
duit la durée d’utilisation des valves.
Démarrage du moteur
AVERTISSEMENT : le système
électrique dispose d’un mécanisme
de détection de présence (de
l’utilisateur) grâce à un contact de capteur
sur le siège. Ce mécanisme vous signale
si l’utilisateur est assis sur le siège. Le
système arrêtera la tondeuse si l’utilisateur
quitte le siège de celle-ci. Dans votre
intérêt, veiller à ce que le système
fonctionne bien.
REMARQUE : le moteur ne démarrera pas à
moins que l’on ne relâche la pédale d’em-
brayage/freinage et ne place la commande de
rotation de la lame en position DESENGAGE.
1. Appuyer complètement sur la pédale d’em-
brayage/freinage afin d’arrêter la tondeuse.
Garder le pied sur l a pédale.
2. Placer le levier de vitesses au point mort (N).
3. Veiller à ce que la commande de rotation de
la lame soit en position DESENGAGE.
4. Avancer la commande de contrôle des gaz
vers les positions CHOKE (starter) ou FAST
(rapide). Certains modèles disposent d’un
bouton de starter. Le tirer à fond en position
CHOKE.
5. Tourner la clé de contact en position START.
REMARQUE : si le moteur ne démarre pas
après quatre ou cinq essais, placer la
commande de contrôle des gaz en posi-
tion FAST. Réessayer de démarrer. Si vos
essais demeurent infructueux, consulter
la TABLE DE DEPANNAGES.
6. Placer lentement la commande des gaz sur
la position SLOW.
7. Pour démarrer un moteur chaud, placer la
commande des gaz sur une position entre
FAST et SLOW.
Quelques conseils...
1. Pour de meilleurs résultats, il est important
de vérifier le niveau de coupe du bloc de
coupe. Cf. “Mise à niveau du bloc de coupe”
dans la section Entretien.
2. Pour assurer que la coupe soit bien égale de
partout, veiller à ce que les pneus soient
gonflés comme requis.
3. A chaque utilisation, vérifier la lame. Si celle-
ci est recourbée ou défectueuse, la rempla-
cer immédiatement. De même, s’assurer que
l’écrou soit bien serré.
4. Maintenir la (les) lame(s) bien coupante(s).
Des lames usées rendront les bouts des
brins d’herbe marrons.
5. Ne pas couper ni ne mettre en sac l’herbe
mouillée. L’herbe mouillée se tond mal et il
est conseillé d’attendre qu’elle sèche.
6. Utiliser le côté gauche du bloc de coupe pour
couper près d’un objet.
7. Répandre l’herbe coupée sur l a surface ton-
due. Ainsi, l’herbe coupée est répandue de
manière plus égale.
8. Lorsque vous tondez sur une grande surfa-
ce, commencer toujours par la droite pour
que l’herbe rejetée soit éloignée des buis-
sons, des barrières, des allées, etc. Après
deux tours, tondre dans la direction opposée
en tournant à gauche pour finir.
9. Si l’herbe est vraiment haute, procéder à la
tonte en deux fois pour réduire la charge sur
le moteur. D’abord tondre en plaçant le bloc
de coupe dans la position la plus haute, puis
l’abaisser pour le deuxième passage.
10.Pour assurer de meilleures performances du
moteur ainsi qu’une tonte égale de l’herbe,
garder toujours la commande des gaz en po-
sition FAST.
11. Avec un sac à herbe, garder la commande
des gaz en position FAST et le levier de vi-
tesses en première ou deuxième.
12.Pour obtenir une belle pelouse, tondre en
gardant le levier de vitesses aux vitesses les
plus réduites.
13. Après chaque utilisation, nettoyer le fond et le
dessus du bloc de coupe. De même, le garder
propre peut vous aider à prévenir un feu.
F
19
1740475
TABLEAU D’ENTRETIEN
FRÉQUENCE ENTRETIEN OBLIGATOIRE COMMENTAIRES
Chaque jour ou avant utilisation Entretien du moteur. Consulter le Manuel du propriétaire du
moteur.
Vérification des lame(s). Repérer toute fêlure, usure, et pièce trop
endommagée.
Retirer tout débris de la machine et du bloc de
coupe
.
Examiner toutes les pièces rotatives et
coulissantes.
Vérifier le gonflage des pneumatiques. Se reporter à la section Entretien.
Vérifier le nivelage du bloc de coupe. Se reporter à la section Entretien.
Vérifier les courroies en V. Repérer toute fêlure, usure, et pièce trop
endommagée.
Vérifier le bon fonctionnement du frein. Consulter les section Fonctionnement et
Entretien.
Après fin du travail ou après les 5 premières
heures
Changer l’huile. Consulter le Manuel du propriétaire du
moteur.
Après25heures Entretien du moteur. Consulter le Manuel du propriétaire du
moteur.
Retirer, vérifier, aiguiser, et équilibrer les
lame(s).
Se reporter à la section Entretien.
Vérifier les réglages:
a. Contrôle de la rotation des lames
b. Frein
c. Embrayage
d. Direction
Se reporter à la section Entretien.
Lubrifier le châssis et le bloc de coupe. Consulter les instructions figurant dans la
section Points de lubrification.
Vérifier le pot d’échappement:
a. Couple
b. Repérer toute usure ou brûlage
c. Etat du pare--étincelles, (si présent).
Se reporter à la section Entretien.
Avant un remisage de 30 jours ou plus Préparer les moteur pour le remisage. Consulter l e Manuel du propriétaire du
moteur.
Vider les système d’alimentation. Se reporter à la section Avertissements dans le
Manuel du propriétaire.
Ajouter du stabilisateur de carburant. Consulter le Manuel du propriétaire du
moteur.
Préparer la batterie pour le remisage :
a. La retirer de la machine.
b. La charger complètement.
c. La placer dans un endroit frais et sec.
ENTRETIEN
REMARQUE : les illustrations et pictogram-
mes commencent en page 2.
Recommandations générales
1. Il est de la responsabilité de maintenir ce
produit. Cela rallongera sa durée d’utilisation.
Cette remarque est importante car si vous
n’observiez pas ces règles, vous risqueriez
de perdre votre assurance-garantie.
2. Vérifier la bougie, frein de pédale, la lubrifica-
tion de la tondeuse, et nettoyer le filtre à air
une fois par an.
3. Vérifier les attaches. S’assurer que toutes les
attaches soient bien serrées.
4. Consulter la s ection Entretien afin de garder
votre tondeuse en bon état de marche.
AVERTISSEMENT : avant de procé-
der à l’inspection, au réglages, ou
aux réparations éventuelles, -
brancher le câble de la bougie. et le retirer
afin d’empêcher que le moteur ne démarre
involontairement.
REMARQUE : le couple de torsion se mesure
en newton--mètre (pied-livre). Cette unité de
mesure permet de déterminer le couple de
serrage de l’écrou ou du boulon. Le couple
de torsion se mesure avec une clé dynamo-
métrique.
F
20
1740475
Inspection de la lame (Figure 7)
AVERTISSEMENT : avant d’inspec-
ter ou d’enlever la lame, débran-
cher le câble de la bougie. Si la
lame touche un objet, arrêter le moteur.
Voir si la tondeuse a été endommagée. La
lame est très coupante, il est donc conseil-
de porter des gants ou tout autre acces-
soire qui peut protéger vos mains.
Si vous maintenez la lame (1) coupante et veil-
lez à ce qu’elle ne s’abîme pas, les risques d’ac-
cidents en seront réduits. L’inspection de la lame
devrait être fréquente afin de déterminer l’usure,
les fissures et autres défectuosités. De même, il
faudrait vérifier fréquemment l’écrou (3) qui re-
tient la lame (1) en s’assurant qu’il reste bien
serré (3). Si la lame touche un objet, arrêter le
moteur. Débrancher le câble de la bougie. Voir si
la lame est recourbée ou endommagée. Vérifier
l’adapteur de lame (5). Avant de mettre la ton-
deuse en route, remplacer l es parties défectueu-
ses par des neuves. Consulter votre centre de
service agréé le plus proche. Tous les trois ans,
faire inspecter la lame par un professionnel
agréé ou la faire remplacer si nécessaire.
Retrait et installation de la lame (Figure 7)
1. Retirer le bloc de coupe. Cf. les instructions
dans “Retrait du bloc de coupe”.
2. Empêcher la rotation de la lame à l’aide d’un
bout de bois.
3. Retirer l’écrou (3) qui retient la lame (1).
4. Vérifier la lame (1) et l’adapteur de lame (5)
en suivant les instructions dans “Inspection
de la lame”. La remplacer par une neuve si
nécessaire. Consulter votre centre agréé le
plus proche.
5. Nettoyer le dessus et le dessous du bloc de
coupe. Retirer les débris et l’herbe.
6. Monter la lame (1) et l’adapteur de lame (5)
sur l’axe (6).
7. Monter la lame (1) de manière à ce que les
bords relevés (7) soient en hauteur. Si la
lame est à l’envers, la lame ne coupera pas
correctement et risquera de provoquer un
accident.
8. Attacher la lame (1) à l’aide des rondelles et
de l’écrou (3). S’assurer que le rebord exté-
rieur de la rondelle Belleville (2) est contre
la lame (1).
AVERTISSEMENT : veiller à ce que
l’écrou (3) soit bien serré et qu’il
retienne la lame (1). Sinon, vous
pourriez risquer un accident.
9. Attacher l’écrou (3) qui retient la lame (1) àun
couple de serrage de 41,5 Nm (30 pied-livre).
10.Installer le bloc de coupe. Cf. “Retrait du bloc
de coupe”.
Ajustement de la commande de rotation
de la lame
AVERTISSEMENT : afin de prévenir
toute blessure, la commande de
rotation de la lame doit être action-
née avec prudence.
En usage normal, la commande de rotation de la
lame ne nécessitera pas de réglage. Cependant,
si les performances de coupe faiblissent ou si la
qualité de coupe est médiocre, faire les change-
ments suivants :
1. Lors de la tonte, s’assurer que la commande
de contrôle des gaz soit en position FAST.
2. (Figure 8) Placer la commande de rotation
de la lame en position DESENGAGE (1).
3. Couper le moteur. Débrancher le câble de la
bougie.
4. Vérifier la (les) lame(s). Maintenir la lame
bien coupante ; sinon, les bouts des brins
d’herbe tourneront au marron.
5. (Figure 9) Débrancher le ressort du systè-
me de rotation de la lame (2) situé sur la
tringle de commande de la lame (1).Dé-
placer le ressort (2) vers le trou central (4).
Cela permettra d’accroître la tension sur la
courroie motrice de la tondeuse.
6. Attacher le câble à la bougie. Tondre sur une
courte distance et vérifier la qualité de la
coupe. Si nécessaire, déplacer le ressort du
système de rotation de la lame (2) vers le
trou du bas (5)
7. Vérifier encore la qualité de la coupe. Si la
qualité de la coupe n’est pas meilleure, rem-
placer la courroie motrice de la tondeuse. Cf.
“Remplacement de la courroie motrice”. Si
toutefois, si encore, rien n’y fait, amener la
tondeuse à un service agréé.
8. Déplacer la commande de rotation de la
lame en position DESENGAGE. Arrêter le
moteur.
9. (Figure 10) Vérifier le frein de lame. Faire
tourner les poulies manuellement. S’assurer
que les plaquettes de frein (7) soient bien
serrées contre les poulies.
AVERTISSEMENT : si les plaquet-
tes de frein ne sont pas serrées
correctement (7) contre les poulies,
amener la tondeuse à un centre de service
agréé.
10.(Figure 8) Placer la commande de rotation
de la lame en position ENGAGE (2).
11. (Figure 10) Vérifier les plaquettes de frein
(7). Si c elles-ci sont trop usées ou défectueu-
ses, les remplacer toutes ensemble. Un cen-
tre agréé peut vous fournir des pièces de
remplacement et de l’assistance.
12.Attacher le câble à la bougie. Tondre sur une
courte distance et vérifier la tonte. Inspecter
la commande de rotation de la lame.
13.Lorsque vous déplacez cette commande en
position DESENGAGE, tous les mouvements
s’arrêteront en cinq secondes. Si la courroie
ou la lame bougent encore, engager et dés-
engager la commande de rotation de la lame
cinq fois avant d’enlever le surplus de caout-
chouc de la courroie motrice de la tondeuse.
Si vous avez besoin d’aide, emmenez la ton-
deuse dans un centre agréé.
14.(Figure 9) Si vous remplacez la courroie
motrice de la tondeuse, mettre le ressort du
système de rotation de la lame (2) dans le
trou du haut (3).
Ajustement du levier de vitesses
(Figure 18)
Si le point mort (NEUTRAL) du levier de vitesses
ne correspond pas au point mort de la boîte de
vitesse, régler le levier de vitesses comme suit.
1. Couper le moteur.
2. Enlever l’écrou de réglage (2) du support
de levier de vitesses (3).
3. S’assurer que le levier de vitesses soit au
point mort (NEUTRAL).
4. Pousser la tondeuse. S’assurer que la boîte
de vitesses soit au point mort.
5. Afin d’aligner l’écrou de réglage (2) au trou
du support de levier (3), visser l’écrou de
réglage (2).
6. Raccrocher l’écrou de réglage (2) au sup-
port de levier (3).
7. S’assurer que le point mort (NEUTRAL) du
levier de vitesse corresponde au point mort
de la boîte de vitesse.
Vérification et réglage de l’embrayage
(Figure 11)
Si la courroie motrice de la tondeuse est lâche,
l’embrayage glissera; en pente ascendante, en
tirant une charge lourde, la tondeuse n’avancera
pas. Ajuster l’embrayage comme suit :
AVERTISSEMENT : avant toute in-
spection, réglage ou réparation de
la tondeuse, débrancher le câble de
la bougie et l’enlever afin de prévenir tout
démarrage de la tondeuse accidentel.
1. Vérifier le cheminement de la courroie motri-
ce et son installation à l’intérieur des guides
de courroie.
2. Enlever la goupille fendue (1), la rondelle
(2),etleressort du frein (3) de l’écrou de
réglage (4).
3. Retirer l’écrou de réglage (4) du bloc de
manette de frein à main (5) et de la manet-
te de frein de stationnement (6).
4. Aligner le trou de la manette de frein à main
(5) avec le trou du cadre. Bien maintenir la
manette de frein à main (5) à l’aide d’une
goupille ou d’un boulon de6mm(7).
5. Tirer la tringle d’embrayage vers l’avant
jusqu’à ce qu’elle soit bien serrée. Visser
l’écrou de réglage (4) jusqu’à ce que l’écrou
aille bien dans le trou de la manette de frein
à main (5).
6. Assembler l’écrou de réglage (4) àlama-
nette de frein de stationnement (6), ma-
nette de frein (5) et ressort du frein (3).
Attacher le tout avec la rondelle (2) et la
goupille fendue (1).
7. Retirer la goupille ou boulon de6mm(7).
8. Si la courroie glisse toujours après que l’em-
brayage ait été ajusté, c’est que la courroie
motrice est usée ou défectueuse et doit donc
être remplacée. Cf. “Remplacement de la
courroie motrice”.
Vérification et réglage du frein de
pédale (Figure 12)
Appuyer complètement sur la pédale d’embraya-
ge/freinage en avant. Mettre le frein de station -
nement. Positionner le levier de vitesses au
point mort. Pousser la tondeuse. Si les roues
arrières tournent, ajuster ou remplacer les pla-
quettes de frein. Ajuster le frein de pédale (1)
comme suit.
1 / 1

Simplicity 12.5HP / 40" MOWER Ohjekirja

Kategoria
Lawnmowers
Tyyppi
Ohjekirja
Tämä käsikirja sopii myös