Yamaha DV-C6860 Omistajan opas

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

2006

DV-C6860

DVD CHANGER

LECTEUR DE DVD CHANGEUR

DV-C6860

OWNER’S MANUAL

MODE D’EMPLOI

G

BEDIENUNGSANLEITUNG

Printed in China 3139 245 21861

00cv_DV-C6860_G.fm Page 1 Thursday, March 30, 2006 5:04 PM

i

Important notes for users in the

U.K.

Mains plug

This apparatus is fitted with an approved 13

Amp plug. To change a fuse in this type of plug

proceed as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5 Amp,

A.S.T.A. or BSI approved type.

3 Refit the fuse cover.

If the fitted plug is not suitable for your jack

outlets, it should be cut off and an appropriate

plug fitted in its place.

If the mains plug contains a fuse, this should

have a value of 5 Amp. If a plug without a fuse

is used, the fuse at the distribution board should

not be greater than 5 Amp.

Note: The severed plug must be disposed to avoid

a possible shock hazard should it be inserted into

a 13 Amp jack elsewhere.

How to connect a plug

The wires in the mains lead are coloured with

the following code: blue = neutral (N),

brown = live (L).

● As these colours may not correspond with the

colour markings identifying the terminals in your

plug, proceed as follows:

– Connect the blue wire to the terminal

marked N or coloured black.

– Connect the brown wire to the terminal

marked L or coloured red.

– Do not connect either wire to the earth

terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain

that the cord grip is clamped over the sheath of

the lead - not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require

consent. See Copyright Act 1956 and The

Performer’s Protection Acts 1958 to 1972.

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle

tai muille vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå

utsættelse for stråling.

Bemærk: Netafbryderen STANDBY/ON er

sekundært indkoblet og ofbryder ikke strømmen fra

nettet. Den indbyggede netdel er derfor tilsluttet til

lysnettet så længe netstikket sidder i stikkontakten.

N

Observer: Nettbryteren STANDBY/ON er sekundert

innkoplet. Den innebygdenetdelen er derfor ikke

frakoplet nettet så lenge apparatet er tilsluttet

nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sätt än i

denna bruksanvisning specificerats, kan användaren

utsättas för osynlig laserstrålning, som överskrider

gränsen för laserklass 1.

Observera! Strömbrytaren STANDBY/ON är

sekundärt kopplad och inte bryter inte strömmen från

nätet. Den inbyggda nätdelen är därför ansluten till

elnätet så länge stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa

käyttäjän turvallisuusluokan 1 ylittävälle

näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina

tippu-ja roiskevedelle.

Toiminnanvalitsin STANDBY/ON on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä

sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD OCH SPÄRREN ÄR

URKOPPLAD. BETRAKTA EJ STRÅLEN.

ii

ПРЕДУПРЕЖДЕНИЕ

ПРИ ОТКРЫТИИ УСТРОЙСТВА

ВЫ МОЖЕТЕ ПОДВЕРГНУТЬСЯ ВОЗДЕЙСТВИЮ

ВИДИМОГО И НЕВИДИМОГО ЛАЗЕРНОГО ИЗЛУЧЕНИЯ.

ИЗБЕГАЙТЕ ВОЗДЕЙСТВИЯ ЛУЧА.

LASER SAFETY

This unit employs a laser. Due to possible eye

injury, only a qualified service person should

remove the cover or attempt to service this device.

SECURITE LASER

L’appareil utilise un laser. En raison des risques de

blessure des yeux, le retrait du couvercle ou les

réparations de l’appareil devront être confiés

exclusivement à un technicien d’entretien qualifié.

VORSICHT MIT DEM LASER

Dieses Gerät enthält einen Laser. Um unnötige

Augenverletzungen zu vermeiden, sollten Sie alle

Wartungs- und Reparaturarbeiten einem

qualifizierten Wartungstechniker überlassen.

БЕЗОПАСНОЕ ИСПОЛЬЗОВАНИЕ ЛАЗЕРА

Данное устройство содержит лазер. Из-за

опасности травмирования глаз снимать

крышку или обслуживать данное устройство

должен только сертифицированный

специалист по техническому обслуживанию.

C

L

A

S

1

L

A

S

E

R

P

R

O

D

U

C

T

L

A

S

E

R

K

L

A

S

E

1

P

R

O

D

U

K

T

L

U

O

K

A

N

1

L

A

S

E

R

L

A

I

T

E

K

L

A

S

1

L

A

S

E

R

A

P

A

R

A

T

P

R

O

D

U

I

T

L

A

S

E

R

D

E

C

L

A

S

E

1

CAUTION

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN. AVOID EXPOSURE TO BEAM

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING

UNDGÅ UDSÆTTELSE FOR STRÅLING

ADVARSEL

SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL

ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN

VARNING

SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR

DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN

VA R O !

AVAT TAESSA OLET ALTTIINA NÄKYVÄLLE JA

NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE, ÄLÄ KATSO SÄTEESEEN

VORSICHT

SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN

DANGER

VISIBLE AND INVISIBLE LASER RADIATION WHEN

OPEN AVOID DIRECT EXPOSURE TO BEAM

ATTENTION

RAYONNEMENT LASER VISIBLE ET INVISIBLE EN

CAS D’OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER

This unit emits visible laser radiation when open.

Avoid direct eye exposure to beam.

When this unit is plugged into a wall outlet, do not

place your eyes close to the opening of the disc

tray and other openings or look inside.

DANGER

Risque d'exposition au laser en cas d'ouverture.

Eviter toute exposition au faisceau.

Lorsque cet appareil est branché à la prise de

courant, ne pas approcher les yeux de l'ouverture

du plateau changeur et des autres ouvertures

pour regarder à l'intérieur.

GEFAHR

Sichtbare Laserstrahlen bei geöffneter Abdeckung.

Achten Sie darauf, nicht direkt in den Laserstrahl zu

blicken.

Wenn das Gerät an die Wandsteckdose angeschlossen

ist, halten Sie die Augen von der Öffnung des Disc-

Fachs oder anderen Öffnungen fern, und blicken Sie in

diesem Fall nicht in das Innere des Geräts.

ОПАСНОСТЬ

Данное устройство излучает в открытом

состоянии видимые лазерные лучи. Не

допускайте непосредственного воздействия

лазерных лучей на глаза.

Когда данное устройство подключено к

настенной розетке, не приближайте глаза к

отверстию лотка для диска и других

отверстий и не смотрите на внутренние части.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

ATTENTION

L’emploi de commandes, de réglages ou un choix

de procédures différents des spécifications de

cette brochure peut entraîner une exposition à

d’éventuelles radiations pouvant être dangereses.

ACHTUNG

Die Verwendung von Bedienungselementen oder

Einstellungen oder die Durchführung von

Bedienungsvorgängen, die nicht in dieser

Anleitung aufgeführt sind, kann zu einem Kontakt

mit gefährlichen Laserstrahlen führen.

ПРЕДУПРЕЖДЕНИЕ

Использование органов управления или

настроек или выполнение процедур,

отличных от описанных в данном

руководстве, могут привести к опасному

облучению.

iii

CAUTION: READ THIS BEFORE OPERATING THIS UNIT.

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place — away from direct sunlight, heat sources,

vibration, dust, moisture, or cold. In a cabinet,

allow about 2.5cm (1 inch) of free space all

around this unit for adequate ventilation.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, nor locate this unit in

an environment with high humidity (i.e., a room

with a humidifier) to prevent condensation inside

this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects

may fall onto this unit and/or this unit may be

exposed to liquid dripping or splashing. On the

top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

–

Burning objects (i.e., candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall,

spilling the liquid and causing an electrical

shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation.

If the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use excessive force on switches, knobs

and/or cords.

10 When disconnecting the power cord from the

wall outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than as specified.

13 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reason.

14 When not planning to use this unit for long

periods of time (i.e., vacation), disconnect the AC

power plug from the wall outlet.

15 Be sure to read the “Troubleshooting” section on

common operating errors before concluding that

this unit is faulty.

16 Before moving this unit, press STANDBY/ON to

set the unit in standby mode, and then disconnect

the AC power plug from the wall outlet.

17 Install this unit near the wall outlet and where the

AC power plug can be reached easily.

Be sure to place this unit on a level surface.

If you do not do so, PLAYXCHANGE operation of

this unit will not function correctly, and may damage

the disc(s) and/or this unit itself.

Refer to pages i and ii at the beginning of the

manual for more information.

The unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

LASER

Type Semiconductor laser GaAlAs

Wave length 650 nm (DVD)

780 nm (VCD/CD)

Output Power 7 mW (DVD)

10 mW (VCD/CD)

Beam divergence 60 degree

1 En

English

Contents

Introduction

Region codes ...........................................................................2

Supplied accessories...............................................................2

Notes on discs ........................................................................2

Cleaning discs ..........................................................................2

Patent information.................................................................. 2

Functional Overview

Front panel...............................................................................3

Rear panel ................................................................................ 4

Remote control.......................................................................5

Connections

General notes on connections............................................ 6

Audio connections .................................................................6

Digital connection................................................................................6

Analog connection..............................................................................6

Video connections..................................................................7

SCART terminal <A>.......................................................................7

Component video jacks <B>.......................................................7

Composite video jack <C>...........................................................7

Getting Started

Inserting batteries into the remote control.....................8

Using the remote control ...............................................................8

Turning on the power........................................................... 9

About the auto standby function ...............................................9

Setting a TV type and display...............................................9

Setting a color system for your TV ...........................................9

Setting an aspect ratio for your TV........................................ 10

Setting a language preference ............................................11

Setting the OSD language ...........................................................11

Setting the audio, subtitle and disc menu languages.....11

Disc Operations

Basic playback........................................................................12

General operation................................................................12

Pausing playback................................................................................12

Selecting a track/chapter...............................................................13

Searching backward/forward......................................................13

Stopping playback............................................................................. 13

Selecting the various repeat/shuffle functions................13

Repeat.....................................................................................................13

Repeating a section within a chapter/track........................14

Shuffle (except DVD/VCD/SVCD)........................................14

Operations for video playback (DVD/VCD/SVCD).....14

Using the disc menu........................................................................14

Slow motion ........................................................................................14

Zooming in...........................................................................................15

Resuming playback from the last stopped point.............15

On-screen display (OSD)............................................................15

Special DVD features .......................................................... 16

Playing by title.....................................................................................16

Camera angle......................................................................................16

Audio.......................................................................................................17

Subtitles..................................................................................................17

Special VCD & SVCD features ......................................... 17

Playback control (PBC) .................................................................17

Audio CDs............................................................................. 17

Playing by discs................................................................................... 17

Playing MP3/JPEG/Kodak picture CDs............................ 17

General operation............................................................................ 17

Selecting a folder and track/file................................................. 18

Special picture disc features .............................................. 18

Preview function (JPEG) ...............................................................18

Zooming pictures ............................................................................. 18

Playback with multi-angles...........................................................18

Scan effect............................................................................................. 19

Playing MP3 music and JPEG pictures simultaneously...19

Setup Menu

General setup menu............................................................ 20

Locking/Unlocking the disc for viewing................................ 20

Dimming the front panel display..............................................20

Programming disc tracks and discs ......................................... 20

OSD language..................................................................................... 22

Screen saver......................................................................................... 22

Sleep timer ...........................................................................................22

Audio setup menu................................................................ 22

Setting the analog output............................................................. 23

Setting the digital output.............................................................. 23

CD upsampling .................................................................................. 24

Night mode..........................................................................................24

Video setup menu................................................................ 24

TV type...................................................................................................24

Setting the TV display .................................................................... 25

Progressive............................................................................................ 26

Picture settings ...................................................................................26

Switching the YUV/RGB...............................................................27

Preference setup menu....................................................... 27

Audio, subtitle and disc menu................................................... 28

Restricting playback with parental control ......................... 28

PBC (Playback control) .................................................................28

MP3/JPEG menu................................................................................ 28

Changing the password.................................................................29

Resetting the system....................................................................... 29

Language Code .......................... 30

Troubleshooting ........................ 32

Glossary ...................................... 34

Specifications ............................. 35

2 En

Introduction

Thank you for purchasing this unit. This

Owner’s Manual explains the basic

operation of this unit.

DVD discs must be labeled ALL

regions or Region 2 in order to

play on this unit.

You cannot play discs labeled for

other regions.

– Remote control

– Two batteries (AA, R06, UM-3) for the

remote control

– Audio pin cable

– Video pin cable

– Owner’s Manual

– This unit is designed for use with the

following discs: DVD-Video, Video CD,

Super Video CD, Audio CD, CD-R,

CD-RW, DVD+RW, DVD+R, DVD-R

and DVD-RW.

– This unit can play:

– MP3 and picture (Kodak, JPEG) files

recorded on CD-R(W).

– JPEG/ISO 9660 format

– Maximum 30 characters per display

– CD-R and CD-RW cannot be played

unless finalized.

– Some discs cannot be played depending

on the recording conditions, such as the

PC environment and application

software. The characteristics and

conditions of some discs (materials,

scratches, curvature, etc.) may result in

playback failure.

– Be sure to use only CD-R and CD-RW

discs made by reliable manufacturers.

– Do not use any non-standard shaped

discs (heart-shaped, etc.).

– Do not use discs with tape, seals, or

paste on their surface. Doing so may

damage this unit.

– Do not use discs affixed with labels

printed by a commercially available label

printer.

• When a disc becomes dirty, clean it

with a cleaning cloth. Wipe the disc

from the center out. Do not wipe in a

circular motion.

• Do not use solvents such as benzine,

thinner, commercially available cleaners,

or antistatic spray intended for analog

records.

Manufactured under license from

Dolby Laboratories. “Dolby”,

“Pro Logic” and the double-D

symbol are trademarks of Dolby

Laboratories.

“DTS” and “DTS Digital Out” are

trademarks of Digital Theater

Systems, Inc.

Region codes

Supplied accessories

Notes on discs

ALL

2

Cleaning discs

Patent information

This product incorporates copyright protection

technology that is protected by method claims

of certain U.S. patents and other intellectual

property rights owned by Macrovision

Corporation and other rights owners. Use of

this copyright protection technology must be

authorized by Macrovision Corporation, and is

intended for home and other limited viewing

uses only unless otherwise authorized by

Macrovision Corporation. Reverse engineering

or disassembly is prohibited.

3 En

English

Functional Overview

1 Disc tray

Loads up to 5 discs in the disc tray.

2 / (OPEN/CLOSE)

Opens or closes the disc tray.

3 PLAYXCHANGE

Reloads or unloads discs without

interrupting current disc playback.

4 9 (STOP)

Stops playback.

5 B/; (PLAY/PAUSE)

Starts or pauses playback.

6 R/T

Searches forward.*

Moves to the next chapter or track.

7 S/Q

Searches backward.*

Moves to the previous chapter or track.

8 Front panel display

Shows the current status of this unit.

9 DISC (1, 2, 3, 4, 5) / LEDs

Selects and directly plays back the preferred

disc.

Each LED lights up in orange when this unit

recognizes that the corresponding disc has

been loaded.

0 STANDBY/ON

Turns on this unit or sets it to the standby

mode.

While this unit is in the standby mode, it

consumes a small amount of power.

* Press the button for about two seconds.

Front panel

1

2

9

0

8

67

5

4

3

4 En

Functional Overview

1 AUDIO OUT (L, R) jacks

Connect to the audio input jacks of your

AV receiver or stereo system.

2 DIGITAL OUT - COAXIAL jack

Connect to the coaxial input jack of your

AV receiver.

3 VIDEO OUT - COMPONENT

(Y, PB/CB, PR/CR) jacks

Connect to the component input jacks of

your AV receiver.

4 AV terminal

Connect to SCART input terminal of your

TV.

5 VIDEO OUT - VIDEO jack

Connect to the composite video input jack

of your AV receiver.

6 AC power cord

Connect to a standard AC outlet.

Caution: Do not touch the inner pins of the jacks on the rear panel of this unit.

Electrostatic discharge may cause permanent damage to this unit.

Rear panel

AUDI O

OUT

DIGITAL

OUT

VIDEO OUT

VIDEO

COAXIAL COMPONENT

Y

P

B /CB

PR /CR

3

6

4

1

5

2

5 En

English

Functional Overview

1

Turns on this unit or sets it to the

standby mode.

2 TOP MENU/RETURN

Displays the top-level disc menu (DVD).

Moves back to the previous menu (DVD*/

VCD).

3 MENU

Accesses the menu of a disc (DVD).

Switches PBC on or off (VCD).

4 1 / 2/3 / 4

Selects an item in the currently displayed

menu. Search or slow playback.

ENTER/OK

Confirms the menu selection.

5 S

Searches backward.*

Moves to the previous chapter or track.

6 STOP (9)

Stops playback.

7 SUBTITLE

Selects the subtitle language.

8 ANGLE

Selects the DVD camera angle.

9 REPEAT

Repeats the chapter, track, title, disc or

all discs.

0 A-B

Repeats a specific segment.

q Numeric buttons (0-9)

Selects numbered items in the currently

displayed menu.

w ON SCREEN

Accesses or exits from the on-screen

display (OSD) menu of this unit.

e SETUP

Accesses or exits from the setup menu

of this unit.

r T

Searches forward.*

Moves to the next chapter or track.

t PLAY (B)

Starts playback.

y PAUSE (;)

Pauses playback temporarily.

Frame-by-frame playback.

u AUDIO

Selects the audio language or format.

i ZOOM

Enlarges the video image.

o DISC SKIP

Selects another disc.

p SHUFFLE

Plays tracks in a random order.

* Press and hold the button for about two

seconds.

Remote control

MENU SETUP

ENTER

OK

STOP

ANGLE

A B

PAUSE

PLAY

1

2

3

4

5

6

7

8

0

9

TOP MENU RETURN

ON SCREEN

DVD

ZOOM AUDIO

SUBTITLE

REPEAT

SHUFFLE

DISC SKIP

1

2

3

4

7

8

9

0

5

6

q

w

e

r

t

y

u

i

o

p

6 En

Connections

Be sure to turn off this unit and unplug the

power supply cable before you make or

change connections.

• Depending on the component you wish

to connect, there are various ways to

make connections. Possible connections

are described below.

• Refer to the manuals of your other

components as necessary to make the

best connections.

• Do not connect this unit via your VCR.

The video quality could be distorted by

the copy protection system.

• Do not connect the audio out jack of

this unit to the phono in jack of your

audio system.

Digital connection

This unit has a coaxial digital out jack.

Connect DIGITAL OUT - COAXIAL jack

of this unit to your AV receiver equipped

with a Dolby Digital, DTS, or MPEG

decoder using a commercially available

coaxial cable.

You need to set “DIGITAL

OUTPUT” to “ALL” (see “DIGITAL

OUTPUT” on page 23).

Notes:

– If the audio format of the digital output

does not match the capabilities of your

receiver, the receiver produces a distorted

sound or no sound at all. Make sure to

select the appropriate audio format from

the menu screen on the disc.

Pressing AUDIO on the remote control once

or more may change not only the audio

language but also the audio format. The

selected format appears in the front panel

display for several seconds.

– If you wish to enjoy Dolby Digital, DTS, and

MPEG formats, you must connect this unit

to an AV receiver that supports these

formats.

Analog connection

This unit has analog output jacks.

Connect AUDIO OUT (L, R) jacks of this

unit to the corresponding input jacks of

your audio component (such as a stereo

amplifier) using the supplied audio cable.

General notes on connections

Audio connections

AUDI O

OUT

DIGITAL

OUT

VIDEO OUT

VIDEO

COAXIAL COMPONENT

Y

P

B/CB

PR/CR

COAXIAL

IN

C

AV receiver

Speakers

This unit

AUDI O

OUT

DIGITAL

OUT

VIDEO OUT

VIDEO

COAXIAL COMPONENT

Y

P

B/CB

PR/CR

CD/DVD

RL

L

R

L

Right

speaker

Left

speaker

Stereo

amplifier

This unit

Audio pin cable

(supplied)

7 En

English

Connections

If your AV receiver has video output jacks,

connect your receiver and then your TV

so that you can use one TV for several

different video sources (LD, VCR, etc.) by

simply switching the input source selector

of your AV receiver.

This unit has three types of video output

jacks. Use the one that corresponds to the

input jacks of the component to be

connected.

SCART terminal <A>

If your TV has only a terminal for video

input, you can connect the TV directly to

this unit.

Connect AV terminal of this unit to

SCART input terminal of your TV using a

commercially available SCART cable.

Note:

– Ensure that the “TV” indication on SCART

cable is connected to the TV set and “DVD”

indication on SCART cable is connected to

this unit.

Component video jacks <B>

Component video connections achieve

higher fidelity color reproduction than

S-video connections by transmitting video

signals on separate wires for luminance

(Y: green) and chrominance (P

B: blue,

P

R: red).

Connect VIDEO OUT - COMPONENT

(Y, P

B/CB, PR/CR) jacks of this unit to

component input jacks of your AV receiver

and then to those of your TV using a

commercially available component cable.

Observe the color of each jack when you

make connections. If your AV receiver

does not have component output jacks,

you can achieve a better video image by

connecting the component output jacks of

this unit directly to the component input

jacks of your TV.

Composite video jack <C>

Connect VIDEO OUT - VIDEO jack of this

unit to the video input jack of your AV

receiver and then to that of your TV using

the supplied video cable.

Video connections

AUDI O

OUT

DIGITAL

OUT

VIDEO OUT

VIDEO

COAXIAL COMPONENT

Y

PB/CB

PR/CR

S VIDEO

OUT

S VIDEO

IN

COMPONENT

VIDEO OUT

COMPONENT

VIDEO IN

VIDEO

OUT

VIDEO

IN

COMPONENT

VIDEO

YPB/CBPR/CR

V

PR

PB

Y

PR

PB

Y

AV receiver

This unit

TV

Video pin

cable

(supplied)

8 En

Getting Started

1 Open the battery compartment.

2 Insert the two supplied batteries (AA, R06,

UM-3) following the indications (+/–)

inside the compartment.

3 Close the cover.

Notes:

– Insert batteries correctly according to the

polarity markings (+/–). The batteries

inserted in the opposite direction may leak.

– Replace the exhausted batteries

immediately with new ones to prevent a

leakage.

– Remove the batteries from the

compartment if the remote control is not

used for more than a month.

– If the batteries have leaked, dispose of

them immediately. Avoid touching the

leaked material or letting it come into

contact with clothing, etc. Clean the battery

compartment thoroughly before installing

new batteries.

– Do not use old batteries together with new

ones.

– Do not use different types of batteries (such

as alkaline and manganese batteries)

together. Read the packaging carefully as

these different types of batteries may have

the same shape and color.

– Dispose of the batteries correctly in

accordance with your local regulations.

Using the remote control

Handling the remote control

• Do not spill water or other liquids on

the remote control.

• Do not drop the remote control.

• Do not leave or store the remote

control in the following types of

conditions:

– places of high humidity, such as near a

bath

– places of high temperature, such as near

a heater or stove

– places of extremely low temperatures

– dusty places

Step 1: Inserting batteries

into the remote control

2

1

3

2

30°

Remote control

sensor

Point the remote control at

the remote control sensor,

within approximately 6 m

(20 ft) from the unit.

9 En

English

Getting Started

1 Connect the AC power cord to an AC

outlet.

2 Turn on your TV and AV receiver.

3 Select the appropriate input source of the

AV receiver connected to this unit. Refer

to the manual supplied with your AV

receiver for details.

4 Turn on this unit.

5 Set the TV to the correct Video IN channel

(e.g. EXT1, EXT2, AV1, AV2, AUDIO/

VIDEO, etc. Refer to the manual supplied

with your TV for details).

➜ The front panel display lights up and the

default screen appears on the TV.

About the auto standby function

This unit is automatically set to the standby

mode when disc playback is stopped or

paused for more than 30 minutes.

When “SCREEN SAVER” is set to

“ON” (see page 22):

The background is displayed when disc

playback is stopped or the paused picture

is displayed for 15 minutes.

The screen saver is displayed for another 15

minutes.

This unit is set to the standby mode.

When “SCREEN SAVER” is set to

“OFF” (see page 22):

The background or the paused picture is

displayed for 30 minutes.

This unit is set to the standby mode.

Setting a color system for your

TV

This unit is compatible with both NTSC

and PAL video formats. Select the color

system that matches your TV.

1 Press SETUP.

2 Press 2 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 3

/ 4 to highlight [TV TYPE], and

then press 2.

4 Press 3

/ 4 to highlight one of the following

options.

Step 2:

Turning on the power

OR

Example of a

paused picture

Background

Step 3: Setting a TV type and

display

VIDEO SETUP PAGE

TV TYPE PAL

TV DISPLAY MULTI

PROGRESSIVE NTSC

PICTURE SETTING

COMPONENT

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

10 En

Getting Started

PAL

Select this if the connected TV is a PAL

system TV. It will change the video signals

of NTSC discs and output them in PAL

format.

MULTI

Select this if the connected TV is

compatible with both NTSC and PAL

formats (such as a multi-system TV). The

output format will be in accordance with

the video signals of the disc.

NTSC

Select this if the connected TV is an NTSC

system TV. It will change the video signals

of PAL discs and output them in NTSC

format.

5 Select an item, and then press

ENTER/OK to confirm your selection.

Notes:

– Before changing the current TV

standard setting, ensure that your TV

supports the selected TV type.

– If the picture is not displayed

properly on your TV, wait for 15

seconds for this unit to activate

automatic recovery.

Setting an aspect ratio for your

TV

You can set the aspect ratio of this unit to

match your TV. If the aspect ratio of your

TV is 4:3, you do not need to change this

setting. If you have a widescreen TV,

change this setting according to the

following procedure.

For details, see “Setting the TV display” on

page 25.

1 Press SETUP.

2 Press 2 repeatedly to select “VIDEO

SETUP PAGE”.

3 Press 3

/ 4 to highlight [TV DISPLAY], and

then press 2.

4 Press 3

/ 4 to highlight [16:9], and then

press ENTER/OK to confirm the

selection.

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

CHANGING PAL TO NTSC:

1. ENSURE THAT YOUR TV SUPPORTS

NTSC STANDARD.

2. IF THERE IS A DISTORTED PICTURE

DISPLAYED ON THE TV, WAIT 15

SECONDS FOR AUTO RECOVER.

CANCELOK

VIDEO SETUP PAGE

TV TYPE

TV DISPLAY 4:3 PAN SCAN

PROGRESSIVE 4:3 LETTER BOX

PICTURE SETTING 16:9

COMPONENT

11 En

English

Getting Started

You can select your own preferred

language settings. This unit automatically

switches to your preferred language

whenever you load a disc. If the selected

language is not available on the disc, the

default language of the disc will be used

instead. The OSD language in the system

menu remains once selected.

Setting the OSD language

1 Press SETUP.

2 Press 1 / 2 to select “GENERAL SETUP

PAGE”.

3 Press 3

/ 4 to highlight [OSD

LANGUAGE], and then press 2.

4 Press 3

/ 4 to select a language, and then

press ENTER/OK to confirm your

selection.

Setting the audio, subtitle and

disc menu languages

1 Press STOP (9) twice, and then press

SETUP.

2 Press 2 repeatedly to select

“PREFERENCE PAGE”.

3 Press 3

/ 4 to highlight one of the options

below at a time, and then press 2.

– AUDIO (audio language)

– SUBTITLE (subtitle language)

– DISC MENU (disc menu language)

4 Press 3

/ 4 to select a language, and then

press ENTER/OK to confirm your

selection.

If the language you want is not in the

list, select [OTHERS],

and then use the numeric buttons (0-9)

on the remote control to enter the 4-digit

language code (see “Language Code” on

page 30), and then press ENTER/OK to

confirm the code.

5 Repeat steps 3–4 for other language

settings.

Step 4: Setting a language

preference

GENERAL SETUP PAGE

DISC LOCK ENGLISH

DISPLAY DIM DEUTSCH

PROGRAM FRANÇAIS

OSD LANGUAGE ITALIANO

SCREEN SAVER NEDERLANDS

SLEEP POLSKI

РУССКИЙ

TÜRKÇE

PREFERENCE PAGE

AUDIO ENGLISH

SUBTITLE CHINESE

DISC MENU FRENCH

PARENTAL SPANISH

PBC PORTUGUESE

MP3/JPEG NAV POLISH

PASSWORD ITALIAN

DEFAULT TURKISH

TIPS: To return to the previous menu, press 1.

To exit from the menu, press SETUP.

12 En

Disc Operations

IMPORTANT!

– If the inhibition icon ( or X)

appears on the TV screen when a

button is pressed, the function for

that button is not available on the

current disc or at the current time.

– Depending on the DVD or VIDEO

CD disc, some operations may

operate differently or be

restricted.

– Do not push on the disc tray or put

any objects other than discs on the

disc tray. Doing so may cause the

disc player to malfunction.

1 Press STANDBY/ON on the front panel

or on the remote control.

2 Press /

(OPEN/CLOSE) on the front

panel to open the disc tray.

3 Place discs in the disc tray with the printed

side up.

4 Press B/;

(PLAY/PAUSE) on the front

panel or PLAY (B) on the remote

control.

➜ The disc tray closes and playback starts

automatically for all of the loaded discs

in the tray in sequence.

5 To stop playback, press 9

(STOP) on the

front panel or STOP (9) on the remote

control.

• To play back a specific disc directly,

press DISC SKIP repeatedly on the

remote control or press DISC (1, 2, 3,

4, 5) on the front panel.

• Press PLAYXCHANGE on the front

panel to open the disc tray, and then

reload or unload discs without

interrupting current disc playback.

• Playback stops after all discs have been

played.

• When the disc tray is open, press

B/;

(PLAY/PAUSE),

/

(OPEN/CLOSE),

PLAYXCHANGE or

DISC (1, 2, 3, 4, 5) to close the disc

tray automatically.

Unless stated otherwise, all operations

described here are carried out using the

supplied remote control.

Pausing playback

1 During playback, press PAUSE (;).

➜ Playback is paused and the sound is

muted.

2 Press PAUSE (;) again to select the next

picture frame.

3 To resume normal playback, press

PLAY (B).

Basic playback

General operation

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

13 En

English

Disc Operations

Selecting a track/chapter

• Press S / T or use the numeric

buttons (0-9) to select a track/chapter

number.

• During repeated playback of a track/

chapter, press S / T to replay the

same track/chapter.

Searching backward/forward

1 Press and hold S / T or press 1 / 2.

2 While searching, press S / T or

1

/ 2 repeatedly to select the desired

speed.

3 To resume normal playback, press

PLAY (B).

Notes:

– 1

/ 2 key may not be available with some

discs.

– For MP3 and WMA, the search function

allows you to search the track currently

being played.

Stopping playback

• Press STOP (9).

Repeat

Repeating chapter/title/disc (DVD)

Each time you press REPEAT, the display

changes as follows:

CHAPTER*: repeats the current

chapter

TITLE: repeats the current title

DISC*: repeats the entire disc

ALL DISC*: repeats all discs loaded

in the tray

REPEAT OFF: exits from the repeat mode

* This feature may not be available with some

discs.

Repeating track/disc (except DVD)

Each time you press REPEAT, the display

changes as follows;

TRACK: repeats the current track

DISC: repeats the entire disc

ALL DISC: repeats all discs loaded in

the tray

REPEAT OFF: exits from the repeat mode

Notes:

– When only one disc is available in the disc

tray, it is continuously played when

ALL DISC is selected.

– For VCD, repeat playback is not available

when the PBC mode is selected.

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

Selecting the various repeat/

shuffle functions

CHAPTER TITLE

REPEAT OFF

ALL DISC DISC

TRACK DISC

REPEAT OFF ALL DISC

14 En

Disc Operations

Repeating a section within a

chapter/track

1 While playing a disc, press A-B at the

desired starting point.

2 Press A-B again at the desired end point.

•A and B can only be set within the same

chapter/track.

➜ The selected section repeats

continuously.

3 To exit from the sequence, press A-B.

Shuffle (except DVD/VCD/SVCD)

With the shuffle function, you can play

tracks in a random order.

1 During playback, press SHUFFLE

repeatedly to select between SHUFFLE

DISC, SHUFFLE ALL DISC, and SHUFFLE

OFF.

➜ The selected mode appears in the front

panel display for several seconds.

• In the SHUFFLE DISC mode, all tracks

on the disc currently playing are played

in a random order.

• In the SHUFFLE ALL DISC mode, tracks

from all discs are played in a random

order:

– If the disc currently playing is a CD, only

tracks from CDs will be played.

– If the disc currently playing is formatted

in MP3 or WMA, tracks on the disc

currently playing are played in a random

order. When all the tracks on that disc

have been played, shuffle playback

continues with the next disc.

Using the disc menu

Depending on the disc, a menu may appear

on the TV screen once you load the disc.

To select a playback feature or item

• Use

1 / 2/3 / 4 or the numeric

buttons (0-9) on the remote control,

and then press ENTER/OK to start

playback.

To access or exit from the menu

• Press MENU on the remote control.

Slow motion

You can play back in slow motion.

1 Press 3 for reverse slow motion or 4 for

forward slow motion.

2 During slow motion, press 3

/ 4

repeatedly to select the desired speed.

3 To resume normal playback, press

PLAY (B).

Note:

– Reverse slow motion is not available for

VCDs and SVCDs.

Operations for video playback

(DVD/VCD/SVCD)

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

15 En

English

Disc Operations

Zooming in

This function allows you to enlarge or

lessen the picture on the TV screen and

pan through the enlarged picture.

1 During playback, press ZOOM repeatedly

to display the picture at different scales.

• Use

1 / 2/3 / 4 to pan through the

enlarged picture.

➜ Playback continues.

2 Press ZOOM repeatedly to return to the

original size.

Resuming playback from the last

stopped point

You can resume playback of the last 10

discs, even if the discs were ejected or the

power of this unit was turned off.

1 Load one of the last 10 discs.

➜ “LOADING #” (#: the disc tray number

(1-5)) appears on the TV screen.

2 Press PLAY (B) while “LOADING #” is

displayed on the TV screen.

➜ “RESUME PLAY” appears on the TV

screen and the disc is played back from

the last point.

To cancel the resume mode

• When playback is stopped, press

STOP (9) again.

On-screen display (OSD)

The OSD menu shows disc playback

information (e.g., the title or chapter

number, elapsed playing time or audio/

subtitle language). A number of operations

are possible without interrupting disc

playback.

1 During playback, press ON SCREEN.

➜ A list of available disc information

appears on the TV screen.

DVD

VCD/SVCD

2 Press 3 / 4 to view the information, and

then press ENTER/OK to access the

selected item.

3 Use the numeric buttons (0-9) to input

the number/time or press 3

/ 4 to make a

selection, and then press ENTER/OK to

confirm the selection.

➜ Playback changes to the selected time

or to the selected title/chapter/track.

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

MENU

TITLE 02/14

CHAPTER 02/14

AUDIO 5.1CH

SUBTITLE ENG

BITRATE 16 TITLE ELAPSED 0:02:25

MENU

TRACK 02/14

DISC TIME 0:49:17

TRACK TIME 0:03:43

REPEAT OFF

BITRATE 16 TOTAL ELAPSED 0:02:25

16 En

Disc Operations

Title/Chapter/Track selection

(DVD/VCD)

1 Press 3

/ 4 to select [TITLE] or

[CHAPTER] (DVD) or [TRACK] (VCD).

2 Press ENTER/OK to confirm the

selection.

3 Select a title, chapter or track number

using the numeric buttons (0-9).

Time search (DVD/VCD)

1 Press 3

/ 4 to select [TT TIME] or [CH

TIME] (DVD) or [TRACK TIME] or [DISC

TIME] (VCD).

• [TT TIME] refers to the total time of the

current title, and [CH TIME] refers to

the total time of the current chapter.

2 Press ENTER/OK to confirm the

selection.

3 Enter hours, minutes and seconds from left

to right using the numeric buttons (0-9)

(e.g. 0:34:27).

Audio/Subtitle/Angle (DVD)

You can change [AUDIO], [SUBTITLE] or

[ANGLE] if these functions are available on

the disc you are playing.

1 Press 3

/ 4 to select [AUDIO],

[SUBTITLE] or [ANGLE].

2 Press ENTER/OK to confirm the

selection.

3 For Audio and Subtitle:

Press 3

/ 4 to highlight your selection, and

then press ENTER/OK.

OR

For Angle:

Select an angle using the numeric

buttons (0-9).

Repeat/Time display (DVD/VCD)

1 Press 3

/ 4 to select [REPEAT] or [TIME

DISP.].

2 Press ENTER/OK to confirm the

selection.

3 Press 3

/ 4 to highlight your selection, and

then press ENTER/OK.

Time display (CD)

Each time you press ON SCREEN, the

time display changes as follows:

Playing by title

1 Press MENU.

➜ The disc title menu appears on the TV

screen.

2 Use

1 / 2/3 / 4 or the numeric buttons

(0-9) to select a playback option.

3 Press ENTER/OK to confirm your

selection.

Camera angle

• Press ANGLE repeatedly to select the

desired angle.

TIPS: The operating features described here might not be possible for certain discs.

Always refer to the instructions supplied with the disc.

Special DVD features

TOTAL ELAPSED TOTAL REMAIN

SINGLE REMAIN SINGLE ELAPSED

Sivu latautuu ...

Yamaha DV-C6860 Omistajan opas

Yamaha DV-C6860 Omistajan opas

muilla kielillä

Liittyvät paperit

Muut asiakirjat