ABB 4NWP106819R0001 Quick Manual

—

QUICK GUIDE

PowerValue 11 RT G2

1-3 kVA

—

PowerValue 11 RT G2

1-3 kVA

2 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

—

Document information

PLEASE FULLY READ THIS QUICK GUIDE BEFORE READING THE USER MANUAL AND

OPERATING ON THE UNIT.

Document name : 4NWP106819R0001_ABB_QIG_PVA11 1-3kVA-RT_G2_ML_REV-A

Model : PowerValue 11 RT G2 1-3 kVA

Date of issue : 20.05.2020

Issued by (department) : Product Marketing

Checked by (department) : R&D

Article number : 4NWP106819R0001

Document number : 4NWD005390

Revision : REV-A

Revision date : 20.05.2020

DOCUMENT INFORMATION 3

2 1

—

01

—

02

4 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

—

04

1 2

—

03

DOCUMENT INFORMATION 5

—

05

—

06

—

07

6 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

—

10

—

09

AC output 10A AC input 10A Dry contact output port SNMP/AS400 slot

EBM connector EPO/Dry contact

input port

USB Port RS232

At least 10.5mm

L N G

—

11

—

08

—

09

DOCUMENT INFORMATION 7

—

14

—

15

—

16

AC output 10A AC input 16A RS232 SNMP/AS400 slot

EBM connector EPO/Dry contact

input port

USB

Port

Dry contact output port

AC output 10A AC input 16A RS232 SNMP/AS400 slot

EBM connector EPO/Dry

contact input port

USB

Port

Dry contact output port

AC output 16A

RS232AC output 10A AC input 16A

EBM connector

EPO/Dry

contact input port

USB Port Dry contact output port

AC output 16A

SNMP/AS400

slot

Downstream EBM connector

(output)

Upstream EBM connector

(input)

—

13

8 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

CONTENTS 9

—

QUICK GUIDE

PowerValue 11 RT G2

1-3 kVA

DEUTSCH

PORTUGUÊS

Р У́ С С К И Й

FRANÇAIS

SUOMI

POLSKI

DANSK

ΕΛΛΗΝΙΚΆ

ITALIANO

SVENSKA

中文

ČEŠTINA

DUTCH

ENGLISH

ESPAÑOL

Quick guide 9

Kurzanleitung 23

Guide de référence rapide 39

Guida rapida 55

Guía rápida 71

Guia de Consulta Rápida 87

Pikaopas 103

Kort handledning 119

Kvikguide 133

Rychlý průvodce 147

Краткое руководство 161

Skrócony podręcznik 177

速成指南 193

Σύντομος οδηγός 207

Beknopte installatiehandleiding 223

10 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

—

QUICK GUIDE

PowerValue 11 RT G2

1-3 kVA

Important safety instructions 10

Installation 15

Operation 17

Troubleshooting 19

ENGLISH

12 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

—

Important safety instructions

READ THIS IMPORTANT SAFETY INSTRUCTION CHAPTER BEFORE

READING THE OPERATING MANUAL

Always follow the precautions and

instructions described in this

manual. Any deviations from the

instructions may result in electrical

shock or cause accidental load loss.

ABB DOES NOT TAKE ANY

RESPONSIBILITY FOR DAMAGES

CAUSED THROUGH INCORRECT

MANIPULATIONS OF THE UPS

SYSTEM.

The following symbols are used in this manual, the list below explains

each symbol.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “DANGER”

INDICATES AN IMMINENT ELECTRICAL HAZARD. FAILURE TO OBSERVE THE

RELATED SAFETY NOTE MAY CAUSE INJURY, DEATH OR EQUIPMENT

DAMAGE.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “WARNING”

INDICATES A POTENTIALLY DANGEROUS SITUATION. FAILURE TO OBSERVE MAY

CAUSE INJURY, DEATH OR EQUIPMENT DAMAGE.

THIS SYMBOL IN CONJUNCTION WITH THE SIGNAL WORD “NOTE”

INDICATES OPERATOR TIPS OR PARTICULARLY USEFUL OR IMPORTANT

INFORMATION FOR THE USE OF THE PRODUCT. THIS SYMBOL AND

WORDING DOES NOT INDICATE A DANGEROUS SITUATION.

THIS SYMBOL INDICATES THAT READING THE INSTRUCTION MANUAL/

BOOKLET BEFORE STARTING WORK OR BEFORE OPERATING EQUIPMENT OR

MACHINERY IS COMPULSORY.

—

Operator precautions

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS 13

BATTERIES

DANGER

COMPONENTS INSIDE THE UPS ARE CONNECTED TO THE BATTERY EVEN

WHEN THE UPS IS DISCONNECTED FROM THE MAINS POWER SUPPLY.

DANGER

DISCONNECT THE BATTERIES BEFORE CARRYING OUT ANY KIND OF SERVICE

AND/OR MAINTENANCE. VERIFY THAT NO CURRENT IS PRESENT AND NO

HAZARDOUS VOLTAGE EXISTS IN THE CAPACITOR OR BUS CAPACITOR

TERMINALS.

DANGER

A BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK AND HIGH SHORT

CIRCUIT CURRENT. THE FOLLOWING PRECAUTIONS MUST BE OBSERVED

WHEN WORKING ON BATTERIES:

• REMOVE WATCHES, RINGS OR OTHER METAL OBJECTS

• MAKE USE OF PROPER PPE (PERSONAL PROTECTION EQUIPMENT) AS PER

LOCAL POLICIES AND RULES

- WEAR FLAME/ARC RESISTANT WHOLE BODY CLOTHING

- WEAR SUITABLE VOLTAGE RATED GLOVES

- USE SAFETY DIELECTRIC FOOTWEAR

- WEAR ARC FLASH FACE SHIELD

- USE VOLTAGE RATED TOOLS

• DO NOT LAY TOOLS OR METAL PARTS ON TOP OF BATTERIES

• DISCONNECT THE CHARGING SOURCE PRIOR TO CONNECTING OR

DISCONNECTING BATTERY TERMINALS.

DANGER

THE BATTERY CIRCUIT IS NOT ISOLATED FROM THE INPUT VOLTAGE.

HAZARDOUS VOLTAGES MAY OCCUR BETWEEN THE BATTERY TERMINALS

AND THE GROUND. VERIFY THAT NO VOLTAGE IS PRESENT BEFORE

SERVICING.

WARNING

NEVER DISPOSE BATTERIES ON FIRE AS THEY MAY EXPLODE.

DANGER

SERVICING OF BATTERIES INVOLVES ENERGY AND SHOCK HAZARD AND

SHOULD BE PERFORMED BY PERSONNEL KNOWLEDGEABLE ABOUT

BATTERIES AND REQUIRED PRECAUTIONS

WARNING

DO NOT OPEN OR DAMAGE THE BATTERIES.

ENGLISH

14 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

WARNING

RELEASED ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES.

WARNING

REPLACE BATTERIES WITH THE SAME NUMBER AND SAME TYPE OF

BATTERIES.

INSTALLATION

DANGER

DISPLAY A WARNING LABEL ON ALL PRIMARY POWER ISOLATORS INSTALLED

REMOTE FROM THE UPS AREA TO WARN ELECTRICAL MAINTENANCE

PERSONNELS THAT THE CIRCUIT FEEDS A UPS.

MAKE SURE THAT WARNING LABEL CONTAINS THE FOLLOWING TEXT OR

EQUIVALENT: “ISOLATE THE UPS (UNINTERRUPTIBLE POWER SUPPLY)

BEFORE WORKING ON THIS CIRCUIT”.

DANGER

HIGH FAULT CURRENTS (LEAKAGE CURRENTS). BEFORE CONNECTING THE

MAINS ENSURE THAT THE UPS IS GROUNDED!

DANGER

TO PREVENT RISK OF SHOCKS AND RISK OF FAILURE DO NOT CUT, REWORK

OR MANIPULATE THE MATERIAL DELIVERED WITH THE UPS

DO NOT REMOVE ANY SCREWS FROM THE UPS SYSTEM OR FROM THE

BATTERY CABINET: DANGER OF ELECTRICAL SHOCK.

DANGER

WHEN OPENING OR REMOVING THE UPS COVERS YOU ARE EXPOSED TO

DANGEROUS VOLTAGES.

TO PREVENT RISK OF ELECTRIC SHOCK, ONLY QUALIFIED PERSONNEL MAY

REMOVE THE UPS COVER

DANGER

CIRCUITS BEHIND DISPLAY LCD CAN CREATE RISK OF ELECTRIC SHOCK IF

EXPOSED. DO NOT TRY TO ROTATE THE DISPLAY BY USING HANDS OR TOOL.

PLEASE REFER TO CHAPTER 4.6 OF THE USER MANUAL TO ROTATE THE

DISPLAY.

WARNING

THE WIRING INSTALLATION SHALL BE PERFORMED BY QUALIFIED

PERSONNEL ONLY.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS 15

DANGER

RISK OF BACKFEED VOLTAGE, ISOLATE THE UPS INSTALLING AN EXTERNAL

ISOLATING DEVICE BETWEEN MAINS INPUT AND UPS; BEFORE OPERATING

ON THIS CIRCUIT, CHECK FOR HAZARDOUS VOLTAGE.

DANGER

TO REDUCE THE RISK OF FIRE, THE UNIT SHOULD ONLY CONNECT TO A

CIRCUIT PROVIDED WITH BRANCH CIRCUIT OVERCURRENT PROTECTION FOR:

• D CURVE 10A RATING (UPSTREAM CIRCUIT), FOR 1kVA (B/S) MODELS,

• D CURVE 16A RATING (UPSTREAM CIRCUIT), FOR 2kVA (B/S) MODELS,

• D CURVE 20A RATING (UPSTREAM CIRCUIT), FOR 3kVA (B/S) MODELS.

DANGER

HIGH LEAKAGE CURRENT:

MAKE SURE THAT THE EARTH WIRE IS CONNECTED.

COMMON INPUT/OUTPUT SOURCES CONNECTION

WARNING

BEFORE CARRING OUT ANY CONNECTION, CHECK THAT THE UPSTREAM

PROTECTION DEVICES (NORMAL AC SOURCE AND BYPASS AC SOURCES) ARE

OPEN “0” (OFF).

WARNING

WATER CONDENSING MAY OCCUR IF THE UPS IS UNPACKED IN A VERY LOW

TEMPERATURE. IN THIS CASE IT IS NECESSARY TO WAIT UNTIL THE UPS IS

FULLY DRIED INSIDE OUT BEFORE PROCEEDING INSTALLATION AND USE TO

AVOID HAZARDS AND ELECTRIC SHOCK, WAIT UNTIL THE UPS IS FULLY DRY

BOTH INSIDE AND OUTSIDE BEFORE INSTALLING.

WARNING

INDUCTIVE LOADS (FOR EXAMPLE MONITORS AND LASER PRINTERS) HAVE A

VERY HIGH POWER CONSUMPTION AT START-UP. IF CONNECTED TO THE

UPS, THE START-UP POWER OF SUCH LOADS MUST BE TAKEN INTO

CONSIDERATION WHEN CALCULATING THE CAPACITY OF THE UPS TO

PREVENT THE UPS FROM BEING OVERLOADED AND TURNED OFF.

NOTE

TO REDUCE THE RISK OF FIRE, CONNECT THE UPS TO A CIRCUIT PROVIDED

WITH BRANCH CIRCUIT OVERCURRENT PROTECTION WITH AN AMPERE

RATING IN ACCORDANCE WITH THE IEC/EN 60934 STANDARD OR YOUR

LOCAL ELECTRICAL CODE.

SEE TECHNICAL SPECIFICATIONS FOR RECOMMENDATIONS.

ENGLISH

16 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

OPERATION

WARNING

DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE.

WARNING

DO NOT DISCONNECT THE MAINS CABLE FROM THE UPS OR THE BUILDING

WIRING SOCKET DURING OPERATION AS THIS REMOVES THE GROUND FROM

THE UPS AND ALL CONNECTED LOADS.

WARNING

SWITCH OFF THE CONNECTED LOADS BEFORE TURNING ON THE UPS. THEN

SWITCH ON THE LOADS ONE BY ONE AFTER THE UPS IS TURNED ON. SWITCH

OFF ALL OF THE CONNECTED LOADS BEFORE TURNING OFF THE UPS.

WARNING

REPLACE FUSES ONLY BY DEVICES OF THE SAME TYPE AND OF THE SAME

AMPERAGE TO AVOID FIRE HAZARDS.

NOTE

PRESS THE OFF BUTTON TO FULLY DISCONNECT THE UPS. WAIT UNTIL THE

UPS IS ON BYPASS OR ON STAND-BY MODE BEFORE DISCONNECTING IT

FROM THE MAINS.

NOTE

INDISCRIMINATE OPERATION OF SWITCHES MAY CAUSE OUTPUT LOSS OR

DAMAGE TO EQUIPMENT.

ENGLISH

INSTALLATION 17

—

Installation

Planning before the installation

To ensure a long service life, install

the unit in a position where any

danger to the UPS is minimized:

• Install the UPS indoors.

• Leave enough space on each side

of the cabinet to allow cooling

airflow and ensure that the

circulation of air to the ventilation

slits is not obstructed.

• Avoid excessively high

temperatures and excessive

moisture.

• Make sure that the surface is solid

and flat

Preparation

For safety consideration, the UPS is

shipped out from factory with

battery wires disconnected. Before

install the UPS, please follow the

steps below:

1. Remove front panel. (figure 01)

2. Connect the battery wires.

(figure 02)

3. Put the front panel back to the

unit. (figure 03)

Rack mount installation – requires

rack mounting kit, to be purchased

separately

UPS:

This procedure is suitable for 19-

inch rack cabinet installation with a

minimum depth of 800 mm. Identify

the final position and keep 2U

spacing for this installation.

4. Install the ear bracket onto the

unit using the M4 flathead

screws (figure 04).

5. Slide the unit into the rail kit and

make sure to tighten the rack-

mounting screw (figure 05).

6. After installing the UPS into the

rack, proceed with the

connection of the load to the

UPS. Make sure the load devices

are turned off before plugging

them into the output receptacles.

External battery modules:

Identify the final position and keep

2U spacing for this installation; it is

recommended that this spacing is

provided below the UPS.

1. Install the ear bracket onto the

unit with the flathead M4

screw. (figure 04).

2. Slide the unit into the rail kit

and make sure to tighten the

rack-mounting screw

(figure 05).

3. Connect the EBM to the UPS

with the battery power cable

(figure 16).

4. Install fixing plate to fix battery

cable.

Tower installation

UPS:

1. Set up the stabilizer bracket

then put the unit into the

stabilizer bracket. (figure 06).

Note: Please install the 4 screws to

ENGLISH

18 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

ensure that the unit is correctly

placed in standalone/tower position

External battery modules:

1. Set up the extension plate as

below and install it on the UPS

stabilizer bracket. (figure 07)

2. Install the UPS and EBM

individually into the stabilizer

bracket.

3. Connect to the UPS with the

battery power cable (refer to rack

position installation).

Note: It is recommended that this

unit be installed to UPS’s right hand

side. If installing an additional unit,

place it next to the previous unit.

PowerValue 11 RT G2 3kVA S

installation

1. The cover and cable gland must

be installed over input

terminals and input cables to

prevent risk of electric shock

during standalone/tower use.

2. Push in the hole of terminal

cover.

3. Separate pressure dome and

lock nut, assemble the provided

spare cable glands on the two

sides of terminal cover and

screw it tightly. (figure 08)

4. Pass the input cable through

the gland assembly; use PVC

single cord, 3G, 2.5 mm2,

double-insulated, rated 300 V

(IEC 60227-1). The overall

diameter of the power supply

cord must be approximately

10.5 mm to allow reliable

clamping from cable gland, to

prevent failure from arcing and

electric shock. (figure 09)

5. Connect three wires according

to the polarities indicated on

the terminal blocks. Be sure to

connect ground first.

6. Put the terminal cover back on

the UPS by fixing 4 screws.

(figure 10)

7. The UPS does not incorporate a

disconnect device, that must

be part of the building

installation: UPS mains input

shall be protected by an 2-pole

overcurrent protection device

according to IEC 60898-1 / IEC

60947-2 not exceeding 25 A.

(figure 11)

Electrical connections

The figures 12, 13, 14, 15 and 16 at

the beginning of the manual, show

the connectors and ports in the UPS

and external battery module rear

panel.

ENGLISH

OPERATION 19

—

Operation

You can operate the UPS through

the user-friendly display

(see chapter 4 of the user manual

for a full list of possible operations).

UPS start-up

To start up the UPS with mains

supply:

1. Check that all cables are securely

and correctly connected.

2. Keep the power button pressed

for longer than 1 second. The

fans will activate and the UPS will

load for a few seconds.

3. The UPS will perform a self-test

and the LCD will show the default

UPS status screen

Note: Bypass mode is enabled by

default and can be configured

through the user’s settings (for

more information, see table 6 of the

user manual).

To start up the UPS without mains

supply (cold start):

4. Check that all cables are securely

and correctly connected.

5. Keep the power button pressed

for longer than 1 second. The UPS

will power on, the fans will

activate and the LCD will turn on.

The UPS will perform a self-test

and show the default UPS status

screen.

25 %

50 %

7

5

%

100%

BATT

BA

TT

LO W

L

OA

D

2

5

%

5

0

%

75

%

100%

LO AD

E

CO

VAC

%

H

z

VDC

H

M

VAC

%

H

z

VDC

H

M

Selection

keys

LCD

ENGLISH

20 POWERVALUE 11 RT G2 1-3 KVA QUICK GUIDE

6. Keep the power button pressed

for longer than 1 second. The

alarm buzzer will sound for 1

second and the UPS will start up.

7. After a few seconds, the UPS

transfers to battery mode. When

the UPS is supplied with power

from the mains, the UPS

transfers to online mode without

interrupting the UPS power

output.

UPS Shutdown

To shut down the UPS with mains

supply:

1. If the UPS is working in bypass

mode, go to step 3.

2. If the UPS is in online mode, keep

the power button pressed for

more than 3 seconds. The alarm

buzzer will sound and the UPS

will transfer to bypass mode.

Danger: The output is still

energized.

3. Disconnect the mains power

supply. The display will shut

down and the output voltage will

be removed from the UPS output

terminal.

4. If the bypass has been disabled

via the Settings menu, keep the

power button pressed for longer

than 3 seconds to shut down the

UPS. The unit will transfer from

online to standby mode.

Disconnect the input power

cable and the display will shut

down.

To shut down the UPS without

mains supply:

1. To power off the UPS, keep the

power on/off button pressed for

more than 3 seconds. The alarm

buzzer will sound for 3 seconds

and the output power will be

immediately cut off.

2. The display will shut down and

the output voltage will be

removed from the UPS

output terminal.

ENGLISH

Sivu latautuu...

ABB 4NWP106819R0001 Quick Manual

Tämä ohje sopii myös

ABB 4NWP106819R0001 Quick Manual

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat