Yamaha R-N301 Ohjekirja

Printed in Malaysia ZN43970

Network Receiver

Réseau Ampli-Tuner

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

_R-N301_G_cv.fm Page 1 Wednesday, July 16, 2014 4:29 PM

i En

English

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord

disconnected from a wall outlet or the unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15

When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press A downward to turn off this

unit and then disconnect the AC power plug from the AC wall

outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the

outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the system off, then leave this unit alone for

cooling.

20 Install this unit near the wall outlet and where the AC power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

This label is required to be attached to a product of which the

temperature of the top cover may be hot during operation.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

Caution: Read this before operating your unit.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you set this unit to

standby mode by A. In this state, this unit is designed to consume a

very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or

coloured RED.

Make sure that neither core is connected to the earth terminal

of the three pin plug.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

English

INTRODUCTION

What you can do with this unit ................................. 2

Sources that can be played back on this unit ................. 2

Devices that can control this unit................................... 3

Operations from your mobile device ............................. 3

Supplied accessories ................................................... 4

Controls and functions ............................................... 5

Front panel ..................................................................... 5

Front display .................................................................. 6

Rear panel ...................................................................... 7

Remote control............................................................... 8

Using the remote controls.............................................. 9

PREPARATION

Connections ............................................................... 10

Connecting speakers and source components.............. 10

Connecting the speakers .............................................. 11

Connecting the FM and AM antennas ......................... 12

Connecting to a network.............................................. 13

Connecting power cable .............................................. 13

Setup of your network devices .................................... 14

BASIC OPERATION

Playback .................................................................... 15

Playing a source........................................................... 15

Using the sleep timer ................................................... 16

Listening to FM/AM radio....................................... 17

FM/AM tuning............................................................. 17

Automatic preset tuning (FM stations only)................ 18

Manual tuning preset ................................................... 18

Recalling a preset station ............................................. 19

Clearing a preset station............................................... 19

Radio Data System tuning ........................................... 20

Using the Spotify service .......................................... 21

Playing back music stored on media servers

(PCs/NAS) ............................................................. 22

Setting the media sharing of music files...................... 22

Playback of PC music contents.................................... 23

Listening to Internet radio....................................... 25

Registering favorite Internet radio stations

(bookmarks)............................................................. 26

Playing back iPod/iTunes music via a network

(AirPlay) ................................................................ 27

Playback of iPod/iTunes music contents ..................... 27

Switching information on the front display ........... 29

ADVANCED OPERATION

Configuring playback settings for different

playback sources (Option menu) .........................30

Option menu items....................................................... 30

Configuring various functions (Setup menu) .........32

Setup menu items......................................................... 32

Network Setup ............................................................. 33

Tone Control................................................................ 34

Balance ........................................................................ 34

Max Volume ................................................................ 34

Initial Volume.............................................................. 34

DC OUT ...................................................................... 34

Configuring the system settings

(ADVANCED SETUP menu)...............................35

ADVANCED SETUP menu items .............................. 35

Restoring the default settings (INIT)........................... 35

Updating the firmware (UPDATE) ............................. 35

Checking the firmware version (VERSION)............... 35

Updating the unit’s firmware via the network.......36

ADDITIONAL INFORMATION

Troubleshooting.........................................................37

Error indications on the front display.....................41

Trademarks ...............................................................42

Specifications .............................................................43

Index...........................................................................44

(at the end of this manual)

Information about third party software licenses

... i

Contents

• y indicates a tip for your operation.

• This manual explains operations using the supplied remote control.

• This manual describes all the “iPod”, “iPhone” and “iPad” as the “iPod”. “iPod” refers to “iPod”, “iPhone” and “iPad”, unless

otherwise specified.

What you can do with this unit

2 En

This unit is a network receiver, on which you can enjoy playing back music files stored on your media server (PC or

NAS), audio contents on the Internet radio, Spotify, AirPlay devices (iPod/iTunes) by connecting the unit to your home

network (DLNA) and audio system on the same network.

* You need a commercially available Wi-Fi broadband router when you use an iPod/Android.

1 Play back the Internet radio (p.25)

2 Play back music files stored on your PC (p.22)

3 Play back music files stored on your NAS

(p.22)

4 Play back your iPod with AirPlay (p.27)

5 Play back the Spotify service (p.21)

6 Play back your external component (p.10)

7 Listening to FM/AM radio (p.17)

y

For details on connecting the devices, see “Connections” (p.10).

What you can do with this unit

Sources that can be played back on this unit

FM/AMFM/AM

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

This unit (R-N301)

1 Internet

Modem

Broadband router*

2 PC

3 NAS

4 iPod (AirPlay)*

5 iPod/Android (Spotify)*

6 CD player etc.

7

INTRODUCTION

What you can do with this unit

3 En

INTRODUCTION

English

* You need a commercially available Wi-Fi broadband router when you use a mobile device.

A Control this unit using your mobile devices (p.3).

B Control this unit using the remote control.

Once you install the app “NETWORK PLAYER CONTROLLER” in your mobile device, you can operate the unit with

the mobile device.

Features

• Power-on/off or other basic operation

• Changing the music source

• Selecting, playing back, and stopping songs

• Playing back songs stored in devices

For downloading the app or the latest information, access to the App Store or Google Play and search “NETWORK

PLAYER CONTROLLER.”

Devices that can control this unit

Operations from your mobile device

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

Broadband router*

Mobile device*

(iPod, Android)

Remote control

Supplied accessories

4 En

Check that the following accessories are supplied with the product.

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert batteries according to the polarity markings (+ and -).

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these

different types of batteries may have the same shape and color.

• Before inserting new batteries, wipe the battery compartment clean.

• Keep the batteries in a location out of reach of children. Batteries can be dangerous if a child were to put in his or her mouth.

• If the batteries grow old, the effective operation range of the remote control decreases considerably. If this happens, replace the

batteries with new one as soon as possible.

• If you plan not to use the unit for a long period of time, remove the batteries from the unit. Otherwise, the batteries will wear out,

possibly resulting in a leakage of battery liquid that may damage the unit.

• Do not throw away batteries with general house waste. Dispose of them correctly in accordance with your local regulations.

Supplied accessories

SETUP

POP-UP MENU

AM

FM

MODE

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

TUNER

CD

PRESET

TUNING

DIMMER

SLEEP

BA

SPEAKERS

HOME

NOW PLAYING

MUTE

OPTION

DISPLAY REPEAT SHUFFLE

VOLUME

RETURN

ENTER

Remote control

FM antennaAM antenna

Batteries (x2)

(AAA, R03, UM-4)

Controls and functions

5 En

INTRODUCTION

English

1 A (power)

Turns on/off (standby) the unit.

In standby mode, this unit consumes a small amount of power to

receive infrared signals from the remote control.

2 PHONES jack

Outputs audio to your headphones for private listening.

3 SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the rear

panel each time the corresponding button is pressed.

4 DISPLAY

Selects the information displayed on the front display

(p.29).

5 Remote control sensor

Receives infrared signals from the remote control.

6 STANDBY/ON indicator

Lights up as follows:

Brightly lit: Power is on

Dimly lit: Standby mode

7 FM MODE

Set the FM band reception mode to automatic stereo or

monaural (p.17).

8 MEMORY

Stores the current FM/AM station as a preset when

TUNER is selected as the input source (p.18).

9 FM/AM

Switch between FM and AM (p.17).

0 Front display

Shows information about the operational status of this

unit.

A PRESET j / i

Selects a preset FM/AM station when TUNER is selected

as the input source (p.19).

B TUNING jj / ii

Selects the tuning frequency when TUNER is selected as

the input source (p.17).

C BASS +/–

Increases or decreases the low frequency response. The

center position produces a flat response (p.16).

D TREBLE +/–

Increases or decreases the high frequency response. The

center position produces a flat response (p.16).

E INPUT l / h

Selects the input source you want to listen to.

F SELECT/ENTER (jog dial)

Turn the dial to select a numeric value or setting, and press

the dial to confirm.

G RETURN

Returns to the previous indication of the front display.

H VOLUME control

Increases or decreases the sound output level.

Controls and functions

Front panel

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

HC D EFG

1234567

8 9:A B

Note

Controls and functions

6 En

1 Information display

Displays the current status (such as input name sound

mode name).

You can switch the information that is displayed when you

press DISPLAY (p.29).

2 STEREO

Lights up when the unit is receiving a stereo FM radio

signal.

3 TUNED

Lights up when the unit is receiving an FM/AM radio

station signal.

4 Speaker indicators

“SP A” lights up when the SPEAKERS A output is

enabled and “SP B” lights up when the SPEAKERS B

output is enabled.

5 MUTE

Blinks when audio is muted.

6 SLEEP

Lights up when the sleep timer is on.

y

You can change the brightness level of the front display by

pressing DIMMER on the remote control (p.8).

Front display

STEREO SP

MUTE

A

TUNED

SP

SLEEP

B

1

42 3 5 6

Controls and functions

7 En

INTRODUCTION

English

1 ANTENNA terminals

For connecting to FM and AM antennas (p.12).

2 DC OUT jack

For supplying power to a Yamaha AVaccessory. For

details, refer to the instruction manual of the AV

accessory.

3 NETWORK jack

For connecting to a network (p.13).

4 Power cable

For connecting to an AC wall outlet (p.13).

5 OPTICAL jack

For connecting to audio components equipped with

optical digital output (p.10).

6 COAXIAL jack

For connecting to audio components equipped with a

coaxial digital output (p.10).

7 CD jacks

For connecting to a CD player (p.10).

8 LINE 1-3 jacks

For connecting to analog audio components (p.10).

9 SPEAKERS terminals

Used to connect speakers (p.11).

Rear panel

A

B

PB

12 3

REC

SPEAKERS

CD LINE

ANTENNA

FM

AM

75Ω

DC OUT

5V

0.5A

NETWORK

DIGITAL

COAXIAL

OPTICAL

68 95

1

2 34

7

Controls and functions

8 En

1 Infrared signal transmitter

Sends infrared signals.

2 SLEEP

Sets the sleep timer (p.16).

3 DIMMER

Changes the brightness level of the front display.

Choose

brightness from 5 levels by pressing this key repeatedly.

4 SPEAKERS A/B

Turns on and off the set of speakers connected to the SPEAKERS

A and/or SPEAKERS B terminals on the rear panel of this unit

when the corresponding key is pressed.

5 Input selection keys

Select an input source for playback.

COAXIAL COAXIAL jack

OPTICAL OPTICAL jack

NET NETWORK jack (press repeatedly to select a

desired network source)

LINE 1-3 LINE 1-3 jacks

TUNER FM/AM tuner

CD CD jacks

6 Radio keys

Operate the FM/AM radio (p.17).

MODE Switches between “Stereo” and “Mono” for

FM radio reception (p.17).

FM Switches to FM radio.

AM Switches to AM radio.

TUNING jj / ii Select the radio frequency.

PRESET j / i Select a preset station.

7 POP-UP MENU

This button is not available for this unit.

8 Menu operation keys

Cursor keys Select a menu or a parameter.

(B/C/D/E)

ENTER Confirms a selected item.

RETURN Returns to the previous state.

9 SETUP

Displays the “Setup” menu (p.32).

0 VOLUME keys

Adjust the volume.

A OPTION

Displays the “Option” menu (p.30).

B DISPLAY

Switches information shown in the front display.

C A (power)

Turns on/off (standby) the unit.

D NOW PLAYING

Shows the playback information in the front display.

E HOME

Shows top-level menu in the front display.

F MUTE

Mutes the audio output.

G Playback keys

Let you play back and perform other operations for network

sources.

H SHUFFLE

Switches shuffle modes.

I REPEAT

Switches repeat modes.

Remote control

SETUP

POP-UP MENU

AM

FM

MODE

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

TUNER

CD

PRESET

TUNING

DIMMER

SLEEP

BA

SPEAKERS

HOME

NOW PLAYING

MUTE

OPTION

DISPLAY REPEAT SHUFFLE

VOLUME

RETURN

ENTER

1

2

C

E

F

H

I

D

3

4

5

6

8

7

9

:

G

B

A

Controls and functions

9 En

INTRODUCTION

English

■ Installing batteries

• Change all batteries if the operation range of the remote control

narrows.

• Before inserting new batteries, wipe the compartment clean.

■ Operation range

The remote controls transmit a directional infrared beam.

Be sure to aim the remote controls directly at the remote

control sensor on the front panel of this unit.

Using the remote controls

Notes

2

13

30° 30°

Remote control

Approximately

6 m (20 ft)

10 En

PREPARATION

• Do not connect this unit or other components to the main power until all connections between components are complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

Connections

Connecting speakers and source components

CAUTION

Connecting recording devices

You can connect audio recording devices to the LINE 3 (REC) jacks. This jack outputs the selected input signals (from COAXIAL,

OPTICAL, LINE 1-2, TUNER and CD).

• Be sure to use the LINE 3 (REC) jacks only for connecting recording devices.

• If you select LINE 3 as the input source, the audio output of the LINE 3 (REC) jacks will be muted.

A

B

PB

12 3

REC

SPEAKERS

CD LINE

ANTENNA

FM

AM

75Ω

DC OUT

5V

0.5A

NETWORK

DIGITAL

COAXIAL

OPTICAL

O

C

Audio

output

CD player

TV etc.

Speakers A

Audio output

(digital coaxial)

Audio

input

Audio

output

Speakers B

CD recorder, etc.

Audio output

(digital optical)

BD/DVD player, etc.

Notes

11 En

Connections

PREPARATION

English

■ Connecting speaker cables

Speaker cables have two wires. One is for connecting the

negative (-) terminal of the unit and the speaker, and the

other is for the positive (+) terminal. If the wires are

colored to prevent confusion, connect the black wire to the

negative and the other wire to the positive terminal.

a

Remove approximately 10 mm (3/8”) of insulation from the ends of

the speaker cable and twist the bare wires of the cable firmly together.

b Loosen the speaker terminal.

c Insert the bare wires of the cable into the gap on the side (upper

right or bottom left) of the terminal.

d Tighten the terminal.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of terminals

and the low frequency driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker. Refer to the speakers’ instruction

manuals for more information.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B on the front panel or on the remote control so that

both SP A and B light up on the front display.

Connecting the speakers

10 mm

(3/8")

aa

b

d

c

Note

A

B

SPE

A

This unit

Speaker

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

SPEAKERS A/B

SPEAKERS

A/B

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

DIMMER

SLEEP

BA

SPEAKERS

12 En

Connections

The antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide

sufficient signal strength. Connect each antenna correctly to the designated terminals.

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

■ Assembling the supplied AM antenna ■ Connecting the wires of the AM antenna

Connecting the FM and AM antennas

Note

PB

12 3

REC

CD LINE

ANTENNA

FM

AM

75Ω

DC OUT

5V

0.5A

DIGITAL

COAXIAL

OPTICAL

FM antenna

(included)

Outdoor AM antenna

Use 5 to 10 m of vinyl-covered wire

extended outdoors from a window.

Outdoor FM antenna

• The AM antenna should

always be connected, even if

an outdoor AM antenna is

connected to this unit.

• The AM antenna should be

placed away from this unit.

AM antenna

(included)

13 En

Connections

PREPARATION

English

You can enjoy Internet radio or music files stored on media servers, such as PCs and Network Attached Storage (NAS),

on the unit.

Connect the unit to your router with a commercially-available STP network cable (CAT-5 or higher straight cable).

y

• If you are using a router that supports DHCP, you do not need to

configure any network settings for the unit, as the network

parameters (such as the IP address) will be assigned

automatically to it. You only need to configure the network

settings if your router does not support DHCP or if you want to

configure the network parameters manually (p.33).

• You can check whether the network parameters (such as IP

address) are properly assigned to the unit in “Information”

(p.33) in the “Setup” menu.

• Some security software installed on your PC or the firewall

settings of network devices (such as a router) may block the

access of the unit to the network devices or the Internet. In these

cases, configure the security software or firewall settings

appropriately.

• Each server must be connected to the same subnet as the unit.

• To use the service via the Internet, broadband connection is

strongly recommended.

After all the connections are complete, plug in the power

cable.

Connecting to a network

A

B

PB

12 3

REC

SPEAKERS

CD LINE

ANTENNA

FM

AM

75Ω

DC OUT

5V

0.5A

NETWORK

DIGITAL

COAXIAL

OPTICAL

LAN

WAN

Network Attached Storage

(NAS)

Internet

Modem

Router

Network cable

PC

The unit (rear)

Mobile device

(such as iPhone)

Notes

Connecting power cable

To an AC wall outlet

14 En

Connections

Configure your devices connected to the network to play back music files stored on the devices, or configure your mobile

device to control this unit. Use the following configurations to suit your needs.

y

For details on Internet connection, please refer to the manual of your network devices.

❚ If you want to play the music files stored on your PC

You need to configure the media sharing setting of your PC.

Configure the media sharing setting of music files on

Windows Media Player 12. For details on sharing setting,

please refer to “Setting the media sharing of music files”

(p.22).

y

You can operate from your PC using Windows Media Player. For

details, refer to Windows Media Player help.

❚ If you want to play music files stored on your NAS

You need to configure the media sharing settings of your NAS.

Setup operations differ depending on your NAS. Refer to the

NAS manual.

y

• If you want to configure the network parameters manually, check

that you are using an IP address which is not used by other network

devices in your network.

• In case that you use DHCP and automatically obtain necessary

information for network, such as IP address. We recommend that

DHCP for the NAS normally be enabled.

❚ If you want to play iPod/iTunes with AirPlay

Select this unit from your iPod or from iTunes (p.27).

Check that the router being accessed by the iPod/iTunes is

connected to the same network as this unit.

❚ If you want to operate this unit with your mobile device

You need to download the dedicated application, and install it

(p.3).

y

• If you want to configure the network parameters manually, check

that you are using an IP address which is not used by other network

devices in your network.

• In case that you use DHCP and automatically obtain necessary

information for network, such as IP address. We recommend that

DHCP for the mobile device normally be enabled.

Setup of your network devices

15 En

BASIC

OPERATION

English

BASIC OPERATION

1 Press A (power) to turn on this unit.

2 Press the INPUT l / h selector on the front

panel (or press one of the input selection

keys on the remote control) to select the

input source you want to listen to.

3 Press SPEAKERS A and/or SPEAKERS B on

the front panel or on the remote control to

select speakers A and/or speakers B.

When speaker set A or speaker set B are turned on,

SP A or SP B is displayed on the front display

accordingly (p.6).

• When one set of speakers is connected using bi-wire connections,

or when using two sets of speakers simultaneously (A and B),

make sure SP A and SP B are displayed on the front display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to adjust the sound output level.

y

• You can adjust the tonal quality by using the BASS, TREBLE,

controls on the front panel.

• You can adjust the speaker balance in the “Setup” menu (p.16).

6 Press A (power) again to finish using this

unit and set it to standby mode.

Playback

Playing a source

Notes

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

A (power)

SPEAKERS A/B INPUT l / h VOLUME

A

VOLUME

SPEAKERS

A/B

SETUP

MUTE

VOLUME

RETURN

AM

FM

MODE

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

TUNER

CD

PRESET

TUNING

DIMMER

SLEEP

BA

SPEAKERS

Input selection

keys

(power)

16 En

Playback

■ Adjusting the BASS and TREBLE

controls

The BASS +/– and TREBLE +/– adjust high and low

frequency response.

When you adjust to “0”, produces a flat response.

BASS

Increases or decreases the low frequency response.

Control range: –10 to +10 (20 Hz)

TREBLE

Increases or decreases the high frequency response.

Control range: –10 to +10 (20 kHz)

y

BASS and TREBLE can be adjusted in the “Setup” menu (p.32).

■ Adjusting the speaker balance

The sound output balance of the left and right speakers to

compensate for sound imbalance caused by speaker

locations or listening room conditions.

To adjust the speaker balance, perform the following

steps.

1 Press SETUP on the remote control.

The “Setup” menu shown on the front display.

2

Press

B

/

C

to select “Balance” and press ENTER.

3 Press D/E to adjust speaker balance.

Control range: L+10 to R+10

4 To exit from the “Setup” menu, press SETUP

again.

Use this feature to automatically set this unit to standby

mode after a certain amount of time. The sleep timer is

useful when you are going to sleep while this unit is

playing or recording a source.

The sleep timer can only be set with the remote control.

1 Press SLEEP repeatedly to set the amount of

time before this unit is set to standby mode.

Each time you press SLEEP, the front display

changes as shown below.

The SLEEP indicator blinks while setting the amount

of time for the sleep timer.

If the sleep timer is set, the SLEEP indicator on the

front display lights up.

y

• To disable the sleep timer, select “Sleep Off”.

• The sleep timer setting can also be canceled by pressing

A (power) to set this unit to standby mode.

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

BASS

TREBLE

SETUP

POP-UP MENU HOME

NOW PLAYING

MUTE

VOLUME

RETURN

ENTER

SETUP

ENTER

Cursor keys

B / C / D / E

SPA

¡Network¡Setup

Setup

SPA

¡L------------R›

Balance

Using the sleep timer

Note

MODE

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

TUNER

CD

DIMMER

SLEEP

BA

SPEAKERS

A

SLEEP

(power)

SPA

Sleep¡120min.

SLEEP

P

A

n.

S

LEEP

SLEEP

17 En

BASIC

OPERATION

English

1 Press TUNER to select “TUNER” as the input

source.

2 Press FM or AM to select the reception band

(FM or AM).

3 Press and hold TUNING jj / ii for more than

1 second to begin tuning.

Press ii to tune in to a higher frequency.

Press jj to tune in to a lower frequency.

The frequency of the received station is shown in the

front display.

If a broadcast is being received, “TUNED” indicator

on the front display will be lit. If a stereo broadcast is

being received, the “STEREO” indicator will also lit.

If the tuning search does not stop at the desired

station because the station signals are weak, use the

following keys to set a frequency.

y

When the signal reception for an FM radio station is unstable,

switching to monaural may improve it.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM band reception mode to monaural

mode to improve reception.

1 Press MODE repeatedly to select “Stereo”

(automatic stereo mode) or “Mono”

(monaural mode) when this unit is tuned in to

an FM radio station.

When Mono is selected, FM broadcasts will be heard

in monaural sound.

The STEREO indicator on the front panel lights up while

listening to a station in stereo mode.

Listening to FM/AM radio

FM/AM tuning

TUNING jj / ii

MODE

FM

AM

TUNER

POP-UP MENU

AM

FM

MODE

LINE 1

COAXIAL

OPTICAL

NET

LINE 2 LINE 3

TUNER

CD

PRESET

TUNING

DIMMER

SLEEP

BA

SPEAKERS

HOME

NOW PLAYING

STEREO SPA

TUNED

¡¡¡¡FM¡98.50MHz

Frequency

Note

18 En

Listening to FM/AM radio

You can use the automatic preset tuning function to

automatically register FM stations as presets. This

function enables this unit to automatically tune in to FM

stations that have a strong signal and store up to 40 of

those stations in order. You can then easily recall any

preset station by selecting its preset number.

• If a station is registered to a preset number that already has a

station registered to it, the previously registered station is

overwritten.

• If the station you want to store is weak in signal strength, try

using the manual preset tuning method.

y

• FM stations registered as presets using the automatic preset

registration feature will be heard in stereo.

• Only Radio Data System broadcasting stations are stored

automatically by the Auto Preset function.

1 Press TUNER to select “TUNER” as the input

source.

2 Press OPTION on the remote control.

The “Option” menu is displayed (p.30).

3 Press B / C to select “Auto Preset”, and then

press ENTER.

This unit starts scanning the FM band about 5

seconds later from the lowest frequency upwards.

To begin scanning immediately, hold down the

ENTER key.

y

• Before scanning begins, you can specify the first preset number

to be used by pressing PRESET j / i or cursor key (B/C) on the

remote control.

• To cancel scanning, press FM, AM or RETURN.

When scanning is complete, “FINISH” is displayed

and then the display returns to original state.

You can manually register up to 40 FM/AM stations

(40 total). You can then easily recall any preset station by

selecting its preset number.

■ Registering a radio station manually

Select a radio station manually and register it to a preset

number.

1 Follow “FM/AM tuning” (p.17) to tune into the

desired radio station.

2

Hold down MEMORY for more than 2 seconds.

The first time that you do register a station, the selected

radio station will be registered to the preset number

“01”. Thereafter, each radio station you select will be

registered to the next empty (unused) preset number

after the most recently registered number.

y

To select a preset number for registering, press MEMORY once

after tuning into the desired radio station, press PRESET j / i to

select a preset number, and then press MEMORY again.

Automatic preset tuning

(FM stations only)

Notes

SETUP

POP-UP MENU

AM

FM

MODE

TUNER

CD

PRESET

TUNING

HOME

NOW PLAYING

MUTE

OPTION

VOLUME

RETURN

ENTER

PRESET j / i

TUNER

RETURN

FM

AM

OPTION

ENTER

Cursor keys

B

/

C

SPA

¡Auto¡Preset

Option

Manual tuning preset

SPA

¡01:FM¡87.50MHz

Ready

Preset number Frequency

STANDBY/ON

VOLUME

RETURN

PUSH - ENTER

TUNINGPRESET

FM/AM

MEMORY

BASS

TREBLE

INPUT

FM MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

MEMORY

PRESET j / i

STEREO SPA

TUNED

01¡:FM¡98.50MHz

¡98.50

Preset number

STEREO SPA

TUNED

02¡:Empty

¡98.50

“Empty” (not in use) or the frequency currently registered

Sivu latautuu ...

Yamaha R-N301 Ohjekirja

Yamaha R-N301 Ohjekirja

muilla kielillä

Liittyvät paperit

Muut asiakirjat