Yamaha YRS-1100 Omistajan opas

Kategoria
Receiver
Tyyppi
Omistajan opas

Tämä käsikirja sopii myös

Printed in Indonesia WW75150-1
Surround sound TV stand
Meuble TV surround
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place –
away from direct sunlight, heat sources, vibration, dust,
moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Rear: 5 cm (2 in)
Sides: 5 cm (2 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and
may cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a lightning
storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press p to set this unit to the
standby mode, and disconnect the AC power plug from the
wall outlet.
18 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like. When you dispose of batteries,
follow your regional regulations.
20 Excessive sound pressure from earphones and headphones
can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by p. This state is called the standby mode. In this state, this unit
is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR U.K. CUSTOMERS
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an appropriate
3 pin plug fitted. For details, refer to the instructions described
below. Note that the plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED. Make
sure that neither core is connected to the earth terminal of the three
pin plug.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
Notes
This unit’s speakers use magnets. Do not place items that are
sensitive to magnetism, such as CRT-type TVs, clocks, credit
cards, floppy disks, etc., on top of the rack.
When the unit is positioned close to a CRT-type TV, picture or
sound distortion may occur. In this case, move the TV away from
the unit.
i En
1 En
Notes on remote controls and batteries
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following places:
places of high humidity, such as near a bath
places of high temperatures, such as near a heater or a
stove
places of extremely low temperatures
dusty places
Do not expose the remote control sensor of this unit to direct
sunlight or lighting such as inverted fluorescent lamps.
If the batteries grow old, the effective operation range of the remote
control decreases considerably. If this happens, replace the batteries
with two new ones as soon as possible.
Change all of the batteries if you notice the following conditions:
the operation range of the remote control decreases or the
transmission indicator does not light up or becomes dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and color.
Exhausted batteries may leak. If the batteries have leaked, dispose
of them immediately. Avoid touching the leaked material or letting it
come into contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
Do not throw away batteries with general house waste. Dispose of
them correctly in accordance with your local regulations.
2 En
What you can do with this unit
To enjoy TV
To enjoy Blu-ray
movies
To enjoy games
Checking supplied accessories (p. 4)
Installation (p. 5)
Preparing the remote control (p. 7)
Connecting your TV and Blu-ray disc player (p. 8)
Operating the unit by TV’s remote control (p. 18)
When enjoying STB program
such as on satellite/CATV tuner
(p. 9)
Connecting a game
console (p. 9)
Playing back a TV, Blu-ray disc player, and game console (p. 20)
PREPARATION
CONNECTION/
INITIAL SETTINGS
PLAYBACK
Setting the best possible sound automatically (p. 11)
HDMI link (HDMI control)
function
p. 18
Cinema DSP function
p. 22
IntelliBeam function
p. 11
Headphone surround function
p. 26
UniVolume
p. 21
Playing back iPod/iPhone
p. 29
3 En
PREPARATION
CONNECTION/
INITIAL SETTINGS PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
Contents
PREPARATION
Getting started .......................................................4
Supplied accessories .................................................... 4
CONNECTION/INITIAL SETTINGS
Installation..............................................................5
Remote control preparation........................................... 7
Connections...........................................................8
TV and Blu-ray disc player connection.......................... 8
Game console or tuner connection ............................... 9
Initial settings.......................................................10
Selecting language for menu display .......................... 10
Auto setup for appropriate surround effects
(IntelliBeam)........................................................... 11
Operating the unit by TV’s remote control................... 18
PLAYBACK
Playback features ................................................ 20
Basic operation for playback....................................... 20
Enjoying sound with your preference.......................... 21
Switching stereo/surround sound....................................... 21
Playing back digitally compressed formats (MP3, WMA, etc.)
with enriched sound (Compressed Music Enhancer)......... 21
Automatic volume level adjustment (UniVolume)............... 21
Volume balance adjustment...............................................21
Enjoying realistic surround sound (CINEMA DSP).............22
Changing the audio output method for surround playback........23
Surround decoder setting................................................... 25
Using useful features .................................................. 26
Listening with headphones................................................. 26
Sleep timer/auto power down function ............................... 27
Settings for each input source (Option menu)....................27
Playing back iPod/iPhone ........................................... 29
When using Yamaha Universal Dock for iPod (optional
YDS-12, etc.) ....................................................................29
When using Wireless System for iPod (optional YID-W10).......29
Playing back Bluetooth components........................... 30
Pairing ................................................................................30
Connecting ......................................................................... 31
SETTINGS
Setup menu...........................................................32
Setting procedure........................................................32
Setup menu list............................................................33
Manual setup...............................................................34
Setting parameters ........................................................... 34
Beam adjustment.............................................................. 35
Image location .................................................................. 36
Tone control ................................................................36
Tone control...................................................................... 36
Subwoofer settings ........................................................... 36
Audio delay control ........................................................... 36
Dynamic range control...................................................... 37
Volume level of each channel with test tones ................... 37
Sound out setting ........................................................37
Sound beam output configuration ..................................... 37
Input assignment.........................................................38
Input assignment .............................................................. 38
Input rename..................................................................... 39
HDMI setup....................................................................... 39
DISPLAY MENU ............................................................... 40
Advanced setup ...................................................41
TROUBLESHOOTING
Troubleshooting...................................................42
ABOUT THIS UNIT
Controls and functions........................................46
Glossary................................................................49
Specifications.......................................................51
Using the supplied demonstration DVD.............53
Index......................................................................54
About this manual
In this manual, operations that can be performed using either the front panel buttons or the remote control are explained using the
remote control.
y indicates a tip for your operation.
Notes contain important information and operating instructions.
This manual is produced prior to production. Design and specifications are subject to change in part as a result of improvements,
etc. In case of differences between the manual and the product, the product has priority.
The alphabet mark (such as ) indicates the remote control key(s) indicated on the figure on the left page.
4 En
PREPARATION
Getting started
Before assembly and connecting, make sure you have received all of the following items.
1)
Supplied accessories
Remote control Battery (× 2)
(AA, R6, UM-3)
Optical cable
(1.5 m (4.9 ft))
Video pin cable
(for displaying menu
and iPod video)
(1.5 m (4.9 ft))
Install Manual
Owner’s Manual
(this manual)
Main unit
IntelliBeam microphone
(× 1) (6 m (19.7 ft))
Cardboard microphone
stand (× 1)
Quick Reference Guide
Digital audio pin cable
(1.5 m (4.9 ft))
Demonstration DVD
(p. 53)
Assembly is required before using this unit. Make sure all of the following items are included in the package, as they are all
necessary to complete assembly. Refer to the Install Manual for installation.
Main unit Rear panels (left and right)
Shelf Support posts
Bottom panel Center rear panel
Glass top panel Brackets
Pins Small screws M4 × 10 mm
Large screws M5 × 30 mm Washers
Fasteners
According to the connection, the supplied cables may not be needed.
1) y
5 En
CONNECTION/INITIAL SETTINGS
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
Installation
Place the unit in the appropriate position after assembly. Refer to the supplied Install Manual for assembly. This section describes a
suitable installation location to install this unit. Refer to “Notes on installation” below and place the unit correctly in the safe place.
This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround sound effects
produced by this unit may not be sufficient when this unit is installed in the following locations.
Rooms with walls inadequate for reflecting sound beams
Rooms with acoustically absorbent walls
Rooms with measurements outside the following range: W (3 to 7 m (10 to 23 ft)) × H (2 to 3.5 m (7 to 11.5 ft)) × D (3 to 7 m (10 to
23 ft))
Rooms with less than 1.8 m (6 ft) from the listening position to this unit
Rooms where objects such as furniture are likely to obstruct the path of sound beams
Rooms where the listening position is close to the walls
Rooms where the listening position is not in front of this unit
My Surround
In the room such as above, you can enjoy rich surround effects by My Surround (p. 24).
Before installing this unit
Notes on installation
Install your TV in accordance with the manufacturer’s instructions to prevent it from toppling over.
This unit’s speakers use magnets. Do not place items that are sensitive to magnetism, such as clocks, credit cards, floppy disks, etc., on top of the
rack.
When the unit is positioned close to a CRT-type TV, picture or sound distortion may occur.
Caution: Handling the tempered glass
The top glass panel is constructed of glass that has been tempered for strength and safety. In addition, a safety film has been applied to the tempered
glass to offer additional protection against injuries that may be caused by shattering glass. However, if you handle the glass inappropriately, the glass
might break and glass fragments might fly, causing injuries. Be sure to follow the precautions listed below:
Do not allow any strong impacts to the glass (for example, do not allow thrown objects to strike the glass).
Do not allow sharp objects to contact the glass.
If the tempered glass has been scratched, it might break unexpectedly. If you see scratches, replace the glass immediately.
Do not remove the glass caution sticker.
Maximum
load
50kg
15kg
30kg
Interior slide sheet
An interior slide sheet is attached to the
bottom of the unit, allowing you to
move the unit into position easily. To
prevent damage to the floor, clean the
floor of dust and rubbish before moving
the unit.
YRS-2100
YRS-1100
Install this unit in the center of the left and right walls.
Listening position (such as sofa, etc.) should be located at the
front of the unit.
The distance between listening position and the unit should be
more than 1.8 m (6 ft).
YRS-1100
Maximum load
80kg
10kg each
(Left, center
and right)
40kg
YRS-2100
Installation
6 En
This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture
obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the corner.
Installation examples
Parallel installation
Install this unit as close to the exact center of the wall as possible.
Ideal installation condition
Install this unit as close to the exact front of your normal listening position as possible.
The distance between listening position and the unit should be more than 1.8 m (6 ft).
Installing this unit
Parallel installation
Install this unit in the exact center of the wall when it is measured
from the left and right corners
Corner installation
Install this unit in the corner at a 40° to 50° angle from the
adjacent walls.
An object, such as furniture
40° to 50°
Parallel installation
(with 5Beam)
Corner installation
(with Stereo+3Beam)
Installation
7 En
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
Installing in a non-square room
Install this unit so that the sound beams can be reflected off the walls.
Before installing batteries or using the remote control, make sure that you read precautions on the remote control and batteries in
“CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.”
Remote control preparation
Installing the batteries
Battery × 2
(AA, R6, UM-3)
Press U
Remove the transparent sheet before using.
Operation range
Within 6 m (20 ft)
8 En
Connections
For the cable connection, follow the orders below.
TV and Blu-ray disc player connection
1
HDMI cable
(optional)
Input the digital audio/
video signals of the Blu-
ray disc player to this
unit.
2
HDMI cable
(optional)
The digital video of the
Blu-ray disc is reflected
on TV.
3
Optical cable
(supplied)
Play back digital sounds
of TV on this unit.
4
Video pin cable
(supplied)
To display the YRS-
2100/YRS-1100’s setup
menus on the TV.
Do not connect the power cable until all connections are completed.
Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or terminal.
123
INPUT1
INPUT2
HDMI INPUT
OPTICAL
OUTPUT
VIDEO
AUDIORL
HDMI
OUTPUT
To AC wall outlet
Blu-ray disc player
1. Remove the cap
2. Check the direction of
the plug
TV
Video signals
Audio signals
1
2
3
(Example)
1)
4
2)
Audio return channel (ARC) supported TV
Connect HDMI cable to audio return channel supported terminal (the
terminal with “ARC” indicated) on TV. In this case, you do not need
to connect optical cable.
Activate the HDMI control function of this unit (p. 39).
What is audio return channel (ARC)?
A function transmits digital audio signal output from TV to this unit
through a HDMI cable. By this function, a digital audio pin cable to
connect TV and this unit is not needed.
Depending on the setting, HDMI for video signal and optical digital
audio, coaxial digital audio or analog audio for audio signal can be
selected. Refer to “Input assignment (p. 38)”.
1) y
2) y
Connections
9 En
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
Game console or tuner connection
Additional external device (example) Connecting cable
1 HDMI supported game console
HDMI cable (optional)
2 Satellite/cable TV (HDMI supported)
HDMI cable (optional)
3 Satellite/cable TV (HDMI not supported)
Digital audio pin cable (supplied)
4)
4 HDMI not supported game console
Analog audio stereo pin cable (optional)
4)
HDMI
OUTPUT
HDMI
OUTPUT
ANALOG
OUTPUT
COAXIAL
OUTPUT
VIDEO
INPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
VIDEO
INPUT
Video signals
Audio signals
TV
1 2 3 4
3)
(Example)
4)
To AC wall outlet
(Example)
4)
(Example)
(Example)
The additional devices having an optical digital output jack, connect to
the optical digital input jack of this unit with an optical cable.
To connect a game console or tuner to TV, you need extra video pin
cables (optional).
3) y 4) y
10 En
Initial settings
Selecting language for menu
display
1
Turn the unit and your TV on.
2
Switch TV’s input to “VIDEO INPUT 1
(example)”.
Check whether the initial screen is displayed.
1)
3
Press and hold SETUP key until the
“LANGUAGE SETUP” menu appears on
your TV.
4
Press U / V key to select the desired
language and then press ENTER key.
Selectable item: ENGLISH, DEUTSCH, FRANÇAIS,
ESPAÑOL, ITALIANO, NEDERLANDS, РУССКИЙ,
SVENSKA
Initial setting: English
YRS-
2100
Push [SETUP] to
begin SETUP MENU.
(example)
[ ]/[ ]:Sel [ENTER]:Return
3)LANGUAGE SETUP
When the screen is not displayed
Confirm the case followings.
The input jack of your TV and the video output jack of the unit are
connected.
The input of your TV is set to “VIDEO INPUT 1 (example)”.
1) y
11 En
Initial settings
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
This unit creates a sound field by reflecting sound beams on the
walls of your listening room and by broadening the cohesion of
all the channels. Just as you would arrange the speaker position of
other audio systems, you need to set the beam angle to enjoy the
best possible sound from this unit.
This unit employs the beam optimization and sound optimization
features with the aid of the supplied IntelliBeam microphone, allowing
you to avoid troublesome listening-based setup and achieving highly
accurate sound adjustments that best match your listening
environment. We call these two features “IntelliBeam” generically.
Beam optimization:
This feature optimizes the beam angle so that the parameter best
matches your listening environment.
Sound optimization:
This feature optimizes the beam delay, volume, and quality so
that the parameters best match your listening environment.
This unit performs these two automatic optimizations with the aid
of the supplied IntelliBeam microphone.
2)
Follow the procedure below to connect the IntelliBeam
microphone to this unit and place it in a proper location.
Auto setup for appropriate
surround effects (IntelliBeam)
Installing the IntelliBeam microphone
1
Place the IntelliBeam microphone on a flat
level surface at your normal listening position.
Use the supplied cardboard microphone stand or a tripod
to place the IntelliBeam microphone at the same height as
your ears would be when you are seated.
Assembling the supplied cardboard
microphone stand
The AUTO SETUP procedure may not be run successfully if this
unit is installed in one of the rooms described in “Installing this
unit” on page 6. In such cases, run MANUAL SETUP (p. 14) to
manually adjust the corresponding parameters.
Do not connect the IntelliBeam microphone to an extension cable
as doing so may result in an inaccurate sound optimization.
After you have completed the AUTO SETUP procedure, be sure
to disconnect the IntelliBeam microphone.
The IntelliBeam microphone is sensitive to heat.
Keep the IntelliBeam microphone away from direct sunlight.
Do not place the IntelliBeam microphone on top of this unit.
Note
1 2 3
54
Remove
Fit in
Run
through
Place
horizontally
Fit in
Make sure that there are no obstacles between the
IntelliBeam microphone and the walls in your listening
room as these objects obstruct the path of sound beams.
However, any objects that are in contact with the walls
will be regarded as a protruding part of the walls.
2
Check if a supplied video pin cable is
connected and headphones are not
connected.
IntelliBeam microphone Upper limit
Within 1 m (3.3 ft)
Center height of this
unit
Cardboard microphone
stand
Within 1 m (3.3 ft)
Listening
position
1.8 m (6.0 ft)
or more
Lower limit
Center line
IntelliBeam
microphone
Cardboard microphone stand
“BEAM+SOUND OPTIMIZE” screen appears automatically when
the IntelliBeam microphone is connected. “BEAM OPTIMIZE
ONLY” or “SOUND OPTIMIZE ONLY” can be selected separately
in setup menu (p. 14).
Data set automatically can be saved in the system memory (p. 16).
You can save the several data depending on listening room and you
can change the setting conveniently.
2) y
Initial settings
12 En
Using AUTO SETUP (IntelliBeam)
1
Turn the unit and your TV on.
2
Switch TV’s input to “VIDEO INPUT 1
(example)”.
3
Connect the supplied IntelliBeam
microphone to the INTELLIBEAM MIC jack.
The jack is on the underside of the main unit.
It is normal for loud test tones to be output during the AUTO
SETUP procedure. Make sure that there are no children around
in the listening room while the AUTO SETUP procedure is in
progress.
Make sure that your listening room is as quiet as possible. For
accurate measurement, turn off air conditioner or other devices
that make noises.
If there are curtains in your listening room, we recommend
following the procedure below.
1 Open the curtains to improve sound reflection.
2 Run “BEAM OPTIMIZE ONLY”.
3 Close the curtains.
4 Run “SOUND OPTIMIZE ONLY”.
Note
IntelliBeam microphone
When pressing RETURN key displays the setup menu
Press SETUP key repeatedly and display the menu screen again, then
select: “AUTO SETUP” “BEAM+SOUND OPTIMIZE”.
When the screen is not displayed
Confirm the case below.
The input jack of your TV and the video output jack of the unit are
connected.
The input of your TV is set to “VIDEO INPUT 1 (example)”.
“BEAM+SOUND OPTIMIZE” is selected automatically. When you
perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY”
only, refer to “AUTO SETUP via setup menu (p. 14)”.
Wait outside the room during the AUTO SETUP procedure.
The AUTO SETUP procedure takes about 3 minutes.
To cancel the AUTO SETUP procedure after it is started, press
RETURN key.
1) y 2) y
3) y
13 En
Initial settings
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
The screen below is displayed after connecting
IntelliBeam microphone to the unit.
1) 2)
4
Press ENTER key to start the AUTO
SETUP procedure and then leave the room
within 10 seconds.
3)
The setup screen automatically changes during the AUTO
SETUP procedure.
If AUTO SETUP procedure is complete, this unit rings
the chimes.
4)
AUTO SETUP
(PREPARATION & CHECK)
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from SoundPro-
jector. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
The best setting may not be done if you are in the room. Prepare to
leave the room in 10 seconds after pressing ENTER in step 4.
Note
MEASUREMENT COMPLETE.
BEAM MODE :5Beam/Plus2
SUBWOOFER :Yes
[ENTER]:Save set-up.
[RETURN]:Do
not save
set-up.
XXXXXXXXSHOW RESULTXXXXXXXXXX
Will begin in 10 sec.
Please leave the room.
---------
AUTO SETUP START
[RETURN]:Cancel
(After 3 min.)
5
Press ENTER key to confirm the
results.
5)
The measurement result is saved.
6
Remove the IntelliBeam microphone.
Initial screen appears.
6)
Keep the IntelliBeam microphone in a safe place.
The measurement results are stored in the internal
memory of this unit until you run the AUTO SETUP
procedure again or configure the settings manually.
You can save the several measurement result using
memory setting function (p. 16).
AUTO SETUP COMPLETE
Please remove the MIC
from Sound Projector
and the listening position.
If an error occurs, an error buzzer sounds and an error message is
displayed. For details on error messages, see “Error messages for
AUTO SETUP” (p. 15).
If “ENVIRONMENT CHECK:Failure” is displayed, refer to “Error
messages for AUTO SETUP” (p. 15), press RETURN key, and
then run the AUTO SETUP procedure again.
Depending on the environment of your listening room, the beam
angles of front right and left and surround left and right may be set to
the same value even if “BEAM MODE :5 Beam” is displayed as a
result.
If you do not want to reflect the results, press RETURN key.
When AUTO SETUP is performed from SETUP MENU, menu selection
screen of SETUP MENU appears.
4) y 5) y
6) y
Initial settings
14 En
AUTO SETUP via setup menu
1
Place the IntelliBeam microphone and
press SETUP key.
2
Press U / V to select “AUTO SETUP”
and then press ENTER key.
3
Press U / V to select one of the items
below and then press ENTER key.
Select Item:
“BEAM+SOUND OPTIMIZE” (Beam optimization
and sound optimization)
It is recommended that you should select this optimization
feature, if you make settings for the first time.
This menu takes about three minutes.
“BEAM OPTIMIZE ONLY”(Beam optimization
only)
Use to optimize the beam angle so that the parameter best
matches your listening environment.
This menu takes about one minute.
“SOUND OPTIMIZE ONLY”(Sound optimization
only)
Use to optimize the beam delay, volume, and quality so
that the parameters best match your listening environment.
You must optimize the beam angle with “BEAM
OPTIMIZE ONLY” before starting “SOUND OPTIMIZE
ONLY”. It is recommended that you should select this
optimization feature in the following cases:
If you have opened or closed the curtains in your
listening room before using this unit
If you have manually set the beam angle.
This menu takes about two minutes.
4
Connect the IntelliBeam microphone to
this unit after “AUTO SETUP
(PREPARATION & CHECK)” screen is
displayed.
For the details on installing and connecting IntelliBeam
microphone, refer to “Installing the IntelliBeam
microphone (p. 11)”.
5
Perform the step 4, 5 and 6 of “Using
AUTO SETUP (IntelliBeam) (p. 13)”.
6
After setup is completed, remove the
IntelliBeam microphone.
The best setting may not be done if you are in the room. Prepare to
leave the room in 10 seconds after pressing ENTER in step 4.
Note
15 En
Initial settings
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
Error messages for AUTO SETUP
If an error message is displayed on your TV, check the error
message list to solve the problem and then follow the procedure
below.
[ERROR E-1]: Press ENTER key to run the AUTO SETUP
procedure again. Or press Z key to continue the
measurement.
[ERROR E-7]: Press key to turn this unit to standby
mode, then run AUTO SETUP procedure again after turning this
unit on.
Other errors: Press RETURN key to cancel the operation
and then run the AUTO SETUP procedure again.
If the problem is difficult to be solved, configure the settings
manually in “SETUP MENU” (p. 32).
ERROR E-1: Please test in quieter environment.
Cause Remedy
There is too much unwanted
noise in your listening room.
Make sure that your listening
room is as quiet as possible. You
may want to choose certain hours
during the day when there is not
much noise coming from outside.
ERROR E-2: No MIC detected. Please check MIC
connection and re-try.
Cause Remedy
The IntelliBeam microphone is
not connected to this unit or
disconnected during the AUTO
SETUP procedure.
Connect the IntelliBeam
microphone to this unit firmly.
ERROR E-3: Unexpected control is detected. Please
re-try.
Cause Remedy
Some other operations were
performed on this unit while the
AUTO SETUP procedure was in
progress.
Do not perform any other
operations while the AUTO
SETUP procedure is in progress.
ERROR E-4: Please check MIC position. MIC should
be set in front of the Sound Projector and re-try.
Cause Remedy
The IntelliBeam microphone is
not placed in front of this unit.
Make sure that the IntelliBeam
microphone is installed in front
of this unit.
ERROR E-5: Please check MIC position. MIC should
be set above 1.8m/6.0ft and re-try.
Cause Remedy
The IntelliBeam microphone is
not placed in the right distance
from this unit.
Make sure that the IntelliBeam
microphone is installed more
than 1.8 m (6.0 ft) from the front
of this unit and within 1 m (3.3
ft) from the center height of this
unit.
ERROR E-6: Volume level is lower than expected.
Please check MIC position/connection and re-try.
Cause Remedy
The IntelliBeam microphone
cannot collect the sound
produced by this unit because the
sound output level is too low.
Make sure that the IntelliBeam
microphone is firmly connected
to this unit and placed in a proper
location. If the problem persists,
contact the nearest
authorized Yamaha service
center for assistance.
ERROR E-7: Unexpected error happened. Please
turn off and re-try.
Cause Remedy
An internal system error
occurred.
Press key to turn this unit
to standby mode, then run AUTO
SETUP procedure again after
turning this unit on.
ERROR E-8: Headphones are connected. Please
unplug the headphones and re-try.
Cause Remedy
A headphone is connected. Disconnect the headphone and
re-try.
Initial settings
16 En
You can save the current beam and sound settings in the system
memory of this unit. It is handy to save certain settings according
to the varying conditions of your listening environment. For
example, if there are curtains in the path of sound beams, the
effectiveness of the sound beams will vary depending on whether
the curtains are open or closed.
Saving settings
Saving several measurement results
(Memory setting function)
1
Press SETUP key.
2
Select “MEMORY” and press ENTER
key.
3
Press U / V key to select “SAVE”
and then press ENTER key.
4
Press U / V key to select the desired
memory number and then press ENTER
key.
1)
Selectable item: Memory 1, Memory 2, Memory 3
“Memory 1 Save Now ?” is displayed when the memory
number is selected.
5
Press ENTER key.
“Memory 1 Saving…” is displayed and the setting is
saved.
If there are curtains in your listening room, we recommend
following the procedure below.
1. While the curtains are open, run “BEAM+SOUND
OPTIMIZE” (p. 14) and then save the settings to
“Memory 1”.
2. While the curtains are closed, run “SOUND OPTIMIZE
ONLY” (p. 14) and then save the settings to
“Memory 2”.
If system settings are already stored in the selected memory number,
this unit overwrites the old settings.
Memory function cannot be set when “MEMORY PROTECT” is set
to “ON” in ADVANCED SETUP (p. 41).
1) y
17 En
Initial settings
PREPARATION PLAYBACK SETTINGS
TROUBLESHOOTING
ABOUT THIS UNIT English
CONNECTION/
INITIAL SETTINGS
Loading settings
1
Press SETUP key.
2
Select “MEMORY” and press ENTER
key.
3
Press U / V key to select “LOAD”
and press ENTER key.
4
Press U / V key to select the
memory number to be loaded and then
press ENTER key.
Selectable item: Memory 1, Memory 2, Memory 3
“Memory 1 Load Now ?” is displayed when the memory
number is selected.
5
Press ENTER key.
“Memory 1 Loading…” is displayed and the setting is
loaded.
Initial settings
18 En
You can use the TV remote control to operate this unit if your TV
supports the HDMI control function (ex. REGZA Link) and is
connected to this unit’s HDMI OUT (ARC) jack.
1)
Operating the unit by TV’s remote
control
What is the HDMI control function?
Remote control of TV (Example)
Power on/off
Controls the volume
Selects a component to
reproduce sounds (this
unit or TV)
Switches input
This unit automatically
selects the input according to
the input source setting on the
TV. Switching input on TV
menu (ex. selecting Blu-ray
disc player on TV menu) also
changes input of this unit.
Even if your TV supports the HDMI control function, some functions
may not be available. For details, refer to the manual supplied with
your TV.
If you use HDMI to connect this unit to a device such as a Blu-ray
disc player that supports HDMI control, you can control that device
using the HDMI control function.
We suggest that you use products (TV, Blu-ray disc/DVD player, etc.)
from the same manufacturer.
1) y
1 / 1

Yamaha YRS-1100 Omistajan opas

Kategoria
Receiver
Tyyppi
Omistajan opas
Tämä käsikirja sopii myös