Yamaha SPX2000 Ohjekirja

EN

Owner’s Manual

Keep This Manual For Future Reference.

(5)-1

2

SPX2000—Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the included power cord.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Do not place the power cord near heat sources such as heaters or radiators, and do

not excessively bend or otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over, or roll anything over it.

• Do not open the device or attempt to disassemble the internal parts or modify

them in any way. The device contains no user-serviceable parts. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place containers on it containing liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of

sound during use of the device, or if any unusual smells or smoke should appear to be

caused by it, immediately turn off the power switch, disconnect the electric plug from

the outlet, and have the device inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall over.

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the device, TV, or radio may

generate noise.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to minimum.

• Be sure to connect to a properly grounded power source. A ground screw

terminal is provided on the rear panel for safely grounding the device and

preventing electrical shock.

• Do not insert your ﬁngers or hand in any gaps or openings on the device.

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device. If this happens, turn off the power immediately

and unplug the power cord from the AC outlet. Then have the device inspected

by qualiﬁed Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• This device has a built-in backup battery. When you unplug the power cord from

the AC outlet, the internal data is retained. However, if the backup battery fully

discharges, this data will be lost. When the backup battery is running low, the

LCD indicates “Low Battery!”. In this case, immediately save the data to a

computer or other external device, then have qualiﬁed Yamaha service

personnel replace the backup battery.

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

Handling caution

Backup battery

(5)-1

SPX2000—Owner’s Manual

3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur of

gelieve dan contact op te nemen met de vertegenwoordiging van

Yamaha in uw land.

•For the removal of the battery at the moment of the disposal at the

end of life please consult your retailer or Yamaha representative

ofﬁce in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : PROFESSIONAL MULTI-EFFECT PROCESSOR

Model Name : SPX2000

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interfer-

ence that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

(5)-1

4

SPX2000—Owner’s Manual

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated “danger-

ous voltage” within the product’s enclosure that

may be of sufﬁcient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral trian-

gle is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not

ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recep-

tacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories speciﬁed by

the manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speci-

ﬁed by the manufacturer, or

sold with the apparatus. When a

cart is used, use caution when

moving the cart/apparatus com-

bination to avoid injury from tip-

over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the appara-

tus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

* This applies only to products distributed

by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

CAUTIONS:

• This unit is a CLASS I device. Connect the unit to a mains socket

outlet that features a protective ground terminal.

• This unit is not completely disconnected from the mains when you

turn off the POWER switch, which is a single pole switch.

SPX2000—Owner’s Manual

5

• All illustrations in this owner’s manual are for explanatory purposes; they may differ

from the actual specifications.

• Company names and product names appearing in this manual are the trademarks or

registered trademarks of their respective owners.

Table of contents

Features of the SPX2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Parts and their functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Editing an effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Other functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Early Reflection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Delay, Echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Pitch Change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Composite effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Freeze. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Other effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Preparations for using MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

What you can do using MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

MIDI data format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

MIDI Control Change Parameter Assignment Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Error message list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

6

SPX2000—Owner’s Manual

Features of the SPX2000

●

High-quality sound

High quality is guaranteed by 96 kHz 24-bit digital processing.

●

Flexible support for a variety of situations and applications

122 different effects are provided as presets, meeting the needs of a wide variety of situations and applica-

tions. You can edit these preset effects to create your own unique sounds.

●

Control effects remotely

You can use the SPX2000 Editor

(*)

or MIDI messages to control effects remotely. You can not only switch

effects, but also modify the effect parameters to make ﬁne adjustments, or make the effect vary in conjunc-

tion with your performance on a MIDI keyboard.

*Refer to “Controlling the SPX2000 from your computer,” below.

●

Manage effect data on your computer

You can use the SPX2000 Editor to manage or back up your original effects and data. For example you could

create a separate library for each live performance or recording project, and store effects for just that event.

Then you can simply swap the data (USER bank) for each occasion, allowing you to use effects efﬁciently.

★

Digital input/output

By connecting an AES/EBU format compatible device

you can input/output audio in digital form.

★

Intuitive operation

Operation is intuitive; use the [STORE] button to store

an effect, the [RECALL] button to recall an effect, and

the [

▲

INC]/[

▼

DEC] buttons to increment/decre-

ment a parameter value.

★

Instant recognition of effect types

The SPX2000’s display shows a different background

color (by default) for each type of effect. You can tell the

general effect type at a glance; e.g., cyan (light blue) for

reverb and early reﬂection, white for delay, magenta for

modulation, and green for effects of the Classic bank.

★

New reverb algorithms

New reverbs feature the newly-developed REV-X algo-

rithm, delivering rich, high-density reverberation with

smooth decay, spaciousness, and depth that brings out

the best in the original signal.

★

Classic SPX effects revived with new algorithms

Favorite effects such as gate reverb, freeze, and ﬂanger

have been carried over from previous SPX-series mod-

els, with newly developed algorithms.

★

Stereo input/output

The SPX2000 provides full stereo operation; 2 IN/2

OUT.

★

Tempo synchronization

Some effects can be synchronized to a speciﬁed note

length and tempo. The tempo can be set using the front

panel [TAP] button, from a foot switch such as the FC5,

or via MIDI messages.

★

A full range of MIDI functionality

You can use MIDI to switch effects, modify parameter

values, or transmit/receive bulk data.Effects and tempo

synchronization can also be controlled via MIDI.

Hardware features

Controlling the SPX2000 from

your computer

You can use the SPX2000 Editor to remotely control

the SPX2000 from your computer. The SPX2000

Editor is expected to be available for downloading

from the following website. For the latest informa-

tion, please visit the website.

Yamaha Pro Audio Website:

http://www.yamahaproaudio.com/

For details on the SPX2000 Editor, refer to the

operating manual for the software.

Software features

SPX2000—Owner’s Manual

7

Parts and their functions

Front panel

1

[INPUT L R] control

This concentric pair of knobs adjusts the level of the

analog input signal. The inner knob controls the L

channel, and the outer knob controls the R channel.

2

Level meters

These indicate the signal level pre-effect or post-effect

(page 103).

3

[INPUT MODE] button/indicator

This button selects monaural input or stereo input.

The indicator will light to indicate the currently

selected input mode.

4

[METER] button/indicator

This button selects either pre-effect or post-effect as

the signal whose level will be shown in the level meter

(

2

). The indicator will light to indicate the currently

selected signal.

5

[INPUT SOURCE] indicator

This indicates the currently selected input source. Use

“INPUT SOURCE” (page 19) to select the input

source.

6

[CLOCK] indicator

This indicates the currently selected word clock source.

Use “CLOCK SOURCE” (page 18) to select the word

clock source.

7

[MIDI] indicator

This will light when the SPX2000 receives MIDI data.

8

[kHz] indicator

This indicates the currently-operating word clock fre-

quency.

9

Display

This displays information about the currently-recalled

effect or the selected utility function.

0

Effect number indicator

This indicates the effect number of the currently

selected effect. If the selected effect is different than the

recalled effect, the number will blink. When you store

or recall an effect, the blinking number will change to

steadily lit.

A

[BANK] button/indicator

This button selects the effect bank. The indicator for

the selected bank will light. For details on banks, refer

to “Three banks” (page 12).

B

[STORE] button

This button stores the selected effect.

C

[

▲

]/[

▼

] buttons

These buttons select an effect.

D

[RECALL] button

This button recalls the selected effect.

E

[UNDO] button/LED

Use this button when you want to undo the preceding

store/recall/erase operation (page 16). The LED will

light if the [UNDO] button is available.

F

[BACK] button

This button selects the preceding parameter.

G

[

▲

INC]/[

▼

DEC] buttons

Use these buttons to edit parameter values.

2 3 57 9 0 B E I J MFC G

H N O

DA4681 LK

P

8 SPX2000—Owner’s Manual

H [NEXT] button

This button selects the next parameter.

I [COMPARE] button/LED

Use this button to compare the effect before editing

(immediately after recall) and after editing. If you edit

a parameter after recalling an effect, this LED will light.

The LED will go dark when you store or recall an effect

(page 16).

J [PARAMETER] button/LED

This button selects the basic parameters of the effect.

This LED will light if basic parameters are selected.

K [FINE PARAM] button/LED

This button selects the FINE parameters of the effect.

The FINE parameters supplement the basic parame-

ters. This LED will light if FINE parameters are

selected.

L [UTILITY] button/LED

This button selects the SPX2000’s utility functions. For

details, refer to “Other functions” (page 17). This LED

will light if a utility function is selected.

M [BYPASS] button/LED

This button switches the effect on/off. When the

[BYPASS] button is off (LED dark), the effect will be

applied to the input signal and output from the output

jacks. When the [BYPASS] button is on (LED lit), the

input signal will be sent from the output jacks without

modiﬁcation.

N [TAP] button/LED

Use this to set the tempo value of the effect. When you

press this button twice or more, the tempo value will be

calculated from the average interval at which you press

the button. If the effect SYNC parameter is on, the LED

will blink at the interval of the tempo value.

O [FOOT SW] jack

You can connect an optional foot switch (such as the

FC5) to this jack and the foot switch to input the

tempo as an alternative to using the [TAP] button (N)

(page 23).

P [POWER ON/OFF] button

This button turns the power of the SPX2000 on/off.

NOTE: The following buttons will be inoperable when the

[UTILITY] LED (

L

) is lit.

• [BANK] button (

A

)

• [STORE] button (

B

)

• [

▲

]/[

▼

] buttons (

C

)

• [RECALL] button (

D

)

• [UNDO] button (

E

)

• [COMPARE] button (

I

)

NOTE: The [BYPASS] button will turn off when you recall

an effect.

SPX2000—Owner’s Manual 9

Rear panel

Q Grounding screw

For safety, use this screw to ground the SPX2000.

The included power cable has a three-prong plug; if the

electrical outlet you use is correctly grounded, the

SPX2000 will be appropriately grounded. If the electri-

cal outlet is not grounded, use this screw to ground the

SPX2000. Correctly grounding the SPX2000 will effec-

tively reduce hum and interference.

R [AC IN] jack

Connect the power cable to this jack. First connect the

power cable to the SPX2000, and then connect the

other end to the electrical outlet.

S [MIDI OUT/THRU] connector

You can connect a MIDI device to this connector and

use MIDI messages to send SPX2000 data to it. You can

bulk-dump SPX2000 data via MIDI, or re-transmit

MIDI data received at the [MIDI IN] connector (T)

from this connector without change. Use “MIDI OUT

SETUP” (page 21) to specify whether this connector

functions as “MIDI OUT” or “MIDI THRU.”

T [MIDI IN] connector

You can connect a MIDI device to this connector and

use messages transmitted from that device to remotely

control the SPX2000 (page 88).

U [TO HOST USB] connector

You can use a USB cable to connect your computer

here. You can use SPX2000 Editor or your MIDI appli-

cation to remotely control the SPX2000 from your

computer (page 6).

V [WORD CLOCK IN] jack

Connect this jack to a device that supplies a word clock

signal. This jack is terminated with a 75-ohm resistor.

Connect this jack in a one-to-one connection with the

device supplying the word clock.

W [AES/EBU OUT] jack

Connect an AES/EBU format device to this jack. This

XLR-3-32 jack outputs an AES/EBU format digital sig-

nal.

X [AES/EBU IN] jack

Connect an AES/EBU format device to this jack. This

XLR-3-31 jack inputs an AES/EBU format digital sig-

nal.

Y [OUTPUT] jacks

Connect these jacks to the effect return of your mixer

or to the input of your power amp. These jacks output

analog signals. Use either the XLR-3-32 jacks or the

TRS phone jacks, as appropriate for the device you are

connecting.

Z [OUTPUT –10 dBu/+4 dBu] switch

Set this to either –10 dBu or +4 dBu according to the

input level of the device connected to the [OUTPUT]

jacks (Y).

[ [INPUT] jacks

Connect these jacks to the effect send of your mixer or

to the output of an electronic musical instrument.

These jacks input analog signals. Use either the XLR-3-

31 jacks or the TRS phone jacks, as appropriate for the

device you are connecting.

In order to enable these jacks, you must set the input

source setting to “ANALOG” (page 19).

\ [INPUT –10 dBu/+4 dBu] switch

Set this to either –10 dBu or +4 dBu according to the

output level of the device connected to the [INPUT]

jacks ([).

R S T W XYU V

ZQ \

[

Use only the supplied power cord.

10 SPX2000—Owner’s Manual

Operation

Basic operation

This section provides a simple explanation of how to input signals to the SPX2000,

apply effects, and output the result. The overall steps are as follows.

Make connections to external devices

↓

Turn the power on

↓

Select the input signal

↓

Select an effect

↓

Recall the effect

↓

Switch the effect on/off

The connectors you use will depend on whether the input/

output signals are analog or digital.

• Analog input:

Connect your device to the [INPUT] jacks ([).

• Digital input:

Connect your device to the [AES/EBU IN] jack (X).

• Analog output:

Connect your device to the [OUTPUT] jacks (Y).

• Digital output:

Connect your device to the [AES/EBU OUT] jack (W).

Related items

• Selecting the word clock source......................... page 18

•Using your computer to

control the SPX2000 ............................................ page 6

•Using MIDI messages to

control the SPX2000 .........................................page 88

Here’s how to turn on the power of a system that includes

the SPX2000.

1 Protect your monitor system

Before you turn on the power of the SPX2000, turn off

the power of the device that is connected to the [OUT-

PUT] jacks (Y) or [AES/EBU OUT] jack (W). Also

turn the [INPUT L R] control (1) to minimize the

L/R input signal level (the inner knob controls the L

channel, and the outer knob controls the R channel).

2 Turn on the power of the SPX2000

Press the [POWER ON/OFF] button (P) to turn the

power on.

→ The front panel display and LEDs will light.

3 Turn on your external devices

Turn on the power of devices connected to the

SPX2000.

Make connections to external

devices

NOTE: If you are inputting/outputting analog signals, you must

set the [INPUT –10 dBu/+4 dBu] switch (

\

) and the [OUTPUT

–10dBu/+4dBu] switch (

Z

) appropriately for the signal level of

the connected devices.

You must turn off the power of all devices before you

make connections.

Turn the power on

NOTE:To prevent high-volume noise from being out-

put from your speakers, turn on the power starting

with the device that is closest to the audio source.

Example: sound modules → mixer → SPX2000 →

power amp

Reverse this order when turning the power off.

SPX2000—Owner’s Manual 11

Operation

You will need to make several selections regarding the

input signal.

Select monaural or stereo input

Use the [INPUT MODE] button (3) to select either mon-

aural input or stereo input. Each time you press the

[INPUT MODE] button the indicator will alternate

between MONO and STEREO.

The signal ﬂow will change as follows depending on

whether the input is monaural or stereo, and on the num-

ber of inputs/outputs for the effect you recall.

Select the signal for metering

Use the [METER] button (4) to select either the pre-

effect signal or the post-effect signal for display in the level

meter (2). Each time you press the [METER] button the

indicator will alternate between INPUT and OUTPUT.

Check the status of the input signal

The following indicators will light to indicate the state of

the input signal.

• INPUT SOURCE (5):

This will indicate whether the input signal is ANALOG

or DIGITAL. If you want to change input sources, use

“INPUT SOURCE” (page 19) to select the desired input

source.

• MIDI (7):

This indicator will light when MIDI data is received.

• CLOCK (6):

This indicates the word clock source. Use “CLOCK

SOURCE” (page 18) to select the word clock source.

• kHz (8)

This indicates the word clock frequency (44.1/48/88.2/96

kHz). If you are using the SPX2000’s internal clock, you

can use “CLOCK SOURCE” (page 18) to select the fre-

quency.

Use the [INPUT L R] control (1) to adjust the analog

input signal levels (L/R); the inner knob controls the L

channel, and the outer knob controls the R channel.

Select the input signal

FX

IN L

IN R OUT R

OUT L

L

R

C

–3 dB

FX

IN L

IN R OUT R

OUT L

L

R

L

R

FX

IN L

(MONO)

IN L

(MONO)

IN R OUT R

OUT L

L

R

C

FX

IN R OUT R

OUT L

L

R

L

R

Monaural input 1IN 2OUT

Monaural input 2IN 2OUT

Stereo input 1IN 2OUT

Stereo input 2IN 2OUT

INT

The SPX2000’s internal clock

The SPX2000 will operate as the

clock master.

You will need to set other con-

nected devices to be clock slaves.

AES/EBU

Clock data received at the [AES/EBU IN]

jack (X)

The SPX2000 will operate as a clock

slave.

WC

Clock will be received at the [WORD

CLOCK IN] jack (V)

The SPX2000 will operate as a clock

slave.

Adjust the input level

12 SPX2000—Owner’s Manual

Here’s how to select the effect that you want to apply to the

input signal.

1 Select a bank

Press the [BANK] button (A) several times to select

the bank that contains the desired effect.

→ The [BANK] indicator (A) shows the currently

selected bank.

2 Select an effect

Use the [▲]/[▼] buttons (C) to select the effect you

want to use.

→ The number of the currently-selected effect will

blink in the effect number indicator (0).

Press the [RECALL] button (D) to recall the effect.

→ The recalled effect will be applied to the output signal.

You can use the [BYPASS] button (M) to switch the effect

on/off.

→ Each time you press the button the effect will be

switched on/off. When the [BYPASS] button is on, the

effect will be off and the input signal will be output

without modiﬁcation.

Three banks

The SPX2000 has three effect banks; PRESET,

USER, and CLASSIC. These banks are organized as

follows.

PRESET bank

This bank contains a total of 97 effects; 80

effects based on new algorithms and ranging

from standard to distinctive, and 17 newly-

developed reverb (REV-X) effects.

The effects in this bank are read-only.

CLASSIC bank

This bank contains 25 simple and easy-to-use

effects based on early models of the SPX series.

The effects in this bank are read-only.

USER bank

When shipped, this bank does not contain

effects. You can edit effects from the PRESET

bank or CLASSIC bank and store them as your

own original effects in the USER bank. Once

you have stored an effect, you can recall and use

it in the same way as the effects of the PRESET

bank or CLASSIC bank.

You can store 99 effects in this bank.

Select an effect

[▲] button

Press to move to the following effect.

Hold

to continue moving through

the following effects.

Hold down

[▲] and

press [▼]

to move more rapidly through

the following effects.

[▼] button

Press to move to the preceding effect.

Hold

to continue moving through

the preceding effects.

Hold down

[▼] and

press [▲]

to move more rapidly through

the preceding effects.

NOTE: The following buttons will be inoperable when the

[UTILITY] LED (

L

) is lit

• [BANK] button (

A

)

• [STORE] button (

B

)

• [

▲

]/[

▼

] buttons (

C

)

• [RECALL] button (

D

)

• [UNDO] button (

E

)

• [COMPARE] button (

I

)

NOTE: While you are selecting an effect (i.e., while the effect

number indicator is blinking), pressing any of the following

buttons will cancel the effect selection; the currently-recalled

effect will appear in the display.

• [UNDO] button (

E

)

• [BACK] button (

F

)

• [

▲

INC]/[

▼

DEC] buttons (

G

)

• [NEXT] button (

H

)

• [COMPARE] button (

I

)

• [PARAMETER] button (

J

)

• [FINE PARAM] button (

K

)

Recall the effect

NOTE: You can press the [UNDO] button (

E

) to undo the

preceding Recall operation. The [UNDO] LED will light if UNDO

is available.

Switch the effect on/off

SPX2000—Owner’s Manual 13

Operation

Editing an effect

This section explains the process of editing a selected effect and storing it. The over-

all steps are as follows.

Select an effect

↓

Select a parameter

↓

Edit the parameter

↓

Check the edited effect

↓

Store the effect

↓

(Undo the preceding Store operation)

Select the effect that you want to edit.

1 Select a bank

Use the [BANK] button (A) to select the bank con-

taining the effect you want to edit.

→ The [BANK] indicator (A) shows the currently

selected bank.

2 Select an effect (page 12)

Use the [▲]/[▼] buttons (C) to select the effect you

want to edit.

→ The number of the currently selected effect will

blink in the effect number indicator (0).

3 Recall the effect

Press the [RECALL] button (D) to recall the effect.

→ The effect number indicator (0) will change from

blinking to steadily lit.

Select an effect

NOTE: While you are selecting an effect (i.e., while the effect

number indicator is blinking), pressing any of the following

buttons will cancel the effect selection; the currently-recalled

effect will appear in the display.

• [UNDO] button (

E

)

• [BACK] button (

F

)

• [

▲

INC]/[

▼

DEC] buttons (

G

)

• [NEXT] button (

H

)

• [COMPARE] button (

I

)

• [PARAMETER] button (

J

)

• [FINE PARAM] button (

K

)

NOTE: The following buttons will be inoperable when the

[UTILITY] LED (

L

) is lit

• [BANK] button (

A

)

• [STORE] button (

B

)

• [

▲

]/[

▼

] buttons (

C

)

• [RECALL] button (

D

)

• [UNDO] button (

E

)

• [COMPARE] button (

I

)

Basic parameters and Fine

parameters

Each of the SPX2000’s effects consists of two types

of parameter: Basic parameters and Fine parame-

ters.

Since some effects have a rather large number of

parameters, the parameters that you will probably

need to edit most often are grouped as “Basic

parameters,” and supplementary parameters are

grouped as “Fine parameters.”

The number and type of Basic parameters and Fine

parameters will differ for each effect.

Effect

Basic parameter 1

Basic parameter 2

Basic parameter 3

Basic parameter n

Fine parameter 1

Fine parameter 2

Fine parameter 3

Fine parameter m

14 SPX2000—Owner’s Manual

To edit a parameter, you must ﬁrst select it. The editable

parameters will differ for each effect. For details, refer to

the explanation of each parameter in the “Effects” section

(page 25 and following).

1 Select a Basic parameter or Fine parameter

Press either the [PARAMETER] button (J) or the

[FINE PARAM] button (K) to select the type of

parameter that you want to edit.

→ The LED of the button you pressed will light.

2 Select a parameter

Use the [BACK] button (F) or [NEXT] button (H) to

select the parameter that you want to edit.

→ The currently selected parameter is shown in the

display (9).

Selecting Basic parameters

Press the [BACK] button

to move to the preceding parameter.

Press and hold the [BACK] button

to continue moving through the preceding parameters.

Press the [NEXT] button or [PARAMETER] button

to move to the following parameter.

Press and hold the [NEXT] button or [PARAMETER] but-

ton

to continue moving through the following parameters.

Selecting FINE parameters

Press the [BACK] button

to move to the preceding parameter.

Press and hold the [BACK] button

to continue moving through the preceding parameters.

Press the [NEXT] button or [FINE PARAM] button

to move to the following parameter.

Press and hold the [NEXT] button or [FINE PARAM] but-

ton

to continue moving through the following parameters.

Use the [▲ INC]/[▼ DEC] button (G) to edit the value of

the parameter.

→ The parameter value shown in the display (9) will

change, and the [COMPARE] LED (I) will light.

The [COMPARE] LED (I) indicates that the currently-

recalled effect has been edited since it was recalled.

Select a parameter

NOTE: If the display indicates “NO FINE PARAMETER,” an

effect from the CLASSIC bank is recalled.

The effects of the CLASSIC bank do not have Fine parameters.

Use the [PARAMETER] button to select the Basic parameters.

REV-X LARGE HALL

REV TIME= 3.20s

Edit the parameter

[▲ INC]

button

Press

to increment the parameter

value.

Hold

to continue incrementing the

parameter value.

Hold down

[▲ INC] and

press [▼ DEC]

to continue incrementing the

parameter value faster.

[▼ DEC]

button

Press

to decrement the parameter

value.

Hold

to continue decrementing the

parameter value.

Hold down

[▼ DEC] and

press [▲ INC]

to continue decrementing the

parameter value faster.

Setting the tempo

Some effects have a Tempo parameter. You can edit

the Tempo parameter in any of the following ﬁve

ways.

• Use the [▲ INC]/[▼ DEC] button (G)

This is the same method as when editing other

parameters.

• Use the [TAP] button (N)

When you press the [TAP] button (N) two or

more times, the average interval will be calculated

and set as the Tempo value. If you want to use this

method, set “TEMPO SOURCE” (page 23) to

specify “TAP” as the synchronization source.

• Use the foot switch

When you press the foot switch (optional) two or

more times, the average interval will be calcu-

lated and set as the Tempo value. If you want to

use this method, use the following procedure.

1. Connect an optional foot switch (e.g., FC5) to

the [FOOT SW] jack (O).

2. Set the “TEMPO SOURCE” setting (page 23)

to specify “TAP” as the synchronization source.

• Use MIDI clock

The interval of MIDI Clock messages can be used

to set the Tempo value. If you want to use this

method, set “TEMPO SOURCE” (page 23) to

specify “MIDI” as the synchronization source.

• Use MIDI control changes

The value speciﬁed by a MIDI Control Change

message can be used to set the Tempo value. By

using this method you can control the SPX2000’s

Te mpo value from a connected external MIDI

device.

SPX2000—Owner’s Manual 15

Operation

Effects and tempo synchronization

Some of the SPX2000’s effects allow you to synchronize the effect with the tempo. There are two such types of effect; delay-

type effects and modulation-type effects. For delay-type effects, the delay time will change according to the tempo. For mod-

ulation-type effects, the frequency of the modulation signal will change according to the tempo.

• Parameters related to tempo synchronization

The following ﬁve parameters are related to tempo synchronization.

1) SYNC 2) NOTE 3) TEMPO 4) DELAY 5) FREQ.

SYNC: ........................................This is the on/off switch for tempo synchronization.

NOTE and TEMPO: .................These are the basic parameters for tempo synchronization.

DELAY and FREQ.:................... DELAY is the delay time, and FREQ. is the frequency of the modulation signal. These

directly affect the way in which the effect sound will change. DELAY is relevant only

for delay-type effects, and FREQ. is relevant only for modulation-type effects.

• How the parameters are related

Te mpo synchronization uses TEMPO and NOTE to calculate a value that will be the basis for the tempo, and continues

making adjustments so that this tempo basis stays essentially the same as the DELAY (or FREQ.). This means that when

TEMPO, NOTE, and DELAY (or FREQ.) are synchronized, and you change any of these values, the other parameters will

be re-set in order to maintain the correct relationship. The parameters that are re-set and the calculation method(*

a

) used

are as follows.

If you turn SYNC on

→ NOTE will be set

If you edit DELAY (or FREQ.)

→ NOTE will be set

In this case, the NOTE value is calculated as follows.

NOTE = DELAY (or FREQ.)/(4 x (60/TEMPO))

If you edit NOTE → DELAY (or FREQ.) will be set

In this case, the DELAY (or FREQ.) value is calculated as follows.

DELAY (or FREQ.) = NOTE x 4 x (60/TEMPO)

If you edit TEMPO → DELAY (or FREQ.) will be set

In this case, the DELAY (or FREQ.) value is calculated as follows.

DELAY (or FREQ.) = original DELAY (or FREQ.) x (previous TEMPO/new TEMPO)

Example 1: When SYNC=ON, DELAY=250 ms, TEMPO=120, you change NOTE from 8th note to quarter note

DELAY= new NOTE x 4 x (60/TEMPO)

= (1/4) x 4 x (60/120)

= 0.5 (sec)

= 500 ms

Thus, the DELAY will change from 250 ms to 500 ms.

Example 2: When SYNC=ON, DELAY=250 ms, NOTE=8th note, you change TEMPO from 120 to 121

DELAY= original DELAY x (previous TEMPO/new TEMPO)

= 250 x (120/121)

= 247.9 (ms)

Thus, the TEMPO will change from 250 ms to 247.9 ms.

*

a

Rounded values are used for the calculation results.

• Ranges of the NOTE and TEMPO values

The ranges of the NOTE and TEMPO values are limited by the ranges of the DELAY or FREQ. values. You cannot set

NOTE or TEMPO values that would cause DELAY or FREQ. to exceed their maximum possible values when synchronized

to tempo. This limitation also applies even when SYNC is OFF.

• Special characteristics of the TEMPO parameter

The TEMPO parameter has the following characteristics that are unlike other parameters.

•It is a common value shared by all effects

•It cannot be stored/recalled (the value is not saved)

This means that the TEMPO value may not necessarily be the same when an effect is recalled as when that effect was

stored. Here is an example.

Store the effect: TEMPO=120 → Change TEMPO to 60 → Recall the effect: TEMPO=60

Normally when you change the TEMPO, the DELAY (or FREQ.) will be re-set accordingly. However if the DELAY (or

FREQ.) were changed, the effect would sound differently when recalled than when it was stored. To prevent the effect from

changing in this way between store and recall, the SPX2000 does not update the DELAY (or FREQ.) value when an effect is

recalled, even if the TEMPO is no longer the same as when that effect was stored.

= 1/48

= 2/1

= 1/16

= 1/24

= 1/12

= 3/4

= 3/16

= 1/2

= 3/32

= 1/6

= 1/4

= 1/8

= 1/1

= 3/8

16 SPX2000—Owner’s Manual

Press the [COMPARE] button (I) to compare the origi-

nal effect with the edited version.

→ Each time you press this button, the [COMPARE] LED

will alternate between lit and blinking. The LED will

light if the edited effect is selected, and will blink if the

unedited effect is selected.

Here’s how to specify a location in the USER bank and

store the edited effect.

1 Select the USER bank

Press the [BANK] button (A) several times to select

the USER bank.

→ The [BANK] indicator (A) will indicate “USER.”

2 Select a store-destination for the effect

Use the [▲]/[▼] buttons (C) to specify the effect

number in which you will store the effect you edited.

→ The effect number indicator (0) shows the cur-

rently selected effect number.

3 Store the effect

Press the [STORE] button (B) to store the effect.

→ The [COMPARE] LED (I) will go dark, and the

[UNDO] LED (E) will light.

You can return settings to their prior state by “undoing”

the previous Store, Recall, or Clear Effect operation. You

can also “undo” the previous “undo” operation; this is

called “redo.”

Undo

When the [UNDO] LED (E) is lit, press the [UNDO] but-

ton to undo the previous Store, Recall, or Clear Effect

operation.

→ The [UNDO] LED will blink.

Redo

When the [UNDO] LED (E) is blinking, press the

[UNDO] button to cancel the previous Undo operation.

→ The [UNDO] LED will light.

Check the edited effect

NOTE:

The following buttons are inoperable while the [COMPARE]

LED is blinking.

• [

▲

INC]/[

▼

DEC] buttons (

G

)

• [UTILITY] buttons (

L

)

• [TAP] button (

N

)

Store the effect

Undoing the previous operation

NOTE: Undo/Redo will no longer be available if you switch

parameters.

SPX2000—Owner’s Manual 17

Operation

Other functions

Here’s how to edit the name of the recalled effect. You can

edit the name only for effects in the USER bank.

1 Select the USER bank

Use the [BANK] button (A) to select the USER bank.

2 Select an effect

Select the effect whose name you want to edit, and

recall it (page 12).

3 Select the “TITLE EDIT” function

Press the [UTILITY] button (L) several times to select

“TITLE EDIT.”

4 Edit the effect name

Use the following buttons to edit the effect name.

[BACK] button:

Moves the cursor toward the left.

[NEXT] button:

Moves the cursor toward the right.

[▲ INC] button:

Changes the character at the cursor location (A→B→C).

[▼ DEC] button:

Changes the character at the cursor location (C→B→A).

The effect name can be up to 16 characters long. You can

use the following characters.

You can switch the Protect setting on/off for the recalled

effect. Only effects in the USER bank can be protected. By

turning Protect ON for important effects, you can prevent

them from being overwritten accidentally.

1 Select the USER bank

Use the [BANK] button (A) to select the USER bank.

2 Select an effect

Select the effect whose Protect setting you want to

change, and recall it (page 12).

3 Select the “USER PGM PROTECT” function

Press the [UTILITY] button (L) several times to select

“USER PGM PROTECT.”

4 Turn Protect on or off

Use the [▲ INC]/[▼ DEC] buttons (G) to turn Pro-

tect on/off.

If you turn the setting ON, you will be unable to per-

form the following operations on that effect.

•Store

• Edit the effect name

•Delete

•Change the background color

If you turn the setting OFF, protect will be defeated and

you will again be able to perform Store operations, etc.

Editing the effect name

REV-X LARGE HALL

TITLE EDIT

REV-X LARGE HALL

TITLE EDIT

Cursor

A

R S T U V W X Y Z

ab cd ef g

xy z

[ ¥

!

@

./

0123456789 : ; <=>?

)

+,–

$%& ’ ("#

]

^

`

_

hi jk l m n o

pqr s t uv

w

BC D EFG H I J K L M N O

PQ

Protecting an effect

USER PGM PROTECT

*OFF ON

USER PGM PROTECT

*OFF ON

18 SPX2000—Owner’s Manual

Here’s how to change the background color for the recalled

effect. You can change the background color only for USER

bank effects.

1 Select the USER bank

Use the [BANK] button (A) to select the USER bank.

2 Select an effect

Select the effect whose background color you want to

change, and recall it (page 12).

3 Select the “LCD BACK” function

Press the [UTILITY] button (L) several times to select

“LCD BACK.”

4 Select the display background color

Use the [▲ INC]/[▼ DEC] buttons (G) to select the

display background color.

You can choose one of the following ﬁve colors.

WHITE

CYAN

MAGENTA

YELLOW

GREEN

Selecting the Utility function

Press the [BACK] button

to move to the preceding function.

Press and hold the [BACK] button

to continue moving through the preceding functions.

Press the [NEXT] button or [UTILITY] button

to move to the following function.

Press and hold the [UTILITY] button

to continue moving through the functions.

*For some functions, the [BACK] button and [NEXT] button

are used to move the cursor.

1 Select the “CLOCK SOURCE” function

Press the [UTILITY] button (L) several times to select

“CLOCK SOURCE.”

2 Select the word clock source

Use the [▲ INC]/[▼ DEC] buttons (G) to select the

word clock source.

→ The [CLOCK] indicator (6) and [kHz] indicator (8)

will light according to your selection.

You can choose one of the following six word clock

sources.

• WORD CLOCK: Clock data received from the

[WORD CLOCK IN] jack (V)

• AES/EBU: Clock data received from the [AES/

EBU IN] jack (X)

• INT44.1kHz: Internal clock (44.1 kHz)

• INT48kHz: Internal clock (48 kHz)

• INT88.2kHz: Internal clock (88.2 kHz)

• INT96kHz: Internal clock (96 kHz)

Changing the display back-

ground color

REV-X LARGE HALL

LCD BACK=YELLOW

REV-X LARGE HALL

LCD BACK=GREEN

Selecting the word clock source

NOTE: If the display indicates “WRONG WORD CLOCK!”, the

word clock signal from the external device has either been

interrupted or is a frequency to which the SPX2000 cannot

synchronize. Check whether there might be a problem with the

connection from the device supplying the word clock, or an

incorrect word clock setting.

If this occurs, the word clock source will automatically switch to

one of the SPX2000’s internal clocks until an acceptable word

clock is supplied from the external device.

NOTES:

• The SPX2000 extracts the sampling frequency from the

clock frequency. This means that the word clock frequency =

the sampling frequency.

• When INT44.1 kHz–INT 96 kHz is selected, noise may occur

or the output may be muted if the word clock and the input

signal cannot be synchronized correctly

CLOCK SOURCE

INT96kHz

CLOCK SOURCE

INT96kHz

SPX2000—Owner’s Manual 19

Operation

Here’s how to select either the signal from the [INPUT]

jacks ([) or the signal from the [AES/EBU IN] jack (X)

as the input source.

1 Select the “INPUT SOURCE” function

Press the [UTILITY] button (L) several times to select

“INPUT SOURCE.”

2 Select the input source

Press the [▲ INC] button (G) to select DIGITAL

([AES/EBU IN] jack), or press the [▼ DEC] button

(G) to select ANALOG ([INPUT] jacks).

→ The [INPUT SOURCE] indicator (5) indicates your

selection.

To prevent undesired changes from being made acciden-

tally, you can selectively disable certain operations.

1 Select the “OPERATION LOCK” function

Press the [UTILITY] button (L) several times to select

“OPERATION LOCK.”

2 Select the operation lock level

Use the [▲ INC]/[▼ DEC] buttons (G) to select the

operation lock level.

About word clock

The signal used to synchronize digital audio signal

processing is called “word clock.”

When two or more digital devices are connected in

order to send and receive digital audio signals, each

digital device must process the signal at the same

timing. Even if all connected devices are set to the

same clock frequency, the signals will not be trans-

mitted and received correctly if the processing tim-

ing does not match, or you may hear noise.

In order for digital audio signals to be synchro-

nized, one digital device must transmit the clock

(synchronization data), and the other devices must

be set to receive this clock. In such a setup, the

device that supplies the synchronization reference

clock is called the “CLOCK MASTER,” and the

receiving devices are called “CLOCK SLAVES.”

To use the SPX2000 as the clock master, set the

“CLOCK SOURCE” function (page 18) to either

INT96kHz, INT88.2kHz, INT48kHz, or INT44.1.

To use the SPX2000 as a clock slave, use either of

the following two methods.

1 Set the “CLOCK SOURCE” function

(page 18) to AES/EBU, and connect the

AES/EBU format compatible device supply-

ing the clock data to the [AES/EBU IN] jack

(X).

2 Set the “CLOCK SOURCE” function

(page 18) to WORD CLOCK, and connect

the device supplying the clock to the

[WORD CLOCK IN] jack (V). When doing

so, the device supplying the clock must be

connected one-to-one with the SPX2000.

Selecting the input source

NOTE: If the display indicates “Sync Error!” or if the DIGITAL

[INPUT SOURCE] indicator blinks, the incoming digital input

signal does not match the clock on which the SPX2000 is

operating.

Tr y changing the setting of the device that is supplying the word

clock.

Restricting operation of the

SPX2000

INPUT SOURCE

*ANALOG DIGITAL

INPUT SOURCE

*ANALOG DIGITAL

OPERATION LOCK

*OFF 1 2 3

OPERATION LOCK

*OFF 1 2 3

20 SPX2000—Owner’s Manual

Level 1: Utility functions other than Operation Lock

will be disabled

Level 2: In addition to Level 1, effect store and undo-

ing of store operations will be disabled

Level 3: In addition to Level 2, effect recall and editing

will be disabled

The following table shows the operations that are dis-

abled for each level.

O: Operable X: Inoperable

*1 Only the Operation Lock level can be changed.

*2 If the Operation Lock level is 1 or higher, Utility functions

other than Operation Lock cannot be selected.

Here’s how to erase (clear) the recalled effect. You can only

erase USER bank effects.

You cannot erase the effects in the PRESET bank or CLAS-

SIC bank.

1 Select the USER bank

Use the [BANK] button (A) to select the USER bank.

2 Select an effect

Select the effect that you want to erase (page 12).

3 Select the “U## CLEAR?” function

Press the [UTILITY] button (L) several times to select

“U## CLEAR?” (## will be an effect number).

4 Erase the effect

Press the [▲ INC] button (G) to erase the recalled

effect.

→ When the effect has been erased, the display will

indicate “Completed!”

NOTE: If you attempt to use the front panel buttons to perform

an operation that has been disabled by Operation Lock, a

message of “Operation Locked!” will appear in the display.

However, this message will not appear if such an operation is

attempted by remote control.

OPERATION LOCK

OFF

123

Button operations or equivalent remote control

[INPUT MODE] button (3)

OOOX

[METER] button (4)

OOOO

[BANK] button (A)

OOOX

[STORE] button (B)

OOX X

[▲]/[▼] buttons (C)

OOOX

[RECALL] button (D)

OOOX

[UNDO]

button (E)

Undo of Store opera-

tions

OOX X

Undo of Recall opera-

tions

OOOX

[BACK] button (F)/

[NEXT] button (H)

OOOO

[▲ INC]/

[▼ DEC]

buttons (

G)

Editing of Basic param-

eters and Fine parame-

ters

OOOX

Editing of Utility

settings

O

X

*1

X

*1

X

*1

[PARAMETER] button (J)

OOOO

[FINE PARAM] button (K)

OOOO

[UTILITY] button (L)

O

*2

O

*2

O

*2

[COMPARE] button (I)

OOOX

[BYPASS] button (M)

OOOX

[TAP] button (N)/foot switch

OOOX

[POWER ON/OFF] button (P)

OOOO

MIDI

Note on/off

(Start/stop recording or

playback for Freeze)

OOOO

Erasing an effect

NOTES:

• The effect will be erased when you press the [

▲

INC] button.

After the effect has been erased, you can use the [UNDO]

button (

E

) to recover the erased effect.

• If the display indicates “This Program is Protected!”, the pro-

tect setting has been turned on for that effect. Turn off the

protect setting, and then erase the effect (page 17).

U01 CLEAR?

PUSH INC

Sivu latautuu...

Yamaha SPX2000 Ohjekirja

Yamaha SPX2000 Ohjekirja

muilla kielillä

Aiheeseen liittyviä papereita

Muut asiakirjat