Yamaha PDM-4210E Omistajan opas

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Japan QR60131



PDM-4210E

USER'S MANUAL

MANUEL UTILISATEUR

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUAL DE USUARIO

PDM-4210E

High definition plasma monitor

Moniteur plasma haute définition

G

1

ENGLISH

USER'S MANUAL

Thank you very much for purchasing the Yamaha High Definition

Plasma Monitor.

Before using your monitor, please carefully read this manual so you

will know how to operate the monitor properly. Keep this manual in a

safe place. You will find it useful in the future.

Notes on lnstallation Work:

This product is marketed assuming that it is installed by qualifed

personnel with enough skill and competence. Always have an

installation specialist or your dealer install and set up the product.

YAMAHA cannot assume liabilities for damage caused by mistake

in installation or mounting, misuse, modification or a natural

disaster.

Note for Dealers:

After installation, be sure to deliver this manual to the customer

and explain to the customer how to handle the product.

Notes about This Manual

• This information in this manual is subject to change without

notice.

• While meticulous care has been taken in the preparation of this

manual, you are requested to notify your dealer or us should

you have any comments, views or questions about our

product.

• Fully understand the prerequisites to using the product, such

as hardware and software specifications and constraints, in

using the product. We are not held liable for damages caused

by improper handling of the product.

• Reproduction of this manual in whole or in part without our prior

written permission is prohibited.

• The product names mentioned in this manual may be

trademarks or registered trademarks of their respective

owners.

READ ALL INSTRUCTIONS CAREFULLY.

KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE.

For future reference, record the serial number of your monitor.

SERIAL NO.

The serial number is located on the rear of the monitor.

2

CONTENTS

FEATURES 2

CAUTION: READ THIS

BEFORE OPERATING YOUR UNIT. 3

PRECAUTIONS 7

COMPONENT NAMES 8

Main Unit 8

Remote control 9

Loading Batteries 9

Handling the Remote Control 9

INSTALLATION INSTRUCTIONS 10

Installation 10

Anti-tumble measures 10

Connecting to a PC 11

Power Cord Connection 12

OPERATING INSTRUCTIONS 13

Turning Power On and Off 13

Input Switching 14

Volume Adjustment 14

Audio Mute 14

Size Switching 15

Input Signal Screen Display 15

Automatic Adjustment of Screen Position and the Clock 16

Independent Operation of Multiple Monitors 16

Using the Menu Screen 16

PICTURE MENU 17

AUDIO MENU 18

TIMER MENU 18

FUNCTION MENU 19

SETUP MENU 20

LANGUAGE MENU 21

OTHER FEATURES 21

Automatic Store 21

Signal Check 22

Power Save Mode 22

IMAGE RETENTION OF

PLASMA DISPLAY PANEL 23

NOTES 23

TROUBLESHOOTING 24

Symptoms That Appear to be Failures 24

Actions to Correct Abnormal Displays 26

PRODUCT SPECIFICATIONS 27

Signal Input 27

Recommended Signal List 28

SUPPLEMENT 30

Optional Video Unit Function 31

Optional Tuner Unit Function 43

Large-screen, high-definition plasma display

panel

The 42-inch colour plasma display panel, with a resolution of 1024

(H) x 1024(V) pixels, creates a high-definition, large-screen (aspect

ratio : 16:9) and low-profile flat display. Free from electromagnetic

interferences from geomagnetic sources and ambient power lines,

the panel produces high-quality display images free from colour

misconvergence and display distortion.

High Performance Digital Processor

A wide range of personal computer signals can be handled, from

640 x 400, 640 x 480 VGA to 1600 x 1200 UXGA.

Easy-to-use remote control and on screen

display system

The remote control included eases the work of setting display controls.

Further, the on-screen display system, displays the status of signal

reception and display control settings in an easy-to-view fashion.

TruBass

TruBass, SRS and (O) symbol are trademarks of SRS Labs,Inc.

TruBass technology is incorporated under license from SRS Labs,

Inc.

About the Optional Video Unit

The following functions can be obtained by connecting the optional video

unit.

(1) A Composite/S video terminal and two component terminals have

been added. A composite video output terminal is also provided

as a monitoring output.

(2) A wide range of devices other than personal computers can also

be connected.

(3) It is possible to swich the component terminal to RGB input from

the Menu screen.

(4) A SCART terminal is also provided for the signal of the European

standard. It operates as composite/S/RGB input terminal, or

video output terminal.

Options

Ask your local retail dealer for further details on the following optional

attachments.

• Wall Mounting Unit

PWK-242

• Video Unit

PTB-4210

• This User’s Manual was printed before final product development.

After printing, some product specifications may change due to

operational upgrades and other reasons. In this case, the

specifications of the product itself will take precedence over the

specifications in this manual.

• TRADEMARK ACKNOWLEDGEMENT

VGA and XGA are registered trademarks of International Business

Machines Corporation.

APPLE and Macintosh are registered trademarks of Apple

Computer, Inc.

All brand or product names are trademarks or registered

trademarks of their respective holders.

FEATURES

3

ENGLISH

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must

be taken if you are to obtain the best results and safety is to be assured.

Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the

instructions.

Never use the monitor if a problem occurs.

Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration of

liquids or foreign matter, etc. can cause a fire or electrical shock.

In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke

or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

Do not insert liquids or foreign objects.

Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present.

If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet

and contact your dealer.

• Do not place the monitor in a bathroom.

• Do not expose the monitor to rain or moisture.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.

• Do not place metals, combustibles, etc on or around the monitor.

Never disassemble or modify the monitor.

The monitor contains high voltage components. Modification could result in fire or electrical shock.

• Never remove any fixed cover.

Do not give the monitor any shock or impact.

If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact

your dealer.

Do not place the monitor on an unstable surface.

If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.

• Do not place the monitor on an unstable, slanted or vibranting surface such as a wobbly or inclined stand.

Do not obstruct the ventilation of the monitor.

If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and shorten the

lifespan of your monitor due to overheating. Make sure there is ample ventilation.

• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.

• Do not place anything around ventilation openings of the monitor.

• Never block ventilation openings.

• Do not put the plasma display panel side up.

• Do not cover the monitor with a tablecloth, etc.

• Do not place the monitor on a carpet or bedding, or near a curtain.

Use only the correct power outlet.

Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the monitor and

the safety standard.

• The enclosed power cord must be used depending on the power outlet to be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

•

Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.

• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an

appropriate extension lead or consult your dealer.

• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and

approval as the original. Ensure the fuse cover is returned to its original position.

Be sure to keep safety ground connection.

Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power cord. If

the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

Be careful in handling the power cord and external connection cables.

If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension

to the power cord and cables.

If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.

• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this

could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug

or connector.

• Do not place the cord near the heater.

• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.

• Do not touch the power plug when lightening is close to you.

• Avoid coiling the power cord and bending it sharply.

• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit from the

apparatus.

• Do not modify the power cord.

4

FOR THE CUSTOMERS IN THE U.K.

THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE

NOTES ON THIS PAGE.

IMPORTANT FOR UNITED KINGDOM

WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS

The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.

Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable

never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of

the plug. Fuse covers are available from your dealer.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to

reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician.

If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible

shock hazard by inadvertent connection to the mains supply.

WARNING: THIS EQUIPMENT MUST BE EARTHED IMPORTANT

The wires in the mains lead are coloured in accordance with the following code :

Green and Yellow = Earth, Blue = Neutral, Brown = Live.

As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth

symbol or coloured GREEN or GREEN and YELLOW.

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN

must be connected to the terminal marked with the letter L or coloured BROWN or RED.

Brown to Live

Fuse

Cord Clamp

Green & Yellow

to Earth

Blue to Neutral

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

• Do not allow the battery to be exposed to fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with metallic tweezers.

• Keep the battery in a dark, cool and dry place.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not physically impact the battery.

• Use only the battery specified in the manual of this monitor.

• Make sure the plus and minus terminals are correctly aligned when loading the battery.

• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse well

with water.

• Obey the local laws on disposing the battery.

4

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

Be careful in moving the monitor.

Neglect could result in an injury or damage.

• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.

• You are advised to move the monitor with two persons.

• Avoid any impact or shock to the monitor; particularly take care of glass screen.

Do not put anything on top of the monitor.

Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in households

where children are present.

Avoid a humid or dusty place.

Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.

• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.

Avoid a high temperature environment.

The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.

• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.

• Do not put the monitor in a place where the temperature is widely changing.

5

ENGLISH

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.

• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.

Installation environment

Do not obstruct a ventilation hole.

Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.

Do not put the monitor in the following places.

• Hot places such as near heater, place exposed to the direct rays of the sun.

• A place where the temperature is widely changing.

• Places with soot, dust or high humidity.

• Poor air ventilation place.

• Place near fire.

• A wet place such as bathroom, or shower room.

• Place where you can trip over it.

• Always vibrating or strongly vibrating places.

• Distorted or unstable places.

How to view the monitor

If you use the monitor in too dark a room, your eyes may become tired.

Please use it in a reasonably bright room.

Avoid direct rays of the sun to the screen in order to prevent eye fatigue.

Your eyes will get fatigued after viewing the monitor for long period of time.

Relax your eyes by viewing away from the monitor from time to time.

Please watch the monitor in downward direction.

Note on image retention

The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the

brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.

Tips to prevent such image retention are:

- Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,

for long.

- Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen

saver function.

- Turn down the contrast and brightness controls.

How to clean the plasma display panel of the monitor

Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.

To prevent scratching or damaging the plasma display panel face, do not knock or rub the surface with sharp or hard objects. Clean the

screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not

use harsh or abrasive cleaners.

How to clean the cabinet of the monitor

Use a soft cloth to clean the cabinet and control panel of the monitor. When the plasma monitor is excessively soiled dilute a neutral detergent

in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth.

Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially

because they would cause discoloration, scratches or cracks.

Prevention of an obstacle to Radio receivers

This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.

- Keep the monitor away from Radio.

- Adjust Radio antennas in order for the monitor not to receive interference.

- The antenna cable of Radio should be kept away from the monitor.

- Use a coaxial cable for antenna.

You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.

If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.

Precautions for the cable connection

- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are

properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing

connections.

- Confirm the connector is fixed tightly when the signal cable is connected.

Also confirm the screws on the connector are tightened.

- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..

- Use a plug with ground terminal and make sure that it connects to the ground.

6

Precaution during transportation

Please pay attention when you transport this monitor because it is heavy.

Furthermore, use the original carton box and its packaging materials when the monitor is transported.

Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.

Save the original carton box and all packing material.

Do not physically impact the remote control.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place heavy objects on the remote control.

Avoid strong rays.

Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause distorted images or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.

Set the sound volume at a suitable level.

It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.

Precautions for the installation

- Do not use makeshift pedestals and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved

pedestal or legs with the fixings provided according to the instructions.

- Use only with the cart, pedestal, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury from tip-over.

- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the

front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.

- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

- Only use the attachments/accessories specified by the manufacturer.

- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.

Other precautions

- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a

stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or

handicapped people.

- Disposal of this product may require specific instructions pertaining to your resident region.

- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

7

ENGLISH

PRECAUTIONS

• Please read this User's Manual thoroughly, especially the "CAUTION:READ THIS BEFORE OPERATING YOUR UNIT." and the "PRECAUTIONS"

sections. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you

encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual.

In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your

dealer immediately.

• Under no circumstances remove the rear cover of your plasma monitor.

Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

• It is prohibited for the end user of this product to copy, reverse engineer or reverse compile the software included therein, save to the extent

permitted by law.

• After the plasma monitor has been turned on for any length of time, you will notice that the screen becomes warm. Please note that this is

normal. Sometimes the screen might have some tiny bright or dark spots. Please note that this is normal.

• To prevent scratches or damages to the plasma display panel, do not knock or rub the surface with sharp or hard objects.

8

Caution when moving the main unit

• As this product is heavy, whenever it is moved, two

people are required to transport it safely.

• Whenever the unit is moved it should be lifted forwards

using the two handgrips at the back, and the unit should

then be held at the base on both sides for stability.

COMPONENT NAMES

Front

Cabinet

(front frame)

Panel

Remote-control

receiver

9

SIZE button

( SELECT button)

15

INPUT SELECT button

(OK button)

14

RECALL button

( SELECT button)

15

• Adjustment buttons are located

on the

bottom

.

• The back cover is provided with

indications to distinguish the

adjustment buttons.

SUB-POWER button

13

Control panel

VOLUME

UP/DOWN

buttons

( ADJUST

buttons)

14

Main power switch

13

• The main power switch is located at the back, on the

lower surface.

Indicating lamp

External device connection terminals

Rear

RGB input terminals

11

External

speaker

terminals

Handgrips

HandgripsHandgrips

Main Unit

External

speaker

terminals

11

MENU button

16

• ( ) indicates the function while the MENU is displayed on the screen.

▼

Pedestal

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

9

ENGLISH

Remote control

ID SET button

16

POWER OFF button

13

POWER ON button

13

POWER ON/OFF button

13

MENU button

16

MUTE button

14

VOLUME UP/DOWN buttons

14

RETURN button

16

RECALL button

15

AUTO button

16

PinP button

34

ID button

16

SELECT/ADJUST buttons

16

OK button

16

Loading Batteries

1. Open the battery cover.

• Slide back and remove the battery

cover in the direction of the arrow.

2. Load the batteries.

• Load the two Size AA batteries included, matching polarity

markings on the batteries to those on

the case.

3. Close the battery cover.

• Replace the battery cover in the direction of the arrow and snap

it back into place.

Use the remote control within about 5 m from the front of the unit,

within a 30 degree arc either side of the remote control sensor.

With in 30

degrees

About 5m

About 3m

With in 30

degrees

About 3m

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

CAUTION

• Do not use new and old batteries together. The batteries could

explode or leak, resulting in fires, physical injury, or stains.

• When loading batteries, observe their correct polarities as

marked on the product. If loaded in the wrong direction, the

batteries could explode or leak, resulting in fires, physical injury,

or stains.

ATTENTION

• Do not drop exert undue force on the remote control.

• To avoid possible failures. Do not splash the remote control with

water or put it on a wet object.

• It you do not intend to use the remote control for an extended

period of time, remove the batteries from it.

• If the remote control begins to lack responsiveness, replace the

batteries.

• Strong light such as direct sunlight impinging on the

photoreceptor of the remote control can cause operational

failure. Position this unit to avoid direct contact with such light.

Handling the Remote Control

SIZE button

15

RGB/VIDEO buttons

14

COMPONENT NAMES

(continued)

10

Anti-tumble measures

Securing to a wall or pillar

Use a commercially available cord or chain, and a clamp to secure the set to a firm wall or pillar.

Securing to desktop

1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the pedestal as shown.

2) Using commercially available wood screws, secure the set firmly in position.

• When installing the monitor, use the pedestal.

The pedestal has been used for the illustrations in this manual.

INSTALLATION INSTRUCTIONS

Installation

CAUTION

• Use one of the special mount units to install this product. A mount of insufficient strength or inadequate

design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our

company assumes absolutely no responsibility for personal injuries or property damage caused by use of

other mount units or improper installation.

• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work

yourself. Ask your dealer to provide the name of a qualified installer.

• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop set-

up) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not

blocked.(

✻

)

CAUTION

Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.

10cm (4 inches) or more*

Cord

or

chain

Clamp

Two places

Wood screw

Hook

Chain

cord or chain for 42"

clamp for 42"

Wall or Pillar

Hook

11

ENGLISH

Read CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. and PRECAUTIONS ( to )

carefully to ensure maximum safety before proceeding to these steps:

• Choose a safe level location to install the product.

• Install the monitor to have ready access to a power socket available.

• Make sure that the power switch of this device is turned off.

73

(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this

device.

• See "Product Specifications" concerning the specifications of this device.

(2) Make sure that the power switch of the personal computer is turned off.

(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output

terminal of the personal computer.

• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.

• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with

the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the

personal computer manufacturer or your local retail dealer.

Connecting to a PC

(RS-232C)

Fo

r

custo

m

e

r

i

n

stallatio

n

Monitor rear panel

Power cord

Power cable

connector

Speaker (R)

Speaker (L)

PC

(

D-sub

)

(

DVI

)

T

o s

ig

na

l

out

p

ut

te

rm

i

n

al

T

o s

ig

na

l

out

p

ut

te

rm

i

n

al

To

audio

out

p

ut

terminal

3

.

5

mm

Ste

r

eo

m

i

n

i

j

ac

k

EUROPE U.K. ONLY

27 29

~

INSTALLATION INSTRUCTIONS

(continued)

12

①

Connect the power cord to this device.

➁

Connect the power cord plug to the power outlet.

(The type of plug is different from this drawing for some countries.)

Connect the power cord after completing all other connections.

EUROPE U.K. ONLY

1

2

1

2

INSTALLATION INSTRUCTIONS (continued)

Power Cord Connection

CAUTION

• Use only the power cord provided.

• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

13

ENGLISH

OPERATING INSTRUCTIONS

Turning Power On and Off

• To turn the monitor power on, press the main power

switch on the monitor main unit to ON, and then press

the SUB POWER button or the ON/OFF or ON button on

the remote control.

• To turn the monitor power off, press the SUB POWER

button or the ON/OFF or OFF button on the remote

control, and then set the main power switch on the

monitor main unit to OFF.

• During normal use, the main power switch is set in the ON

position, and the monitor can then be turned ON/OFF using the

SUB POWER button or the ON/OFF button on the remote

control.

Indicating lamp

Indicating

lamp

Power status Operating

Off Off

When the main power switch is set

to OFF.

Lights red

Off

(standby)

When the main power switch is

ON, and the OFF button on the

remote control or the SUB POWER

button on the underside of the

front of the frame is OFF.

Lights green On

When the main power switch is

ON, and the ON button on the

remote control or the SUB POWER

button on the underside of the

front of the frame is ON.

Lights orange

Off

(Power Save)

When the main power switch is

ON, and the ON button on the

remote control or the SUB POWER

button on the underside of the

front of the frame is ON.

However, the indicator also light orange

when the unit is in POWER SAVE mode.

When the indicating lamp lights in orange or the message “No Sync.

Signal”, “Power Save” or “Invalid Scan Freq.” appears on the

screen, see “Power Save Mode” or “Symptoms that Appear to be

Failures.”

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

POWER OFF

button

POWER ON

button

POWER ON/OFF

button

SUB-POWER button

Main power switch

Indicating lamp

ATTENTION

• Avoid repeatedly turning the monitor on and off at short

intervals. Failures might result from such operation.

• Turn off the main power switch if you do not plan to use the

monitor for an extended period of time.

• If a power failure occurs while the main unit is running, it will be

powered on upon recovery from the failure. Turn off the unit

main power switch before you leave the area in which the main

unit is located.

22

24

14

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

OPERATING INSTRUCTIONS (continued)

Audio Mute

The audio volume can be temporarily muted by pressing

the MUTE button of the remote control.

• When a button is pressed, the volume adjustment

status guide (magenta) will be displayed.

• The volume setting can be lowered by pressing the VOL- button

while the audio is mute.

• The muting can be cancelled by pressing the VOL+ button or

MUTE button while the audio is mute.

When the MUTE button of the remote control is pressed

again, the audio will be restored and the volume display

(green) will appear.

MUTE button

Input Switching

•

Input can be switched by pressing the RGB1, RGB2,

buttons of the remote control.

•

Input can be switched in the sequence of RGB1

➔

RGB2 by pressing the INPUT SELECT button of the

monitor.

• When a button is pressed, the volume adjustment

status guide will be displayed.

• The volume will increase when the VOL+ (or

▲

) button is

pressed while the guide is being displayed.

• The volume will decrease when the VOL- (or

▼

) button is

pressed while the guide is being displayed.

Volume Adjustment

The volume can be adjusted by pressing the VOL+ and

VOL- buttons of the remote control (or the

▲

and

▼

volume buttons of the monitor unit).

Volume 15

Volume setting value

Adjustment status guide display

VOLUME

UP/DOWN buttons

INPUT SELECT button

RGB buttons

Adjustment status guide display

(The display colour will change to magenta.)

VOLUME UP/DOWN

buttons

RGB1 RGB2

Volume 15

Volume setting value

▼

15

ENGLISH

Size Switching

Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in

sequence and the status will be displayed at the bottom of the screen.

* Real mode gives an image of the same shape as it is displayed on a computer monitor.

This mode is only available for VGA (640 X 480) and WVGA (864 X 480).

Normal Full Zoom1

Real Zoom3 Zoom2

SIZE button

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

SIZE button

RECALL button

Input Signal Screen Display

The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the

monitor.

• The display will go out in approximately 6 seconds.

RECALL button

*

Display area selection diagram (RGB input)

Resolution Full display Circular display

Display Full Normal Real Zoom1 Zoom2 Zoom3

640 X 480

(VGA)

800 X 600

(SVGA)

1024 X 768

(XGA)

1280 X 1024

(SXGA)

1600 X 1200

(UXGA)

Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that

flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On can reduce

the flicker.

* VGA and W-VGA

only

20

RGB2

RGB

H : 48.4kHz

V : 60.1 Hz

-- -- Min.

-- -- : -- --

OFF

Input mode

Signal mode

Input horizontal frequency

Input vertical frequency

Off-timer

On-timer

RGB

OPERATING INSTRUCTIONS (continued)

16

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

VOL

AV4

AUTO PinP

OK

SIZE RECALL

MENU

ID

ID SET

ID SET button

ID button

AUTO button

Using the Menu Screen

(On-screen display system)

When the MENU button is pressed, the adjustment menu

screen will be displayed; from there, PC signal

adjustment and setting is possible by using the SELECT

button, ADJUST button and OK button.

• Refer to - concerning the adjustment items and the

settings.

Example: Selecting the Picture screen

1. Press the MENU button to display the Main Menu

screen.

2. Press the OK button to display the Picture Menu

screen. (Use the and SELECT buttons to select

other items.)

3. Use the and SELECT buttons to select the item to

be adjusted and then use the and ADJUST

buttons to adjust (example: Contrast).

• Press the RETURN button to return to the previous screen.

• If there is no operation for a period of one minute, the

Adjustment Menu screen will be closed automatically.

MENU

OK

Picture

Contrast : + 31

Brightness : – 31

Colour : 0

Hue : + 31

Picture Enhancement : Off

Colour Temperature : Normal

Colour Temp.Adjust

Reset Reset

Select Return Exit

OPERATING INSTRUCTIONS (continued)

Independent Operation of

Multiple Monitors (ID No)

Setting the ID No. of the remote control allows separate

control of up to a maximum of seven monitors.

Remote control ID No. 2 (initially ID no. 1) can be set by

pressing the ID SET button for 2 sec. or more while

holding down the ID button. The number will be

incremented (2•••6

➔

7

➔

1

➔

2) when this button pressed

continuously.

The ID remote control is operated by pressing the

various buttons while holding down the ID button;

Operation is possible only when the remote control and

monitor ID nos. are the same.

• The remote control can be operated normally by pressing the

various remote control buttons without holding down the ID button.

• Set the monitor using the ID No. of Function MENU.

Automatic Adjustment of

Screen Position and the Clock

Adjustment of the screen to a position suitable for the

PC signal and the clock adjustment can be performed

automatically by pressing the AUTO button of the remote

control.

* Depending on the signal, satisfactory adjustment may not be

possible in some cases. In such cases, adjust by referring to the

Setup Menu item.

ID Number

Monitor [ 1 ]

R/C [ 1 ]

Monitor ID no.

Remote control ID no.

The remote control ID no. can be

checked by pressing the ID SET button

while holding down the ID button.

CAUTION

Perform this adjustment for each input (RGB1 or RGB2) and for

each signal.

19

17

21

MENU button

OK button

SELECT/ADJUST

buttons

RETURN buttons

Picture

Audio

Timer

Function

Setup

Language

Select

OK Set

Contrast + 31

Next / Prev Adjust Return

17

ENGLISH

PICTURE MENU

Picture

Audio

Timer

Function

Setup

Language

Select

OK Set

Picture

Contrast : + 31

Brightness : – 31

Colour : 0

Hue : + 31

Picture Enhancement : Off

Colour Temperature : Normal

Colour Temp.Adjust

Reset Reset

Select Set Return

OK

Picture

Contrast : + 31

Brightness : – 31

Colour : 0

Hue : + 31

Picture Enhancement : Off

Colour Temperature : Normal

Colour Temp.Adjust

Reset Reset

Select Set Return

OK

MENU

Picture

Colour Temp. Adjust On

Amplitude

Red – 63

Green 0

Blue – 31

Cut Off

Red + 31

Green 0

Blue + 31

Reset Reset

Select On/Off Return

Contrast + 31

Next / Prev Adjust Return

OK

Picture

Contrast : + 31

Brightness : – 31

Colour : 0

Hue : + 31

Picture Enhancement : Off

Colour Temperature : Normal

Colour Temp.Adjust

Reset Reset

Select Set Return

OK

Colour Temperature Normal

Next / Prev Select Return

Selected characters Setup hint

Contrast

Narrows the gap between

brightness and darkness.

Broadens the gap between

brightness and darkness.

Adjust for maximum visibility to suit the ambient brightness.

Adjust further till [+40] by pressing and holding cursor

button at

[+31]. The color for [+32] to [+40] numbers will change from white to

magenta. This special mode is better for dark scenes.

For brighter scene some parts of the picture might not be clear. We

recommend to set at [+31].

"Panel Life" in the Function Menu should be set to Normal when

Contrast setting is adjusted.

Brightness

Black is subdued for

increased overall darkness.

Black is set off for increased

overall brightness.

Adjust to taste.

Colour

Darkens colours. Lightens colours. Adjust to taste.

Hue

Enhances red and weakens

green.

Enhances green and weakens

red.

This is not available for adjustment when receiving PAL/SECAM signal.

In this case the character will be grayed out.

Adjust for the most realistic skin colour.

Picture Enhancement

Off Low Middle High

Sets the clarity of small details to the desired level.

Colour Temperature

Cool Normal Warm Black / White

Normally set to Normal.

Colour Temp. Adjustment

Off On

Turn On when you wish to change colour temperature to suit user

preferences.

Amplitude

Red

Brighter scenes are

decreased in reddish colour.

Brighter scenes are increased

in reddish colour.

Adjust colour temperature to suit user preference. These settings are

independently stored in each of the 4 Colour Temperature modes.

Green

Brighter scenes are

decreased in greenish colour.

Brighter scenes are increased

in greenish colour.

Blue

Brighter scenes are

decreased in bluish colour.

Brighter scenes are increased

in bluish colour.

Cut Off

Red

Dark scenes are decreased in

reddish colour.

Dark scenes are increased in

reddish colour.

Green

Dark scenes are decreased in

greenish colour.

Dark scenes are increased in

greenish colour.

Blue

Dark scenes are decreased in

bluish colour.

Dark scenes are increased in

bluish colour.

Reset

(Selects the Reset mode)

The original factory settings for the items of this Menu page can be

restored by pressing the OK button.

▼

OPERATING INSTRUCTIONS (continued)

18

Selected characters Setup hint

Audio Mode

Movie Music Speech Favourite

Movie: This selects the audio mode suitable for Movies.

Music: This selects the audio mode suitable for Music.

Speech: This selects the audio mode suitable for News, Talk show

etc.

Favourite: This mode should be adjusted to suit your preference.

Treble

Suppresses treble. Enhances treble. Adjust to taste.

Bass

Suppresses bass. Enhances bass. Adjust to taste.

Balance

Suppresses right-side sound. Suppresses left-side sound. Adjust to taste.

SRS TruBass

Off Low Middle High

SRS TruBass takes advance of the ability of the human ear to

distinguish between two different tones. By using this ability, TruBass

gives enhanced bass sound that otherwise would not be heard.

Adjust it depending on the user’s preference.

Matrix Surround

Off On

This features the spacious sound effects of a stadium.

Perfect Volume

Off On

This will automatically adjust volume so each channel and input has

the same average volume level.

Reset

(Selects the Reset mode)

The original factory settings for the items of this Menu page can be

restored by pressing the OK button.

Picture

Audio

Timer

Function

Setup

Language

Select

OK Set

Audio

Audio Mode : Movie

Treble : + 10

Bass : – 10

Balance : 0 L R

SRS TruBass : Middle

Matrix Surround : Off

Perfect Volume : Off

Reset Reset

Select Set Return

OK

MENU

AUDIO MENU

Picture

Audio

Timer

Function

Setup

Language

Select

OK Set

Timer

Off Timer : 30Min.

On Timer : - - : - -

Select Adjust Return

OK

MENU

TIMER MENU

Selected characters Setup hint

Off Timer

--Min. 30Min. 60Min.

120Min. 90Min.

This function automatically sets the power to standby status when the

indicated time period has elapsed.

On Timer

- - ( : - - )

hours

(- - : )- -

minutes

This automatically sets the power from standby to ON when the

indicated time period has elapsed. The settable time is 00:00~11:59.

Input the required time by SELECT buttons on the remote

control.

OPERATING INSTRUCTIONS (continued)

▼

19

ENGLISH

Picture

Audio

Timer

Function

Setup

Language

Select

OK Set

Function

Screen Saver Off

Screen Wipe On 60Min.

Black Side Panel Off

Video Power Save Off

Freeze Mode Split

Default Zoom Panoramic

Reset Reset

Select Set Return

OK

MENU

FUNCTION MENU

Function

Panel Life Normal

Mode Display Off

ID Number 1

Inverse On 60Min.

Standby White Off

Gamma 2.2

Reset Reset

Select Set Return

Selected characters Setup hint

Screen Saver

Off 5Min. 10Min.

60Min. 40Min. 20Min.

This moves the picture around the screen in small amounts, at set

intervals, to reduce the panel image retention. Image retention

occurs when stationary objects, such as screen logos, leave a slight

image visible after they should have disappeared.

Screen Wipe

On 60Min.

This is used to reduce the panel image retention that can occur with

stationary pictures by displaying a completely white screen. Select

On (continuous operation) or 60 Min. (time limit operation) and press

the OK button. Press the MENU or RETURN button on the remote

control to return to normal viewing.

Black Side Panel

Off On

This turns the gray sidebars On/Off when watching normal mode

screen size area. It is always set to Off when the monitor is powered

On. It is recommended to set Black Side Panel to off to reduce the

panel image retention.

Video Power Save

Optional (grayed out)

Freeze Mode

Optional (grayed out)

Default Zoom

Optional (grayed out)

Reset

(Selects the Reset mode)

The original factory settings for the items of this Menu page can be

restored by pressing the OK button.

Panel Life

Normal Extend 1 Extend 2

This function suppresses the contrast of the screen regardless of the

Contrast setting in the Picture Menu. By this control, power

consumption can be reduced or degradation of a panel can be

mitigated.

The order of power consumption is Extend 2 < Extend 1 <

Normal.

If the Contrast setting is changed when this item is set to Extend 1 or

2, it will be changed to Normal automatically.

Mode Display

Off On

This functions displays the Input Signal Screen Display every time the

input mode and signal mode are changed.

Set to OFF if the Input Signal Screen Display is not needed when

switching signals.

ID Number

1 2 3 4

7 6 5

Assigns ID nos. to the monitors so that they can be controlled

individually (up to 7 monitors can be controlled).

Inverse

On 60Min.

This function changes each level of RGB signal invert to reduce the

panel image retention. When this function is required, select On

(continuous operation) or 60Min. (time limit operation) and press the

OK button. And press the Menu or Return button to exit.

Standby White

Off 15Min. 30Min.

120Min. 60Min.

This function is also provided to prevent image retention. If time is set

for this item, the screen changes into a white pattern when the

monitor enters power save mode, and continues for the period of

setting time.

Gamma

2.2 2.8

Normally set to 2.2.

▼

OPERATING INSTRUCTIONS (continued)

Sivu latautuu ...

Yamaha PDM-4210E Omistajan opas

Yamaha PDM-4210E Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat