Yamaha CRW2200IX Omistajan opas

Yamaha
Merkki
Yamaha
Malli
CRW2200IX
Luokka
Optical disc drives
Tyyppi
Omistajan opas

Tämä ohje sopii myös

CRW2200IX (W)
4th draft
2001.06.22
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation, USA.
Address: 6660 Orangethorpe Avenue
Buena Park, CA 90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW2200IX
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.
6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Product Class: Class 1
Laser Diode Properties
Wavelength: 780-787 nm
Pulse Durations and Max. Output
at the lens of the Laser Pickup Unit
Read Mode: 0.7mW (Continuous)
Write Mode: Max. 38mW
(for 166ns, Min. Cycle 86.6ns)
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
Laserprodukt-Klasse: Klasse 1
Eigenschaften der Laserdiode
Wellenlänge: 780-787 nm
Impulsdauer und max. Ausgang an der Linse der
Laser-Abtasteinheit
Lesemodus: 0,7mW (kontinuierlich)
Schreibmodus: Max. 38mW
(für 166ns, Zyklusmin. 86,6ns)
Classe du produit laser: Classe 1
Caractéristiques de la diode laser
Longueur d’onde: 780-787 nm
Durée des impulsions et sortie maximum depuis
la lentille du bloc capteur optique
Mode de lecture: 0,7mW (continue)
Mode de gravure: max. 38mW
(pour 166ns, cycle min. 86,6ns)
Clase de producto láser: Clase 1
Propiedades del diodo láser
Longitud de onda: 780-787 nm
Duración del pulso y potencia de salida máxima
en el objetivo de la unidad captora láser
Modo de lectura: 0,7mW (continua)
Modo de escritura: máx. 38mW
(para 166ns, ciclo mínimo 86,6ns)
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
DANGER - VISIBLE AND / OR INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
COMPLIES WITH 21 CFR CHAPTER1, SUBCHAPTER J.
i
OWNER’S MANUAL
English
ii
PLEASE READ THE FOLLOWING WARNING AND
PLEASE READ THE FOLLOWING WARNING AND PLEASE READ THE FOLLOWING WARNING AND
PLEASE READ THE FOLLOWING WARNING AND
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
SAFETY AND PREVENT DAMAGE TO THE DEVICE.
SAFETY AND PREVENT DAMAGE TO THE DEVICE.SAFETY AND PREVENT DAMAGE TO THE DEVICE.
SAFETY AND PREVENT DAMAGE TO THE DEVICE.
These precautions explain how to use the device correctly and safely, thereby preventing injury to
yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION
section, according to the likelihood and nature of any potential injuries or damage inflicted. They relate
to your personal safety, and also help you minimize the risk of damaging the device. Please read these
sections carefully before proceeding.
WARNING
Always follow these basic precautions to prevent short-circuit, damage, fire, or other hazards,
and to prevent serious injury or death from electrical shock. These precautions include, but are
not limited to, the following:
● To avoid risk of electrical shock or fire, do not attempt to open or disassemble the device.
● To avoid risk of eye damage or blindness, do not look inside the device.
● To avoid the risk of personal injury or electrical shock, do not insert your fingers, or foreign objects
into the device.
● To avoid the risk of electrical shock, fire, or personal injury, do not expose the device to rain, use it
near water, or in damp or wet conditions, or place containers that contain liquids (they may spill into
the unit) on the device.
● To avoid risk of personal injury, electrical shock, fire, or damage to the unit, follow the Owner’s
Manual carefully.
● If unusual smells, sounds or smoke come from the device, turn off the computer immediately to
avoid the risk of electrical shock, fire or damage to the device, and return the device to the place of
purchase, or alternatively, to your nearest Yamaha dealer (listed at the back of this manual).
● Make sure the computer is electrically grounded to avoid the risk of electrical shock.
● Always unplug the computer from the electrical outlet, and do not touch the plug with wet hands, as
there is an increased risk of electrical shock.
● The drive should not be exposed to temperatures outside the range 5 – 35 °C (41 – 95 °F) to avoid
risk of malfunction, fire or personal injury.
● To avoid the risk of electrical shock or fire, be sure to use the correct voltage rating.
● Clean the AC power plug regularly, especially the blades, to avoid the risk of insulation failure or fire
due to humidity.
● Do not pull on the cord itself when disconnecting from the electrical outlet, or let objects rest or roll
over the cord, as the cord can be damaged and cause electrical shock or fire.
SAFETY PRECAUTIONS
iii
● Insert the AC plug firmly, as a poor connection can result in electrical shock or fire.
● Only use the included AC adapter, as malfunction or fire may result.
● Do not connect too many devices to a single electrical outlet, or use voltages exceeding the rated
voltage as this may cause overheating and fire.
CAUTION
Always follow these basic precautions to prevent physical injury to yourself or others, or damage
to the instrument or other property.
● To avoid the risk of electrical shock or fire, always unplug the computer from the electrical outlet if it
will not be used for a prolonged period of time, or if there is a risk of lightning.
● Do not expose the device to excessive vibration, heat, cold or dust, as doing so may result in damage
to the unit’s front panel or its internal components.
● Do not use the device near other products such as televisions, radios, or speakers as this may cause
interference, which can affect the proper operation of the device or other devices.
● To avoid damage to the device or personal injury, always place the device in a stable position.
● Always place the device horizontally (see Owner’s Manual) to avoid the risk of lost written data.
● Always remove any disc from the disc tray before transporting the device as written data may be lost.
● Use a soft, dry cloth to wipe the device. Do not use benzene, paint thinners, detergents, or
chemically treated wiping cloths as these may damage the unit.
Do not place vinyl, plastic, or rubber objects on the device as chemical reactions can cause damage
to the device.
● Do not rest your weight on or place heavy objects on the device, or use excessive force on the
buttons, switches or connectors, as damage to the unit or personal injury may occur.
● Do not listen to audio with headphones at high volume for prolonged periods of time as your hearing
may be damaged as a result.
● Before using the device, always turn down the volume as sudden bursts of sound can result in
hearing damage.
● Do not place the device anywhere near sources of magnetic interference as operational stability may
be adversely affected.
● Have the device serviced regularly (about once a year) to avoid internal dust buildup that can cause
malfunction, damage or fire. For service information, contact the store of purchase, or your nearest
Yamaha dealer (listed in the back of this manual).
● Do not allow the plug of the AC adapter to come into contact with metal as a short circuit can result
and cause a malfunction or damage to the device.
● Do not wrap the power cord around the AC adapter as it may become disconnected and cause a malfunction.
iv
■ About handling CD-R/RW discs
1. Do not store discs in areas subject to excessive humidity or heat (i.e., in direct sunlight or
near a heater).
2. Do not touch the surface of a disc.
When handling a disc, hold it by the edges.
3. Remove dust and dirt from the surface of a disc.
Use an air-blower (i.e., camera lens blower) to remove dust. The surface of a disc may be
scratched if wiped with a dry cloth.
4. Do not stick labels on the surface of a disc.
5. Do not write on the surface of a disc except where indicated.
6. Do not clean discs with chemicals or detergents.
7. Do not bend or drop discs.
8. Use only circular discs. Do not use irregularly shaped discs, such as star, heart or card
shaped, etc., as these could damage your new CD-R/RW drive.
■ Precautions for Transportation
Before transporting the device, always put it in its original box. If the device is transported
without adequate packing, the internal components may be damaged and cause the device
to malfunction.
■ Copyrights
When writing to a CD-R/RW, make sure that you do not infringe on any copyrights. It is
illegal to copy audio CDs for non-personal use. When backing up software, make sure that
you do not infringe on any software copyrights for that product.
■ WARRANTY
YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA
OR ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS
RECOMMENDED THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN
TO. FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND ITS
SUPPLIERS GUARANTEE THE RELIABILITY OF THE DISCS.
1. The information contained in this manual is subject to change
without prior notice.
2. All trademarks contained in this manual belong to their respective
owners.
3. Yamaha does not bear any responsibility for a problem that occurs
as a result of any operations carried out other than those stated in
the manual included with the drive.
4. Reproduction of this manual, either in part or in full, is expressly
forbidden.
v
Table of Contents
Introduction........................................................................ 1
Features of the CRW2200IX Drive.................................................... 1
Before Use ......................................................................... 4
System Requirements.......................................................................... 4
Supported Discs................................................................................... 6
Serial Number ..................................................................................... 8
Front and Rear of Unit............................................................ 9
Front Panel .......................................................................................... 9
Rear Panel ......................................................................................... 10
Setup Procedures ................................................................11
Windows Users ................................................................................. 11
Macintosh Users................................................................................ 12
Install the CD Writing Software........................................................ 13
Set Up the CRW2200IX Drive......................................................... 13
Configuring for the Operating System.............................................. 18
Operation..........................................................................20
Connecting and Disconnecting IEEE1394 Devices.......................... 20
Loading a Disc .................................................................................. 21
Ejecting a Disc .................................................................................. 21
Ejecting a Disc in an Emergency ...................................................... 22
Troubleshooting..................................................................23
Appendix...........................................................................28
Connecting Multiple IEEE1394 Peripherals Together...................... 28
Writing Modes................................................................................... 30
About the Firmware .......................................................................... 32
LED Indicator Messages................................................................... 33
CRW2200IX Specifications............................................................. 34
Index.................................................................................................. 37
©2001 YAMAHA CORPORATION. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted, or reduced to any electronic medium of machine readable
form without prior consent in writing from Yamaha.
Windows is a registered trademark of Microsoft Corporation.
Apple, Macintosh, Mac OS, and FireWire are registered trademarks of Apple
Computer, Inc.
SafeBurn™ is a trademark of Yamaha Corporation.
All other trademarks are the property of their respective companies.
1
Introduction
High speed writing/reading
The CRW2200IX drive supports up to 20X-speed writing of CD-R discs,
*1
and up to
10X-speed writing/rewriting of CD-RW discs.
*2
Furthermore, the drive supports data
reading and digital audio data extraction at up to 40X speed.
Easy setup
Implementation of an IEEE1394 interface (also known as FireWire or i.LINK)
eliminates the need for drive configurations (device ID, termination, etc.). You can
connect and start using the drive whenever you wish without restarting your
computer.
SafeBurn™ (Enhanced write stability technology)
Generous 8MB of buffer memory
Because of the large data storage area, stable disc writing is possible even at fast
speeds.
Buffer Underrun Protection
When data transfer from the host PC is interrupted, Buffer Underrun Protection is
activated to keep precious CD-R discs from going to waste. (
→
P. 3)
Optimum Write Speed Control
Before writing to a CD-R, the CRW2200IX drive checks the disc’s capability and
automatically selects the optimum writing speed
*3
for greater reliability. Even if the
writing speed of the CD-R disc you are using is faster than the setting speed on the
writing software, the setting speed still takes precedence.
Reliable writing
Yamaha’s proprietary Pure-Phase Laser System (patent applied for)
This technology reduces phase interference of the laser beam, so that it projects
accurately onto the disc. Jitter value, an important measure of recording quality, has
been improved 25% compared with Yamaha models not using this technology.
Running OPC (Optimum Power Control)
Running OPC automatically adjusts the output of the laser according to the
characteristics of the disc being used. Running OPC provides greatly enhanced
recording reliability for various manufacturer’s discs.
Features of the
CRW2200IX
Drive
Introduction
2
High-fidelity digital audio
The CRW2200IX drive supports extraction of digital audio data at up to 40X speed,
as well as the recording of digital sound with complete fidelity even when writing at
20X speed.
CD TEXT support
Information such as the song name or artist name can be recorded on Audio CDs
using CD creation software. The text data on the created disc can be displayed on a
CD player that is compatible with the CD TEXT format.
*1 16X- or 20X-speed writing is enabled with the Partial CAV method. (
→
P. 7)
*2 10X-speed writing/rewriting is enabled with the CLV method and the 4X-10X Full CAV method. (
→
P. 8)
*3 The optimal writing speed automatically selected will be between 8X speed and the maximum speed designated
for that disc. If the disc is rated at lower than 8X speed writing, you need to designate the most suitable writing
speed manually.
About IEEE1394
IEEE1394 is an industry standard approved by IEEE (Institute of Electrical and
Electronics Engineers). The serial interface has a broad bandwidth and is fast
enough to transfer large amounts of digital video and audio data bi-directionally
between electronic devices including computer peripherals. Also known as
FireWire and i.LINK, the IEEE1394 interface allows units to transfer data or
various controls over a single IEEE1394 interface cable. Unlike legacy serial
interfaces such as RS-232C, IEEE1394 allows for daisy-chaining devices (serial
connection) with data transfer possible between any two devices on the chain.
IEEE1394 also supports a tree (parallel) connection of devices. In addition to
this flexibility, IEEE1394 also eliminates the need for complicated settings such
as device ID and termination as found with SCSI (Small Computer System
Interface) type interfaces. As of this writing, IEEE1394 supports three different
data transfer rates: 100 Mbps, 200 Mbps, and 400 Mbps.
Introduction
3
Buffer Underrun Defined
CD-R/RW drives are equipped with buffer memory. This memory temporarily
stores data while a disc is being recorded. When buffer memory becomes empty
(due to unexpected interruptions or the system’s inability to keep up with the
writing process), a writing error occurs. This error is known as a “buffer
underrun error.”
A Buffer Underrun Error will permanently ruin the disc.
Yamaha Buffer Underrun Protection
Buffer Underrun Protection is featured in Yamaha’s CRW2200 series CD-R/
RW drives. When a buffer underrun is about to occur, a buffer underrun error is
prevented by temporarily suspending the writing process. Writing resumes when
enough data has accumulated again in buffer memory. Buffer Underrun
Protection on the CRW2200 series is extremely accurate, resulting in seamless
recording between stop and continuation points.
Yamaha Buffer Underrun Protection ensures error-free results.
Test-writing for Buffer Underrun
You can run a check for the likely occurence of Buffer Underrun by Test-writing a CD-RW
disc. The occurrence of a Buffer Underrun depends on your computer system and the CD-R/
RW drive.
Most writing software includes test-writing functions to check the likely occurrence of
Buffer Underrun before actually writing the disc.
Buffer Underrun Protection is set to ON by default. Test-writing is not available in this
setting. To use test-writing with your computer system, the Buffer Underrun Protection
should be set to OFF. (For more details, refer to the documentation that came with your CD
writing software.)
➀➁➂
Data
If data transfer is
interrupted...
Data is stored in
buffer memory...
then buffer memory
begins to empty
When no data is left
in buffer memory...
(Buffer Underrun)
and then written
to disc
writing fails
(Buffer Underrun
Error)
➀➁
If data transfer is
interrupted...
Even if data transfer is interrupted at
any time, it will resume seamlessly...
and buffer memory is
about to empty...
and enough data has accumulated
in buffer memory...
writing is suspended writing resumes
4
Before Use
In order to use the CRW2200IX drive, your computer system will need to meet the
following requirements.
Notes
• The CRW2200IX drive may not write at the maximum speed depending on your computer’s
system configuration.
• For best performance, refer also to the CD writing software documentation for system
requirements (e.g., hardware, OS, etc.).
Windows Users
Computer
• PC/AT-compatible computers
• CPU: Pentium II, 300 MHz or faster.
•RAM: 64 MB or more.
• IEEE1394 port: At least one IEEE1394 port is required.
Note
This port may be a built-in (onboard) type, or provided with a PCI expansion card or a CardBus
card. If you newly install an IEEE1394 PCI or CardBus interface card, your computer should have
an empty PCI expansion slot or a CardBus slot. For more information about the IEEE1394
interface card, refer to “IEEE1394 Interface Card (PCI or CardBus)” shown below.
Operating System (OS)
Windows 98 Second Edition, Windows Me, Windows 2000 Professional
CD-ROM Drive
You may need another CD-ROM drive for any CD-related operations (playback
of an audio CD, installation from CD-ROM, etc.) until you verify that the
CRW2200IX drive is successfully installed. Also you may need another CD-
ROM drive if you are planning to copy a CD-ROM directly to a CD-R/RW disc
on the CRW2200IX drive.
Note
The CRW2200IX drive cannot be used to install an operating system or to boot your
computer from a CD-ROM containing an operating system.
IEEE1394 Interface Card (PCI or CardBus)
For the CRW2200IX drive to work properly with your computer, your IEEE1394
interface card must be OHCI compliant. As of this writing, Yamaha has verified
compatibility with the following cards:
System Requirements
Manufacturer Product Card Type
Advansys ASB30400 PCI
SIIG NN2603 PCI
Before Use
5
Notes
• For the latest information about approved IEEE1394 interface cards, check the YAMAHA
CD-R/RW Drive web site.
URL: http://www.yamaha.co.jp/english/product/computer/
• Some IEEE1394 interface cards may not work properly with your computer. Be sure to
check for compatibility not only with your computer, but also with the CRW2200IX drive
before purchasing a new IEEE1394 interface card.
• Even if you already have an IEEE1394 interface card installed and working properly in
your computer, it may not be compatible with the CRW2200IX drive. Refer to the
requirements listed on the previous page and to your interface card documentation to check
for compatibility.
Macintosh Users
Computer
• Macintosh computers with a built-in FireWire port
• CPU: PowerPC G3, 300 MHz or faster.
• RAM: 64 MB or more.
Operating System
Mac OS 8.6, 9, 9.1 (Except for Classic with Mac OS X)
Note
FireWire software version 2.2.2 or later is recommended for the CRW2200IX drive to work
properly. The latest software is available from the Apple support web site.
CD-ROM Drive
You may need another CD-ROM drive for any CD-related operations (playback of an
audio CD, installation from CD-ROM, etc.) until you verify that the CRW2200IX
drive is successfully installed. Also you may need another CD-ROM drive if you are
planning to copy a CD-ROM directly to a CD-R/RW disc on the CRW2200IX drive.
Note
The CRW2200IX drive cannot be used to install an operating system or to boot your
computer from a CD-ROM containing an operating system.
CD Writing Software
The CRW2200IX drive requires a CD writing software to write onto a CD-R/RW disc.
Make sure your CD writing software supports the CRW2200IX drive.
Note
For details about how to install and use the software, refer to the documentation that came with it.
Hard Drive Space
When writing to a CD-R/RW disc, you will need a working area (50 to 100 MB of
free space) on the hard drive. If you want to create an image file containing all the
data to be written to the CD-R/RW disc, in addition to the working area, you will
need as much hard drive space as that data (up to 900 MB in total). However, this
additional hard drive space for the image file is not needed when you are writing
directly from a hard drive or CD-ROM drive, etc. (on-the-fly writing).
About disk image files
You can collect data files into a single disk image file for a CD-R/RW disc. Also, note that an
image file is useful when writing multiple discs with the same content. For further details, refer to
the documentation that came with your CD writing software.
Before Use
6
The CRW2200IX drive can write to discs that carry the following logos:
*1 Compatible with Orange Book Part 2.
*2 Compatible with Orange Book Part 3 Vol. 1.
*3 Compatible with Orange Book Part 3 Vol. 2.
Note
To find current information about approved discs for the drive, visit the YAMAHA CD-R/RW
Drive web site.
URL: http://www.yamaha.co.jp/english/product/computer/
Supported Discs
CD-R discs
*1
The CRW2200IX drive can write to these discs at 1X, 2X, 4X, 8X, 12X, 16X,
or 20X speed. These discs can be played back in a CD-ROM drive or a CD
player.
Notes
• 16X- or 20X-speed writing is enabled with Partial CAV method. (
→
P. 7)
• For 8X or faster writing, use CD-R discs that match their respective writing
speeds.
CD-RW discs
*2
There are two types of CD-RW discs: those that support write/rewrite speeds
of 1X, 2X, and 4X, and those that support only 2X. The CRW2200IX drive
can write/rewrite at 2X or 4X speed on the first type of disc, and at 2X on the
second type of disc. These discs can be read/played on a device (e.g., CD-
ROM drive) that supports “CD-RW.”
High Speed CD-RW discs
*3
These discs allow writing/rewriting at 4X to 10X speeds. The CRW2200IX
drive can write/rewrite these discs at 4X, 8X, or 10X speed. These discs can be
read/played by a CD-RW drive that bears the High Speed CD-RW logo, or by
a device (e.g., CD-ROM drive) that supports “CD-RW.”
Note
10X-speed writing/rewriting is enabled with the CLV method, and the 4X-10X
Full CAV method. (
→
P. 8)
• In order to write, erase, or read these discs using a CD-R/RW
drive, a drive bearing the High Speed CD-RW logo must be
used. When using a CD-ROM drive to read these discs, the
drive must be capable of reading CD-RW discs.
• If these discs are used in a CD-R/RW drive not bearing the
High Speed CD-RW logo, the discs may not be recognized,
resulting in the computer not operating correctly or other
malfunctions occurring.
• Refer to the page at the URL below before attempting to read
these discs on a Yamaha CD-R/RW drive not bearing the
High Speed CD-RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
Before Use
7
About the Orange Book
The Orange Book standard defines how all recordable discs (including CD-R and CD-RW) are
written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to CD-RW discs.
The standard was named after the color of the book’s cover.
About CD-ROMs
A CD-ROM disc is a compact disc containing high-density read-only data. It has
many applications, including the playback of music and video, the archiving of
data, as well as on-line documentation. The following are descriptions of each
CD-ROM format:
CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a
sampling rate of 44.1 kHz for a 79 minute disc.
Data CD: Up to 700 megabytes of computer data is stored in standard ISO9660
format for a 700 MB disc.
Video CD: These hold movies in which video and audio data has been
compressed using MPEG-1 technology.
About Partial CAV (Constant Angular Velocity)
Writing to a CD-R disc is normally done using the CLV (Constant Linear
Velocity) method. In this method, the disc rotation speed is adjusted so as to
keep a constant data transfer rate at any portion of the disc. In other words, the
disc rotation speed will vary in CLV writing.
In contrast, the CAV (Constant Angular Velocity) method uses a constant disc
rotation speed for all portions of the disc so that the data transfer rate will vary.
Because the CAV method has the advantage of largely increasing the data
transfer rate with a minimum load to the drive’s mechanism (compared to CLV’s
rotation speed adjustment), many current CD-ROM drives use the CAV method.
CD formats define the constant linear density of written data (data should be
written onto the disc at a constant pitch) so that the amount of recorded data per
disc rotation will increase as the writing point moves from the inner to the outer.
In other words, in CAV writing, the outer portion has an increased data transfer
rate.
The CRW2200IX drive uses the CAV method in the inner portions as well as
the CLV method in the outer portions (Partial CAV) in order to enable up to
20X-speed writing. The drive will control the disc rotation speed to start writing
at 12X speed in the inner portions, gradually accelerating up to 20X speed and
maintaining 20X speed in the outer portions.
Before Use
8
Once you have taken the CRW2200IX drive out of its packaging, you should
immediately note down the serial number found at the bottom of the drive with the
bar code. You may need to refer to this number when requesting Customer Support
services. In the box below the following diagram, write down the 10-character serial
number (consisting of 3 letters followed by 7 digits).
About 10X-speed writing/rewriting of a High Speed CD-RW disc
10X-speed writing/rewriting of a High Speed CD-RW disc is enabled with the
CLV method, and the 4X-10X Full CAV method. Commonly, writing/rewriting
is enabled with the CLV method. When writing/rewriting with packet writing
(
→
P. 31), you can also select the Full CAV method. For more details, refer to the
documentation that came with your CD writing software. (Make sure that your
CD writing software supports the Full CAV method.) For direct editing of a file
on a CD-RW disc, the Full CAV method is recommended.
Serial Number
Serial No.
Serial number
(3 letters and 7 digits)
9
Front and Rear of Unit
➀
➀➀
➀
Power LED
Lights up in green when the power of the drive is turned on.
➁
➁➁
➁
Disc tray
The disc tray is used to hold the disc. It slides out from the drive unit when a disc needs to
be loaded or unloaded. (
→P. 21)
➂
➂➂
➂
Manual eject hole
Only use this if no other method is available for unloading a disc. (→P. 22)
➃
➃➃
➃
Eject button
Press this button when you need to open or close the disc tray. Remove the disc after the
disc tray has opened. (
→P. 21)
➄
➄➄
➄
Headphone jack
You can connect stereo headphones to this stereo mini jack and listen to an audio CD
loaded in the drive.
➅
➅➅
➅
Headphone volume control
Adjust this control to set a suitable volume level when listening to an audio CD using the
headphone jack. Slide the knob to the left to decrease the volume and to the right to
increase it.
➆
➆➆
➆
LED
Indicates the operation status of the CRW2200IX drive. (→P. 33)
Front Panel
➃➁➂➀
➄➅ ➆
Front and Rear of Unit
10
➀
➀➀
➀
LINE OUT jacks (L/R)
To listen to audio CDs with the CRW2200IX drive, connect these to the line level input
(LINE IN) of the stereo equipment with a standard stereo phono cable (sold separately).
➁
➁➁
➁
Power switch (STANDBY/ON)
Turns the power on or off. (→P. 13, 15)
➂
➂➂
➂
DC-IN connector
Insert the included AC adapter connector. (→P. 13)
➃
➃➃
➃
IEEE1394 ports
Insert the connector of the IEEE1394 cable here. (→P. 16, 17)
Rear Panel
➃
➁➀➂
11
Setup Procedures
This flowchart shows the procedure for setting up the CRW2200IX drive.
For easy cross-referencing, the relevant pages in this manual are given.
Windows Users
Do you have an appropriate IEEE1394
interface card?
The card should be compatible with your
computer.
Does your computer have a
built-in IEEE1394 port?
STEP
1
Install the CD writing software.
Before installing the software, disconnect
all IEEE1394 devices.
STEP
2
Make sure that system configuration
(CPU, RAM, OS, etc.) of your computer
meets the requirements of the
CRW2200IX drive (→
→→
→P. 4, 5).
Set up the CRW2200IX drive
(→
→→
→P. 13 – 17).
1 Turn your computer and the drive both
on before connecting.
2 Connect your computer and the drive
using the IEEE1394 interface cable that
came with the drive.
You may need a different cable
depending on the IEEE1394 port
connector on your computer (→
→→
→P. 17).
Make sure that the
CRW2200IX drive is correctly
recognized (→
→→
→P. 18).
Start using the CRW2200IX drive
Use the drive to create an audio CD, to backup data
on your hard drive, or for whatever purpose suits
your needs.
Install the card to your
computer.
Read the documentation that
came with the card and properly
set up your computer.
Purchase an IEEE1394 card.
See page 3 for more information about
approved IEEE1394 interface cards that have
been tested for compatibility with the
CRW2200IX drive.
STEP
3
STEP
4
No
YES
No
YES
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
Sivu latautuu...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49

Yamaha CRW2200IX Omistajan opas

Yamaha
Merkki
Yamaha
Malli
CRW2200IX
Luokka
Optical disc drives
Tyyppi
Omistajan opas
Tämä ohje sopii myös
Lataa PDF
raportti

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat