Yamaha YRS-700 Omistajan opas

Printed in Indonesia WW77870-2

Surround sound TV stand

Meuble TV surround

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

i En

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Rear: 5 cm (2 in)

Sides: 5 cm (2 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press p to set this unit to the

standby mode, and disconnect the AC power plug from the

wall outlet.

18 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

19 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

20 Excessive sound pressure from earphones and headphones

can cause hearing loss.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by p. This state is called the standby mode. In this state, this unit

is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR U.K. CUSTOMERS

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an appropriate

3 pin plug fitted. For details, refer to the instructions described

below. Note that the plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED. Make

sure that neither core is connected to the earth terminal of the three

pin plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type.

CAUTION

Use of controls or adjustments or performance of procedures other

than those specified herein may result in hazardous radiation

exposure.

Notes

• This unit’s speakers use magnets. Do not place items that are

sensitive to magnetism, such as CRT-type TVs, clocks, credit

cards, floppy disks, etc., on top of the rack.

• When the unit is positioned close to a CRT-type TV, picture or

sound distortion may occur. In this case, move the TV away from

the unit.

1 En

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following places:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or a

stove

– places of extremely low temperatures

– dusty places

• Do not expose the remote control sensor of this unit to direct

sunlight or lighting such as inverted fluorescent lamps.

• If the batteries grow old, the effective operation range of the remote

control decreases considerably. If this happens, replace the batteries

with two new ones as soon as possible.

• Change all of the batteries if you notice the following conditions:

the operation range of the remote control decreases or the

transmission indicator does not light up or becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and color.

• Exhausted batteries may leak. If the batteries have leaked, dispose

of them immediately. Avoid touching the leaked material or letting it

come into contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

• Do not throw away batteries with general house waste. Dispose of

them correctly in accordance with your local regulations.

2 En

What you can do with this unit

To enjoy TV

To enjoy Blu-ray

movies

To enjoy games

Supplied accessories (p. 4)

Installation (p. 5)

Remote control preparation (p. 5)

Connecting your TV and Blu-ray disc player (p. 6)

Operating the unit with the TV remote control (p. 8)

Connecting a tuner

(When enjoying STB program such as on

satellite/CATV tuner)

(p. 7)

Connecting a game console

(p. 7)

Playing back TV, Blu-ray disc player, and game console (p. 10)

PREPARATION

CONNECTION/INITIAL

SETTINGS

PLAYBACK

HDMI link (HDMI control) function

p. 8

UniVolume

p. 11

Playback iPod/iPhone

p. 14

Capability for HD Audio

p. 34

Headphone surround function

p. 12

3 En

PREPARATION

CONNECTION/

INITIAL SETTINGS PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

Contents

PREPARATION

Getting started .......................................................4

Supplied accessories .................................................... 4

CONNECTION/INITIAL SETTINGS

Installation.............................................................. 5

Remote control preparation........................................... 5

Connections........................................................... 6

TV and Blu-ray disc player connection.......................... 6

Game console or tuner connection ............................... 7

Initial settings......................................................... 8

Operating the unit with the TV remote control............... 8

PLAYBACK

Playback features ................................................ 10

Basic operation for playback....................................... 10

Enjoying sound with your preference.......................... 11

Surround playback .............................................................11

Stereo playback.................................................................. 11

Playing back digitally compressed formats (MP3, WMA, etc.)

with enriched sound (Compressed Music Enhancer)..............11

Automatic volume level adjustment (UniVolume)...............11

Volume balance adjustment...............................................11

Using useful features .................................................. 12

Listening with headphones................................................. 12

Sleep timer/auto power down function ............................... 12

Settings for each input source (Option menu)....................13

Playing back iPod/iPhone ........................................... 14

When using Yamaha Universal Dock for iPod (optional

YDS-12, etc.) ....................................................................15

When using Wireless System for iPod (optional YID-

W10) ..........................................................................15

Playing back Bluetooth components........................... 16

Pairing ................................................................................16

Connecting .........................................................................17

SETTINGS

Setup menu...........................................................18

Setting procedure........................................................18

Setup menu list............................................................19

Tone control ................................................................19

Subwoofer settings......................................................19

Audio delay control......................................................19

Dynamic range control ................................................20

Volume level of each channel with test tones .............20

Input assignment.........................................................21

HDMI setup .................................................................21

HDMI control ...................................................................... 21

Audio playback component................................................ 21

Brightness of the front panel display ...........................22

Standard dimmer ............................................................... 22

Auto dimmer....................................................................... 22

Advanced setup ...................................................23

TROUBLESHOOTING

Troubleshooting...................................................24

Troubleshooting...........................................................24

ABOUT THIS UNIT

Controls and functions........................................28

Controls and functions.................................................28

Glossary................................................................31

Glossary ......................................................................31

Specifications.......................................................33

Specifications ..............................................................33

Available signal information.........................................34

About this manual

• In this manual, operations that can be performed using either the front panel buttons or the remote control are explained using the

remote control.

•

y indicates a tip for your operation.

• Notes contain important information and operating instructions.

• This manual is produced prior to production. Design and specifications are subject to change in part as a result of improvements,

etc. In case of differences between the manual and the product, the product has priority.

• The alphabet mark (such as ) indicates the remote control key(s) indicated on the figure on the left page.

4 En

PREPARATION

Getting started

Before assembly and connecting, make sure you have received all of the following items.

1)

Supplied accessories

Remote control Batteries (x 2)

(AAA, R03, UM-4)

Optical cable

(1.5 m (4.9 ft))

Video pin cable

2)

(1.5 m (4.9 ft))

Install Manual Owner’s Manual

(this manual)

Digital audio pin cable

(1.5 m (4.9 ft))

Main unit

Assembly is required before using this unit. Make sure all of the following items are included in the package, as they are all

necessary to complete assembly. Refer to the Install Manual for installation.

• Main unit • Rear panels (left and right)

• Shelf • Support posts

• Bottom panel • Center rear panel

• Glass top panel • Brackets

• Pins • Small screws M4 × 10 mm

• Large screws M5 × 30 mm • Washers

• Fasteners

Depending on the connection, you may not need all of the supplied

cables.

This cable is used when playing back iPod/iPhone video. Refer to

“Playing back iPod/iPhone (p. 14)”.

1) y 2) y

CONNECTION/INITIAL SETTINGS

5 En

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

Installation

Place the unit in the appropriate position after assembly. Refer to the supplied Install Manual for assembly. Refer to “Notes on

installation” below and place the unit correctly in the safe place.

Before installing batteries or using the remote control, make sure that you read precautions on the remote control and batteries in

“CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.”

Remote control preparation

Notes on installation

• Install your TV in accordance with the manufacturer’s instructions to prevent it from toppling over.

• This unit’s speakers use magnets. Do not place items that are sensitive to magnetism, such as clocks, credit cards, floppy disks, etc., on top of the

rack.

• When the unit is positioned close to a CRT-type TV, picture or sound distortion may occur.

Caution: Handling the tempered glass

The top glass panel is constructed of glass that has been tempered for strength and safety. In addition, a safety film has been applied to the tempered

glass to offer additional protection against injuries that may be caused by shattering glass. However, if you handle the glass inappropriately, the glass

might break and glass fragments might fly, causing injuries. Be sure to follow the precautions listed below:

• Do not allow any strong impacts to the glass (for example, do not allow thrown objects to strike the glass).

• Do not allow sharp objects to contact the glass.

• If the tempered glass has been scratched, it might break unexpectedly. If you see scratches, replace the glass immediately.

• Do not remove the glass caution sticker.

Maximum load

45kg

10kg

20kg

Interior slide sheet

An interior slide sheet is attached to the bottom of the unit,

allowing you to move the unit into position easily. To

prevent damage to the floor, clean the floor of dust and

rubbish before moving the unit.

Installing the batteries

1

3

2

Operation range

Within 6 m (20 ft)

6 En

Connections

For the cable connection, follow the orders below.

TV and Blu-ray disc player connection

1

HDMI cable (optional)

Input the digital audio/video signals

of the Blu-ray disc player to this unit.

2

HDMI cable (optional)

The digital video of the Blu-ray disc

is reflected on TV.

3

Optical cable (supplied)

Play back digital sounds of TV on

this unit.

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or terminal.

123

INPUT1

INPUT2

HDMI INPUT

HDMI

OUTPUT

AUDIO VIDEORL

OPTICAL

OUTPUT

To AC wall outlet

Blu-ray disc player

1. Remove the cap

2. Check the direction of

the plug

TV

Video signals

Audio signals

1

2

3

(Example)

1)

2)

Audio return channel (ARC) supported TV

• Connect HDMI cable to audio return channel supported terminal (the

terminal with “ARC” indicated) on TV. In this case, you do not need

to connect optical cable.

• Activate the HDMI control function of this unit (☞p. 21).

What is audio return channel (ARC)?

A function transmits digital audio signal output from TV to this unit

through a HDMI cable. By this function, a digital audio pin cable to

connect TV and this unit is not needed.

Depending on the setting, HDMI for video signal, optical or coaxial

digital audio or analog audio for audio signal can be selected. Refer to

“Input assignment (☞p. 21)”.

1) y

2) y

7 En

Connections

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

Game console or tuner connection

Additional external device (example) Connecting cable

1 HDMI supported game console

HDMI cable (optional)

2 Satellite/cable TV (HDMI supported)

HDMI cable (optional)

3 Satellite/cable TV (HDMI not supported)

Digital audio pin cable (supplied)

4)

4 HDMI not supported game console

Analog audio stereo pin cable (optional)

4)

HDMI

OUTPUT

HDMI

OUTPUT

ANALOG

OUTPUT

COAXIAL

OUTPUT

VIDEO

INPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

Video signals

Audio signals

TV

1 2 3 4

3)

(Example)

4)

To AC wall outlet

(Example)

4)

The additional devices having an optical digital output jack, connect to

the optical digital input jack of this unit with an optical cable.

To connect a game console or tuner to TV, you need extra video pin

cables (optional).

3) y 4) y

8 En

Initial settings

■ What is the HDMI control function?

You can use the TV remote control to operate this unit if your TV

supports the HDMI control function (ex. REGZA Link) and is

connected to this unit’s HDMI OUT (ARC) jack.

1)

Operating the unit with the TV

remote control

Remote control of TV (Example)

Power on/off

Controls the volume

Selects a component to

reproduce sounds (this

unit or TV)

Switches input

This unit automatically

selects the input according

to the input source setting

on the TV. Switching input

on TV menu (ex. selecting

Blu-ray disc player on TV

menu) also changes input

of this unit.

• Even if your TV supports the HDMI control function, some functions

may not be available. For details, refer to the manual supplied with

your TV.

• If you use HDMI to connect this unit to a device such as a Blu-ray

disc player that supports HDMI control, you can control that device

using the HDMI control function.

• We suggest that you use products (TV, Blu-ray disc/DVD player, etc.)

from the same manufacturer.

1) y

9 En

Initial settings

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT English

CONNECTION/

INITIAL SETTINGS

When the connected components and jacks are changed, reset this

unit with following procedures.

Setting the HDMI control function

1

Turn on all components connected to this

unit with HDMI.

2

Check all components connected with

HDMI and enable the HDMI control

function on each component.

For this unit, set “HDMI Ctrl” to “On” (☞p. 21).

2)

For external components, refer to the manual supplied

with each component.

3)

3

Turn off the TV and then turn on it again.

Registering HDMI components to TV

4)

1

Select this unit as the input source for the

TV.

2

Turn on the HDMI control function

supported component (example: Blu-ray

disc player) connected to this unit.

3

Select the input source of this unit to Blu-

ray disc player and check whether the

image in the player is correctly displayed

or not.

When connecting Blu-ray disc player with HDMI 1 jack,

press input selector key once to show the following

diagram.

HDMI1

Input source name

4

Check if the HDMI control function works

(turn on this unit or adjust the volume level

using the remote control of the TV).

If the HDMI control function is not working

Check the following:

– The TV is connected to the HDMI OUT (ARC) jack of this

unit.

–“HDMI Ctrl” (☞p. 21) is set to “On” in setup menu.

– The HDMI control function is enabled on the TV. (Also

check the relative settings such as power interlock function

or speaker priority.)

The HDMI control function is not working even checking the

above,

– Turn off this unit and the TV, and then turn them back on

again.

– Unplug the power cables of the TV and this unit, and plug

them in again.

– After selecting INPUT1, INPUT2, INPUT3 or DOCK,

change the input of TV and the one of this unit to the same

input.

Changing the connection method and

connected components

1

Turn off the HDMI control function of the

TV and player, turn off all connected

devices, and change the connections.

2

Perform the step 1 to 3 of “Setting the

HDMI control function” (☞p. 9).

• The default setting is “Off”.

When “HDMI Ctrl” is set to “On” in setup menu,

– Even you press key, the power does not completely turned

off and the signal outputs from the HDMI IN jack to HDMI OUT

(ARC) jack.

– Before pressing key, select desired input sources connected

to HDMI IN (1 to 3).

– According to the TV, the TV operation such as changing the

channel may change the setting of surround modes of this unit.

The example of TV settings

• From a setup menu on your TV, select “Link setting”  “HDMI

control setting” (example), then set a setting such as “HDMI control

function” to “On” (example).

• Setting such as “Speaker priority” should be set to “AV amplifier”.

For some HDMI components, you only need to set the HDMI control

function. Registering HDMI components to TV is not required in this

case.

2) y 3) y

4) y

10 En

PLAYBACK

Playback features

Basic operation for playback

1

Press key to turn on this unit.

2

Turn on components (TV, Blu-ray disc

player, etc.) connected to this unit.

3

Select a component you want to listen to

by pressing the input selector key ( , ,

) corresponding to the connection of

external components.

For example, when playing back a Blu-ray disc player

connected to HDMI IN 1 jack, select HDMI1 by pressing

input selector key as shown below.

4

Play back component selected in step 3.

5

Press VOLUME +/- key to adjust the

volume.

1)

2) 3)

6

Select surround mode or stereo mode and

set your sound preferences. (☞p. 11)

HDMI1

Input source name

Press key to turn this unit to standby mode.

When audio is output from both TV speaker and this unit, mute the TV

sound.

To mute the sound

Press MUTE key. While the mute function is activated, the VOL

indicator on the front panel display flashes. To resume the volume, press

MUTE key again or press VOLUME +/- key.

When sound input to HDMI IN is output from the TV, the volume level

does not change even if you press VOLUME +/- key or MUTE

key.

1) y

2) y

3) Note

11 En

Playback features

PREPARATION

CONNECTION/

INITIAL SETTINGS SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT EnglishPLAYBACK

Playback surround sounds using Yamaha’s exclusive AIR

SURROUND XTREME.

An extended sound is achieved for a 2 channel source.

Play back digitally compressed format such as MP3 and WMA

emphasizing bass and treble extended dynamically.

While watching the TV, compensate the excessive volume differences

to make it easier to hear during the following cases.

• When switching the channel

• When a TV program changed to commercial

• When one program is finished and another program started

Use this feature to adjust the volume balance for each channel

during playback.

7)

Enjoying sound with your

preference

Surround playback

1

Press SURROUND key to switch to

surround mode.

2

Press one of the surround mode keys ( ).

4)

MOVIE: For movies

MUSIC: For music

SPORTS: For sports and news

GAME: For video games

Stereo playback

Press STEREO key to switch to stereo

mode.

Each time you press STEREO key, the function is turned on

(Extended Stereo) and off (Stereo) alternately.

Stereo: Reproduces the stereo sound without any effect.

Extended Stereo: Reproduces a wider stereo sound image.

Playing back digitally compressed formats

(MP3, WMA, etc.) with enriched sound

(Compressed Music Enhancer)

Press ENHANCER key to turn the function

on/off.

5)

Automatic volume level adjustment

(UniVolume)

Press UNIVOLUME key to turn the function

on/off.

6)

Volume balance adjustment

1

Press LEVEL key.

2

Press U/ V key to select adjustable

channel from the followings.

CenterLv: Center

SurLR Lv: Surround left/right

SWFR Lv: Subwoofer

3

Press Y/Z key to adjust the volume.

8)

Adjustable range: -10.0 dB to +10.0 dB

4

Press LEVEL key to exit from the menu.

This unit automatically memorizes the settings assigned to each input

source. When you select another input, the unit automatically recalls the

last settings for the selected input.

• The default setting is “On” for DOCK input, and “Off” for other

inputs.

• Compressed Music Enhancer does not work when the source is

following digital audio signal,

– Dolby TrueHD, DTS-HD Master Audio, etc.

– Signal that sampling rate is more than 48 kHz.

• The default setting is “Off”.

• To set the UniVolume to “Off”, press UNIVOLUME key.

• We recommend turning off the UniVolume function during playback

of music.

Refer to “Volume level of each channel with test tones (☞p. 20)” when

adjusting the test sound.

Example of volume balance

• If you have problems hearing words: Select CenterLv (center) to

increase the level.

• When the sound does not seem like surround sound: Select SurLR Lv

(Surround) to increase the level.

• The volume of subwoofer also can be adjusted by using

SUBWOOFER +/- key.

4) y

5) y

6) y

7) y

8) y

Playback features

12 En

Use this feature to automatically set this unit to the standby mode

after a specified period of time.

■ Auto power down function

3)

When AutoPowerDown is set, the unit is turned to standby mode

automatically after 10 minutes from the selected input source is

turned off or in standby mode. This function is useful to prevent

you from forgetting to turn off the unit.

Using useful features

Listening with headphones

Insert a headphone plug to the PHONES jack

(☞p. 28) of this unit.

1)

Sleep timer/auto power down function

Press SLEEP key repeatedly.

Switching the time it takes to switch to standby mode. The

SLEEP indicator (☞p. 29) flashes in the front panel display.

The SLEEP indicator in the front panel display lights up and the

sleep timer is set.

2)

Selectable item: Sleep 120 min., Sleep 90 min., Sleep

60 min., Sleep 30 min., AutoPowerDown, Off

The surround sound using headphones

With newly-developed 7.1 ch headphone surround

technology, you can enjoy surround and stereo sound using

a headphone same as speaker. (☞p. 11)

• The headphone volume, tone control, and LFE level can be set

separately with speaker setting.

• If too much bass is heard while playing back 5.1 or 7.1 channels

containing LFE channel (0.1ch), it may be improved by decreasing

the LFE level. (☞p. 19)

• The sleep timer setting is canceled if this unit is set to the standby

mode or “Off” is selected.

• When AutoPowerDown is set, SLEEP indicator does not light up

during playback.

• If the unit is operated during the 10 minutes before entering standby

mode, the unit does not enter standby mode until 10 minutes after the

latest operation.

• AutoPowerDown cannot be selected when:

– AUDIO INPUT (INPUT3) or DOCK is selected.

– HDMI1-3 is selected and HDMI control function is on.

1) y

2) y

3) y

13 En

Playback features

PREPARATION

CONNECTION/

INITIAL SETTINGS SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT EnglishPLAYBACK

Set according to each input (TV/HDMI1-3/INPUT1-3/DOCK).

Available menu items vary depending on the selected input.

Option menu items

The following menu items are provided for each input.

The option menu items are listed below. These settings are

applied to the currently selected input source. The default settings

are marked with “*”.

■ Adjusting input level of each jack

(Volume Trim)

Adjust the input level for each jack to compensate for variations

in volume between different input devices.

Adjustable range: -6.0 dB to 0.0 dB* to +6.0 dB

■ Switching the audio signal to play back

(Decoder Mode)

Select digital audio signals for playback.

Selectable item: Auto*, DTS

Auto: This unit automatically selects the audio signal for

playback. Normally select this mode.

DTS: This unit plays back only DTS signal.

■ Displaying the input signal information

(Signal Info)

Press U/ V to change the following informations.

Settings for each input source (Option menu)

1

Press input key ( , , , ) to select

the input you want to change the setting.

2

Press OPTION key.

The option menu is displayed on the front panel display.

3

Select the items by pressing U/ V

key, then press ENTER key.

4

Change setting value by pressing Y/Z

key.

5

To exit the option menu, press OPTION

key.

Input source Menu items

HDMI1-3 Volume Trim, Decoder Mode, Signal Info

TV

INPUT1-3

DOCK

Volume Trim, Connect, Disconnect, Pairing,

Interlock

4)

; Volume Trim

Format Digital audio format

Channel The number of channels included in input signal

(front/surround/LFE (low frequency sound

effects))

Display example: [3/2/0.1]  Front 3ch,

Surround 2ch, LFE for input signal

5)

Sampling Sampling frequency for digital input signal

Bitrate Bitrate per second of input signal

HDMI In HDMI video signal resolution

HDMI Message When error occurs with HDMI (displayed only

when error is occurred.)

For details, on Interlock, refer to “Playing back iPod/iPhone (☞p. 14)”.

For details on Connect, Disconnect and Pairing, refer to “Playing back

Bluetooth components (☞p. 16)”.

If the input signal includes channels that cannot be displayed in the

format shown in the display example, the total number of channels will

be displayed, as in “5.1ch”.

4) y

5) y

Playback features

14 En

You can play music stored in iPod/iPhone connected to Yamaha

Universal Dock for iPod (optional YDS-12, etc.) or Wireless

System for iPod/iPhone (optional YID-W10).

• Connect when this unit is in standby mode.

• For details on how to connect and set up the YDS-12 and YID-W10,

refer to manuals supplied with them.

When using YDS-12, YDS-11, or YDS-10 with the video pin cable

(supplied) to connect the VIDEO OUT jack of this unit to the VIDEO

INPUT jack of the TV, you can display iPod/iPhone video on the TV.

• Some features may not be available depending on the model or the

software version of your iPod/iPhone.

• For details about the messages displayed on the front panel display of

connected iPod/iPhone, refer to “iPod/iPhone (☞p. 26)” in

“Troubleshooting”.

• Be sure to set the volume to minimum before docking or removing

your iPod/iPhone.

• To set the playback volume higher than the maximum volume of the

iPod/iPhone, use this unit’s remote control to control the volume.

1) y

2) y

3) Note

Playing back iPod/iPhone

1

Insert the iPod/iPhone into the Yamaha

Universal Dock for iPod or Wireless

System for iPod/iPhone connected to the

DOCK terminal.

1)

Place it as far as possible from this unit to avoid the noise.

2

Playback iPod/iPhone by selecting dock

input by pressing DOCK key.

3)

To VIDEO INPUT of TV

2)

(only when YDS-12/YDS-11/

YDS-10 is used)

YDS-12, etc.

15 En

Playback features

PREPARATION

CONNECTION/

INITIAL SETTINGS SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT EnglishPLAYBACK

After setting the iPod/iPhone to the dock, you can use the remote

control of this unit for playback operations. You can also display

iPod/iPhone video on the TV.

: Controls iPod’s menu.

: Controls click wheel.

iPod/iPhone supported by Universal Dock for iPod

(YDS-12/YDS-11/YDS-10):

(As of September 2010)

• iPod touch, iPod mini, iPod (4th and 5th generations), iPod

Classic, iPod nano, iPhone, iPhone 3G, iPhone 3GS

• iPhones are not compatible with YDS-11/YDS-10.

After connecting the receiver to this unit and setting the iPod/

iPhone to the transmitter, you can use the connected iPod/iPhone

as a remote control while playing back music.

iPod/iPhone supported by Wireless System for iPod

(YID-W10):

(As of September 2010)

iPod touch, iPod (5th generation), iPod Classic, iPod nano,

iPhone, iPhone 3G, iPhone 3GS

■ Link with this unit (Interlock mode)

6)

When using YID-W10, You can use functions following for iPod/

iPhone when “Interlock” is set to “On” in option menu (☞p. 13).

• When playback starts on iPod/iPhone, this unit is turned on and

DOCK (iPod) is selected as source automatically.

• This unit turns to standby mode automatically when the

playback is stopped or after a while iPod/iPhone is removed

from the transmitter.

When using Yamaha Universal Dock for iPod

(optional YDS-12, etc.)

When using Wireless System for iPod

(optional YID-W10)

4)

5)

This unit charges the battery of an iPod/iPhone stationed in the Yamaha

Universal Dock for iPod connected to the DOCK terminal even when

this unit is in standby mode. “Charging” appears in the front panel

display.

When YID-W10 is connected, and the “Interlock” is set to “On”, it

charges even in standby mode.

This function works with ring tone and sound of application. When the

iPhone is set to silent mode, this unit does not turn on with the ring tone.

4) y

5) y

6) y

Playback features

16 En

Playback music stored in the Bluetooth components (portable

audio players, Bluetooth-enabled computers, etc.) connected to

the Bluetooth Wireless Audio Receiver.

For details, refer to the manual supplied with YBA-10.

Refer to the manual of your Bluetooth component for details.

To cancel pairing, press RETURN key.

1) y

2) y

3) y

Playing back Bluetooth

components

Pairing

1

As described in step 1 (☞p. 14) of “Playing

back iPod/iPhone”, connect the Bluetooth

Wireless Audio Receiver (optional YBA-10)

to DOCK terminal.

1)

2

Press DOCK key to set the input to

DOCK.

3

Turn on the Bluetooth component you

want to pair with, and then enter pairing

state.

2)

4

Press OPTION key.

Option menu for DOCK input appears in the display.

5

Select “Pairing” by pressing U/ V

key and press ENTER key.

3)

“Searching...” appears on the display when the Bluetooth

connection is initiated.

About “Pairing”

It is the operation of registering a component for

communications. Pairing must be performed before using a

Bluetooth component with the Yamaha Bluetooth Wireless

Audio Receiver connected to the system for the first time,

or if the registered pairing data has been deleted.

To ensure security, a time limit of 8 minutes is set for the

pairing operation. Please read and fully understand all the

instructions before starting.

17 En

Playback features

PREPARATION

CONNECTION/

INITIAL SETTINGS SETTINGS

TROUBLESHOOTING

ABOUT THIS UNIT EnglishPLAYBACK

6

Check that the Bluetooth components

recognize the Bluetooth Wireless Audio

Receiver.

If the Bluetooth component detects the Yamaha Bluetooth

Wireless Audio Receiver, the audio receiver name

(“YBA-10 YAMAHA”, for example) appears in the

device list of the Bluetooth component.

7

Select the Bluetooth Wireless Audio

Receiver from the component list of the

Bluetooth components and input “0000”

for password of the Bluetooth.

Connecting

1

Press DOCK key to set the input to

DOCK.

2

Press OPTION key.

3

Select “Connect” and press ENTER

key.

5)

4

To disconnect the Bluetooth Wireless

Audio Receiver from the Bluetooth

component, press again to display

option menu, select “Disconnect”, and

press ENTER key.

4)

When establishing the Bluetooth connection from this unit, it is only

possible to connect to the most recently connected Bluetooth component.

• For details of messages, refer to “Bluetooth (☞p. 27)” in

“Troubleshooting”.

• If you want to establish a connection with a Bluetooth other than the

one most recently connected, initiate the connection from that

Bluetooth component. Refer to the manual of your Bluetooth

component for details.

4) y

5) y

18 En

SETTINGS

Setup menu

Setting procedure

1

Press SETUP key to enter the setup

menu.

“Sound Setup” appears on the front panel display.

2

Select menu by pressing U/ V key

and press ENTER key.

Repeat this procedure until desired menu appears on the

front panel display.

3

Change setting value of each menu by

pressing Y/Z key.

1)

4

Press SETUP key again to exit the

setup menu.

2)

The default settings are marked with “*”.

Press RETURN key to return to the previous menu.

1) y

2) y

Sivu latautuu ...

Yamaha YRS-700 Omistajan opas

Yamaha YRS-700 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat