Yamaha CRW3200SX Series Ohjekirja

Brändi: Yamaha

Malli: CRW3200SX Series

Kategoria: Optical disc drives

Tyyppi: Ohjekirja

Tämä käsikirja sopii myös

CRW3200SX

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA.

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW3200SX

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.

6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780 – 787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.85 mW (Continuous)

Write Mode: Max. 48 mW

(for 212 ns, Min. Cycle 57.9 ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780 – 787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,85 mW (kontinuierlich)

Schreibmodus: Max. 48 mW

(für 212 ns, Zyklusmin. 57,9 ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780 – 787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,85 mW (continue)

Mode de gravure: max. 48 mW

(pour 212 ns, cycle min. 57,9 ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780 – 787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,85 mW (continua)

Modo de escritura: máx. 48 mW

(para 212 ns, ciclo mínimo 57,9 ns)

OWNER’S MANUAL

English

SAFETY PRECAUTIONS

PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY TO

PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.

These precautions explain how to use the device properly and safely, thereby preventing

injury to yourself and others. This section has been sub-divided into a WARNING section

and a CAUTION section, according to the likelihood and nature of any potential injuries or

damage inflicted. They relate to your personal safety, and also help you prevent the risk

of damage to the device. Please read these sections carefully prior to proceeding.

WARNING

Always follow these basic precautions to avoid short-circuit, damage, fire, or other

hazards, and to avoid serious injury or fatal accident from electrical shock.

● Do not attempt to open or disassemble the device to avoid the risk of electrical shock,

fire, or malfunction.

● Do not look directly at the laser source to avoid the risk of eye damage or blindness.

● Do not insert fingers or foreign objects into the device to avoid the risk of electrical

shock, fire, malfunction, or personal injury.

● Do not expose the device to high humidity or place liquid containers such as a flower

vase on the device to avoid the risk of electrical shock, fire, or malfunction.

● Do not expose the device to temperature outside the range 5 – 35 °C (41 – 95 °F) to

avoid the risk of fire, deformation of the device panel, or malfunction.

● Do not expose the device to dusty place to avoid the risk of fire or malfunction.

● Always follow the owner’s manual to set up or connect the devices properly to avoid

the risk of electrical shock, fire, malfunction, or personal injury.

● If unusual smells, sounds or smoke come from the device, or if foreign objects such

as liquid get into the device, turn off and unplug the computer immediately to avoid

the risk of electrical shock, fire, or malfunction. Contact the store of purchase or your

nearest Yamaha dealer (listed at the back of this manual).

● Be sure that the computer is electrically grounded to avoid the risk of electrical shock.

● Prior to cleaning the drive, always unplug the computer or do not handle the plug with

wet hands to avoid the risk of electrical shock.

● Use the included AC adapter to avoid the risk of fire or malfunction.

iii

● Clean the AC power plug regularly to avoid the risk of fire due to insulation failure

such as humidity.

● Do not unplug the AC adapter by pulling the cable, and do not place objects on the

cable to avoid the risk of electrical shock, fire, or malfunction.

● Plug in the AC adapter fully to avoid the risk of electrical shock or fire.

● Do not connect many devices to an electrical outlet. Maintain the rated power of the

outlet to avoid the risk of fire due to overheating.

CAUTION

Always follow these basic precautions to avoid physical injury to yourself or others,

and damage to the device or other property.

● Always unplug the computer if it will not be used for a prolonged period or if there is a

possibility of lightning, to avoid the risk of electrical shock, fire, or short-circuit.

● Do not use the device near other electrical appliances such as televisions, radios, or

speakers to avoid the risk of interferences between each other.

● Do not place the device unstably to avoid the risk of malfunction or personal injury by

its falling down.

● Do not place the device with a possibility of excessive vibration to avoid the risk of

damage to written data or malfunction.

● Place the device horizontally to avoid the risk of damage to written data.

● Prior to transporting the device, remove the disc from the disc tray to avoid the risk of

damage to written data.

● Use soft, dry cloths to wipe the device. Do not use benzene, paint thinner, detergents,

or chemically treated wiped cloths, and do not place vinyl, plastic, or rubber objects

on the device to avoid the risk of malfunction or damage to the surface of the device.

● Do not rest your weight on or place heavy objects on the device, and do not apply

excessive force to the buttons, switches, or connectors to avoid the risk of damage to

the device or personal injury.

● Be careful not to short-circuit the AC power plug with metal objects to avoid the risk of

malfunction.

● Do not wrap the power cable around the AC adapter to avoid the risk of breaking the

wire or malfunction.

● Do not listen to audio with headphones at high volume for prolonged period to avoid

auditory disorder.

● Prior to turning on the computer, always minimize the volume to avoid auditory

disorder by a sudden burst of sound at high volume.

● Do not place the device near magnets or anything magnetized such as a display to

avoid the risk of interferences between each other.

● Have the device serviced regularly to avoid internal dust buildup that can cause

malfunction, damage or fire. For service information and service charges, contact the

store of purchase or your nearest Yamaha dealer (listed at the back of this manual).

WARRANTY

YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR AS A

RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE MANUAL

THAT COMES WITH THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY DATA CAUSED AS

A RESULT OF USING THIS PRODUCT.

Precautions for Transportation

Transporting the device unfixed may damage its internal mechanism or circuits.

• Remove the disc from the disc tray of the device.

• Put the device in the original box.

Prior to use, check that the complete accessories are included. (Refer to the original box.)

• This document may not, in whole or in part, be copied, photocopied, reproduced, translated,

transmitted, or reduced to any electronic medium of machine readable form without prior consent

in writing from Yamaha.

• Windows is a registered trademark of Microsoft Corporation.

• Apple, Macintosh, and Mac OS are registered trademarks of Apple Computer, Inc.

• SafeBurn™ is a trademark of Yamaha Corporation.

• All other trademarks are the property of their respective companies.

™ and ® marks are not specified in this manual.

Table of Contents

Features of the CRW3200SX Drive................................................ 1

Names and Functions of Parts.....................................................2

Front Panel...............................................................................................2

Rear Panel................................................................................................3

Precautions on Use.................................................................. 4

Handling Discs ........................................................................................4

Disclaimer of Indemnity..........................................................................4

Compatible discs......................................................................................5

System Requirements ..............................................................................6

Preparing the CRW3200SX Drive ................................................. 9

Serial Number..........................................................................................9

1 Set up the CRW3200SX drive.............................................................9

2 Connect the CRW3200SX drive........................................................12

3 Check Recognition of the CRW3200SX Drive.................................16

4 Install CD writing software ...............................................................19

Loading/Ejecting a Disc ...........................................................20

Troubleshooting.....................................................................22

Firmware.............................................................................29

CRW3200SX Drive Specifications................................................30

Technical Notes.....................................................................34

Buffer Underrun Protection Function....................................................34

Writing Methods....................................................................................34

For details about how to install and use the CD writing software, refer to the

documentation that comes with it.

• The information contained in this manual is subject to change without prior notice.

• Reproduction of this manual, either in part or in full, is expressly forbidden.

Features of the CRW3200SX Drive

High speed writing/reading

The CRW3200SX drive supports up to 24X-speed writing for CD-R discs, and up to

10X-speed writing/rewriting for CD-RW discs. In addition, the drive supports data

reading and digital audio data extraction at up to 40X speed.

Tip

• The Partial CAV method permits 24X-speed writing for CD-R discs.

• The CLV method and the 4X – 10X Full CAV method permit 10X-speed writing/

rewriting for CD-RW discs.

SafeBurn™ (Enhanced stability writing technology)

The generous 8 MB buffer memory provides sufficient data storage to enable stable

disc writing at high speeds. Even if data transfer from the computer is interrupted,

Buffer Underrun Protection is activated to save CD-R discs from a writing error.

(P. 34)

“Optimum Write Speed Control” adjusts the writing speed to the optimum rate for

every CD-R disc automatically. You can set the maximum writing speed with your

CD writing software.

• Optimum Write Speed Control can be activated when the maximum writing speed is

set at 12X or more.

• The minimum writing speed to be automatically selected is 8X. Manually set the

optimum writing speed if a writing speed supported by a disc is less than 8X.

High fidelity digital audio

The CRW3200SX drive supports extraction of digital audio data at up to 40X speed

using CD writing software, as well as recording digital audio with high fidelity even

at 24X-speed writing.

Audio Master Quality Recording (High quality audio writing mode)

Audio Master Quality Recording enables you to create high quality audio CDs. This

mode is available for CD-R discs with a capacity of 650 MB and 700 MB. (P. 35)

Audio CDs that are created with Audio Master Quality Recording may not be played

back on certain audio recorders and CD-R/RW drives.

CD-MRW (CD Mount Rainier ReWriting)

CD-MRW is a new standard of packet writing. Compared to the ordinary packet

writing, CD-MRW provides many useful functions such as background formatting.

(P. 35)

Note

Names and Functions of Parts

➀

Disc tray

Holds the disc. It is opened or closed by

pressing the eject button. (P. 20)

➁

Manual eject hole

Forcibly opens the disc tray when the tray

cannot be opened by pressing the eject

button. (P. 21)

➂

Eject button

Press to open or close the disc tray. (P. 20)

➃

Headphone jack

Connects headphones or external speakers

to the drive; has stereo mini-jack

specifications.

➄

Headphone volume dial

Controls the volume of the headphones.

The volume increases as the dial is turned

to the right.

➅

LED

Indicates the operational status of the

CRW3200SX drive by its colors and

blinking patterns.

Lights or blinks blue

• Lights: Standby (with disc)

• Blinks: Opening/Closing disc tray, or

reading disc information (TOC)

• Blinks rapidly: Playback audio

• Blinks irregularly: Reading data

Lights or blinks purple

• Lights: Standby (no disc) or the disc tray

is open

• Blinks: Accessing for writing or test

writing

• Blinks rapidly: Writing

Blinks orange

• Malfunction

Front Panel

➅

➁

➃➄

➀➂

Names and Functions of Parts

➀

LINE OUT jacks (L/R)

Connect audio devices such as external

speakers.

➁

POWER switch (STANDBY/ON)

Turns the power on/off. (P. 12, 15)

➂

DC-IN connector

Connects the included AC adapter. (P. 14)

➃

SCSI connectors

Connect the SCSI cable. (P. 12)

D-sub half-pitch 50-pin pin-type is used.

(P. 13)

➄

Dip switch

Sets the SCSI ID number and the

terminator. (P. 9)

Rear Panel

➃➄

➁➀

➂

Precautions on Use

To avoid trouble, such as writing errors, loss of recorded data, and malfunction of

the drive, take the following precautions when handling discs.

• Do not place discs in a hot or damp place or where they will be exposed to direct

sunlight.

• Do not touch the disc surface. Hold the disc by the edge when handling it.

• Remove dust and dirt from the disc surface. Use an air spray to remove dust. The

disc surface may be scratched if strongly wiped with a dry cloth.

• Do not stick labels to the disc surface or write anything on it except where

designated.

• Do not clean discs with chemicals or detergents.

• Do not bend or drop discs.

It is prohibited by law to duplicate copyright material for non-personal use without

the prior consent of the copyright holder. When copying material with your CD-R/

RW drive, take due care not to infringe the copyright.

• Yamaha assumes no liability for the loss of any profits incurred as a result of the

loss or corruption of data written on a CD-R or CD-RW, for any loss or damage

caused by or arising out of extraordinary circumstances (including circumstances

that Yamaha has foreseen or could foresee), nor for any damages incurred or

claimed by a third party.

• After handling important data, make a comparison between the original and the

copied data (to confirm that the data has been copied properly).

• In no event shall Yamaha be liable for any damage to discs due to a Buffer

Underrun Error (P. 34) or for any other reason, or the inability to use distributed

discs with your drive.

• Yamaha assumes no liability for the inability to write/playback discs because of

their format.

Handling Discs

Disclaimer of Indemnity

Precautions on Use

Discs that can be written on

The CRW3200SX drive can write on the following discs.

For the latest information about discs previously checked for compatibility with the

drive, refer to the following website.

YAMAHA CD-R/RW Drive website

URL: http://www.yamaha.co.jp/english/product/computer/

Compatible discs

CD-R discs

• The CRW3200SX drive can write at 1X, 2X, 4X, 8X, 12X, 16X or 24X speed.

• CD-R discs can be played back on a CD-ROM drive or a CD player.

• 24X-speed writing is enabled with Partial CAV method. (P. 6)

• Check the writing speeds your disc supports prior to writing.

CD-RW discs

• The CRW3200SX drive can write/rewrite at 2X or 4X speed.

• CD-RW discs can be read/played back on a device (e.g. CD-ROM drive) that

supports “CD-RW” discs.

Some discs support only 2X speed.

High Speed CD-RW discs

• The CRW3200SX drive can write/rewrite at 4X, 8X or 10X speed.

• High Speed CD-RW discs can be read/played back on a CD-RW drive that

bears the High Speed CD-RW logo or a device (e.g. CD-ROM drive) that

supports “CD-RW” discs.

• When using the packet writing method (P. 35) for writing/rewriting onto High

Speed CD-RW discs, you can select the 4X – 10X Full CAV method. For more

information refer to the documentation that comes with your CD writing software.

(Your CD writing software must support the Full CAV method, as does the CD

Writing software that comes with the CRW3200SX drive.)

• The Full CAV method is recommended when opening and editing a file on a CD-

RW disc with an application software.

• In order to write, erase, read or play back High Speed CD-RW discs, use a CD-R/

RW drive that bears the High Speed CD-RW logo. When using a CD-ROM drive

to read/play back High Speed CD-RW discs, use a drive that supports CD-RW

discs.

If these discs are used with a CD-R/RW drive not bearing the High Speed CD-RW

logo, the discs may not be recognized, resulting in a computer not operating

properly or other malfunctions occurring.

Refer to the YAMAHA website below prior to attempting to read/play back these

discs on a YAMAHA CD-R/RW drive not bearing the High Speed CD-RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

Note

Partial CAV (Constant Angular Velocity)

The CLV (Constant Linear Velocity) method is generally used to write data on a CD-R

disc. In writing using the CLV method, the disc rotation speed is adjusted to keep the data

writing speed (data transfer rate) constant on all parts of the disc.

In contrast, the CAV (Constant Angular Velocity) method exercises control so as to keep

the disc rotation speed constant. Since the CAV method makes it possible to substantially

increase the maximum data transfer rate without straining of the drive, it is adopted today

for most CD-ROM drives.

CD formats define the constant linear density of written data so that the amount of written

data per disc rotation will increase as the writing point moves from the inner track to the

outer track.

With the CAV method, therefore, data is transferred at a higher rate when it is written on

the outer tracks of the disc. To achieve 24X-speed writing, the CRW3200SX drive

employs the Partial CAV method, which is a combination of the CAV method for inner

tracks and the CLV method for outer tracks.

The Partial CAV method controls the disc rotation speed so that the CRW3200SX drive

starts writing at 18X speed on inner tracks, increasing the speed to 24X as the read/write

head moves outward and holds the speed at 24X on outer tracks.

Tip

The CRW3200SX drive supports 8 cm discs.

Use only circular discs. Do not use any irregular shaped discs such as heart-shaped or

star-shaped discs to avoid the risk of malfunction.

The CRW3200SX drive is designed to operate in the following computer

environment. If your computer does not meet these requirements, the CRW3200SX

drive may not operate or write at the maximum speed.

For Windows

Computer (PC/AT compatible)

• CPU: Pentium II-class or higher, 300 MHz or faster

• RAM: 32 MB (64 MB or more is recommended)

64 MB or more is required (128 MB is recommended) for Windows 2000

Professional, while 128 MB or more is required (256 MB is recommended) for

Windows XP.

Note

System Requirements

Continued on next page

Precautions on Use

• Hard drive space

Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating an image file, there must be enough free space on the hard drive to store

the image file in addition to the working area (a total of up to 900 MB).

However, hard drive space for image files is not required when directly writing

onto a CD-R/RW disc from a hard drive or CD-ROM using the CRW3200SX

drive (on-the-fly writing).

Image file

You can collect the data files to be written on a CD-R/RW disc into a single image file.

The image file is useful for writing the same data onto multiple discs. For details, refer

to the documentation that comes with the CD writing software.

• A spare PCI expansion slot for a SCSI card (if one hasn’t been installed or built-

in)

• SCSI card

SCSI is a standard to connect a computer and peripheral devices.

An optional SCSI card is required to connect the CRW3200SX drive for the

computer without a SCSI connector.

Adaptec’s AHA-2940 series SCSI cards (for PCI slot) are recommended.

For the latest information about SCSI cards supporting the CRW3200SX drive,

refer to the following websites.

YAMAHA CD-R/RW Drive Website

URL: http://www.yamaha.co.jp/english/product/computer/

Operating system

Windows 95 (OSR2 or later), Windows 98, Windows 98 Second Edition,

Windows Me, Windows 2000 Professional, Windows XP

CD writing software

The CRW3200SX drive requires CD writing software to write onto a CD-R/RW

disc. Use the CD writing software that supports the CRW 3200SX drive.

For details about installing and using the CD writing software, refer to the

documentation that comes with the CD writing software.

For Macintosh

Computer (Macintosh)

• CPU: PowerPC G3, 300 MHz or faster

• RAM: 32 MB (64 MB or more is recommended)

•CD-ROM drive

The CRW3200SX drive cannot be used to boot the computer or to set up an operating

system.

• Hard drive space

Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating image file, there must be enough free space on the hard drive to store the

image file in addition to the working area (a total of up to 900 MB).

However, hard drive space for image file is not required when directly writing

onto a CD-R/RW disc from hard drive or CD-ROM using the CRW3200SX drive

(on-the-fly writing).

Image file

You can collect the data files to be written on a CD-R/RW disc into a single image file.

The image file is useful for writing the same data onto multiple discs. For details, refer

to the documentation that comes with the CD writing software.

• A spare PCI expansion slot for a SCSI card (if one hasn’t been installed or built-in)

• SCSI card

SCSI is a standard to connect a computer and peripheral devices.

An optional SCSI card is required to connect the CRW3200SX drive for the

computer without a SCSI connector.

Adaptec’s PowerDomain 2930 SCSI cards (for PCI slot) are recommended.

For the latest information about SCSI cards supporting the CRW3200SX drive,

refer to the following websites.

YAMAHA CD-R/RW Drive Website

URL: http://www.yamaha.co.jp/english/product/computer/

Operating system

Mac OS 8.1, 8.5, 8.6 and 9 to 9.2 (Classic API with Mac OS X is not supported.)

CD writing software

The CRW3200SX drive requires CD writing software to write onto a CD-R/RW

disc. Use the CD writing software that supports the CRW3200SX drive.

For details about installing and using the CD writing software, refer to the

documentation that comes with the CD writing software.

Note

Preparing the CRW3200SX Drive

The serial number is printed on the label on the bottom of your CRW3200SX drive.

When you have a question about the drive or need user support services, the serial

number is required.

Please write the serial number down in the space below. It may be difficult to check

the serial number after setting up the drive or for any other reason.

Prior to connecting the CRW3200SX drive to the computer, set up the following

using the dip switch on the rear panel of the drive.

➀ SCSI ID Number

➁ Termination

Serial Number

1 Set up the CRW3200SX drive

Serial number

(10 characters: 3 letters +

7 numbers)

ID SELECT

TERMINATOR

124

Rear panel

Dip switch

➀

➀➀

➀ SCSI ID Number

Each of the SCSI devices connected to the computer needs to be identified by its

own SCSI ID number from “0” to “7.” The SCSI ID number “7” is normally

reserved for the SCSI card. Therefore, assigning a SCSI ID number from “0” to

“6,” except for the ID numbers in use by other SCSI devices, to the CRW3200SX

drive is recommended.

The dip switch of the CRW3200SX has four switches, and use SW 1, SW 2, and

SW 3 (three switches from the left) to set the SCSI ID number. The switches are

set to ON when pulled down. Each switch set to ON counts each ID SELECT

number, and the sum total of the ID SELECT number determines SCSI ID number

as the SCSI ID table shown below.

∗ The SCSI ID number “7” is normally reserved for the SCSI card.

• In the case that other SCSI device has been already connected to the computer, be

sure that the CRW3200SX drive’s SCSI ID number is different from other devices’.

The CRW3200SX drive’s SCSI ID number is set at “1” by default.

• Set the dip switch completely upward/downward.

SCSI ID

SW 1

(ID SELECT: 1)

SW 2

(ID SELECT: 2)

SW 3

(ID SELECT: 4)

1 (default) ON

2ON

3ONON

4ON

5ON ON

6ONON

∗

∗∗

∗

ON ON ON

Note

SCSI ID 0 SCSI ID 1

(by default)

SCSI ID 2 SCSI ID 3

SCSI ID 4 SCSI ID 5 SCSI ID 6 SCSI ID 7

∗

∗∗

∗

OFF

Preparing the CRW3200SX Drive

➁

➁➁

➁Termination

A terminator prevents the reflection of SCSI signals at the last device of the SCSI

chain. The terminators of the first and last devices of the SCSI chain should be set

to ON. If the CRW3200SX drive is not at the last of the SCSI chain, the

TERMINATOR (SW 4) of the dip switch should be set to OFF.

The TERMINATOR (SW 4) of the dip switch is set at ON by default.

Note

Computer

Extenal SCSI

Device

(unterminated)

CRW3200SX

(terminated)

SCSI card

(terminated)

Termination ON (by default) Termination OFF

Set to ON if the CRW3200SX drive

is the last of the SCSI chain

Set to OFF if the CRW3200SX drive

is not the last of the SCSI chain

OFF

Turn off the computer and all peripheral devices.

Check that the power switch on the rear panel of the

CRW3200SX drive is turned off (STANDBY).

Connect the SCSI cable to either one of the SCSI connectors on

the rear panel of the CRW3200SX drive.

Connect the other end of the SCSI cable to the SCSI card

connector of the computer or the other SCSI device.

2 Connect the CRW3200SX drive

SCSI connector

SCSI card

connector

CRW3200SX

rear panel

SCSI cable

Sivu latautuu ...

Yamaha CRW3200SX Series Ohjekirja

Brändi: Yamaha

Malli: CRW3200SX Series

Kategoria: Optical disc drives

Tyyppi: Ohjekirja

Tämä käsikirja sopii myös

CRW3200SX

Lataa PDF

raportti

muilla kielillä

Türkçe: Yamaha CRW3200SX Series Kullanım kılavuzu
English: Yamaha CRW3200SX Series User manual
svenska: Yamaha CRW3200SX Series Användarmanual
italiano: Yamaha CRW3200SX Series Manuale utente
Deutsch: Yamaha CRW3200SX Series Benutzerhandbuch
dansk: Yamaha CRW3200SX Series Brugermanual
français: Yamaha CRW3200SX Series Manuel utilisateur
Nederlands: Yamaha CRW3200SX Series Handleiding
română: Yamaha CRW3200SX Series Manual de utilizare

Liittyvät paperit

Muut asiakirjat

Sony LIB-D81 Ohjekirja