Black & Decker CLM3825L2 Ohjekirja

Kategoria
Lawnmowers
Tyyppi
Ohjekirja
CLM3825
www.blackanddecker.eu
2
A B
C D
E F
3
G H
I J
K L
4
M N
O P
Q R
5
S T
U
V
W
Your BLACK+DECKER CLM3825 mower has been designed for
mowing grass. This appliance is intended for consumer use only.
When using cordless appli-
ances, basic
safety precautions, including
the following, should always be followed
personal injury and material damage.
When using the machine the
safety rules must be followed. For your
own safety and bystanders please read
these instructions before operating the
machine. Please keep the instruc-tions
safe for later use.
Read all of this manual carefully before
operating the appliance.
The intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
Retain this manual for future refer-
ence.
Always take care when using the appli-
ance.
This appliance is not intended for use
supervision.
The appliance is not to be used as a
toy.
Do not allow children or animals to
come near the work area or touch the
appliance or power supply cord.
Close supervision is necessary when
the appliance is used near children.
Use in a dry location only. Do not allow
the appliance to become wet.
Do not immerse the appliance in water.
Do not open body casing. There are
no userserviceable parts inside.
Do not operate the appliance in
explosive atmospheres, such as in the
or dust.
To reduce the risk of damage to plugs
and cords never pull the cable to
remove the plug from a socket.
When not in use, the appliance should
be stored in a dry, well ventilated place
out of the reach of children.
Children should not have access to
stored appliances.
When the appliance is stored or trans-
ported in a vehicle it should be placed
in the boot or restrained to prevent
movement following sudden changes
in speed or direction.
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts, damage to switches
and any other conditions that may af-
fect its operation.
Do not use the appliance if any part is
damaged or defective.
Have any damaged or defective parts
repaired or replaced by an authorised
repair agent.
ENGLISH
(Original instructions)
Never attempt to remove or replace
this manual.
Be careful during adjustment of the
mower to prevent entrapment of the
When servicing the blades be aware
that, even though the power source
is switched off, the blades can still be
moved.
Firmly grip handle with both hands
when operating the lawnmower.
If at any time it is felt necessary to tilt
the lawnmower, make sure that both
hands remain in the operating position
while the lawnmower is tilted. Keep
both hands in the operating position
until the lawnmower is returned to rest
correctly on the ground.
Never wear radio or music head-
phones while operating the lawnmow-
er.
Never attempt to make a wheel height
adjustment while the motor is running
or while the safety key is in the switch
housing.
If the lawnmower stalls, release bail
bar to turn mower off, wait for blade to
stop and remove the safety key, before
attempting to unclog the chute or
remove anything from under the deck.
Keep hands and feet away from cut-
ting area.
Keep blades sharp. Always use protec-
tive gloves when handling the lawn-
mower blade.
If you are using the grass collector,
check it frequently for wear and dete-
rioration. If excessively worn, replace
with a new grass collector for your
safety.
Use extreme caution when reversing
or pulling the lawnmower towards you.
Do not put hands or feet near or under
the lawnmower. Keep clear of the
discharger opening at all times.
Clear the area where the lawnmower
is to be used of objects such as rocks,
sticks, wire, toys, bones etc., which
could be thrown by the blade. Objects
struck by the blade can cause severe
injury to persons. Stay behind the
handle when the motor is running.
Do not operate the lawnmower bare-
footed or while wearing sandals.
Always wear substantial footwear.
Do not pull lawnmower backward un-
less absolutely necessary. Always look
down and behind before and while
moving backward.
Never direct discharged material
toward anyone. Avoid discharging
material against a wall or obstruction.
Material may ricochet back toward the
operator. Release the bail bar to turn
the lawnmower off and stop the blade
when crossing gravel surfaces.
ENGLISH
(Original instructions)
Do not operate the lawnmower without
the entire grass collector, discharge
guard, rear guard, or other safety
protective devices in place and work-
ing. Periodically check all guards and
safety protective devices to ensure
they are in good working order and
will operate properly and perform their
intended function. Replace a damaged
guard or other safety device before
further use.
Never leave a running lawnmower
unattended. Always remove the safety
key if the lawnmower is going to be left
unattended.
Always release the bail bar to stop
the motor and wait until the blade
comes to a complete stop and remove
the safety key before cleaning the
lawnmower, removing the grass bag,
unclogging the discharge guard, when
leaving the lawnmower, or before
making any adjustments, repairs or
inspections.
Operate lawnmower only in daylight
the path of the blade are clearly visible
from the operating area of the lawn-
mower.
Do not operate the lawnmower while
or when your are tired or ill. Always
stay alert, watch what you are doing,
and use common sense.
Avoid dangerous environments. Never
operate the lawnmower in damp or wet
grass, never use lawnmower in the
rain. Always be sure of your footing,
walk, never run.
If the lawnmower should start to
vibrate abnormally, release the bail
bar, wait for the blade to stop and
remove the safety key, then check for
the cause immediately. Vibration is
generally a warning of trouble, see the
troubleshooting guide for advise in the
case of abnormal vibration.
Always wear proper eye and respira-
tory protection when operating the
lawnmower.
The use of any accessory or attach-
ment not recommended for use with
this lawnmower could be hazardous.
Only use accessories approved by
BLACK+DECKER.
Never overreach while operating the
lawnmower. Always be sure to keep
proper footing and balance at all times
while operating the lawnmower.
Mow across the face of slopes,
never up and down. Exercise extreme
caution when changing direction on
slopes.
Watch for holes, ruts, bumps, rocks or
other hidden objects. Uneven terrain
could cause a slip and fall accident.
Tall grass can hide obstacles.
Do not mow on wet grass or exces-
sively steep slopes. Poor footing could
cause a slip and fall accident.
ENGLISH
(Original instructions)
Do not mow near drop-offs, ditches,
or embankments. You could lose your
footing or balance.
Always allow the mower to cool down
before storing.
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children must be supervised to ensure
that they do not play with the appli-
ance.
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotat-
ing/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your tool
(example:- working with wood, espe-
cially oak, beech and MDF.)
The following warning symbols are found
on the appliance along with the date code:
Read the manual
prior to operation.
R
Do not expose the appliance to
rain or high humidity.
Always remove the safety key
before cleaning the lawnmower,
removing the grass bag, unc-
logging the discharge guard,
when leaving the lawnmower, or
before making any adjustments,
repairs or inspections.
bystanders away from the cut-
ting area.
F
Wear eye protection
The blades will
continue to rotate
after the machine is
switched off.
ENGLISH
(Original instructions)
Directive 2000/14/EC guaran-
teed sound power.
Never attempt to open for any reason.
Do not expose the battery to water.
Do not expose the battery to heat.
Do not store in locations where the
temperature may exceed 40 °C.
Charge only at ambient temperatures
between 10 °C and 40 °C.
Charge only using the charger pro-
vided with the appliance/tool. Using
the wrong charger could result in an
electric shock or overheating of the
battery.
When disposing of batteries, follow
the instructions given in the section
"Protecting the environment".
Do not damage/deform the battery
pack either by puncture or impact, as
Do not charge damaged batteries.
Under extreme conditions, battery
leakage may occur. When you notice
liquid on the batteries carefully wipe
the liquid off using a cloth. Avoid skin
contact.
In case of skin or eye contact, follow
the instructions below.
personal injury or damage to property. In
case of skin contact, immediately rinse
with water. If redness, pain or irritation
occurs seek medical attention. In case of
eye contact, rinse immediately with clean
water and seek medical attention.
p
Do not attempt to charge dam-
aged batteries.
Your charger has been designed for a
Always check that the mains voltage
corresponds to the voltage on the rating
plate.
Never attempt to replace
the charger unit with a regular mains
plug.
Use your BLACK+DECKER charger only
to charge the battery in the appliance/
tool with which it was supplied. Other
batteries could burst, causing personal
injury and damage.
Never attempt to charge non-recharge-
able batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/tool/battery must be
placed in a well ventilated area when
charging.
ENGLISH
(Original instructions)
$
The charger is intended for
indoor use only.
Read the instruction manual
before use.
#
Your charger is double insu-
lated; therefore no earth wire is
required. Always check that the
mains voltage corresponds to the
voltage on the rating plate. Never
attempt to replace the charger
unit with a regular mains plug.
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
This appliance includes some or all of the following features.
1. Safety key
2. Bail bar
3. Lock off release
4. Handle bar
5. Cable restraint clips
6. Upper handle
7. Upper handle quick release clamp
8. Grass box full indicator
9. Grass collection box
10. Lower Handle
11. Lower handle quick release clamp
12. Spring loaded rear door
13. Height adjust handle
14. Battery cover
15. Battery cover release
16. Handle
Before assembly, make sure that the tool is
switched off and the safety key and battery have been
removed.
The grass box requires assembly before use and comes in 3
pieces.
Clip the 2 sides of the grass collection box (9) together
Align the lid (17) onto the assembled grass collection box.
Ensure that the guides and clips are aligned.
Take extra care when aligning the clips at the rear of the
grass collection box.
Push down on the lid to secure all clips. Begin at the
front and work towards the back. Ensure that all clips are
securely located.
Remove the lower handle quick release clamps (11) from
the base of the mower.
Place the lower handle (10) around the base, making
sure the three notches (18) on the lower handle (10) face
toward the top.
Screw the lower handle quick release clamps (11) through
the lower handle into the mower base, With the lower
handle quick release clamps screwed in half way, close
the handle and base interlock. If the connection between
the handle and quick release clamps is too tight or loose,
adjust the depth of the quick release clamps and close
them again until the teeth are fully closed.
Fit the upper handle (6) to the lower handle (10) using the
upper handle quick release clamps (7) and clamp nuts
(19) as shown.
Screw the upper handle quick release clamps (7) through
the lower handle into the clamp nuts (20), With the
upper handle quick release clamps screwed in half way,
between the handle and quick release clamps is too tight
or loose, adjust the depth of the quick release clamps and
close them again until the teeth are fully closed.
Release the lower handle quick release clamp as shown.
Lift or lower the handle into one of the 3 marked positions
next to the lower handle quick release clamps.
Close the lower handle quick release clamps (11) and
ensure the teeth of the handle and base interlock. If the
connection between the handle and quick release clamps
is too tight or loose, adjust the depth of the quick release
clamps and close them again until the teeth are fully
closed.
Secure the cable to the upper and lower handle by cliping
it into the cable restraint clips (5)
ENGLISH
(Original instructions)
box (9) over the lugs (20).
Your mower features the BLACK+DECKER Easy - height adjust-
ment system. This system will adjust all four wheels at the
same time.
The mower has six blade height adjustment positions (30 mm
to 80 mm). Refer to the scale on the side of the mower. The
pointer will indicate the height setting for cutting your lawn.
This setting can be a reference for the next time you want to
cut your lawn to the same height.
Release the bail bar (2) to turn the lawnmower off, wait
until the blade stops and remove the safety key (1).
To raise or lower the cutting height, place the palm of your
hand on the palm rest (21) and pull the height adjustment
lever (13) away from the mower body.
Move the height adjust lever (13) into the required position
then push it back in towards the mower body.
Make sure that the mower is securely locked in one of
the six positions.
Place the mower on level ground.
Release the bail bar (2) to turn the mower off, wait for the
blade to stop and remove the safety key (1).
Pull the battery cover release (15) towards the front of the
mower body and lift the battery cover (14).
Lift the battery (22) out of the mower.
Pull the battery cover release (15) towards the front of the
mower body and lift the battery cover (14).
Slide the battery (22) into the mower. (the battery will only
Let the appliance work at its own pace. Do not
overload.
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
To charge the battery (22), insert it into the charger (23).
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
(slowly).
The charge is complete when the charging indicator (24)
lights green continuously. The charger and the battery can be
occasionally tops off the battery charge. The charging indica-
tor (24) will be lit as long as the battery is connected to the
plugged-in charger.
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
The charger and battery pack can be left connected with the
pack fresh and fully charged.
If the charger detects a weak or damaged battery, the charg-
follows:
Re-insert the battery (22).
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original bat-
tery is defective and should be returned to a service centre
for recycling.
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
be used to display the current level of charge in the battery
during use and during charging.
Press the state of charge indicator button (25).
Remove the safety key:
Whenever leaving the appliance unattended.
Before cleaning a blockage.
Before checking, cleaning or working on the appliance.
After striking a foreign object.
Whenever the appliance starts vibrating abnormally.
Sharp moving blade. Never attempt to override the
operation of this switch and safety key system as a serious
injury could result.
Insert the safety key (1) fully into the switch housing.
Push the lock off release button (3) on the top of the
switch housing.
Pull the blade bail bar (2) toward the handle bar (4).
ENGLISH
(Original instructions)
To turn the lawnmower off, release the blade bail bar (2).
When the bail bar (2) has returned to the original position it
will activate the automatic braking mechanism. The motor is
electrically braked and the lawnmower blade will stop rotating
in 3 seconds or less.
The lawn mower has a device which allows you to easily see
when the grass box is full and needs emptying.
When the lawn mower is running and the grass box is
empty the indicator will be in the open position (26).
When the lawn mower is running and the grass box is full
the indicator will be in the closed position position (27).
grass is about 63 mm to 76 mm high. Mowing too early in
the season restricts the root systems of the grass which
renew themselves every spring. New grass should be
mowed when it is about 63 mm high.
Do not remove too much grass blade surface at one time,
never more than 1/3 of the leaf height during each cutting.
Cutting too close ‘shocks' sensitive grass blades, resulting
lawn to reach water in the soil.
Mow your lawn when it is dry to avoid clumping of wet
grass. If you have a choice, late afternoon is the ideal time
for mowing, not only because the grass is dry, but also
because the sensitive new cut area of the grass will not be
exposed to intense sunlight.
Keep the mowing blade sharp for a nice clean cut. This
improves the mower's performance and enhances the look
of your lawn. A dull blade shatters and bruises the tips of
the grass. This impairs the healthy growth of your lawn
and increases the susceptibility to turf diseases. If the
grass tips are bruised it causes a brownish colour which
gives your lawn an unhealthy appearance. A dull blade
may also pull up young grass seedlings.
Try to mow your lawn at a consistent cutting height. While
there are times when you should vary the cutting height
with the changing seasons, a consistent cutting height
produces a healthier, lovelier lawn with generally fewer
weeds. Mow more frequently during periods of fast growth.
Frequent cutting ensures that the lower, less attractive
portion of the grass will not show.
If your lawn has grown too long, during a vacation for ex-
ample, mow at a cutting height one or two positions higher
than normal. A second pass at your usual cutting height
a few days later will put your lawn back on schedule.
Changing the cutting height is a simple matter with
BLACK+DECKER One Touch Wheel Height Adjustment,
which simultaneously adjusts all four wheels at once.
During the spring and autumn, or after an interruption to
the cutting schedule, the grass will be longer and thicker. If
the motor continually slows down while cutting, try setting
the wheels for a higher cutting height. Excessive motor
loading can result in uneven cutting, quicker discharge of
the battery and can cause the motor to overload which
stops the motor.
There are three good ways to enhance your lawn's
appearance: Vary the mowing direction frequently; mow
horizontally on hillsides; (this is also a good safety prac-
tice) and do not forget to overlap the mowing path on each
pass.
Always inspect the area where the lawnmower is to be
used and remove all stones, sticks, wire, bones and other
debris which could be thrown by the rotating blade.
Mow across the face of slopes, never up-and-down. Exer-
cise extreme caution when changing direction on slopes.
Do not mow excessively steep slopes. Always maintain a
good footing.
Release the bail bar (2) to turn the lawnmower off when
crossing any gravel area as stones can be thrown by the
rotating blade.
Set the lawnmower at the highest cutting height when
mowing in rough ground or in tall weeds. Removing too
much grass at one time may cause the motor to overload
which will stop the lawnmower. Refer to the troubleshoot-
ing guide.
If the grass box (9) is used during the fast growing season, the
grass may tend to clog up at the discharge opening.
Release the bail bar (2) to turn the lawnmower off and
remove the safety key (1).
Remove the grass box (9) and shake the grass to the
back of the bag.
Clean out any grass or debris which may be packed
around the discharge opening.
If the lawnmower starts to vibrate abnormally:
Release the bail bar (2) immediately to turn the lawn-
mower off and remove the safety key (1) and the battery
pack (22).
Investigate the cause of the vibration. Vibration is a warn-
ing. Do not operate the lawnmower until a service check
has been made. Refer to the troubleshooting guide in the
manual.
Always release the bail bar to turn the lawnmower off
and remove the safety key when leaving it unattended even
for a short period of time.
The following suggestions will help you to obtain optimum
run-time from your cordless mower:
Slow down in areas where the grass is especially long or
thick.
Avoid mowing when the grass is wet.
Cut your lawn frequently, especially during periods of high
growth.
Your BLACK+DECKER corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool/appliance care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
ENGLISH
(Original instructions)
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Do not touch the blade before the safety key has
been removed and the blades have come to a complete stop.
Release the bail bar (2) to turn mower off, wait for the
blade to stop and remove the safety key (1).
Cut a piece of wood (approximately 50 mm x 100 mm x
600 mm long) to use to keep the blade from turning while
Turn the mower on its side.
Wear gloves and proper eye protection. Be careful
of the sharp edges of the blade.
Remove the washer (30), blade (31), square blade guide
and fan (33) for damage and replace if necessary.
blade (Indicated by arrows on either end) will face the ground
when the mower is returned to its normal upright position.
Install the fan (33). Be sure to position the fan blades (34)
so that they face in towards the mower.
Install the blade guide (32). Be sure to position the 'D'
shaped pegs (35) so that they face out, away from the
mower.
Fit the blade (31) onto the blade guide (32) with the ar-
rows facing outwards.
Position the piece of wood (28) to keep the blade (31)
with a 13mm wrench.
Keep the blade sharp for best performance. A dull blade does
not cut grass cleanly or mulch properly.
Always make sure that the safety key is removed.
Wear proper eye protection while removing, sharp-
ening and installing a blade.
Sharpening the blade twice during a mowing season is usually
blade to dull quickly. If your lawn has sandy soil more frequent
sharpening may be required.
Replace bent or damaged blades immediately.
Make sure that the blade remains balanced.
Sharpen the blade at the original cutting angle.
Sharpen the cutting edges on both ends of the blade,
removing equal amounts of material from both ends.
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1) and the battery pack (22) and
turn the lawnmower on to its side.
Remove the blade (31) from the mower, see the instruc-
tions for removing and installing blades.
Wear proper eye protection and gloves and be
careful of the sharp edges of the blade.
Put the blade (31) in a vice.
cutting edge.
Check the balance of the blade, see the instructions for
blade balancing.
Install the blade (31) on the mower and tighten securely,
see the instructions for removing and installing blades.
Check the balance of the blade by putting the centre hole
in the blade on to a nail or a round shank screwdriver that
is clamped horizontally in a vice. If either end of the blade
is balanced.
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1).
Use only mild soap and a damp cloth to clean the mower.
Use a blunt tool to clean out any clippings which may have
accumulated on the underside of the mower.
After several uses, check all exposed fasteners for tight-
ness.
Fertilisers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilisers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
Remove the safety key (1).
Wipe all exposed parts with a damp cloth.
ENGLISH
(Original instructions)
The rotating blade can cause serious injury.
Release bail bar to turn mower off and remove the safety key
before lifting, transporting or storing the mower. Store in a dry
place.
The mower will not be as heavy to lift if the battery pack
mower.
In warm climates, to ensure optimal performance it is recom-
mended that the battery is maintained on constant charge.
The battery may be stored with the charger disconnected if
the following conditions are met.
The battery is fully charged before storing.
The average temperature of the storage location is below
10°C (50°F).
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Before proceeding, release the bail bar to turn
mower off, wait for the blade to stop and remove the safety
key.
Check to make sure the safety key has been
installed and is fully seated and that the lock off
button is being completely depressed before
moving the bail handle.
Release the bail handle to turn mower off. Remove
the safety key and battery pack, turn the mower
over and check that the blade is free to turn.
Check that the battery cavity is free of debris and
that the battery is installed properly.
Has the battery been fully charged? Press the state
of charge button. Charge the battery if required.
Release the bail handle to turn mower off. Remove
the safety key and battery pack, turn the mower
over and check that the blade is free to turn.
Raise the cutting height of the wheels to the
highest position and start the mower.
Check that the battery cavity is free of debris and
that the battery is installed properly.
Has the battery been fully charged? Press the state
of charge button. Charge the battery if required.
Avoid overloading the mower. Slow down the
cutting pace, or raise the cut height.
Has the battery been fully charged? Press the state
of charge button. Charge the battery if required.
Release the bail handle to turn the mower off.
Remove the safety key and battery pack. Turn the
mower over and check:
Blade for sharpness - Keep the blade sharp.
Deck and discharge chute for clogging.
Wheel height adjustment may be set too low for the
grass condition. Raise the cutting height.
Raise the cutting height to reduce deck drag on the
grass. Check each wheel for free rotation.
Release the bail handle to turn the mower off.
Remove the safety key and battery pack. Turn the
mower on its side and check the blade to ensure it
has not been bent or damaged. If the blade is
damaged, replace with a BLACK+DECKER
replacement blade. If the underside of the deck is
damaged, return mower to a BLACK+DECKER
Authorized service center
If there is no visible damage to the blade and the
mower still vibrates: Release the bail handle to turn
mower off, remove the safety key and battery pack
and then remove the blade. Rotate the blade
vibrates, return the mower to an authorized
BLACK+DECKER service center.
Chute clogged. Release the bail handle to turn
mower off. Remove the safety key and battery
pack. Clear the chute of grass clippings.
Too much cut grass being cut. Raise the cutting
height of wheels to shorten the length of the cut.
Bag full. Empty bag more often.
Z
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
able for separate collection.
z
Separate collection of used products and packag-
ing allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
ENGLISH
(Original instructions)
BLACK+DECKER provides a facility for the collection and
recycling of BLACK+DECKER products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised repair
the address indicated in this manual. Alternatively, a list of
authorised BLACK+DECKER repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Z
At the end of their useful life, discard batteries with
due care for our environment:
Run the battery down completely, then remove it from the
tool.
NiCd, NiMH and Li-Ion batteries are recyclable. Place
the battery(s) in a suitable packaging to ensure that the
terminals cannot be short-circuited. Take them to any
authorised repair agent or a local recycling station.
Do not short-circuit the battery terminals.
in a risk of personal injury or an Explosion.
H 1
V
DC
36
min
-1
3500
kg
16.2
V
DC
36
Ah
2.5
Li-Ion
V
AC
230
V
DC
36
mA 1300
h 1.5-2.0
Hand/arm weighted vibration value:
= < 2.5 m/s
2
, uncertainty (K) = 1.5 m/s
2
.
L
PA
(sound preasure) 80 dB(A)
uncertainty (K) = 3 dB(A)
This mower can cut up to 300m
2
on a single 2Ah battery
pack.
This area (300m
2
) is achieved on a single, fully charged,
2Ah battery pack in dry conditions with the height adjust-
ment lever in position 6 following light growth conditions.
In damp conditions, lower height settings or heavy growth
conditions the area of cut may be less than 300m
2
.
2006/42/EC, EN 60335-1:2012 +A11:2014,
EN 60335-2-77:2010
2000/14/EC, Lawn Mower, L < 50cm, Annex VI,
TÜV SÜD Product Service GmbH, Ridlstraße 65,
80339 München, Germany
Level of accoustic power according to 2000/14/EC (Article 12,
Annex III, L ≤ 50 cm):
L
WA
(measured sound power) 92 dB(A)
uncertainty (K) = 3 dB(A)
L
WA
(guaranteed sound power) 96 dB(A)
ENGLISH
(Original instructions)
%
CLM3825 Lawnmower
Black & Decker declares that these products described under
"technical data" are in compliance with:
These products also comply with Directive 2004/108/EC (until
19/04/2016) 2014/30/EU (from 20/04/2016) and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
R. Laverick
Engineering Manager
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
28/09/2015
BL2536-XJ
BDC2A36-QW
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to
faulty materials, workmanship or lack of conformity, within
24 months from the date of purchase, Black & Decker guar-
antees to replace defective parts, repair products subjected
to fair wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
The product has been used for trade, professional or hire
purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through foreign
objects, substances or accidents;
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register
your new BLACK+DECKER product and to be kept up to date
on new products and special offers. Further information on the
BLACK+DECKER brand and our range of products is available
at www.blackanddecker.co.uk
ENGLISH
(Original instructions)
18
Bestimmungsgemäße Verwendung
Ihr BLACK+DECKER CLM3825 Rasenmäher wurde zum
Rasenmähen entwickelt. Dieses Gerät ist nicht für den
gewerblichen Einsatz vorgesehen.
Sicherheitshinweise
Achtung!
Beachten Sie beim Um-
gang mit kabellosen Geräten stets die
grundlegenden Sicherheitshinweise,
die im Folgenden beschrieben werden.
Dadurch verhindern Sie Brände, Strom-
schläge sowie Sach- und Personen-
schäden.
Achtung!
Beachten Sie beim Ver-
wenden des Geräts unbedingt die Sicher-
heitsregeln. Lesen Sie zu Ihrer eigenen
Sicherheit und zum Schutz in der Nähe
des Geräts die folgende Bedienungsan-
leitung. Heben Sie diese Anleitung zur
späteren Verwendung gut auf.
Lesen Sie diese Anleitung vollständig
und aufmerksam durch, bevor Sie das
Gerät verwenden.
Der vorgesehene Verwendungszweck
ist in dieser Anleitung beschrieben.
Bei Verwendung von Zubehör oder
Anbauteilen, die nicht in dieser An-
leitung empfohlen werden, sowie bei
der Verwendung des Geräts in Ab-
weichung von den in dieser Anleitung
beschriebenen Verfahren besteht
Verletzungsgefahr.
Bewahren Sie diese Anleitung auf.
Verwendung des Geräts
Verwenden Sie das Gerät stets mit
Umsicht.
Das Gerät ist nicht für die unbeaufsich-
tigte Verwendung durch Kinder oder
gebrechliche Personen vorgesehen.
Das Gerät ist kein Spielzeug.
Achten Sie darauf, dass sich im
Arbeitsbereich keine Kinder oder
Tiere aufhalten. Verhindern Sie, dass
Kinder das Gerät oder das Netzkabel
berühren.
Seien Sie besonders vorsichtig, wenn
Sie das Gerät in der Nähe von Kindern
verwenden.
Verwenden Sie das Gerät nur in trock-
ener Umgebung. Achten Sie darauf,
dass das Gerät nicht nass wird.
Tauchen Sie das Gerät nicht in Wass-
er.
Versuchen Sie nicht, das Gehäuse zu
zu wartenden Teile.
Betreiben Sie das Gerät nicht in ex-
plosionsgefährdeter Umgebung, in der
sich brennbare Flüssigkeiten, Gase
Ziehen Sie niemals am Kabel, wenn
Sie den Stecker aus der Steckdose
ziehen möchten. Kabel und Stecker
könnten sonst beschädigt werden.
Nach dem Gebrauch
Bewahren Sie das Gerät bei Nich-
tgebrauch an einem trockenen, gut
belüfteten Ort außerhalb der Reich-
weite von Kindern auf.
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
19
Kinder sollten keinen Zugang zu auf-
bewahrten Geräten haben.
Wenn das Gerät in einem Fahrzeug
transportiert oder gelagert wird,
bewahren Sie es im Kofferraum oder
einer geeigneten Ablage auf, damit es
bei plötzlichen Geschwindigkeits- oder
Richtungsänderungen nicht in Bewe-
gung geraten kann.
Inspektion und Reparaturen
Prüfen Sie das Gerät vor der Verwend-
ung auf beschädigte oder defekte
Teile. Prüfen Sie, ob Teile gebrochen
sind, Schalter beschädigt wurden oder
andere Bedingungen vorliegen, die die
Funktion beeinträchtigen können.
Betreiben Sie das Gerät nicht, wenn
ein Teil beschädigt oder defekt ist.
Lassen Sie beschädigte oder defekte
Teile in einer Vertragswerkstatt repari-
eren oder austauschen.
Ersetzen oder entfernen Sie keine
Teile, für die in dieser Anleitung keine
entsprechende Beschreibung en-
thalten ist.
Gehen Sie bei Einstellungen am
Rasenmäher vorsichtig vor, um zu
verhindern, dass Ihre Finger zwischen
den beweglichen Messern/Teilen
und feststehenden Teilen des Geräts
eingeklemmt werden.
Beachten Sie bei Wartungsarbeiten
an den Messern, dass sich diese auch
ohne Stromversorgung bewegen.
Zusätzliche Sicherheitshin-
weise für Rasenmäher
Halten Sie den Rasenmäher während
des Betriebs sicher mit beiden Händen
fest.
Halten Sie beide Hände in der Be-
triebsposition, wenn der Rasenmäher
gekippt werden muss. Halten Sie
beide Hände in der Betriebsposition
bis der Rasenmäher wieder ordnungs-
gemäß auf dem Boden abgestellt
wurde.
Tragen Sie beim Rasenmähen keine
Kopfhörer zum Musikhören.
Passen Sie niemals die Höhe der
Räder an, während der Motor läuft
oder sich der Sicherheitsschlüssel im
Lassen Sie den Bügelschalter los,
und entfernen Sie den Sicherheitss-
chlüssel, um den Rasenmäher aus-
zuschalten, wenn dieser blockiert.
Warten Sie, bis das Messer zum
Stillstand gekommen ist, bevor Sie
versuchen, die Verstopfung zu be-
seitigen oder Gegenstände von der
Unterseite zu entfernen.
Halten Sie Hände und Füße vom
Schnittbereich fern.
Halten Sie die Sägeblätter scharf. Tra-
gen Sie beim Umgang mit dem Messer
des Rasenmähers stets Schutzhands-
chuhe.
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
20
Wenn der Grasfangbehälter verwen-
det wird, muss dieser regelmäßig auf
Abnutzungen und Beschädigungen
überprüft werden. Wechseln Sie aus
Sicherheitsgründen den Grasfangbe-
hälter bei starker Abnutzung aus.
Seien Sie besonders vorsichtig, wenn
Sie den Rasenmäher wenden oder in
Ihre Richtung ziehen.
Bringen Sie Hände oder Füße nicht in
die Nähe bzw. unter den Rasenmäher.
Halten Sie jederzeit einen Sicher-
heitsabstand zur Auswurföffnung.
Entfernen Sie Steine, Äste, Drähte,
Spielzeuge, Knochen usw., die in das
Messer geraten könnten, aus dem
Bereich, in dem der Rasenmäher
verwendet wird. Objekte, die in das
Messer geraten, können ernsthafte
Verletzungen verursachen. Bleiben Sie
hinter dem Griff, wenn der Motor läuft.
Betreiben Sie den Rasenmäher weder
barfuß noch mit Sandalen. Tragen Sie
jederzeit festes Schuhwerk.
Ziehen Sie den nur Rasenmäher nur
rückwärts, wenn dies unbedingt er-
forderlich ist. Achten Sie stets auf den
Boden und den Bereich hinter Ihnen,
bevor und während Sie sich rückwärts
bewegen.
Achten Sie darauf, dass das Material
nicht in Richtung von Personen ausge-
worfen wird. Achten Sie darauf, dass
das Material nicht in Richtung von
Wänden oder anderen Gegenständen
ausgeworfen wird. Das Material kann
gegen den Bediener zurückgeschleud-
ert werden. Lassen Sie den Bügels-
chalter los, und warten Sie, bis das
Messer zum Stillstand gekommen ist,
-
en.
Betreiben Sie den Rasenmäher nicht
ohne angebrachten und intakten Gras-
fangbehälter, Auswurfschutz, hinteren
Schutz und andere Schutzvorrichtun-
gen. Überprüfen Sie regelmäßig alle
Schutz- und Sicherheitsvorrichtungen
auf deren ordnungsgemäße Funktion.
Ersetzen Sie beschädigte Schutz- und
Sicherheitsvorrichtungen vor der wei-
teren Verwendung.
Lassen Sie den eingeschalteten
Rasenmäher niemals unbeaufsichtigt.
Entfernen Sie stets den Sicherheitss-
chlüssel, wenn Sie den Rasenmäher
unbeaufsichtigt lassen.
Lassen Sie stets den Bügelschalter
los, warten Sie, bis das Messer zum
Stillstand gekommen ist, und entfernen
Sie den Sicherheitsschlüssel, wenn
Sie den Rasenmäher reinigen, den
Grasfangbeutel entfernen, Verstopfun-
gen aus der Auswurföffnung beseiti-
gen, den Rasenmäher unbeaufsichtigt
lassen bzw. Anpassungen vornehmen
oder Reparaturen und Inspektionen
ausführen.
(Übersetzung der ursprünglichen Anweisungen)
DEUTSCH
1 / 1

Black & Decker CLM3825L2 Ohjekirja

Kategoria
Lawnmowers
Tyyppi
Ohjekirja