Hitachi CS40EM Omistajan opas

GB

SE

DK

NO

FI

RU

GB

OWNER’S MANUAL

SE

Ägarhandbok

DK

BETJENINGSVEJLEDNING

NO

Bruksanvisning

FI

Omistajan opas

RU

Руководство пользователя

CHAINSAWS

Kedjesågar

MOTORSAVE

MOTORSAGER

KETJUSAHAT

ЦEПНЫE ПИЛЫ

CS40EM/45EM

970-82830-200 2007.07

G

B

D

K

F

I

S

E

N

O

R

U

G

B

GB-1

CS40EM/45EM

OWNER’S MANUAL

CHAIN SAWS

Read the manual carefully before

operating this machine.

GB-2

EXPLANATION OF SYMBOLS AND SAFETY WARNINGS

WARNING!!!

RISK OF DAMAGING HEARING

IN NORMAL CONDITIONS OF USE, THIS MACHINE

MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE

FOR THE OPERATOR EQUAL TO OR GREATER THAN

85 dB(A)

Read the manual carefully before

operating this machine.

Wear head, eye and ear

protection.

Use the chain saw

with two hands.

Warning! Danger of

kickback.

Read, understand and

follow all warnings.

MODEL

CS40EM 49.3 cm

3

/45EM

SOUND LEVEL

VIBRATION LEVEL

ISO 22868

LpA

ISO 22868

Lw measured

2000/14/EC

LwA

103.6 dB(A)

110 dB(A)

ISO 22867

100.8 dB(A)

Front handle Rear handle

5.5 m/s

2

7.2 m/s

2

G

B

GB-3

Contents

1. For Safe Operation ................................................................... 4

2. Explanation of Symbols on the Machine .................................. 6

3. Description ............................................................................... 7

4. Installing Guide Bar and Saw Chain......................................... 8

5. Fuel and Chain Oil .................................................................... 9

6. Operating the Engine ............................................................. 10

7. Sawing .................................................................................... 12

8. Maintenance ........................................................................... 13

9. Maintenance of Saw Chain and Guide Bar ............................ 14

10. Troubleshooting Guide ........................................................... 15

11. Specifications ......................................................................... 16

Yoshio Osada

Director

Signed in Chiba, Japan

DECLARATION OF CONFORMITY

(Directive 98/37/EC, EMC 89/336/EEC)

and to the regulations governing transposition

Internal control production

MANUFACTURER : Nikko Tanaka Engineering Co.,LTD

3-4-29 Tsudanuma

Narashino

Chiba, JAPAN

DECLARES THAT THE DESIGN OF THE MACHINE DESCRIBED BELOW :

Model : CS40EM/45EM

Serial no. : E57001 and up

Make : Nikko Tanaka Engineering

CONFORMS TO THE REQUIRMENTS OF THE MODIFIED MACHINES

DIRECTIVE (Directive 98/37/EC, EMC 89/336/EEC) AND TO THE NATIONAL

REGULATIONS GOVERNING ITS TRANSPOSITION ABROAD (ISO11681-1,

ISO12100-1 and -2, CISPR 12) : AND

THAT IT HAS BEEN ISSUED WITH A CE CERTIFICATE, NO. 404/05/1070

BY 404, SMP Svensk MaskinprovningAB, Fyrisborgsgaian 3, SE-754 50, Uppsala,

Sweden.

05/01/2007

GB-4

1. For safe operation

1. Never operate a chain saw when

you are fatigued, ill, or upset, or

under the influence of medica-

tion that may make you drowsy,

or if you are under the influence

of alcohol or drugs.

2. Use safety footwear, snug fitting

clothing and eye, hearing and

head protection devices.

Use the vibration-proof glove.

3. Keep the saw chain sharp and

the saw, including the AV system,

well maintained. A dull chain will

increase cutting time, and press-

ing a dull chain through wood will

increase the vibrations transmit-

ted to your hands. A saw with

loose components or with dam-

aged or worn AV buffers will also

tend to have higher vibration lev-

els.

4. All the above mentioned precau-

tions do not guarantee that you

will not sustain whitefinger

diseaseor carpal tunnel syn-

drome. Therefore, continual and

regular users should monitor

closely the condition of their

hands and fingers. If any of the

above symptoms appear, seek

medical advice immediately.

5. Always use caution when han-

dling fuel. Wipe up all spills and

then move the chain saw at least

3 m from the fueling point before

starting the engine.

6. Eliminate all sources of sparks or

flame (i.e. smoking, open flames,

or work that can cause sparks)

in the areas where fuel is mixed,

poured, or stored.

7. Do not smoke while handling fuel

or while operating the chain saw.

8. Do not allow other persons to be

near the chain saw when start-

ing or cutting. Keep bystanders

and animals out of the work area.

Children, pets and bystanders

should be a minimum of 10 m

away when you start or operate

the chain saw.

9. Never start cutting until you have

a clear work area, secure foot-

ing, and a planned retreat path

from the falling tree.

10. Always hold the chain saw firmly

with both hands when the engine

is running. Use a firm grip with

thumb and fingers encircling the

chain saw handles.

11. Keep all parts of your body away

from the saw chain when the en-

gine is running.

12.Before you start the engine,

make sure the saw chain is not

contacting anything.

13. Always carry the chain saw with

the engine stopped, the guide

bar and saw chain to the rear,

and the muffler away from your

body.

14. Never modify the unit or remove

the safety components in any way.

Do not use your unit for any job

except that for which it is intended.

Use only genuine HITACHI re-

placement parts as recom-

mended by the manufacturer.

15. Always inspect the chain saw be-

fore each use for worn, loose, or

damaged parts. Never operate

a chain saw that is damaged, im-

properly adjusted, or is not com-

pletely and securely assembled.

Be sure that the saw chain stops

moving when the throttle control

trigger is released.

16. All chain saw service, other than

the items listed in the Owner’s

Manual, should be performed by

competent chain saw service

personnel. (E.g., if improper tools

are used to remove the flywheel,

or if an improper tool is used to

hold the flywheel in order to re-

move the clutch, structural dam-

age to the flywheel could occur

which could subsequently cause

the flywheel to disintegrate.)

17. Always shut off the engine be-

fore setting it down.

G

B

GB-5

18. Use extreme caution when cut-

ting small size brush and sap-

lings because slender material

may catch the saw chain and be

whipped toward you or pull you

off balance.

19. When cutting a limb that is un-

der tension, be alert for spring-

back so that you will not be

struck when the tension in the

wood fibers is released.

20. Never cut in high wind, bad

weather, when visibility is poor or

in very high or low temperatures.

Always check the tree for dead

branches which could fall during

the felling operation.

21. Keep the handles dry, clean and

free of oil or fuel mixture.

22. Operate the chain saw only in

well ventilated areas. Never start

or run the engine inside a closed

room or building. Exhaust fumes

contain dangerous carbon mon-

oxide.

23. For respiratory protection, wear

a protection mask while emitting

the chain oil mist and dust from

sawdust.

24. Do not operate the chain saw in

a tree unless specially trained to

do so.

25. Guard against kickback. Kick-

back is the upward motion of the

guide bar which occurs when the

saw chain at the nose of the

guide bar contacts an object.

Kickback can lead to dangerous

loss of control of the chain saw.

26.When transporting or storage

your chain saw, make sure the

appropriate guide bar protector

is in place.

27. Clean and maintenance the unit

carefully and store it in the dry

place.

KICKBACK SAFETY PRECAU-

TIONS FOR CHAIN SAW USERS

WARNING

• Kickback may occur when the

nose or tip of the guide bar

touches an object, or when the

wood closes in and pinches the

saw chain in the cut. Tip con-

tact in some cases may cause

a lightning fast reverse reac-

tion, kicking the guide bar up

and back towards the operator.

Pinching the saw chain along

the top of the guide bar may

push the guide bar rapidly back

towards the operator. Either of

these reactions may cause you

to lose control of the saw, which

could result in serious personal

injury.

• Do not rely exclusively on the

safety devices built into your

saw. As a chain saw user you

should take several steps to

keep cutting jobs free from ac-

cident or injury.

(1) With a basic understanding of

kickback you can reduce or

eliminate the element of surprise.

Sudden surprise contributes to

accidents.

(2) Keep a good grip on the saw with

both hands, the right hand on the

rear handle, and the left hand on

the front handle, when the engine

is running. Use a firm grip with

thumbs and fingers encircling

the chain saw handles. A firm

grip will help you reduce kick-

back and maintain control of the

saw.

(3) Make certain that the area in

which you are cutting is free from

obstructions. Do not let the nose

of the guide bar contact a log,

branch, or any other obstruction

which could be hit while you are

operating the saw.

(4) Cut at high engine speeds.

(5) Do not overreach or cut above

shoulder height.

(6) Follow the manufacturer’s sharp-

ening and maintenance instruc-

tions for the saw chain.

(7) Only use replacement bars and

chains specified by the manufac-

turer or the equivalent.

GB-6

2. Explanation of Symbols on the Machine

WARNING

• For safe operation and maintenance, symbols are carved in relief on the machine.

According to these indications, please be careful not to make any mistake.

The screw under the “H” stamp is The High-speed adjustment screw.

The port to refuel “MIX GASOLINE”

Position: Fuel cap

The port to top up chain oil

Position: Oil cap

Setting the switch to the “ | ” position, the engine starts.

Setting the switch to the “O” position, the engine stops immediately.

Position: Rear-left of the unit

Starting the engine.

Starting mode when the engine is cold. (cold start)

Position: Upper-right of the aircleaner cover

Shows the directions that the chain brake is released (white arrow) and activated (black ar-

row).

Position: Front of the chain cover

The screw at the left of the “T” stamp is the Idle adjustment screw.

Position: Left side of the rear handle

The screw under the “L” stamp is The Slow-speed adjustment screw.

G

B

GB-7

3. Description

Since this manual covers several models, there may be some difference between pictures and your unit.

Use the instructions that apply to your unit.

1. Throttle trigger

2. Safety trigger

3. Ignition switch

4. Oil tank cap

5. Recoil starter

6. Front handle

7. Fuel tank cap

8. Decompression valve

9. Airfilter cover

10. Guide bar

11. Saw chain

12. Chain brake

13. Choke knob

14. Spiked bumper

15. Chain catcher

16. Side case

17. Guide bar clamp nut

GB-8

Power unit

Bar protector

Guide bar

Saw chain

Plug wrench

Screwdriver for

carburetor adjustment

NOTE

Pay attention to the correct direction of the saw chain.

5. Fit the chain cover to the power unit and fasten the

nuts to finger tightness.

6. While holding up the tip of the bar, adjust the chain

tension by turning the tensioner screw until the tie

straps just touch the bottom side of the bar rail.

7. Tighten the nuts securely with the bar tip held up

(12 ~ 15 N·m). Then check the chain for smooth ro-

tation and proper tension while moving it by hand. If

necessary, readjust with the chain cover loose.

8. Tighten the tensioner screw.

NOTE

A new chain will expand its length in the beginning of

use. Check and readjust the tension frequently as a loose

chain can easily derail or cause rapid wear of itself and

the guide bar.

4. Installing Guide Bar and Saw Chain

A standard saw unit package contains the items as illustrated.

Open the box and install the guide bar and the saw

chain on the power unit as follows:

* Install the provided spiked

bumper (1) to the unit with

the two screws.

WARNING

• The saw chain has very sharp edges. Use thick

protective gloves for safety.

1. Pull the guard towards the front handle to check that

the chain brake is not engaged.

2. Loosen the nuts and remove the chain cover.

3. Install the attached spike to the power unit.

4. Gear the chain to the sprocket and, while fitting the

saw chain around the guide bar, mount the guide

bar to the power unit. Adjust the position of chain

tensioner nut on the chain cover to the lower hole of

guide bar.

(1) Tensioner

screw

(2) Loosen

(3) Tighten

(1) Hole

(2) Tensioner nut

(3) Chain cover

Spike and mountaing screws

Moving direction

G

B

GB-9

5. Fuel and Chain Oil

■ FUEL

WARNING

• Gasoline is very flammable. Avoid smoking or

bringing any flame or sparks near fuel. Make sure

to stop the engine and allow it cool before refuel-

ing the unit. Select outdoor bare ground for fuel-

ing and move at least 3 m (10 ft) away from the

fueling point before starting the engine.

agitate depending on oil ingredients, sufficient agi-

tation is necessary for the engine to last long. Be

careful that, if the agitation is insufficient, there is an

increased danger of early piston seizing due to ab-

normally lean mixture.

5.

Put a clear indication on the outside of the container

to avoid mixing up with gasoline or other containers.

6. Indicate the contents on outside of container for easy

identification.

■ FUELING THE UNIT

1. Untwist and remove the fuel cap. Rest the cap on a

dustless place.

2. Put fuel into the fuel tank to 80% of the full capacity.

3. Fasten the fuel cap securely and wipe up any fuel

spillage around the unit.

WARNING

1. Select flat and bare ground for fueling.

2. Move at least 10 feet (3 meters) away from the

fueling point before starting the engine.

3. Stop the engine before refueling the unit. At that

time, be sure to sufficiently agitate the mixed

gasoline in the container.

■ FOR YOUR ENGINE LIFE, AVOID:

1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause

severe damage to the internal engine parts very

quickly.

2.

GASOHOL – It can cause deterioration of rubber and/

or plastic parts and disruption of engine lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark

plug fouling, exhaust port blocking, or piston ring

sticking.

4. Mixed fuels which have been left unused for a

period of one month or more may clog the carbu-

retor and result in the engine failing to operate prop-

erly.

5. In the case of storing the product for a long period

of time, clean the fuel tank after rendering it empty.

Next, activate the engine and empty the carburetor

of the composite fuel.

6. In the case of scrapping the used mixed oil con-

tainer, scrap it only at an authorized repository site.

NOTE

As for details of quality assurance, read the description

in the section Limited Warranty carefully. Moreover, nor-

mal wear and change in product with no functional in-

fluence are not covered by the warranty. Also, be care-

ful that, if the usage in the instruction manual is not ob-

served as to the mixed gasoline, etc. described therein,

it may not be covered by the warranty.

■ CHAIN OIL

Use motor oil SAE #10W-30 all year round or SAE

#30 ~ #40 in summer and SAE #20 in winter.

NOTE

Do not use wasted or regenerated oil that can cause

damage to the oil pump.

• The HITACHI engines are lubricated by oil specially

formulated for air-cooled 2-cycle gasoline engine use.

If genuine oil is not available, use an anti-oxidant

added quality oil expressly labeled for air-cooled 2-

cycle engine use(JASO FC GRADE OIL or ISO EGC

GRADE).

• Do not use BIA or TCW (2-stroke water-cooling type)

mixed oil.

■ RECOMMENDED MIXING RATIO

GASOLINE 50 : OIL 1

• Exhaust emission are controlled by the funda-

mental engine parameters and components (eq.,

carburation, ignition timing and port timing) with-

out addition of any major hardware or the intro-

duction of an inert material during combustion.

• These engines are certified to operate on unleaded

gasoline.

• Make sure to use gasoline with a minimum octane

number of 89RON (USA/Canada: 87AL).

• If you use a gasoline of a lower octane value than

prescribed, there is a danger that the engine tem-

perature may rise and an engine problem such as

piston seizing may consequently occur.

• Unleaded gasoline is recommended to reduce the

contamination of the air for the sake of your health

and the environment.

• Poor quality gasolines or oils may damage sealing

rings, fuel lines or fuel tank of the engine.

■ HOW TO MIX FUEL

WARNING

• Pay attention to agitation.

1. Measure out the quantities of gasoline and oil to be

mixed.

2. Put some of the gasoline into a clean, approved fuel

container.

3. Pour in all of the oil and agitate well.

4. Pour in the rest of gasoline and agitate again for at

least one minute. As some oils may be difficult to

GB-10

5. When you hear the engine want to start, with the

safety trigger pressed pull throttle trigger. This will

release the throttle from starting position to run po-

sition and will return the choke knob to run position

automatically.

6. Allow the engine to warm up with the throttle lever

pulled slightly.

WARNING

• Keep clear of the saw chain as it will start rotating

upon starting of engine.

■ CHECKING THE OIL SUPPLY

WARNING

• Make sure to set up the bar and the chain when

checking the oil supply.

If not, the rotating parts may be exposed. It is very

dangerous.

After starting the engine, run the chain at medium speed

and see if chain oil is scattered off as shown in the figure.

The chain oil flow can be changed by inserting a screw-

driver in the hole on bottom of the clutch side. Adjust

according to your work conditions.

NOTE

The oil tank should become nearly empty by the time

fuel is used up. Be sure to refill the oil tank every time

when refueling the saw.

■ ADJUSTING THE CARBURETOR

The carburetor on your unit has been factory adjusted,

but may require fine tuning due to a change in operat-

ing conditions.

Before adjusting the carburetor, make sure that the pro-

vided air/fuel filters are clean and fresh and the fuel prop-

erly mixed.

When adjusting, take the following steps:

NOTE

Be sure to adjust the carburetor with the bar chain at-

tached.

WARNING

• It is very dangerous to run a chainsaw that mounts

broken parts or lacks any parts.

Before starting engine, make sure that all the parts

including bar and chain are installed properly.

■ STARTING THE ENGINE

1. Fill fuel and chain oil tanks respectively, and tighten

the caps securely.

2. Set the switch to I position. Press the decompres-

sion valve (3).

3. Pull choke knob fully to choked position.

This will automatically lock the throttle in

starting position.

NOTE

If engine does not start easily, pull choke knob fully and

return it.

This will lock the throttle lever in starting position. Pull

recoil starter.

NOTE

Once the choke knob has been pulled out, it will not return

to the operating position even if you press down on it with

your finger. When you wish to return the choke knob to the

operating position, pull out the throttle lever instead.

4. While holding the saw unit securely on the ground,

pull the starter rope vigorously.

WARNING

• Do not start the engine while the chain saw

hangs in one hand. The saw chain may touch

your body. This in very dangerous.

6. Operating the Engine

(1) Chain oil

(2) Fuel

(3) Decompression valve

(1) Switch

(2) Throttle lever

(3) Throttle interlock

Chain oil

Chain oil flow

adjusting

(1) L needle

(2) H needle

(3) Idle adjusting screw

MAX

MIN

Choke knob

G

B

GB-11

In case the brake is not effective, ask our dealer for in-

spection and repairs.

If the engine keeps rotating at high speed with the brake

engaged, the clutch will overheat causing trouble.

When the brake engages during operation, immediately

release the throttle lever to stop the engine.

■ STOPPING THE ENGINE

1. Release the throttle lever to allow the engine to idle

for a few minutes.

2. Set the switch to the “O” (STOP) position.

Carburetor anti-freeze mechanism

Operating chain saws in temperatures of 0 – 5°C at times of

high humidity may result in ice forming within the carburetor,

and this in turn may cause the output power of the engine to

be reduced or for the engine to fail to operate smoothly.

This product has accordingly been designed with a ven-

tilation hatch on the right side of the surface of the cylin-

der cover to allow warm air to be supplied to the engine

and to thereby prevent icing from occurring.

Under normal circumstances the product should be

used in the normal operating mode, i.e., in the mode to

which it is set at the time of shipment. However when

the possibility exists that icing may occur, the unit should

be set to operate in the anti-freeze mode before use.

WARNING

• Continuing to use the product in the anti-freeze mode

even when temperatures have risen and returned to

normal, may result in the engine failing to start prop-

erly or in the engine failing to operate at its normal

speed, and for this reason you should always be sure

to return the unit to the normal operating mode if

there is no danger of icing occurring.

■ HOW TO SWITCH BETWEEN OPERATING MODES

1. Flip the engine switch to turn off the engine.

2. Remove the air cleaner cover from the cylinder cover

3. Loosen a screw and remove the screen on the back

of the air cleaner cover.

4. Turn the screen a half and reinstall to the cover.

When using the saw with the anti-freeze mode, frequently

check the screen and keep it clean of saw dust.

1. H and L needles are restricted within the number of

turn as shown below.

H needle : -

1

/

4

L needle : -

1

/

4

2. Start the engine and allow it to warm up in low speed

for a few minutes.

3. Turn the idle adjusting screw (T) counterclockwise

so that the saw chain does not turn. If the idling

speed is too slow, turn the screw clockwise.

4. Make a test cut and adjust the H needle for best

cutting power, not for maximum speed.

NOTE

Some models sold areas with strict exhaust emis-

sion regulation do not have high and low speed car-

buretor adjustments. Such adjustments may allow

the engine to be operated outside of their emission

compliance limits. For these models, the only car-

buretor adjustment is idle speed.

For models that equipped with low and high speed

adjustments; carburetors are pre set at the factory

Minor adjustments may optimize performance based

on climate, altitude, etc. Never turn the adjustment

screws in increments greater than 90 degrees, as

engine damage can result from incorrect adjustment

If you are not familiar with type of adjustment-assis-

tance HITACHI dealer.

■ CHAIN BRAKE

This machine is equipped with an automatic brake to

stop saw chain rotation upon occurrence of kickback

during saw cutting. The brake is automatically operated

by inertial force, which acts on the weight fitted inside

the front guard.

This brake can also be operated manually with the front

guard turned down to the guide bar.

To release the brake, pull up the front guard toward the

front handle till a “click” sound is heard.

[Caution]

Be sure to confirm brake operation during daily inspec-

tion.

How to confirm:

1) Turn off the engine.

2) Holding the chain saw horizontally, release your hand

from the front handle, hit the tip of the guide bar to a

stump or a piece of wood, and confirm brake op-

eration. Operating level varies by bar size.

(4) Normal operating mode

(5) Anti-freeze mode

(6) Screen

(1) Air cleaner cover

(2) Shutter plate

(3) Screw

GB-12

7. Sawing

• Before proceeding to your job,

read the section “For Safe Op-

eration”. It is recommended to

first practice sawing easy logs.

This also helps you get accus-

tomed to your unit.

• Always follow the safety regu-

lations. The chain saw must

only be used for cutting wood.

It is forbidden to cut other

types of material. Vibrations

and kickback vary with differ-

ent materials and the require-

ments of the safety regulations

would not be respected. Do not

use the chain saw as a lever for

lifting, moving or splitting ob-

jects. Do not lock it over fixed

stands. It is forbidden to hitch

tools or applications to the

PTO other than those specified

by the manufacturer.

• When completing a cut, be ready to hold up

the unit as it breaks into clear, so it will not

follow through and cut your legs, feet or body,

or contact an obstruction.

• Always keep the spiked bumper face to a tree,

because the chain may suddenly be drawn

into a tree.

• It is not necessary to force the saw into the

cut. Apply only light pressure while running the

engine at full throttle.

• When the saw chain is caught in the cut, do

not attempt to pull it out by force, but use a

wedge or a lever to open the way.

■ GUARD AGAINST KICKBACK

• This saw is equipped with a chain

brake that will stop the chain in the

event of kickback if operating prop-

erly. You must check the chain brake

operation before each usage by run-

ning the saw at full the throttle for I -

2 seconds and pushing the front

hand guard forward. The chain

should stop immediately with the en-

gine at full speed. If the chain is slow

to stop or does not stop, replace the

brake band and clutch drum before

use.

• It is extremely important that the

chain brake be checked for proper

operation before each use and that

the chain be sharp in order to main-

tain the kickback safety level of this

saw. Removal of the safety devices,

inadequate maintenance, or incor-

rect replacement of the bar or chain

may increase the risk to serious per-

sonal injury due to kickback.

■ FELLING A TREE

1. Decide the felling direction considering the wind,

lean of the tree, location of heavy branches, ease of

completing the task after felling and other factors.

2. While clearing the area around the tree, arrange a

good foothold and retreat path.

3. Make a notch cut one-third of the way into the tree

on the felling side.

4. Make a felling cut from the opposite side of the notch

and at a level slightly higher than the bottom of the

notch.

WARNING

• When you fell a tree, be sure to warn neighboring

workers of the danger.

Bucking and Limbing

WARNING

• Always ensure your foothold. Do not stand on the

log.

• Be alert to the rolling over of a cut log. Especially

when working on a slope, stand on the uphill side

of the log.

• Follow the instructions in “For Safe Operation” to

avoid kickback of the saw.

Before starting work, check the direction of bending

force inside the log to be cut. Always finish cutting from

the opposite side of the bending direction to prevent

the guide bar from being caught in the cut.

Notch cut

Felling cut

Felling direction

WARNING

G

B

GB-13

8. Maintenance

Oiling port

Grease port

Sprocket

Oiling port

A log lying on the ground

Saw down halfway, then roll the log over and cut from

the opposite side.

A log hanging off the ground

In area A, saw up from the bottom one-third and finish

by sawing down from the top. In area B, saw down from

the top one-third and finish by sawing up from the bot-

tom.

Cutting the limbs of Fallen Tree

First check to which side the limb is bent. Then make

the initial cut from the bent side and finish by sawing

from the opposite side.

WARNING

• Be alert to the springing back of a cut limb.

Pruning of Standing Tree

Cut up from the bottom, finish down from the top.

WARNING

• Do not overreach.

• Do not cut above shoulder height.

• Always use both your hands to hold the saw.

3. Guide bar

When the guide bar is dismounted, remove sawdust in the bar

groove and the oiling port.

Grease the nose sprocket from the feeding port on the tip of

the bar.

4. Others

Check for fuel leakage and loose fastenings and damage to

major parts, especially handle joints and guide bar mounting.

If any defects are found, make sure to have them repaired

before operating the saw again.

■ PERIODICAL SERVICE POINTS

1. Cylinder fins

Dust clogging between the cylinder fins will cause overheat-

ing of the engine. Periodically check and clean the cylinder

fins after removing the air cleaner and the cylinder cover. When

installing the cylinder cover, make sure that switch wires and

grommets are positioned correctly in place.

NOTE

Be sure to block the air intake hole.

WARNING

• Before cleaning, the inspecting or repairing the unit,

make sure that engine has stopped and is cool. Dis-

connect the spark plug to prevent accidental starting.

■ MAINTENANCE AFTER EACH USE

1. Air filter

Dust on the cleaner surface can be removed by tapping a

corner of the cleaner against a hard surface. To clean dirt in

the meshes, split the cleaner into halves and brush in gaso-

line. When using compressed air, blow from the inside.

To assemble the cleaner halves, press the rim until it clicks.

NOTE

When installing the main filter, make sure that the grooves

on the filter edge are correctly fit with the projections on

the cylinder cover.

2. Oiling port

Dismount the guide bar and check the oiling port for clogging.

GB-14

Place the file on the cutter and push straight forward.

Keep the file position as illustrated.

After each cutter has been filed, check the depth gauge

and file it to the proper level as illustrated.

4. Spark plug

Clean the electrodes with a wire brush and reset the gap to

0.65 mm as necessary.

5. Sprocket

Check for cracks and for excessive wear interfering with the

chain drive. If the wear is considerable, replace it with new

one. Never fit a new chain on a worn sprocket, or a worn chain

on a new sprocket.

6. Front and Rear dampers

Replace if adhered part is peeled or crack is observed on the

rubber part.

2. Fuel filter

(a) Using a wire hook, take out the filter from the filler port.

(b) Disassemble the filter and wash with gasoline, or replace

with a new one if needed.

NOTE

• After removing the filter, use a pinch to hold the end

of the suction pipe.

• When assembling the filter, take care not to allow fil-

ter fibers or dust inside the suction pipe.

3. Oil tank

With a wire hook, take out the oil filter through the filler port and

clean in gasoline. When putting the filter back into the tank,

make sure that it comes to the front right corner. Also clean off

dirt in the tank.

Fuel filter

9. Maintenance of Saw Chain and Guide Bar

Appropriate gauge checker

Champion NGK

CS40EM/45EM RCJ-6Y BPMR8Y

Depth gauge standard

21BP: .025

″″

″ (0.64 mm)

33SL: .020

″″

″ (0.51 mm)

Make the shoulder round

Oil filter

0.6 ~ 0.7 mm

■ Saw Chain

WARNING

• It is very important for smooth and safe operation

to always keep the cutters sharp.

The cutters need to be sharpened when:

• Sawdust becomes powder-like.

• You need extra force to saw in.

• The cut path does not go straight.

• Vibration increases.

• Fuel consumption increases.

Cutter setting standards:

WARNING

• Be sure to wear safety gloves.

Before filing:

• Make sure the saw chain is held securely.

• Make sure the engine is stopped.

• Use a round file of proper size for the chain.

Chain type: 21BP/20BP 33SL

File size: 3/16 in (4.76 mm) 5/32 in (3.97 mm)

G

B

GB-15

WARNING

• This saw is equipped with one of the following low

kickback bar/chain combinations:

HITACHI Part Number

Bar Size Guide Bar Saw Chain

16 107-72811-200 138-32625-20(21BP-66E)

18 105-72830-201 136-32578-20(21BP-72E)

• The bar rail should always be square. Check for wear

of the bar rail. Apply a ruler to the bar and the out-

side of a cutter. If a gap is observed between them,

the rail is normal. Otherwise, the bar rail is worn.

Such a bar needs to be corrected or replaced.

10. Troubleshooting Guide

Case 1. Starting failure

WARNING

• Make sure the icing prevention system is not working.

Check fuel for water

or substandard mix-

ture.

Replace with proper

fuel.

Check for engine

flooding.

Check spark ignition.

Remove and dry the

spark plug.

Then pull the starter

again with no choke.

Replace with a new

plug.

Case 2. Lack of power/Poor acceleration/

Rough idling

Case 3. Oil does not come out

Check fuel for water

or substandard mix-

ture.

Check air filter and

fuel filter for clog-

ging.

Check carburetor

for inadequate ad-

justment.

If the unit seems to need further service, please consult

with an authorized service shop in your area.

Replace with proper

fuel.

Clean.

Readjust speed

needles.

Check oil for sub-

standard quality.

Check oil passage

and ports for clog-

ging.

Replace.

Clean.

a

d

a

d

a

d

a

WARNING

• Be sure to round off the front edge to reduce the

chance of kickback or tie-strap breakage.

Make sure every cutter has the same length and edge

angles as illustrated.

■ Guide Bar

• Reverse the bar occasionally to prevent partial wear.

Cutter length

Filing angle

Side plate angle

Top plate cutting angle

Ruler

Gap

No gap

Chain tilts

GB-16

11. Specifications

Power unit:

Displacement (cm

3

): ............................................. 49.3

Fuel: ................ Mixture (Gasoline 50 : Two-cycle oil 1)

Fuel tank capacity (cm

3

): ....................................... 550

Chain oil: ................................. Motor oil SAE# 10W-30

Oil tank capacity (cm

3

):.......................................... 260

Carburetor: .....................Diaphragm type (Walbro WT)

ignition system: .....................................Pointless (CDl)

Spark plug:......................................Champion RCJ-6Y

Oil feeding system: ...... Automatic pump with adjuster

Sprocket (Teeth x Pitch): ............................ 7T x 0.325

″

Dimensions (L x W x H) (mm): ............ 410 x 235 x 265

Dry weight (kg): .................................................... 4.90

Cutting head:

Guide bar

Type: ................................................ Sprocket nose

Size (in. (mm)): ........................... CS40EM 16 (400)

CS45EM 18 (450)

Saw chain

Type: .................................................. Oregon 21BP

Pitch (in. (mm)):.................................... 0.325 (8.26)

Gauge (in. (mm)):................................. 0.058 (1.47)

Type: .................................................. Oregon 33SL

Pitch (in. (mm)):.................................... 0.325 (8.26)

Gauge (in. (mm)):................................. 0.050 (1.27)

Power (kw/min

-1

) ........................................ 2.51/10,000

Max speed (min

-1

) ............................................. 13,000

Idle speed (min

-1

) ................................................ 2,500

Specifications are subject to change without notice.

S

E

SE-1

CS40EM/45EM

Ägarhandbok

Kedjesågar

Läs noga igenom bruksanvisningen

innan maskinen tas i bruk.

SE-2

FÖRKLARING TILL SYMBOLER OCH SÄKERHETSVARNINGAR

VARNING!!!

RISK FÖR HÖRSELSKADOR

UNDER NORMALA ANVÄNDNINGSFÖRHÅLLANDEN KAN DEN HÄR

MASKINEN ORSAKA DAGLIG EXPONERING FÖR PERSONAL TILL BULLER

UPPGÅENDE TILL ELLER STARKARE ÄN

85 dB(A)

Läs noga igenom

bruksanvisningen

innan maskinen tas i bruk.

Använd alltid båda händerna

när du arbetar med kedjesågen.

Läs, förstå och

beakta alla

varningar.

Använd skyddshjälm,

ögonskydd och

hörselskydd.

Varning! Risk för kast!

MODELL

CS40EM 49.3 cm

3

/45EM

LJUDNIVÅ

VIBRATIONSNIVÅ

ISO 22868

LpA

ISO 22868

Uppmätt ljudeffekt

(Lw)

2000/14/EC

LwA

103.6 dB(A)

110 dB(A)

ISO 22867

100.8 dB(A)

Främre

handtag

Bakre handtag

5.5 m/s

2

7.2 m/s

2

S

E

SE-3

Innehåll

1. För säker användning ............................................................... 4

2. Förklaring av symbolerna på maskinen.................................... 6

3. Beskrivning ............................................................................... 7

4. Montera svärd och sågkedja .................................................... 8

5. Bränsle och kedjeolja ............................................................... 9

6. Handhavande av motor .......................................................... 10

7. Sågning .................................................................................. 12

8. Underhåll ................................................................................ 13

9. Underhåll av sågkedja och svärd........................................... 14

10. Felsökning .............................................................................. 15

11. Tekniska data .......................................................................... 16

Yoshio Osada

Direktör

Chiba, Japan

FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

(med direktiven 98/37/EG och EMC 89/336/EEG)

samt med de förordningar som reglerar förflyttning och

produktion med intern kontroll

TILLVERKARE : Nikko Tanaka Engineering Co.,LTD

3-4-29 Tsudanuma

Narashinoy

Chiba, Japan

INTYGAR ATT KONSTRUKTIONEN AV DEN NEDAN BESKRIVNA MASKINEN:

Modell : CS40EM/45EM

Serienr. : E57001 och uppåt

Märke : Nikko Tanaka Engineering

UPPFYLLER KRAVEN ENLIGT DE MODIFIERADE MASKINDIREKTIVEN

(direktiven 98/37/EG och EMC 89/336/EEG) OCH DE NATIONELLA

FÖRORDNINGAR SOM REGLERAR DESS FÖRFLYTTNING UTOMLANDS

(ISO 11681-1, ISO 12100-1 och -2 samt CISPR 12) SAMT

HAR FÖRSETTS MED ETT CE-CERTIFIKAT (nr 404/05/1070) AV 404, SMP,

Svensk Maskinprovning AB, Fyrisborgsgatan 3, 754 50 Uppsala, Sverige.

05/01/2007

Sivu latautuu ...

Hitachi CS40EM Omistajan opas

Tämä käsikirja sopii myös

Hitachi CS40EM Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat