Yamaha SW1000XG Omistajan opas

Merkki: Yamaha

Malli: SW1000XG

Luokka: Synthesizer

Tyyppi: Omistajan opas

PCI AUDIO MIDI CARD

OWNER'S MANUAL

SW1000XG-E.qx 4/2/99 4:31 PM Page 1

CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

1. IMPORTANT NOTICE: DO NOT MODIFY

THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your

FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a rea-

sonable level of assurance that your use of this prod-

uct in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other elec-

tronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in

all installations. If this product is found to be the

source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following meas-

ures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch (cir-

cuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference,

relocate/reorient the antenna. If the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to co-

axial type cable.

If these corrective measures do not produce satis-

factory results, please contact the local retailer

authorized to distribute this type of product. If you

can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic

Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

SW1000XG-E.qx 4/2/99 4:31 PM Page 2

Introduction

Thank you very much for purchasing Yamaha’s SW1000XG.

In this package you will find a sound card that offers both high quality XG sound and a com-

plete digital audio environment. To help you take utmost advantage of the advanced features of

your new SW1000XG, we have packed it together with a variety of applications that work togeth-

er with your sound card to help you bring your musical ideas to reality. Since the SW1000XG

puts this remarkable MIDI + audio music control environment right inside your computer, you

can do everything right from your PC—even mastering compact disks.

Read this manual carefully before using your SW1000XG to make sure you get the most enjoy-

ment out of your investment in quality sound.

After you finish reading your owner’s manual, be sure to keep it someplace safe where you can

refer to it whenever you have a question about your sound card.

Special Notices

• The SW1000XG software and this owner’s manual are exclusive copyrights of Yamaha

Corporation.

• Copying of the software or reproduction of this manual in whole or in part by any means is

expressly forbidden without the written consent of the manufacturer.

• Yamaha makes no representations or warranties with regard to the use of the software and

documentation and cannot be held responsible for the results of the use of this manual and

the software.

• This disk is a CD-ROM. Do not attempt to play the disk on an audio CD player. Doing so

may result in irreparable damage to your audio CD player.

• Copying of the commercially available music sequence data and/or digital audio files is strict-

ly prohibited except for your personal use.

• The company names and product names in this Owner’s Manual are the trademarks or regis-

tered trademarks of their respective companies.

• The screen displays as illustrated in this Owner’s Manual are for instructional purposes, and

may appear somewhat different from the screens which appear on your computer.

• Future upgrades of application and system software and any changes in specifications and

functions will be announced separately.

Windows Operation

This owner’s manual assumes that you are already familiar with basic Windows operation. If you

are not, please refer to the owner’s manual which came with your Windows software before

using SW1000XG.

● Do not expose the soundcard to direct sunlight, excessive

humidity, high temperatures, excessive dust or strong vibrations.

● Before handling the soundcard, be sure to touch a metal surface

to discharge any static electricity which may be in your body.

● When holding the soundcard, do not touch the inside area of the

circuit board or apply excessive pressure to the card, and be

sure to protect the card from contact with water or other liquids.

● Before installing the soundcard in the computer, unplug the

power connector of your computer.

● Before connecting the computer to other devices, turn off the

power switches of all devices.

● It is possible that computer malfunctions or operator actions

might destroy data that was created with the included application

software. We recommend that you back up all important data

onto floppy disks. Yamaha is not responsible for loss of data

through computer malfunctions or operator actions.

● The soundcard contains no user-serviceable parts, so never

touch the inside area of the circuit board or tamper with the elec-

tronic circuitry in any way. Doing so may result in electrical shock

or damage to the soundcard.

Precautions

YAMAHA CANNOT BE HELD RESPONSIBLE FOR

DAMAGE CAUSED BY IMPROPER CARE AND USE

OF THE SOUNDCARD AND SOFTWARE.

SW1000XG-E.qx 4/2/99 4:31 PM Page 3

SW1000XG Features

AWM Wave Table

• Using the AWM2 (Advanced Wave Memory 2) tone generator, the wave table built into the SW1000XG

offers high quality sound with 1267 normal voices and 46 drum kits playing with 32 part/64 polyphony

(the maximum number of simultaneous sounds). The quality of sound rivals that of Yamaha’s MU100 tone

generator, which is top-class, even among tone generators for personal computer-based music system.

Full Array of Effects

• The SW1000XG comes equipped with a total of six effect blocks: reverb (12 types), chorus (14 types),

variation (70 types), insertion 1/2 (43 types for each), and five band multi EQ (four types). The

SW1000XG does more than offer effects for an ensemble as a whole. It also lets you craft detailed

effect settings for each instrument part, creating an elaborate world of sound using just one sound card.

The effects can be applied not only to the internal tone generator, but also to input from external

audio sources such as wave data (digital audio) or to microphone input.

GM/XG Compatible

• Because the SW1000XG sound card is compatible with the GM standard and Yamaha’s exclusive XG

extensions to GM, you can enjoy playing commercially available GM and XG song collections with

high quality sound.

GM (General MIDI System Level 1) is an addition to the MIDI standard which ensures that any

GM-compatible music data can be accurately played by any GM-compatible tone generator,

regardless of maker. With the GM standard, you can assign any of the 128 GM-compatible voices

to each of the 16 parts, or MIDI channels. (Channel 10 is fixed as the drum part.)

XG is a new MIDI format created by Yamaha which significantly improves and expands upon the

General MIDI standard by providing a greater variety of high-quality voices plus considerably

enhanced effect operation—while being fully compatible with GM.

MIDI Interface Function

• You can connect your sound card to an external MIDI keyboard or other MIDI device using the MIDI

adapter cable that was included with your SW1000XG.

Expanded Capability with an XG Plug-In Board

• You can add expanded functions like a VL (physical model) tone generator to the standard AWM2 tone

generator in your SW1000XG sound card by simply connecting an XG Plug-In System compatible plug-

in option board (PLG100 series).

Digital Audio Recording/Playback

• The SW1000XG features six stereo wave playback devices and two stereo wave recording devices.

Among the two stereo recording devices, one is for external audio input (A/D input) only, and the

other mixes external audio input (A/D input), AWM2 tone generator sound, and wave tracks in the

sequence software.

Using the included XGworks for SW1000XG software as an example, wave data on multiple tracks can

be sent to the SW1000XG sound card audio parts (maximum 12 parts), and played simultaneously with

each part having effects applied.

Mic/Line input can be recorded on a wave track (in either stereo or mono) in time with playback of

MIDI tracks (or MIDI tracks and wave tracks). With this feature, it’s easy to lay down multiple record-

ings for things like vocals, with the AWM2 tone generator of the SW1000XG playing in the background.

When you make a song using this feature, you can play back all the MIDI tracks and wave tracks

simultaneously, then record the entire output together on a single wave track. When you do this, all

the tracks of a song can be united into one as wave data, then mastered. The mastered audio data can

then be used as a file for writing on a CD-R disk.

Digital Output

• Stereo digital out (S/PDIF) connector is equipped on the SW1000XG. Also, when you connect an

optional digital mixing card (DS2416), you can send digital output from the SW1000XG to the DS2416

on one pair of stereo outputs and six individual outputs. This means that even if no external digital

mixer is available, you can control every aspect of your music, including digital mixing, from within

your computer.

SW1000XG-E.qx 4/2/99 4:31 PM Page 4

Table of Contents

Introduction .......................................................................................................3

Special Notices ..............................................................................................................................3

Windows Operation......................................................................................................................3

SW1000XG Features ...........................................................................................4

Before Using .......................................................................................................6

Package Contents ..........................................................................................................................6

Items You Will Need that Are Not Included...............................................................................6

Introducing the Included Software ..................................................................7

SW1000XG Sound Card Connections ...............................................................9

The Terminals on the SW1000XG................................................................................................9

Installing Your Sound Card ........................................................................................................10

Installing the Plug-In Board .......................................................................................................12

Installing the Digital Mixing Card ..............................................................................................12

Installation of the Driver.................................................................................13

Installing the driver for Windows95 OSR2 (4.00.950B)............................................................13

Installing the driver for Windows95 (4.00.950 or 4.00.950A) ..................................................15

Installation of the Software.............................................................................16

Installing XGworks for SW1000XG and Wave Editor TWE......................................................16

Installing XG Plug-In Software...................................................................................................19

SW1000XG Overview and Features.................................................................22

Sound Module Modes .................................................................................................................22

Voices ...........................................................................................................................................22

Selecting Voices ...........................................................................................................................23

Effect Types .................................................................................................................................23

A/D Input ....................................................................................................................................24

About the Plug-In System...........................................................................................................24

Supplementary Items for XGworks 2.0..........................................................25

Simultaneous Playback of Multiple Wave Tracks and Playback Part-Way Through ..............25

System Setup Dialog ...................................................................................................................25

Track View Window ...................................................................................................................28

XG Editor Window......................................................................................................................29

Wave Data Can Also Be Saved in a Song .................................................................................31

Opening the Wave Editor TWE..................................................................................................31

SW1000XG Mixer ........................................................................................................................32

MIDI Implementation Chart............................................................................40

Specifications of the SW1000XG Sound Card ................................................42

Troubleshooting...............................................................................................43

* The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from

the screens which appear on your computer.

SW1000XG-E.qx 4/2/99 4:31 PM Page 5

Before Using

Package Contents

Before using your new SW1000XG, check that all the items below are included in the package. In

the rare case that some item is missing, contact the store where you purchased your sound card

as soon as possible.

SW1000XG sound card

• MIDI adapter cable (1)

• Plug-in board connection cable (1)

• Spacers for plug-in board (4)

CD-ROM

Owner’s Manual (this book)

Items You Will Need that Are Not Included

To use your SW1000XG sound card and the included software, you will also need the following

hardware and software:

Computer: CPU/Memory An IBM compatible personal computer

with a 166 MHz or higher Pentium CPU,

and at least 32 MB of memory.

Hard Disk To use the software included with

SW1000XG, the software and drivers must

be installed. To install and use the soft-

ware, at least 20 MB of hard disk space is

required.

CD-ROM Drive All the software that came with your sound

card is included on the supplied CD-ROM.

To install the software and to read the

demo songs, a CD-ROM drive is required.

Mouse Operations in the included software are

mainly done using a mouse.

PCI Expansion Slot To install the sound card, an empty PCI

slot is required.

Operating System Windows 95 is required.

If the Windows 95 version installed on your computer is OSR2 or higher, you can use IRQ shar-

ing. Because versions of Windows 95 earlier than that do not allow IRQ sharing, conflicts with

other boards may happen or installation may not be possible. Should this occur, change the IRQ

settings or remove the conflicting board.

n You can check which version of Windows 95 is installed on your computer by clicking [My Computer], then

[Control Panel], then [System]. If the version number displayed on the [General] page is 4.00.950 B, you have OSR2.

If the number is 4.00.950 or 4.00.950 A, you have a previous version of Windows 95.

SW1000XG-E.qx 4/2/99 4:31 PM Page 6

Introducin

the

Included Software

The software programs that are included in this package are introduced here. For information

about installing each of them, see “Installation of the Software” on page 16.

• XGworks for SW1000XG

This is MIDI sequence software for Windows 95. Besides letting you enter and edit MIDI data,

XGworks supports digital recording and features an XG Editor that makes it easy to edit the XG

voices. These and other advanced features are just the tools you need to enjoy creating high

quality music. For details about XGworks, see the included XGworks 2.0 Owner’s Manual (PDF

file in the supplied CD-ROM’s “Document” folder).

n To view PDF files, you must first install the Acrobat Reader. A program for doing this has been provided in the

Acrobat folder on the CD-ROM that came with your SW1000XG sound card. To install Acrobat Reader, double-

click on the ar32e301.exe installation program in that folder.

Because the version of XGworks in this package is an upgrade specially developed for

your SW1000XG sound card, some important supplemental information has been

included in this manual, starting from page 25. Please read this information together

with your XGworks manual.

• Wave Editor TWE

This software lets you edit the waveform data in wave files (extension .WAV) that have been

recorded onto WAVE tracks in XGworks. Wave files can also be recorded using Wave Editor

TWE. For detailed information about using this program after installation, click on the [Start]

button in Windows 95, then select [YAMAHA XGworks for SW1000XG] from the [Program]

menu. Selecting [WAVE Editor TWE Manual] will display the online manual for the wave editor

(PDF file).

n To view PDF files, you must first install the Acrobat Reader. A program for doing this has been provided in the

Acrobat folder on the CD-ROM that came with your SW1000XG sound card. To install Acrobat Reader, double-

click on the ar32e301.exe installation program in that folder.

n Besides wave files with the extension .WAV, the Wave Editor TWE software also supports recording and editing

AIFF files. However, these files cannot be used in XGworks.

• VL Visual Editor

The VL Visual Editor is editing software for the optional PLG100-VL board (→ P. 24) sold sepa-

rately. For detailed information on using it, install the software, then start the VL Visual Editor

in XGworks. Select [Contents] from the [Help] menu to read the online help.

• VH Effect Editor

The VH Effect Editor is editing software for the optional PLG100-VH board (→ P. 24) sold sepa-

rately. For detailed information on using it, install the software, then start the VH Effect Editor

in XGworks. Select [Contents] from the [Help] menu to read the online help.

• DX Easy Editor

The DX Easy Editor is simple editing software for the optional PLG100-DX board (→ P. 24) sold

separately. For detailed information on using it, install the software, then start the DX Easy

Editor in XGworks. Select [Contents] from the [Help] menu to read the online help.

SW1000XG-E.qx 4/2/99 4:31 PM Page 7

• DX Simulator

The DX Simulator is editing software for the optional PLG100-DX board (→ P. 24) sold sepa-

rately. Using exactly the same user interface as the famous Yamaha DX7, you can create finely-

crafted sounds. For detailed information on using this program, install the software, then start

the DX Simulator in XGworks. Select [Contents] from the [Help] menu to read the online help.

• SW1000XG Windows95 Driver

This driver is necessary for playing sounds using the SW1000XG sound card. See page 13 for

instructions on installing this driver.

• SW1000XG Demo Songs

The SW1000XG demo songs showcase the high quality expressive power of the SW1000XG

sound card. Since they feature both MIDI and audio tracks, you can enjoy them by playing

them in XGworks for SW1000XG.

They are included in the supplied CD-ROM’s “Demo” folder.

n Besides the SW1000XG demo songs with both MIDI and audio tracks, other demo songs that are standard MIDI

files have also been provided in this package. These standard MIDI files will be installed together with XGworks.

• SW1000XG Data Lists

The voice list, materials about the effects, and the MIDI data format for your SW1000XG sound

card have all been provided in PDF file format for your reference. They are collected in the file

“Data_E.PDF,” which is in the Document folder of the CD-ROM that came with your sound

card.

n To view PDF files, you must first install the Acrobat Reader. A program for doing this has been provided in the

Acrobat folder on the CD-ROM that came with your SW1000XG sound card. To install Acrobat Reader, double-

click on the ar32e301.exe installation program in that folder.

SW1000XG-E.qx 4/2/99 4:31 PM Page 8

SW1000XG Sound

Card Connections

The Terminals on the SW1000XG

Before handling the sound card, make sure to eliminate any static electricity in your clothes or body by touching a

metal surface that is definitely grounded. Also, be careful to avoid touching any parts on the sound card’s circuit

board, or any of the connectors.

1 External Audio Input (A/D input) Terminal

This terminal is stereo line input for audio signals from external devices such as a mike, gui-

tar, bass, or CD player. It connects to a stereo mini-jack cable.

2 Line Out L/R Terminal

This terminal is for external output of audio signals in stereo. It connects to an audio device

or mixer with RCA pin jack cables.

The white terminal is L (left) and the red terminal is R (right).

3 Digital Out Terminal

This terminal is for digital output of audio signals in stereo. It connects to a digital audio

device or mixer with digital input through a S/PDIF type cable.

4 MINI DIN 6 Pin Terminal

This terminal is for connecting to an external MIDI device such as a keyboard, using the

included MIDI adapter cable.

5 Plug-In Board (PLG100 Series) Connector

This terminal connects to an optional plug-in board compatible with the XG plug-in system

(PLG100 series). These boards can be used to expand the functions of the XG tone generator

that is standard on the SW1000XG sound card.

6 Digital Mixing Card (DS2416) Connector

This terminal connects to the digital mixing card (DS2416) sold separately. Output from the

SW1000XG can be sent to a digital mixing card equivalent to the Yamaha O2R digital mixer

over a pair of stereo outputs and six individual outputs. Even when no external digital mixer

is available, you can control every aspect of your music including digital mixing — all from

within your computer.

5 6

Microphone, etc.

Powered speakers

DAT, etc.

MIDI IN

MIDI OUT

MIDI IN

MIDI Keyboard

MIDI adapter cable (included)

00:00:00

DAT

Digital Mixing Card (DS2416)

SW1000XG

Plug-In Board (PLG 100 series)

To Serial In Connector

To XG plug-in board connector

MIDI KEYBOARD CBX-K1

SW1000XG-E.qx 4/2/99 4:31 PM Page 9

Installing Your Sound Card

The SW1000XG sound card can be installed in your computer by simply following these steps:

n Before installing your sound card, check to be sure that there is an empty PCI card slot in your computer. If you

are going to use a slot where there is already a PCI card installed, uninstall the driver software for that card, then

turn off the power to the computer and remove the card. Restarting the computer after doing this will cause it to

recognize that the card that was in that slot has been completely removed. After completing this series of opera-

tions, turn off the power to your computer again before following the installation procedure below.

n If you will be installing a plug-in board (PLG100 series) or digital mixing card (DS2416) on your sound card, be

sure to also read the instructions for doing that (→ P. 12).

1. Unplug the computer power cord from the electrical outlet.

There is a serious danger of electric shock if you attempt to install the sound card while the computer power is

turned on. Be absolutely sure to turn OFF the power and unplug the computer before proceeding with the installa-

tion.

2. Remove the cover from the main body of the computer.

n The method for removing the cover and the location of the PCI slots varies for each computer model. Refer

to the owner’s manual for your computer to obtain this information.

3. Remove the cover for the PCI slot.

SW1000XG-E.qx 4/2/99 4:31 PM Page 10

4. Remove the sound card from its anti-static bag.

Before handling the sound card, make sure to eliminate any static electricity in your clothes or body by touch-

ing a metal surface that is definitely grounded. Also, be careful to avoid touching any parts on the sound

card’s circuit board, or any of the connectors.

5. Insert the connector on the sound card into the connector on the computer. Hold the card

by both ends with both hands, and slowly push the card into the computer slot. When doing

this, make sure that you are not installing the card upside down.

6. Secure the sound card with the screw if this is required in your computer, then reinstall the

cover for the main body of the computer.

n The method for securing the PCI expansion card, and for reinstalling the cover varies for each computer

model. Refer to the owner’s manual for your computer to obtain this information.

7. Connect the external devices you will use with your sound card (such as speakers, mixer, or

MIDI keyboard) to the appropriate connectors on the SW1000XG.

n When removing your sound card, follow the steps above in reverse order.

SW1000XG-E.qx 4/2/99 4:31 PM Page 11

Installing the Plug-In Board

Refer to the illustration below to install an optional plug-in board (PLG100 series).

Making sure that the plug-in board is facing in the correct direction, carefully press the cable

from the plug-in board into the plug-in board connector on the sound card.

n This should be done before the sound card is installed in the computer.

n For information about each plug-in board, see page 24 and the owner’s manual that comes with each board.

Installing the Digital Mixing Card

Refer to the illustration below to install an optional digital mixing card (DS2416).

Making sure that the flat cable from the digital mixing card (DS2416) is facing in the correct

direction, carefully press the cable into the digital mixing card connector on the sound card.

n This should be done before the sound card is installed in the computer.

n For information about the digital mixing card (DS2416), refer to the owner’s manual that comes with the card.

Green line

Serial In Connector

Serial out Connector

DS2416

SW1000XG sound card

Connector to SW1000XG

Connector to DS2416

Green line

Make sure that

the flat cable from

the DS2416 is

facing in the

correct direction.

Make sure that the flat cable is

facing in the correct direction.

Flat cable's

connector

SW1000XG sound card

Yellow line

Plug-in board

Spacer

Connector to SW1000XG

Connector to plug-in board

Yellow line

First, put the four spacers in

the SW1000XG, then fit

the plug-in board above

the sound card.

Hooks To plug-in board

To SW1000XG

Spacer

Output from the SW1000XG to the DS2416 digital mixing card

In the initial setting, all parts of the SW1000XG are mixed in stereo and sent to the DS2416.

However, you can send a specific part as an individual output to the DS2416, apart from the

stereo output.

The SW1000XG is equipped with 6 individual outputs and each part (either MIDI multi part

or audio part) can be assigned to any of the individual out 1 to 6, 1+2, 3+4 or 5+6.

For details, see MIDI Data Format tables <1-6> and <1-7>(MIDI Parameter Change tables),

descriptions on “Output Select”.

The Output Select can be set using the XGworks’ XG Editor Window (The properties dialog

box which opens when clicking on the [DETAIL] button of the part unit). If you are opening

the multi part’s properties dialog box, the Output Select can be set in the General page of

the Detail screen.

SW1000XG-E.qx 4/2/99 4:31 PM Page 12

Installation of the

Driver

To use SW1000XG sound card, the appropriate driver (SW1000XG Windows95 Driver) should be

properly installed in your computer. The driver can be installed from the supplied CD-ROM by

following the steps described below.

n Before installing the driver, make sure that the sound card itself is installed in the computer. (→ P. 10)

n Open the “General” page of the System Properties in your Windows’ Control Panel. If your Windows95 version is

shown as “4.00.950B”, refer to “Installing the driver for Windows95 OSR2 (4.00.950B)”. If your Windows95 version

is shown as “4.00.950” or “4.00.950A”, refer to “Installing the driver for Windows95 (4.00.950 or 4.00.950A)”.

Installing the driver for Windows95 OSR2 (4.00.950B)

1. Turn on the power of your computer. If you turn on it for the first time after installing the

sound card in your computer, the Updated Device Driver Wizard will appear automatically.

2. Insert the supplied CD-ROM in the CD-ROM drive and click [Next]. The message saying

“Windows was unable to locate a driver for this device” will be displayed.

SW1000XG-E.qx 4/2/99 4:31 PM Page 13

3. Click [Other Locations]. Select Other Location dialog box will be displayed.

4. Type the name of the CD-ROM drive (E:\, F:\, etc.) and the folder (Win95drv) in the

“Location” box.

e.g. E:\Win95drv, F:\Win95drv

5. Click [OK]. The message saying “Windows found the following updated driver for this

device” will be displayed.

6. Click [Finish]. Insert Disk dialog box will be displayed.

SW1000XG-E.qx 4/2/99 4:31 PM Page 14

7. Click [OK]. Copying Files dialog box will be displayed.

8. Type the name of the CD-ROM drive and the folder in the “Copy files from:” box, as you did

in step 4.

e.g. E:\Win95drv, F:\Win95drv\

9. Click [OK]. Files will be copied.

10.

Restart the computer.

This completes the installation of the driver.

Installing the driver for Windows95 (4.00.950 or 4.00.950A)

1. Turn on the power of your computer. If you turn on it for the first time after installing the

sound card in your computer, the New Hardware Found window will appear automatically.

2. Insert the supplied CD-ROM in the CD-ROM drive, select “Driver from disk provided by

hardware manufacturer” and click [OK]. Install From Disk dialog box will be displayed.

3. Type the name of the CD-ROM drive (E:\, F:\, etc.) and the folder (Win95drv) in the “Copy

manufacturer’s files from:” box.

e.g. E:\Win95drv, F:\Win95drv

4. Click [OK]. Insert Disk dialog box will be displayed.

5. Click [OK]. Copying Files dialog box will be displayed.

6. Type the name of the CD-ROM drive and the folder in the “Copy files from:” box, as you did

in step 3.

e.g. E:\Win95drv, F:\Win95drv\

7. Click [OK]. Files will be copied.

8. Restart the computer.

This completes the installation of the driver.

SW1000XG-E.qx 4/2/99 4:31 PM Page 15

Installation of the

Software

This package contains software which can bring out full advantage of the SW1000XG sound card,

including MIDI sequence software XGworks for SW1000XG, Wave Editor TWE and various XG

plug-in software.

This section explains you how to install them from the supplied CD-ROM.

Installing XGworks for SW1000XG and Wave

Editor TWE

The following software can be installed by following the steps described below. For information

on each software, see page 7.

• XGworks for SW1000XG

• SW1000XG Mixer

• Wave Editor TWE

n SW1000XG Mixer is a plug-in software for XGworks for SW1000XG, which can control mixing of audio parts when

you record wave data to XGworks’ wave track and/or when you play back XGworks’ wave track.

1. Insert the supplied CD-ROM in the CD-ROM drive.

2. Open “My Computer” by double-clicking its icon.

3. Double-click the CD-ROM icon and then double-click Setup.exe contained in the CD-ROM’s

“XGworks” folder. Welcome dialog box will appear.

SW1000XG-E.qx 4/2/99 4:31 PM Page 16

4. Click [Next]. Software License Agreement dialog box will appear. Read this thoroughly before

moving on to the next step.

5. Click [Yes]. Choose Destination Location dialog box will appear. If you want to change the

destination, click [Browse] and select the destination.

6. Click [Next]. Setup Type dialog box will appear. You can select the type of installation.

n Selecting “Typical” is recommended for most users.

SW1000XG-E.qx 4/2/99 4:31 PM Page 17

7. Click [Next]. Select Components dialog box will appear. You can select the preferred applica-

tion language version.

8. Click [Next]. Select Program Folder dialog box will appear. You can change the folder name

to which the program will be installed.

9. Click [Next]. Files will be copied.

10.

Restart the computer.

This completes the installation of XGworks for SW1000XG, SW1000XG Mixer and Wave Editor TWE.

SW1000XG-E.qx 4/2/99 4:31 PM Page 18

Installing XG Plug-In Software

The following software can be installed by following the steps described below. For information

on each software, see page 7.

• VL Visual Editor

• VH Effect Editor

• DX Easy Editor & DX Simulator

n Before installing the XG plug-in software, make sure that the XGworks for SW1000XG is installed in the computer.

1. Insert the supplied CD-ROM in the CD-ROM drive.

2. Open “My Computer” by double-clicking its icon.

3. Double-click the CD-ROM icon and then double-click Setup.exe contained in the CD-ROM’s

“Plug” folder. Welcome dialog box will appear.

4. Click [Next]. Software License Agreement dialog box will appear. Read this thoroughly before

moving on to the next step.

SW1000XG-E.qx 4/2/99 4:31 PM Page 19

5. Click [Yes]. Before Setup dialog box will appear. Read this thoroughly before moving on to the next step.

6. Click [Yes]. Language dialog box will appear. You can select the preferred application lan-

guage version.

7. Click [Next]. Programs dialog box will appear. You can select which plug-in software to be

installed.

SW1000XG-E.qx 4/2/99 4:31 PM Page 20

Sivu latautuu...

Yamaha SW1000XG Omistajan opas

Merkki: Yamaha

Malli: SW1000XG

Luokka: Synthesizer

Tyyppi: Omistajan opas

Lataa PDF

raportti

muilla kielillä

polski: Yamaha SW1000XG Instrukcja obsługi
Türkçe: Yamaha SW1000XG El kitabı
English: Yamaha SW1000XG Owner's manual
čeština: Yamaha SW1000XG Návod k obsluze
svenska: Yamaha SW1000XG Bruksanvisning
русский: Yamaha SW1000XG Инструкция по применению
italiano: Yamaha SW1000XG Manuale del proprietario
Deutsch: Yamaha SW1000XG Bedienungsanleitung
português: Yamaha SW1000XG Manual do proprietário
dansk: Yamaha SW1000XG Brugervejledning
français: Yamaha SW1000XG Le manuel du propriétaire
español: Yamaha SW1000XG El manual del propietario
Nederlands: Yamaha SW1000XG de handleiding
română: Yamaha SW1000XG Manualul proprietarului

Yamaha SW1000XG Omistajan opas

Yamaha SW1000XG Omistajan opas

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat