Yamaha PC2001N Omistajan opas

Brändi: Yamaha

Malli: PC2001N

Kategoria: Audio amplifiers

Tyyppi: Omistajan opas

POWER AMPLIFIER

Owner’s Manual

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol within

an equilateral triangle is intended to alert the user to

the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufﬁcient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers)

that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table speciﬁed by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

(5)-2

1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the device, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the device inspected by

qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• If several of the devices are mounted in an EIA-compliant rack, carefully read the

section “Rack Mounting” on page 10.

• Do not use the device in a conﬁned, poorly-ventilated location. If this device is

to be used in a small space other than an EIA-standard rack, make sure that

there is adequate space between the device and surrounding walls or other

devices: at least 10cm at the sides, 20cm behind and 20cm above. Inadequate

ventilation can result in overheating, possibly causing damage to the device(s),

or even ﬁre.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the front and rear to

prevent the internal temperature from becoming too high. In particular, do not

place the device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Doing so may result in noise, both in the device

itself and in the TV or radio next to it.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-2

2/2

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Use only speaker cables for connecting speakers to the speaker jacks. Use of

other types of cables may result in ﬁre.

• Be sure to connect to a properly grounded power source. A ground screw is

provided on the rear panel of this device for maximum safety and shock

prevention. If the mains outlet is not grounded, be sure to connect the ground

screw to a conﬁrmed ground point before plugging the device into the mains.

Improper grounding can result in electrical shock.

• When turning on the AC power in your audio system, always turn on the device

LAST, to avoid speaker damage. When turning the power off, the device should

be turned off FIRST for the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings on the device

(vents, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents, etc.) If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualiﬁed Yamaha service personnel.

• Do not use the device for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• Do not use this device for any purpose other than driving loudspeakers.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product during operation.

Company names and product names used in this Owner’s Manual are trademarks or registered trademarks of their respective owners.

Connections Handling caution

Use only Neutrik NL4FC plugs for connecting Speakon connectors.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device.

Introduction

Thank you for purchasing a Yamaha PC9501N, PC6501N, PC4801N, PC3301N, or PC2001N Series Power

Ampliﬁer.

The PC Series of power ampliﬁers was developed from Yamaha’s wealth of experience in building PA

equipment and its tradition of careful attention to every detail of circuit design. These power ampliﬁers feature

high power and superb quality together with superior reliability and stability, guaranteeing the highest

possible audio performance.

Main features include

• Three modes are provided to support a broad range of applications: STEREO mode which can be driven by

two independent sources, PARALLEL mode in which a monaural source drives both channels, and BRIDGE

mode in which the two internal amps function as a single mono amp.

• Balanced XLR connector and Euroblock connector inputs, and Speakon connector and ﬁve-way binding

post outputs are provided.

•A high pass ﬁlter switch that cuts frequencies below 20 Hz, and detented attenuators and level meters for

channels A and B are provided.

• Metering and indicators include easily visible two-channel level meters, a PROTECTION indicator that

shows the state of various protection systems (power on/off detection, output protection, DC detection), a

TEMP indicator that indicates heat sink overheating, and a REMOTE indicator that indicates the external

remote status.

•Variable-speed low-noise fans ensure high reliability.

• The PC3301N enables parallel connection of multiple high-impedance speakers that support 100 V line

output.

• An optional external amp control device, such as the ACD1 or ACU16-C, enables you to monitor or control

the ampliﬁer via a network. For the latest information about amp control devices, please visit our website:

http://www.yamahaproaudio.com/

This Owner’s Manual applies to the PC9501N, PC6501N, PC4801N, PC3301N, and PC2001N power

ampliﬁer. In order to take full advantage of your power ampliﬁer and enjoy long and trouble-free operation,

please read this Owner’s Manual carefully before using your Power Ampliﬁer.

Contents

Introduction ............................................................ 5

Controls and Functions......................................... 6

Front Panel.......................................................... 6

Rear Panel .......................................................... 7

Speaker connections........................................... 8

Connection ............................................................. 9

Using a Euroblock connector .............................. 9

Speaker Connection............................................ 9

Air Flow ................................................................. 10

Rack Mounting ..................................................... 10

Specifications....................................................... 11

General Specifications ...................................... 11

Block Diagram................................................... 12

Dimensions ....................................................... 13

Troubleshooting................................................... 14

Current Draw ........................................................ 14

Controls and Functions

■

Front Panel

POWER/STAND-BY switch and indicator

This turns the power of the ampliﬁer on/off. When you

press the switch to turn on the power, the indicator will

light green.

If the ampliﬁer is connected to an amp control device

ACD1 or ACU16-C and the ampliﬁer has been

commanded to enter STAND-BY mode, this indicator

will light orange.

REMOTE indicator

This indicator will light green if the ampliﬁer is being

controlled from an external device connected to the

DATA port located on the rear panel.

PROTECTION indicator

This indicator lights up red when the protection circuit

is operating. During this time, the amp will be

disconnected from the speaker system, and no sound

will be output from the speaker.

The protection system activates in the following

situations:

• When the ampliﬁer is turned on

The protection system activates for approximately ten

seconds when the ampliﬁer is turned on. After ten

seconds, the protection system deactivates

automatically and the ampliﬁer is ready for normal

operation.

• If a DC voltage is detected at the ampliﬁer’s outputs

Turn off the power, and then turn the power back on

again.

• If the ampliﬁer overheats

When this occurs, the TEMP indicator will be lit.

You should turn off the ampliﬁer and allow it time to

cool down. See the Precautions section of this Owner’s

Manual for ways to prevent the ampliﬁer overheating.

TEMP indicator

This indicator will light red if the heat sink temperature

exceeds 85 degrees Celsius.

Level meters

These are nine-segment level meters that indicate the

output level of output jacks A and B. If the distortion of

the output signal exceeds 1%, the red CLIP indicator

will light.

Volume knobs

These are detented volume knobs that attenuate the

input signals of channels A and B over a range of –

∞

– 0 dB.

In BRIDGE mode, only the channel A knob is used.

Air intakes

The ampliﬁer has a forced-air cooling fan that takes in

air from the front and exhausts it from the rear. You

must make sure that these intakes are not obstructed.

Security cover

If you want to keep the volume settings from being

modiﬁed, attach the included security cover using the

screw holes shown below, so that the volume controls

are inaccessible.

1 8

234

5 776

■

Rear Panel

XLR inputs

These balanced XLR-3-31 type connectors are used to

connect input signals. They are wired pin 1–ground, pin

2–hot (+), and pin 3–cold (–).

In Bridge mode, only the XLR input of the channel A is

active.

MODE switch

•

STEREO mode

Channels A and B will operate independently.

•

PARALLEL mode

In PARALLEL mode, the channel A input signal will

be sent to the channel A power amp and to the

channel B power amp. The channel B input jack is not

used.

•

BRIDGE mode

In BRIDGE mode, channels A and B will operate

simultaneously, functioning as a single mono amp.

These switches are used to turn on and off the HPF

(High Pass Filter) for each channel. When set to ON,

frequencies below 20 Hz are ﬁltered using a 12 dB/

octave high pass ﬁlter.

SPEAKERS jacks

• These are Speakon type output jacks. Speakon type

cable plugs can be connected here.

• These are ﬁve-way binding post output jacks.

DATA PORT jack

An amp control device, such as the ACD1 or ACU16-C,

can be connected to the DATA PORT jack for

monitoring or controlling the ampliﬁer from the

external device.

AMP ID switch

When an amp control device, such as the ACD1 or

ACU16-C, is connected to the DATA PORT jack

the AMP ID switch can be used to set the ampliﬁer’s ID.

Euroblock connector

This is a balanced input jack. The included Euroblock

connector can be used to make connections here.

AC inlet

Connect the socket of the included AC cable to this

inlet. Connect the plug of the AC cable to an AC outlet

that meets the power supply conditions printed below

this inlet.

GROUND Screw terminal

If you are having a problem with hum or noise, use this

terminal to connect to ground or to connect to the

chassis of the mixer, preamp, or other device in your

system.

56 8 9

Ground

Cold

Hot

HPF 20 switches

■

Speaker connections

Speakers can be connected to the ampliﬁer as shown below. Note that speaker impedance will vary according to the

connection method and the number of speakers. Please be sure that your speaker’s impedance is not less than the relevant

minimum value indicated below.

Connection conﬁgurations for STEREO and PARALLEL modes

When using 5-way binding post output jacks When using the Speakon connector

Connection conﬁgurations for BRIDGE mode

When using 5-way binding post output jacks When using the Speakon connector

When connecting high-impedance speakers in parallel (PC3301N only)

The number of speakers that can be connected varies depending on the rated input of the speakers. The PC3301N can be

connected to speakers with a total rated input of up to 625 W. For example, if you connect ﬁve speakers with a rated input of

5 W (25 W), thirty speakers with a rated input of 10 W (300 W) and twenty speakers with a rated input of 15 W (300 W), the

ampliﬁer can be used with a total rated speaker input of 625 W as shown below:

Be sure to use speakers that support the PC3301N’s line-out voltage of 100 V.

Minimum speaker

impedance: 4 Ω

Minimum speaker

impedance: 4 Ω

Minimum speaker

impedance: 4 Ω

Minimum speaker

impedance: 4 Ω

Minimum speaker

impedance: 8 Ω

Minimum speaker

impedance: 8 Ω

CAUTION

Total rated input of speakers: 625 W (maximum)

5W 10W 15W

51301

5 W x 5 speakers (25 W) 10 W x 30 speakers (300 W)

120

5W 10W 15W

15 W x 20 speakers (300 W)

Connection

■

Using a Euroblock connector

1. If the wire insertion ports are closed, turn the screws on top

of the connector counterclockwise to open the ports.

2. Insert the wires into the appropriate ports, following the

indication of the pole on the input terminal, turn the screws

on top of the connector clockwise to ﬁx the wires.

3. Attach the Euroblock connector to the input terminal on the

unit.

■

Speaker Connection

5-way binding post

1. Turn off the POWER switch.

2. Remove the cover attachment screws and remove the

protective cover from the speaker terminals.

3. Remove about 15 mm of insulation from the end of each

speaker cable, and pass the bare wire through the holes

in the appropriate speaker terminals. Tighten the

terminals to securely clamp the wires. Refer to page 8

for speaker polarities.

Be sure that the bare wire ends do not jut out from the

terminals and touch the chassis. The following shows

how the cable should look when correctly attached.

Note to users in the USA:

Please use Class 3 wiring. (PC9501N, PC6501N, PC4801N)

Please use Class 2 wiring. (PC3301N, PC2001N)

4. Reattach the protective cover over the speaker

terminals.

Speakon connector

1. Turn off the POWER switch.

2. Insert the Neutrik NL4FC plugs into the Speakon connector on the rear of the ampliﬁer, and turn clockwise to lock.

Neutrik NL4FC plugs

If cables will be frequently connected and disconnected, as in the

case of a portable installation, we recommend that you use ferrules

with insulation sleeves. Use a ferrule whose conductor portion has

an external diameter of 1.6 mm or less, and a length of

approximately 7 mm (such as the AI0,5-6WH made by the

Phoenix Contact corporation).

Use a screwdriver

to ﬁx the wires.

Screw

15mm*

* Actual size

Speaker

cable

Bare wire

Chassis

CHANNEL

STEREO or PARALLEL BRIDGE

CHANNEL

Neutrik Ampliﬁer Neutrik Ampliﬁer

1+ A+ 1+ +

1– A– 1–

2+ B+ 2+ –

2– B– 2–

Neutrik Ampliﬁer

1+ B+

1– B–

Air Flow

This unit uses a forced cooling system in which air comes in through the front opening and goes out the rear.

Rack Mounting

If multiple high-power amp units are mounted in a rack with poor ventilation, the heat from the amps will cause the interior

of the amp to become very hot, causing the performance of the amps to be impaired. In particular, when mounting in a rack

whose back can not be left open, mount according to the following instructions.

Rack:

Leave a gap of 10 cm or more between the rear panel of the rack and the rear panel of the ampliﬁer.

Fan:

Use a fan with 1.5 m

/min or more maximum wind and 5 mmH

O or more maximum static pressure.

Mounting:

Install the fan kit on the top slot or the top panel of the rack and install a blanking panel between two amps.

If the unit is rack mounted and transported frequently, we recommend that the rear of the unit be supported by ﬁtting a pair

of metal brackets, one each side.

Example of mounting

The top ﬁgure shows an example of a fan kit (panels and two fans) on the top slot of the rack. The fans are Minebea 3115PS-

12T-B30 (with 0.9 m

/min maximum wind and 5 mmH

O maximum static pressure).

The bottom ﬁgure is a dimensional diagram of a panel on which two 3115PS-12T-B30 are installed.

Air intake

Front

Air exhaust

Side View Rear View

PC9501N/PC6501N/

PC4801N/PC3301N/

PC2001N

PC9501N/PC6501N/

PC4801N/PC3301N/

PC2001N

4-6.5 x 11

463

480

248

4-C15

4-ø4.5

76.2

71.5±0.1

Fan kit

Unit: mm

Specifications

■ General Speciﬁcations

0 dB=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power)

Speciﬁcations and descriptions in this owner’s manual are for information purposes only.

Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any time

without prior notice. Since speciﬁcations, equipment or options may not be the same in

every locale, please check with your Yamaha dealer.

European models

Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.

Inrush Current: 16A (PC9501N), 23A (PC6501N, PC4801N, PC3301N, PC2001N)

Conforms to Environments: E1, E2, E3 and E4

PC9501N PC6501N PC4801N PC3301N PC2001N

Output Power

MIN

120V/240V 230V 120V/240V 230V 120V/240V 230V 120V/240V 230V 120V/240V 230V

1 kHz, THD+N= 1% 8 Ω/STEREO

1000 W x 2 1050 W x 2 700 W x 2 750 W x 2 550 W x 2 500 W x 2 350 W x 2 400 W x 2 230 W x 2 250 W x 2

4 Ω/STEREO

1600 W x 2 1650 W x 2 1100 W x 2 1150 W x 2 850 W x 2 800 W x 2 600 W x 2 700 W x 2 400 W x 2 450 W x 2

8 Ω/BRIDGE

3200 W 3300 W 2200 W 2300 W 1700 W 1600 W 1200 W 1400 W 800 W 900 W

20 Hz–20 kHz 8 Ω/STEREO

MIN

925 W x 2 950 W x 2 650 W x 2 650 W x 2 475 W x 2 450 W x 2 330 W x 2 350 W x 2 200 W x 2 230 W x 2

THD+N= 0.1% 4 Ω/STEREO

1400 W x 2 1500 W x 2 930 W x 2 930 W x 2 725 W x 2 700 W x 2 525 W x 2 550 W x 2 325 W x 2 400 W x 2

8 Ω/BRIDGE

2800 W 3000 W 1860 W 1860 W 1450 W 1400 W 1050 W 1100 W 650 W 800 W

16 Ω/BRIDGE(100V)

––––––625 W 625 W – –

1 kHz 2 Ω/STEREO

MIN

2300 W x 2 2300 W x 2 1500 W x 2 1600 W x 2 1200 W x 2 1200 W x 2 800 W x 2 900 W x 2 500 W x 2 600 W x 2

20ms nonclip 4 Ω/BRIDGE

4600 W 4600 W 3000 W 3200 W 2400 W 2400 W 1600 W 1800 W 1000 W 1200 W

Power Bandwidth

MIN 10 Hz–40 kHz (THD+N= 0.5%)

Half Power

Total Harmonic Distortion (THD + N)

MAX 0.1%

20 Hz–20 kHz, Half Power

Frequency Response MAX 0 dB

RL= 8 Ω, Po= 1 W TYP 0 dB

f=20 Hz–50 kHz MIN –1 dB

Intermodulation Distortion (IMD)

MAX 0.1%

60 Hz:7 kHz, 4:1, Half Power

Channel Separation

MIN 70 dB

Half Power, RL= 8 Ω, 1 kHz, Vol. max.,

input 600 Ω shunt

Residual Noise

MAX –70 dB

Vol. min., 20 Hz–20 kHz (DIN AUDIO)

SN Ratio

MIN 106 dB 105 dB 103 dB 101 dB 100 dB

20 Hz–20 kHz (DIN AUDIO)

Damping Factor

MIN 800 500

RL=8 Ω, f= 1 kHz

Input Sensitivity

TYP +9.2dBu +9.5dBu +7.7dBu +8.0dBu +6.7dBu +6.2dBu +4.7dBu +5.3dBu +2.9dBu +3.2dBu

RL=8Ω (20Hz–20kHz, THD+N = 0.1%)

Voltage Gain (RL=8Ω) TYP 32 dB

Maximum Input Voltage MIN 22 dB

Input Impedance TYP 20 kΩ/Balanced, 10 kΩ/Unbalanced

Controls Front Panel POWER switch (ON/OFF)

Two 31-step Volume knobs (one per ch)

Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL)

HPF switch (ON/OFF) fc=20 Hz 12 dB/octave

DIP switch (6P)

Connectors Input XLR–3–31 type/ch

Euroblock connector/ch

Output SPEAKON/ch, 5-way binding posts

Network RJ45 x 2

Power AC inlet

Indicators POWER/STANDBY Green/Orange

PROTECTION Red

TEMP Red (heatsink temp. 85 ˚C)

REMOTE Green

Level Meters 10 points LED meter/ch

Load protection POWER switch ON muting, DC detection

Amp. Protection Temp. detection (heatsink temp. 90 ˚C), VI limiter (RL 1Ω)

Limiter Comp. : THD 0.5%

Cooling Dual Variable-speed fan

Power Consumption Idling 55 W 40 W

Output power, 4 Ω

750 W/

1000 W

1100 W

700 W/

800 W

450 W/

600 W

450 W/

500 W

500 W 350 W

Power Requirements

120 V, 220 V–240 V; 50 Hz/60 Hz

Dimensions (W x H x D) 480 x 88 x 456 mm (18-7/8" x 3-7/16" x 17-15/16")

Weight 13.0 kg (28.6 lbs) 12.5 kg (27.6 lbs)

Included accessories Power cord, Security cover, Owner’s Manual, 3-pin Euroblock connector x 2

■ Block Diagram

■ Dimensions

480

456

380 26

25 30 370 30 25

Unit: mm

Troubleshooting

The following table lists the main causes of abnormal operation and the corrective measures required as well as the

protective circuit operation in each case.

Current Draw

PC9501N

PC6501N

PC4801N

Indicator Possible Cause Remedy Protection Circuit

CLIP indicator lights up

There is a short at the

ampliﬁer’s speaker outputs, the

speaker’s inputs, or in the

wiring.

Locate and remove the short.

The PC limiter circuit activates

to protect the power transistors.

The impedance of the connected

speaker is too low.

Use a speaker with a minimum

impedance of 4Ω (8Ω in Bridge

mode).

PROTECTION indicator lights

The heat sink temperature has

exceeded 90°C.

Check the ventilation around the

ampliﬁer and improve the

airﬂow if necessary.

The thermal protection circuit

activates to protect the power

transistors.

A DC voltage of ±2 V or greater

was detected in the ampliﬁer’s

output circuit.

Consult your dealer or a Yamaha

service center.

The output relay activates to

protect the speaker system.

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

standby 0.08 0.04505174

idle 1.0 0.5 55 0 55 188 47

1/8 power

8 Ω/ch 8.2 4.5 500 250 250 853 215

4 Ω/ch 10.5 5.8 682 375 307 1050 264

1/3 power

8 Ω/ch 16.8 9.2 1093 667 426 1450 367

4 Ω/ch 23.7 13.0 1613 1000 613 2090 527

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

standby 0.08 0.04505174

idle 1.0 0.5 40 0 40 137 34

1/8 power

8 Ω/ch 5.4 2.9 375 188 188 640 161

4 Ω/ch 6.9 3.8 500 275 225 768 194

1/3 power

8 Ω/ch 11.4 6.3 820 500 320 1090 275

4 Ω/ch 16.4 9.0 1183 733 449 1530 387

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

standby 0.08 0.04505174

idle 1.0 0.5 40 0 40 137 34

1/8 power

8 Ω/ch 3.6 2.0 253 125 128 435 110

4 Ω/ch 6.2 3.4 444 200 244 834 210

1/3 power

8 Ω/ch 8.5 4.7 612 333 279 952 240

4 Ω/ch 15.0 8.2 1077 533 544 1860 468

PC3301N

PC2001N

1/8 power is typical of program material with occasional clipping. Refer to these ﬁgures for most applications.

1/3 power represents program material with extremely heavy clipping.

Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz

1W = 0.860kcal/h, 1BTU = 0.252kcal

Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W].

Inrush current

PC9501N: 7A (100V), 8A (120V), 16A (240V)

PC6501N, PC4801N, PC3301N, PC2001N: 10A (100V), 12A (120V), 23A (240V)

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

standby 0.08 0.04505174

idle 1.0 0.5 40 0 40 137 34

1/8 power

8 Ω/ch 2.7 1.5 189 88 102 348 88

4 Ω/ch 5.0 2.7 357 150 207 707 178

1/3 power

8 Ω/ch 6.4 3.5 459 233 226 771 194

4 Ω/ch 12.0 6.6 866 400 466 1590 401

Line Current (A) Power (W) Thermal Dissipation

100/120V 230/240V In Out Dissipated Btu/h kcal/h

standby 0.08 0.04505174

idle 1.0 0.5 40 0 40 137 34

1/8 power

8 Ω/ch 1.9 1.1 134 58 77 261 66

4 Ω/ch 3.1 1.7 224 88 137 467 118

1/3 power

8 Ω/ch 4.5 2.5 325 153 172 586 148

4 Ω/ch 7.6 4.2 544 233 311 1060 267

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

This mark indicates a dangerous electrically live terminal.

When connecting an external wire to this terminal, it is necessary

either to have “a person who have received appropriate

guidance on handling” make the connection or to use leads or a

cord that have been manufactured in such a way that the

connection can be made simply and without problem.

C.S.G., Pro Audio Division

305APTO-D0

Printed in Japan

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

WD61630

Yamaha PC2001N Omistajan opas

Brändi: Yamaha

Malli: PC2001N

Kategoria: Audio amplifiers

Tyyppi: Omistajan opas

Lataa PDF

raportti

muilla kielillä

polski: Yamaha PC2001N Instrukcja obsługi
Türkçe: Yamaha PC2001N El kitabı
English: Yamaha PC2001N Owner's manual
čeština: Yamaha PC2001N Návod k obsluze
svenska: Yamaha PC2001N Bruksanvisning
русский: Yamaha PC2001N Инструкция по применению
italiano: Yamaha PC2001N Manuale del proprietario
Deutsch: Yamaha PC2001N Bedienungsanleitung
português: Yamaha PC2001N Manual do proprietário
dansk: Yamaha PC2001N Brugervejledning
français: Yamaha PC2001N Le manuel du propriétaire
español: Yamaha PC2001N El manual del propietario
Nederlands: Yamaha PC2001N de handleiding
română: Yamaha PC2001N Manualul proprietarului

Yamaha PC2001N Omistajan opas

Yamaha PC2001N Omistajan opas

muilla kielillä

Liittyvät paperit