Yamaha YRS-2100 Omistajan opas

Printed in Indonesia WW75150-1

Surround sound TV stand

Meuble TV surround

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Rear: 5 cm (2 in)

Sides: 5 cm (2 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press p to set this unit to the

standby mode, and disconnect the AC power plug from the

wall outlet.

18 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

19 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

20 Excessive sound pressure from earphones and headphones

can cause hearing loss.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by p. This state is called the standby mode. In this state, this unit

is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below. Note that the plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED. Make

sure that neither core is connected to the earth terminal of the three

pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

Notes

• This unit’s speakers use magnets. Do not place items that are

sensitive to magnetism, such as CRT-type TVs, clocks, credit

cards, floppy disks, etc., on top of the rack.

• When the unit is positioned close to a CRT-type TV, picture or

sound distortion may occur. In this case, move the TV away from

the unit.

i En

1 En

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following places:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or a

stove

– places of extremely low temperatures

– dusty places

• Do not expose the remote control sensor of this unit to direct

sunlight or lighting such as inverted fluorescent lamps.

• If the batteries grow old, the effective operation range of the remote

control decreases considerably. If this happens, replace the batteries

with two new ones as soon as possible.

• Change all of the batteries if you notice the following conditions:

the operation range of the remote control decreases or the

transmission indicator does not light up or becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and color.

• Exhausted batteries may leak. If the batteries have leaked, dispose

of them immediately. Avoid touching the leaked material or letting it

come into contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

• Do not throw away batteries with general house waste. Dispose of

them correctly in accordance with your local regulations.

2 En

What you can do with this unit

To enjoy TV

To enjoy Blu-ray

movies

To enjoy games

Checking supplied accessories (p. 4)

Installation (p. 5)

Preparing the remote control (p. 7)

Connecting your TV and Blu-ray disc player (p. 8)

Operating the unit by TV’s remote control (p. 18)

When enjoying STB program

such as on satellite/CATV tuner

(p. 9)

Connecting a game

console (p. 9)

Playing back a TV, Blu-ray disc player, and game console (p. 20)

PREPARATION

CONNECTION/

INITIAL SETTINGS

PLAYBACK

Setting the best possible sound automatically (p. 11)

HDMI link (HDMI control)

function

p. 18

Cinema DSP function

p. 22

IntelliBeam function

p. 11

Headphone surround function

p. 26

UniVolume

p. 21

Playing back iPod/iPhone

p. 29

3 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

Contents

PREPARATION

Getting started .......................................................4

Supplied accessories .................................................... 4

CONNECTION/INITIAL SETTINGS

Installation..............................................................5

Remote control preparation........................................... 7

Connections...........................................................8

TV and Blu-ray disc player connection.......................... 8

Game console or tuner connection ............................... 9

Initial settings.......................................................10

Selecting language for menu display .......................... 10

Auto setup for appropriate surround effects

(IntelliBeam)........................................................... 11

Operating the unit by TV’s remote control................... 18

PLAYBACK

Playback features ................................................ 20

Basic operation for playback....................................... 20

Enjoying sound with your preference.......................... 21

Switching stereo/surround sound....................................... 21

Playing back digitally compressed formats (MP3, WMA, etc.)

with enriched sound (Compressed Music Enhancer)......... 21

Automatic volume level adjustment (UniVolume)............... 21

Volume balance adjustment...............................................21

Enjoying realistic surround sound (CINEMA DSP).............22

Changing the audio output method for surround playback........23

Surround decoder setting................................................... 25

Using useful features .................................................. 26

Listening with headphones................................................. 26

Sleep timer/auto power down function ............................... 27

Settings for each input source (Option menu)....................27

Playing back iPod/iPhone ........................................... 29

When using Yamaha Universal Dock for iPod (optional

YDS-12, etc.) ....................................................................29

When using Wireless System for iPod (optional YID-W10).......29

Playing back Bluetooth components........................... 30

Pairing ................................................................................30

Connecting ......................................................................... 31

SETTINGS

Setup menu...........................................................32

Setting procedure........................................................32

Setup menu list............................................................33

Manual setup...............................................................34

Setting parameters ........................................................... 34

Beam adjustment.............................................................. 35

Image location .................................................................. 36

Tone control ................................................................36

Tone control...................................................................... 36

Subwoofer settings ........................................................... 36

Audio delay control ........................................................... 36

Dynamic range control...................................................... 37

Volume level of each channel with test tones ................... 37

Sound out setting ........................................................37

Sound beam output configuration ..................................... 37

Input assignment.........................................................38

Input assignment .............................................................. 38

Input rename..................................................................... 39

HDMI setup....................................................................... 39

DISPLAY MENU ............................................................... 40

Advanced setup ...................................................41

TROUBLESHOOTING

Troubleshooting...................................................42

ABOUT THIS UNIT

Controls and functions........................................46

Glossary................................................................49

Specifications.......................................................51

Using the supplied demonstration DVD.............53

Index......................................................................54

About this manual

• In this manual, operations that can be performed using either the front panel buttons or the remote control are explained using the

remote control.

•

y indicates a tip for your operation.

• Notes contain important information and operating instructions.

• This manual is produced prior to production. Design and specifications are subject to change in part as a result of improvements,

etc. In case of differences between the manual and the product, the product has priority.

• The alphabet mark (such as ) indicates the remote control key(s) indicated on the figure on the left page.

4 En

PREPARATION

Getting started

Before assembly and connecting, make sure you have received all of the following items.

1)

Supplied accessories

Remote control Battery (× 2)

(AA, R6, UM-3)

Optical cable

(1.5 m (4.9 ft))

Video pin cable

(for displaying menu

and iPod video)

(1.5 m (4.9 ft))

Install Manual

Owner’s Manual

(this manual)

Main unit

IntelliBeam microphone

(× 1) (6 m (19.7 ft))

Cardboard microphone

stand (× 1)

Quick Reference Guide

Digital audio pin cable

(1.5 m (4.9 ft))

Demonstration DVD

(☞p. 53)

Assembly is required before using this unit. Make sure all of the following items are included in the package, as they are all

necessary to complete assembly. Refer to the Install Manual for installation.

• Main unit • Rear panels (left and right)

• Shelf • Support posts

• Bottom panel • Center rear panel

• Glass top panel • Brackets

• Pins • Small screws M4 × 10 mm

• Large screws M5 × 30 mm • Washers

• Fasteners

According to the connection, the supplied cables may not be needed.

1) y

5 En

CONNECTION/INITIAL SETTINGS

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

Installation

Place the unit in the appropriate position after assembly. Refer to the supplied Install Manual for assembly. This section describes a

suitable installation location to install this unit. Refer to “Notes on installation” below and place the unit correctly in the safe place.

This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround sound effects

produced by this unit may not be sufficient when this unit is installed in the following locations.

• Rooms with walls inadequate for reflecting sound beams

• Rooms with acoustically absorbent walls

• Rooms with measurements outside the following range: W (3 to 7 m (10 to 23 ft)) × H (2 to 3.5 m (7 to 11.5 ft)) × D (3 to 7 m (10 to

23 ft))

• Rooms with less than 1.8 m (6 ft) from the listening position to this unit

• Rooms where objects such as furniture are likely to obstruct the path of sound beams

• Rooms where the listening position is close to the walls

• Rooms where the listening position is not in front of this unit

■ My Surround

In the room such as above, you can enjoy rich surround effects by My Surround (☞p. 24).

Before installing this unit

Notes on installation

• Install your TV in accordance with the manufacturer’s instructions to prevent it from toppling over.

• This unit’s speakers use magnets. Do not place items that are sensitive to magnetism, such as clocks, credit cards, floppy disks, etc., on top of the

rack.

• When the unit is positioned close to a CRT-type TV, picture or sound distortion may occur.

Caution: Handling the tempered glass

The top glass panel is constructed of glass that has been tempered for strength and safety. In addition, a safety film has been applied to the tempered

glass to offer additional protection against injuries that may be caused by shattering glass. However, if you handle the glass inappropriately, the glass

might break and glass fragments might fly, causing injuries. Be sure to follow the precautions listed below:

• Do not allow any strong impacts to the glass (for example, do not allow thrown objects to strike the glass).

• Do not allow sharp objects to contact the glass.

• If the tempered glass has been scratched, it might break unexpectedly. If you see scratches, replace the glass immediately.

• Do not remove the glass caution sticker.

Maximum

load

50kg

15kg

30kg

Interior slide sheet

An interior slide sheet is attached to the

bottom of the unit, allowing you to

move the unit into position easily. To

prevent damage to the floor, clean the

floor of dust and rubbish before moving

the unit.

YRS-2100

YRS-1100

• Install this unit in the center of the left and right walls.

• Listening position (such as sofa, etc.) should be located at the

front of the unit.

• The distance between listening position and the unit should be

more than 1.8 m (6 ft).

YRS-1100

Maximum load

80kg

10kg each

(Left, center

and right)

40kg

YRS-2100

Installation

6 En

This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture

obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved.

You may install this unit in parallel with the wall or in the corner.

■ Installation examples

Parallel installation

Install this unit as close to the exact center of the wall as possible.

Ideal installation condition

Install this unit as close to the exact front of your normal listening position as possible.

The distance between listening position and the unit should be more than 1.8 m (6 ft).

Installing this unit

Parallel installation

Install this unit in the exact center of the wall when it is measured

from the left and right corners

Corner installation

Install this unit in the corner at a 40° to 50° angle from the

adjacent walls.

An object, such as furniture

40° to 50°

Parallel installation

(with 5Beam)

Corner installation

(with Stereo+3Beam)

Installation

7 En

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

Installing in a non-square room

Install this unit so that the sound beams can be reflected off the walls.

Before installing batteries or using the remote control, make sure that you read precautions on the remote control and batteries in

“CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.”

Remote control preparation

Installing the batteries

Battery × 2

(AA, R6, UM-3)

Press U

Remove the transparent sheet before using.

Operation range

Within 6 m (20 ft)

8 En

Connections

For the cable connection, follow the orders below.

TV and Blu-ray disc player connection

1

HDMI cable

(optional)

Input the digital audio/

video signals of the Blu-

ray disc player to this

unit.

2

HDMI cable

(optional)

The digital video of the

Blu-ray disc is reflected

on TV.

3

Optical cable

(supplied)

Play back digital sounds

of TV on this unit.

4

Video pin cable

(supplied)

To display the YRS-

2100/YRS-1100’s setup

menus on the TV.

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or terminal.

123

INPUT1

INPUT2

HDMI INPUT

OPTICAL

OUTPUT

VIDEO

AUDIORL

HDMI

OUTPUT

To AC wall outlet

Blu-ray disc player

1. Remove the cap

2. Check the direction of

the plug

TV

Video signals

Audio signals

1

2

3

(Example)

1)

4

2)

Audio return channel (ARC) supported TV

• Connect HDMI cable to audio return channel supported terminal (the

terminal with “ARC” indicated) on TV. In this case, you do not need

to connect optical cable.

• Activate the HDMI control function of this unit (☞p. 39).

What is audio return channel (ARC)?

A function transmits digital audio signal output from TV to this unit

through a HDMI cable. By this function, a digital audio pin cable to

connect TV and this unit is not needed.

Depending on the setting, HDMI for video signal and optical digital

audio, coaxial digital audio or analog audio for audio signal can be

selected. Refer to “Input assignment (☞p. 38)”.

1) y

2) y

Connections

9 En

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

Game console or tuner connection

Additional external device (example) Connecting cable

1 HDMI supported game console

HDMI cable (optional)

2 Satellite/cable TV (HDMI supported)

HDMI cable (optional)

3 Satellite/cable TV (HDMI not supported)

Digital audio pin cable (supplied)

4)

4 HDMI not supported game console

Analog audio stereo pin cable (optional)

4)

HDMI

OUTPUT

HDMI

OUTPUT

ANALOG

OUTPUT

COAXIAL

OUTPUT

VIDEO

INPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

VIDEO

INPUT

Video signals

Audio signals

TV

1 2 3 4

3)

(Example)

4)

To AC wall outlet

(Example)

4)

(Example)

The additional devices having an optical digital output jack, connect to

the optical digital input jack of this unit with an optical cable.

To connect a game console or tuner to TV, you need extra video pin

cables (optional).

3) y 4) y

10 En

Initial settings

Selecting language for menu

display

1

Turn the unit and your TV on.

2

Switch TV’s input to “VIDEO INPUT 1

(example)”.

Check whether the initial screen is displayed.

1)

3

Press and hold SETUP key until the

“LANGUAGE SETUP” menu appears on

your TV.

4

Press U / V key to select the desired

language and then press ENTER key.

Selectable item: ENGLISH, DEUTSCH, FRANÇAIS,

ESPAÑOL, ITALIANO, NEDERLANDS, РУССКИЙ,

SVENSKA

Initial setting: English

YRS-

2100

Push [SETUP] to

begin SETUP MENU.

(example)

[ ]/[ ]:Sel [ENTER]:Return

3)LANGUAGE SETUP

When the screen is not displayed

Confirm the case followings.

– The input jack of your TV and the video output jack of the unit are

connected.

– The input of your TV is set to “VIDEO INPUT 1 (example)”.

1) y

11 En

Initial settings

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

This unit creates a sound field by reflecting sound beams on the

walls of your listening room and by broadening the cohesion of

all the channels. Just as you would arrange the speaker position of

other audio systems, you need to set the beam angle to enjoy the

best possible sound from this unit.

This unit employs the beam optimization and sound optimization

features with the aid of the supplied IntelliBeam microphone, allowing

you to avoid troublesome listening-based setup and achieving highly

accurate sound adjustments that best match your listening

environment. We call these two features “IntelliBeam” generically.

Beam optimization:

This feature optimizes the beam angle so that the parameter best

matches your listening environment.

Sound optimization:

This feature optimizes the beam delay, volume, and quality so

that the parameters best match your listening environment.

This unit performs these two automatic optimizations with the aid

of the supplied IntelliBeam microphone.

2)

Follow the procedure below to connect the IntelliBeam

microphone to this unit and place it in a proper location.

Auto setup for appropriate

surround effects (IntelliBeam)

Installing the IntelliBeam microphone

1

Place the IntelliBeam microphone on a flat

level surface at your normal listening position.

Use the supplied cardboard microphone stand or a tripod

to place the IntelliBeam microphone at the same height as

your ears would be when you are seated.

■ Assembling the supplied cardboard

microphone stand

• The AUTO SETUP procedure may not be run successfully if this

unit is installed in one of the rooms described in “Installing this

unit” on page 6. In such cases, run MANUAL SETUP (☞p. 14) to

manually adjust the corresponding parameters.

• Do not connect the IntelliBeam microphone to an extension cable

as doing so may result in an inaccurate sound optimization.

• After you have completed the AUTO SETUP procedure, be sure

to disconnect the IntelliBeam microphone.

• The IntelliBeam microphone is sensitive to heat.

– Keep the IntelliBeam microphone away from direct sunlight.

– Do not place the IntelliBeam microphone on top of this unit.

Note

1 2 3

54

Remove

Fit in

Run

through

Place

horizontally

Fit in

Make sure that there are no obstacles between the

IntelliBeam microphone and the walls in your listening

room as these objects obstruct the path of sound beams.

However, any objects that are in contact with the walls

will be regarded as a protruding part of the walls.

2

Check if a supplied video pin cable is

connected and headphones are not

connected.

IntelliBeam microphone Upper limit

Within 1 m (3.3 ft)

Center height of this

unit

Cardboard microphone

stand

Within 1 m (3.3 ft)

Listening

position

1.8 m (6.0 ft)

or more

Lower limit

Center line

IntelliBeam

microphone

Cardboard microphone stand

• “BEAM+SOUND OPTIMIZE” screen appears automatically when

the IntelliBeam microphone is connected. “BEAM OPTIMIZE

ONLY” or “SOUND OPTIMIZE ONLY” can be selected separately

in setup menu (☞p. 14).

• Data set automatically can be saved in the system memory (☞p. 16).

You can save the several data depending on listening room and you

can change the setting conveniently.

2) y

Initial settings

12 En

Using AUTO SETUP (IntelliBeam)

1

Turn the unit and your TV on.

2

Switch TV’s input to “VIDEO INPUT 1

(example)”.

3

Connect the supplied IntelliBeam

microphone to the INTELLIBEAM MIC jack.

The jack is on the underside of the main unit.

• It is normal for loud test tones to be output during the AUTO

SETUP procedure. Make sure that there are no children around

in the listening room while the AUTO SETUP procedure is in

progress.

• Make sure that your listening room is as quiet as possible. For

accurate measurement, turn off air conditioner or other devices

that make noises.

• If there are curtains in your listening room, we recommend

following the procedure below.

1 Open the curtains to improve sound reflection.

2 Run “BEAM OPTIMIZE ONLY”.

3 Close the curtains.

4 Run “SOUND OPTIMIZE ONLY”.

Note

IntelliBeam microphone

When pressing RETURN key displays the setup menu

Press SETUP key repeatedly and display the menu screen again, then

select: “AUTO SETUP”  “BEAM+SOUND OPTIMIZE”.

When the screen is not displayed

Confirm the case below.

– The input jack of your TV and the video output jack of the unit are

connected.

– The input of your TV is set to “VIDEO INPUT 1 (example)”.

“BEAM+SOUND OPTIMIZE” is selected automatically. When you

perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY”

only, refer to “AUTO SETUP via setup menu (☞p. 14)”.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started, press

RETURN key.

1) y 2) y

3) y

13 En

Initial settings

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

The screen below is displayed after connecting

IntelliBeam microphone to the unit.

1) 2)

4

Press ENTER key to start the AUTO

SETUP procedure and then leave the room

within 10 seconds.

3)

The setup screen automatically changes during the AUTO

SETUP procedure.

If AUTO SETUP procedure is complete, this unit rings

the chimes.

4)

AUTO SETUP

(PREPARATION & CHECK)

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from SoundPro-

jector. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

The best setting may not be done if you are in the room. Prepare to

leave the room in 10 seconds after pressing ENTER in step 4.

Note

MEASUREMENT COMPLETE.

BEAM MODE :5Beam/Plus2

SUBWOOFER :Yes

[ENTER]:Save set-up.

[RETURN]:Do

not save

set-up.

XXXXXXXXSHOW RESULTXXXXXXXXXX

Will begin in 10 sec.

Please leave the room.

---------

AUTO SETUP START

[RETURN]:Cancel

(After 3 min.)

5

Press ENTER key to confirm the

results.

5)

The measurement result is saved.

6

Remove the IntelliBeam microphone.

Initial screen appears.

6)

Keep the IntelliBeam microphone in a safe place.

The measurement results are stored in the internal

memory of this unit until you run the AUTO SETUP

procedure again or configure the settings manually.

You can save the several measurement result using

memory setting function (☞p. 16).

AUTO SETUP COMPLETE

Please remove the MIC

from Sound Projector

and the listening position.

• If an error occurs, an error buzzer sounds and an error message is

displayed. For details on error messages, see “Error messages for

AUTO SETUP” (☞p. 15).

• If “ENVIRONMENT CHECK:Failure” is displayed, refer to “Error

messages for AUTO SETUP” (☞p. 15), press RETURN key, and

then run the AUTO SETUP procedure again.

• Depending on the environment of your listening room, the beam

angles of front right and left and surround left and right may be set to

the same value even if “BEAM MODE :5 Beam” is displayed as a

result.

If you do not want to reflect the results, press RETURN key.

When AUTO SETUP is performed from SETUP MENU, menu selection

screen of SETUP MENU appears.

4) y 5) y

6) y

Initial settings

14 En

■ AUTO SETUP via setup menu

1

Place the IntelliBeam microphone and

press SETUP key.

2

Press U / V to select “AUTO SETUP”

and then press ENTER key.

3

Press U / V to select one of the items

below and then press ENTER key.

Select Item:

“BEAM+SOUND OPTIMIZE” (Beam optimization

and sound optimization)

It is recommended that you should select this optimization

feature, if you make settings for the first time.

This menu takes about three minutes.

“BEAM OPTIMIZE ONLY”(Beam optimization

only)

Use to optimize the beam angle so that the parameter best

matches your listening environment.

This menu takes about one minute.

“SOUND OPTIMIZE ONLY”(Sound optimization

only)

Use to optimize the beam delay, volume, and quality so

that the parameters best match your listening environment.

You must optimize the beam angle with “BEAM

OPTIMIZE ONLY” before starting “SOUND OPTIMIZE

ONLY”. It is recommended that you should select this

optimization feature in the following cases:

• If you have opened or closed the curtains in your

listening room before using this unit

• If you have manually set the beam angle.

This menu takes about two minutes.

4

Connect the IntelliBeam microphone to

this unit after “AUTO SETUP

(PREPARATION & CHECK)” screen is

displayed.

For the details on installing and connecting IntelliBeam

microphone, refer to “Installing the IntelliBeam

microphone (☞p. 11)”.

5

Perform the step 4, 5 and 6 of “Using

AUTO SETUP (IntelliBeam) (☞p. 13)”.

6

After setup is completed, remove the

IntelliBeam microphone.

The best setting may not be done if you are in the room. Prepare to

leave the room in 10 seconds after pressing ENTER in step 4.

Note

15 En

Initial settings

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

■ Error messages for AUTO SETUP

If an error message is displayed on your TV, check the error

message list to solve the problem and then follow the procedure

below.

[ERROR E-1]: Press ENTER key to run the AUTO SETUP

procedure again. Or press Z key to continue the

measurement.

[ERROR E-7]: Press key to turn this unit to standby

mode, then run AUTO SETUP procedure again after turning this

unit on.

Other errors: Press RETURN key to cancel the operation

and then run the AUTO SETUP procedure again.

If the problem is difficult to be solved, configure the settings

manually in “SETUP MENU” (☞p. 32).

ERROR E-1: Please test in quieter environment.

Cause Remedy

There is too much unwanted

noise in your listening room.

Make sure that your listening

room is as quiet as possible. You

may want to choose certain hours

during the day when there is not

much noise coming from outside.

ERROR E-2: No MIC detected. Please check MIC

connection and re-try.

Cause Remedy

The IntelliBeam microphone is

not connected to this unit or

disconnected during the AUTO

SETUP procedure.

Connect the IntelliBeam

microphone to this unit firmly.

ERROR E-3: Unexpected control is detected. Please

re-try.

Cause Remedy

Some other operations were

performed on this unit while the

AUTO SETUP procedure was in

progress.

Do not perform any other

operations while the AUTO

SETUP procedure is in progress.

ERROR E-4: Please check MIC position. MIC should

be set in front of the Sound Projector and re-try.

Cause Remedy

The IntelliBeam microphone is

not placed in front of this unit.

Make sure that the IntelliBeam

microphone is installed in front

of this unit.

ERROR E-5: Please check MIC position. MIC should

be set above 1.8m/6.0ft and re-try.

Cause Remedy

The IntelliBeam microphone is

not placed in the right distance

from this unit.

Make sure that the IntelliBeam

microphone is installed more

than 1.8 m (6.0 ft) from the front

of this unit and within 1 m (3.3

ft) from the center height of this

unit.

ERROR E-6: Volume level is lower than expected.

Please check MIC position/connection and re-try.

Cause Remedy

The IntelliBeam microphone

cannot collect the sound

produced by this unit because the

sound output level is too low.

Make sure that the IntelliBeam

microphone is firmly connected

to this unit and placed in a proper

location. If the problem persists,

contact the nearest

authorized Yamaha service

center for assistance.

ERROR E-7: Unexpected error happened. Please

turn off and re-try.

Cause Remedy

An internal system error

occurred.

Press key to turn this unit

to standby mode, then run AUTO

SETUP procedure again after

turning this unit on.

ERROR E-8: Headphones are connected. Please

unplug the headphones and re-try.

Cause Remedy

A headphone is connected. Disconnect the headphone and

re-try.

Initial settings

16 En

You can save the current beam and sound settings in the system

memory of this unit. It is handy to save certain settings according

to the varying conditions of your listening environment. For

example, if there are curtains in the path of sound beams, the

effectiveness of the sound beams will vary depending on whether

the curtains are open or closed.

■ Saving settings

Saving several measurement results

(Memory setting function)

1

Press SETUP key.

2

Select “MEMORY” and press ENTER

key.

3

Press U / V key to select “SAVE”

and then press ENTER key.

4

Press U / V key to select the desired

memory number and then press ENTER

key.

1)

Selectable item: Memory 1, Memory 2, Memory 3

“Memory 1 Save Now ?” is displayed when the memory

number is selected.

5

Press ENTER key.

“Memory 1 Saving…” is displayed and the setting is

saved.

If there are curtains in your listening room, we recommend

following the procedure below.

1. While the curtains are open, run “BEAM+SOUND

OPTIMIZE” (☞p. 14) and then save the settings to

“Memory 1”.

2. While the curtains are closed, run “SOUND OPTIMIZE

ONLY” (☞p. 14) and then save the settings to

“Memory 2”.

• If system settings are already stored in the selected memory number,

this unit overwrites the old settings.

• Memory function cannot be set when “MEMORY PROTECT” is set

to “ON” in ADVANCED SETUP (☞p. 41).

1) y

17 En

Initial settings

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

■ Loading settings

1

Press SETUP key.

2

Select “MEMORY” and press ENTER

key.

3

Press U / V key to select “LOAD”

and press ENTER key.

4

Press U / V key to select the

memory number to be loaded and then

press ENTER key.

Selectable item: Memory 1, Memory 2, Memory 3

“Memory 1 Load Now ?” is displayed when the memory

number is selected.

5

Press ENTER key.

“Memory 1 Loading…” is displayed and the setting is

loaded.

Initial settings

18 En

You can use the TV remote control to operate this unit if your TV

supports the HDMI control function (ex. REGZA Link) and is

connected to this unit’s HDMI OUT (ARC) jack.

1)

Operating the unit by TV’s remote

control

What is the HDMI control function?

Remote control of TV (Example)

Power on/off

Controls the volume

Selects a component to

reproduce sounds (this

unit or TV)

Switches input

This unit automatically

selects the input according to

the input source setting on the

TV. Switching input on TV

menu (ex. selecting Blu-ray

disc player on TV menu) also

changes input of this unit.

• Even if your TV supports the HDMI control function, some functions

may not be available. For details, refer to the manual supplied with

your TV.

• If you use HDMI to connect this unit to a device such as a Blu-ray

disc player that supports HDMI control, you can control that device

using the HDMI control function.

• We suggest that you use products (TV, Blu-ray disc/DVD player, etc.)

from the same manufacturer.

1) y

Sivu latautuu ...

Yamaha YRS-2100 Omistajan opas

Tämä käsikirja sopii myös

Yamaha YRS-2100 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat